ASROCK K8UPGRADE-VM Manuale del proprietario

11

1

ASRock K8Upgrade-VM800 Motherboard

EnglishEnglish

English

Copyright Notice:Copyright Notice:

Copyright Notice:

No part of this installation guide may be reproduced, transcribed, transmitted, or

translated in any language, in any form or by any means, except duplication of

documentation by the purchaser for backup purpose, without written consent of

ASRock Inc.

Products and corporate names appearing in this guide may or may not be registered

trademarks or copyrights of their respective companies, and are used only for

identification or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:Disclaimer:

Disclaimer:

Specifications and information contained in this guide are furnished for informational

use only and subject to change without notice, and should not be constructed as a

commitment by ASRock. ASRock assumes no responsibility for any errors or

omissions that may appear in this guide.

With respect to the contents of this guide, ASRock does not provide warranty of any

kind, either expressed or implied, including but not limited to the implied warranties or

conditions of merchantability or fitness for a particular purpose.

In no event shall ASRock, its directors, officers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for

loss of profits, loss of business, loss of data, interruption of business and the like),

even if ASRock has been advised of the possibility of such damages arising from any

defect or error in the guide or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

ASRock Website: http://www.asrock.com

Published April 2005

22

2

ASRock K8Upgrade-VM800 Motherboard

EnglishEnglish

English

Motherboard LMotherboard L

Motherboard L

ayoutayout

ayout

1 PS2_USB_PWR1 Jumper 18 System Panel Header (PANEL1)

2 ATX 12V Power Connector (ATX12V1) 19 Game Port Header (GAME1)

3 CPU Fan Connector (CPU_FAN1) 20 Chassis Speaker Header (SPEAKER 1)

4 754-Pin CPU Socket 21 USB 2.0 Header (USB67, Blue)

5 CPU Heatsink Retention Module 22 Chassis Fan Connector (CHA_FAN1)

6 North Bridge Controller 23 Clear CMOS Jumper (CLRCMOS2)

7 184-pin DDR DIMM Slots (DDR1- 2) 24 AGP Slot (1.5V_AGP1)

8 J9 / J10 / J15 Jumpers 25 COM Port Header (COM1)

9 Infrared Module Header (IR1) 26 AMR Slot (AMR1)

10 Flash Memory 27 PCI Slots (PCI1- 2)

11 ATX Power Connector (ATXPWR1) 28 JR1 / JL1 Jumpers

12 Floppy Connector (FLOPPY1) 29 Front Panel Audio Header (AUDIO1)

13 Primary IDE Connector (IDE1, Blue) 30 Future CPU Port (FUTURE_CPU_PORT1)

14 Secondary IDE Connector (IDE2, Black) 31 Internal Audio Connector: AUX1 (White)

15 South Bridge Controller 32 Internal Audio Connector: CD1 (Black)

16 Primary Serial ATA Connector (SATA1) 33 Shared USB 2.0 Header (USB45, Blue)

17 Secondary Serial ATA Connector (SATA2) 34 J1 - J8 Jumpers

33

3

ASRock K8Upgrade-VM800 Motherboard

EnglishEnglish

English

ASRock I/O PlusASRock I/O Plus

ASRock I/O Plus

TMTM

TM

1 Parallel Port 7 USB 2.0 Ports (USB01)

2 RJ-45 Port 8 USB 2.0 Ports (USB23)

3 Line In (Light Blue) 9 VGA Port

4 Line Out (Lime) 10 PS/2 Keyboard Port (Purple)

5 Microphone (Pink) 11 PS/2 Mouse Port (Green)

6 Shared USB 2.0 Ports (USB45)

44

4

ASRock K8Upgrade-VM800 Motherboard

1.1.

1.

IntroductionIntroduction

Introduction

Thank you for purchasing ASRock K8Upgrade-VM800 motherboard, a reliable

motherboard produced under ASRock’s consistently stringent quality control. It de-

livers excellent performance with robust design conforming to ASRock’s commit-

ment to quality and endurance.

This Quick Installation Guide contains introduction of the motherboard and step-by-

step installation guide. More detailed information of the motherboard can be found in

the user manual presented in the Support CD.

Because the motherboard specifications and the BIOS software might

be updated, the content of this manual will be subject to change without

notice. In case any modifications of this manual occur, the updated

version will be available on ASRock website without further notice. You

may find the latest memory and CPU support lists on ASRock website

as well.

ASRock website http://www.asrock.com

1.11.1

1.1

Package ContentsPackage Contents

Package Contents

1 x ASRock K8Upgrade-VM800 Motherboard

(Micro ATX Form Factor: 9.0-in x 9.6-in, 22.9 cm x 24.4 cm)

1 x ASRock K8Upgrade-VM800 Quick Installation Guide

1 x ASRock K8Upgrade-VM800 Support CD

1 x Ultra ATA 66/100/133 IDE Ribbon Cable (80-conductor)

1 x 3.5-in Floppy Drive Ribbon Cable

1 x Serial ATA (SATA) Data Cable (Optional)

1 x Serial ATA (SATA) HDD Power Cable (Optional)

1 x ASRock I/O Plus

TM

Shield

1 x COM Port Bracket

1 x ASRock MR Card (Optional)

EnglishEnglish

English

55

5

ASRock K8Upgrade-VM800 Motherboard

EnglishEnglish

English

1.21.2

1.2

SpecificationsSpecifications

Specifications

Platform: Micro ATX Form Factor: 9.0-in x 9.6-in, 22.9 cm x 24.4 cm

CPU: 754-Pin Socket Supporting advanced 64-bit AMD Athlon

TM

64

and 32-bit Sempron Processor

Supports AMD’s Cool ‘n’ Quiet

TM

Technology (see CAUTION 1)

Chipsets: North Bridge: VIA K8M800 Chipset

FSB @ 800 MHz / 1.6 GT/s

South Bridge: VIA VT8237R Chipset

Supports USB 2.0, ATA 133, SATA 1.5Gb/s

Memory: 2 x DDR DIMM Slots: DDR1 and DDR2

Support PC3200 (DDR400) / PC2700 (DDR333) /

PC2100 (DDR266), Max. 2GB

IDE: IDE1: ATA 133 / Ultra DMA Mode 6

IDE2: ATA 133 / Ultra DMA Mode 6

Supports up to 4 IDE Devices

Serial ATA: 2 x SATA Connectors

Supports up to 2 SATA Devices at 1.5Gb/s Data Transfer Rate

Floppy Port: Supports up to 2 Floppy Disk Drives

Audio: 5.1 channels AC’97 Audio

OnBoard VGA: Intergrated UniChrome PRO 3D/2D Graphics Controller

, supports DirectX 8.1

LAN: Speed: 802.3u (10/100 Ethernet), Supports Wake-On-LAN

Hardware Monitor: CPU Temperature Sensing

Motherboard Temperature Sensing

CPU Overheat Shutdown to Protect CPU Life

(ASRock U-COP)(see CAUTION 2)

CPU Fan Tachometer

Chassis Fan Tachometer

Voltage Monitoring: +12V, +5V, +3.3V, Vcore

Future CPU Port: Supports CPU upgrade from AMD 754-Pin CPU to

AMD 939-Pin CPU (see page 8 for details)

PCI Slots: 2 x PCI Slots, PCI Specification 2.2

AGP slot: 1 x AGP Slot

Supports 1.5V, 8X / 4X AGP Card (see CAUTION 3)

AMR slot: 1 slot, supports ASRock MR card (Optional)

USB 2.0: 8 USB 2.0 Ports:

6 Ready-to-Use USB 2.0 Ports on the I/O Panel

Plus 2 On-Board Headers Supporting 2 Extra USB 2.0 Ports

(see CAUTION 4)

66

6

ASRock K8Upgrade-VM800 Motherboard

EnglishEnglish

English

ASRock I/O Plus

TM

: 1 PS/2 Mouse Port, 1 PS/2 Keyboard Port

1 VGA Port

1 Parallel Port (ECP/EPP Support)

6 Ready-to-Use USB 2.0 Ports

1 RJ-45 Port

Audio Jack: Line In / Line Out / Microphone

COM Port: 1 COM Port Header to support a COM port module

BIOS: AMI Legal BIOS

Supports “Plug and Play”

ACPI 2.0 Compliance Wake Up Events

SMBIOS 2.3.1 Support

CPU Frequency Stepless Control

(only for advanced users’ reference, see CAUTION 5)

OS: Microsoft

®

Windows

®

98 SE / ME / 2000 / XP compliant

CAUTION!

1. For power-saving sake, it is strongly recommended to enable AMD’s Cool ‘n’

Quiet

TM

technology under Windows system. See APPENDIX on page 39 of

“User Manual” in the Support CD to enable AMD’s Cool ‘n’ Quiet

TM

technology.

2. While CPU overheat is detected, the system will automatically shutdown.

Before you resume the system, please check if the CPU fan on the motherboard

functions properly and unplug the power cord, then plug it back again. To

improve heat dissipation, remember to spray thermal grease between the

CPU and the heatsink when you install the PC system.

3. Do NOT use a 3.3V AGP card on the AGP slot of this motherboard!

It may cause permanent damage!

4. Power Management for USB 2.0 works fine under Microsoft

®

Windows

®

XP

SP1 / 2000 SP4. It may not work properly under Microsoft

®

Windows

®

98/ ME.

5. Although this motherboard offers stepless control, it is not recommended to

perform over-clocking. Frequencies other than the recommended CPU bus

frequencies may cause the instability of the system or damage the CPU.

77

7

ASRock K8Upgrade-VM800 Motherboard

2.2.

2.

InstallationInstallation

Installation

Pre-installation PrecautionsPre-installation Precautions

Pre-installation Precautions

Take note of the following precautions before you install mother-

board components or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any

component. Failure to do so may cause severe damage to the

motherboard, peripherals, and/or components.

2. To avoid damaging the motherboard components due to static

electricity, NEVER place your motherboard directly on the car-

pet or the like. Also remember to use a grounded wrist strap or

touch a safety grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a

grounded antstatic pad or in the bag that comes with the

component.

5. When placing screws into the screw holes to secure the

motherboard to the chassis, please do not over-tighten the screws!

Doing so may damage the motherboard.

2.12.1

2.1

CPU InstallationCPU Installation

CPU Installation

Step 1. Unlock the socket by lifting the lever up to a 90° angle.

Step 2. Position the CPU directly above the socket such that its marked corner

matches the base of the socket lever.

Step 3. Carefully insert the CPU into the socket until it fits in place.

The CPU fits only in one correct orientation. DO NOT force the CPU

into the socket to avoid bending of the pins.

Step 4. When the CPU is in place, press it firmly on the socket while you push

down the socket lever to secure the CPU. The lever clicks on the side tab

to indicate that it is locked.

Step 5. Install CPU fan and heatsink. For proper installation, please kindly refer to

the instruction manuals of your CPU fan and heatsink vendors.

EnglishEnglish

English

88

8

ASRock K8Upgrade-VM800 Motherboard

2.22.2

2.2

Installation of Memory Modules (DIMM)Installation of Memory Modules (DIMM)

Installation of Memory Modules (DIMM)

K8Upgrade-VM800 motherboard provides two 184-pin DDR (Double Data Rate)

DIMM slots.

Please make sure to disconnect power supply before adding or

removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break

on the slot.

The DIMM only fits in one correct orientation. It will cause permanent

damage to the motherboard and the DIMM if you force the DIMM into the

slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully

snap back in place and the DIMM is properly seated.

2.32.3

2.3

Expansion SlotsExpansion Slots

Expansion Slots

(Future CPU Port, PCI Slots, AGP Slot, and AMR Slots)(Future CPU Port, PCI Slots, AGP Slot, and AMR Slots)

(Future CPU Port, PCI Slots, AGP Slot, and AMR Slots)

There are 1 Future CPU Port, 2 PCI slots, 1 AGP slot and 1 AMR slot on K8Upgrade-

VM800 motherboard.

Future CPU Port (Yellow-Colored Port):

Future CPU Port allows you to upgrade your AMD 754-Pin CPU to AMD 939-Pin CPU by

installing an add-on ASRock 939CPU Board into this future CPU Port on K8Upgrade-

VM800 motherboard. Before you upgrade the 754-Pin CPU to the 939-Pin CPU, it is

necessary to adjust the jumper settings for those required jumpers on K8Upgrade-

VM800 motherboard. Please refer to the table below for the correct jumper settings.

EnglishEnglish

English

99

9

ASRock K8Upgrade-VM800 Motherboard

This yellow-colored Future CPU Port is not an AGP slot! Please do

NOT insert any AGP card into it!

EnglishEnglish

English

J10

CPU Type Jumper Settings

939-Pin CPU

(Using add-on

ASRock 939CPU

Board)

754-Pin CPU

(Default)

J1 J2

J3 J4

J5 J6

J7 J8

J1 J2

J3 J4

J5 J6

J7 J8

J15

J9

J10

J9

1010

10

ASRock K8Upgrade-VM800 Motherboard

EnglishEnglish

English

NOTE

When adjusting the jumper settings, you may use the tool, Jumper Cap Remover, to help you

removing the jumper caps more easily. This Jumper Cap Remover is bundled in your motherboard

package, and please follow the “Jumper Cap Remover Instruction” to use it properly.

PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI

interface.

AGP slot: The AGP slot is used to install a graphics card. The ASRock AGP slot has

a special design of clasp that can securely fasten the inserted graphics

card.

Please do NOT use a 3.3V AGP card on the AGP slot of this motherboard!

It may cause permanent damage! For the voltage information of your

graphics card, please check with the graphics card vendors.

AMR slot: AMR slot is used to insert an ASRock MR card (optional) with v.92

Modem functionality.

Installing an expansion cardInstalling an expansion card

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read the

documentation of the expansion card and make necessary hardware

settings for the card before you start the installation.

Step 2. Remove the bracket facing the slot that you intend to use. Keep the screw

for later use.

Step 3. Align the card connector with the slot and press firmly until the card is

completely seated on the slot.

Step 4. Fasten the card to the chassis with screws.

1111

11

ASRock K8Upgrade-VM800 Motherboard

Short Open

2.4 Jumpers Setup2.4 Jumpers Setup

2.4 Jumpers Setup

The illustration shows how jumpers are

setup. When the jumper cap is placed on

pins, the jumper is “Short”. If no jumper cap

is placed on the pins, the jumper is “Open”.

The illustration shows a 3-pin jumper whose

pin1 and pin2 are “Short” when jumper cap

is placed on these 2 pins.

Jumper Setting

PS2_USB_PWR1 Short pin2, pin3 to enable

(see p.2, No. 1) +5VSB (standby) for PS/2 or

USB wake up events.

Note: To select +5VSB, it requires 2 Amp and higher standby current provided by

power supply.

JR1 / JL1 Jumper

(see p.2, No. 28)

Note: If the jumpers JR1 and JL1 are short, both the front panel and the rear panel

audio connectors can work.

Clear CMOS Jumper

(CLRCMOS2)

(see p.2, No. 23)

Note: CLRCMOS2 allows you to clear the data in CMOS. The data in CMOS includes

system setup information such as system password, date, time, and system

setup parameters. To clear and reset the system parameters to default setup,

please turn off the computer andunplug the power cord from the power

supply. After waiting for 15 seconds, use a jumper cap to short the Clear

CMOS jumper for 5 seconds. After shorting the Clear CMOS jumper, please

remove the jumper cap. However, please do not clear the CMOS right after you

update the BIOS. If you need to clear the CMOS when you just finish updating

the BIOS, you must boot up the system first, and then shut it down before you

do the clear-CMOS action.

EnglishEnglish

English

1212

12

ASRock K8Upgrade-VM800 Motherboard

EnglishEnglish

English

connect the black end

to the IDE devices

connect the blue end

to the motherboard

the red-striped side to Pin1

2.5 Connectors2.5 Connectors

2.5 Connectors

Connectors are NOT jumpers. DO NOT place jumper caps over these

connectors. Placing jumper caps over the connectors will cause perma-

nent damage of the motherboard!

Connector Figure Description

Floppy Connector

(33-pin FLOPPY1)

(see p.2, No. 12)

Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the

connector.

Primary IDE Connector (Blue) Secondary IDE Connector (Black)

(39-pin IDE1, see p.2, No. 13) (39-pin IDE2, see p.2, No. 14)

80-conductor, ATA 66/100/133 cable

Note: If you use only one IDE device on this motherboard, please set the IDE

device as “Master”. Please refer to the instruction of your IDE device vendor

for the details. Besides, to optimize compatibility and performance, please

connect your hard disk drive to the primary IDE connector (IDE1, blue) and

CD-ROM to the secondary IDE connector (IDE2, black).

Serial ATA Connectors These two Serial ATA (SATA)

(SATA1: see p.2, No. 16) connectors support SATA data

(SATA2: see p.2, No. 17) cables for internal storage

devices. The current SATA

interface allows up to 1.5 Gb/s

data transfer rate.

Serial ATA (SATA) Either end of the SATA data

Data Cable cable can be connected to the

SATA hard disk or the SATA

connector on the motherboard.

SATA2

SATA1

1313

13

ASRock K8Upgrade-VM800 Motherboard

Serial ATA (SATA) Please connect the black end of

Power Cable SATA power cable to the power

(Optional) connector on each drive. Then

connect the white end of SATA

power cable to the power

connector of the power supply.

USB 2.0 Header ASRock I/O Plus

TM

provides you

(9-pin USB67) 6 ready-to-use USB 2.0 ports on

(see p.2, No. 21) the rear panel. If the rear USB

ports are not sufficient, this

USB 2.0 header is available to

support 2 extra USB 2.0 ports.

Shared USB 2.0 Header This USB45 header is shared

(9-pin USB45) with the USB 2.0 ports 4,5 on

(see p.2, No. 33) ASRock I/O Plus

TM

. When using

the front panel USB ports by

attaching the front panel USB

cable to this header (USB45), the

USB ports 4,5 on ASRock I/O

Plus

TM

will not be able to function.

Infrared Module Header This header supports an

(5-pin IR1) optional wireless transmitting and

(see p.2, No. 9) receiving infrared module.

Internal Audio Connectors These connectors allow you to

(4-pin CD1, 4-pin AUX1) receive stereo audio input from

(CD1: see p.2, No. 32) sound sources such as a CD-

(AUX1: see p.2, No. 31) ROM, DVD-ROM, TV tuner card,

or MPEG card.

Front Panel Audio Header This is an interface for front panel

(9-pin AUDIO1) audio cable that allows conve-

(see p.2, No. 29) nient connection and control of

audio devices.

CD1

AUX1

connect to the

power supply

connect to the SATA

HDD power connector

EnglishEnglish

English

1414

14

ASRock K8Upgrade-VM800 Motherboard

EnglishEnglish

English

System Panel Header This header accommodates

(9-pin PANEL1) several system front panel

(see p.2, No. 18) functions.

Chassis Speaker Header Please connect the chassis(4-

pin SPEAKER 1) speaker to this header.

(see p.2, No. 20)

Chassis Fan Connector Please connect a chassis fan

(3-pin CHA_FAN1) cable to this connector and

(see p.2, No. 22) match the black wire to the

ground pin.

CPU Fan Connector Please connect a CPU fan cable

(3-pin CPU_FAN1) to this connector and match the

(see p.2, No. 3) black wire to the ground pin.

ATX Power Connector Please connect an ATX power

(20-pin ATXPWR1) supply to this connector.

(see p.2, No. 11)

COM Port Header This COM port header is used

(9-pin COM1) to support a COM port module.

(see p.2, No. 25)

ATX 12V Power Connector Please note that it is necessary

(4-pin ATX12V1) to connect a power supply with

(see p.2, No. 2) ATX 12V plug to this connector.

Failing to do so will cause power

up failure.

1515

15

ASRock K8Upgrade-VM800 Motherboard

Game Port Header Connect a Game cable to this

(15-pin GAME1) header if the Game port bracket

(see p.2, No. 19) is installed.

2.62.6

2.6

Serial ASerial A

Serial A

TT

T

A (SAA (SA

A (SA

TT

T

A) Hard Disks InstallationA) Hard Disks Installation

A) Hard Disks Installation

This motherboard supports Serial ATA (SATA) hard disks. You may install SATA

hard disks on this motherboard for internal storage devices. This section will

guide you to install the SATA hard disks.

STEP 1: Install the SATA hard disks into the drive bays of your chassis.

STEP 2: Connect the SATA power cable to the SATA hard disk.

STEP 3: Connect one end of the SATA data cable to the motherboard’s SATA

connector.

STEP 4: Connect the other end of the SATA data cable to the SATA hard disk.

2.72.7

2.7

Hot Plug FHot Plug F

Hot Plug F

unction for SAunction for SA

unction for SA

TT

T

A HDDsA HDDs

A HDDs

K8Upgrade-VM800 motherboard supports Hot Plug function for SATA devices.

What is Hot Plug Function?

If the SATA HDDs are NOT set for RAID configuration, it is called “Hot

Plug” for the action to insert and remove the SATA HDDs while the

system is still power-on and in working condition. However, please note

that it cannot perform Hot Plug if the OS has been installed into the SATA

HDD.

WARNING!

Although this motherboard supports Hot Plug function for SATA devices,

there are still some limitation. Please ensure to read the instruction in the

Support CD before you use Hot Plug function. Failure to do so may lose

the data in the SATA HDDs or damage the SATA HDDs. For the detailed

instruction, please refer to the document in the Support CD at the

following path:

..\ SATA RAID BIOS

EnglishEnglish

English

1616

16

ASRock K8Upgrade-VM800 Motherboard

EnglishEnglish

English

2.82.8

2.8

Installing Windows 2000 / Windows XP /Installing Windows 2000 / Windows XP /

Installing Windows 2000 / Windows XP /

Windows XP 64-bit With RAID FunctionsWindows XP 64-bit With RAID Functions

Windows XP 64-bit With RAID Functions

If you want to install Windows 2000 / Windows XP / Windows XP-64bit OS on

your system with RAID functions, please refer to the below methods for proper

installation according to the different Windows OS versions.

2.8.12.8.1

2.8.1

Installing Windows 2000 / Windows XP withInstalling Windows 2000 / Windows XP with

Installing Windows 2000 / Windows XP with

RAID FunctionsRAID Functions

RAID Functions

If you want to install Windows 2000 / Windows XP OS on your SATA

HDDs with RAID functions, please follow the below steps.

STEP 1: Make a SATA Driver Diskette.

A. Insert the ASRock Support CD into your optical drive to boot your

system.

B. During POST at the beginning of system boot-up, press <F11> key, and

then a window for boot devices selection appears. Please select CD-

ROM as the boot device.

C. When you see the message on the screen, “Do you want to generate

Serial ATA driver diskette [YN]?”, press <Y>.

D. Then you will see these messages,

Please insert a diskette into the floppy drive.

WARNING! Formatting the floppy diskette will

lose ALL data in it!

Start to format and copy files [YN]?

Please insert a floppy diskette into the floppy drive, and press <Y>.

E. The system will start to format the floppy diskette and copy SATA

drivers into the floppy diskette.

STEP 2: Use “SATA RAID BIOS” to set RAID configuration.

Before you start to configure the RAID function, you need to check the

installation guide in the Support CD for proper configuration. Please refer

to the document in the Support CD, “Guide to SATA Hard Disks Installation

and RAID Configuration”, which is located in the folder at the following

path: .. \ SATA RAID BIOS

STEP 3: Install Windows 2000 / Windows XP OS on your system.

After making a SATA driver diskette and using “SATA RAID BIOS” to set

RAID configuration, you can start to install Windows 2000 / Windows XP

on your system.

1717

17

ASRock K8Upgrade-VM800 Motherboard

EnglishEnglish

English

2.8.22.8.2

2.8.2

Installing Windows XP 64-bit WithInstalling Windows XP 64-bit With

Installing Windows XP 64-bit With

RAIDRAID

RAID

FunctionsFunctions

Functions

If you want to install Windows XP 64-bit OS on your SATA HDDs with RAID

functions, please follow the below steps.

STEP 1: Make a SATA Driver Diskette.

A. Insert the floppy diskette into your floppy drive.

B. Copy the SATA 64-bit drivers to your floppy diskette.

The SATA 64-bit drivers are located at the following path in the Support CD:

.. \ 64bit SATA Driver

STEP 2: Install Windows XP 64-bit OS on your system.

After making a SATA driver diskette, you can start to install Windows XP 64-

bit on your system.

After the installation of Windows 2000 / Windows XP / Windows XP 64-bit OS,

if you want to manage RAID functions, you are allowed to use both “SATA RAID

BIOS” and “VIA RAID Tool” for RAID configuration. Please refer to the document

in the Support CD, “Guide to SATA Hard Disks Installation and RAID Configuration”,

which is located in the folder at the following path: .. \ SATA RAID BIOS and the

document in the support CD, “Guide to VIA RAID Tool”, which is located in the

folder at the following path: .. \ VIA RAID Tool

1. Windows 98 / Windows ME does not support RAID functions.

2. If you want to use “VIA RAID Tool” in Windows environment, please install

SATA drivers from the Support CD again so that “VIA RAID Tool” will be

installed to your system as well.

1818

18

ASRock K8Upgrade-VM800 Motherboard

EnglishEnglish

English

2.92.9

2.9

Installing Windows 98 / ME / 2000 / XP / XP 64-bitInstalling Windows 98 / ME / 2000 / XP / XP 64-bit

Installing Windows 98 / ME / 2000 / XP / XP 64-bit

Without RAID FunctionsWithout RAID Functions

Without RAID Functions

If you want to install Windows 98 / ME / 2000 / XP / XP 64-bit on your SATA HDDs

without RAID functions or you want to install Windows 98 / ME / 2000 / XP / XP

64-bit on your IDE HDDs instead of SATA HDDs, please refer to the below methods

for proper installation according to the different Windows OS versions.

2.9.1 2.9.1

2.9.1

Installing Windows 98 / ME Without RAID Installing Windows 98 / ME Without RAID

Installing Windows 98 / ME Without RAID

Functions Functions

Functions

If you want to install Windows 98 / ME on your SATA HDDs without RAID

functions or you want to install Windows 98 / ME on your IDE HDDs instead

of SATA HDDs, please follow the below steps.

STEP 1: Install Windows 98 / ME OS on your system.

You can start to install Windows 98 / ME on your system directly.

2.9.2 2.9.2

2.9.2

Installing Windows XP / 2000 / XP 64-bit Installing Windows XP / 2000 / XP 64-bit

Installing Windows XP / 2000 / XP 64-bit

Without RAID Functions Without RAID Functions

Without RAID Functions

If you want to install Windows XP / 2000 / XP 64-bit on your SATA HDDs

without RAID functions or you want to install Windows XP / 2000 / XP 64-bit

on your IDE HDDs instead of SATA HDDs, please follow the below steps.

STEP 1: Set Up BIOS.

A. Enter BIOS SETUP UTILITY Advanced screen IDE Configuration.

B. Set the “SATA Operation Mode” option from [RAID] to [non-RAID].

STEP 2: Install Windows 2000 / XP / XP 64-bit OS on your system.

After setting up BIOS, you can start to install Windows 2000 / XP / XP

64-bit on your system.

If you don’t want to set up RAID functions, there is no need to make a SATA

driver diskette.

1919

19

ASRock K8Upgrade-VM800 Motherboard

3. BIOS Information3. BIOS Information

3. BIOS Information

The Flash Memory on the motherboard stores BIOS Setup Utility. When you start up

the computer, please press <F2> during the Power-On-Self-Test (POST) to enter

BIOS Setup utility; otherwise, POST continues with its test routines. If you wish to

enter BIOS Setup after POST, please restart the system by pressing <Ctl> + <Alt> +

<Delete>, or pressing the reset button on the system chassis.

The BIOS Setup program is designed to be user-friendly. It is a menu-driven program,

which allows you to scroll through its various sub-menus and to select among the

predetermined choices. For the detailed information about BIOS Setup, please refer

to the User Manual (PDF file) contained in the Support CD.

4. Software Suppor4. Software Suppor

4. Software Suppor

t CD informationt CD information

t CD information

This motherboard supports various Microsoft

®

Windows

®

operating systems: 98 SE/

ME / 2000 / XP. The Support CD that came with the motherboard contains necessary

drivers and useful utilities that will enhance motherboard features.

To begin using the Support CD, insert the CD into your CD-ROM drive. It will display

the Main Menu automatically if “AUTORUN” is enabled in your computer. If the Main

Menu does not appear automatically, locate and double-click on the file “ASSETUP.

EXE” from the “BIN” folder in the Support CD to display the menus.

EnglishEnglish

English

2020

20

ASRock K8Upgrade-VM800 Motherboard

La pagina sta caricando ...

ASROCK K8UPGRADE-VM Manuale del proprietario

Questo manuale è adatto anche per

ASROCK K8UPGRADE-VM Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti