ASROCK P4V88 PLUS Manuale del proprietario

11

1

ASRock P4V88/P4V88+ Motherboard

Copyright Notice:Copyright Notice:

Copyright Notice:

No part of this installation guide may be reproduced, transcribed, transmitted, or

translated in any language, in any form or by any means, except duplication of

documentation by the purchaser for backup purpose, without written consent of

ASRock Inc.

Products and corporate names appearing in this guide may or may not be registered

trademarks or copyrights of their respective companies, and are used only for

identification or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:Disclaimer:

Disclaimer:

Specifications and information contained in this guide are furnished for informational

use only and subject to change without notice, and should not be constructed as a

commitment by ASRock. ASRock assumes no responsibility for any errors or

omissions that may appear in this guide.

With respect to the contents of this guide, ASRock does not provide warranty of any

kind, either expressed or implied, including but not limited to the implied warranties or

conditions of merchantability or fitness for a particular purpose.

In no event shall ASRock, its directors, officers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for

loss of profits, loss of business, loss of data, interruption of business and the like),

even if ASRock has been advised of the possibility of such damages arising from any

defect or error in the guide or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

ASRock Website: http://www.asrock.com

Published April 2005

EnglishEnglish

English

ASRock P4V88/P4V88+ Motherboard

22

2

Motherboard LMotherboard L

Motherboard L

ayoutayout

ayout

1 PS2_USB_PWR1 Jumper 16 Floppy Connector (FLOPPY1)

2 CPU Fan Connector (CPU_FAN1) 17 System Panel Header (PANEL1)

3 CPU Heatsink Retention Module 18 Chassis Speaker Header (SPEAKER 1)

4 CPU Socket 19 Chassis Fan Connector (CHA_FAN1)

5 North Bridge Controller 20 USB 2.0 Header (USB67, Blue)

6 2 x 184-pin DDR DIMM Slots 21 Infrared Module Header (IR1)

(Dual Channel A: DDR1, DDR3; Blue) 22 Game Connector (GAME1)

7 ATX 12V Connector (ATX12V1) 23 5 x PCI Slots (PCI1- 5)

8 Secondary IDE Connector (IDE2, Black) 24 Flash Memory

9 Primary IDE Connector (IDE1, Blue) 25 JL1 Jumper

10 2 x 184-pin DDR DIMM Slots 26 JR1 Jumper

(Dual Channel B: DDR2, DDR4; Black) 27 Front Panel Audio Header (AUDIO1)

11 AGP Slot (1.5V_AGP1) 28 Internal Audio Connector: AUX1 (White)

12 Secondary Serial ATA Connector (SATA2) 29 Internal Audio Connector: CD1 (Black)

13 Primary Serial ATA Connector (SATA1) 30 Shared USB 2.0 Header (USB4_5, Blue)

14 South Bridge Controller 31 ATX Power Connector (ATXPWR1)

15 Clear CMOS Jumper (CLRCMOS1)

EnglishEnglish

English

33

3

ASRock P4V88/P4V88+ Motherboard

ASRock I/O PlusASRock I/O Plus

ASRock I/O Plus

TMTM

TM

1 Parallel Port 7 USB 2.0 Ports (USB0, USB1)

2 RJ-45 Port 8 USB 2.0 Ports (USB2, USB3)

3 Line In (Light Blue) 9 Serial Port: COM1

4 Line Out (Lime) 10 PS/2 Keyboard Port (Purple)

5 Microphone (Pink) 11 PS/2 Mouse Port (Green)

6 USB 2.0 Ports (USB4, USB5)

EnglishEnglish

English

ASRock P4V88/P4V88+ Motherboard

44

4

1. Introduction1. Introduction

1. Introduction

Thank you for purchasing ASRock P4V88/P4V88+ motherboard, a reliable mother-

board produced under ASRock’s consistently stringent quality control. It delivers

excellent performance with robust design conforming to ASRock’s commitment to

quality and endurance.

This Quick Installation Guide contains introduction of the motherboard and step-by-

step installation guide. More detailed information of the motherboard can be found in

the user manual presented in the Support CD.

Because the motherboard specifications and the BIOS software might

be updated, the content of this manual will be subject to change

without notice. In case any modifications of this manual occur, the

updated version will be available on ASRock website without further

notice. You may find the latest memory and CPU support lists on

ASRock website as well.

ASRock website

http://www.asrock.com

1.1 Package Contents1.1 Package Contents

1.1 Package Contents

ASRock P4V88/P4V88+ Motherboard

(ATX Form Factor: 12.0-in x 8.6-in, 30.5 cm x 21.8 cm)

ASRock P4V88/P4V88+ Quick Installation Guide

ASRock P4V88/P4V88+ Support CD

One 80-conductor Ultra ATA 66/100/133 IDE Ribbon Cable

One Ribbon Cable for a 3.5-in Floppy Drive

One Serial ATA (SATA) Cable

One Serial ATA (SATA) HDD Power Cable(Optional)

One ASRock I/O Plus

TM

Shield

EnglishEnglish

English

55

5

ASRock P4V88/P4V88+ Motherboard

1.2 Specifications1.2 Specifications

1.2 Specifications

Platform: ATX Form Factor: 12.0-in x 8.6-in, 30.5 cm x 21.8 cm

CPU: Socket 478, supports Intel

®

Pentium

®

4

(Prescott, Northwood,

Willimate) / Celeron

®

processor

Chipsets: North Bridge:

VIA PT880, FSB @ 800/533/400 MHz,

with Intel

®

Hyper-Threading Technology ready

(see CAUTION 1)

South Bridge:

VIA VT8237, supports USB 2.0, ATA 133, SATA 1.5Gb/s

Memory: 4 DDR DIMM slots: DDR1, DDR2, DDR3, and DDR4

2 DDR DIMM Slots Support PC3200 (DDR400), Max. 2GB,

4 DDR DIMM Slots Support PC2700 (DDR333) /

PC2100 (DDR266), Max. 3.5GB,

Dual Channel Memory Technology support

(see CAUTION 2)

IDE: IDE1: ATA 133 / Ultra DMA Mode 6

IDE2: ATA 133 / Ultra DMA Mode 6

Support up to 4 IDE devices

Serial ATA: 2 SATA connectors, support up to 1.5Gb/s data transfer rate

Floppy Port: Supports up to 2 floppy disk drives

Audio: 5.1 channels AC’97 Audio

LAN: Speed: 802.3u (10/100 Ethernet), supports Wake-On-LAN

Hardware Monitor: CPU temperature sensing,

Chassis temperature sensing,

CPU overheat shutdown to protect CPU life

(ASRock U-COP)(see CAUTION 3),

CPU fan tachometer,

Chassis fan tachometer,

Voltage monitoring: +12V, +5V, +3V, Vcore

PCI slots: 5 slots with PCI Specification 2.2

AGP slot: 1 AGP slot, supports 1.5V, 8X/4X AGP card (see CAUTION 4)

USB 2.0: 8 USB 2.0 ports:

include 6 ready-to-use USB 2.0 ports on the rear panel,

plus one on-board header supporting 2 extra USB 2.0 ports

(see CAUTION 5)

EnglishEnglish

English

ASRock P4V88/P4V88+ Motherboard

66

6

ASRock I/O Plus

TM

: 1 PS/2 mouse port, 1 PS/2 keyboard port,

1 serial port: COM1,

1 parallel port: ECP/EPP support,

6 ready-to-use USB 2.0 ports,

1 RJ 45 port,

Audio Jack: Line In / Line Out / Microphone

BIOS: AMI BIOS,

Supports “Plug and Play”,

ACPI 1.1 compliance wake up events,

Supports jumperfree,

SMBIOS 2.3.1 support,

CPU frequency stepless control

(only for advanced users’ reference, see CAUTION 6)

OS: Microsoft

®

Windows

®

98SE / ME / 2000 / XP compliant

CAUTION!

1. About the setting of “Hyper Threading Technology”, please check page 25

in the Support CD.

2. This motherboard supports Dual Channel Memory Technology. Before you

implement Dual Channel Memory Technology, make sure to read the

installation guide of memory modules on page 8 for proper installation.

3. While CPU overheat is detected, the system will automatically shutdown.

Before you resume the system, please check if the CPU fan on the

motherboard functions properly and unplug the power cord, then plug it

back again. To improve heat dissipation, remember to spray thermal

grease between the CPU and the heatsink when you install the PC system.

4. Do NOT use a 3.3V AGP card on the AGP slot of this motherboard!

It may cause permanent damage!

5. Power Management for USB 2.0 works fine under Microsoft

®

Windows

®

XP

SP1/2000 SP4. It may not work properly under Microsoft

®

Windows

®

98/

ME.

6. Although this motherboard offers stepless control, it is not recommended

to perform over-clocking. Frequencies other than the recommended CPU

bus frequencies may cause the instability of the system or damage the

CPU.

EnglishEnglish

English

77

7

ASRock P4V88/P4V88+ Motherboard

2. Installation2. Installation

2. Installation

Pre-installation PrecautionsPre-installation Precautions

Pre-installation Precautions

Take note of the following precautions before you install motherboard

components or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any

component. Failure to do so may cause severe damage to the

motherboard, peripherals, and/or components.

2. To avoid damaging the motherboard components due to static electricity,

NEVER place your motherboard directly on the carpet or the like. Also

remember to use a grounded wrist strap or touch a safety grounded

object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a grounded

antstatic pad or in the bag that comes with the component.

2.1 CPU Installation2.1 CPU Installation

2.1 CPU Installation

STEP 1: Unlock the socket by lifting the lever up to a 90

o

angle.

STEP 2: Position the CPU directly above the socket such that its marked

corner matches the base of the socket lever.

STEP 3: Carefully insert the CPU into the socket until it fits in place.

The CPU fits only in one correct orientation. DO NOT force the CPU

into the socket to avoid bending of the pins.

STEP 4: When the CPU is in place, press it firmly on the socket while you

push down the socket lever to secure the CPU. The lever clicks on

the side tab to indicate that it is locked.

STEP 5: Install CPU fan and heatsink. For proper installation, please kindly

refer to the instruction manuals of your CPU fan and heatsink vendors.

EnglishEnglish

English

ASRock P4V88/P4V88+ Motherboard

88

8

2.2 Installation of Memory Modules (DIMM)2.2 Installation of Memory Modules (DIMM)

2.2 Installation of Memory Modules (DIMM)

P4V88/P4V88+ motherboard provides four 184-pin DDR (Double Data Rate) DIMM

slots, and supports Dual Channel Memory Technology. For dual channel configuration,

you always need to install identical (the same brand, speed, size and chip-type)

DDR DIMM pair in the slots of the same color. In other words, you have to install

identical DDR DIMM pair in Dual Channel A (DDR1 and DDR3; Blue slots; see p.2

No. 6) or identical DDR DIMM pair in Dual Channel B (DDR2 and DDR4; Black slots;

see p.2 No. 10), so that Dual Channel Memory Technology can be activated. This

motherboard also allows you to install four DDR DIMMs for dual channel configuration,

and please install identical DDR DIMMs in all four slots. You may refer to the Dual

Channel Memory Configuration Table below.

Dual Channel Memory Configurations

DDR1 DDR2 DDR3 DDR4

(Blue Slot) (Black Slot) (Blue Slot) (Black Slot)

(1) Populated - Populated -

(2) - Populated - Populated

(3) Populated Populated Populated Populated

1. If you want to install two memory modules, for optimal compatibility

and reliability, it is recommended to install them in the slots of the

same color. In other words, install them either in the set of blue slots

(DDR1 and DDR3), or in the set of black slots (DDR2 and DDR4).

2. If only one memory module or three memory modules are installed

in the DDR DIMM slots on this motherboard, it is unable to activate

the Dual Channel Memory Technology.

3. If a pair of memory modules is NOT installed in the same Dual

Channel, for example, installing a pair of memory modules in DDR1

and DDR2, it is unable to activate the Dual Channel Memory

Technology.

EnglishEnglish

English

99

9

ASRock P4V88/P4V88+ Motherboard

Installing a DIMMInstalling a DIMM

Installing a DIMM

Please make sure to disconnect power supply before adding or

removing DIMMs or the system components.

STEP 1: Unlock a DIMM slot by pressing the retaining clips outward.

STEP 2: Align a DIMM on the slot such that the notch on the DIMM matches the

break on the slot.

The DIMM only fits in one correct orientation. It will cause permanent

damage to the motherboard and the DIMM if you force the DIMM into the

slot at incorrect orientation.

STEP 3: Firmly insert the DIMM into the slot until the retaining clips at both ends

fully snap back in place and the DIMM is properly seated.

EnglishEnglish

English

ASRock P4V88/P4V88+ Motherboard

1010

10

2.3 Expansion Slots (PCI and AGP Slots)2.3 Expansion Slots (PCI and AGP Slots)

2.3 Expansion Slots (PCI and AGP Slots)

There are 5 PCI slots and 1 AGP slot on P4V88/P4V88+ motherboard.

PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI

interface.

AGP slot: The AGP slot is used to install a graphics card. The ASRock AGP slot has

a special design of clasp that can securely fasten the inserted graphics

card.

Please do NOT use a 3.3V AGP card on the AGP slot of this

motherboard! It may cause permanent damage! For the voltage

information of your AGP card, please check with the AGP card

vendors.

Installing an expansion cardInstalling an expansion card

Installing an expansion card

STEP 1: Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read the

documentation of the expansion card and make necessary hardware

settings for the card before you start the installation.

STEP 2: Remove the bracket facing the slot that you intend to use. Keep the screws

for later use.

STEP 3: Align the card connector with the slot and press firmly until the card is

completely seated on the slot.

STEP 4: Fasten the card to the chassis with screws.

EnglishEnglish

English

1111

11

ASRock P4V88/P4V88+ Motherboard

2.4 Jumpers Setup2.4 Jumpers Setup

2.4 Jumpers Setup

The illustration shows how jumpers are

setup. When the jumper cap is placed on

pins, the jumper is “Short”. If no jumper cap

is placed on pins, the jumper is “Open”. The

illustration shows a 3-pin jumper whose pin1

and pin2 are “Short” when jumper cap is

placed on these 2 pins.

Jumper Setting

PS2_USB_PWR1 Short pin2, pin3 to enable

(see p.2 No. 1) +5VSB (standby) for PS/2

or USB wake up events.

Note: To select +5VSB, it requires 2 Amp and higher standby current provided

by power supply.

JR1(see p.2 No. 26)

JL1(see p.2 No. 25)

Note: If the JL1 and JR1 jumpers are short, both the front panel and the rear panel

audio connectors can work.

Clear CMOS

(CLRCMOS1, 2-pin jumper)

(see p.2 No. 15)

Note: CLRCMOS1 allows you to clear the data in CMOS. The data in CMOS includes

system setup information such as system password, date, time, and system

setup parameters. To clear and reset the system parameters to default setup,

please turn off the computer andunplug the power cord, then use a jumper

cap to short the pins on CLRCMOS1 for 3 seconds. Please remember to

remove the jumper cap after clearing the CMOS. If you need to clear the CMOS

when you just finish updating the BIOS, you must boot up the system first, and

then shut it down before you do the clear-CMOS action.

Short

Open

2-pin jumper

EnglishEnglish

English

ASRock P4V88/P4V88+ Motherboard

1212

12

2.5 Onboard Headers and Connectors2.5 Onboard Headers and Connectors

2.5 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place

jumper caps over these headers and connectors. Placing jumper caps

over the headers and connectors will cause permanent damage of the

motherboard!

FDD Connector

(33-pin FLOPPY1)

(see p.2 No. 16)

Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the

connector.

Primary IDE Connector (Blue) Secondary IDE Connector (Black)

(39-pin IDE1, see p.2 No. 9) (39-pin IDE2, see p.2 No. 8)

Note: If you use only one IDE device on this motherboard, please set the IDE

device as “Master”. Please refer to the instruction of your IDE device vendor

for the details. Besides, to optimize compatibility and performance, please

connect your hard disk drive to the primary IDE connector (IDE1, blue) and

CD-ROM to the secondary IDE connector (IDE2, black).

Serial ATA Connectors These two Serial ATA (SATA)

(SATA1: see p.2 No. 13) connectors support SATA data

(SATA2: see p.2 No. 12) cables for internal storage

devices. The current SATA

interface allows up to 1.5 Gb/s

data transfer rate.

Serial ATA (SATA) Either end of the SATA data cable

Data Cable can be connected to the SATA

hard disk or the SATA connector

on the motherboard.

connect the black end

to the IDE devices

connect the blue end

to the motherboard

80-conductor ATA 66/100/133 cable

the red-striped side to Pin1

SATA1

SATA2

EnglishEnglish

English

1313

13

ASRock P4V88/P4V88+ Motherboard

Serial ATA (SATA) Please connect the black end of

Power Cable SATA power cable to the power

(Optional) connector on the drive. Then

connect the white end of SATA

power cable to the power

connector of the power supply.

USB 2.0 Header ASRock I/O Plus

TM

provides you

(9-pin USB67) 6 ready-to-use USB 2.0 ports on

(see p.2 No. 20) the rear panel. If the rear USB

ports are not sufficient, this

USB 2.0 header is available to

support 2 extra USB 2.0 ports.

Shared USB 2.0 Header This USB4_5 connector is shared

(9-pin USB4_5) with the USB 2.0 ports 4,5 on

(see p.2 No. 30) ASRock I/O Plus

TM

. When using

the front panel USB ports by

attaching the front panel USB

cable to this connector

(USB4_5), the USB ports 4,5 on

ASRock I/O Plus

TM

will not be able

to function.

Infrared Module Header This header supports an optional

(5-pin IR1) wireless transmitting and

(see p.2 No. 21) receiving infrared module.

Internal Audio Connectors These connectors allow you

(4-pin CD1, 4-pin AUX1) to receive stereo audio input

(CD1: see p.2 No. 29) from sound sources such as

(AUX1: see p.2 No. 28) a CD-ROM, DVD-ROM, TV

tuner card, or MPEG card.

Front Panel Audio Header This is an interface for the front

(9-pin AUDIO1) panel audio cable that allows

(see p.2 No. 27) convenient connection and

control of audio devices.

CD1

AUX1

connect to the

power supply

connect to the SATA

HDD power connector

EnglishEnglish

English

ASRock P4V88/P4V88+ Motherboard

1414

14

System Panel Header This header accommodates

(9-pin PANEL1) several system front panel

(see p.2 No. 17) functions.

Chassis Speaker Header Please connect the chassis

(4-pin SPEAKER 1) speaker to this header.

(see p.2 No. 18)

Chassis Fan Connector Please connect the chassis fan

(3-pin CHA_FAN1) cable to this connector and

(see p.2 No. 19) match the black wire to the

ground pin.

CPU Fan Connector Please connect the CPU fan

(3-pin CPU_FAN1) cable to this connector and

(see p.2 No. 2) match the black wire to the

ground pin.

Game Connector Connect a Game cable to this

(15-pin GAME1) connector if the Game port

(see p.2 No. 22) bracket is installed.

ATX Power Connector Please connect an ATX power

(20-pin ATXPWR1) supply to this connector.

(see p.2 No. 31)

ATX 12V Connector Please note that it is necessary

(4-pin ATX12V1) to connect a power supply with

(see p.2 No. 7) ATX 12V plug to this connector

so that it can provides sufficient

power. Failing to do so will cause

the failure to power up.

EnglishEnglish

English

1515

15

ASRock P4V88/P4V88+ Motherboard

2.62.6

2.6

Serial ASerial A

Serial A

TT

T

A (SAA (SA

A (SA

TT

T

A) Hard Disks InstallationA) Hard Disks Installation

A) Hard Disks Installation

This motherboard adopts VIA VT8237 southbridge chipset that supports Serial

ATA (SATA) hard disks. You may install SATA hard disks on this motherboard for

internal storage devices. This section will guide you to install the SATA hard disks.

STEP 1: Install the SATA hard disks into the drive bays of your chassis.

STEP 2: Connect the SATA power cable to the SATA hard disk.

STEP 3: Connect one end of the SATA data cable to the motherboard’s SATA

connector.

STEP 4: Connect the other end of the SATA data cable to the SATA hard disk.

2.72.7

2.7

Hot Plug and Hot Swap FHot Plug and Hot Swap F

Hot Plug and Hot Swap F

unctions for SAunctions for SA

unctions for SA

TT

T

A HDDsA HDDs

A HDDs

P4V88/P4V88+ motherboard supports Hot Plug and Hot Swap functions for SATA

Devices.

NOTE

What is Hot Plug Function?

If the SATA HDDs are NOT set for RAID configuration, it is called “Hot

Plug” for the action to insert and remove the SATA HDDs while the

system is still power-on and in working condition.

However, please note that it cannot perform Hot Plug if the OS has

been installed into the SATA HDD.

What is Hot Swap Function?

If SATA HDDs are built as RAID1 then it is called “Hot Swap” for the

action to insert and remove the SATA HDDs while the system is still

power-on and in working condition.

EnglishEnglish

English

ASRock P4V88/P4V88+ Motherboard

1616

16

EnglishEnglish

English

2.82.8

2.8

Installing Windows 2000 / Windows XP With RAIDInstalling Windows 2000 / Windows XP With RAID

Installing Windows 2000 / Windows XP With RAID

FunctionsFunctions

Functions

If you want to install Windows 2000 / Windows XP OS on your SATA

HDDs with RAID functions, please follow the below steps.

STEP 1: Make a SATA Driver Diskette.

A. Insert the ASRock Support CD into your optical drive to boot your

system.

B. During POST at the beginning of system boot-up, press <F11> key,and

then a window for boot devices selection appears. Please select CD-

ROM as the boot device.

C. When you see the message on the screen, “Do you want to generate

Serial ATA driver diskette [YN]?”, press <Y>.

D. Then you will see these messages,

Please insert a diskette into the floppy drive.

WARNING! Formatting the floppy diskette will

lose ALL data in it!

Start to format and copy files [YN]?

Please insert a floppy diskette into the floppy drive, and press <Y>.

E. The system will start to format the floppy diskette and copy SATA

drivers into the floppy diskette.

STEP 2: Use “SATA RAID BIOS” to set RAID configuration.

Before you start to configure the RAID function, you need to check the

installation guide in the Support CD for proper configuration. Please refer

to the document in the Support CD, “Guide to SATA Hard Disks Installation

and RAID Configuration”, which is located in the folder at the following

path: .. \ SATA RAID BIOS

STEP 3: Install Windows 2000 / Windows XP OS on your system.

After making a SATA driver diskette and using “SATA RAID BIOS” to set

RAID configuration, you can start to install Windows 2000 / Windows XP

on your system.

After the installation of Windows 2000 / Windows XP OS, if you want to manage

RAID functions, you are allowed to use both “SATA RAID BIOS” and “VIA RAID Tool”

for RAID configuration. Please refer to the document in the Support CD, “Guide to

SATA Hard Disks Installation and RAID Configuration”, which is located in the folder at

the following path: .. \ SATA RAID BIOS and the document in the support CD, “Guide

to VIA RAID Tool”, which is located in the folder at the following path: .. \ VIA RAID

Tool

1. Windows 98 / Windows ME does not support RAID functions.

2. If you want to use “VIA RAID Tool” in Windows environment, please install

SATA drivers from the Support CD again so that “VIA RAID Tool” will be

installed to your system as well.

1717

17

ASRock P4V88/P4V88+ Motherboard

EnglishEnglish

English

2.92.9

2.9

Installing Windows 98 / ME / 2000 / XP Without RAIDInstalling Windows 98 / ME / 2000 / XP Without RAID

Installing Windows 98 / ME / 2000 / XP Without RAID

FunctionsFunctions

Functions

If you want to install Windows 98 / ME / 2000 / XP on your SATA HDDs without

RAID functions or you want to install Windows 98 / ME / 2000 / XP on your IDE

HDDs instead of SATA HDDs, please refer to the below methods for proper

installation according to the different Windows OS versions.

2.9.1 Installing Windows 98 / ME Without RAID 2.9.1 Installing Windows 98 / ME Without RAID

2.9.1 Installing Windows 98 / ME Without RAID

Functions Functions

Functions

If you want to install Windows 98 / ME on your SATA HDDs without RAID

functions or you want to install Windows 98 / ME on your IDE HDDs instead

of SATA HDDs, please follow the below steps.

STEP 1: Install Windows 98 / ME OS on your system.

You can start to install Windows 98 / ME on your system directly.

2.9.2 Installing Windows 2000 / XP Without RAID 2.9.2 Installing Windows 2000 / XP Without RAID

2.9.2 Installing Windows 2000 / XP Without RAID

Functions Functions

Functions

If you want to install Windows 2000 / XP on your SATA HDDs without RAID

functions or you want to install Windows 2000 / XP on your IDE HDDs instead

of SATA HDDs, please follow the below steps.

STEP 1: Set Up BIOS.

A. Enter BIOS SETUP UTILITY Advanced screen IDE Configuration.

B. Set the “SATA Operation Mode” option from [RAID] to [non-RAID].

STEP 2: Install Windows 2000 / XP OS on your system.

After setting up BIOS, you can start to install Windows 2000 / XP on your

system.

If you don’t want to set up RAID functions, there is no need to make a SATA

driver diskette.

ASRock P4V88/P4V88+ Motherboard

1818

18

3. BIOS Information3. BIOS Information

3. BIOS Information

The Flash Memory on the motherboard stores BIOS Setup Utility. When you start up

the computer, please press <F2> during the Power-On-Self-Test (POST) to enter

BIOS Setup utility; otherwise, POST continues with its test routines. If you wish to

enter BIOS Setup after POST, please restart the system by pressing <Ctl> + <Alt> +

<Delete>, or pressing the reset button on the system chassis.

The BIOS Setup program is designed to be user-friendly. It is a menu-driven program,

which allows you to scroll through its various sub-menus and to select among the

predetermined choices. For the detailed information about BIOS Setup, please refer

to the User Manual (PDF file) contained in the Support CD.

4. Software Suppor4. Software Suppor

4. Software Suppor

t CD informationt CD information

t CD information

This motherboard supports various Microsoft

®

Windows

®

operating systems: 98 SE/

ME / 2000 / XP. The Support CD that came with the motherboard contains necessary

drivers and useful utilities that will enhance motherboard features.

To begin using the Support CD, insert the CD into your CD-ROM drive. It will display

the Main Menu automatically if “AUTORUN” is enabled in your computer. If the Main

Menu does not appear automatically, locate and double-click on the file

“ASSETUP.EXE” from the BIN folder in the Support CD to display the menus.

EnglishEnglish

English

1919

19

ASRock P4V88/P4V88+ Motherboard

2020

20

® ®

®

La pagina sta caricando ...

ASROCK P4V88 PLUS Manuale del proprietario

Questo manuale è adatto anche per

ASROCK P4V88 PLUS Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti