Tasco 119422 Manuale utente

Trail Cam

Model#: 119422

04-13

Instruction Manual

2

TABLE OF CONTENTS PAGE

ENGLISH

FrANçAIS

ESPAñOL

DEuTSCH

ITALIANO

3-31

32-67

68-102

103-143

144-180

3

IMPOrTANT NOTE

Congratulations on your purchase of one of the best trail

cameras on the market! Tasco is very proud of this camera and

we are sure you will be pleased with it as well. We appreciate

your business and want to earn your trust. Please refer to the

notes below and the instructions in this manual to ensure that

you are completely satisﬁed with this product.

If your Tasco Trail Cam does not seem to be functioning

properly or if you are having photo/video quality issues,

please check the Troubleshooting/FAQ section on pages

25-28.

Problems are often due to something simple that was

overlooked, or require only changing one setting to solve.

If your problem continues after trying the solutions in the

Troubleshooting/FAQ section, please call Tasco Customer

Service at (800) 423-3537. In Canada, call (800) 361-5702.

Tasco recommends using 8 Energizer

®

Lithium AA batteries in this

Trail Cam to obtain maximum battery life

Do not mix old and new batteries

Do not mix battery types-use ALL lithium or ALL alkaline

Rechargeable batteries are not recommended

Tasco recommends using SanDisk

®

SD and SDHC Cards

(up to 32GB capacity) in this Trail Cam

ENGLISH

4

INTRODUCTION

About the Trail Cam

The Tasco Trail Cam is a digital scouting camera. It can be triggered by any

movement of game in a location, detected by a highly sensitive Passive Infra-

Red (PIR) motion sensor, and then take high quality pictures (up to 6MP still

photos), or video clips.

The Trail Cam consumes very little power (less than 300mA) in a stand-

by (surveillance) state. This means it can deliver up to six months stand-by

operation time when the device is powered by eight AA alkaline batteries, and

up to nine months utilizing lithium AA batteries. Once motion in the monitored

area is detected, the digital camera unit will be triggered at once (typically

within one second) and then automatically take photos or videos according

to previously programmed settings. The Trail Cam is equipped with 32

built-in "black" infrared LEDs that function as a ﬂash, so that it delivers clear

photos or videos (in black & white) even in the dark without being detected,

and it can take color photos or videos under sufﬁcient daylight. The Trail

Cam is designed for outdoor use and is resistant against water and snow.

Applications

The Trail Cam can be used as a trail camera for hunting or scouting game.

It is also suitable for surveillance usage.

PARTS AND CONTROLS

The Trail Cam provides the following connections for external devices: USB

port, SD card slot, AV Out, and external DC power in (Fig. 1).

A 3-way power switch is used to select the main operating modes: OFF,

SETUP, and ON (Fig. 2).

A control key interface with six keys is primarily used in SETUP mode to

select operational functions and parameters. As shown in Fig. 2, these keys

are: UP, DOWN, LEFT, RIGHT, OK and MENU. Four of the keys can also

perform a second function (shortcut operations in SETUP mode) in addition

to their main function: The DOWN key can be used to set the camera to

Photo mode (still camera icon), and the UP key can set the camera to Video

mode (movie camera icon). The RIGHT key also serves as the manual shutter

(“SHOT”) button of the camera and the OK key switches the camera to

the Playback (“REPLAY”) mode. These secondary functions are indicated by

5

icons or text above the key as shown in Fig. 2.

Fig. 2: Button and

Switch Guide

Fig. 1: Connections

A/V Out

USB Port

SD Card Slot

DC In

ON

SETUP

OFF

LED IR Flash

Motion/ Low

Battery Indicator

Lens

Lock Hole

PIR Sensor

FRONT VIEW

BACK VIEW

LCD Screen

Power/Mode

Switch

UP/Video

DOWN/Photo

LEFT

MENU

OK/Replay

RIGHT/Shot

Cable to Battery

Compartment

Video Mic

DC in

Cover Plug

6

INSTALLING THE BATTERIES AND SD CARD

Before you begin learning how to use your Trail Cam, you will ﬁrst need to

install a set of batteries and insert an SD card. Although that may only take

you a minute, there are some important notes about both batteries and SD

cards you should be aware of, so please take the time to read the following

directions and cautions:

Loading Batteries

After opening the two latches on the right side of

the Trail Cam, you will see that the Trail Cam

can hold 8 batteries. The four batteries on the left

form one group, while the four on the right form the

other group, each providing 6 volts in parallel. For

maximum battery life, you should install a full set of

eight batteries. The Trail Cam may also be operated

by just four batteries installed in the ﬁrst group only

(see right). Battery life will be shorter with 4 batteries,

but the camera will operate normally. Whether you

use 4 or 8, be sure to insert each battery with correct

polarity (negative or “ﬂat” end facing the spring in

each vertical battery compartment "column").

Tasco recommends using eight new lithium AA (Energizer

®

brand) or alkaline

AA batteries. NiMh Rechargeable batteries are not recommended, as the

lower voltage they produce can cause operational issues. It is also possible

to use a lead-acid external battery cell with 6V output or suitable AC adapter-see

below for more details.

Using an External Power Source (optional, user provided)

Optionally, you can connect an external 6V DC power source to the “DC

In” jack at the bottom of the Trail Cam. It is recommended to use a power

source with a current output greater than 1000mA. However, during bright

daytime operation when no ﬂash is required, the Trail Cam can function with

much less current (>400mA). Please use a compatible power source cable

(not provided) to connect the external DC power source with the power input

jack of the Trail Cam, making sure that the polarity is correct. Note: The

power connector is a 4.0x1.7mm coaxial DC power plug with positive “tip”

(inside pin) polarity (Radio Shack P/N 274-1532 or equivalent).

7

If both an external power source is connected and batteries are installed, the

Trail Cam will be powered by the external power source.

When the batteries become weak, the low-battery indicator LED will glow

blue, indicating the batteries should be changed (pg 5, “Front View”).

Inserting the SD Card

The Trail Cams have 32MB internal memory, which can hold only about 35

photos (@ 4MP resolution). This is handy for testing and getting familiar with

the camera, but you will no doubt want to leave the camera unattended for

longer than a day, so using an SD card is recommended. Insert the SD card

(with the camera’s power switch in the OFF position) before beginning to

operate the camera. Don’t insert or remove the SD card when the power

switch is in the ON position.

The Trail Cam uses a standard SD (Secure Digital) memory card to save

photos (in .jpg format) and/or videos (in .avi format). SD and SDHC (High

Capacity) cards up to a maximum 32GB capacity are supported. Before

inserting the SD card into the card slot after opening the camera’s front

cover, please make sure that the write-protect switch on the side of the card

is “off” (NOT in the “Lock” position). The following describes how to insert and

remove the SD card:

• Insert the SD card into the card slot with its label side upwards (see

below). A “click” sound indicates that the card is installed successfully.

If the wrong side of the card is facing up, you will not be able to insert

it without force-there is only one correct way to insert cards. If the SD

card is not installed correctly, the device will not display an SD card icon

on the LCD in SETUP mode (the SD card icon displayed after switching

to SETUP mode will have a “lock” symbol inside it in it if the card is locked).

Formatting the SD card by using the Trail Cam’s “Format” parameter

before using it for the ﬁrst time is recommended, especially when a

card has been used in other devices (see “Changing Menu Parameter

Settings” for details).

• To take out the SD card, just gently push in the

card (do not try to pull it out without pushing

in ﬁrst). The card is released from the slot and

ready to be removed when you hear the click.

WARNING

Be sure the camera’s power is switched OFF

before inserting or removing SD cards or batteries.

8

USING THE TRAIL CAM

Once you’ve prepared your Trail Cam by properly installing batteries and

an SD card, you could simply take it outside, strap it to a tree, switch it on

and leave-and you might get some great photos that are exactly what you

wanted. However, we highly recommend that you ﬁrst spend some additional

time indoors with this manual and your camera until you know a bit more

about what the 3-way switch and those control keys do. If nothing else, you’ll

probably want to at least set the date and time so the camera will imprint

them (or not-it’s your option) on your photos as they are taken, learn how to

set the camera to shoot video clips instead of still photos if you like, and read

some tips about mounting it on a tree.

THE OFF, ON, AND SETUP MODES

The Trail Cam has three basic operational modes:

• OFF mode: Power switch in the OFF position.

• ON mode: Power switch in the ON position (LCD screen is off.)

• SETUP mode: Power switch at SETUP position (LCD screen is on).

OFF MODE

The OFF mode is the “safe” mode when any actions must be taken, e.g.,

replacing the SD card or batteries, or transporting the device. You will also

use OFF mode if you connect the camera to a computer’s USB port later to

download your photos/videos. And of course, when you are storing or not

using the camera, you will switch it to OFF. Please note that even in the OFF

mode the Trail Cam still consumes power at a very low level. Therefore, it’s a

good idea to take the batteries out of the battery compartment if the camera

will not be used for a long time.

ON MODE

Anytime after the batteries and SD card have been inserted, you can switch

on the camera. When the power switch is moved to the top position, the

camera will enter into the ON (Live) mode. The motion indicator LED (pg.

6, “Front View”) will blink red for about 10 seconds. This interval allows time

for you to close the Trail Cam’s front cover, lock it, and leave the monitored

area. Once in the ON mode, no manual controls are needed or possible

(the control keys have no effect). The Trail Cam will take photos or videos

9

automatically (according to its current parameter settings) when it is triggered

by the PIR sensor’s detection of activity in the area it covers.

You can either move the power switch directly from OFF to ON mode, or stop

at the SETUP position ﬁrst to change one or more settings, then move the

switch to ON after you have ﬁnished doing so.

SETUP MODE

In the SETUP mode you can check and change the settings of the Trail Cam

with the help of its built-in LCD (or a monitor connected to the AV out jack).

These settings, found in the SETUP Menu, let you change the photo or video

resolution, interval between photos, switch the time imprint on, etc. Moving

the power switch to the SETUP position will turn on the LCD display, and

you will see an information screen that shows how many images have been

taken, the battery level, camera or video mode, etc (see Fig. 3, next page).

NOTE: Always move the power switch from OFF to SETUP mode. It

is possible that the camera could lockup if it is switched from ON to

SETUP mode. If this occurs, simply move the switch to OFF and then

push it up to SETUP again.

SETUP Mode Shortcut Keys/Functions

As mentioned earlier in “Parts & Controls”, four of the keys below the LCD

have secondary, “shortcut” functions when the camera is switched to SETUP

mode (but the MENU key has not been pressed):

• Press the UP key to quickly set the camera to shoot video clips.

• Press the DOWN key to quickly set the camera to take still photos.

• Press the RIGHT key to manually trigger the shutter. This is useful

for testing the camera-make sure you are in SETUP mode, press the

RIGHT key, and a few seconds later a photo or video (depending on

how the camera was set) will be saved to the SD card (or internal

memory if no card is inserted). The “number of images taken” counter

on the bottom left of the LCD will increase by one. If the display

indicates “SD PROTECTED” when you press the SHOT key, switch

the camera OFF, remove the SD card and slide its protect switch off.

• Press the OK key to replay (review or playback) photos/videos on a

connected TV monitor. See “Playing Back Photos/Videos” (pg. 22) for

more details.

10

Fig. 3: SETUP Information Screen

2

Video Mode

Video Sound On

Video Resolution

Available Video Recording Time

Video Mode

High

2

Still Photo Mode

Time Stamp

Time Lapse On

# of Photos Taken Remaining Photo Capacity

Date:Month-Day-Year

Battery Level

Image Size (Resolution)

SD Card Status

Time

Hour:Minute:Second

Camera (Still Photo) Mode

4

11

USING THE SETUP MENU TO CHANGE

SETTINGS

The main purpose of the SETUP mode is to allow you to change the settings

of the camera’s parameters (14 different ones are available) so your Trail

Cam operates exactly the way you want it to. You will do this by entering the

SETUP Menu and pressing the keys below the LCD display, which will show

you each parameter and its setting.

Changing Parameter Settings in SETUP Mode

A wide range of options or “parameters” are provided to allow you to set

the Trail Cam to your operational preferences. To change the setting of

any parameter you must ﬁrst switch to the SETUP mode. Once in SETUP

mode, pressing the MENU button will allow you to select any parameter and

change its setting. The name of the parameter and its current setting will be

shown on the LCD. Pressing the RIGHT or LEFT key scrolls to the next or

previous parameter (RIGHT key to move on to the next parameter and LEFT

key to go back to the previous parameter), and pressing the UP or DOWN

key lets you select a different setting for the currently displayed parameter.

Once you have selected your preferred new setting for a parameter, press

the OK button to save the new setting (actually change it). When have are

ﬁnished changing the settings of one or more parameters, press MENU

again to exit the SETUP menu. MENU can also be pressed anytime you

want to cancel changing a parameter’s setting after a new setting has been

selected (but OK has not been pressed yet). After setting the parameters

to your preferences, be sure to move the switch to ON to begin actually

taking photos or videos. No images will be captured if the switch is left in the

SETUP position (unless you press the RIGHT/Shot key after exiting the menu)-

in fact, the camera will power off automatically after a few seconds with no

key pressed.

Only one setting is displayed at a time, starting with the current setting for the

parameter when it is ﬁrst selected (Fig. 4a, next page). To change the setting,

use the UP/DOWN keys to display the new setting you want (Fig. 4b), then

press OK to “Execute” (make the actual change to this setting). If you want to

conﬁrm this setting is now the current one, just press the RIGHT key to scroll

to the next parameter, then press LEFT to go back again to the previous one.

You should see the parameter setting you just made.

12

Fig. 4: Selecting Parameter Settings

(4a)

(4b)

Press MENU

Press DOWN

Press OK

EXAMPLES-Changing the Settings of Some Common Parameters

Following this page, you will ﬁnd tables listing all of the parameters found in

the SETUP Menu, along with their possible settings (or range of settings),

and a detailed description of what the parameter controls and what

the settings do. If you read the previous section detailing how to select

parameters and change their settings, you should be able to dive right in, ﬁnd

the parameter(s) you want, and setup the camera to your preferences. But

maybe you’d rather walk through an example or two ﬁrst:

To change any parameter’s setting, always start with the power switch in the

SETUP position. After the LCD comes on, press the MENU key.

The ﬁrst parameter you will see when you ﬁrst enter the SETUP Menu is

“Mode”. To change it from its default setting of “Camera” (still photos) to

“Video” (shoot video clips), press the DOWN key to select the “Video”

setting. Press the OK key to “Execute” (Set) the new setting you’ve selected

for this parameter.

Now press the RIGHT key to move to another parameter in the Menu.

Pressing it four times will take you to “Video Length”. Try using the UP and

DOWN keys to scroll through the range of settings, then press OK to lock in

your setting for the length of each video clip the camera shoots.

13

Pressing the RIGHT key several more times will get you to the “Default

Set” parameter. Select “Execute” (using UP or DOWN) and press OK to

restore all parameters (including the Mode and Video Length parameters

you changed a minute ago) back to their original factory default settings. The

default settings for each parameter are indicated in bold type in the SETUP

Menu tables on the next several pages.

Be sure to set the current date and time, using the “Set Clock” parameter,

if you choose to change the “Time Stamp” parameter setting to “On” since

that will tell the camera to imprint the date and time on each of the images

it captures.

Time Lapse Feature

Time Lapse is a revolutionary new feature for the Tasco Trail Cam, which

allows you to monitor your food plots or ﬁeld edges with time lapse images

or video. When set to “On”, the Trail Cam will take a photo (or record a video

clip) automatically at your choice of intervals during a block of time you set

up for each day, without requiring a trigger from an active animal. This

has the advantage of giving you the ability to monitor the edge of a ﬁeld that

might be 50 or 150 yards away from the camera out of the PIR sensor’s

range. The result is an effective range much greater than it would normally be,

with the camera dependant on triggers generated by nearby animals. This is

a great tool for hunters to scout an entire ﬁeld with only one camera.

If an animal does enter the area covered by the IR sensor and generate

a trigger event during a time in between the Time Lapse intervals you set,

the camera will capture an image or video just as it normally would, based

on your other menu settings. Here’s how to setup and use Time Lapse (be

sure you’ve set the current time with “Set Clock” ﬁrst, so your Time Lapse

recording will stop and start at the correct times of day):

1. Move the main switch to SETUP, then press MENU.

2. Keep pressing the RIGHT key, stepping through the Setup Menu until

you reach Time Lapse.

3. With “On” selected (press UP/DOWN to toggle between On/Off),

press OK. This takes you to the screen to set Start and Stop time,

which determines the clock times when the Time Lapse recording will

begin and end for each day. You can set these times to the exact hour

14

and minute you want, for a recording “block” that lasts anywhere from

just a minute to a full 24 hours.

4. Set the [Start] and [Stop] times, beginning with the Start hour, using

the UP/DOWN keys to change the setting. The hour setting is based

on a 24-hour clock, with “00” hours = midnight, “12” hours = noon,

“23” hrs = 11PM, etc. To move to the next setting, press the RIGHT

key, change the minute for the Start time with UP/DOWN, then on to

the hour and minute settings for the Stop time.

5. After you ﬁnish setting the last time setting (Stop minutes), another

press of the RIGHT key will take you to the setting for Interval. This

lets you control how often a photo or video clip is recorded during the

block of time you deﬁned with the Start and Stop settings. Note that

for videos, this is independent of the length of each video recording-

it’s how often videos are recorded, not how long each one lasts.

Your options are 60 minutes, 30 minutes, 15 minutes, 5 minutes (this

is the default), or 1 minute-use the UP/DOWN keys to select your

preference, then press OK to save it.

6. Here’s an example of how the camera would operate, based on the

following Time Lapse settings:

Time Lapse: On

[Start]: 16:00

[Stop]: 18:30

[Interval]: 15M

These settings would cause the camera to take a photo (or video,

depending on which you have it set for) beginning at 4 PM, then

another one at 4:15, 4:30, etc.–one every 15 minutes, until the Time

Lapse recording stops at 6:30 PM. The next day, the camera would

again record an image or video once every 15 minutes between 4 and

6:30 PM. Remember, this is independent of normal triggers due to

animal activity–even if no animals enter the IR sensor coverage zone,

an image or video will still be captured every 15 minutes during the

2.5 hour block of time. If an animal triggers the camera “in between”

the 15 minute intervals, it will be recorded, same as it would if you

had setup the camera with Time Lapse turned Off. Note: Time Lapse

settings of frequent intervals and/or long periods between start

and stop time can reduce battery life.

15

Step 2-set Start Time

(Hour & Minute)

Step 3-set Stop Time

(Hour & Minute)

Step 4-set Interval

(60, 30, 15, 5 or 1 M)

Step 1-set Time Lapse

Mode to “On”

16

Parameter

Settings

(Bold=default)

Description

Mode

Camera or

Video

Selects whether still photos or video

clips are captured when the camera is

triggered.

Image Size

(only aects

still photos)

4M Pixel,

6M Pixel,

2M Pixel

Selects resolution for still photos from

2 to 6 megapixels. Higher resolution

produces better quality photos, but

creates larger ﬁles that take up more

of the SD card capacity (ﬁlls up faster).

The default 4M setting is a good

compromise between quality and ﬁle

size.

Capture

Number

(only aects

still photos)

1 Photo,

2 Photo,

3 Photo

Selects how many photos are taken

in sequence per trigger in Camera

mode. Please also refer to the Interval

parameter.

Video Size

(only aects

video clips)

High, Low

Selects video resolution (in pixels per

frame). High=720x400, Low=352x192

(both @30fps). Higher resolution

produces better quality videos, but

creates larger ﬁles that take up more of

the SD card capacity (ﬁlls up faster).

Video

Length (only

aects video

clips)

10S

(second)

default, with

60S to5S

possible

range

Sets length per captured video clip.

Settings begin with 10 second default

when parameter is ﬁrst selected. After

stepping down to 5S, video length

settings start over at 60S.

The SETUP Menu – Parameters and Settings List w/

Descriptions

17

Parameter

Settings

(Bold=default)

Description

Interval

10S

(second)

default,

with a 60M

(minute)

to1S

(second)

range of

settings

available.

(60M-1M

are set in

one minute

increments,

59S-1S

are set in

one second

increments)

Selects the length of time that the

camera will “wait” until it responds to

any additional triggers from the PIR

after an animal is ﬁrst detected and

remains within the sensor’s range.

During this user set “ignore triggers”

interval, the camera will not capture

photos/videos. This prevents the card

from ﬁlling up with too many redundant

images. Settings begin with 10 second

default when parameter is ﬁrst selected.

Note: after setting down past “1S”, settings

start over at “60M”.

Sensor Level

Normal,

Low, High

Selects the sensitivity of the PIR

sensor. The “High” setting will make

the camera more sensitive to infrared

(heat) and more easily triggered by

motion, and the “Low” setting makes it

less sensitive to heat and motion. The

High setting can be useful when the

ambient temperature is warm (making

it more difﬁcult for the sensor to detect

animals), and the Low setting may help

in cold weather if the camera is being

triggered too often by anything warmer

than the surroundings.

18

Parameter

Settings

(Bold=default)

Description

Format Execute

Deletes (erases) all ﬁles stored on a

card to prepare it for reuse. Always

format a card that has been previously

used in other devices. If no SD card is

inserted, all photos/videos in the inter-

nal memory will be deleted. Caution!

Make sure you have downloaded

and backed up any ﬁles you want to

preserve ﬁrst! Press OK to execute,

press MENU (or select NO then press

OK) to exit without formatting.

TV Out

NTSC, PAL

Selects video standard /format for

the “AV Out” output jack. The video

standard is NTSC for the United

States, Canada, Mexico, Asia and

South America. PAL is used primarily

in Europe.

Time Stamp

(only aects

still photos)

On, Off

Select “On” if you want the date & time

(that the photo was captured) imprinted

on every photo, select “Off” for no

imprint.

Set Clock Set

Press OK and use the UP/DOWN

keys (to change the setting) and LEFT/

RIGHT keys ( to move to the next

ﬁeld) to set the hour (24-hr format only,

“00”=midnight, “12”=noon) and minute,

and then (on the lower row), the year,

month and date. When ﬁnished, press

OK.

19

Parameter

Settings

(Bold=default)

Description

Time Lapse

On, Off Turns Time Lapse recording mode on/

off. Pressing OK after selecting On will

change to the Set Time Lapse screen,

which allows you to set the Start and

Stop times in hours (0-24) and minutes

(00-59).These set the times each day

that recording begins and ends (24

-hr clock, so 13:00 hours=1PM). Use

the RIGHT key to step through the

ﬁelds, and use UP/DOWN to change

the settings. After you set the “Stop”

minutes, the next press of the RIGHT

arrow key will jump to the screen for

setting the Interval (how often the Trail

Cam will "wake up" and record). You

can select 60, 30, 15, 5 or 1 minutes

(default is 5M).

Video Sound

(only affects

video clips)

On, Off Select “On” to record audio along with

the video when the camera is set to

video mode (saved ﬁle sizes will be

slightly larger).

Default Set

Cancel,

Execute

Select “Execute” and press OK to

restore all parameters to the original

factory default settings. If the camera is

behaving oddly and you think you may

have changed the setting for something

accidently (but aren’t sure which one),

this will reset all parameters to their

most commonly used or “generic”

settings.

20

MOUNTING AND POSITIONING

Mounting

After you’ve set up the camera’s parameters to your personal preferences

at home or in your truck, you’re ready to take it outside and slide the power

switch to “ON”. When setting up the Trail Cam for scouting game or other

outdoor applications, you must be sure to mount it in place correctly and

securely. We recommend mounting the Trail Cam on a sturdy tree with a

diameter of about 6 in. (15cm). To get the optimal picture quality, the tree

should be about 16-17 ft. (5 meters) away from the place to be monitored,

with the camera placed at a height of 5-6.5 ft. (1.5~2 m). Also, keep in mind

that you will get the best results at night when the subject is within the ideal

ﬂash range, no farther than 45’ (14m) and no closer than 10’ (3m) from the

camera.

There are two ways to mount the Trail Cam: using the provided adjustable

web belt, or the tripod socket.

• Using the adjustable web belt: Fig. 5 illustrates using the web belt

on the Trail Cam. Push one end of the belt through the two brackets

on the back of the Trail Cam. Thread one plastic buckle part onto

each end of the belt. Fasten the belt securely around the tree trunk by

clicking the buckle ends together after tightening the belt so there is

no slack left.

• Using the tripod socket: The camera is equipped with a socket on its

back to enable mounting on a photo tripod or any mounting accessories

with a standard1/4-20 thread.

Fig. 5: Attaching the Belt

La pagina sta caricando ...

Tasco 119422 Manuale utente

Tasco 119422 Manuale utente

in altre lingue

Documenti correlati

Altri documenti