veratron VMH 14 Manuale utente

B000856

VMH SERIES

VMH 14

USER MANUAL

rev. AA

EN

DE

IT

FR

ES

B000856

LANGUAGE PAGE

ENGLISH 3

DEUTSCH 21

ITALIANO 40

VMH SERIES

VMH 14

USER MANUAL

rev. AA

EN

DE

IT

FR

ES

CONTENT

B001225

CONTENT

Introduction 3

Packaging Content 3

The All-in-one Gauge 3

Contactless Configuration 3

Safety information 4

Safety during Installation 4

Safety After installation 5

Electrical Connections 5

Installation 6

Before the Assembly 6

Installation with Spinlock 7

Connection 8

Device Pinout 8

EasyLink Connection 8

Display layout 10

Display Sections 10

Alarm Display 10

Configuration 11

VMH 14 Configurator App 11

VMH 14 Configuration 12

Supported Configurations 14

Alarm Settings 14

Technical Data 15

Datasheet 15

Technical Drawings 16

Accessories 17

INTRODUCTION

B001225

INTRODUCTION

PACKAGING CONTENT

1x VMH 14

B001099

1x 52 mm Rubber

sealing gasket

A2C53194838

1x 52 mm Mounting

Spinlock

A2C52059471

1x Veratron card

B000101

1x

Safety manual

B000100

THE ALL-IN-ONE GAUGE

The VMH device can easily be configured to be

the instrument you need - thanks to its sun-

readable display embedded into a standard 52

mm instrument housing with the elegant VMH-

series look.

The EasyLink-Interface allows the device to

display a variety of different datatypes, received

from any VMH- or OceanLink master device.

The simple but effective graphic design presents

the data in a clear and intuitive form. In addition,

the round bar graph with the customizable range

and the alarm displays helps you to visually better

understand your data.

CONTACTLESS CONFIGURATION

Thanks to the contactless configuration you can

setup your all-in-one instrument with your

smartphone!

Launch the companion app and define your

settings through the user-friendly interface, then

simply hold your mobile device in proximity of the

VMH 14 device to transfer the configuration.

Thanks to the embedded passive antenna the

configuration can be done powerless!

SAFETY INFORMATION

B001225

SAFETY INFORMATION

WARNING

• No smoking! No open fire or heat sources!

• The product was developed, manufactured

and inspected according to the basic safety

requirements of EC Guidelines and state-of-

the-art technology.

• The instrument is designed for use in grounded

vehicles and machines as well as in pleasure

boats, including non-classified commercial

shipping.

• Use our product only as intended. Use of the

product for reasons other than its intended use

may lead to personal injury, property damage

or environmental damage. Before installation,

check the vehicle documentation for vehicle

type and any possible special features!

• Use the assembly plan to learn the location of

the fuel/hydraulic/compressed air and

electrical lines!

• Note possible modifications to the vehicle,

which must be considered during installation!

• To prevent personal injury, property damage or

environmental damage, basic knowledge of

motor vehicle/shipbuilding electronics and

mechanics is required.

• Make sure that the engine cannot start

unintentionally during installation!

• Modifications or manipulations to veratron

products can affect safety. Consequently, you

may not modify or manipulate the product!

• When removing/installing seats, covers, etc.,

ensure that lines are not damaged and plug-in

connections are not loosened!

• Note all data from other installed instruments

with volatile electronic memories.

SAFETY DURING INSTALLATION

• During installation, ensure that the product’s

components do not affect or limit vehicle

functions. Avoid damaging these components!

• Only install undamaged parts in a vehicle!

• During installation, ensure that the product

does not impair the field of vision and that it

cannot impact the driver’s or passenger’s head!

• A specialized technician should install the

product. If you install the product yourself,

wear appropriate work clothing. Do not wear

loose clothing, as it may get caught in moving

parts. Protect long hair with a hair net.

• When working on the on-board electronics, do

not wear metallic or conductive jewelry such as

necklaces, bracelets, rings, etc.

• If work on a running engine is required, exercise

extreme caution. Wear only appropriate work

clothing as you are at risk of personal injury,

resulting from being crushed or burned.

• Before beginning, disconnect the negative

terminal on the battery, otherwise you risk a

short circuit. If the vehicle is supplied by

auxiliary batteries, you must also disconnect

the negative terminals on these batteries!

Short circuits can cause fires, battery

explosions and damages to other electronic

systems. Please note that when you disconnect

the battery, all volatile electronic memories

lose their input values and must be

reprogrammed.

• If working on gasoline boat motors, let the

motor compartment fan run before beginning

work.

• Pay attention to how lines and cable harnesses

are laid so that you do not drill or saw through

them!

• Do not install the product in the mechanical

and electrical airbag area!

• Do not drill holes or ports in load-bearing or

stabilizing stays or tie bars!

• When working underneath the vehicle, secure

it according to the specifications from the

vehicle manufacturer.

• Note the necessary clearance behind the drill

hole or port at the installation location.

Required mounting depth: 65 mm.

SAFETY INFORMATION

B001225

• Drill small ports; enlarge and complete them, if

necessary, using taper milling tools, saber saws,

keyhole saws or files. Deburr edges. Follow the

safety instructions of the tool manufacturer.

• Use only insulated tools if work is necessary on

live parts.

• Use only the multimeter or diode test lamps

provided, to measure voltages and currents in

the vehicle/machine or boat. Use of

conventional test lamps can cause damage to

control units or other electronic systems.

• The electrical indicator outputs and cables

connected to them must be protected from

direct contact and damage. The cables in use

must have enough insulation and electric

strength and the contact points must be safe

from touch.

• Use appropriate measures to also protect the

electrically conductive parts on the connected

consumer from direct contact. Laying metallic,

uninsulated cables and contacts is prohibited.

SAFETY AFTER INSTALLATION

• Connect the ground cable tightly to the

negative terminal of the battery.

• Reenter/reprogram the volatile electronic

memory values.

• Check all functions.

• Use only clean water to clean the components.

Note the Ingress Protection (IP) ratings (IEC

60529).

ELECTRICAL CONNECTIONS

• Note cable cross-sectional area!

• Reducing the cable cross-sectional area leads

to higher current density, which can cause the

cable cross-sectional area in question to heat

up!

• When installing electrical cables, use the

provided cable ducts and harnesses; however,

do not run cables parallel to ignition cables or

to cables that lead to large electricity

consumers.

• Fasten cables with cable ties or adhesive tape.

Do not run cables over moving parts. Do not

attach cables to the steering column!

• Ensure that cables are not subject to tensile,

compressive or shearing forces.

• If cables are run through drill holes, protect

them using rubber sleeves or the like.

• Use only one cable stripper to strip the cable.

Adjust the stripper so that stranded wires are

not damaged or separated.

• Use only a soft soldering process or

commercially available crimp connector to

solder new cable connections!

• Make crimp connections with cable crimping

pliers only. Follow the safety instructions of the

tool manufacturer.

• Insulate exposed stranded wires to prevent

short circuits.

• Caution: Risk of short circuit if junctions are

faulty or cables are damaged.

• Short circuits in the vehicle network can cause

fires, battery explosions and damages to other

electronic systems. Consequently, all power

supply cable connections must be provided

with weldable connectors and be sufficiently

insulated.

• Ensure ground connections are sound.

• Faulty connections can cause short circuits.

Only connect cables according to the electrical

wiring diagram.

• If operating the instrument on power supply

units, note that the power supply unit must be

stabilized and it must comply with the following

standard: DIN EN 61000, Parts 6-1 to 6-4.

INSTALLATION

B001225

INSTALLATION

WARNING

Before beginning, disconnect the negative terminal on the battery, otherwise you risk a short circuit.

If the vehicle is supplied by auxiliary batteries, you must also disconnect the negative terminals on

these batteries! Short circuits can cause fires, battery explosions and damages to other electronic

systems. Please note that when you disconnect the battery, all volatile electronic memories lose their

input values and must be reprogrammed.

BEFORE THE ASSEMBLY

1.

Before beginning, turn off the ignition and

remove the ignition key. If necessary, remove

the main circuit switch.

Disconnect the negative terminal on the

battery. Make sure the battery cannot

unintentionally restart.

Refer to the safety instructions of this

document.

2.

Place the device at least 300 mm away from

any magnetic compass.

3.

Consider that the device must be connected

to an VMH master device and/or other VMH

14 gauges (maximum 16 gauges in a daisy

chain per master).

INSTALLATION

B001225

INSTALLATION WITH SPINLOCK

The panel width may be within a range of 1 to 12 mm. The drill hole must have a diameter of 52 mm [A].

WARNING

• Do not drill holes or ports in load-bearing or stabilizing stays or tie bars!

• Note the necessary clearance behind the drill hole or port at the installation location. Required

mounting depth: 40 mm.

• Drill small ports; enlarge and complete them, if necessary, using taper milling tools, saber saws,

keyhole saws or files. Deburr edges. Follow the safety instructions of the tool manufacturer.

1. Create a circular hole in the panel considering

the device dimensions. [A]

2. Remove the spinlock and insert the device

from the front. [B]

3. Adjust the spinlock as shown in picture [C]

according to the panel thickness.

4. Carefully screw in the spinlock by hand at

least two turns.

5. Insert the connector.

A B

C

CONNECTION

B001225

CONNECTION

DEVICE PINOUT

The VMH 14

device is designed with two AMP

SuperSeal 1.5 connectors on the backside – one male

and one female – to allow the daisy-chain connection

of up to 16 instruments in series to the master.

Wire color Description

Red + 12V power

Blue Ground

Yellow EasyLink data

EASYLINK CONNECTION

EasyLink connection with VMH 35 master

and two VMH 14 satellites

Once the panel installation is complete it is

possible to connect the VMH 14 to the EasyLink

interface.

The device can be directly connected to the

EasyLink master (like the VMH 35 display), or in

series to another VMH 14 satellite thanks to the

daisy-chain architecture.

NOTE: One master must always be present in the

system to distribute the data to the satellites.

Make sure the contacts have been locked audibly

into place so to preserve the water tightness.

CONNECTION

B001225

In case the length of the cable is not enough to reach the

next device, it is possible to extend the total length by using

the accessory EasyLink extension cable A2C59500139.

Please note that EasyLink does not allow daisy chains

longer than 20 meters and with maximum 16 satellite

devices.

It is recommended to connect the blind plug (provided with

the master instrument) after the last satellite instrument to

avoid water intrusion through the unused connector.

DISPLAY LAYOUT

B001225

DISPLAY LAYOUT

DISPLAY SECTIONS

A: Round Bar Graph

The bar graph helps to interpret the displayed vessel

information quicker and more intuitive. The minimum

and maximum values of the bar graph range are

customizable via the VMH14 App.

(Refer to the section Configurations to learn more about

the process of customizing and the limitations of the bar

graph ranges.)

B: Numeric Value

The big number in the middle represent the measured

value.

C: Unit

The unit of measurement is displayed right next to the

numeric measurement value.

D: Instance

For some data types it’s possible that there are several

different values available on the EasyLink bus.

The number in “area D” represents the instance number

of the value, currently displayed. This means, depending

on the data type, the engine number/ tank number/etc. .

E: Data Type Symbol

On the bottom of the display there is a symbol

representing the currently selected data type.

Refer to the section Configuration to see all displayable

values and their according symbols.

ALARM DISPLAY

The display can indicate that the received value has exceeded or fell below a certain threshold. If this is the

case, the bar graph and the numeric value will start to blink with a frequency of 1Hz.

More information about the alarm settings and how to configure them can be found in the section

“Configuration”.

CONFIGURATION

B001225

CONFIGURATION

VMH 14 CONFIGURATOR APP

To configure the VMH 14, some parameters must be calibrated, like which value to display, the range of the

bar graph and the alarms such as their thresholds.

This is possible through the smartphone App “VMH 14”, which can be downloaded free of charge from the

stores of both Android and iOS devices.

A simple and detailed explanation of the configuration process is also available as in-app instructions.

Thanks to the passive embedded NFC receiver, the VMH 14 can be configured, as described below, without

the need of a power supply.

VMH 14

CONFIGURATOR

The setup of the VMH 14 device is an intuitive three-step process. Please remember that you must READ

from the device before being able to modify and download the configuration to the instrument.

1. READ

2. CONFIGURE

3. WRITE

CONFIGURATION

B001225

VMH 14 CONFIGURATION

1.

READ THE

VMH 14

CONFIGURATION

Launch the “VMH 14” App and read the current

configuration of the device by “tapping” the

smartphone onto the NFC symbol on the

devices rear side.

The READ operation is mandatory before the

WRITE operation is allowed.

After the readout, the App will be set with the

current configuration.

NOTE: The antenna position on the

smartphone depends on the model.

Please refer to the smartphone manufacturer

manual.

2. SELECT GAUGE TYPE

Tap the “Data to display” item in the “Display

Settings” section to choose the data you want

to display on the VMH 14.

Note: See the complete list of supported gauge

types in the “Supported Configurations” table

of this document.

3. SET UNITS AND INSTANCE

Define the unit for the displayed value if more

than one is available (see “Supported

Configurations” table).

Set the instance for the displayed value (e.g.

Engine No. or Tank No.) so that the VMH 14 will

show your data on the display.

CONFIGURATION

B001225

4. BARGRAPH SETTINGS

It’s possible to customize the range of values,

which the bar graph should be able to reach.

In order to do so, just move the levers into the

desired position.

5. CONFIGURE THE ALARM

The alarm can be activated or deactivated by

using the switches on the right side of the

according alarm description.

Once active, it is possible to set a threshold for it

in the dedicated field.

The threshold unit is the same unit as defined in

step 3.

Note: the alarm threshold direction (active

above or active below) is statically defined (see

table “Alarm Settings”).

6. UPLOAD THE CONFIGURATION TO THE

VMH 14

Once the configuration is completed, you can

upload it to the VMH 14.

Press the “WRITE” button on the top/right of

the App screen and near the smartphone again

to the dedicated NFC area of the VMH device.

CONFIGURATION

B001225

SUPPORTED CONFIGURATIONS

Gauge Type Symbol Unit Bar Graph Range

Fuel Level

(Set as factory default)

%

0

–

100 %

Default: 0 – 100 %

Trim

TRIM

%

0

–

100 %

Default: 0 – 100 %

Coolant Temperature

°C

°F

0

–

200 °C

Default: 40 – 120 °C

Engine Oil Pressure

bar

PSI

0

–

30 bar

Default: 0 – 10 bar

Engine Oil Temperature

°C

°F

0

–

200 °C

Default: 0 - 150°C

Gear Oil Pressure

bar

PSI

0

–

30 bar

Default: 0 – 25 bar

Gear Oil Temperature

°C

°F

0

–

200 °C

Default: 0 – 150 °C

Voltmeter

-

V

0

–

30 V

Default: 11 – 14 V

*

The supported configurations may be updated at any time. Please make sure to always use the latest App

version.

ALARM SETTINGS

Gauge Type Alarm Description

Alarm

triggered...

Possible

Threshold Values

Fuel Level Low Fuel Level below threshold 0 - 100 %

Coolant Temperature

Engine

Overtemperature above threshold 0 - 200 °C

Engine Oil

Temperature

High Oil

Temperature above threshold 0 - 200 °C

Engine Oil Pressure Low Oil Pressure below threshold 0 - 30 bar

Gear Oil Temperature

High Gear Oil

Temperature above threshold 0 - 200 °C

Gear Oil Pressure Low Gear Oil Press below threshold 0 - 30 bar

Voltmeter

Battery Low below threshold 0 - 30 V

Overvoltage above threshold 0 - 30 V

Trim Engine Tilt above threshold 0 - 100 %

TECHNICAL DATA

B001225

TECHNICAL DATA

DATASHEET

Nominal Voltage 12 V (from EasyLink connection)

Connectivity EasyLink, NFC

Configuration interface NFC (Near Field Communication)

Protection class IP X7 acc. IEC60529

Display Optically bonded IBN segment display

Lens Mineral glass

Housing Ø52 mm – Polycarbonate (PC), flame retardant acc.

UL94-V0

Required mounting depth 40 mm

Bezels Brushed stainless steel

Operating temperature -20°C to +60°C

Storage temperature -30°C to +80°C

Connector

AMP SuperSeal 1.5

P/N Male: 282105-1

P/N Female: 282087-1

Mounting Spinlock Nut – locking height 0.5 – 20 mm

Certifications CE, UKCA, Reach, RoHS, UL94-V0

TECHNICAL DATA

B001225

TECHNICAL DRAWINGS

ACCESSORIES

B001225

ACCESSORIES

Accessory Part Number

EasyLink Extension cable A2C59500139

Spinlock Nut 52 mm A2C52059471

52 mm Rubber sealing gasket A2C53194838

Visit http://www.veratron.com

for the complete list of accessories.

veratron AG

Industriestrasse 18

9464 Rüthi,

Switzerland

T +41 71 7679 111

[email protected]

veratron.com

Any distribution, translation or reproduction, partial or total, of the

document is strictly prohibited unless with prior authorization in

writing from veratron AG, except for the following actions:

• Printing the document in its original format, totally or partially.

• Copying contents without any modifications and stating Veratron

AG as copyright owner.

Veratron AG reserves the right to make modifications or

improvements to the relative documentation without notice.

Requests for authorization, additional copies of this manual or

technical information on the latter, must be addressed to veratron

AG.

La pagina sta caricando ...

veratron VMH 14 Manuale utente

veratron VMH 14 Manuale utente

in altre lingue

Documenti correlati

Altri documenti