RODE Microphones M5MP Manuale utente

1

www.rodemic.com/m5

M5

ENGLISHINSTRUCTION MANUAL

Compact 1/2”

Cardioid Condenser

Microphones

M5_multilingual_manual.indb 1M5_multilingual_manual.indb 1 2/09/2013 6:59:47 PM2/09/2013 6:59:47 PM

2

The M5 is a studio quality half-inch condenser microphone,

designed for highly detailed sound reproduction. It features a

cardioid polar pattern and end address design, meaning that it will

pick up sound directed into the end of the microphone, and reject

sound from the rear of the mic.

This pickup pattern allows for recording of the desired sound

source while reducing the level of other surrounding instruments,

noises or sound sources.

The M5 is not only ideal for recording music, but is a fantastic

microphone for environmental recordings and indoor dialogue on

ﬁ lm sets.

The enclosed pair has been hand-picked by RØDE’s audio

engineering team to be acoustically matched to ensure perfect

compatibility when used in stereo conﬁ gurations.

Introduction

M5_multilingual_manual.indb 2M5_multilingual_manual.indb 2 2/09/2013 7:00:05 PM2/09/2013 7:00:05 PM

3

Features

• ½” capsule with gold-plated membrane

• Cardioid polar pattern

• All metal body

• Ultra-low noise transformerless circuitry

• State-of-the-art surface mount electronics

• Heavy-duty matte black ﬁ nish

• Gold plated output connectors

• Designed & manufactured in Australia

• Free 10 year extended warranty when you register online at

www.rodemic.com/warranty

M5_multilingual_manual.indb 3M5_multilingual_manual.indb 3 2/09/2013 7:00:05 PM2/09/2013 7:00:05 PM

4

The M5 is covered by a limited warranty for one (1) year from the

date of purchase. This can be extended free of charge to a full

ten (10) year warranty by registering your microphone online at

visiting our website as below.

Warranty

Register your M5 pair now and

validate your free 10 year warranty.

Scan the QR code with a smartphone,

or visit www.rodemic.com/warranty

M5_multilingual_manual.indb 4M5_multilingual_manual.indb 4 2/09/2013 7:00:05 PM2/09/2013 7:00:05 PM

5

Speciﬁ cations

Polar Response

Frequency

Response

0˚

90˚ 270˚

180˚

-2.0

-20.0

-10.0

0.0

-2.0

-4.0

-6.0

-8.0

-10.0

-12.0

-14.0

-16.0

-18.0

-20.0

-22.0

-24.0 -25.0

dB rel. 1V/Pa

+5.0

Frequency:

500 Hz:

1000 Hz:

4000 Hz:

M5_multilingual_manual.indb 5M5_multilingual_manual.indb 5 2/09/2013 7:00:05 PM2/09/2013 7:00:05 PM

6

Acoustic Principle Pressure Gradient

Active Electronics JFET impedance converter with bipolar

output buffer

Directional Pattern Cardioid

Frequency Range 20Hz ~ 20kHz

Output Impedence 200Ω

Equivalent Noise 19 dBA SPL (as per IEC651)

Maximum Output +13.5 dBu (1KHz, 1% THD into 1K Ω load)

Sensitivity -34 dB re 1V/Pa

(10.46mV @ 94dB SPL)

± 2dB @ 1kHz

Dynamic Range 121 dB SPL

Speciﬁ cations

M5_multilingual_manual.indb 6M5_multilingual_manual.indb 6 2/09/2013 7:00:05 PM2/09/2013 7:00:05 PM

7

Maximum SPL 140 dB SPL

Signal / Noise 75 dBA SPL (as per IEC651)

Power Requirements 24V phantom power

48V phantom power

Output Connection 3 Pin XLR

Balanced output between pin 2 (+),

pin 3 (-) and pin 1 (ground)

Net Weight 80g

Accessories RM5 mic clip (x2)

WS5 windshield (x2)

M5_multilingual_manual.indb 7M5_multilingual_manual.indb 7 2/09/2013 7:00:06 PM2/09/2013 7:00:06 PM

8Powering the M5

Connect all cables before supplying phantom power to the

microphone(s) and never remove the microphone cable while the

power is connected.

The M5 requires 48V DC (P48) or 24V DC (P24) phantom power.

If the mixer or preamp does not contain this phantom power

requirement, then an external phantom power supply is needed.

Some phantom power supplies do not supply the voltage at

which they are rated. If the required voltage is not supplied, the

dynamic range and general performance of the microphone will

be reduced.

We strongly suggest the use of a reputable high quality power

supply. Damage caused by a faulty power supply is not covered

under warranty.

M5_multilingual_manual.indb 8M5_multilingual_manual.indb 8 2/09/2013 7:00:06 PM2/09/2013 7:00:06 PM

What is Phantom Power?

All condenser microphones require a power source to operate the

internal circuitry of the microphone.

Phantom power is a DC voltage, supplied to the microphone

through the XLR cable, providing the microphone circuit with the

power it requires to operate, without the need for an external

microphone power supply.

Most mixing desks, audio interfaces, and preamp units have a

phantom power switch inbuilt. If your equipment doesn’t have a

phantom power supply, an external one can be purchased and

used in-line between the preamp and the M5. Be sure to check

that your phantom power supply is either P48 (48V DC) or P24 (24V

DC) to operate the correctly.

M5_multilingual_manual.indb 9M5_multilingual_manual.indb 9 2/09/2013 7:00:06 PM2/09/2013 7:00:06 PM

10 Mounting the M5

The M5 matched pair is supplied with a pair of RM5 stand mounts.

These feature a standard 5/8” thread in the base and a 3/8” thread

adaptor is supplied to provide even greater versatility in mounting.

To mount the M5 in the RM5 place the base of the microphone

at the back of the mount and ﬁ rmly push down towards the front

until the microphone clicks into the mount.

The tension of the RM5 can be adjusted using the lever on the side

of the mount.

M5_multilingual_manual.indb 10M5_multilingual_manual.indb 10 2/09/2013 7:00:06 PM2/09/2013 7:00:06 PM

11

The M5 is an ‘end-address’ microphone, and so the mesh head

should always be facing towards the sound source that you wish

to record.

When recording any sound source, whether it be vocals,

instruments or anything else, always spend time experimenting

with mic placement to ensure you are picking up the best possible

sound. Adjust the microphone position as many times as you need

to achieve this, rather than attempting to compensate with EQ and

other processing tools later on.

If you are recording through an interface, channel strip or mixing

desk with an inbuilt EQ section, always begin by setting the EQ

ﬂ at (no cut or boost) or turn it off if possible. Once the preferred

sound has been achieved through mic placement, any processing

such as EQ, compression, reverb and other effects can be added

to enhance the sound of your recording.

EQ is always best used sparingly, and when attempting to change

the sound of a recording in any way you should always start by

‘cutting’ any unwanted frequencies, rather than boosting the other

frequencies.

General Operation

M5_multilingual_manual.indb 11M5_multilingual_manual.indb 11 2/09/2013 7:00:06 PM2/09/2013 7:00:06 PM

12 General Operation

As with other aspects of the recording process, ﬁ nding the right

sound is always a matter of experimentation, and you should

always go with whatever sounds best to you. Listen with your ears,

not with your eyes!

M5_multilingual_manual.indb 12M5_multilingual_manual.indb 12 2/09/2013 7:00:06 PM2/09/2013 7:00:06 PM

13

Whether using them as a single microphone or stereo pair,

there are no set rules when it comes to placement for your

M5 microphones, but the tips below are a great starting point

to achieve great results in most scenarios. Don’t be afraid to

experiment with your own mic placements to produce the sound

that you’d like to pick up with your M5.

Microphone Placement

Scan the code with your

smartphone or visit

rockro.de/m5stereo to

watch a video showing stereo

applications for the M5

M5_multilingual_manual.indb 13M5_multilingual_manual.indb 13 2/09/2013 7:00:06 PM2/09/2013 7:00:06 PM

14

Stereo spaced pair

To mount your M5 microphones in a spaced pair conﬁ guration,

you’ll need to place your microphones on two separate

microphone stands. It is best to experiment with the exact

positioning and direction of the microphones while listening to the

signal, to ensure phase compatibility.

The Spaced pair is ideal for recording sound sources

or instruments that cover a wider area, or require more

than one point-source to pick up a true representation

of the sound.

It will generally produce a very wide stereo image, and

is great for recording sound sources such as choirs and

ensembles, but can also produce incredible results on

individual instruments when used correctly.

Microphone Placement

M5_multilingual_manual.indb 14M5_multilingual_manual.indb 14 2/09/2013 7:00:06 PM2/09/2013 7:00:06 PM

15

Sound Source

M5_multilingual_manual.indb 15M5_multilingual_manual.indb 15 2/09/2013 7:00:06 PM2/09/2013 7:00:06 PM

16

Stereo X-Y

To mount your M5 pair in X/Y conﬁ guration, place the microphones

either on a stereo bar, or on two separate microphone stands. The

microphones should be placed at 90º to one another (right angle)

with the capsules stacked above each other vertically.

X/Y conﬁ guration is a coincident stereo technique that can

be used to pick up sound sources in stereo with maximum

phase coherency, meaning that the sounds you record will

not only sound great in stereo, but they will also sound

great when played back in mono.

This is achieved by having the capsules placed right above

one another, as close as possible on the vertical axis,

so that sound reaches both capsules at the same time.

While X/Y conﬁ guration is great for mono compatibility and

ease of use, the stereo image will not be as wide as other

techniques such as ORTF or a spaced pair conﬁ guration.

Microphone Placement

M5_multilingual_manual.indb 16M5_multilingual_manual.indb 16 2/09/2013 7:00:06 PM2/09/2013 7:00:06 PM

17

90°

Sound Source

M5_multilingual_manual.indb 17M5_multilingual_manual.indb 17 2/09/2013 7:00:06 PM2/09/2013 7:00:06 PM

18

Stereo ORTF

To mount your M5 pair in ORTF conﬁ guration, place the

microphones either on a stereo bar, or on two separate

microphone stands. The microphones should be placed at 110º to

one another with the capsules 17cm apart and facing outward.

The ORTF technique was devised around 1960 by a French

broadcast station, the Ofﬁ ce de Radiodiffusion Télévision

Française, and was originally designed to mimic the

response of human hearing.

The increased distance between the capsules will produce

a wider stereo image than coincident stereo miking

techniques like X/Y or Mid-side.

Microphone Placement

M5_multilingual_manual.indb 18M5_multilingual_manual.indb 18 2/09/2013 7:00:06 PM2/09/2013 7:00:06 PM

19

17cm

110°

Sound Source

M5_multilingual_manual.indb 19M5_multilingual_manual.indb 19 2/09/2013 7:00:06 PM2/09/2013 7:00:06 PM

20

After use the M5(s) should be removed from its mount, wiped with

a dry, soft cloth and placed into storage.

Be sure to place the moisture-absorbent crystals (supplied) at

the head of the microphone when in storage, so as to absorb any

moisture present. Eventually this pack of crystals will need to be

dried. This is indicated by the crystals turning pink in colour.

They can easily be re-used by placing them in an oven at 100 – 150

degrees Celsius for approximately ten minutes. The crystals will

operate effectively again once they have turned blue.

Safety and maintenance

M5_multilingual_manual.indb 20M5_multilingual_manual.indb 20 2/09/2013 7:00:06 PM2/09/2013 7:00:06 PM

La pagina sta caricando ...

RODE Microphones M5MP Manuale utente

Questo manuale è adatto anche per

RODE Microphones M5MP Manuale utente

in altre lingue

Documenti correlati

Altri documenti