MULTIPLEX EasyStar Building Instructions

Marca: MULTIPLEX

Modello: EasyStar

Categoria: Giocattoli telecomandati

Tipo: Building Instructions

Bauanleitung

Notice de construction

Building instructions

Instruzioni di montaggio

Instrucciones de montaje

BK + Permax 400/6V # 21 4192

RTF-Modell # 1 3200

Sicherheitshinweise

- Prüfen Sie vor jedem Start den festen Sitz des Motors und der Luftschrauben - insbesondere nach dem Transport, härteren

Landungen sowie Abstürzen. Prüfen Sie ebenfalls vor jedem Start den festen Sitz und die richtige Position der Tragflächen auf dem

Rumpf.

- Akku erst einstecken, wenn Ihr Sender eingeschaltet ist und Sie sicher sind, daß das Bedienelement für die Motorsteuerung auf

"AUS" steht.

- Im startbereiten Zustand nicht in den Bereich der Luftschraube greifen.

Vorsicht in der Luftschraubendrehebene - auch Zuschauer zur Seite bitten!

- Zwischen den Flügen die Motortemperatur durch vorsichtige Fingerprobe prüfen und

vor einem Neustart den Motor ausreichend abkühlen lassen. Die Temperatur ist richtig, wenn Sie den Motor problemlos berühren

können. Insbesondere bei hohen Außentemperaturen kann dieses bis zu 15 Minuten dauern.

- Denken Sie immer daran: Niemals auf Personen und Tiere zufliegen.

Conseils de sécurité

- Avant chaque décollage, vérifiez la fixation du moteur et de l'hélice, notamment après le transport, après les atterrissages violents

et après un “Crash”. Vérifiez également, avant chaque décollage la fixation ainsi que le positionnement de l’aile par rapport au

fuselage.

- Ne branchez l’accu de propulsion que si vous êtes sûr que votre émetteur est allumé et que l’élément de commande moteur est en

position “ARRET”.

- Ne mettez pas vos doigts dans l’hélice! Attention à la mise en marche, demandez également aux spectateurs de reculer.

- Entre deux vols, vérifiez en posant un doigt dessus, la température du moteur, laissezle refroidir suffisamment avant le prochain

décollage. La température est correcte si vous pouvez maintenir votre doigt ou votre main sur le moteur. Le temps de refroidissement

peut varier jusqu’à 15 minutes s’il fait particulièrement chaud.

- Pensez-y toujours: ne volez jamais vers ou au-dessus des personnes ou des animaux.

Safety notes

- Before every flight check that the motor and propeller are in place and secure - especially after transporting the model, and after

hard landings and crashes. Check also that the wing is correctly located and firmly secured on the fuselage before each flight.

- Don’t plug in the battery until you have switched on the transmitter, and you are sure that the motor control on the transmitter is set

to “OFF”.

- When the model is switched on, ready to fly, take care not to touch the propeller. Keep well clear of the propeller disc too, and ask

spectators to stay back.

- Allow the motor to cool down after each flight. You can check this by carefully touching the motor case with your finger. The

temperature is correct when you can hold your finger on the case without any problem. On hot days this may take up to 15 minutes.

- Please keep in mind at all times: don’t fly towards people or animals.

Note di sicurezza

- Prima di ogni decollo controllare che il motore e la eliche siano fissati stabilmente - specialmente dopo il trasporto, atterraggi duri

e se il modello è precipitato. Controllare prima del decollo anche il fissaggio e la posizione corretta delle ali sulla fusoliera.

- Collegare la batteria solo quando la radio è inserita ed il comando del motore è sicuramente in posizione ”SPENTO”.

- Prima del decollo non avvicinarsi al campo di rotazione della eliche. Attenzione alla eliche in movimento - pregare che eventuali

spettatori si portino alla dovuta distanza di sicurezza!

- Tra un volo e l’altro controllare cautamente con le dita la temperatura del motore e farli raffreddare sufficientemente prima di ogni

nuovo decollo. La temperatura è giusta se si possono toccare senza problemi. Specialmente con una temperatura esterna alta

questo può durare fino a 15 minuti.

- Fare attenzione: Non volare mai nella direzione di persone ed animali.

Advertencias de seguridad

- Compruebe antes de cada despegue que el motor y la hélice estén fuertemente sujetados, sobretodo después de haberlo transportado,

de aterrizajes más fuertes así como después de una caída. Compruebe igualmente antes de cada despegue que las alas estén bien

sujetas y bien colocadas en el fuselaje.

- Conectar la batería, cuando la emisora esté encendida y Usted esté seguro que el elemento de mando para el motor esté en ”OFF”.

- No meter la mano en la zona inmediata a la hélice cuando el avión esté a punto de despegar. ¡Cuidado con la zona de la hélice!

¡Pedir a los espectadores que se aparten!

- Entre los vuelos hay que comprobar cuidadosamente la temperatura del motor con el dedo y dejar que el motor se enfríe antes de

volver a despegar. La temperatura es correcta, si puede tocar el motor sin problemas. Sobretodo en el caso de temperaturas del

ambiente muy altas, esto puede tardar unos 15 minutos.

- Recuerde: No volar nunca hacía personas o animales.

# 21 4192

Familiarise yourself with the kit!

MULTIPLEX model kits are subject to continuous material monitoring during production. We hope that you will be

happy with the contents of the model kit. However, we ask you to check all parts (against the parts list) before

using them, as processed parts are non exchangeable. If a part should not function, we will be happy, after

checking the problem, to repair or replace the part. In such a case, please send the part to our model construction

department and do not forget to enclose proof of purchase and a short description of the fault.

We are continuously working on the technical improvement of our models. We reserve the right to modify the

contents of the kit with regard to shape, size, technology, material and features at any time and without notification.

Please understand that information and figures in these instructions cannot form the basis for a legal claim.

Warning!

Remotely controlled models, in particular aircraft models, are not toys in the conventional sense. Their

construction and operation requires technical understanding, at least some practical ability and care as

well as discipline and self-confidence. Faults and carelessness during construction and operation can

result in injury to people and damage to property. Because the manufacturer has no influence over the

correct assembly, maintenance and operation we expressly draw these hazards to your attention.

Additional Products Required for Assembly :

Remote control system

When ordering in North and South America add an “M” in front of the part number

MULTIPLEX receiver PiCO 5/6 UNI 35 MHz A order no. 5 5920

40 MHz A order no. 5 5921

72 MHz order no. 5 5954

or MULTIPLEX receiver Micro IPD UNI 35 MHz A order no. 5 5971

40 MHz A order no. 5 5972

72 MHz order no. 5 5973

MULTIPLEX Servo Tiny S UNI (required 2 x) elevator / rudder order no. 6 5121

MULTIPLEX PiCO- 400 round UNI motor controller order no. 7 2292

Drive Battery:

MULTIPLEX drive battery NiCd 6 / 500 mAh order no. 15 5545

or MULTIPLEX drive battery Permabatt NiMh 6 / 1500 mAh order no. 15 6019

or MULTIPLEX drive battery NiCd 7 / 500 mAh order no. 15 5648

Charging unit:

MULTIcharger 4010 DC order no. 9 2527

Glue:

MULTIPLEX „Zacki leicht verdickt“ order no. 59 2720

MULTIPLEX “Zacki Aktivator” order no. 59 2824

Alternatively, a similar superglue (cyanoacrylate glue) can be used, but do not use a superglue for polystyrene.

Epoxy glues initially provide reasonable adhesion, but if loaded, the hard glue will crack off. The adhesion is

only superficial.

Tools: Scissors, craft knife, combination pliers, Ø 4-5 mm spike or small round file

Technical data:

wingspan 1370 mm

total length 917 mm

fuselage length 870 mm

weight during flight400 motor series / 6 AA cells approx. 680 g

wing size approx. 24 dm²

wing load approx. 28 g/dm²

RC functions rudder, elevator and motor control

Note: Remove the pages with the illustrations from the middle of the instructions for assembly!

Important information

This model is not made from polystyrene foam. For this reason it is not possible to use white glue or

epoxy glue. Please only use a cyanoacrylate glue, preferably one which is used in conjunction with an

activator (kicker). Please use a cyanoacrylate glue (superglue) of medium viscosity such as „ZACKi leicht

verdickt“ With Elapor®, always spray one side with the activator (kicker) – leave it to dry and cover the

other side with the cyanoacrylate glue (ZACKi). Join the parts together and fix their position immediately.

Take care when working with cyanoacrylate glues.

These glues harden within seconds. Therefore do

not touch with the fingers or allow contact to other

parts of the body. Wear protective goggles to protect

the eyes! Keep out of the reach of children!

1. Before assembly

Check the contents of the construction kit.

Fig. 1+2 and the parts list will help you with this.

RTF* : Parts marked like this are not part of the

EasyStar # 214192 construction kit!

RTF = Ready To Fly!

2. Assembly of fuselage and motor

Start with the left-hand side of the fuselage 3. A suitable

glue for all connections is a CA glue in conjunction with

an activator. Fig. 3

The enclosed motor 41 is already fitted with an

interference suppressor – this is adequate if the PiCO-

Control 400 round UNI # 7 2292 control is used. Solder

the controller # 7 2292 to the connection tags at the

motor. Even at this stage ensure that the motor runs

clockwise (when looking at the motor shaft / if it does

not, swap over the motor tags).

Glue the motor 41 into the half of the fuselage 3, making

it protrude by approx. 3 mm as is illustrated in fig. 4.

Ensure that no glue gets into the motor or covers the

cooling vents!

Now lay the cables to the drive battery and the receiver

at the front in the corresponding grooves in the half of

the fuselage 3. The cable must be entirely covered by

the foam. Fig. 3

If you intend to use a different controller, you should

improve the motor interference suppressor in order to

be on the safe side. For this purpose, a suitable

suppressor set # 8 5020 is available. If doing this, solder

on a 47 nF capacitor between the motor connection

and the motor housing and another, also of 47 nF,

between the motor connections.

Now the two halves of the fuselage 3 and 4 are glued to

each other – test first without the glue that this is possible

without difficulty – if necessary, correct any problems

first. Cover the gluing point on the half of the fuselage 3

with viscous glue (cyanoacrylate) – fuselage half 4 must

already have been spayed with activator and allowed

to dry – now carefully join parts 3 and 4 and align them!

The fuselage joint must be straight and must not be

bent! Fig. 5

3. Installation of the canopy lock

Install locking plates 22 for the fasteners for the canopy

lock so that the locking pin 23 can later lock between

plate 22 and the fuselage wall. To do this, spray the

„nests“ in the fuselage with the activator and allow to

dry. Then cover the locking plates with superglue and

insert without delay in the correct position. If necessary,

improve the glued connection later. Fig. 6

4. Attaching the rudder horns and connections for

the linkage to the elevator and the rudder

Shorten the T-shaped part of one of the rudder horns

24 to 2.5 mm as shown in fig. 8. Insert the linkage

connections 25 into the outer holes in the rudder horns

24 and fasten them using washer 26 and nut 27.

Warning: Observe the direction of installation, 1x left-

hand direction, 1x right-hand direction. Tighten the nuts

(but do not over-tighten them) and then secure them

with a spot (needle) of superglue. Pre-install the

hexagon-socket worm screw 28 in the linkage

connection 25 using the Allan key 29. Fig. 8+9

Glue the rudder horns 24 into the nests in the rudders

10 and 11 which have already been wetted with activator

– with the row of holes pointing towards the hinge line.

Fig. 8+9

5. Gluing in the elevator and the rudder

The elevator 10 and the rudder 11 are glued together

at a 90° angle. Please check this, for example by means

of a set-square. Fig. 10

6. Gluing the rudder and the elevator to the fuselage

Test-fit the elevator and the rudder, without using glue,

to the fuselage and check the fit. Observe in particular

whether the elevator 10 lies flush in the fuselage and is

parallel to the wing seat on the front of the fuselage.

Fig. 11

To do this, the spar connector 34 is placed across the

wing seat as an aid. Now look from the nose of the

fuselage over the spar connector and align the elevator

in this way. After aligning the elevator and the rudder in

the way described, glue them to the fuselage – check

the alignment again and make sure that there are no

gaps!

7. Installation of the servo motors into the fuselage

Using the remote control, switch the servo motors to

„neutral“ and mount the servo motor control hornss on

the motor in such a way that in the neutral position they

stick out at the sides at a 90° angle – 1x on the left-

hand side, 1x on the right-hand side. Now test-fit the

servo motors into the fuselage. Depending on the servo

motor type used, some small adaptations may be

necessary. Press out the holes for the servo motor

cables using the round file or a spike and pull the cables

into the fuselage. Shrink-fit the servo motors into the

shrink installation hose or wrap them with adhesive tape

and then glue in. Note: Never omit the adhesive tape

or the shrink hose. Otherwise glue might get into the

servo motor and destroy it. Fig. 12

8. Rudder linkage installation into the fuselage

The rudder linkage for the elevator and the rudder

consists of the external sleeve for the Bowden pull wire

31, the internal Bowden pull wire sleeve 33 and the steel

wire with Z-bend 30. These are fitted together and

hooked using the Z-bend to the servo motor lever fig.

13. The distance to the fulcrum from the servo motor

lever should be approx. 10 mm.

The other ends of the steel wires 30 are pushed through

the transverse holes for the linkage connectors 25.

Embed the Bowden pull wires into the fuselage and fix

the shorter external sleeve 31 as shown in fig. 13 - fig.

16. If necessary, the steel wire 30 is bent with pliers at

the rudder horn fig. 16. The external Bowden pull wire

sleeves 31 are now adhered to the fuselage along their

entire length. This much increases the stability of the

rudder support. Ensure that the Bowden pull wires run

easily and that no glue can enter into the Bowden pull

wire sleeve. Finally, the servo motors are set to the

neutral position and the hexagon-socket worm screws

28 are tightened at the linkage connections 25.

9. Antenna installation to the bottom of the fuselage

The connection to the antenna for the receiver is led to

the bottom of the fuselage and inserted into the plastic

tube 32.

For this, a hole must be pierced from the beginning of

the groove along the bottom of the groove to the inside

of the fuselage, then push the antenna through from

the inside and insert into the tube 32. This is most easily

done with a pointed steel wire. It is then pushed along

tube 32 and stuck into the end of the antenna insulation.

It may be helpful to secure the end with a spot of

superglue. At the end of the fuselage, the antenna tube

is inserted into the spike and secured along its entire

length by means of adhesive tape. Warning: Do not bend

the fuselage while doing this.

Fig. 17

10. Gluing in the locking pin for the canopy

Pairs of locking pins 23 are inserted into the canopy 5.

The pins should point towards the inside! Apply “ZACKi

leicht verdickt” to the toothed part, but without activator!

Then insert half of the locking pins into the slots of the

canopy. Immediately allow the canopy to be locked by

the locking pins in the locking plates 22 and then align

without delay. Wait for approx. 1 minute and then open

the canopy carefully. Spray activator onto the gluing

points of the locking pins. Fig. 18

11. Attaching the propeller

Detach the propeller from the (black) spinner, turn over

the propeller (the embossed writing will now point to

the rear) and then re-insert the spinner. Pierce the

spinner with a needle from the rear to the front. This

allows the air to escape during the later installation. The

propeller is then glued onto the motor shaft using 5-

minute-resin or using Endfest 300 (UHU). Fig. 19

Do not use superglue here!!! It may cause the

material to become brittle and shatter then the

spinner will detach!

12. Inserting the wings

The spar covers 8 and 9 must be carefully glued into

the wings 6 and 7. Take care not to allow any glue to

touch the surfaces which will later be inserted into the

spar connectors 34. First try out the spar connectors

34, when you are certain that there is no active glue

inside the hole, the spar is to be inserted. Otherwise it

might happen that you will be unable to ever dismantle

the model again. Fig. 20

13. Checking the plug-in connection

Now assemble the model by means of the spar

connector 34. When doing this, check the correct

attachment of the wings 6 + 7 in the fuselage. If

necessary re-work carefully. Fig. 21

14. Installing flight battery and receiver

The installation of the flight battery and the receiver is

as follows: The flight battery is located in the front of

fuselage nose, and behind it is the receiver. While

positioning these elements, pay attention to the location

at which the center of gravity should eventually lie

according to point 17. Glue the Velcro tape (knobbly

side) to the positions on the fuselage floor where the

flight battery and the receiver are to be installed. The

adhesive backing of the Velcro tape is not sufficient for

this purpose; use additional superglue.

The final position of the flight battery is determined when

the center of gravity is determined. Ensure that the

Velcro tape makes good contact with the battery . If you

are not working carefully here, you might lose your

battery in-flight.

Each time before take-off check that the battery is

securely attached!

Test-install all the connections following the instructions

for the remote control.

Insert the battery / motor controller connection plug

only after switching on your transmitter and if you

are certain that the transmitter throttle control is

set to the off position.

Insert the servo motor plug into the receiver. Switch on

the transmitter and connect the drive battery to the

controller and the controller to the receiver. Your

controller must be equipped with a battery eliminator

circuit (BEC,this powers the receiver and servos directly

from the flight battery.).

Now briefly switch the motor on and re-check the

direction of rotation of the propeller. (Hold the model

firmly during the test run, remove loose, light objects

from behind the model.)

Caution, even with small motors and propellers there

is the danger of injury!

15. Adjustment of the elevator and the rudder

movement

In order to make the model follow commands smoothly,

the travel of the rudder and elevator movement must

be adjusted correctly.

The elevator upwards (pull control stick ) approx. 5

mm and downwards (push control stick) approx. 4

mm. The rudder 10 mm to both the left-hand side

and the right-hand side; measure at the lowest point

of the rudder on either side.

Fig. 22

5mm

78mm

If your remote control does not allow this movement,

you will have to adjust your linkage connector.

16. Decoration

For decoration, a multi-color decoration sheet 2 is

enclosed. The individual words and symbols are cut out

and applied either according to our suggestion (picture

on the construction kit) or according to your own ideas.

Blacken the canopy 5 to its edge using a water-proof

felt tip pen.

17. Finding the center of gravity

In order to achieve stable flying characteristics, your

EasyStar must balance at one particular point, just like

any other aircraft. Set up your model so that it is ready

to fly and insert the fight battery .

The center of gravity is marked and then adjusted

to approx. 5mm in front of the rear edge of the spar

cover. This adjustment is equivalent to approx. 78

mm behind the front edge of the wing if measured

at the fuselage. If it is supported at this point by your

fingers, the model should balance horizontally.

Corrections are possible by shifting the fight battery .

Once the correct position is found, make a mark inside

the fuselage so that the battery can always be located

in the same position. Fig. 22

18. Preparation for the first flight

Wait for a calm day for the first flight. Often the evening

hours are particularly favourable.

Before the first flight, do a radio range check!

A range check will confirm that your radio system is

working properly. Transmitter batteries and flight

batteries must be freshly charged up and in accordance

with the instructions. Check

before switching on the

transmitter, that the channel to be used is available and

not being used by another modeler. .

A helper walks away with the transmitter with the

antenna completely pushed down.

While the helper is walking away, activate a control

function. Observe the servo motors. The non-activated

servo motor should remain still up to a distance of

approx. 35 m or 100 feet and the controlled one must

follow the control movements without delay. This test

can only be carried out successfully when the radio

channel is free of interference. This test must be

repeated while the motor is running. This should lead

to no more than a minor reduction in the reach.

If you are in any doubt, do not fly the aircraft. Have the

system checked by a knowledgable modeler or a radio

service facility. Hand the entire system (with drive

battery, switch cable, servo motors) to the service

department of the manufacturer of these appliances for

checking.

First flight ....

Do not attempt to launch your Easy Star without the

motor running !

The model is launched with a gentle toss into the wind.

During the first flight it is best to have the support

of an experienced helper.

This is the most important advice in this entire instruction

manual. If at all possible have an experienced R/C pilot

put the first flight on your new model. They will trim your

Easy Star so that it will fly “hands off” allowing you to

learn to fly with a stable, controllable airplane. If this is

not possible, double check to make sure all your controls

function correctly and in the proper direction. While

holding the model with the wings level at shoulder height,

turn on the motor to full power and gently toss the plane

into the wind. Your model should climb out and directly

away from you at a shallow angle with the wings level.

Resist the urge to “over control” the model with large

control stick movements, After a safe height has been

reached, adjust the rudder and the elevator with the

trims on your transmitter, so that the model flies straight

and wings level.

At a sufficient height, familiarise yourself with the

reaction of the model when the motor is switched off .

Simulate landing approaches at high altitude, so that

you are prepared when the drive battery runs low.

At the beginning, do not try any forced turns close to

the ground in during the landing procedure.

Land safely. It is better to walk some distance to retrieve

your plane than to risk crashing the model.

19. Safety

Safety is the most important rule during flying aircraft

models. It is suggested you obtain liability insurance

through the Modeling Association in your Country. If

you join a club or association you will be able to join an

insurance program there. Take care to be adequately

insured (for model aircraft with motor).

Always maintain the model and remote control in good

working condition. Find out about the charging

technology available for the batteries you use. Make

use of all the sensible safety equipment that you are

offered. Get information from our main catalogue;

MULTIPLEX products have been constructed by model

aircraft pilots from their practical experience for practical

use.

Fly conscientiously! To fly closely above the heads of

other people is not a sign of ability. Real experts do not

need to show off in this way. Point this out to other pilots

for our common interest. . Always fly in such a way that

neither you nor others are endangered. Always

remember that even the best remote control can be

disturbed by external influences. Even many years of

flying without an accident are no guarantee for the next

minute of flying.

We, the MULTIPLEX team, wish you fun and success

with the construction and flying of your Easy Star.

MULTIPLEX Modellsport GmbH &Co. KG

Product care and development

Klaus Michler

Parts list BK # 21 4192

Serial pce Designation Material Dimensions

1 1 construction instructions A4

2 1 decoration sheet printed adhesive film 350 x 500 mm

3 1 left-hand side fuselage half foam Elapor complete part

4 1 right-hand side fuselage half foam Elapor complete part

5 1 canopy foam Elapor complete part

6 1 left-hand wing foam Elapor complete part

7 1 right-hand wing foam Elapor complete part

8 1 left-hand spar cover foam Elapor complete part

9 1 right-hand spar cover foam Elapor complete part

10 1 elevator foam Elapor complete part

11 1 rudder foam Elapor complete part

Small parts

20 3 Velcro knobs plastic 25 x 60 mm

21 3 Velcro loops plastic 25 x 60 mm

22 2 locking plate injection-molded plastic complete part

23 2 locking pin injection-molded plastic complete part

24 2 glue in rudder horn injection-molded plastic complete part

25 2 linkage connector metal complete part Ø 6mm

26 2 washer metal M2

27 2 nut metal M2

28 2 hexagon-socket worm screw

for connecting the linkage metal M3

29 1 Allan key metal size 1.5

Wire kit

30 2 steel wire for elevator and

rudder with Z-bend metal Ø 0.8 x 613 mm

31 2 external Bowden pull wire

sleeve for elevator and rudder plastic Ø 3/2 x 515 mm

32 1 external Bowden for the antenna plastic Ø 3/2 x 640 mm

33 2 internal Bowden pull wire sleeve plastic Ø 2/1 x 550 mm

for elevator and rudder

34 1 spar connector glass fibre reinforced tube Ø 8 x 1 x 495 mm

Driving set

40 1 propeller plastic 125 x 110 mm

41 1 drive motor Permax 400 6V complete part

Fuselage

Canopy

L.H. wing

panel

Rudder

Elevator

Fin

Tailplane

Motor pod

R.H. wing

panel

Longitudinal axis

vertical axis

lateral axis

Basic information relating to model aircraft

Any aircraft, whether full-size or model, can be controlled around the three primary axes: vertical (yaw), lateral (pitch) and

longitudinal (roll).

When you operate the elevator, the model’s attitude alters around the lateral axis. If you apply a rudder command, the model

swings around the vertical axis. If you move the aileron stick, the model rolls around its longitudinal axis. As our EasyStar has

considerable wing dihedral, ailerons are not required for roll control. In this case the rudder is used both to turn the model

around the vertical axis, and also to roll it (longitudinal axis). External influences such as air turbulence may cause the model

to deviate from its intended flight path, and when this happens the pilot must control the model in such a way that it returns to

the required direction. The basic method of controlling the model’s height (altitude) is to vary motor speed (motor and propeller).

The rotational speed of the motor is usually altered by means of a speed controller. Applying up-elevator also causes the model

to gain height, but at the same time it loses speed, and this can only be continued until the model reaches its minimum

airspeed and stalls. The maximum climb angle varies according to the power available from the motor.

Wing section

The wing features a cambered airfoil section over which the

air flows when the model is flying. In a given period of time

the air flowing over the top surface of the wing has to cover a

greater distance than the air flowing under it. This causes a

reduction in pressure on the top surface, which in turn creates

a lifting force which keeps the aircraft in the air. Fig. A

Centre of Gravity (CG)

To achieve stable flying characteristics your model aircraft must

balance at a particular point, just like any other aircraft. It is

absolutely essential to check and set the correct CG position

before flying the model for the first time.

The CG position is stated as a distance which is measured

aft from the wing root leading edge, i.e. close to the fuselage.

Support the model at this point on two fingertips (or - better -

use the MPX CG gauge, # 69 3054); the model should now

hang level. Fig. B

If the model does not balance level, the installed components

(e.g. flight battery) can be re-positioned inside the fuselage. If

this is still not sufficient, attach the appropriate quantity of

trim ballast (lead or plasticene) to the fuselage nose or tail

and secure it carefully. If the model is tail-heavy, fix the ballast

at the fuselage nose; if the model is tail-heavy, attach the

ballast at the tail end of the fuselage.

The longitudinal dihedral is the difference in degrees between

the angle of incidence of the wing and of the tail. Provided

that you work carefully and attach the wing and tailplane to

the fuselage without gaps, the longitudinal dihedral will be

correct automatically.

If you are sure that both these settings (CG and longitudinal

dihedral) are correct, you can be confident that there will be

no major problems when you test-fly the model. Fig. C

Control surfaces, control surface travels

The model will only fly safely, reliably and accurately if the

control surfaces move freely and smoothly, follow the stick

movements in the correct “sense”, and move to the stated

maximum travels. The travels stated in these instructions have

been established during the test-flying programme, and we

strongly recommend that you keep to them initially. You can

always adjust them to meet your personal preferences later

on.

Transmitter controls

The transmitter features two main sticks which the pilot moves

to control the servos in the model, which in turn operate the

control surfaces.

The functions are assigned according to Mode A, although

other stick modes are possible.

The transmitter controls the control surfaces as follows:

Rudder (left / right) Fig. D

Elevator (up / down) Fig. E

Throttle (motor off / on) Fig. F

Unlike the other controls, the throttle stick must not return to

the neutral position automatically. Instead it features a ratchet

so that it stays wherever you put it. Please read the instructions

supplied with your radio control system for the method of

setting up and adjusting the transmitter and receiving system.

MULTIPLEX Modellsport GmbH & Co.KG • Neuer Weg 2 • D-75223 Niefern-Öschelbronn • www.multiplex-rc.de

"Bilderbuch "

"Illustrations"

"Ilustr azioni"

"Ilustr aciónes"

A B

Auftriebskraf t

BK + Permax 400/6V # 21 4192

RTF-Modell # 1 3200

Abb. 1

Abb. 2

Abb. 4

Abb. 3

Abb. 5

RTF*

3/4

3mm

Abb. 6

Abb. 8

Abb. 10

Abb. 12

Abb. 7

Abb. 9

Abb. 11

Abb. 13

max.

2,5 mm

Abb. 14

Abb. 16

Abb. 18

Abb. 20

Abb. 15

Abb. 17

Abb. 19

Abb. 21

23 (2x)

MULTIPLEX EasyStar Building Instructions

Marca: MULTIPLEX

Modello: EasyStar

Categoria: Giocattoli telecomandati

Tipo: Building Instructions

Scarica il pdf

rapporto

in altre lingue

English: MULTIPLEX EasyStar

MULTIPLEX EasyStar Building Instructions

MULTIPLEX EasyStar Building Instructions

in altre lingue

Documenti correlati

Altri documenti