Viper AS710R Manuale utente

Ride-on Scrubbers

USER MANUAL

READ USER MANUAL CAREFULLY BEFORE USE

Model #

Serial No.#

VR10029EU REV.01

2015-2-26

2

TABLE OF CONTENTS

ENGLISH

USER MANUAL………………………………………..………

1-16

DEUTSCH BETRIEBSANLEITUNG………………………………………..

17-29

FRANÇAİS MANUEL UTILISATEUR………………………………………..

30-42

NEDERLANDS GEBRUIKERS HANDLEIDING……………………………..…

43-55

ITALIANO MANUALE D’USO……………………………………………....

56-68

ESPAÑOL INSTRUCCIONES DE USO…………………………………

69-81

PORTUGUÊS MANUAL DO UTILIZADOR…………………………………....

82-94

ΕΛΛΗΝΙΚΆ ΕΓΧΕΙΡΙ∆ΙΟ ΧΡΗΣΤΗ…………………………………….….…

95-108

ČESKÝ UŽIVATELSKÝ MANUÁL……………………………………....

109-121

POLSKI INSTRUKCJA OBSŁUGI……………………………………….

122-134

MAGYAR FELHASZNÁLÓI KÉZIKÖNYV………………………………..

135-146

ROMÂNĂ MANUALUL UTILIZATORULUI…………………………….....

147-159

РУССКИЙ НСТРУКЦИЯ ПО ПРИМЕНЕНИЮ……………………..……

160-172

БЪЛГАРСКИ РЪКОВОДСТВО НА ПОТРЕБИТЕЛЯ……………………....

173-185

SLOVENŠČINA NAVODILA ZA UPORABO…………………………………..…

186-197

SLOVAK

POUŽÍVATEĽSKÁ PRÍRUČKAUSER MANUAL

………………..

198-209

WIRING DIAGRAM

210

3

4

5

ENGLISH USER MANUAL

6

SAFETY PRECAUTIONS

This machine is intended for commercial use. It is constructed for use in an indoor environment

and is not intended for any other use. Use only with recommended accessories.

All operators shall read, understand and exercise the following safety precautions:

1) DO NOT OPERATE MACHINE:

• Unless trained and authorized.

• Unless you have read and understand the user manual.

• In flammable or explosive areas.

• If not in proper operating condition.

• In outdoor areas.

2) BEFORE OPERATING MACHINE:

• Make sure all safety devices are in place and operate properly.

3) WHEN USING MACHINE:

• Go slow on inclines and slippery surfaces.

• Follow all safety guidelines.

• Be very careful when using the machine in reverse.

• Report and repair any damage to machine prior to operating it.

4) BEFORE LEAVING OR SERVICING MACHINE:

• Never park the machine on a slope.

• Turn machine off.

5) WHEN SERVICING MACHINE:

• Read user manual thoroughly prior to operating or servicing this machine.

• Use manufacturer supplied or approved replacement parts.

• Use approved jack or hoist to safely elevate the machine.

• Disconnect batteries prior to working on machine.

• Wear gloves when handling batteries or battery cables.

• Avoid moving parts. Do not wear loose fitting clothing while servicing machine.

6 SAFETY DEVICES

• Emergency-stop button(A15)

The machine comes to a sudden halt including all functions and no display can be

seen on the control panel A13 when you press the emergency-stop button.

• Safety button (A1).

Switch off the drive motor after a 0.5 second delay, if the operator leaves the operator

seat during operation or while moving. The LED screen displays STOP.

USER MANUAL ENGLISH

7

Batteries emit hydrogen. Explosion or fire can result from hydrogen. Keep sparks and

open flames away! It is recommended to push the button (C2) to turn recovery tank open

before charging.

Flammable materials can cause an explosion or fire. Do not use flammable materials in

tanks.

Flammable materials or reactive metals can cause an explosion or fire. Do not pick up by

hand.

WARNING It indicates a potential risk of injury or dangerous situation with risk

of death for the operator.

NOTED It indicates a remark related to important reminding or useful

functions.

MACHINE SET UP & INSTALLATION

UNPACKING MACHINE

Be sure and check packing carton for any damage. Report immediately any damage to carrier.

Check contents of package to ensure that the following items are included:

1. Machine

2. Squeegee assembly

3. Brush assembly (x2)

4. User manual

5. Battery charger (If equipped)

6. Batteries (x4) (If equipped)

7. Connecting wire for battery and charger (If equipped)

8. Warning lamp (If equipped)

9. Bumper bracket (If equipped)

BATTERY CONNECTIONS

1. Turn off the key switch (E5).

2. Turn the seat (A1) open, push board (C2) and turn recovery tank (A3) open. If machine does

not include batteries. Fit batteries suitable to your requirements.

After selecting batteries, please choose WET or GEL mode with toggle switch on the back

of PCB, as shown in the figure below.

ENGLISH USER MANUAL

8

3. Carefully place the four batteries into the compartment as shown in figure below. Place the

battery brace at the front of the four batteries.

4. Connect battery cables to posts in numbered order as shown in the figure below.

5. Apply a coat or protective spray on the cable connections to prevent battery corrosion.

6. Cover recovery tank and seat.

Make sure the recovery tank is empty when turn it.

Do not drop batteries into compartment. Do not put metal on the batteries.

Never connect + to +, or - to - , never connect + to – with single battery, when

disassembling or installing the batteries.

MACHINE SET UP

PRE-OPERATION CHECKS

1. Sweep or dust mop the surface to be cleaned.

2. Check battery meter to make sure batteries are fully charged. (see BATTERY CHARGING)

3. Check that brush / pad is properly installed.

4. Check that squeegee is properly installed.

5. Check the speed driver (A9) is work normally.

6. Make sure the recovery tank is empty. If not, drain it.

7. Make sure solution tank water indicator (E10) is not on. If on, fill water in solution tank (A4).

USER MANUAL ENGLISH

9

8. Check that the water valve (D2) is not indicated “0”.

INSTALLING PAD DRIVER OR BRUSH

1. Ensure that the machine is turned off (E5).

2. Raise the brush head (A7) off the floor by trampling the front of foot pedal (A10) on the left

of machine.

3. Put brushes (A8) below both driver motor hub.

4. Lower the brush head (A7) assembly by trampling the rear of foot pedal (A10). And sitting on

the machine to start brush switch (E3). Lightly depress driver pedal (C6), then brushes

automatic installed. If installation cannot be performed successfully in one shot, turn off brush

switch (E3) and reset the suit position to install brushes.

5. Adjusting the nut (A6) to properly place for work.

Never work without the brusher/pad perfectly installed.

When cleaning or replacing the brushes, you should raise the brush head and rotate the

reverse direction to “working” direction quickly. The two brushes are reverse in

direction.

INSTALLING AND ADJUSTING THE SQUEEGEE

1. Ensure that the machine is turned off (E5).

2. Turn the squeegee lift lever (C5) to put down the squeegee bracket (A5) on floor.

3. Loosen the two knobs (B2) on the squeegee and slide the squeegee into the slots in the back of

the squeegee bracket.

4. Tighten the knobs(B2) securely.

5. Secure the vacuum hose (B3) on the pick-up tube of the squeegee.

6. Adjusting the nut (B1) to properly place for suction.

FILLING THE SOLUTION TANK

1. It can be filled in water use a hose under the seat (C4).

2. Do not overfill the solution tank. Leave at least two inch from the opening of tank.

3. Water temperature should not exceed 40°C.

Depress the front,

Brushes up

Depress the rear,

Brushes down

ENGLISH USER MANUAL

10

Use only low-foam and non-flammable detergents suitable for ride-on scrubber

applications.

Each time when you need to fill the solution tank, always empty and clean the

recovery tank by removing the drain hose plug(C1). After each use, unscrew the drain

cap (D1) to drain solution tank.

CHECKING THE SPEED DRIVER

1. Sit on seat (A1) of the machine.

2. Turn on the key switch (E5).

3. Lightly depress the driver pedal (C6) to move and release it checking the machine forward or

stop.

4. For more security, you need to press the Emergency-stop button (A15) to make machine

sudden halt to check the button is work, when you use the machine for the first time. Release

it by turning.

5. If the drive motor error indicator (E4) is on, you must pay more attention. see ERROR

INFORMATION

The gradient in the direction of travel should not exceed (10) %.

The brake of drive motor is active when the machine is running normally, that is the

brake bracket is close to motor main body. When machine is on package \un-package

or machine error and some special situations, brake bracket will pull out, and use

washer to choke so the machine can move by hand pushing.

MACHINE OPERATION

Do not operate machine unless you have professional training. You have read and

understand this manual before operate machine.

1. You should sit on the seat of the machine when you operate it.

2. Lower squeegee assembly to the floor.

Make sure to raise the squeegee before the machine is moving backward, or machine

stops and LED screen displays ERR-01.

3. Lower the brush head to the floor.

You’d better to turn off the brush motor button before raising the brush to prevent

water throw out. You’d better to raise the brush head before the machine is reverse.

Don’t make brushes work in a same place for a long time to damage the floor.

USER MANUAL ENGLISH

11

4. Turn on the key switch.(E5)

5. Turn on the brush motor switch.(E3)

6. Depress the driver pedal slowly (C6) and turn steering wheel (A14) to forward. The speed can

be controlled by a dial (E6), turning left decreases speed, and turning right increases speed.

And to reverse, you can press the switch (E7).

7. Adjust amount of solution flow by pressing the solution/water adjustment button. (D5)

8. As long as you turn on the key switch (E5), you can charge the cell-phone through the USB

charging interface (A11).

9. You may press the horn (E9) for alert in case of encountering unexpected crowds or heavy

crowds.

When battery indicator is red and flashing, do not continue to operate the machine;

otherwise, this will cause harm to the batteries or machine. Recharge batteries.

Regularly view the clear tube (C7). If tank runs empty, turn off the brush switch,

solution switch and raise the brush head. Keep the squeegee down and continue to

vacuum until all dirty water is picked up.

Regularly view the filter (D3) and clean it by unscrewing the transparent cover.

If the squeegee assembly leaves streaks on the floor, raise the squeegee off the floor

and wipe the blades down with a damp cloth.

Do not use your fingers to wipe or remove debris from the blades, as injury may

occur.

The two brush motors \vacuum motor \drive motor\control circuit are equipped with

an overload protector (F3), which protects them from being overloaded. If overload

protector trips, it can’t be reset immediately. You must first determine what caused

the breaker to trip, and allow the motor to cool down before you can reset the breaker.

BATTERY CHARGING

Please use approved chargers to charge the batteries, while the machine is not equipped

with on-board battery charger.

For good machine performance, always keep batteries charged at all times. Do not let them

be in an over-discharged condition.

When charging the machine, make sure the transparent cover is open.

Charge the batteries when the red indicator (E11) on.

1. Charge the machine in a well-ventilated area.

ENGLISH USER MANUAL

12

2. Turn machine off (E5).

3. Plug approved charger into grounded wall outlet. Open transparent cover (A9), and then

connect the charging cable to the machine socket (F1).

4. The charger will automatically begin to charge the batteries.

5. Check that the battery charging is complete. Charging indicator (F2) is green.

6. Upon completion of charging, first unplug the charger from the wall outlet, and then

disconnect the charger from the machine.

7. Storage the charging cable in the below chair (C3).

Check battery connections for wear and loose terminals. Replace if necessary.

When charging the machine, please do not use machine.

Battery mode setting up method of the charger.

Do not to set charger unless you have professional training.

DIPSWITCH: SW1 (ONLY FOR)

MACHINE STORAGE

If the machine is not going to be used for more than 30 days, please proceed with the following

actions:

1. Perform the “After each use” maintenance procedures. (See Maintenance section).

2. Raise brush and squeegee.

3. Store machine in a clean, dry and no slope place. If storage in an area that may reach freezing

temperatures, be sure to drain all fluids from the machine prior to storage. Any damage caused

by freezing will void the warranty.

MAINTENANCE

Maintenance procedures must be performed with the machine turned off and battery

charger cable disconnected.

DP1 DP2 CHARGING CURVE

ON OFF IUIa-ACD for Lead-acid (Wet) batteries

OFF OFF IUIa-GEL for Gel batteries of Exide-Sonnenschein

OFF ON IUU0-GEL for HAZE Gel and AGM batteries of other manufacturers

ON ON IUIUa-AGM for Discover AGM batteries

USER MANUAL ENGLISH

13

All maintenance procedures must be performed by qualified personnel, or by authorized

Service Center. This Manual describes only the most common maintenance. For

additional maintenance procedures, contact your local Service Center.

SCHEDULED MAINTENANCE TABLE

Procedure After each use Weekly Every six mouths Annually

Battery charging

Clean Squeegee

Clean Brush/Pad

Clean Tank and vacuum grid

with float, cover gasket

check

Squeegee blade check and

replacement

Recovery filter cleaning

Clean solution pipe filter

Screw and nut tightening

check

1

lubricate rotary parts 1

Brush/Pad-holder motor

carbon brush check or

replacement

2

Vacuum system motor

carbon brush check or

replacement

2

Drive motor check or

replacement

2

1 And after the first 8 working hours.

2 This maintenance procedure must be performed by an authorized Service Center.

SQUEEGEE CLEAN AND BLADE REPLACEMENT

For optimal performance, the squeegee blades must be clean, dry and undamaged. If

damaged, replace it.

1. Unscrew the knob (B2) to remove squeegee.

2. Unscrew the left and right knob to relax the front clamp, replace the front blade.

3. Disengage the retainers (B4) and remove the rear clamp, replace the rear blade.

4. Install the blades in the reverse order to removal.

5. Install the squeegee to screw the knob (B2).

ENGLISH USER MANUAL

14

LED SCREEN DISPLAY INFORMATIONS

STOP Machine doesn’t move and brush doesn’t work, vacuum motor can work

00012.3 Machine add up driver time is 12.3hours

L0-18 Batteries voltage is lower 18V

U-25.5 Batteries voltage is 25.5V

ERR-01 Squeegee pulls down before machine reverse

DRIVE MOTOR ERROR INDICATOR INFORMATION

LED FLASH CODES EXAMPLE, ¤¤ ¤¤¤¤ means LED flash 2 times, after several seconds LED

flash 4 times.

LED is always light in normal work.

LED FLASH CODES DESCRIPTION

1.1

¤ ¤ Overheating >92°,motor overload

1.2

¤ ¤¤ Accelerator malfunction

1.3

¤ ¤¤¤ Speed limiter potentiometer malfunction

1.4

¤ ¤¤¤¤ Under-voltage malfunction

1.5

¤ ¤¤¤¤¤ Overvoltage malfunction

2.1

¤¤ ¤ Principal contactor actuator opening failure

2.2

¤¤ ¤¤ Principal contactor bond

2.3

¤¤ ¤¤¤ Principal contactor malfunction, faulty electrical brake coil

2.4

¤¤ ¤¤¤¤ Principal contactor actuator closing failure

3.1

¤¤¤ ¤ Accelerator potentiometer malfunction

3.2

¤¤¤ ¤¤ Brake activation malfunction

3.4

¤¤¤ ¤¤¤¤ Brake deactivation malfunction

3.5

¤¤¤ ¤¤¤¤¤ HPD malfunction(incorrect regulation of accelerator potentiometer)

4.1

¤¤¤¤ ¤ Motor short circuit

4.2

¤¤¤¤ ¤¤ Incorrect motor voltage/short circuit in motor

4.3

¤¤¤¤ ¤¤¤ EEPROM malfunction

4.4

¤¤¤¤ ¤¤¤¤ Short circuit in motor/EEPROM error

USER MANUAL ENGLISH

15

Parameter

Model AS710R

Machine length/width/height

1580*760*1230

Solution tank capacity

120L

Recovery tank capacity

120L

Rear wheels diameter

300MM

Brush motor power

2x300W

Vacuum motor power

500W

Drive motor power

500W

Max. driver speed

6km/h

Sound level

69dB(A)

Batteries length/width/height(standard)

4x245AH(20hours)

Batteries spec

241*168*300

Working capacity, up to

1800mm H

2

O

Cleaning productivity

4413sq.m/h

Squeegee width

940MM

Brush diameter

2x355MM

Brush rpm

204rpm/min

Charger(standard)

24V 25A

Machine weight

225KG

Machine weight(gross)

400KG

Carton spec 1730*810*1410

USB charger spec 5V, 0.8A

Gradient 10%

ENGLISH USER MANUAL

16

TROUBLESHOOTING

Trouble Possible Cause Remedy

The machine does not work, LED

screen (E1 ) does not turns on

The battery connector is disconnected Connect.

The batteries are completely discharged Charge the batteries

The machine does not work,

indicator light ( E11) is red

The batteries are discharged Charge the batteries

The machine does not forward or

back

The PCB or key board is broken Change the PCB or key board

Emergency-stop button (A15) does not

release

Turn and release

Seat limit switch is not activated. Sit on the seat of machine

Squeegee has not lifted in reverse, LED

screen (E1) display ERR-01

Before reversing, lift the squeegee

Brush motor does not work,

indicator light does not turns on

The PCB or key board is broken Change the PCB or key board

The deck motor is overloaded

Use less aggressive brushes suitable

for the floor to be cleaned, reset the

breaker

There are foreign materials preventing

the brush from rotating

Clean the brush hub

Drive motor does not work

Error indicator (E4) is lit Refer to ERROR INFORMATION

Drive motor is overloaded

Check the drive motor, reset the

breaker

Vacuum system motor does not

work

The recovery tank is full, light (E2) is red

Empty the recovery tank

The vacuum motor is overloaded

Check the vacuum motor, reset the

breaker

The PCB or key board is broken Change the PCB or key board

The dirty water vacuuming is

insufficient

The recovery tank is full, light (E2) is red

Empty the recovery tank

The hose is disconnected from the

squeegee

Re-connect

Vacuum assembly is clogged Clean or check

The squeegee is dirty, or the squeegee

blades are worn or damaged

Clean and check the squeegee

The tank cover (A2) is not properly

closed, or the gasket is damaged

Close the cover properly or replace

the gasket

The solution flow is insufficient

The solution filter (D3) is dirty, Clean the filter

The solution is empty, light (E10) is red Full in water

Water switch (D2) indicate “0” Open the water switch

The solution is dirty Clean the solution

The squeegee leaves marks on the

floor

There is debris under the squeegee blades

Remove the debris

The squeegee blades are worn, chipped

or torn

Replace the blades

Machine cannot brake Do not start the drive motor brake Brake bracket

is choked

BEDIENUNGSANLEITUNG DEUTSCH

17

SICHERHEITSHINWEISE

Diese Maschine ist für den kommerziellen Einsatz vorgesehen. Sie wurde für den Einsatz in

Innenräumen konstruiert und ist nicht für andere Zwecke vorgesehen. Verwenden Sie nur das

empfohlene Zubehör.

Alle Bediener müssen die folgenden Sicherheitshinweise lesen, verstehen und anwenden:

1) BEDIENEN SIE DIE MASCHINE NICHT:



Es sei denn, Sie sind darin geschult und dazu autorisiert.



Es sei denn, Sie haben das Benutzerhandbuch gelesen und verstanden.



In brennbaren oder explosiven Bereichen.



Wenn sie sich nicht im korrekten Betriebszustand befindet.



Im Außenbereich.

2) VOR DEM BETRIEB DER MASCHINE:



Stellen Sie sicher, dass alle Sicherheitseinrichtungen vorhanden sind und

ordnungsgemäß funktionieren.

3) BEIM BETRIEB DER MASCHINE:



Fahren Sie auf geneigten und glatten Flächen langsam.



Befolgen Sie alle Sicherheitsrichtlinien.



Seien Sie besonders vorsichtig, wenn Sie mit der Maschine rückwärts fahren.



Melden und reparieren Sie vor dem Betrieb alle Schäden an der Maschine.

4) VOR DEM ABSTELLEN ODER DEM WARTEN DER MASCHINE:



Stellen Sie sie nie an einem Hang ab.



Schalten Sie die Maschine aus.

5) BEI DER WARTUNG DER MASCHINE:



Lesen Sie das Benutzerhandbuch vor dem Betrieb oder der Wartung dieser Maschine

sorgfältig durch.



Verwenden Sie nur vom Hersteller gelieferte oder zugelassene Ersatzteile.



Verwenden Sie nur zugelassene Fahrzeugheber oder zugelassenes Hebezeug, um die

Maschine sicher anzuheben.



Trennen Sie die Batterien vor Arbeiten an der Maschine.



Tragen Sie Handschuhe beim Umgang mit Batterien oder dem Batteriekabel.



Halten Sie sich von sich bewegenden Teilen fern. Tragen Sie während der Wartung der

Maschine keine lose anliegende Kleidung.

6) SICHERHEITSVORRICHTUNGEN



Not-Aus-Taster (A15)

Alle Funktionen der Maschine werden sofort beendet und auch das Bedienfeld zeigt

nichts mehr an (A13), wenn Sie den Not-Aus-Taster drücken.

DEUTSCH BEDIENUNGSANLEITUNG

18



Sicherheitstaste (A1).

Schaltet den Antriebsmotor nach einer Wartezeit von 0,5 Sekunden aus, wenn der

Bediener den Fahrersitz im Betrieb oder während der Fahrt verlässt. Der

LED-Bildschirm zeigt STOP an.

Die Batterien geben Wasserstoff ab. Wasserstoff kann zu Explosion oder Feuer führen.

Halten Sie Funken und offene Flammen fern! Es wird empfohlen, die Taste (C2) zu

drücken, um den Schmutzwasserbehälter vor dem Laden zu öffnen.

Brennbare Materialien können eine Explosion oder einen Brand verursachen.

Verwenden Sie keine brennbaren Materialien in den Tanks.

Brennbare Materialien oder reaktive Metalle können eine Explosion oder einen Brand

verursachen. Nicht von Hand hochheben.

WARNUNG: Weist auf ein potenzielles Risiko für Verletzungen oder gefährliche

Situationen mit Todesgefahr für den Bediener hin.

ACHTUNG: Ist ein Hinweis auf wichtige Anmerkungen oder nützliche

Funktionen.

MASCHINENEINRICHTUNG UND INSTALLATION

ENTPACKEN DER MASCHINE

Überprüfen Sie den Verpackungskarton auf Beschädigungen. Melden Sie irgendwelche Schäden

sofort an den Spediteur. Überprüfen Sie den Inhalt des Pakets, um zu gewährleisten, dass die

folgenden Teile enthalten sind:

1. Maschine

2. Rakelgruppe

3. Bürstengruppe (x2)

4. Benutzerhandbuch

5. Batterieladegerät (falls vorhanden)

6. Batterien (X 4) (falls vorhanden)

7. Verbindungskabel für Batterie und Ladegerät (falls vorhanden)

8. Kontrollleuchte (falls vorhanden)

9. Stoßfängerhalterung (falls vorhanden)

BATTERIEANSCHLÜSSE

1. Schalten Sie den Schlüsselschalter (E5) aus.

BEDIENUNGSANLEITUNG DEUTSCH

19

2. Drehen Sie den Sitz (A1) in die Position „Geöffnet“, drücken Sie die Platte (C2) und öffnen

Sie den Auffangtank (A3). Wenn die Maschine keine Batterien enthält, setzen Sie Batterien

entsprechend Ihren Anforderungen ein.

Stellen Sie nach der Auswahl der Batterien den Modus WET (Nass) oder GEL mit dem

Kippschalter auf der Rückseite der Platine ein, wie in der Abbildung unten gezeigt.

WET WET (NASS)

ON EIN

GEL GEL

3. Setzen Sie die vier Batterien vorsichtig in das Batteriefach ein, wie in der Abbildung unten

gezeigt. Setzen Sie die Batterieklammer an der Vorderseite der vier Batterien ein.

4. Schließen Sie die Batteriekabel an die Anschlüsse in der nummerierten Reihenfolge an, wie

in der Abbildung unten gezeigt.

5. Tragen Sie einen Film oder ein Schutzspray auf die Kabelanschlüsse auf, um Korrosion an

der Batterie zu verhindern.

6. Schließen Sie den Schmutzwassertank und den Sitz.

Vergewissern Sie sich, dass der Schmutzwassertank leer ist, wenn Sie ihn drehen.

Lassen Sie keine Batterien in das Fach fallen. Legen Sie kein Metall auf die Batterien.

Verbinden Sie niemals + mit + oder - mit -. Schließen Sie auch niemals die Plus- und

Minus-Pole einer einzelnen Batterie beim Demontieren oder Montieren kurz.

SCHWARZ

BATTERIEKLAM

ROT

DEUTSCH BEDIENUNGSANLEITUNG

20

MASCHINENEINRICHTUNG

KONTROLLEN VOR DER INBETRIEBNAHME

1. Fegen oder saugen Sie die zu reinigende Oberfläche vorher.

2. Überprüfen Sie die Batteriestandanzeige, um sicherzustellen, dass die Batterien voll

aufgeladen sind (siehe BATTERIE LADEN).

3. Überprüfen Sie, ob die Bürste bzw. der Pad ordnungsgemäß installiert ist.

4. Überprüfen Sie, ob die Rakel ordnungsgemäß installiert ist.

5. Überprüfen Sie, ob der Geschwindigkeitsregler (A9) ordnungsgemäß funktioniert.

6. Vergewissern Sie sich, dass der Schmutzwassertank leer ist. Entleeren Sie ihn, falls nicht.

7. Stellen Sie sicher, dass die Lösungstank-Wasseranzeige (E10) nicht leuchtet. Füllen Sie

Wasser im Lösungstank (A4) nach, falls sie leuchtet.

8. Überprüfen Sie, ob das Wasserventil (D2) nicht "0" anzeigt.

INSTALLATION VON PAD-ANTRIEB ODER BÜRSTE

1. Vergewissern Sie sich, dass die Maschine (E5) ausgeschaltet ist.

2. Heben Sie den Bürstenkopf (A10) vom Boden an, indem Sie links an der Maschine auf die

Vorderseite des Fußpedals (A7) treten.

3. Befestigen Sie die Bürsten (A8) unten an der Antriebsmotornabe.

4. Senken Sie die Bürstenkopfgruppe (A7) ab, indem Sie auf die Hinterseite des Fußpedals (A10)

treten, und starten Sie den Bürstenschalter (E3), während Sie auf der Maschine sitzen.

Drücken Sie das Fahrpedal (C6) leicht, dann werden die Bürsten automatisch installiert. Wenn

die Installation nicht auf einen Schlag erfolgreich ausgeführt wird, schalten Sie den

Bürstenschalter (E3) aus und überprüfen Sie die Einbauposition der Bürsten.

5. Ziehen Sie die Mutter (A6) für den Betrieb korrekt fest.

Betreiben Sie die Maschine nur, wenn die Bürste bzw. der Pad korrekt installiert ist.

Bei der Reinigung oder dem Austausch der Bürsten heben Sie den Bürstenkopf an und

drehen ihn schnell in die umgekehrte Richtung zur "Betriebs"-Richtung. Die beiden

Bürsten besitzen zueinander umgekehrte Drehrichtungen.

INSTALLATION UND ANPASSUNG DER RAKEL

1. Vergewissern Sie sich, dass die Maschine (E5) ausgeschaltet ist.

Drücken Sie auf die Vorderseite,

Bürsten heben sich

Drücken Sie auf die Rückseite,

Bürsten senken sich

La pagina sta caricando ...

Viper AS710R Manuale utente

Viper AS710R Manuale utente

in altre lingue

Documenti correlati

Altri documenti