Marantz SR7200 Manuale utente

Marca: Marantz

Modello: SR7200

Categoria: Ricevitori AV

Tipo: Manuale utente

Model SR7200 User Guide

AV Surround Receiver

ENGLISH

WARRANTY

For warranty information, contact your local Marantz distributor.

RETAIN YOUR PURCHASE RECEIPT

Your purchase receipt is your permanent record of a valuable purchase.

It should be kept in a safe place to be referred to as necessary for

insurance purposes or when corresponding with Marantz.

IMPORTANT

When seeking warranty service, it is the responsibility of the consumer

to establish proof and date of purchase. Your purchase receipt or in-

voice is adequate for such proof.

FOR U.K. ONLY

This undertaking is in addition to a consumer's statutory rights and does

not affect those rights in any way.

FRANÇAIS

GARANTIE

Pour des informations sur la garantie, contacter le distributeur local

Marantz.

CONSERVER L'ATTESTATION D'ACHAT

L'attestation d'achat est la preuve permanente d'un achat de valeur. La

conserver en lieu sur pour s'y reporter aux fins d'obtention d'une

couverture d'assurance ou dans le cadre de correspondances avec

Marantz.

IMPORTANT

Pour l'obtention d'un service couvert par la garantie, il incombe au cli-

ent d'établir la preuve de l'achat et d'en corroborer la date. Le reçu ou la

facture constituent des preuves suffisantes.

DEUTSCH

GARANTIE

Bei Garantiefragen wenden Sie sich bitte an Ihren Marantz-Händler.

HEBEN SIE IHRE QUITTING GUT AUF

Die Quittung dient Ihnen als bleibende Unterlage für Ihren wertvollen

Einkauf Das Aufbewahren der Quittung ist wichtig, da die darin

enthaltenen Angaben für Versicherungswecke oder bei Korrespondenz

mit Marantz angeführt werden müssen.

WICHTIG!

Bei Garantiefragen muß der Kunde eine Kaufunterlage mit Kaufdatum

vorlegen. Ihren Quittung oder Rechnung ist als Unterlage ausreichend.

NEDERLANDS

GARANTIE

Voor inlichtingen omtrent garantie dient u zich tot uw plaatselijke Marantz.

UW KWITANTIE, KASSABON E.D. BEWAREN

Uw kwitantie, kassabon e.d. vormen uw bewijs van aankoop van een

waardevol artikel en dienen op een veilige plaats bewaard te worden

voor evt, verwijzing bijv, in verbend met verzekering of bij correspondentie

met Marantz.

BELANGRIJK

Bij een evt, beroep op de garantie is het de verantwoordelijkheid van de

consument een gedateerd bewijs van aankoop te tonen. Uw kassabon

of factuurzijn voldoende bewijs.

ESPAÑOL

GARANTIA

Para obtener información acerca de la garantia póngase en contacto

con su distribuidor Marantz.

GUARDE SU RECIBO DE COMPRA

Su recibo de compra es su prueba permanente de haber adquirido un

aparato de valor, Este recibo deberá guardarlo en un lugar seguro y

utilizarlo como referencia cuando tenga que hacer uso del seguro o se

ponga en contacto con Marantz.

IMPORTANTE

Cuando solicite el servicio otorgado por la garantia el usuario tiene la

responsabilidad de demonstrar cuá¥do efectuó la compra. En este caso,

su recibo de compra será la prueba apropiada.

ITALIANO

GARANZIA

L’apparecchio è coperto da una garanzia di buon funzionamento della

durata di un anno, o del periodo previsto dalla legge, a partire dalla data

di acquisto comprovata da un documento attestante il nominativo del

Rivenditore e la data di vendita. La garanzia sarà prestata con la

sostituzione o la riparazione gratuita delle parti difettose.

Non sono coperti da garanzia difetti derivanti da uso improprio, errata

installazione, manutenzione effettuata da personale non autorizzato o,

comunque, da circostanze che non possano riferirsi a difetti di

funzionamento dell’apparecchio. Sono inoltre esclusi dalla garanzia gli

interventi inerenti l’installazione e l’allacciamento agli impianti di

alimentazione.

Gli apparecchi verranno riparati presso i nostri Centri di Assistenza

Autorizzati. Le spese ed i rischi di trasporto sono a carico del cliente.

La casa costruttrice declina ogni responsabilità per danni diretti o indiretti

provocati dalla inosservanza delle prescrizioni di installazione, uso e

manutenzione dettagliate nel presente manuale o per guasti dovuti ad

uso continuato a fini professionali.

PORTUGUÊS

GARANTIA

Para informações sobre a garantia, contactar o distribuidor Marantz lo-

cal.

GUARDAR O RECIBO DE COMPRA

O recibo é o registo permanente da compra que fez. Deve ser guardado

num local seguro, para ser apresentado em questões relacionadas com

o seguro ou para quando tiver de contactar a Marantz.

IMPORTANTE

Quando procurar assisténcia técnica ao abrigo da garantia, é da

responsabilidade do consumidor estabelecer a prova e data de compra.

O recibe é prova adequada.

SVENSKA

GARANTI

För information om garantin, kontakta Marantz lokalagent.

SPAR KVITTOT

Kvittot är ett inköpsbevis på en värdefull vara. Det skall förvaras säkert

och hänvisas till vid försäkringsfall eller vidkorrespondens mod Marantz.

VIKTIGT

Fö att garantin skall gälla är det kundens sak att framställa bevis och

datum om köpet. Kvitto eller faktura är tillräokligt bevis fö detta.

DANSK

GARANTI

Henvend dem til Deres MARANTZ-forhandler angående inrformation om

garantien.

GEM DERES KVITTERING

Deres købskvittering er Deres varige bevis på et dyrt køb. Den bør

gemmes godt og anvendes som bevis, hvis De vil tegne en forsikring,

eller hvis De kommunikerer med Marantz.

VIGTIGT

Det påhviler forbrugeren at skaffe bevis for købet og købsdatoen, hvis

han eller hun ønsker garantiservice. Deres købskvittering eller faktura er

et fuldgyldigt bevis herpå.

English

To ventilate the unit, do not install the unit in a rack or bookshelf, and

note the followings.

- Do not touch the top of the enclosure during operation.

- Do not block the openings in the enclosure during operation.

- Do not insert objects beneath the unit.

- Do not block the ventilation slots at the top of the unit.

Do not place anything about 1 meter above the top panel.

- Make a space of about 0.2 meter around the unit.

Français

Pour que l'appareil puisse être correctement ventilé, ne pas l'installer

dans un meuble ou une bibliothèque et respecter ce qui suit.

- Ne pas toucher le dessus du coffret.

- Ne pas obstruer les ouïes de ventilation du coffret pendant le

fonctionnement.

- Ne placer aucun objet sous l'appareil.

- Ne pas obstruer les ouães de ventilation du panneau supérieur. Ne

placer aucun objet à moins d'un mètre environ du panneau supérieur.

- Veiller à ce qu'aucun objet ne soit à moins de 0,2 mètre des côtés de

l'appareil.

Deutsch

Um eine einwandfreie Belüftung des Geräts zu gewährleisten, darf das

Gerät nicht in einem Gestell oder Bücherregal aufgestellt werden; die

folgenden Punkte sind besonders zu beachten:

- Während des Betriebs das Oberteil des Gehäuses nicht berühren.

- Während des Betriebs die Öffnungen im Gehäuse nicht blockieren.

- Keine Gegenstände in das Gerät einführen.

- Die Belüftungsschlitze an der Oberseite des Geräts dürfen nicht

blockiert werden. Darauf achten, daß über dem Gerät ein Freiraum

von mindestens 1 meter vorhanden ist.

- Auf allen Geräteseiten muß ein Zwischenraum von ungefähr 0,2 meter

vorhanden sein.

Nederlands

Installeer het toestel niet in een rek of boekenkast waar de ventilatie

mogelijk wordt gehinderd. Let tevens op de volgende punten:

- Raak de bovenkant van het toestel niet aan als het in gebruik is.

- Blokkeer de openingen van het toestel niet als het in gebruik is.

- Plaats geen onderwerpen onder het toestel.

- Blokkeer de ventilatie-openingen aan de bovenkant van het toestel

niet. Zorg dat er tenminste 1 meter vrije ruimte boven het toestel is.

- Zorg dat er 0,2 meter vrije ruimte rond het toestel is.

Español

Para ventilar la unidad no la instale en una estantería ni estante para

libros, y tenga en cuenta lo siguiente:

- No toque la parte superior de la caja durante el funcionamiento.

- No tape las ranuras en la caja durante el funcionamiento

- No ponga objetos debajo de la unidad.

- No tape las ranuras de ventilación de la parte superior de la unidad.

No ponga nada a menos de 1 metro por encima del panel superior.

- Deje un espacio de unos 0,2 metro alrededor de la unidad.

Italiano

Perch é l'unità possa essere sempre ben ventilata, non installarla in

scaffali o librerie e tenere presente quanto segue.

- Non toccare la parte superiore del rivestimento durante il

funzionamento.

- Non bloccare le aperture sul rivestimento durante il funzionamento.

- Non inserire oggetti al di sotto dell'unità.

- Non bloccare le fessure di ventilazione sopra l'unità.

Non posare nulla per circa un metro sopra il pannello superiore.

- Lasciare 0,2 metro liberi tutto intorno l'unità.

Português

Para ventilar o aparelho, não instalá-lo dentro duma estante ou algo

similar, e observar as seguintes recomendações:

- Não tocar a parte superior do aparelho durante a operação.

- Não bloquear as aberturas do aparelho durante a operação.

- Não insertar objectos debaixo do aparelho.

- Não bloquear as aberturas de ventilação na parte de cima do

aparelho. Deixar um espaço completamente livre de cerca de 1 metro

acima do painel superior.

- Deixar um espaço de cerca de 0,2 metro ao redor do aparelho.

Svenska

För att ventilera enheten, ställ den inte i ett ställ eller bokhylla och tänk

på följande.

- Vidrör inte ytterhöljets ovansida under pågående drift.

- Blockera inte öppningarna i ytterhöljet under pågående drift.

- Stick inte in föremål under enheten.

- Blockera inte ventialtionshålen ovanpå enheten.

Placera inte någonting närmare än 1 meter ovanför apparaten eller

enheten.

- Se till att det finns omkring 0,2 meter fri plats runt omkring enheten.

Dansk

Anbring ikke apparatet i et rack eller en boghylde, da dette kan bloke

luftcirkulationen omkring apparatet. Iagttag ligeledes følgende:

- Berør ikke oversiden af kabinettet under anvendelsen.

- Bloker ikke åbningerne i kabinettet under anvendelsen.

- Stik ikke genstande ind under apparatet.

- Bloker ikke ventilationsåbningerne ovenpå apparatet.

Anbring ikke noget nærmere end 1 m over apparatets overside,

- Sørg for, at der er et frit område på omkring 0,2 m omkring apparatet.

CE MARKING

English

The SR7200 is in conformity with the EMC directive and low-voltage directive.

Français

Le SR7200 est conforme à la directive EMC et à la directive sur les basses tensions.

Deutsch

Das Modell SR7200 entspricht den EMC-Richtlinien und den Richtlinien für Niederspannungsgeräte.

Nederlands

De SR7200 voldoet aan de EMC eisen en de vereisten voor laag-voltage.

Español

El SR7200 está de acuerdo con las normas EMC y las relacionadas con baja tensión.

Italiano

Il SR7200 è conforme alle direttive CEE ed a quelle per i bassi voltaggi.

Português

O SR7200 conforma com as diretrizes EMC e de baixa voltagem.

Svenska

SR7200 är tillverkad i enlighet med EMC direktiven och direktiven för lågvoltsutrusning.

Dansk

Model SR7200 er i overensstemmelse med EMC-direktiveet og direktivet om lavspænding.

AV SURROUND RECEIVER SR7200

SURROUND

VOLUME

DOWN

DSS/VCR2 AUX

VCR1

DVD

TV CD

CDR/MD

TAPE

TUNER

MEMORY

TUNING/PRESET

MODE

F/P

CLEAR

NIGHT

ATT

DISPLAY OFF

SLEEP

S-DIRECT

DIMMER

MUTE

A/D7CH INPUT

POWER ON/OFF

PHONES

STANDBY

AUX INPUT

BSPEAKERSA

MULTI ROOM

S-VIDEO VIDEO L AUDIO R

SLEEP

MUTE

ANALOG

DIGITAL

MLP PCM

RF AUTO LOCK CIRCLE SURROUND EX MPEG DIRECT MEMORY PRESET SW LFE

SRSCSLRTTAPTYAUTOTUNEDDSP SOUNDVIRTUAL

1 2 3 4 5 6

DIGITALDTS

THX

RCLCTTPEONRDSSTEREOTAPE 2 MON

PRO LOGIC

VIDEO SET

DOLBY

(75

Ω

)

GND

AUDIO

FRONT

MONITOR

CENTER

REMOTE CONTROL

OUT

CENTER

SURR.

CENTER

SURR.

W MAX

SWITCHED

SPEAKER SYSTEMS

VIDEO

COMPONENT

SPEAKER SYSTEMS

AC OUTLET

(230V 50Hz)

CENTERSURR.CENTER

SURROUND

FRONT

DVD

DSS

VCR2

OUT

VCR1

OUT

VCR2

DSS

TOR

MONI

VIDEO

OUT

VCR2

DSS

OUT

VCR1

MONITOR

ROOM

MULTI

VCR2

DSS

DVD

VCR1

DVD

VCR2

DSS

OUT

DVD

VCR1

VCR2

DSS

OUT

TAPE

CDR

MULTI

REMOTE

VCR2

DSS

VCR1

OUT

CDR

ROOM

MULTI

OUT

DIGITAL

DIG.OUT OPT

DIG

1 IN

DIG

2 IN

DIG.OUT COAX

DIG

3 IN

DIG

4 IN

DIG

5 IN

FRONT

SURR.

CENTER

SURR.

FRONT

WOOFER

SUB

WOOFER

SUB

OUT

CTRL

OUT

CTRL

OUT

PRE

ANTENNA

SPEAKER IMPEDANCE

FRONT A

CENTER,

SURROUND,

SURR. BACK

: 6

16 OHMS

FRONT A

AND

: 12

16 OHMS

INPUT

7CH

MEMO

CLEAR

GUIDE

MUTE

ENT

VOL

DVD

CD-R/MD

DSS

VCR

AMP

TUNER

TAPE

AUX

AUTO

DTS

CS5.1

6.1

DSP

6-STEREO

2CH OSD SLEEP

OFF

ON / OFF

SOURCE

MACRO

MODE

LEARNING REMOTE

CONTROL RC 7200SR

POWER

NIGHT

ATT

DISPLAY OFF

MULTI ROOM

SLEEP

MUTE

ANALOG

DIGITAL

AUTO CIRCLE SURROUND DIRECT MEMORY PRESET SW LFE

SRSCSLRTPTYAUTOTUNEDDSP SOUNDVIRTUALDIGITALDTS

RCLRDSSTEREO

PRO LOGIC

DOLBY

!9 @0

⁄0

⁄1

⁄2

⁄3

⁄4

⁄7

⁄6

⁄5

ui o !0!1

!4 !8!7!6!5

Speaker system

Attenuate

Display off

Night mode

⁄8

a s d f g h j kl ¡0 ¡1 ¡2 ¡3

¡4 ¡5 ¡6 ¡7 ¡8

¡9 ™0 ™1 ™2 ™3 ™4 ™5

Preset channel

Surround modeMulti room mode

Input indicator Memory

Direct mode

Tuned

FM stereo

RDS mode

Mute

Sleep timer

Auto tuning mode

Encoded channel status

iii

ENGLISH

TABLE OF CONTENTS

FOREWORD .................................................................................................................................................................... 2

PRECAUTIONS ........................................................................................................................................................................................................ 2

INTRODUCTION.............................................................................................................................................................. 3

DESCRIPTION................................................................................................................................................................. 3

FEATURES ...................................................................................................................................................................... 3

FRONT PANEL FEATURES ............................................................................................................................................ 4

REAR PANEL CONNECTIONS....................................................................................................................................... 5

REMOTE CONTROL UNIT RC7200SR........................................................................................................................... 8

OPERATION OF REMOTE CONTROL UNIT ........................................................................................................................................................... 8

SET-UP ............................................................................................................................................................................ 9

ON SCREEN DISPLAY MENU SYSTEM ................................................................................................................................................................. 9

OSD MAIN MENU .................................................................................................................................................................................................. 10

SYSTEM SETUP .................................................................................................................................................................................................... 10

SPEAKERS SETUP ............................................................................................................................................................................................... 11

SURROUND MODE ............................................................................................................................................................................................... 12

CHANNEL LEVEL CONTROL ................................................................................................................................................................................ 12

MULTI ROOM SETUP ............................................................................................................................................................................................ 12

BASIC OPERATION ...................................................................................................................................................... 13

LISTENING TO THE TUNER .................................................................................................................................................................................. 13

RDS OPERATION .................................................................................................................................................................................................. 14

PLAYBACK OPERATION ....................................................................................................................................................................................... 15

OTHER FUNCTIONS..................................................................................................................................................... 15

SETTING THE SLEEP TIMER ............................................................................................................................................................................... 15

TV AUTO ON/OFF FUNCTION .............................................................................................................................................................................. 15

MULTI ROOM SELECTOR ..................................................................................................................................................................................... 16

ON SCREEN DISPLAY INFOMATION .......................................................................................................................... 16

REMOTE CONTROL UNIT RC7200SR......................................................................................................................... 18

MAIN FEATURES & FUNCTIONS.......................................................................................................................................................................... 18

NAMES OF PARTS & FUNCTIONS ....................................................................................................................................................................... 18

BASIC OPERATION ............................................................................................................................................................................................... 20

OTHER FUNCTIONS ............................................................................................................................................................................................. 26

BATTERY LIFE ....................................................................................................................................................................................................... 26

NUMBER OF LEARNABLE CODES ...................................................................................................................................................................... 26

JOG DIAL COMMAND FUNCTIONS LISTING ...................................................................................................................................................... 27

SURROUND MODES .................................................................................................................................................... 28

TROUBLE SHOOTING .................................................................................................................................................. 30

ENGLISH

FOREWORD

This section must be read before any connection is made to the mains

supply.

WARNINGS

Do not expose the equipment to rain or moisture.

Do not remove the cover from the equipment.

Do not push anything inside the equipment through the ventilation

holes.

Do not handle the mains lead with wet hands.

EQUIPMENT MAINS WORKING SETTING

Your Marantz product has been prepared to comply with the

household power and safety requirements that exist in your area.

SR7200 can be powered by 230 V AC only.

IMPORTANT: (FOR UK VERSION)

This apparatus is fitted with an approved moulded 13 Amp plug.

To change a fuse in this type of plug proceed as follows:

1. Remove fuse cover and fuse.

2. Fix new fuse which should be a BS1362 13A, A.S.T.A. or BSI

approved type.

3. Refit the fuse cover.

If the fitted plug is not suitable for your socket outlets, it should be cut

off and an appropriate plug fitted in its place.

If the mains plug contains a fuse, this should have a value of 13A. If a

plug without a fuse is used, the fuse at the distribution board should

not be greater than 5A.

Note:

The severed plug must be destroyed to avoid a possible shock

hazard should it be inserted into a 13A socket elsewhere.

HOW TO CONNECT A PLUG

The wires in the mains lead are coloured in accordance with the

following code:

BLUE—“NEUTRAL” (“N”)

BROWN—“LIVE” (“L”)

1. The BLUE wire must be connected to the terminal which is

marked with the letter “N” or coloured BLACK.

2. The BROWN wire must be connected to the terminal which is

marked with the letter “L” or coloured RED.

3. Do not connect either wires to the earth terminal in the plug which

is marked by the letter “E” or by the safety earth symbol or

coloured green or green-and-yellow.

Before replacing the plug cover, make certain that the cord grip is

clamped over the sheath of the lead — not simply over the two wires.

Recording and playback of any material may require consent. For

further information refer to the following:

— Copyright Act 1956

— Dramatic and Musical Performers Act 1958

— Performers Protection Acts 1963 and 1972

— any subsequent statutory enactments and orders

ABOUT THIS USER GUIDE

Refer to the figures on page iii of this user guide. The numbers on the

figures correspond to those in the text. All references to the

connections and controls that are printed in BOLD type are as they

appear on the unit.

PRECAUTIONS

The following precautions should be taken when operating the

equipment.

GENERAL PRECAUTIONS

When siting the equipment ensure that:

— the ventilation holes are not covered;

— air is allowed to circulate freely around the equipment

— it is on a vibration free-surface;

— it will not be exposed to interference from an external source;

— it will not be exposed to excessive heat, cold, moisture or dust;

— it will not be exposed to direct sunlight;

— it will not be exposed to electrostatic discharges

Never place heavy objects on the equipment.

If a foreign body or water does enter the equipment, contact your

nearest dealer or service centre.

Do not pull out the plug by pulling on the mains lead, hold the plug.

It is advisable when leaving the house, or during a thunderstorm, to

disconnect the equipment from the mains supply.

PRECAUTIONS IN CONNECTION

• Be sure to unplug the power cable from the AC outlet or turn off the

POWER switch before proceeding with any connection.

• Connect one cable at a time observing the “input” and “output”.

This will avoid any cross connection between channels and signal

inputs and outputs.

• Insert the plugs securely. Incomplete connection may result in

noise.

• Prior to connecting other audio and video equipment to the SR7200,

please read their owner’s manuals.

INSTALLATION

If this unit or another electronic device incorporating a microcomputer

is used at the same time with the tuner or television, picture

disturbance or noise may occur. In such a case, install the unit

according to the following guide points.

• Separate the unit as far as possible from the television.

• Place the antenna wire for the tuner or TV apart from the power

cable and audio and video connection cables of this unit.

• Since the phenomenon is likely to occur when using an indoor

antenna and/or 300-ohm feeder wire, we recommend using an

outdoor antenna and 75-ohm coaxial cable.

ENGLISH

INTRODUCTION

Thank you for purchasing the Marantz SR7200 DTS/Dolby Digital

Surround receiver.

This remarkable component has been engineered to provide you with

many years of home theater enjoyment.

Please take a few minutes to read this manual thoroughly before you

connect and operate the SR7200.

As there are a number of connection and configurations options, you

are encouraged to discuss your own particular home theater setup

with your Marantz A/V specialist dealer.

DESCRIPTION

DTS was introduced in 1994 to provide 5.1 channels of discrete digital

audio into home theater systems.

DTS brings you premium quality, discrete multi-channel digital sound

to both movies and music.

DTS is a multi-channel sound system designed to create full range

digital sound reproduction.

The no compromise DTS digital process sets the standard of quality

for cinema sound by delivering an exact copy of the studio master

recordings to neighborhood and home theaters.

Now, every moviegoer can hear the sound exactly as the moviemaker

intended.

DTS can be enjoyed in the home for either movies or music on DVD’s,

LD’s, and CD’s.

]

Dolby Digital lets you enjoy Digital TV, Digital Satellite as well as DVD, LD

software in digital surround, which is the next step above Dolby Pro Logic.

In Comparison with Dolby Pro Logic, Dolby Digital can provide

separate left surround and right surround channels, for more precise

localization of sound and a more convincing, realistic ambience.

And, with Dolby Digital all five main channels can be full ranged and a

subwoofer can be added to each channel, if desired.

By providing up to 5.1 channels of digital audio independently. Dolby

Digital lets you enjoy better sound quality and more powerful presence

than conventional Dolby Surround.

Pro Logic II, the next generation in Dolby Surround Pro Logic

technology, brings the excitement of surround sound to any existing

stereo mix, while making existing Dolby Surround mixes sound more

like discrete 5.1-channel surround sound. It works with CDs, VHS

tapes and TV shows, and MP3 files and radio broadcasts-converting

all of these source to surround sound, without the artifacts by other

matrix-decoding technologies.

Circle Surround is backward compatible, such that surround playback

is possible from any stereo or passive matrix-encoded material.

Five full-bandwidth, discrete channels of information can be extracted

from an enormous library of material not multi-channel encoded.

These sources include many of today’s DVDs and laser discs, as well

as most all video tape, VCD, Compact Disc, radio and television

broadcast material.

“Dolby”, “Pro Logic”, and the double-D symbol are trademarks of

Dolby Laboratories.

“DTS”, “ES” and “DTS Digital Surround” are trademarks of Digital

Theater Systems, Inc.

Circle Surround and the symbol are trademarks of SRS Labs, Inc.

Circle Surround technology is incorporated under license from SRS

Labs, Inc.

FEATURES

• Dolby Digital and DTS surround sound decoding, plus Dolby Pro

LogicII decoding, Circle Surround and a variety of additional

surround modes.

• 6.1 mode reproduces the original 6.1 channel soundfield by

extracting the surround back signal from surround left and surround

right channels.

• 192 kHz/ 24 bit decoding for highest possible fidelity and bandwidth,

and high-resolution playback of 192 kHz/ 24 bit PCM audio sources.

• 110 watts to each of the six main channels; the power amp section

features advanced, premium high-storage power supply capacitors,

and fully discrete output stages housed in cast aluminum heat sinks.

• 6.1 channel pre-amp outputs for connection to external components

such as a subwoofer and external power amplifiers.

• Seven-channel direct inputs accommodate future surround sound

formats or an external digital decoder.

• 5 Digital inputs, for connection to other sources, such as DVD, DSS,

CD, CD-R or MD.

• 2 Digital outputs for connection to CD-R or MD.

• High-quality AM (MW/LW) /FM tuner with 30 station presets.

• Source Direct switch bypasses, tone controls and bass management

for purest audio quality.

• S-video and composite video switching .

• On- Screen- Display with both Composite and “S” video.

• Front panel A/V inputs, with S-video .

• Easy to use, on-screen menu.

• Multi-room capability offers independent control of a second room

audio and video system.

• Supplied with RC7200SR Programmable Learning Remote Control.

• Radio Data System (RDS) provides information on FM broadcasts.

ENGLISH

FRONT PANEL FEATURES (SEE

PAGE iii.)

q POWER switch and STANDBY indicator

Press the button to turn the power ON, and press again to turn it OFF.

If the POWER switch is in the ON position, the power of this unit can

be turned ON/OFF by pressing the POWER button on the remote

control unit.

When this unit is in the standby mode with the POWER switch set to

the ON position, pressing one of the FUNCTION SELECTOR buttons

also allows to turn the power on.

The STANDBY indicator lights up when this unit is the standby mode

(power OFF) by the remote control unit.

w PHONES jack for stereo headphones

Conventional dynamic headphones can be plugged in here.

Notes:

When using headphones, turn off the speakers system A and B

with SPEAKERS buttons. The surround mode is switched auto-

matically to STEREO.

e SURROUND MODE Selector knob

When this knob is turned, the surround mode is switched in the

following sequence.

Note:

Not all modes will be present if an analog input is selected.

r VOLUME control knob

Adjusts the overall sound level. Turning the control clockwise

increases the sound level.

t FUNCTION SELECTOR buttons (AUDIO/

VIDEO)

These buttons are used to select the sources.

The video function selector, such as TV, DVD, VCR1, DSS/VCR2 and

AUX, selects video and audio simultaneously.

Audio function sources such as CD, TAPE, CD-R/MD and TUNER

may be selected in conjunction with a Video source.

This feature (Sound Injection) combines a sound from one source with

a picture from another.

Choose the video source first, and then choose a different audio

source to activate this function.

y 7CH INPUT button

Press this button to select the output of an external multi channel decoder.

u A/D (Analog/Digital) SELECTOR button

This is used to select between the analog and digital inputs.

Note:

This button is not used for an input source that is not connected to

a digital input.

i S. ( Source) DIRECT button

When this button is pressed, the tone control circuit is bypassed as

well as Bass Management.

Notes:

The surround mode is automatically switched to AUTO when the

source direct function is turned on.

Additionally, Speaker Configurations are fixed automatically as follow.

Front SPKR = Large

Center SPKR = Large

Surround SPKR = Large

Surround Center SPKR = Yes

Sub woofer = Yes

o SLEEP button

Set the sleep timer function with this button .

!0 DIMMER button

When this button is pressed once, the display is dimmed.

When this button is pressed twice, the display is turned off and

“DISPLAY OFF” indicator lights up.

Press this button again to turn the display ON again.

!1 MULTI (Multi Room) button

Press this button to switch the unit to multi room mode. “MULTI

ROOM” indicator lights up.

!2 MUTE button

Press this button to mute the output to the speakers. Press it again to

return to the previous volume level.

!3 CLEAR button

Press this button to cancel the station memory setting mode or preset

scan tuning.

!4 MEMORY button

Press this button to enter the tuner preset memory numbers and

station names.

!5 TUNING / PRESET UP and DOWN buttons

During reception of AM (MW/LW) or FM, you can scan the other

frequencies or select another preset station pressing these buttons.

!6 FREQUENCY / PRESET button

During reception of AM (MW/LW) or FM, you can change the function

of the UP/DOWN buttons for scanning frequencies or selecting preset

stations by pressing this button.

!7 FM MODE button

Press this button to select the auto stereo mode or mono mode when

the FM band is selected. The AUTO indicator lights in the auto stereo

mode.

!8 INFRARED SENSOR window

This window receives infrared signals from the remote control unit.

!9 SPEAKERS buttons

Press these buttons to select speakers systems A and/or B.

@0 AUX input jacks

These auxiliary video/audio input jacks accept the connection of a

camcorder, portable VCR, etc.

AUTO

DTS

DOLBY PL II

MOVIE

6CH STEREO MATRIXSTEREO

HALL

STADIUM

DOLBY

PRO LOGIC

DOLBY PL II

MUSIC

MOVIE

CS 5.1

6.1CH

SURROUND

VIRTUAL

ENGLISH

REAR PANEL CONNECTIONS

(SEE PAGE iii.)

All connections to the rear panel should be made with the entire

system powered off.

To avoid errors, it is advisable to connect one cable at a time between

the various components.

a FM antenna terminal (75 ohms)

Connect an external FM antenna with a coaxial cable, or a cable

network FM source.

AM antenna and ground terminals

Connect the supplied AM loop antenna. Use the terminals marked

“AM” and “GND”.

The supplied AM loop antenna will provide good AM reception in most

areas.

Position the loop antenna until you hear the best reception.

s PRE OUT jacks

Jacks for Front - L/R, Center,Surround and Surround center.

Use these jacks for connection to an external power amplifier.

d SUB WOOFER output jack

Connect to the input jack(s) of the power amplifier for subwoofer

channel or powered subwoofer.

f DC control output 1 & 2

Connect a device that needs to be triggered by DC under certain

conditions (screen, power strip, etc…) Use the system setup menu (3/

3) to determine the conditions by which these jacks will be active.

Note:

This output voltage is for (status) control only, It is not sufficient for

drive capability.

g MULTI OUT jacks (Audio)

Connect to the input jacks of the amplifier used to drive the speakers

in another room (Second zone).

h Analog audio outputs for audio source

equipment

TAPE and CD-R/MD

Connect each output to the audio inputs (REC in) of your recording

equipment.

j Analog audio inputs

CD, TAPE, and CD-R/MD

Connect the audio outputs of your source components to the input

jacks on the receiver.

k Video outputs

VCR1, and DSS/VCR2

Connect each output to the video input (REC in) of your video

recording equipment.

l MULTI OUT jack (Video)

Connect to the input jack of the TV monitor in another room (Second

zone).

¡0

TV MONI. (VIDEO/S-VIDEO) output jacks

Connect the TV MONI jack to your TV’s video input (VIDEO IN) jack.

You can connect your video equipment with S-VIDEO jacks if

possible, or the composite VIDEO jacks.

You must use the same type of connection from your video player into

the receiver, and out of the receiver into your TV.

Both must be composite video or both must be S-Video. You cannot

convert a signal from one type to the other.

When you connect to S-video connections, there will be no signal

output from the composite video jacks.

¡1 COMPONENT VIDEO outputs

Connect to these outputs to the component video inputs of a video

projector or monitor. When a source connected to one of the two

component video inputs is selected the signal will be sent to these

jacks.

¡2 SPEAKER SYSTEMS A terminals

FRONT Left & Right speakers output terminals

Connect to the front left & right speakers.

CENTER speaker output terminals

Connect to the center speaker.

SURROUND Left & Right speakers output terminals

Connect to the surround (rear) left & right speakers.

SURROUND Center speakers output terminals

Connect to the surround center speakers.

¡3 SPEAKER SYSTEMS B terminals

FRONT Left & Right speakers output terminals

Connect to the front left & right speakers.

Notes:

When you use the speaker systems A and B simultaneously, the

connected speakers which are impeadance 12 to 16 ohms must be

used.

¡4 7 CH INPUT jacks

Connect to the outputs of an external multichannel decoder.

¡5 DIGITAL outputs

Optical and Coaxial

Connect digital input of your digital recording equipment.

¡6 DIGITAL inputs

Dig.1,2 (Optical) and Dig. 3, 4, 5 (Coaxial)

Connect each input to the digital output of your source equipment.

Use the system setup menu to assign digital input to appropriate

source. (see page. 10)

Note :

The coaxial connections are not for AC-3 RF from the LD player, If

you want to decode this type of signal, an external demodulator

must be used.

¡7 REMOTE CONT. IN/OUT terminals

Connect to a Marantz component equipped with remote control (RC-

5) terminals.

¡8 MULTI ROOM REMOTE I/O terminals

IN : Connect to multi-room remote control device, available from

your Marantz dealer.

OUT : Connect to the Marantz component equipped with remote

control (RC-5) terminals in another room (Second zone).

¡9 Analog audio outputs for video source

equipment

VCR1, and DSS/VCR2

Connect each output to the audio inputs (REC in) of your video

recording equipment.

™0 Analog audio inputs for video source

equipment

TV, DVD, VCR1, and DSS/VCR2

Connect each input to the audio outputs of your video source

equipment.

ENGLISH

™1 Video inputs

Ex: TV, DVD, VCR1, and DSS/VCR2

Connect each input to the video outputs of your video source

equipment.

™2 S-video inputs

Ex: TV,DVD, VCR1,and DSS/VCR2

Connect each input to the S-video outputs of your video source

equipment.

™3 COMPONENT VIDEO inputs

Ex: DVD,and DSS/VCR2

Connect to the Y/Cr/Cb component video outputs of each your video

product to these jacks.

™4 AC OUTLET

Connect the power cables of components such as a DVD or CD player

to this outlet.

This provides power only when the SR7200 is turned on and is useful

for components which you use every time you play your system.

Caution:

In order to avoid potential turn-off thumps, anything plugged in

here should be powered up BEFORE the SR7200 is turned on.

™5 Power cable

Connect to AC power outlet.

SR7200 can be powered by 230V AC only.

ENGLISH

OUTPUT

INPUT

5-13VDC

INVERT

OUT

VIDEO/

EXT.CONT.IN

8 OHMS

REMOTE CONT.

SPEAKER SYSTEM

(75

Ω

)

GND

AUDIO

CENTER

REMOTE CONTROL

OUT

CENTER

SURR.

CENTER

SURR.

DVD

VCR1

VCR2

DSS

OUT

TAPE

CDR

MULTI

REMOTE

VCR2

DSS

VCR1

OUT

CDR

ROOM

MULTI

OUT

DIGITAL

DIG.OUT OPT

DIG

1 IN

DIG

2 IN

DIG.OUT COAX

DIG

3 IN

DIG

4 IN

DIG

5 IN

FRONT

SURR.

CENTER

SURR.

FRONT

WOOFER

SUB

WOOFER

SUB

OUT

CTRL

OUT

CTRL

OUT

PRE

INPUT

7CH

ANTENNA

SPEAKER IMPEDANCE

FRONT A

CENTER,

SURROUND,

SURR. BACK : 6

16 OHMS

FRONT A

AND

B : 12

16 OHMS

REMOTE CONTROL

OUT

REMOTE

MULTI

REMOTE

CONT.

OUT

REMOTE

CONT.

OUT

Other Marantz

Equipment (RC-5)

LINE IN

Powered subwoofer

Marantz MA6100

power amplifier

Subwoofer speaker

REMOTE CONTROL BUS CONNECTIONS

This unit is equipped with a remote control function.

By connecting this unit’s remote control jacks to a Marantz CD player

or tape deck equipped with remote control (RC-5) jacks, it allows

system remote control to operate.

Connect REMOTE CONTROL OUT jack of SR7200 to REMOTE

CONT. IN of other Marantz equipment, i.e. CD player or tape deck, by

using an RCA pin cable.

Note:

If a component equipped with remote control (RC-5) jacks has an

INT/EXT switch on the rear panel, set the switch to EXT when using

the system control function.

(Connection example)

SR7200 rear panel CD player rear panel Tape deck rear panel

Controlling the power ON/OFF of a power amplifier connected to

the SR7200 through Marantz remote control

1. Now the MA6100 can be turned ON / OFF in synchronism with the

power ON / OFF of the SR7200.

Notes:

n Be sure to connect the remote control bus before the procedure

above.

CONNECTION FOR A SUBWOOFER

Use this connection when using

a sub-woofer speaker.

You can also connect a powered

subwoofer.

ENGLISH

REMOTE CONTROL UNIT RC7200SR

This chapter describes the functions which need to control the

SR7200. See page 18 and following pages to refer other function of

the RC7200SR.

c POWER ON and OFF

These two buttons are use for turning on or off SR7200.

b LCD

Used to display information about currently selected modes and

functions.

n Jog Dial control

Rotate this dial to select commands displayed on the LCD for each

function. (see page 27)

Refer to follow.

Function

Jog Dial command

Note

AMP 1 A/D switches analog/digital input

2 ATT switches attenuator for analog input

3 NIGHT selects NIGHT mode for Dolby Digital

4 MR-ON turns multi-room mode on

5 MR-OF turns multi-room mode off

6 7-DIR activates 7-channel input

7 TRB+ increases treble

8 TRB- decreases treble

9 BAS+ increases bass

0 BAS- decreases bass

TUNER 1 FM FM band

2 AM AM/MW band

3 LW Long Wave band

4 T-MOD mono/stereo mode selector

5 SCAN programmed preset channel scan

6 STM selects station mode

7 F-DIR inputs a frequency directly

8 PTY selects PTY function

9 DISP selects display function

0 DWR selects DSR wave range

The marked “⊗” commands are not used for SR7200.

m ENT buttons

Press this button to enter the selected command by the Jog Dial.

, FUNCTION buttons

Press one of these buttons twice within 2 seconds to select the input

function of SR7200.

Press one of these buttons once to change the state of remote

commander.

. VOLUME up / down buttons

These buttons are used to raise and lower the SR7200’s volume level.

⁄0 CURSOR buttons

The cursor buttons can be used to navigate within on-screen menus of

SR7200.

⁄2 Channel up / down buttons

Used to controls the up/down function of tuner, or allows one to cycle

through the tuner presets.

⁄3 MUTE button

This button can be used to mute the sound temporarily.

⁄5 CLEAR button

This button is used to cancel certain memory or programming

operations.

⁄6 MEMO button

This button is used to enter the tuner preset memory numbers and

station names.

⁄7 TEN KEYPAD

They are useful for tuning a pre-set radio station and setting a station

name.

OPERATION OF REMOTE CONTROL UNIT

1. Remote control

The distance between the transmitter of the remote control unit and the

IR SENSOR of the SR7200 should be less than about 5 meters. If the

transmitter is pointed to a direction other than the IR SENSOR or if

there is an obstacle between them, remote control may not be possible.

Remote-controllable range

2. Loading batteries

The life of the batteries used with the remote control unit is about 4

months with normal use. Also be sure to replace batteries earlier when

you notice that they are getting weak.

(1) Remove the back cover.

(2) Insert the new batteries (AA type) with correct (+) and (–)

polarity.

(3) Close until it clicks.

Remote control unit (RC7200SR)

60°

SR7200

Approx. 5 m

⊗

ENGLISH

SET-UP

After all components are connected, initial setup must be performed.

ON SCREEN DISPLAY MENU SYSTEM

The SR7200 incorporates an on-screen menu system, which makes

various operations possible by using the cursor (<, >, ^, v) and OK

buttons on the remote controller.

The settings made with these buttons are also shown in the on-screen

display.

SURROUND MODE SYSTEM SETUP 1/3

SYSTEM SETUP 2/3

SPEAKER SETUP 1/3 SPKR SIZE

SPEAKER SETUP 2/3 SPKR DISTANCE

SPEAKER SETUP 3/3 SPKR LEVEL

CHANNEL LEVEL CONTROL

MULTI ROOM SETUP

OSD MAIN MENU

SYSTEM SETUP 3/3

ENGLISH

OSD MAIN MENU

1. Press the AMP button ,.

2. Press OK button ⁄0 to display the “MAIN MENU” of the on-screen

display menu.

Choose a desired item in the contents with ^ or v button, and

press the OK button to select.

Display will change to menu for each item.

SYSTEM SETUP

SYSTEM SETUP 1/3

7CH-INPUT : The 7 channel input of the SR7200 can be

selected to use a 7channel input. Select 7

channel use by < or > button.

TV AUTO : This product is equipped with a TV-auto ON/

OFF system, which automatically turns on or off

the power 1 second to 5 minutes after the TV

video input signal has been sent or has been

stopped.

Switch the TV AUTO ON/OFF function to enable

or disable with < or > button.

To use this function, connect the TV video input

to TV tuner’s video output.

NEXT SETUP/EXIT :If you desire to continue the next setup ,press

the OK button on NEXT-SETUP, if you desire to

exit from OSD menu system, press the OK

button on EXIT.

SYSTEM SETUP 2/3 (SELECTING THE DIGITAL INPUT)

Five digital inputs can be assigned for the desired source.

Use this menu to determine which source is connected to which input.

Example;

When the digital output of a DVD player is connected to Digital 4 (input

jack) of the SR7200;

1. Move the cursor on the line of the DVD with cursor buttons ^ or v.

2. Press the the cursor < or > button until “DIG4” is displayed.

3. Press the OK button to chose.

4. If you desire to continue the next setup, press the OK button on

NEXT-SETUP.

If you desire to exit from OSD menu system, press the OK button

on EXIT.

Notes:

The TUNER, VCR1, TAPE and AUX are assigned to the analog

input, and are prevented from selecting any digital input.

While the DTS-LD or DTS-CD is playing, this setup is not available,

this is to avoid noise being generated from the analog input. Stop

the LD or CD playback to setup.

The SR7200 does not switch from digital input to analog input or

vice versa automatically.

In the event that both digital and analog inputs are connected to

SR7200, if you desire to switch to an analog input temporarily, you

can switch by pressing the A/D button u.

SYSTEM SETUP 3/3 (DC CONTROL OUTPUT)

SR7200 has two DC control jacks, each one is selectable to link with

input functions for the main room or multi room.

You can select MAIN ROOM, MULTI ROOM or OFF for DC1 & DC2

independently by < or > button.

And then press OK button and move the cursor to select the linked

input function you desired by < or > button and press OK button to

chose.

Notes:

When the DC CONTROL OUTPUT is selected for the multi room,

the multi room must be turned on previously.

ENGLISH

SPEAKERS SETUP

The home theater system you already have installed should function

provided that there are left, center and right front speakers, left and

right rear/surround speakers and a subwoofer. For best results we

recommend that all front speakers be of the same type, with identical

or similar driver units. This will deliver smooth pans across the front

sound stage as the action moves from side to side.

Your center channel speaker is very important as over 80 % of the

dialog from a typical motion picture emanates from the center channel.

It should possess similar sonic characteristics to the main speakers.

Surround channel speakers need not be identical to the front channel

speakers, but they should be of high quality.

The surround center speaker is useful for playback of Dolby Digital

Surround EX or DTS-ES. One of the benefits of both Dolby Digital

(AC-3) and DTS is that surround channels are discrete full range,

while they were frequency limited in earlier “Pro Logic’ type systems.

Bass effects are an important part of home theater. For optimal

enjoyment a subwoofer should be used as it is optimized for low

frequency reproduction. If you have full range front speakers,

however, they may be used in place of a subwoofer with proper setting

of the switches in the menu system.

If possible, mount the surround speakers on the walls to the sides of

the viewing area, 2-3 feet above seated viewers, firing straight across

at each other.

SPKR SETUP 1/3 (SPKR SIZE)

SETUP: Select “LOCKED” with < or > button in order to lock the

contents of the SPKR SET UP MENU.

Then, when you want to change the contents of this setup,

select “UNLOCKED”.

SPKR SIZE

This menu enters the information about which type of speakers will be

used for each channel.

In turn, these settings will determine which speakers receive low

frequency information.

For the purpose of establishing proper bass reproduction, use the

LARGE settings if the speaker being used at any position is a

traditional full-range loudspeaker that is capable of reproducing sound

below 100 Hz and you are not using a subwoofer.

Use the SMALL setting for smaller, frequency-limited speakers that are not

able to reproduce sounds below 100Hz and you are using a subwoofer.

Low frequencies will be diverted from the speaker to the subwoofer.

Note that when “small” speakers are used it is advisable to install a

separate subwoofer, especially if you wish to appreciate the full

impact of a good home theater soundtrack.

If the Surround speakers or Center speaker will not be used, set

NONE for each speaker. The NONE setting will send the audio for the

channel to other speakers.

FRONT -L/R : Select the type of front speakers with < or > button.

CENTER : Select the type of center speaker with < or > button.

SURR-L/R : Select the type of surround speakers with < or > button.

SURR.CENTER : Select the surround center speaker YES or NO with

< or > button.

SUBWOOFER: Select the subwoofer speaker YES or NO with < or

> button.

Notes:

The SUBWOOFER cannot be set to NO when the front speakers

are set to SMALL.

This speaker size setup is not effective when the SOURCE-

DIRECT or 7CH. Input is selected.

SPKR SETUP 2/3 (SPKR DISTANCE)

Use this parameter to specify the distance of the speaker’s position

from the listener.

The delay time is automatically set according to these distances.

UNITS:You can select Meters or Feet.

If you select “ft”, the setting parameter will change in 1 foot

steps.

If you select “m”, it will change in 0.3 meter steps.

Select speaker with ^ or v button, and input each speaker’s

distance with < or > button.

When the input for each speaker’s distance has been finished,

move the cursor to ENTER and press the OK button.

Notes:

Placement beyond that distance is beyond the range of the

automatic time delay feature.

The delay feature does not function in the SOURCE-DIRECT ,7

CH-Input modes and decoding of 96 kHz sources.

SPKR SETUP 3/3 (SPKR LEVEL)

SPKR LEVEL

TEST MODE: Selects the mode for generating the test tone.

If you select AUTO, the test tone will be cycled through

in a circular pattern which is Left → Center → Right →

Surround Right → Surround Center → Surround Left →

Subwoofer → Left → ... 3 seconds for each channel.

If you select MANUAL, press the OK button to select the

test tone channels after the “TEST TONE ON”.

TEST TONE: Press the < or >button, ON is indicated and the test

tone starts from the front L-CH speaker.

Press the < or > button again on this item. OFF is

indicated and the output of the test tone will stop.

Channel: Adjust the level of test tone for each channel with the < or

> buttons of the RC7200SR. The current volume level is

shown at the center of the display.

Notes:

Test tone does not generate when the SOURCE DIRECT function

is turned on.

SUB WOOFER

LEFT

CENTER

RIGHT

SURROUND-L

SURROUND-R

SURROUND CENTER

ENGLISH

SURROUND MODE

SOURCE DIRECT : Switch the source direct ON or OFF with < or >

button. This bypasses the surround processing

and crossover for the main speakers (front left

and right will be full range and the subwoofer will

be ON)

Note: Surround mode cannot be changed in

Source Direct mode.

SURR-MODE : Select the surround mode with < or > button.

NIGHT MODE : Switch the NIGHT MODE ON or OFF with < or >

button.

Selecting the Night Mode ON is effective in Dolby

Digital only, and it compresses the dynamic

range.

This softens loud passages such as sudden

explosions, to help prevent disturbing others late

at night.

LFE LEVEL : Select the output level of the LFE signal included

in the Dolby Digital signal or the DTS signal.

Select 0dB, -10 dB or OFF with < or > button.

The level is ordinarily set to 0 dB. When use DTS

music source, LFE level is set to -10 dB.

CHANNEL LEVEL CONTROL

Desired channels can be selected by pressing ^ or v button.

Each channel level will be adjusted by pressing < or > button.

Only the usable channels which are determined depending on the

SURROUND mode, and SPEAKER SETTING are displayed.

MULTI ROOM SETUP

MULTI ROOM : To switch on the Multi-room output.

VIDEO : Select the video source of the Multi-room

output.

AUDIO : Select the audio source of the Multi-room

output.

VOLUME : Select whether the Multi-room output level

is variable or fixed.

VOLUME LEVEL : Adjust the Multi-room output level.

MAIN ROOM STATUS : Selected input source in the main room will

be displayed.

Notes:

If “VOLUME” is set to “FIXED”, the multi-room output level cannot

be adjusted.

You cannot transmit a digital signal using the multi-room function.

Any source component that is desired to be operated in the second

zone needs to have the analog outputs connected to receiver.

ENGLISH

BASIC OPERATION

LISTENING TO THE TUNER

MANUAL TUNING

1. To select the tuner as the source, press the TUNER button t on

the front panel or press the TUNER button , on the remote

control unit.

2. Press the TUNER button t on the front panel or press the

TUNER button , on the remote control unit to select the desired

frequency band if required.

3. Press the F/P button !6 on the front panel to display the frequency.

4. Press the TUNING/PRESET or button !5 on the front panel or

press the ^, v button ⁄0 on the remote control unit.

5. If FM is selected, press the MODE button !7 on the front panel or

select T-MOD by the Jog Dial n and press the ENT button m in

the TUNER mode on the remote controller.

(FM) MODE BUTTON OPERATION

When “AUTO” indicator is on in the display, FM stations that broadcast

in stereo will be received in stereo and the “STEREO” indicator lights.

When “AUTO” indicator is off, all the FM stations will be received in

mono regardless of whether or not they are broadcasting in stereo.

AUTO TUNING

1. Press the F/P button !6 on the front panel to display the frequency.

2. Press the TUNING/PRESET or button !5 on the front panel

for more than 1 second to start the Auto tuning function.

AUTO TUNING (USING THE REMOTE CONTROL UNIT)

Press ^, v button ⁄0 for more than 1 second to start the Auto tuning

function.

PRESET TUNING

With this unit you can preset up to 30 FM/AM (MW/LW) stations in any

order. For each station, you can memorize the frequency and

reception mode if desired.

1-a. Manual Presetting

1. Refer to the “MANUAL TUNING” or “AUTO TUNING” section

above to tune in a desired station.

2. Press the MEMORY button !4. “MEMORY” indicator starts blinking

on the display.

While “MEMORY” is still blinking (approx. 5 seconds), select the

preset number by pressing the TUNING/PRESET or button !5

then press the MEMORY button !4 again.

3. When a number has been properly input, “MEMORY” indicator

stops blinking and goes out.

The station is now stored in the specified preset memory location.

1-b. Manual Presetting (Using the remote unit)

1. Tune in a desired station.

2. Press the MEMO button ⁄6.

3. Enter the desired preset number with ten keypad ⁄7.

4. Then, press MEMO button ⁄6 again to store.

2. Auto Presetting

This function automatically scans the FM and AM (MW/LW) band and

enters all stations with sufficient signal strength into the memory.

1. Press and hold down the MEMORY button !4 and TUNER button

t simultaneously for 3 seconds or more.

2. “MEMORY“ will blink on the display.

3. Each time the tuner finds a station, the scanning will pause and

memory. Auto presetting will starts.

4. Operation stops automatically when all 30 preset memory

positions are filled or when auto scanning attains the highest end

of all bands.

To stop the auto preset function at anytime, press the CLEAR

button !3.

3. Recalling a Preset Station

1. Press the F/P button !6 to change the display to preset.

2. Select the desired preset station by pressing TUNING/PRESET

or button !5 on the front panel or press CH or CH button ⁄2

on the remote.

Note:

To directly access the preset stations using the numeric keypad,

select the desired preset station by entering one or two digits using

the numeric keypad ⁄7.

To return to the Manual Tuning mode, press the F/P button !6.

4. Preset Scan Tuning (Using the remote control unit)

1. Select the SCAN by the Jog Dial n and press the ENT button m

in the TUNER mode on the remote controller. (The preset station

with the smallest preset number is recalled first. If no stations have

been preset, “NO PRESET” shows in the display and the unit

returns to the previous mode.)

2. Preset stations are recalled in sequence (CH-1 → CH-2, etc.) for 5

seconds each. Preset numbers that do not contain stations are

skipped.

3. You can fast forward the preset stations by pressing the CH

button continuously.

When the desired preset station is received, cancel the preset scan

operation by pressing the CH button or the CLEAR button ⁄5.

5. Clearing Preset Stations

You can remove preset stations from memory using the following

procedure.

1. Recall the preset number to be cleared with the method described

in “Recalling” a preset station.

2. Press the CLEAR button !3 on the front panel or CLEAR button

⁄5 on the remote control unit for 3 seconds or more.

“CLEAR” appears on the display to indicate that the specified

preset number has been cleared.

6. Frequency Direct Call

1. Select F-DIR by the Jog Dial n and press the ENT button m in

the TUNER mode on the remote controller.

2. Display shows “FM– – –.––MHz” (at FM mode).

3. Input your desired frequency with tenkeypad buttons on the

remote controller.

Eg) 98.1 MHz

Press 9, 8, 1 and 0

4. Press the ENT button m again.

ENGLISH

STATION NAME PRESET (on PRESET display mode)

The station name preset function allows the name of each preset

channel to be entered using alphanumeric characters. The Station

Name button is valid only in the tuner mode. Before station name

preset operation, store stations with the preset memory operation.

1. Press the MEMORY button !4 on the front panel or MEMO button

⁄6 on the remote for more than 3 seconds.

2. The left most column of the station name indicator flashes,

indicating the character entry ready status.

[Operation (Using the SR7200)]

3. When you press the TUNING/PRESET or buttons !5 is

turned, alphabetic and numeric characters will be displayed in the

following order:

A → B → C ...Z → 1 → 2 → 3..... 0 → – → + → / → (Blank) → A

UP →

← DOWN

4. After selecting the first character to be entered, press the

MEMORY button !4. The entry in this column is fixed and the next

column starts to flash. Fill the next column and press the

MEMORY button !4 for more than 1 second to confirm the entry.

[Operation (Using the remote unit)]

First, press the TUNER button on the remote control unit.

(This operation is not necessary if the remote control unit has

already been operated in the TUNER mode.)

3. Enter the character using the ten keypad ⁄7. For example, to

enter “A”:

1) Press the “1” button. “A” appears on the display column.

2) Every time the 1 button is pressed, the displayed character

changes in the order: A → B → C → 1 → A...

Pressing buttons other than the “1” button cause different

characters to be displayed in a similar way, so that other

alphanumeric characters can be entered. To enter a blank or

space, press the “0” button.

4. When the desired character is displayed, press the MEMO button

⁄6 to confirm the entry in this column and move to the next

column. After having filled all of the 8 columns, press the MEMO

button ⁄6, for more than 1 second to confirm the entry.

RDS OPERATION

Now in use in many countries, RDS (Radio Data System) is a

description of the station’s programming hidden space in the FM

signal.

Your new receiver is equipped with RDS to assist in the selection of

FM stations using station and network names, rather than broadcast

frequencies. Additional RDS functions include the ability to search for

programme types.

RADIO TEXT

Some RDS stations broadcast RADIO TEXT, which is additional

information on the station and programme being broadcast.

RADIO TEXT information appears as ‘running’ text in the display.

RADIO TEXT is transmitted character-by- character by the radio

station. As a result of that it may take some time until the entire text

has been completely received.

RDS DISPLAY

When a receiver is tuned to an FM station that is transmitting RDS

data, the Front Panel Information Display will automatically show the

station name or RDS TEXT in place of the typical display of the

station’s broadcast frequency.

To change the display, select the DISP by the Jog Dial n and press

the ENT button m in the TUNER MODE on the remote controller.

PROGRAMME TYPE (PTY) DISPLAY

The RDS system categorizes programmes according to their genre

into different programme type (PTY) groups. To display the

programme type information of the current station, select the PTY by

the Jog Dial n and press the ENT button m in the TUNER MODE on

the remote controller.

PTY AUTO SEARCH

Your receiver is equipped to automatically search for stations

transmitting any of 29 different programme types. To search for a

PTY, follow these procedures:

1. Select the PTY button by the Jog Dial n and press the ENT

button m in the TUNER MODE on the remote controller. The

current station’s PTY will be displayed, or the currently selected

PTY group will be displayed in blinking if no station or RDS data is

present.

2. To change to a new PTY type, press the CH / button ⁄2 until the

desired PTY is shown in the display.

To select a specific PTY type, use the ten key pad ⁄7 on the

remote control to select the programme type corresponding to the

numbered choices in the table on the following.

3. Once the desired PTY group or type has been selected, select the

PTY by the Jog Dial n while the display blink (approx. 5

seconds). The PTY Auto search will start, and the tuner will pause

at each station broadcasting RDS PTY information corresponding

to the selected choice.

4. To advance to the next RDS station with the desired PTY, selcet

the PTY by the Jog Dial n again within 5 seconds.

NUMBER DISPLAY PROGRAMME TYPE

1 POP Pop Music

2 ROCK Rock Music

3 MOR M. O. R. Music

4 LIGHT Light classical

5 CLASSIC Serious classical

6 NEWS News

7 AFFAIR Current Affairs

8 INFO Information

9 SPORT Sport

10 EDUCATE Education

11 DRAMA Drama

12 CULTURE Culture

13 SCIENCE Science

14 OTHERS Varied

15 OTHER Other Music

16 WEATHER Weather

17 FINANCE Finance

18 CHILDREN Children’s programmes

19 SOCIAL Social Affairs

20 RELIGION Religion

21 PHONE IN Phone In

22 TRAVEL Travel

23 HOBBIES Hobbies

24 JAZZ Jazz Music

25 COUNTRY Country Music

26 NATION National Music

27 OLDIES Oldies Music

28 FOLK Folk Music

29 DOCUMENT Documentary

RT (

RADIO TEXT

)

PS (

Program Service Name

) Frequency

ENGLISH

OTHER FUNCTIONS

SETTING THE SLEEP TIMER

Set the sleep timer while the power is turned on.

1. Turn the power ON and press the SLEEP button o.

2. Press the SLEEP button o the number of times to set the desired

sleep time in minutes.

Each press of the SLEEP button o or changes the display in the

following order:

The unit will shut off in the number of minutes indicated.

* While the sleep timer is activated, the remaining time can be

displayed for approximately 2 seconds by pressing the SLEEP

button o.

* To cancel the sleep timer, press the SLEEP button o and then

press the CLEAR button !3.

TV AUTO ON/OFF FUNCTION

This function allows the component connected to the TV IN jack to

control the power (ON/OFF) to the SR7200.

AUTO POWER ON

1. Be sure TV auto mode is enable. (Refer page 10 : System Setup 1/3)

2. Connect your TV TUNER (etc) to the TV IN terminal.

Be sure to connect the video input.

3. Turn OFF the power to the TV TUNER and the SR7200 will be in

standby mode.

4. Turn ON the TV TUNER and tune in a receivable station.

5. When the station is received, the SR7200 turns ON and TV is

selected automatically.

AUTO POWER OFF

1. In the above situation, turn the TV TUNER OFF or select a

channel that does not contain any broadcast.

2. The SR7200 switches to STANDBY after approximately 5

minutes.

Note:

AUTO POWER OFF is canceled if the FUNCTION SELECTOR

button t is set to a source other than TV. The function reactivates

when TV is selected again.

Caution:

Some TV broadcasts may cause the TV AUTO FUNCTION to be

turned enable. To set this function to ENABLE/DISABLE, refer to

the SETUP MENU.

10 20 30

(OFF) 90 60

PLAYBACK OPERATION

NORMAL PLAYBACK

1. Press the POWER ON button on the remote.

2. Press the FUNCTION SELECTOR button t on the front panel or

press the FUNCTION button , on the remote unit to select an

input source.

3. Turn the SURROUND MODE SELECTOR knob e on the front

panel or Surround mode buttons ⁄7 in the AMP MODE on the

remote unit to select the desired surround mode.

4. Adjust the volume level using the VOLUME knob r on the front

panel or press the VOL / button . on the remote. If

necessary, adjust the tone, select the TRB+, TRB– and BAS+,

BAS– by the Jog Dial n and press ENT button m in the AMP

MODE on the remote unit.

Notes:

• In case of remote control operation, press one of the function

buttons twice within 2 seconds to select the function.

• Tone control is available for following surround modes.

AUTO (except 96 kHz), STEREO, DOLBY PRO LOGIC and DTS.

LISTENING TO A DIFFERENT AUDIO SOURCE WHILE

WATCHING A VIDEO SOURCE (Using the remote control

unit)

1. Select one of the following video sources

TV, DVD, VCR1, DSS/VCR2 or AUX.

2. Next, select one of the following audio sources

FM, AM (MW/LW), CD, TAPE, or CD-R/MD.

ENGLISH

ON SCREEN DISPLAY INFOMATION

The on-screen display, which can be activated by the Main unit or

remote, appears on the TV screen to show the current setting status of

the SR7200.

Note:

Each video input function is set PAL or NTSC for TV format of

OSD.

If this setup does not meet the video input signal, character of OSD

can not synchronize.

So You can select these format function by function.

Press OSD button ⁄7 on the remote controller for 3 seconds or

more. "PAL" or "NTSC" will be shown on the display of SR7200,

press OSD button ⁄7 again to change the TV format.

The indication on FL display will change " PAL" → " NTSC" →

"PAL"→.

This setup is memorized with each video input function.

1. GENERAL INFORMATION

When the OSD button ⁄7 is pressed, the current setting are displayed

on the TV monitor.

This display disappears automatically in about 5 seconds after the

button is pressed.

q VIDEO SOURCE:

Displays the current video source being selected with the function selector

TV, DVD, VCR1, DSS or AUX.

w AUDIO SOURCE:

Displays the current audio source being selected with the function selector

FM, AM (MW, LW), CD, TAPE, CD-R, TV, DVD, VCR1, DSS or AUX.

e DIGITAL INPUT:

Displays the digital input that you are using

DIG-1, DIG-2, DIG-3, DIG-4 or DIG-5.

r SURROUND MODE:

Displays the current surround mode

AUTO, STEREO, 6CH STEREO, VIRTUAL, MATRIX, STADIUM,

HALL, MOVIE, CS5.1, 6.1 CH SURR, PLO LOGIC, PLII MUSIC,

PLII MOVIE, DTS

t MULTI ROOM

Displays the current status of the Multi Room function, ON or OFF.

y MASTER VOLUME

Displays the current volume level.

The volume level is higher at the right of the display.

Note:

The On-Screen Display signals for the main room can be output

from the TV MONI composite video (RCA) output and the TV

MONI, S-Video and TV MONI component video output jacks.

With some video equipment or software, the On-Screen Display

characters may be distorted due to noise or tracking adjustment

error.

MULTI ROOM SELECTOR

The Multi Room Selector is a function which allows you to listen to the

same or a different source in a room other than the room in which the

SR7200 is located. To use this function, a multi room remote unit and

remote control signal receiver available from your Marantz dealer are

necessary. The operations possible with the multi room function are

explained briefly below. For details, refer to the instruction manual

supplied with the multi room remote control unit and receiver.

MULTI ROOM SELECTOR OPERATION

1. Press the MULTI ROOM button !1. The unit enters multi room

mode and the display indicates “SEL SOURCE” and flashes the

“MULTI ROOM” indicator for approx. 5 seconds. In this time, you

can select the input source by pressing the FUNCTION

SELECTOR button t.

2. Then, the display indicates “M/VOL xx dB”. At this time, you can

set the volume level of the multi room by turning the volume

control knob.

3. Then, the display indicates “MULTI PAL”. At this time, you can set

PAL or NTSC for second zone TV format of OSD. Press OSD

button ⁄7 on the remote control unit. “MULTI PAL” or “MULTI

NTSC” will be shown on the display of SR7200.

4. Then, the display indicates “M/SLEEP OFF” and you can set

sleep timer for multi room by pressing by the SLEEP button o.

Note:

If the multi room function is to be set using the remote control unit,

select the settings on the MULTI ROOM SETUP screen in the OSD

MAIN MENU. (Refer to page 12.)

MULTI ROOM SELECTOR OPERATION (USING THE MULTI

ROOM REMOTE CONTROL UNIT)

1. If Video output for multi room is connected to the TV in your

second zone, the on screen display for this video signal will be

shown as follow.

2. Press the POWER ON button, or select the desired source on

multi room remote control unit from the MULTI ROOM. Any of

these operations will put the SR7200 into multi room mode and

“MULTI ROOM” indicator will light and OSD system for the TV in

the multi room will be shown.

3. Press the VOL.UP or VOL.DOWN button on the multi room

remote control unit to set the desired sound volume.

4. In multi room mode, the multi room remote control unit can be

used in the multi room to operate the following functions.

You can select a tuner preset channel and tuning up or down, and

direct selection. And you can control the CD player, DVD player

VCR and tape deck connected to the SR7200.

5. Additionally, SLEEP timer function for multi room is available from

second zone, by pressing the SLEEP button on the multi room

remote control unit.

6. The status of the main room setting can be monitored from the

second zone with the OSD.

Caution:

If the main room and the secondary room are listening to the tuner,

the main room will have priority over controlling that source. For

example, you cannot change the frequency or preset of the Tuner

from a remote location if the main room is also listening to that

source.

La pagina si sta caricando...

Marantz SR7200 Manuale utente

Marca: Marantz

Modello: SR7200

Categoria: Ricevitori AV

Tipo: Manuale utente

Scarica PDF

rapporto

in altre lingue

English: Marantz SR7200 User manual

Marantz SR7200 Manuale utente

Marantz SR7200 Manuale utente

in altre lingue

Documenti correlati

Altri documenti