Senao Networks U2M-ZF7731 Manuale utente

Ruckus Wireless

®

ZoneFlex

®

7731 802.11n

Outdoor Point to Point Bridge

Getting Started Guide

Part Number 800-70236-001

Published September 2009

www.ruckuswireless.com

i

1 About This Getting Started Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2 Unpacking the ZoneFlex Wireless Bridge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Mounting Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Bottom Cover and Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3 Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Prepare the Required Hardware and Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Get to Know the Hardware Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

LED Colors and What They Mean . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Push Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

External Antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

4 Preparing the Wireless Bridge Pair for Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

What You Will Need . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Configure the Root Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Step 1: Connect the Power and Ethernet Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Step 2: Prepare the Administrative Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Step 3: Connect the Wireless Bridge to the Admin Computer . . . . . . . . . . . . . . . . . 16

Step 4: Log In to the Web Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Step 3: Ensure Network and Wireless Settings are Correct . . . . . . . . . . . . . . . . . . . . 18

Step 4: Change the IP Address (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Configure the Non-Root Bridge (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Step 5: Test the Link Between the Bridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Step 6: Disconnect the Wireless Bridge from the Administrative Computer . . . . . . 22

Step 7: Restore the Administrative Computer’s Network Settings . . . . . . . . . . . . . . 22

5 Physical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Prepare the Required Hardware and Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Perform a Site Survey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Determine the Optimal Mounting Location and Orientation . . . . . . . . . . . . . . . . . . . . 25

Contents

ii

Become Familiar with the Installation Components . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Decide How You Will Supply Power to the Wireless Bridge . . . . . . . . . . . . . . . . . . . . . 27

6 Deploying the Wireless Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Step 1: Complete the Power Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Step 2: Install the Back Panel Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Step 3: Connect the Wireless Bridge to the Network . . . . . . . . . . . . . . . . . . . . . . . . . . 33

7 Attaching the Mounting Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

What You Will Need . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Step 1: Attach the Static Bracket to the Mounting Surface . . . . . . . . . . . . . . . . . . . . . 35

Attaching the Bracket to a Flat Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Attaching the Bracket to a Pole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Step 2: Attach the Dynamic Bracket to the Wireless Bridge . . . . . . . . . . . . . . . . . . . . . 40

8 Mounting the Wireless Bridge. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

9 Mounting and Connecting the External Antennas (Optional) . . . . . . . . . . . . . . . . . . . . . 44

10 Aiming the Bridge Pair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

11 Verifying the Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

12 What to Do Next. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Change the Administrative Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Configure the Security Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Using FlexMaster to Manage the Wireless Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Read Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

1

1 About This Getting Started Guide

This Getting Started Guide provides information on how to set up the Ruckus Wireless

ZoneFlex 7731 802.11n Outdoor AP/Point to Point Wireless Bridge on your network. Topics

covered in this guide include installation, basic configuration, and device mounting.

This guide is intended for use by those responsible for installing and setting up network

equipment. Consequently, it assumes a basic working knowledge of local area networking,

wireless networking, and wireless devices.

Related Documentation

In addition to this guide, each Ruckus Wireless ZoneFlex 7731 802.11n Outdoor AP/Point

to Point Bridge documentation set includes the following:

■ User Guide: Provides detailed information on how to configure the Wireless Bridge.

The User Guide is available for download on the Ruckus Wireless Support Web site at:

http://support.ruckuswireless.com/documents

■ Release Notes: Provides late-breaking information about the current software release,

including new features, enhancements, and known issues. If the information in the

Release Notes differs from the information in this guide, follow the instructions in the

Release Notes.

■ Online Help: Accessible from the ZoneFlex 7731 Web interface, the Online Help

provides information that helps you configure the device from the Web interface.

2

Unpacking the ZoneFlex Wireless Bridge

Package Contents

2 Unpacking the ZoneFlex Wireless Bridge

1. Open the Wireless Bridge package, and then carefully remove the contents.

2. Return all packing materials to the shipping box, and put the box away in a dry location.

3. Verify that all items listed in Package Contents

below are included in the package.

Check each item for damage. If any item is damaged or missing, notify your authorized

Ruckus Wireless sales representative.

NOTE: The ZoneFlex 7731 Outdoor AP/Bridge standard package includes a pair of

ZoneFlex 7731 devices (a root bridge and a non-root bridge). Two sets of mounting and

power accessories are included, along with one set of user documentation.

Package Contents

The ZoneFlex 7731 Wireless Bridge package contains two ZoneFlex 7731 units and two

sets of accessories (one for each unit). It should contain all of the items listed below:

■ One ZoneFlex 7731 Outdoor Point to Point Wireless Bridge (labeled “Root Bridge”)

■ One ZoneFlex 7731 Outdoor Point to Point Wireless Bridge (labeled “Non-Root

Bridge”)

■ Two PoE injector boxes (excluded in some SKUs)

■ Two power adapter boxes (SW DC48V/0.42A AC100-240V) for the PoE injector

(excluded in some SKUs)

■ Two mounting kits (see “Mounting Kit Contents” for details)

■ Two bags containing bottom Wireless Bridge cover and related accessories (see

“

Bottom Cover and Accessories” for details)

■ Service Level Agreement / Limited Warranty Statement

■ Regulatory Statement

■ This Getting Started Guide

WARNING: The Ruckus Wireless PoE injector and power adapter (if supplied with your

Wireless Bridge) are for indoor use only. Never mount the PoE injector and power adapter

outdoors with the Wireless Bridge.

3

Unpacking the ZoneFlex Wireless Bridge

Package Contents

Mounting Kit Contents

■ Dynamic bracket

■ Static bracket

■ Steel clamps (2 pieces)

■ Machine screws (8 pieces)

■ Hex bolts (4 pieces)

■ Split lock washers (4 pieces)

■ Flat washers (4 pieces)

■ Split lock washers (4 pieces)

■ Machine screws (8 pieces)

■ Thumb screws (2 pieces)

■ Wall anchors (2 pieces)

Figure 1. Mounting kit contents

Dynamic bracket Static bracket Steel clamps (2 pieces)

Hex bolt (4 pieces) Flat washer (4 pieces) Split lock washer (4 pieces)

Thumb screws (2 pieces) Machine screw (8 pieces) Wall anchor with metal cone

and hex nut (2 pieces)

4

Unpacking the ZoneFlex Wireless Bridge

Package Contents

Bottom Cover and Accessories

Each bottom cover accessory bag contains:

■ Bottom cover of the Wireless Bridge

■ DC terminal block

■ 20mm x 30mm sealing strips (2 pieces)

■ Sealing plug

■ White P-clip cable clamp (2 pieces)

■ Machine screws (2 pieces)

■ Machine screws with washers (3 pieces)

Figure 2. Bottom cover and accessory package contents

Bottom cover DC terminal block Sealing Plug Sealing Strips (2

pieces)

White P-clip cable

clamp

Machine screw (2

pieces)

Machine screw with

washer (3 pieces)

5

Before You Begin

Prepare the Required Hardware and Tools

3 Before You Begin

Prepare the Required Hardware and Tools

You must supply the following tools and equipment:

■ A notebook computer running Windows 2000/XP/Vista and installed with one wireless

802.11b/g network card and one Ethernet card

■ 6mm flathead screwdriver

■ 6mm Phillips screwdriver

■ 10mm ratchet wrench

■ 3mm Phillips screwdriver (if you will be using DC power)

■ Electric drill with 8mm drill bit (if mounting on a flat surface)

NOTE: At the beginning of each procedure, this guide lists the specific tools, accessories,

and equipment that you will need to complete the procedure.

Get to Know the Hardware Features

Figure 3 and Figure 5 identify the Wireless Bridge features that are relevant to the

installation and mounting instructions that this guide provides. Before you begin the

installation process, Ruckus Wireless recommends that you become familiar with these

features.

6

Before You Begin

Get to Know the Hardware Features

Figure 3. Wireless Bridge LEDs and bottom connectors

5

1

2

4

3

7

Before You Begin

Get to Know the Hardware Features

Table 1. LEDs and bottom panel connectors

No Label Description

1 LEDs See “

LED Colors and What They Mean” below for more

information.

2 RJ45 LAN port that supports Power over Ethernet (PoE) and 10/

100/1000 Mbps network connections

3 Reset Using a pointed object (for example, a pen), press this

button to restart the Wireless Bridge or to restore it to

factory default settings:

• To restart the Wireless Bridge, press the Reset button

once.

• To restore the Wireless Bridge to factory default, press

the Reset button for six (6) seconds.

WARNING: Restoring the Wireless Bridge to factory

default settings removes all configuration changes that

you have made. These include the IP address, password,

access control list, and wireless settings. Returning the

configuration of these features to their factory default

settings may result in network connectivity issues.

4 12V DC In addition to PoE, you can also use direct current or DC

(from a battery, for example) to supply power to the

Wireless Bridge.

5 Aiming Button Press this button to set the Wireless Bridge to Aiming

Mode. When Aiming Mode is set, the LEDs can be used

to determine signal strength. See “

Aiming Mode” for

more information.

8

Before You Begin

Get to Know the Hardware Features

LED Colors and What They Mean

The ZoneFlex 7731 Wireless Bridge includes 6 dual color LEDs. The LEDs function in two

modes, normal operation mode and aiming mode.

Figure 4. LED Indicators

■ For Normal Operation Mode LED states and what they indicate, refer to Tab le 2.

■ For Aiming Mode LED states and what they indicate, refer to Tab l e 3.

Normal Operation Mode

Table 2. Normal Operation Mode LED indicators

LED Meaning

LED 1 (AIM/PWR) Solid Green = Power on

Off = Power off

LED 2 (LAN) Solid Green = Link Up

Blinking Green = Activity

Off = Link Down

LED 3 (WLAN) Solid Green = Associated

Blinking Green = Not Associated

Off = Radio Off

LED 4 (ROLE) Solid Yellow = This unit is the root bridge

Off = This unit is the non-root bridge

LED 5 & 6 (P0 and P1) Alternating Blinking = Provisioning in process

Simultaneous Blinking = Provisioning complete;

reboot pending

LED 1

LED 2

LED 3

LED 4

LED 5

LED 6

9

Before You Begin

Get to Know the Hardware Features

In Normal Operation Mode, the LED indicators are off when disconnected, flashing green

while connecting and solid green when a connection has been established.

In Aiming Mode, LED 1 indicates that the Wireless Bridge is in Aiming Mode. LED

indicators 2 - 6 are used together to indicate signal strength, and should be read from

bottom to top (the higher the LEDs go, the stronger the signal).

Aiming Mode

In Aiming Mode, each LED has three states to represent different values. Solid yellow

indicates the highest value, flashing yellow indicates medium value and off indicates the

lowest value. If all six LEDs are solid yellow, the Wireless Bridge has the strongest signal

possible. If some LEDs are flashing yellow or off, reposition the Wireless Bridge to achieve

a better signal.

Push Buttons

The ZoneFlex 7731 includes two push buttons:

■ A recessed factory default reset button

■ A large blue Aiming Mode button that sets the bridge to Aiming Mode

To reset the unit to its factory defaults, press and hold the Reset button for six (6) seconds.

Press and hold the blue Aiming button for four (4) seconds to initiate aiming between the

root and non-root bridge.

CAUTION: Resetting the ZoneFlex 7731 to its factory defaults will result in loss of all

configuration settings, including the pre-provisioning (pairing of the root and non-root

bridge) settings that were enabled prior to shipping. If you do need to reset to defaults,

you will need to re-provision the pair.

Table 3. Aiming Mode LED indicators

LED Meaning

LED 6 Signal strength 5

LED 5 Signal strength 4

LED 4 Signal strength 3

LED 3 Signal strength 2

LED 2 Signal strength 1

LED 1 (AIM/PWR) Solid Yellow = Aiming Mode

Solid Green = Normal Operation Mode

Off = Off

10

Before You Begin

Get to Know the Hardware Features

External Antennas

The ZoneFlex 7731 Outdoor Wireless Bridge includes one purpose designed internal

directional antenna. If you want to extend the range of your wireless network, you can

connect two external high gain antennas to the standard N-type external antenna

connectors on the top panel of the Wireless Bridge. The antennas must have a gain of less

than 23dBi to comply with FCC and CE regulations. For more information, refer to

“

Mounting and Connecting the External Antennas (Optional)” on page 44.

Figure 5. The antenna connectors are protected by metal caps

Metal Cap

11

Preparing the Wireless Bridge Pair for Installation

What You Will Need

4 Preparing the Wireless Bridge Pair for

Installation

This section describes the procedures for setting up the bridge pair before you begin the

physical installation.

ZoneFlex 7731 Outdoor Point to Point Bridges come in pre-provisioned pairs. One is

designated as the “Root Bridge” and one is designated the “Non-Root Bridge.” There-

fore, in most situations, you should not need to manually provision the pair. If you do need

to provision (after restoring factory default settings, for example), see the ZoneFlex 7731

User Guide available on the Ruckus Wireless Support Web site for detailed instructions.

The default IP addresses for the root and non-root bridge are as follows:

■ Root Bridge: 192.168.2.1

■ Non-Root Bridge: 192.168.2.254

If you want to assign different IP addresses for either or both units, see “

Step 4: Change

the IP Address (Optional)” on page 19.

A summary of the steps in this section is below:

1. Connect Ethernet and power to both units.

2. Access the units using an administration computer.

3. Ensure network and wireless settings are correct.

4. Change the IP address (optional).

5. Use the SpeedFlex tool built into the Web interface to test the link between the units.

What You Will Need

Before starting with the configuration task, make sure that you have the following require-

ments ready:

■ An administrative computer (notebook computer) running Microsoft Windows Vista/

XP/2000

■ Mozilla Firefox 2.0 (or later) or Microsoft Internet Explorer 6.0 (or later) installed on the

administrative computer

■ One 5.6mm-6.0mm (outside diameter) Cat5e foil screened twisted pair (FTP) solid

■ cable

■ Two Ethernet cables

■ PoE injector (if not supplied with the Wireless Bridge, you can purchase a third party

802.3af-compliant PoE injector or switch)

■ 6mm Phillips screwdriver

If you are planning to power the Wireless Bridge using a 12v DC connection, you will also

12

Preparing the Wireless Bridge Pair for Installation

Configure the Root Bridge

need the following:

■ One 3.1mm-3.3mm UL1185 (80°, 300V) single shielded DC cable

■ 12v DC, 1A DC power source (for example, a battery)

■ 3mm Phillips screwdriver

Configure the Root Bridge

Step 1: Connect the Power and Ethernet Cables

The procedure for connecting cables to the Wireless Bridge depends on the power source

that you will be using. You can do one of the following:

■ Use Power Over Ethernet

■ Use DC Power

NOTE: You only need to connect one type of power source at this point, even if you are

planning to use both PoE and DC power in your final deployment.

Use Power Over Ethernet

1. Take out the PoE injector and the power adapter from the Wireless Bridge package.

2. Obtain two Ethernet cables.

3. Connect one end of one Ethernet cable to the AP/BRIDGE port on the PoE injector,

and then connect the other end to the RJ45 port on the ZoneFlex 7731.

4. Connect one end of the other Ethernet cable to the NETWORK port on the PoE

injector.

5. Connect the power jack to the DC 48V IN connector on the PoE injector, and then

plug the power adapter into a power source. The single LED on the PoE injector turns

green.

6. Check the power LED on the ZoneFlex 7731 to ensure power is being supplied to the

bridge.

13

Preparing the Wireless Bridge Pair for Installation

Configure the Root Bridge

Figure 6. Connect the Ethernet cables and power adapter to the PoE injector

You have completed connecting the Wireless Bridge to a PoE power source.

Use DC Power

To use DC to power the Wireless Bridge, you need to connect a DC cable (not supplied

with the Wireless Bridge) to the DC terminal block.

1. Take out the DC terminal block from the small plastic bag that contains the bottom

cover of the Wireless Bridge.

2. Connect the DC cable’s ground wire to V- terminal. If you are looking at the terminal

block with the wiring terminal screws on top, the V- terminal is on the left side.

3. Connect the DC cable’s +12v DC wire to the V+ terminal. If you are looking at the

terminal block with the wiring terminal screws on top, the V+ terminal is on the right

side.

Figure 7. Connect the ground wire to the V- terminal and the +12v DC wire to the V+

terminal

To Adm in

Computer

To Bridge

To AC P ow er Source

Ground Wire to

V- Terminal

12V DC Wire to

V+ Terminal

14

Preparing the Wireless Bridge Pair for Installation

Configure the Root Bridge

4. Using a 3mm Phillips screw, tighten the wiring terminal screws. Screw torque value must

be 4kg-5kg.

5. Connect the DC terminal block to the 12V DC port on the Wireless Bridge.

Figure 8. Connect the DC terminal block to the 12V DC port

6. Connect the DC cable to a DC power source (for example, a battery).

You have completed connecting the Wireless Bridge to a DC power source.

Step 2: Prepare the Administrative Computer

NOTE: The following procedure is applicable if the administrative computer is running

Windows XP or Windows 2000. If you are using a different operating system, refer to the

documentation that was shipped with your operating system for information on how to

modify the computer’s IP address settings.

1. On your Windows XP or Windows 2000 computer, open the Network Connections (or

Network and Dial-up Connections) control panel according to how the Start menu is

set up:

• On Windows XP, click Start > Control Panel > Network Connections.

• On Windows 2000, click Start > Settings > Network Connections.

15

Preparing the Wireless Bridge Pair for Installation

Configure the Root Bridge

2. When the Network Connections window appears, right-click the icon for Local Area

Connection, and then click Properties.

NOTE: Make sure that you configure the Local Area Connection properties, not the

Wireless Network Connection properties.

3. When the Local Area Connection Properties dialog box appears, select Internet

Protocol (TCP/IP) from the scrolling list, and then click Properties. The Internet

Protocol (TCP/IP) Properties dialog box appears.

4. Write down all of the currently active network settings. You will need this information

later when you restore your computer to its current network configuration.

5. Click Use the following IP address, and then configure the IP address settings with

the values listed in Table 4

. For a sample configuration, refer to Figure 9.

You can leave the Alternate DNS server box blank.

6. Click OK to save your changes and close the TCP/IP Properties dialog box.

7. Click OK again to close the Local Area Connection Properties dialog box.

Windows saves the IP address settings that you have configured.

Table 4. Configure your computer’s IP address settings

IP address 192.168.2.22 (or any address in the 192.168.2.x

network—with the exception of 192.168.2.1, which

is already used by the bridge)

Subnet mask 255.255.255.0

Default gateway 192.168.2.1

Preferred DNS server 192.168.2.1

16

Preparing the Wireless Bridge Pair for Installation

Configure the Root Bridge

Figure 9. Sample configuration in the Internet Protocol (TCP/IP) Properties dialog box

Step 3: Connect the Wireless Bridge to the Admin

Computer

If you have not already done so, connect the admin computer to the ZoneFlex 7731 using

an Ethernet cable, or two Ethernet cables and a PoE injector if you are using Power over

Ethernet (see “

Connect the Ethernet cables and power adapter to the PoE injector” on

page 13

).

Step 4: Log In to the Web Interface

1. Open a Web browser window from the admin computer.

2. In the address or location bar, type the following address:

Root Bridge: http://192.168.2.1

Non-Root Bridge: http:/192.168.2.254

3. Press <Enter> on the keyboard to connect to the Wireless Bridge’s Web interface. A

security alert message appears.

4. Click Yes or OK (depending on the browser) to continue. The Wireless Bridge’s login

page appears.

La pagina sta caricando ...

Senao Networks U2M-ZF7731 Manuale utente

Questo manuale è adatto anche per

Senao Networks U2M-ZF7731 Manuale utente

in altre lingue

Documenti correlati

Altri documenti