SY-D6IBA2
Motherboard
Quick Start Guide
FC
C
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
POST CONSUMER
RECYCLED PAPER
100%
Hardware
Installation
Quick BIOS
Setup
Introduction
SCSI Utilities
The SOYO CD
SOYO™
2
SY-D6IBA2 Motherboard
Single or Dual Pentium
®
III & Pentium
®
II processors
supported
82440 BX AGP/PCI Motherboard
66&100MHz Front Side Bus supported
ATX Form Factor
Copyright © 1999 by Soyo Computer Inc.
Trademarks:
Soyo is a registered trademark of Soyo Computer Inc. All trademarks are the property of their
owners.
Product Rights:
Product and corporate names mentioned in this publication are used for identification purposes
only and may be registered trademarks or copyrights of their respective companies.
Copyright Notice:
All rights reserved. This manual is copyrighted by Soyo Computer Inc. You may not reproduce,
transmit, transcribe, store in a retrieval system, or translate into any language, in any form or by
any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, any part of
this publication without express written permission of Soyo Computer Inc.
Disclaimer:
Soyo Computer Inc. makes no representations or warranties regarding the contents of this
manual. We reserve the right to revise the manual or make changes in the specifications of the
product described within it at any time without notice and without obligation to notify any
person of such revision or change. The information contained in this manual is provided for
general use by our customers. Our customers should be aware that the personal computer field is
the subject of many patents. Our customers should ensure that their use of our products does not
infringe upon any patents. It is the policy of Soyo Computer Inc. to respect the valid patent rights
of third parties and not to infringe upon or assist others to infringe upon such rights.
Restricted Rights Legend:
Use, duplication, or disclosure by the Government is subject to restrictions set forth in
subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at
252.277-7013.
About This Guide:
This Quick Start Guide is for assisting system manufacturers and end users in setting up and
installing the Motherboard. Information in this guide has been carefully checked for reliability;
however, no guarantee is given as to the correctness of the contents. The information in this
document is subject to change without notice.
If you need any further information, please visit our Web Site on the Internet. The address is
"http://www.soyo.com.tw".
D6IBA2 Serial - Version 1.0 - Edition: April 1999
* These specifications are subject to change without notice
SY-D6IBA2
Quick Start Guide
3
Introduction
1
1
Introduction
Congratulations on your purchase of the
SY-D6IBA2
Motherboard. This Quick Start Guide
describes the steps for installing and setting up your new Motherboard.
This guide is designed for all users to provide the basic steps of Motherboard setting and
operation. For further information, please refer to SY-D6IBA2 Motherboard User's Guide and
Technical Reference online manual included on the CD-ROM packed with your
Motherboard.
Unpacking
* If your board comes with a driver disc and a paper manual, the Quick Start Guide and the CD-ROM are not included in the package.
When unpacking the Motherboard, check for the following items:
u
The SY-D6IBA2 82440 BX AGP/PCI Motherboard
u
This Quick Start Guide
u
The Installation CD-ROM
u
Three SCSI Driver Installation Diskettes
labeled “7800 Family Manager Set V3.01” (optional)
u
Two CPU Retention sets
u
One IDE Device Flat Cable
u
One Floppy Disk Drive Flat Cable
u
One 50-pin Narrow SCSI Cable (optional)
u
One 68-pin Wide SCSI Cable (optional)
u
One 68-pin Ultra2 SCSI Cable (optional)
SY-D6IBA2
Quick Start Guide
4
Introduction
SY-D6IBA2 Motherboard Layout
Key Features
Ø
Supports Intel Pentium
®
III processor (450-
550MHz) & Pentium
®
II processor (233-
450MHz)
Ø
Easy CPU settings in BIOS with the
“SOYO COMBO Setup”
Ø
Auto-detect CPU voltage
Ø
SCSI port onboard (optional)
Ø
PC98, APM, Ultra DMA/33
Ø
Power-on by modem or alarm
Ø
Supports onboard hardware monitoring
and includes Hardware Doctor™ utility
Ø
Supports Wake-On-LAN (WOL)
Ø
Supports Power-On by PS/2 Keyboard
Ø
Supports Creative SB-LINK™ (PC-PCI)
for PCI audio card
Ø
1 x 32-bit AGP slot
Ø
4 x 32-bit bus mastering PCI slots
Ø
2 x USB ports
Ø
1 x IrDA port
Ø
Supports multiple-boot function
Ø
ATX power connector
Ø
Power failure resume
(PC-PCI)
COM 1
COM 2
USB 1
PRT
USB 2
PS/2 KB
Connector
PS/2 Mouse
Connector
ISA Slot #1
ISA Slot #2
Intel
82371 EB
Intel
82443 BX
IR1
1
5
Ultra
I/O Chipset
AGP Slot
ATX
Power
1
FDC
IDE 2
1
DIMM 1
DIMM 2
DIMM 3
DIMM 4
Flash BIOS
W83781D
828AC
SB-LINK
JP5
CMOS Clear
Jumper
3
1
JP4
JP7
3
1
JP1
1
3
WOL
Header
FAN1
CPUFAN
1
FAN2
CPUFAN
1
FAN3
1
1
IDE 1
PCI Slot #1
PCI Slot #2
PCI Slot #3
PCI Slot #4
1
(Optional)
Slot 1 #2
Slot 1 #1
Narrow SCSI (50-pin)
PWRBT
HDD LED
Turbo
LED
Reset
_
+
_
+
_
+
_
+
Speaker
Keylock
Power
LED
3V
Lithium
Battery
Wide SCSI (68-pin)
1
(Optional)
Ultra2 SCSI (68-pin)
1
(Optional)
JP44
1
3
adaptec
AQWA741
(Optional)
AIC - 7890AB
Winbond
Adaptec
83977EF-AW
AIC-3860
Hardware Monitoring
Winbond
W83781D
SCSI HDD
LED
SY-D6IBA2
Quick Start Guide
5
Hardware
Installation
2
2
Installation
To avoid damage to your Motherboard, follow these simple rules while
handling this equipment:
l
Before handling the Motherboard, ground yourself by grasping an unpainted portion
of the system's metal chassis.
l
Remove the Motherboard from its anti-static packaging. Hold it by the edges and
avoid touching its components.
l
Check the Motherboard for damage. If any chip appears loose, press carefully to seat
it firmly in its socket.
Follow the directions in this section designed to guide you through a quick and correct
installation of your new
SY-D6IBA2
Motherboard. For detailed information, please refer to
SY-D6IBA2 Motherboard User's Guide and Technical Reference online manual included on
the CD-ROM packed with your Motherboard.
PREPARATIONS
Gather and prepare all the necessary hardware equipment to complete the installation
successfully:
u
Slot 1 processor with built-in CPU cooling fan (boxed type)
u
SDRAM module
u
Computer case and chassis with adequate power supply unit
u
Monitor
u
PS/2 Keyboard
u
Pointing Device (PS/2 Mouse)
u
VGA Card
u
Sound Card (optional)
u
Speaker(s) (optional)
u
Disk Drives: HDD, CD-ROM, Floppy drive…
u
External Peripherals: Printer, Plotter, and Modem (optional)
u
Internal Peripherals: Modem and LAN cards (optional)
SY-D6IBA2
Quick Start Guide
6
Hardware
Installation
Install the Motherboard
Follow the steps below in order to perform the installation of your new
SY-D6IBA
Motherboard.
Step 1. Install the CPU
:
Record the working frequency of your CPU that should be clearly marked on the CPU cover.
FSB 66MHz
266MHz (66 x 4.0) 333MHz (66 x 5.0) 400MHz (66 x 6.0)
300MHz (66 x 4.5) 366MHz (66 x 5.5) 433MHz (66 x 6.5)
FSB 100MHz
350MHz (100 x 3. 5) 450MHz (100 x 4.5) 550MHz (100 x 5.5)
400MHz (100 x 4.0) 500MHz (100 x 5.0) 600MHz (100 x 6.0)
Notice 1:
When installing two processors, please make sure the front side bus and working
frequency are identical for both processors.
Notice 2:
If you are using a single processor, preferably install the processor in Slot 1 #1,
leaving Slot 1 #2 empty for future expansion to dual CPU.
Retention Module Step 1. Open the two sides by folding them up.
Step 2.
Push the locks on top of the CPU
inward.
Step 3. Insert the CPU into the retention
module. The CPU fits in the CPU slot in
only ONE way, do not try to force it in.
Step 4. After completely inserting the CPU, push the two locks on
top of the CPU outward. Now your CPU is ready for use.
To remove the CPU, press
the two notches on top of
the CPU inward. Now
press the two slides on the
retention module down and
remove the CPU.
SY-D6IBA2
Quick Start Guide
7
Hardware
Installation
Note: Installing a heat sink and cooling fan on top of your CPU is necessary for
proper heat dissipation. Failing to install these items may result in overheating
and possible burn-out of your CPU.
Step 2. Make Connections to the Motherboard
This section tells how to connect internal peripherals and power supply to the Motherboard.
Internal peripherals include IDE devices (HDD, CD-ROM), Floppy Disk Drive, Chassis Fan,
Front Panel Devices (Turbo LED, Internal Speaker, Reset Button, IDE LED, and KeyLock
Switch.), Wake-On-LAN card, VGA card, Sound Card, and other devices.
For more details on how to connect internal and external peripherals to your new SY-
D6IBA2 Motherboard, please refer to SY-D6IBA2 Motherboard User's Guide and Technical
Reference online manual on CD-ROM.
Connectors and Plug-ins
PCI Audio Card Header: SB-Link™ (PC-PCI) Wake-On-LAN Header: JP44
Pin1 Pin2 Pin3
Connect the SB-Link™ (PC-PCI) cable from your PCI audio
card to this header.
5VSB GND MP-Wakeup
Slot 1 #1 CPU
Cooling Fan: FAN 1
Slot 1 #2 CPU
Cooling Fan: FAN 2
Chassis Fan: FAN 3
Pin1 Pin2 Pin3 Pin1 Pin2 Pin3 Pin1 Pin2 Pin3
GND 12V SENSOR GND 12V SENSOR GND 12V SENSOR
Power LED Keylock
Pin1 Pin2 Pin3
Pin1 Pin2
5V NC GND
Control Pin GND
Speaker
Pin1 Pin2 Pin3 Pin4
5V NC NC Speaker out
HDD LED Turbo LED PWRBT RESET
Pine1 Pin2 Pin1 Pin2
Pin1 Pin2
Pin1 Pin2
LED Anode
LED
Cathode
LED
Cathode
GND
Power
On/Off
GND
Power
Good
GND
IrDA (Infrared Device Header): IR1
Pin1 Pin2 Pin3 Pin4 Pin5
VCC None IRRX GND IRTX
ATX Power On/Off: PWRBT ATX Power Supply: ATX PW
Connect your power switch to this
header (momentary switch type).
To turn off the system,
please press this switch and hold
down for longer than
4 seconds.
Attach the ATX Power cable to this connector.
When using the Power-On by PS/2 Keyboard
function, please make sure the ATX power supply
can take at least 720mA load on the 5V Standby lead
(5VSB) to meet the standard ATX specifications.
Power LED
Key Lock
Speaker
Reset
PWRBT
Turbo LED
HDD LED
+
+
++
_ _
_
_
SY-D6IBA2
Quick Start Guide
8
Hardware
Installation
Step 3. Configure Memory
Your board comes with four DIMM sockets, providing support for up to 1GB of main memory
using DIMM modules from 8MB to 256MB. For 66MHz front side bus CPUs use 12ns or faster
memory; for 100MHz front side bus CPUs use 8ns (100MHz, PC100 compliant) memory.
Memory Configuration Table
Number of
Memory Modules
DIMM 1 DIMM 2 DIMM 3 DIMM 4
1 1
st
2 1
st
2
nd
3 1
st
2
nd
3
rd
4 1
st
2
nd
3
rd
4
th
RAM Type SDRAM
Memory Module
Size (MB)
8/16/32/64/128/256 Mbytes
Notice 1: 256 MB memory modules only available on PC registered DIMM.
Notice 2: Always install memory modules in the order prescribed in this table.
Notice 3: Do not install unbuffered and registered memory modules together.
Important:
It is of prime importance that you install DIMM modules as outlined in the table
above in order to preserve signal integrity on 100MHz front side bus systems.
Step 4. Set the CPU Frequency
You do not need to set any jumper for the CPU frequency. Instead, CPU settings are
changed through the BIOS
[SOYO COMBO SETUP].
Please refer to Chapter 3 - Quick
BIOS Setup for details on how to set the Pentium
®
II processor frequency.
Step 5. Enable/Disable Power-On by PS/2 Keyboard (JP1)
You can choose to enable the Power-On by PS/2 Keyboard function by shorting pin 2-3 on
jumper JP1, otherwise, short pin 1-2 to disable this function.
Support Power-On
by Keyboard
Enable Disable
JP1 Setting
Enable Power-On
by PS/2 Keyboard
(short pin 2-3)
Disable Power-On
by PS/2 Keyboard
(short pin 1-2)
Important: When using the Power-On by PS/2 Keyboard function, please make sure
the ATX power supply can take at least 720mA load on the 5V Standby lead (5VSB)
to meet the standard ATX specifications.
3
2
1
3
2
1
SY-D6IBA2
Quick Start Guide
9
Hardware
Installation
Step 6. Power Button Enable (JP7)
Your system can be power on by either pressing a power button or typing in a password,
which can be set in the BIOS SOYO COMBO Setup. To avoid being unable to power up the
system due to of forgetting the password, you can place a jumper cap to short JP7. This will
always enable the Power Button.
Power Button
Enable
Power Button always
enabled
Power Button according to
BIOS setting
JP7 Setting
Short pin to always
enable the Power
Button.
Open pin for a Power
Button function according
to the BIOS setting.
Step 7. Clear CMOS Data (JP5)
Clear the CMOS memory by momentarily shorting pin 2-3 on jumper JP5 for at least 5
seconds, and then by shorting pin 1-2 to retain new settings. This jumper can be easily
identified by its white colored cap.
CMOS Clearing Retain CMOS Data Clear CMOS Data
JP5 Setting
Short pin 1-2 to retain
the new settings.
Short pin 2-3 for
at least 5 seconds
to clear the CMOS.
Note: You must unplug the ATX power cable from the ATX power connector when
performing the CMOS Clear operation.
3
2
1
3
2
1
SY-D6IBA2
Quick Start Guide
10
Hardware
Installation
Note on Over-clocking Capability
The SY-D6IBA2 Motherboard provides over-clocking capability. Due to the over-clocking
setting your system may fail to boot up or hang during run time. If this occurs, please perform
the following steps to recover your system from the abnormal situation:
1.
Turn off system power. (If you use an ATX power supply, and depending on your
system, you may have to press the power button for more than 4 seconds to shut
down the system.)
2.
Press and hold down the <Insert> key while turning on the system power. Keep
holding down the <Insert> key until you see the message of the CPU type and
frequency (133MHz or 200MHz) appear on screen.
3.
Press the <Del> key during the system diagnostic checks to enter the Award BIOS
Setup program.
4.
From the BIOS main menu, select [SOYO COMBO SETUP] and move the cursor to
the [CPU Frequency] field to set the proper working frequency.
5.
Select [Save & Exit SETUP] and press <Enter> to save the configuration to the
CMOS memory, and continue the boot sequence.
Note
:
SOYO does not guarantee system stability if the user over clocks the system.
Any malfunctions due to over-clocking are not covered by the warranty.
SY-D6IBA2
Quick Start Guide
11
Quick BIOS
Setup
3
3
Quick BIOS Setup
This Motherboard does not use any hardware jumpers to set the CPU frequency. Instead,
CPU settings are software configurable with the BIOS
[SOYO COMBO SETUP].
The
[SOYO COMBO SETUP] menu combines the main CPU parameters that you need to
configure, all in one menu, for a quick setup in BIOS.
After the hardware installation is complete, turn the power switch on, then press the
<DEL>
key
during the system diagnostic checks to enter the Award BIOS Setup program. The CMOS
SETUP UTILITY will display on screen. Then, follow these steps to configure the CPU settings.
Step 1. Select [LOAD SETUP DEFAULT]
Select the “LOAD SETUP DEFAULT” menu and type “Y” at the prompt to load the BIOS
optimal setup.
Step 2. Select [STANDARD CMOS SETUP]
Set [Date/Time] and [Floppy drive type], and then set [Hard Disk Type] to “Auto”.
Step 3. Select [SOYO COMBO SETUP]
Move the cursor to the
[CPU Speed]
field to set the CPU working frequency.
Available [CPU Speed] settings on your SY-D6IBA2 Motherboard are detailed in the
following table. If you set this field to [Manual], you are then required to fill in the next two
consecutive fields: (1) the CPU Host Clock, and (2) the CPU Ratio.
CPU Frequency
233MHz (66 x 3.5) 350MHz (100 x 3.5)
266MHz (66 x 4.0) 400MHz (100 x 4.0)
300MHz (66 x 4.5) 450MHz (100 x 4.5)
333MHz (66 x 5.0) 500MHz (100 x 5.0)
366MHz (66 x 5.5) 550MHz (100 x 5.5)
400MHz (66 x 6.0) 600MHz (100 x 6.0)
433MHz (66 x 6.5)
Select the working frequency of
your Pentium
®
III, Pentium
®
II
processor among these preset
values.
Note: Mark the checkbox that
corresponds to the working
frequency of your Pentium
®
III,
Pentium
®
II processor in case the
CMOS configuration should be lost.
Step 4. Select [SAVE & EXIT SETUP]
Press
<Enter>
to save the new configuration to the CMOS memory, and continue the boot
sequence.
SY-D6IBA2
Quick Start Guide
12
The SOYO CD
4
4
The SOYO CD
Your SY-D6IBA2 Motherboard comes with a CD-ROM labeled "SOYO CD." The SOYO CD
contains the user's manual file for your new Motherboard, the drivers software available for
installation, and a database in HTML format with information on SOYO Motherboards and
other products.
Step 1. Insert the SOYO CD into the CD-ROM drive
The SOYO CD will auto-run, and the SOYO CD Start Up Menu will display as shown below.
(SOYO CD Start Up Program Menu)
The SOYO CD Start Up Program automatically detects which SOYO Motherboard you own
and displays the corresponding model name.
Step 2. Read SOYO [D6IBA2] Manual
Click the
Read Manual
button to open the user's manual file of your Motherboard.
SY-D6IBA2
Quick Start Guide
13
The SOYO CD
Please note that if the Start Up program was unable to determine which SOYO Motherboard
you own, the manual selection menu will pop up, as shown below. Then select the user's
manual file that corresponds to your Motherboard model name and click
OK.
(Manual Selection Menu)
The user's manual files included on the SOYO CD can be read in PDF (Postscript
Document) format. In order to read a PDF file, the appropriate Acrobat Reader software
must be installed in your system.
Note:
The Start Up program automatically detects if the Acrobat Reader utility is already
present in your system, and otherwise prompts you on whether or not you want to install it.
You must install the Acrobat Reader utility to be able to read the user's manual file. Follow
the instructions on your screen during installation, then once the installation is completed,
restart your system and re-run the SOYO CD.
Step 3. Install Drivers
Click the
Install Drivers
button to display the list of drivers software that can be installed with
your Motherboard. The Start Up program displays the drivers available for the particular
model of Motherboard you own. We recommend that you only install those drivers.
SOYO CD Manuals
Please select your manual in the box below
and click OK.
686 boards: 586 boards:
OK Back
D6IBA2
SY-D6IBA2
Quick Start Guide
14
The SOYO CD
The following drivers are available for Windows 95
(Driver Installation Menu)
The following drivers are available for Windows 98
(Driver Installation Menu)
However, to display the list of all drivers software available with SOYO Motherboards, click
the
Display all drivers on the SOYO CD
button. Please make sure to install only the
drivers adapted to your system, or otherwise this cause system malfunctions.
Please select the driver you want to install and click OK, You will have to
restart your system after installation. Only the drivers that are relevant
to your board are displayed initially.
Intel Southbridge Drivers
Intel BusMaster Drivers for Win95
SOYO Speedpro BusMaster Driver for win 95/98
Intel BusMaster Drivers for Win NT
Intel BusMaster Drivers for OS/2
Winbond hardware doctor for win 95/98
SOYO CD Xpress utility
Cancel
Display all drivers
on the SOYO CD
OK
Driver Installation
Please select the driver you want to install and click OK, You will have to
restart your system after installation. Only the drivers that are relevant
to your board are displayed initially.
SOYO Speedpro BusMaster Driver for win 95/98
Intel BusMaster Drivers for Win NT
Intel BusMaster Drivers for OS/2
Winbond hardware doctor for win 95/98
SOYO CD Xpress utility
Cancel
Display all drivers
on the SOYO CD
OK
Driver Installation
SY-D6IBA2
Quick Start Guide
15
The SOYO CD
A short description of all available drivers follows:
Ø Intel Southbridge Drivers
Because Windows 95 does not recognize the Southbridge of the newer Intel chipsets (TX,
BX, ZX etc) this utility has to be run, it will update the necessary Windows files. (Only for
Windows 95)
Ø SOYO SpeedPro Busmaster Driver for Win 95/98
Without the busmaster drivers the CPU will need to be involved every time data is read from
or written to the Harddisk. The busmaster drivers make use of DMA (Direct Memory Access)
to relieve the CPU of this burden, thus speeding up the system.
The SOYO SpeedPro driver makes use of an advanced caching algorithm, which gives it an
advantage over other busmaster drivers.
Ø Intel Busmaster Drivers for Windows 95
Ø Intel Busmaster Drivers for Win NT
Ø Intel Busmaster Drivers for OS/2
These are the official busmaster drivers as supplied by Intel.
Note: Do NEVER install two types of busmaster drivers on your system, this will
lead to conflicts and system instability. Therefore, if you install the SOYO
SpeedPro Busmaster driver you can NOT install the Intel Busmaster drivers.
Before installing a new busmaster driver first UNINSTALL the old busmaster
driver.
Ø SOYO CD Xpress Utility
This utility will enhance your CD-ROM Drive data-thoughput by using space on the Harddisk
as cache. This way application programs can access data faster. This utility is suitable for
Windows 95/98.
Ø Winbond hardware doctor for Windows xx
Your motherboard comes with a hardware monitoring IC. By installing this utility Temperature,
Fan speed and Voltages can be monitored. It is also possible to set alarms when current
system values exceed or fall below pre-set values.
This utility comes with a preset monitoring rage for the CPU voltage. However, the core voltage
of the processor you purchased may fall out of this preset range, so you may need to adjust the
pre-set value. Please refer to the SY-D6IBA2 Motherboard’s CD manual for the details.
Select which driver you want to install and click
OK,
or click
Cancel
to abort the driver
installation and return to the main menu.
Note 1:
Once you have selected a driver, the system will automatically exit the SOYO CD to
begin the driver installation program. When the installation is complete, most drivers require
to restart your system before they can become active.
SY-D6IBA2
Quick Start Guide
16
The SOYO CD
Note 2: EZ-SCSI Utility:
The SCSI utility for use with the onboard Adaptec
®
SCSI chip is
located in the \drivers\EZ-SCSI directory. EZ-SCSI is suitable for DOS or Windows 3.1
environment only. The manual file in PDF format can be found at the following location:
\Manual\EZ-SCSI.pdf.
Step 4. Check the Latest Releases
Click the 'Check the latest Releases' button to go the SOYO Website to automatically find
the latest BIOS, manual and driver releases for your motherboard. This button will only work
if your computer is connected to the internet through a network or modem connection. Make
sure to get your modem connection up before clicking this button.
Step 5. Enter the SOYO CD
Click the
Enter SOYO CD
button to enter the SOYO HTML database. The Start Up
program will activate the default HTML browser installed on your system (for example,
Internet Explorer or Netscape) to visualize the contents of the SOYO CD.
The SOYO CD contains useful information about your Motherboard and other SOYO
products available. For your convenience, this information is available in HTML format,
similar to the format widely used on the Internet.
(SOYO CD HTML Database in English*)
Note:
If no HTML browser is installed on your system, the Start Up program will prompt you
on whether or not you would like to install the Internet Explorer* browser. Click YES to install
the HTML browser. After the installation is complete, please restart your system. Then re-run
the SOYO CD and you will be able to browse the SOYO HTML database.
(* Internet Explorer is a Microsoft Trademark)
SY-D6IBA2
Quick Start Guide
17
SCSI Utilities
5
5
SCSI Utilities
Ultra2 SCSI I/O Subsystem
Your new
SYD6IBA2
high-performance Motherboard is equipped with the onboard
Adaptec
®
AIC-7890 Ultra2 SCSI host adapter for your high bandwidth applications, providing
data transfer rates of up to 80 Mbytes per second. The Ultra2 SCSI is an input/output bus
interface that provides a powerful multitasking interface between your computer’s PCI bus
and your SCSI devices.
With SCSI, you can connect a variety of devices on your computer (Hard/Floppy Disk Drives,
CD-ROM Drives, Scanners, Tape Drives, Removable Media Drives, etc.) in a daisy-chain
topology to a common host adapter. Daisy-chaining SCSI devices allows them to
communicate with each other by sending commands and data via the SCSI bus.
The AIC-7890 Ultra2 SCSI provides maximum data transfer rates of 20 Mbytes/sec in the
narrow 8-bit mode (Fast SCSI) and 40 Mbytes/sec in the wide 16-bit mode (Ultra SCSI), and
80 Mbytes/sec in the LVD mode (Ultra2 SCSI)
Installing SCSI Devices
Your Motherboard features two internal SCSI connectors onboard, and comes with one 50-
pin flat cable, one 68-pin flat cable, and one 68-pin Ultra2 cable.
50-pin Fast SCSI Connector
Narrow SCSI allows data transfer rates of up to 20 Mbytes/sec. With Narrow SCSI, you can
connect up to 7 internal Fast SCSI devices to the 50-pin Fast SCSI connector on the
Motherboard. Use the enclosed Narrow SCSI cable to connect up to 2 internal SCSI
devices.
If you are connecting more than 2 internal SCSI devices, you must use an internal SCSI
cable with enough connectors to accommodate all your devices. Contact your dealer for
special cable service.
When Fast SCSI devices are connected to the bus, the total length of all cables is not to
exceed 3 meters (9.8 ft.) to ensure reliable operation.
50-pin internal connector
Fast SCSI
SY-D6IBA2
Quick Start Guide
18
SCSI Utilities
68-pin Ultra-Wide SCSI Connector
Ultra-Wide SCSI allows you to connect up to 15 devices (7 Narrow internal and 8 Wide
internal or external SCSI devices, or 15 Wide internal or external SCSI devices) to the 68-pin
Ultra-Wide SCSI connector on the Motherboard. Devices that connect to the 16-bit Wide
SCSI bus can transfer data at the maximum rate of 40 Mbytes/sec.
68-pin Ultra2 SCSI Connector
Ultra2 SCSI allows you to connect up to 15 devices (LVD/SE mode) to the 68-pin Ultra2
SCSI connector on the Motherboard. Devices that connect to the 16-bit Ultra2 SCSI bus can
transfer data at the maximum rate of 80 Mbytes/sec.
Connecting Internal SCSI Devices
If you are connecting several internal SCSI devices (more than 2 SCSI devices), make sure
you have an internal SCSI cable with enough connectors to accommodate all of your
devices. The enclosed SCSI flat cables can serve up to 2 SCSI devices.
Follow these steps to ensure a proper installation of your internal SCSI devices:
1.
Prepare each SCSI devices for installation; configure the device
SCSI ID
and
terminators (
terminate
the last internal device attached to the cable by setting its
termination to the ON position; all other internal devices on the SCSI bus must have
their termination set to OFF).
2.
Install the SCSI devices in your computer.
3.
Plug the connector at one end of the internal SCSI cable into the host adapter’s SCSI
connector on the Motherboard.
Note:
Make sure the cable’s colored stripe is aligned with pin-1 of the host adapter’s
connector. Pin-1 of the SCSI connector is usually designated by a small triangle (
5
), or a
“1” at one corner of the connector.
4.
Connect the remaining connectors on the cable to the SCSI devices (CD-ROM drives,
etc.).
Note:
Make sure the cable’s colored stripe is aligned with pin-1 of the SCSI device’s
connector.
5.
Connect a DC power cable (from your computer’s power supply) to the power
connector on each SCSI device.
68-pin internal connector
Ultra-Wide SCSI
68-pin internal connector
Ultra2 SCSI
SY-D6IBA2
Quick Start Guide
19
SCSI Utilities
SCSI Driver Installation
Windows
®
95 Users
This chapter explains how to install the Adaptec 7800 Family Manager Set aic78xx.mpd and aic78u2.mpd
drivers for Windows 95. The aic78xx.mpd driver supports all Adaptec7800 Family Ultra2 SCSI (and earlier)
host adapters, and the aic78u2.mpd driver supports all Ultra2 SCSI adapters. Refer to the list.
If you are performing a first time Windows 95 installation, see Installing the Driver When Installing Windows
95 If Windows 95 is already installed in your system, see Installing the Driver When Windows 95 is Already
Installed.
Note: When Windows 95 starts, if a New Hardware Found dialog is displayed after your
7800 Family Manager Set host adapter has been installed, you must select the Driver from
Disk Provided by Hardware Manufacturer option. Insert your Adaptec 7800 Family
Manager Set v. 3.01 diskette into the floppy drive and type a:\win95 as the path. Then,
follow the on screen instructions.
Installing the Driver When Installing Windows 95
A version of the aic78xx.mpd (Ultra2 SCSI) driver is embedded (included) in the Windows 95 installation
CD-ROM. During a normal Windows 95 installation, the 7800 Family host adapter (Ultra2 SCSI or earlier) is
detected in your system and the embedded aic78xx.mpd driver is automatically installed.
Note: If the Windows 95 installation cannot detect the 7800 Family host adapter(Ultra2
SCSI or earlier) installed in your computer, or you are installing the aic78u2.mpd driver for
an Ultra2 SCSI host adapter, you must install the driver manually after Windows 95 is
complete. Follow the procedures in the section Installing the Driver When Windows 95 is
Already Installed, below
Installing the Driver When Windows 95 is Already Installed
To update or install the aic78xx.mpd or aic78u2.mpd if Windows 95 is already installed, follow these
instructions:
SY-D6IBA2
Quick Start Guide
20
SCSI Utilities
Note: All Adaptec 7800 Family Ultra2 SCSI (and earlier) host adapters use the
aic78xx.mpd driver. Ultra2 SCSI adapters use the aic78u2.mpd driver. Once the correct
driver is updated, it is not necessary to update it again for each 7800 Family host adapter
installed in your system.
1. Start Windows 95.
2. Click the [Start] button on the Windows 95 task bar, and then point to Settings.
3. Click [Control Panel].
4. Double-click the [System] icon.
5. On the Device Manager tab, click the plus sign (+) next to the SCSI controller icon.
Note: If Windows 95 cannot determine the type of host adapter installed in your
computer, a yellow question mark labeled Other devices appears instead of the JSCSI
controller icon. To continue, click the plus sign (+) next to the question mark; a yellow
question mark labeled PCI SCSI Bus Controller then appears.
6. Double-click the 7800 Family host adapter you wish to update, or if a yellow question mark labeled
PCI SCSI Bus Controller is displayed, double-click the question mark.
7. Insert the Adaptec 7800 Family Manager Set v.3.01 diskette into drive A.
8. Select the Drives tab
Note: If the version of Windows 95 you are using displays an Update Drivers button
instead of a [Change Driver] button, follow the procedures in the section Updating the
Driver for Windows 95 (Version OSR2).
9. Click [Change Driver]. If you are prompted to select the hardware type, select [SCSI Controller].
10. Click the [Have Disk] button and enter a:\win95 as the path.
11. Click [OK]
12. Select the 7800 Family host adapter, and click [OK].
13. Click [OK]. The driver is copied and scanned.
14. You must restart your computer for the changes to take effect. Click [Yes] to restart your computer.
Click [No] to return to the system properties window.
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
SOYO MOTHERBOARD SY-D61BA2 Manuale utente
- Tipo
- Manuale utente
in altre lingue
Documenti correlati
Altri documenti
-
Adaptec AAA-131U2 Manuale utente
-
-
Yamaha WF192 Getting Started
-
HP Adaptec U160 SCSI Adapter Guida d'installazione
-
-
Tyan S2881 Manuale utente
-
EPOX EP-6ZXM Manuale utente
-
-
-