SY-6IEB
Motherboard
Quick Start Guide
FC
C
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
POST CONSUMER
RECYCLED PAPER
100%
Hardware
Installation
Quick BIOS
Setup
Introduction
Onboard Sound
Driver Installation
The SOYO CD
SOYO™
2
SY-6IEB Motherboard
Pentium
®
II processor & Celeron
TM
processor
82440 EX/LX AGP/PCI Motherboard
66MHz Front Side Bus supported
AT Form Factor
Copyright © 1998 by Soyo Computer Inc.
Trademarks:
Soyo is a registered trademark of Soyo Computer Inc. All trademarks are the property of their
owners.
Product Rights:
Product and corporate names mentioned in this publication are used for identification purposes
only and may be registered trademarks or copyrights of their respective companies.
Copyright Notice:
All rights reserved. This manual is copyrighted by Soyo Computer Inc. You may not reproduce,
transmit, transcribe, store in a retrieval system, or translate into any language, in any form or by
any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, any part of
this publication without express written permission of Soyo Computer Inc.
Disclaimer:
Soyo Computer Inc. makes no representations or warranties regarding the contents of this
manual. We reserve the right to revise the manual or make changes in the specifications of the
product described within it at any time without notice and without obligation to notify any
person of such revision or change. The information contained in this manual is provided for
general use by our customers. Our customers should be aware that the personal computer field is
the subject of many patents. Our customers should ensure that their use of our products does not
infringe upon any patents. It is the policy of Soyo Computer Inc. to respect the valid patent rights
of third parties and not to infringe upon or assist others to infringe upon such rights.
Restricted Rights Legend:
Use, duplication, or disclosure by the Government is subject to restrictions set forth in
subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at
252.277-7013.
About This Guide:
This Quick Start Guide is for assisting system manufacturers and end users in setting up and
installing the Motherboard. Information in this guide has been carefully checked for reliability;
however, no guarantee is given as to the correctness of the contents. The information in this
document is subject to change without notice.
If you need any further information, please visit our Web Site on the Internet. The address is
"http://www.soyo.com.tw".
6IEB Serial - Version 2.0 - Edition: March 1999
* These specifications are subject to change without notice
SY-6IEB
Quick Start Guide
3
Introduction
1
1
Introduction
Congratulations on your purchase of the
SY-6IEB
Motherboard. This Quick Start Guide
describes the steps for installing and setting up your new Motherboard.
This guide is designed for all users to provide the basic steps of Motherboard setting and
operation. For further information, please refer to SY-6IEB Motherboard User's Guide and
Technical Reference online manual included on the CD-ROM packed with your
Motherboard.
Unpacking
* If your board comes with a driver disc and a paper manual, the Quick Start Guide and the CD-ROM are not included in the package.
When unpacking the Motherboard, check for the following items:
u
The SY-6IEB 82440 EX/LX AGP/PCI Motherboard
u
This Quick Start Guide
u
The Installation CD-ROM
u
The CPU Retention Set
u
One IDE Device Flat Cable
u
One Floppy Disk Drive Flat Cable
u
One 9-pin serial connector with 9-pin flat cable and 6-pin
PS/2 mouse connector with 6-pin cable
u
One 25-pin parallel connector with 25-pin flat cable and 9-
pin serial connector with 9-pin flat cable
1
Flash BIOS
1
W83781D
SY-6IEB
Quick Start Guide
4
Introduction
SY-6IEB Motherboard Layout
Key Features
Ø
Supports Intel Pentium
®
II
processors (233-333MHz) &
Celeron™ processors (266-433MHz)
Ø
Auto-detect CPU voltage
Ø
PC98, APM, ACPI, Ultra DMA/33
Ø
Power-on by modem or alarm
Ø
SOYO COMBO Setup
Ø
Supports Wake-On-LAN (WOL)
Ø
Power-on by Keyboard
Ø
Supports Creative SB-LINK™ (PC-PCI)
for PCI audio card
Ø
1 x 32-bit AGP slot
Ø
3 x 32-bit bus mastering PCI slots
Ø
2 x USB ports
Ø
1 x IrDA port
Ø
Supports multiple-boot function
Ø
Y2K Complaint
Ø
AT & ATX power connectors
IDE 1
1
IDE 2
1
ISA Slot #2
1
3V
Lithium
Battery
PCI Slot #3
JP44
1
3
Intel
82371 EB
Intel
82443 EX
SB-LINK
(PC-PCI)
CPUFAN
1
CHAFAN
1
JP5
31
CMOS Clear
Jumper
AGP Slot
ITE8671
I/O Chipset
Flash BIOS
SPEAKER
Reset
Power
LED
Key
Lock
PWRBT
Turbo
LED
HDD
LED
_
+
_
+
_
+
_
+
1
5
IR
Slot 1 for
Pentium II
Processor
R
AT Power
Flash BIOS
1
FDC
ATX
Power
JP10
3
1
KB
Connector
PS/2 Mouse
Connector
COM 2
1
COM 1
1
LPT
1
USB
1
DIMM 1
DIMM 2
PCI Slot #2
PCI Slot #1
ISA Slot #1
SY-6IEB
Quick Start Guide
5
Hardware
Installation
2
2
Installation
To avoid damage to your Motherboard, follow these simple rules while
handling this equipment:
l
Before handling the Motherboard, ground yourself by grasping an unpainted portion
of the system's metal chassis.
l
Remove the Motherboard from its anti-static packaging. Hold it by the edges and
avoid touching its components.
l
Check the Motherboard for damage. If any chip appears loose, press carefully to seat
it firmly in its socket.
Follow the directions in this section designed to guide you through a quick and correct
installation of your new
SY-6IEB
Motherboard. For detailed information, please refer to SY-
6IEB Motherboard User's Guide and Technical Reference online manual included on the
CD-ROM packed with your Motherboard.
PREPARATIONS
Gather and prepare all the necessary hardware equipment to complete the installation
successfully:
u
Slot 1 processor with built-in CPU cooling fan (boxed type)
u
SDRAM module
u
Computer case and chassis with adequate power supply unit
u
Monitor
u
PS/2 Keyboard
u
Pointing Device (PS/2 Mouse)
u
VGA Card
u
Speaker(s) (optional)
u
Disk Drives: HDD, CD-ROM, Floppy drive…
u
External Peripherals: Printer, Plotter, and Modem (optional)
u
Internal Peripherals: Modem and LAN cards (optional)
SY-6IEB
Quick Start Guide
6
Hardware
Installation
Install the Motherboard
Follow the steps below in order to perform the installation of your new
SY-6IEB
Motherboard.
Step 1. Install the CPU
Mark your CPU Frequency:
Record the working frequency of your CPU
that should be clearly marked on the CPU cover.
FSB 66MHz
266MHz (66 x 4.0) 333MHz (66 x 5.0) 400MHz (66 x 6.0)
300MHz (66 x 4.5) 366MHz (66 x 5.5) 433MHz (66 x 6.5)
CPU Mount Procedure:
To mount the processor that you have purchased
separately, follow these instructions.
Retention Module Step 1. Open the two sides by folding them up.
Step 2.
Push the locks on top of the CPU
inward.
Step 3. Insert the CPU into the retention
module. The CPU fits in the CPU slot in
only ONE way, do not try to force it in.
Step 4. After completely inserting the CPU, push the two locks on
top of the CPU outward. Now your CPU is ready for use.
To remove the CPU, press
the two notches on top of
the CPU inward. Now
press the two slides on the
retention module down and
remove the CPU.
Note: Installing a heat sink and cooling fan on top of your CPU is necessary for proper heat dissipation.
Failing to install these items may result in overheating and possible burn-out of your CPU.
SY-6IEB
Quick Start Guide
7
Hardware
Installation
Step 2. Make Connections to the Motherboard
This section tells how to connect internal peripherals and power supply to the Motherboard.
Internal peripherals include IDE devices (HDD, CD-ROM), Floppy Disk Drive, Chassis Fan,
Front Panel Devices (Turbo LED, Internal Speaker, Reset Button, IDE LED, and KeyLock
Switch.), Wake-On-LAN card, VGA card, Sound Card, and other devices.
For more details on how to connect internal and external peripherals to your new SY-6IEB
Motherboard, please refer to SY-6IEB Motherboard User's Guide and Technical Reference
online manual on CD-ROM.
Connectors and Plug-ins
PCI Audio Card Header: SB-Link™(PC-PCI) Wake-On-LAN Header: JP44
Pin1 Pin2 Pin3Connect the SB-Link™ (PC-PCI) cable from your
PCI audio card to this header.
5VSB GND MP-Wakeup
CPU Cooling Fan: CPUFAN Chassis Fan: CHAFAN
Pin1 Pin2 Pin3 Pin1 Pin2 Pin3
GND 12V SENSOR GND 12V SENSOR
Power LED Keylock
Pin1 Pin2 Pin3
Pin1 Pin2
5V NC GND
Control Pin GND
Speaker
Pin1 Pin2 Pin3 Pin4
5V NC NC Speaker out
HDD LED Turbo LED PWRBT RESET
Pin1 Pin2 Pin1 Pin2 Pin1 Pin2 Pin1 Pin2
LED Anode
LED
Cathode
LED
Cathode
GND
Power
On/Off
GND Power Good GND
IrDA (Infrared Device Header): IR1
AT Power Cable
Pin1 Pin2 Pin3 Pin4 Pin5
VCC None IRRX GND IRTX
Connect the AT Power cable to this
connector. If you use AT power supply.
ATX Power On/Off: PWRBT ATX Power Supply: ATX PW
Connect your power switch to this
header (momentary switch type).
To turn off the system,
please press this switch and
hold down for longer than
4 seconds.
Attach the ATX Power cable to this connector. If
you use ATX power supply.
When using the Keyboard Wake-Up
function, please make sure the ATX
power supply can take at least 720mA
load on the 5V Standby lead (5VSB) to
meet the standard ATX specifications.
1
1
1
11
1
1
Power LED
Key Lock
Speaker
Reset
PWRBT
Turbo LED
HDD LED
SY-6IEB
Quick Start Guide
8
Hardware
Installation
Step 3. Configure Memory
Your board comes with two DIMM sockets, providing support for up to 256MB of main
memory using DIMM modules from 8MB to 128MB with no restriction on memory
configuration. Therefore, you can install memory modules in any combination.
Memory Configuration
DIMM Banks
MEMORY
CONFIGURATION
DIMM 1 DIMM 2
RAM Type
EDO/SDRAM EDO/SDRAM
RAM Module Size (MB) 8/16/32/64/128 8/16/32/64/128
Note : There are two types of DIMM modules with different operating voltages:
3.3V and 5.0V. Please note that only 3.3V EDO DIMM modules can be used
on this Motherboard.
Step 4. Set the CPU Frequency
You do not need to set any jumper for the CPU frequency. Instead, CPU settings are
changed through the BIOS
[SOYO COMBO SETUP].
Please refer to Chapter 3 - Quick
BIOS Setup for details on how to set the Pentium
®
II processor frequency.
Step 5. Enable/Disable the Keyboard Wake-Up (JP10)
You can choose to enable the Wake-Up by Keyboard or Mouse function by shorting pin 1-2
on jumper JP1, otherwise, short pin 2-3 to disable this function.
Support Wake-Up
by Keyboard
Enable Disable
JP10 Setting
Enable Wake-up
by Keyboard
function
(short pin 1-2)
Disable Wake-up
by Keyboard
function
(short pin 2-3)
Important: When using the Keyboard Wake-Up function, please make sure the ATX
power supply can take at least 720mA load on the 5V Standby lead (5VSB) to meet the
standard ATX specifications.
3
2
1
3
2
1
SY-6IEB
Quick Start Guide
9
Hardware
Installation
Step 6. Clear CMOS Data (JP5)
Clear the CMOS memory by momentarily shorting pin 2-3 on jumper JP5 for at least 5
seconds, and then by shorting pin 1-2 to retain new settings. This jumper can be easily
identified by its white colored cap.
CMOS Clearing Retain CMOS Data Clear CMOS Data
JP5 Setting
Short pin 1-2 to retain
the new settings.
Short pin 2-3 for
at least 5 seconds
to clear the CMOS.
Note: You must unplug the AT/ATX power cable from the AT/ATX power connector
when performing the CMOS Clear operation.
Note on Over-clocking Capability
The SY-6IEB provides over-clocking capability. Due to the over-clocking setting your system
may fail to boot up or hang during run time. Please perform the following steps to recover
your system from the abnormal situation :
1.
Turn off system power.
2.
Press and hold down the <Insert> key while turning on the system power. Keep holding
down the <Insert> key until you see the message of the CPU type and frequency shown
on the screen.
3.
Press the <Del> key during the system diagnostic checks to enter the Award BIOS Setup
program.
4.
Select [SOYO COMBO SETUP] and move the cursor to the [CPU Frequency] field to set
the proper working frequency.
5.
Select [Save & Exit SETUP] and press <Enter> to save the new configuration to the
CMOS memory, and continue the boot sequence.
Note: SOYO does not guarantee system stability if the user over clocks the system.
Any malfunctions due to over-clocking are not covered by the warranty.
3
2
1
3
2
1
SY-6IEB
Quick Start Guide
10
Quick BIOS
Setup
3
3
Quick BIOS Setup
This Motherboard does not use any hardware jumpers to set the CPU frequency. Instead,
CPU settings are software configurable with the BIOS
[SOYO COMBO SETUP].
The
[SOYO COMBO SETUP] menu combines the main CPU parameters that you need to
configure, all in one menu, for a quick setup in BIOS.
After the hardware installation is complete, turn the power switch on, then press the
<DEL>
key
during the system diagnostic checks to enter the Award BIOS Setup program. The CMOS
SETUP UTILITY will display on screen. Then, follow these steps to configure the CPU settings.
Step 1. Select [LOAD SETUP DEFAULT]
Select the “LOAD SETUP DEFAULT” menu and type “Y” at the prompt to load the BIOS
optimal setup.
Step 2. Select [STANDARD CMOS SETUP]
Set [Date/Time] and [Floppy drive type], then set [Hard Disk Type] to “Auto”.
Step 3. Select [SOYO COMBO SETUP]
Move the cursor to the
[CPU Speed]
field to set the CPU working speed.
Available [CPU Speed] settings on your SY-6IEB Motherboard are detailed in the following
table. If you set this field to [Manual], you are then required to fill in the next two consecutive
fields: (1) the CPU Ratio, and (2) the CPU Frequency.
CPU Speed
233MHz (66x3.5) 366MHz (66x5.5)
266MHz (66x4.0) 400MHz (66x6.0)
300MHz (66x4.5) 433MHz (66x6.5)
333MHz (66x5.0)
Select the working frequency of your
Pentium
®
II, or Celeron processor
among these preset values.
Note: Mark the checkbox that
corresponds to the working frequency of
your Pentium
®
II, or Celeron processor
in case the CMOS configuration should
be lost.
Step 4. Select [SAVE & EXIT SETUP]
Press
<Enter>
to save the new configuration to the CMOS memory, and continue the boot
sequence.
SY-6IEB
Quick Start Guide
11
Hardware
Installation
4
4
The SOYO CD
Your SY-6IEB Motherboard comes with a CD-ROM labeled "SOYO CD." The SOYO CD
contains the user's manual file for your new Motherboard, the drivers software available for
installation, and a database in HTML format with information on SOYO Motherboards and
other products.
Step 1. Insert the SOYO CD into the CD-ROM drive
The SOYO CD will auto-run, and the SOYO CD Start Up Menu will display as shown below.
(SOYO CD Start Up Program Menu)
The SOYO CD Start Up Program automatically detects which SOYO Motherboard you own
and displays the corresponding model name.
Step 2. Read SOYO [6IEB] Manual
Click the
Read Manual
button to open the user's manual file of your Motherboard.
SY-6IEB
Quick Start Guide
12
Onboard Sound
Driver Installation
Please note that if the Start Up program was unable to determine which SOYO Motherboard
you own, the manual selection menu will pop up, as shown below. Then select the user's
manual file that corresponds to your Motherboard model name and click
OK.
(Manual Selection Menu)
The user's manual files included on the SOYO CD can be read in PDF (Postscript
Document) format. In order to read a PDF file, the appropriate Acrobat Reader software
must be installed in your system.
Note:
The Start Up program automatically detects if the Acrobat Reader utility is already
present in your system, and otherwise prompts you on whether or not you want to install it.
You must install the Acrobat Reader utility to be able to read the user's manual file. Follow
the instructions on your screen during installation, then once the installation is completed,
restart your system and re-run the SOYO CD.
Step 3. Install Drivers
Click the
Install Drivers
button to display the list of drivers software that can be installed with
your Motherboard. The Start Up program displays the drivers available for the particular
model of Motherboard you own. We recommend that you only install those drivers.
However, to display the list of all drivers software available with SOYO Motherboards, click
the
Display all drivers on the SOYO CD
button. Please make sure to install only the
drivers adapted to your system, or otherwise this cause system malfunctions.
6IEB
SY-6IEB
Quick Start Guide
13
Hardware
Installation
The following drivers are available for Windows 95
(Driver Installation Menu)
The following drivers are available for Windows 98
(Driver Installation Menu)
Please select the driver you want to install and click OK, You will have to
restart your system after installation. Only the drivers that are relevant
to your board are displayed initially.
Intel Southbridge Drivers
Intel Bus Master Drivers for Win95
SOYO CD Xpress utility
SOYO Speedpro BusMaster Driver for win 95/98
Intel Bus Master Drivers for Win NT
Intel Bus Master Drivers for OS/2
Cancel
Display all drivers
on the SOYO CD
OK
Driver Installation
Please select the driver you want to install and click OK, You will have to
restart your system after installation. Only the drivers that are relevant
to your board are displayed initially.
SOYO CD Xpress utility
SOYO Speedpro BusMaster Driver for win 95/98
Intel Bus Master Drivers for Win NT
Intel Bus Master Drivers for OS/2
Cancel
Display all drivers
on the SOYO CD
OK
Driver Installation
SY-6IEB
Quick Start Guide
14
Onboard Sound
Driver Installation
A short description of all available drivers follows:
Ø Intel Southbridge Drivers
Because Windows 95 does not recognize the Southbridge of the newer Intel chipsets (TX,
BX, ZX etc) this utility has to be run, it will update the necessary Windows files. (Only for
Windows 95)
Ø SOYO SpeedPro Busmaster Driver for Win 95/98
Without the busmaster drivers the CPU will need to be involved every time data is read from
or written to the Harddisk. The busmaster drivers make use of DMA (Direct Memory Access)
to relieve the CPU of this burden, thus speeding up the system.
The SOYO SpeedPro driver makes use of an advanced caching algorithm, which gives it an
advantage over other busmaster drivers.
Ø Intel Busmaster Drivers for Windows 95
Ø Intel Busmaster Drivers for Win NT
Ø Intel Busmaster Drivers for OS/2
These are the official busmaster drivers as supplied by Intel.
Note: Do NEVER install two types of busmaster drivers on your system, this will
lead to conflicts and system instability. Therefore, if you install the SOYO
SpeedPro Busmaster driver you can NOT install the Intel Busmaster drivers.
Before installing a new busmaster driver first UNINSTALL the old busmaster
driver.
Ø SOYO CD Xpress Utility
This utility will enhance your CD-ROM Drive data-thoughput by using space on the Harddisk
as cache. This way application programs can access data faster. This utility is suitable for
Windows 95/98.
Select which driver you want to install and click
OK,
or click
Cancel
to abort the driver
installation and return to the main menu.
Note:
Once you have selected a driver, the system will automatically exit the SOYO CD to
begin the driver installation program. When the installation is complete, most drivers require
to restart your system before they can become active.
However, to display the list of all drivers software available with SOYO Motherboards, click
the
Display all drivers on the SOYO CD
button. Please make sure to install only the
drivers adapted to your system, or otherwise this cause system malfunctions.
SY-6IEB
Quick Start Guide
15
Hardware
Installation
Step 4. Enter the SOYO CD
Click the
Enter SOYO CD
button to enter the SOYO HTML database. The Start Up
program will activate the default HTML browser installed on your system (for example,
Internet Explorer or Netscape) to visualize the contents of the SOYO CD.
The SOYO CD contains useful information about your Motherboard and other SOYO
products available in as many as eleven different languages. For your convenience, this
information is available in HTML format, similar to the format widely used on the Internet.
(SOYO CD HTML Database in English*)
(* The list of menu options may vary between languages)
Note:
If no HTML browser is installed on your system, the Start Up program will prompt you
on whether or not you would like to install the Internet Explorer* browser. Click YES to install
the HTML browser. After the installation is complete, please restart your system. Then re-run
the SOYO CD and you will be able to browse the SOYO HTML database.
(* Internet Explorer is a Microsoft Trademark)
Edition: March 1999
Version 2.0
SY-6IEB
SERIAL
International Headquarters
Soyo Computer Inc., (Taiwan)
Tel: 886-2-2290-3300
Fax: 886-2-2298-3322
Web Site: http://www.soyo.com.tw
E-mail: [email protected]
USA Branch Office
Soyo Tek Inc., (USA)
Tel: (408) 452-7696
Fax: (408) 573-7696
Web Site: http://www.soyousa.com
E-mail: [email protected]
SOYO Europe
Soyo Europe B.V., (Holland)
Tel: 31-79-3637500
Fax: 31-79-3637575
Web Site: http://www.soyo-europe.com
http://www.soyo.nl
E-mail: [email protected]
Germany Branch Office
SOYO Deutschland GmbH
Tel: 49-(0)441-209100
Fax: 49-(0)441-203422
Web Site: http://www.soyo.de
Email:sales@soyo.de
Korea Branch Office
SOYO TECHNOLOGY CO., LTD.
Tel: 82-2-3272-6481
Fax: 82-2-704-2619
Web Site: http://www.soyo.co.kr/
Email:[email protected]
Email:[email protected]
U.K. Branch Office
SOYO (U.K.) LTD.
Tel: 44-(0)181-569 4111
Fax: 44-(0)181-569 4134
Web Site: http://www.soyo.nl
Email:[email protected]
Japan Branch Office
SOYO COMPUTER
®è¦¡·|ªÀ
Tel: 81-3-33682188
Fax: 81-3-33682199
Web Site: http://www.soyo.co.jp
E-mail: [email protected]
Hong Kong Branch Office
Soyo Hong Kong Ltd. (H.K.)
Tel: 852-2710-9810
Fax: 852-2710-9078
Web Site: http://www.soyo.com.hk
E-mail: [email protected]
China
GING MEI JEI LTD.
Tel: 86-10-6251-0089/91/92
Fax: 86-10-6251-0311
Web Site: http://www.soyo.com.cn
Email:soyo@public.bta.net.cn
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
SOYO Motherboard SY-6IEB Manuale utente
- Tipo
- Manuale utente
- Questo manuale è adatto anche per
in altre lingue
- English: SOYO Motherboard SY-6IEB User manual