AJA ROI Series Istruzioni per l'uso

Version 1.5r1

Published November 25, 2019

Installation and Operation Guide

ROI

Region of Interest Converters

DVI, DP, HDMI, SDI to SDI Scalers

ROI Series Mini-Converter v1.5r1 2 www.aja.com

Notices

Trademarks

AJA® and Because it matters.® are registered trademarks of AJA Video Systems, Inc.

for use with most AJA products. AJA™ is a trademark of AJA Video Systems, Inc. for

use with recorder, router, software and camera products. Because it matters.™ is a

trademark of AJA Video Systems, Inc. for use with camera products.

CION®, Corvid Ultra®, lo®, Ki Pro®, KONA®, KUMO®, ROI® and T-Tap® are registered

trademarks of AJA Video Systems, Inc.

AJA Control Room™, KiStor™, Science of the Beautiful™, TruScale™, TruZoom™,

V2Analog™ and V2Digital™ are trademarks of AJA Video Systems, Inc.

All other trademarks are the property of their respective owners.

Copyright

this manual is subject to change without notice. No part of the document may be

reproduced or transmitted in any form, or by any means, electronic or mechanical,

including photocopying or recording, without the express written permission of AJA

Video Systems, Inc.

Contacting AJA Support

When calling for support, have all information at hand prior to calling. To contact AJA

for sales or support, use any of the following methods:

Telephone +1.530.271.3190

FAX +1.530.271.3140

Web

https://www.aja.com

Support Email

suppor[email protected]

Sales Email

[email protected]

ROI Series Mini-Converter v1.5r1 3 www.aja.com

Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Contacting AJA Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Chapter 1 – Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Video Processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Audio Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Control Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Pixel Clock Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

ROI Processing Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Mini-Cong Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Simplied Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

I/O Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

ROI-HDMI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

ROI-DP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

ROI-DVI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

ROI-SDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Models ROI-HDMI, ROI-DP, ROI-DVI . . . . . . . . . . . . . . . . . . . . . . . . . 11

Model ROI-SDI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Typical ROI Congurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Chapter 2 – Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

USB Control and Setup—Using AJA Mini-Cong . . . . . . . . . . . . . . . . . . 16

Acquiring Mini-Cong. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Installing Mini-Cong . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Running Mini-Cong. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Operating Mini-Cong . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Tabbed Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Input Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Click and Drag Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Screen Picker Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Output Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

About the Rotation, Flip, and Frame Delay Controls . . . . . . . . . . . . . . . 27

HDMI Screen (applicable only to ROI-SDI model) . . . . . . . . . . . . . . . . . . 29

Monitor Matrix Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Genlock Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

ROI-HDMI and ROI-DVI Genlock Screen. . . . . . . . . . . . . . . . . . . . . . . 31

ROI-SDI Genlock Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

ROI-DP Genlock Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Audio Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

ROI-HDMI and ROI-DVI Audio Screen . . . . . . . . . . . . . . . . . . . . . . . . 34

ROI-DP Audio Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

ROI-SDI Audio Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Update Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Info Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Appendix A – Specications . . . . . . . . . . . . . . . . . . . . . . . . 40

ROI-HDMI Tech Specs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

ROI-DP Tech Specs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

ROI-DVI Tech Specs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

ROI-SDI Tech Specs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Appendix B – Safety and Compliance . . . . . . . . . . . . . . . . . . 47

Contents

ROI Series Mini-Converter v1.5r1 4 www.aja.com

Warranty and Liability Information . . . . . . . . . . . . . . . . . . . .54

Limited Warranty on Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Limitation of Liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Governing Law and Language; Your Rights. . . . . . . . . . . . . . . . . . . . . . 54

Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

ROI Series Mini-Converter v1.5r1 5 www.aja.com

Chapter 1 – Introduction

Overview

AJA’s ROI family of scalers/scan converters allows exceptionally high quality

conversion of computer and video signals in a small Mini-Converter form factor.

The ROI models offer Region of Interest (ROI) support allowing DVI, HDMI, Display

Port, and SDI input signals to be scaled and converted to a SDI output. The ROI-

SDI model also provides a scaled HDMI output. With incredible image scaling,

extensive aspect ratio and frame rate conversion, ROI fulfills the need to scale

computer and video to a desired resolution, all in realtime, in a very portable and

easy to use package.

The four models of ROI Mini-Converters available are:

• ROI-DVI

• ROI-DP

• ROI-HDMI

• ROI-SDI

Video Processing

In default mode, the ROI-DVI, ROI-DP, and ROI-HDMI models automatically detect

the input signal format and convert it to the SDI (and HDMI, for the ROI-SDI)

output video format. Their respective DVI, DP and HDMI outputs pass the signal

through without any processing, maintaining the incoming signal aspect ratio.

For the ROI-SDI, the incoming signal is passed to the SDI Loop Through Output,

without any processing, maintaining the incoming signal aspect ratio. The

processed signal goes to both the HDMI output and the SDI output.

If the SDI output raster is larger than the input raster, unused area is filled with

matte color.

To realize the full power of ROI, however, you will need to use the supplied USB

cable and AJA’s Mini-Config application to select the desired output format and

perform a variety of region-of-interest and output display scaling operations.

Once configured, the ROI unit can run standalone.

Audio Handling

ROI-DVI, ROI-DP, ROI-HDMI

Analog audio from the host can be input via a standard 3.5mm audio cable and

mapped to the embedded SDI output stream. Alternatively, if the input is HDMI

or DP, its embedded audio can be the audio input. The ROI-DVI model can receive

both DVI and HDMI protocol input, and accepts audio if it is embedded in an

HDMI signal. However, the DVI protocol does not carry audio, so if the ROI-DVI is

receiving DVI input, only analog audio can be embedded to the output.

ROI-SDI

Digital audio embedded in the SDI input is carried through to both the SDI output

and the HDMI output. Analog audio can be output through the two analog RCA

Jacks (2 channels). Digital audio can be embedded through the SDI output as 24-

bit, 8 channel, and/or through the HDMI output as 24-bit, 2 channel or 8 channel.

ROI Series Mini-Converter v1.5r1 6 www.aja.com

Control Interface

For control, the ROI is connected to a computer via USB. The ROI has no local,

physical user-interface (no dipswitch settings). The ROI can operate stand-alone

without a USB connection to the host. In this mode, the ROI automatically adapts

to the input signal, and operates according to defaults or as last configured via

the AJA Mini-Config application (see "Chapter 2 – Operation" on page 16).

HDCP Protection

The ROI honors HDCP, and will not allow an HDCP link. If the input content is

HDCP protected, no source video will be displayed on the ROI’s DVI pass-through

connector, or on the ROI’s SDI output.

Features

ROI-HDMI

• Converts HDMI input to 3G, HD, or SD-SDI output

ROI-DP

• Converts DisplayPort input to 3G, HD, or SD-SDI output

ROI-DVI

• Converts DVI input to 3G, HD, or SD-SDI output

ROI-SDI

• Extracts 3G-SDI input and outputs to 3G, HD, SD-SDI and/or HDMI

All ROI Models

• High quality scaling and scan conversion

• User-adjustable “region of interest,” separate controls for input and output

• 4:3/16:9 conversion modes supported

• Setup via PC/Mac using Mini-Config software with the USB port and supplied

USB cable

• Frame-rate conversion

• Automatic configuration to input video raster and frame rate

• SDI output configurable to most common SD, HD and 3G formats (1080p 60

max)

• Edge filtering control

• Rotation, Horizontal and Vertical flip controls

• Monitor Matrix setup controls

• Frame delay control

• Genlock and frame sync with reference input

• Adjustable Horizontal and Vertical video delay from sync input

• Audio input via 3.5mm 2-channel analog input or 8-channel embedded (if

present) (excluding ROI-SDI model)

• Embedded SDI audio out (up to 8 channels)

• Uses universal input +5V power supply AJA model DWP-U-R1 (included)

• 5-year warranty

ROI Series Mini-Converter v1.5r1 7 www.aja.com

Pixel rates are limited to a 165MHz maximum rate.

Pixel Clock Rate

ROI-DVI, ROI-DP, ROI-HDMI

The source video pixel clock is a combination of the video resolution and its

vertical rate. Some sources can generate pixel clock rates that exceed the

capabilities of the ROI-DVI, ROI-DP, and ROI-HDMI converters. It may not be

obvious what the resulting pixel clock will be for a particular resolution or vertical

rate.

For example, when a downstream sink device is connected to the ROI output

monitor connector, the source and sink could potentially negotiate a display

format (using EDID) that is beyond the capability of ROI’s video processing

circuitry.

When this error occurs, an “Exceeds max rate” red error message will be displayed

on the Mini-Config user interface, and the ROI will generate a full screen red

matte on the SDI output. A downstream DVI/DP/HDMI/SDI monitor will still

display the incoming video.

Possible solutions include:

• Disconnect the downstream device (for example, a computer monitor) from

the ROI. Once disconnected, ROI will negotiate directly with the source to

generate a video resolution that is within the ROI’s processing capability.

• Reconfigure the source signal to a resolution that ROI supports.

• On ROI-DP models, from the Genlock Screen, select ROI-DP from the EDID

Flow Through control so that the upstream source sees only the EDID of the

ROI (see "EDID Flow Through" on page 33).

ROI Processing Capabilities

The ROI models utilize a powerful scaling processor, however, some specific

combinations of input and output ROI selections, de-interlacing, and 180°

rotations or flips can exceed the processing capacity of the ROI Mini-Converters.

In these cases, a “Processing Limit Exceeded” red error message is displayed on

the Mini-Config user interface, and the ROI will automatically turn off certain

features in order to process the picture. These features that have been turned

off will be reported and will be in red. For an example, see "Figure 19. Processing

Limit Exceeded" on page 28.

Possible solutions include:

• Reduce the size of the Region of Interest selections; input ROI, output ROI, or a

combination of both.

• Turn off 180 degree rotation and/or H and V flips, or frame delay.

• Use a progressive rather than interlace input signal.

Mini-Config Overview

Using AJA’s Mini-Config application, you can set up and control region-of-interest

and output display scaling operations, route audio, and configure genlock. Mini-

Config is also used to update the Mini-Converter firmware.

ROI Series Mini-Converter v1.5r1 8 www.aja.com

Simplified Block Diagram

Figure 1. ROI Converter/Scaler, Simplified Block Diagram

Reference

Input

Mini

Audio

Jack

USB

Port

Input

Pass-Thru Path

Free Run

Audio Delay

Audio ADC

USB Cong

Control

8 CH

SRC

Processed

SDI Output

HDMI/DVI/

DP/SDI

Video Input

ROI Model

Input and Output

C

onnectors:

Embedder

ROI-DVI

DVI-D

Connector

ROI-DP

DisplayP

ort

Connector

ROI-HDMI

HDMI

Connector

Unprocessed

Video Output

Sync Stripper

InterlacerFRC/Genlock

Deinterlacer KeyerROI Scaler

Matte Gen

ROI-SDI

3G-SDI

Connector

(excluding ROI-SDI)

Audio Output

Analog RCA

Jacks

(ROI-SDI only)

Processed

HDMI Output

(ROI-SDI only)

HDMI/DVI/

DP/SDI Output

I/O Connections

ROI-HDMI

Figure 2. ROI-HDMI Converter/Scaler

HDMI Input

Connector

Analog 2-Channel

Audio Input

+5-20 VDC

Power Input

HDMI

Output

Connector

SDI Output

BNC

Reference

Input BNC

USB Port

Power LED

HDMI Input

Connects to your computer or single-link source device.

ROI Series Mini-Converter v1.5r1 9 www.aja.com

To connect a DVI video input to the ROI HDMI input connector, use a passive DVI-

to-HDMI adapter (user-supplied). You can also use a cable adapter that has a DVI

connector on one end of the cable and an HDMI connector on the other.

HDMI Output

This is a pass-through output for use on a second computer monitor for using

the AJA Screen Picker feature (see "Screen Picker Operation" on page 23).

Connections are the same as described for DVI/HDMI input above.

ROI-DP

Figure 3. ROI-DP Converter/Scaler

DisplayPort

Input

Connector

Analog 2-Channel

Audio Input

USB Port

+5-20 VDC

Power Input

DisplayPort

Output

Connector

SDI Output

BNC

Reference

Input BNC

Power LED

DisplayPort Input

Connects to your Computer or single-link source device.

DisplayPort Output

This is a pass-through output for use on a second computer monitor for using

Screen Picker. Connections are the same as described for DisplayPort input above.

ROI Series Mini-Converter v1.5r1 10 www.aja.com

ROI-DVI

Figure 4. ROI-DVI Converter/Scaler

DVI Input

Connector

Analog 2-Channel

Audio Input

+5-20 VDC

Power Input

DVI

Output

Connector

SDI Output

BNC

Reference

Input BNC

USB Port

Power LED

DVI Input

Connects to your Computer or single-link source device.

To connect an HDMI video input to the ROI DVI input connector, use a passive

HDMI-to-DVI adapter (user-supplied). You can also use a cable adapter that has an

HDMI connector on one end of the cable and a DVI connector on the other.

DVI Output

This is a pass-through output for use on a second computer monitor for using

Screen Picker. Connections are the same as described for DVI/HDMI input above.

ROI Series Mini-Converter v1.5r1 11 www.aja.com

ROI-SDI

Figure 5. ROI-SDI Extracter/Scaler

3G-SDI Input

Connector

+5-20 VDC

Power Input

HDMI

Output

Connector

3G-SDI

Output BNC

Reference

Input BNC

USB Port

Power LED

3G-SDI Loop

Through

Connector

2 Audio

Output

Analog RCA

Jacks

3G-SDI Input

Connects to your 3G-SDI source signal or single-link source device.

3G-SDI Loop Through Output

This is a pass-through output for use on a second monitor.

NOTE: To adjust the region of interest selection, use the methods described in the

section for the "Input Screen" on page 21 with either the processed HDMI

output signal or the processed 3G-SDI output signal feeding a monitor.

Models ROI-HDMI, ROI-DP, ROI-DVI

Analog Audio

A single 3.5 mm analog audio connector accepts two channels of analog audio

which can be embedded into the SDI output as determined by the audio

configuration set using Mini-Config.

ROI Series Mini-Converter v1.5r1 12 www.aja.com

USB Port

Accepts USB mini connector

SDI Video Output

Standard BNC connector for coaxial SDI monitor connection.

Reference Video Input

The Reference BNC accepts an Output timing reference signal. The reference can

be SD Blackburst or HD tri-level sync.

Model ROI-SDI

Digital/Analog Audio

The 3G-SDI input connector accepts 8 channels of embedded digital audio, which

can be embedded into the SDI output, embedded into the HDMI output, and/or

output as 2 channels of analog audio as determined by the audio configuration

set using Mini-Config.

USB Port

Accepts USB mini connector

SDI Video Output

Standard BNC connector for coaxial SDI monitor connection.

Reference Video Input

The Reference BNC accepts an Output timing reference signal. The reference can

be SD Blackburst or HD tri-level sync.

Typical ROI Configurations

This section covers six example configurations of ROI, including ROI-DVI, ROI-

HDMI, and ROI-SDI.

Two typical configurations for using the ROI for scaling of desktop region-of-

interest computer-sourced video are illustrated in the following two figures.

In these configurations, the pass-through monitor is used to view the subject

desktop video and to use the Mini-Config application’s Screen Picker function to

select the desired region for output to SDI (see "Screen Picker Operation" on page

23).

ROI Series Mini-Converter v1.5r1 13 www.aja.com

Figure 6. ROI with Laptop Computer, System Interconnect Diagram

ROI

HDMI/DP/DVI HDMI/DP/DVI

USB

SDI Output

Source Computer

w/ Mini-Cong

Video

Monitor

Computer Desktop

Monitor

(ROI Pass-through)

Figure 7. ROI with Tower Computer & Two Monitors, System Interconnect

Diagram

ROI

USB

SDI Output

Source Computer

Tower

w/ Mini-Cong

Video

Monitor

Computer

2nd Desktop

Monitor

(ROI Pass-through)

Computer Desktop

Monitor

Monitor 2 Out

Monitor 1 Out

HDMI/DP/DVI HDMI/DP/DVI

HDMI/DP/DVI

A third example (Figure 8) illustrates use of the ROI Rotation feature to send

selected areas of a SDI signal to portrait mounted on-set monitors at full

resolution. Each monitor uses one ROI converter, accomplishing the task at a

much lower cost than dedicating DVE channels for rotation and resizing.

ROI Series Mini-Converter v1.5r1 14 www.aja.com

Figure 8. ROI Rotation with Portrait Mounted On-Set Monitors

ROI B

USB

HDMI Output

ROI A

Portrait

SDI Monitors

Built Into Set

Region

A

Region

B

SDI Loop-Through

- Input ROI Selection: 9x16 Fixed Aspect

- Output ROI Out Scaling: Full Screen Rotated 90 Degrees

SDI

Digital Video

Camera

Computer

w/ Mini-Cong

A fourth example below illustrates sending HDMI digital video from a camera to

a ROI to allow region of interest video input to a video switcher. Since the source

video is not coming from the computer that is running Mini-Config, the Screen

Picker feature cannot be used in this configuration (Figure 9).

Figure 9. ROI-HDMI with Video Camera to Switcher Interconnect Diagram

ROI

HDMI HDMI

USB

SDI

Output

Computer

w/ Mini-Cong

Video Switcher

Digital Video

Camera

Computer Desktop

Monitor

(ROI Pass-through)

In a parallel configuration as Figure 9, Figure 10 below shows a basic

configuration of the ROI-SDI being used to send a 3G-SDI digital video signal from

a 3G-SDI source to allow region of interest video input to a video switcher. As in

Figure 9, since the source video is not coming from the computer that is running

Mini-Config, the Screen Picker feature cannot be used in this configuration.

However, you can use the other methods for adjusting the region of interest

selection described in the section for the "Input Screen" on page 21 with either

the processed HDMI output signal or the processed 3G-SDI output signal feeding

a monitor.

ROI Series Mini-Converter v1.5r1 15 www.aja.com

Figure 10. ROI-SDI with 3G-SDI Source to Switcher Interconnect Diagram

ROI-SDI

HDMI

USB

SDI

Output

Computer

w/ Mini-Cong

Video Switcher

HDMI Monitor

3G-SDI Source

Installation

Typically, ROI installation consists of the following steps:

1. Ensure the ROI is disconnected from power.

2. Connect your computer or video console monitor output to the ROI’s HDMI/

DVI/DP input connector. For ROI-SDI, connect your SDI source signal to the

ROI’s SDI input connector.

3. Connect the ROI’s HDMI/DVI/DP output connector to a second monitor

(optional). For ROI-SDI, this would be the SDI Loop output connector.

4. Connect a video monitor to the converter SDI output BNC. The ROI-SDI

oers both an HDMI output and an SDI output for the processed signal.

5. If using ROI-HDMI/DVI/DP, connect two-channel analog audio input to

analog audio connector (optional).

6. If using ROI-SDI, connect two analog RCA jacks (optional).

7. Apply power to the converter (AJA power supply included).

8. The converter will now run using the default factory settings. If you wish to

alter the factory settings, you’ll need to:

• Install the AJA Mini-Config software onto your computer.

• Attach the converter via USB cable (included).

• Make your changes using Mini-Config setup screens.

ROI Series Mini-Converter v1.5r1 16 www.aja.com

Chapter 2 – Operation

IMPORTANT: Once the ROI has been congured with Mini-Cong, those settings will continue to be used in stand-alone

mode (disconnected from USB) as long as the input format remains the same. If a dierent input format is connected, the

ROI will revert to Auto mode. However, if the original input format is re-connected, the ROI will exit Auto mode and restore

the previously congured settings for that format.

USB Control and Setup—Using AJA Mini-Config

Your AJA Mini-Converter can be used right out of the box for some applications

since it is designed to recognize inputs and perform standard actions

automatically by default. However, to use its full capability, you must use AJA’s

Mini-Config software application for PCs and Macs. This same application can be

used to update to new Mini-Converter software released by AJA.

Acquiring Mini-Config

AJA’s Mini-Config application is available for download from the AJA website.

To download the latest Mini-Config package, which includes the Mini-Config

application, Mini-Converter firmware, and documentation, go to:

https://www.aja.com/en/products/mini-converters/mini-cong-software

Select either the Windows or Mac icon to download the desired version.

Mini-Converter Documentation

Included with the Mini-Config package is a complete set of documentation for

all Mini-Converters supported by Mini-Config. A .PDF of the Installation and

Operation Guide for the currently connected Mini-Converter can be accessed from

the Mini-Config UI via the Help/Manual drop-down menu.

Documentation for all AJA Mini-Converters that use Mini-Config can also be

accessed directly in the Mini-Config download package Documentation folder,

and via the Documentation icon available on the Mac installer.

Documentation (and firmware) included with the Mini-Config application are the

versions available at the time of distribution. However, Mini-Converter software,

firmware and documentation are updated regularly, so newer versions may exist.

To download the latest documentation for an individual Mini-Converter, go to:

https://www.aja.com/en/category/mini-converters

and navigate to the Support webpage of that Mini-Converter.

Installing Mini-Config

PC Installation

To install Mini-Config on a Windows PC:

1. Download the application from the AJA website (select the Windows icon

on the Mini-Config Support webpage).

2. Open the AJA_MiniCong.zip le

3. Double-click on the MiniInstaller.msi le.

ROI Series Mini-Converter v1.5r1 17 www.aja.com

4. A Setup Wizard will guide you through the installation.

Figure 11. Mini-Config PC Setup Wizard

5. Click Next to begin. Answer the questions in the subsequent dialogues.

When nished, an AJA Mini-Cong shortcut will be installed on the desktop,

and you will be able to locate the Mini-Cong application in the AJA folder

in the Programs listing.

NOTE: If the Mini-Config application already exists on the PC, a different Setup Wizard

appears.

Figure 12. Mini-Config Setup Wizard, Reinstallation

With this screen you can Repair (reinstall) or Remove (uninstall) Mini-Config on

the PC.

Mac Installation

To install the application on a Mac:

NOTE: Macintosh computers must be Intel-based (G5, G4 and earlier models will not

work with Mini-Config).

1. Download the application from the AJA website (select the Apple icon on

the Mini-Config Support webpage).

2. Open the AJA_MiniCong folder.

ROI Series Mini-Converter v1.5r1 18 www.aja.com

3. Double-click on the AJAMiniCong.dmg le.

4. Answer the prompt and a utility program will be launched.

Figure 13. Mini-Config Mac Installer

5. To complete the installation drag the “MiniCong.app” icon to the

Applications folder.

Running Mini-Config

Connect the Mini-Converter to the PC or Mac via the supplied USB cable. Connect

the external power supply (supplied) to the Mini-Converter.

PC Startup

To run Mini-Config on a PC, double-click on the AJA Mini-Config icon on your

desktop, or open the AJA folder in the program list and click on the AJA Mini-

Config application located inside the Mini-Config folder.

Mac Startup

To run Mini-Config on a Mac, open the Applications folder and locate the AJA

Mini-Config application. Double-click the application to launch it.

ROI Series Mini-Converter v1.5r1 19 www.aja.com

Saving Setups

A File drop down menu on the Mini-Config application bar allows you to save the

current state of the Mini-Converter to a preset file for later recall.

Using this feature you can set up the converter for different applications, storing

each configuration (Save Preset As...) with a unique name for easy recall (Open

Preset...).

A Revert to Factory Settings menu item similarly allows you to change the

settings back to AJA’s factory defaults.

Operating Mini-Config

The Mini-Config application provides a graphic interface for viewing settings

and updating software. It consists of an information area at the top that shows

the available Mini-Converters attached to the computer via USB, with a graphical

rendering of the selected Mini-Converter showing all the connectors and their

current state.

Colored text next to the connectors indicates the signal type and what the Mini-

Converter is doing:

• Blue text indicates the values automatically selected

• Black text indicates values that you have manually selected

• Red text indicates the Mini-Converter is not detecting a signal, or cannot

operate with the current user settings.

NOTE: Even if no output device is detected, the SDI connector text still shows the

signal it is outputting.

NOTE: Configuration settings in red will change based on the attached output device

as well as input signals. For improved accuracy and reliability, you should

configure the Mini-Converter only when the target output device is attached

and input signals are supplied at the inputs.

Screens are virtually the same on both PC and Mac, with subtle differences that

reflect the general look of the platform environment.

ROI Series Mini-Converter v1.5r1 20 www.aja.com

Figure 14. Example Mini-Config Screen

Select a USB port and an

attached Mini-Converter

(name in parentheses)

Each connector is

labeled with the signals

currently detected or

manually selected.

Firmware version

Serial Number

Tabbed screens

Firmware version

Selecting a Mini-Converter with the pulldown menu causes this application to

connect to the selected converter. The graphic of Mini-Converter and text below

it provides:

• Type of converter

• Firmware version

• Serial number of the unit.

A status field at the bottom of the screen shows if your application is connected

and communicating with the Mini-Converter.

When configuring the Mini-Converter, select it from the top pulldown, view the

current settings and change any values. Making a change communicates that

new value to the Mini-Converter’s non-volatile memory.

Tabbed Screens

The Tabs delineate control screens with groups of controls for each type of task to

be performed.

The controls for the actual configuration parameters are specific to each Mini-

Converter type. When you Click on any of the tab buttons, the pane below

the tabs will change to match your tab selection. Any changes you make are

immediately applied and will be saved, overwriting previous settings.

NOTE: In this manual Mini-Config screens for the ROI-HDMI model are shown. Other

ROI models have similar screens, with a few exceptions that are noted.

La pagina sta caricando ...

AJA ROI Series Istruzioni per l'uso

Questo manuale è adatto anche per

AJA ROI Series Istruzioni per l'uso

in altre lingue

Documenti correlati

Altri documenti