Datalogic Scanning DLL2020-WO Manuale utente

Marca: Datalogic Scanning

Modello: DLL2020-WO

Categoria: Lettori di codici a barre

Tipo: Manuale utente

Questo manuale è adatto anche per

Laptop DLL2020-WO

User's manual

Datalogic DLL2020-WO

or in part, be copied, photocopied, reproduced, translated or converted to any electronic medium or

machine readable form without prior written consent of Datalogic.

Limited Warranty

Under all circumstances this manual should be read attentively, before installing and/or using the pro-duct.

In no event Datalogic will be liable for any direct, indirect, special, consequential or incidental damages

arising out of the use or inability to use this documentation or product, even if advised of the possibility of

such damages. In particular, Datalogic shall not be liable for any hardware, software, or data that is stored

or used with the product, including the cost of repairing, replacing or recovering the above. Datalogic

reserves the right to change parts of the device at any time without preceding or direct announcement to

the client.

Datalogic reserves the right to revise this manual, and to make changes in the contents without obli-gation

to notify any person or entity of the revision or change. A serial number appears on the product. Make sure

that this official registration number has not been removed. It should be used whenever servicing by

Datalogic or an authorized Datalogic dealer is ne-cessary.

Important

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

EN55022, and with the limits for a class A digital device, pursuant to part 15 of the FCC rules. These limits

are designed to provide reasonable protection against harmful interference when the equipment is operated

in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the user’s manual, may cause harmful interference to radio

communications. Operation of the equipment in a residential area is likely to cause harmful interference in

which case the user will be required to correct the interference at his own expense. Any unauthorized

changes or modifications to this equipment could void the user’s authority to operate this equipment.

For CE-countries:

- The Dll2020-wo is in conformity with the CE standards.

For USA & Canada:

- To be used with UL listed and CSA certified computers/POS systems.

- À utiliser avec des ordinateurs/systèmes POS registrés UL/certifiés CSA.

Radio and television interference

Operation of this equipment in a residential area can cause interference to radio or television reception. This

can be determined by turning the equipment off and on. The user is encouraged to try to correct the

interference by one or more of the following measures:

• Re-orientate the receiving antenna

• Relocate the device with respect to the receiver

• Move the device away from the receiver

• Plug the device into a different outlet in order to have the device and receiver on different branch

circuits

If necessary, the user should consult the manufacturer, an authorized Datalogic dealer or experienced

radio/television technician for additional suggestions. The booklet

"How to Identify and Resolve Radio-TV

Interference Problems"

, prepared by the Federal Communications Commission, can be of help. It can be

obtained from the U.S. Government Printing Office, Washington, DC 20402, Stock No. 004000003454.

P/N A232001 September

’

Table of contents

Preface i

Chapter 1 The DLL2020-WO 1

1.1 Unpacking the DLL2020-WO 2

1.2 Scanning bar codes with the DLL2020-WO 4

1.3 Scanner labelling 7

1.4 Maintaining the scanner 11

1.5 Controlling the scanner from the POS system 11

Chapter 2 Installing the DLL2020-WO 13

Installing the scanner 14

Appendices A. Connector types and pin definitions 22

B. Technical specifications 23

C. Troubleshooting 24

Preface

The Datalogic DLL2020-WO is a high performance omni-directional scanner, which

provides optimal scanning conditions. The DLL2020-WO shares the same quality of

the GOLDRUSH

polygon and Scantium decoder chip as Datalogic’s popular Hunter

H-3010, Pollux P-4010 and Castor C-5010 scanners. Together with its compact and

ergonomic design, operator fatique and other discomforts are less then any

competitive omni-directional scanner.

These characteristics make the DLL2020-WO especially suitable for installation in

small counters such as in drugstores, pharmacies, department stores, tobacconists,

kiosks, petrol stations, and convenience stores.

The omni-directional scan field of the DLL2020-WO generates a scan pattern of

16 lines, ensuring high performance scanning. Featuring an unequalled scan rate of

800 scans per second, the DLL2020-WO is an aggressive scanner.

Barcodes are read simply on presentation to the scanner window. However, the

ergonomic design of DLL2020-WO rubber sleeve, which fits naturally in the hand,

makes the unit easy to pick up when larger or heavier products have to be scanned.

The scanner con be installed ‘free-standing’ on a counter surface using its protective

rubber sleeve or without the sleeve, flush or surface fixed to check-out furniture,

making for a very neat installation.

The DLL2020-WO can also be supplied in different colours to match with corporate/-

retail designs and schemes thus enhancing the check-out environment even further.

This manual contains two chapters and three appendices. The first chapter describes

the DLL2020-WO scanner, its general features as well as the way in which it can be

used. The precise instructions for installing the scanner are listed in the second

chapter. Default settings can be changed using the bar code labels in the

Configuration Guide supplied with the scanner. Appendix A shows the connector types

of the scanner. Technical specifications of the DLL2020-WO can be found in Appendix

B. Refer to Appendix C for troubleshooting if the scanner is not working properly.

Chapter 1

The DLL2020-WO

1.1 Unpacking the DLL2020-WO

Take the scanner and its accessories out of the box and remove all

packing materials. Refer to the packing list in order to ensure that you

have received all the items ordered. Visually inspect the scanner and

accessories for any visible traces of damage. Refer to the figure in

paragraph 1.3 to locate the interface label and verify if the scanner

interface corresponds with the host system interface. Immediately contact

your supplier if anything appears to be damaged, or if the supported

interface does not correspond with the host system interface.

Red LedGreen Led Good read buzzer

Detachable

handle

Sleep mode switch

Rubber sleeve

2 The DLL2020-WO

The various parts of the DLL2020-WO are:

Sleep mode switch If a sleep mode time-out has been programmed,

the scanner can be reactivated by pressing this

switch. The sleep-mode feature can be program-

med by means of the menu labels in the

Configuration Guide.

NOTE: The default value for the sleep mode

time-out is set to 30 minutes. When the

scanner is in sleep mode, the LED is

intermittently flashing red.

Red LED The red LED indicates that the scanner is ready to

read a bar code.

Green LED The green LED indicates a good read.

Good read buzzer The buzzer sounds whenever data have been

correctly read. The frequency can be adjusted by

means of the menu labels from the Configuration

Guide.

Rubber sleeve A rubber sleeve encloses the scanner. The sleeve

protects the scanner, and takes care that it does

not slide when installed ‘free-standing’ on a counter

surface. Furthermore, its ergonomic design makes

the unit easy to pick up; it fits naturally in the hand.

Detachable handle A handle can be attached to the scanner,

depending on the preference of the user. The

handle makes the scanner easy to pick up, in case

large or heavy products need to be scanned.

The DLL2020-WO 3

1.2 Scanning bar codes with the DLL2020-WO

The DLL2020-WO is an omnidirectional scanner featuring a 4-directional

scan field with a 16-lines scan pattern. Bar codes can easily be read by

presenting them to the scanner. The scan volume is illustrated in the

figure above. The optimal reading zone lies between 3 and 15 cm from

the scanner window. However, bar codes can still be read up to 25 cm

(10 inch) from the scanner window.

25 cm

15 cm

3 cm

4 The DLL2020-WO

The Dll2020-wo scanner can be used handsfree as well as hand held,

e.g.:

a) Handsfree scanning by presenting the item to the scanner.

b) Bar code labels can also be scanned in hand held mode, by taking the

scanner by the handle and hold it in front of the bar code label on the

product.

The DLL2020-WO 5

c) You can also hold the scanner without the handle.

6 The DLL2020-WO

1.3 Scanner labelling

There are four labels on the scanner. The first three labels can be found

on the housing of the DLL2020-WO, as indicated in the figures below. The

fourth label is visible through the scanner window.

All the labels have been attached by the manufacturer and should in no

case be removed.

The scanner’s serial number can be found under the bar code label. This

official registration number is strictly related to the device. The supplier

may ask for this number when the scanner needs servicing.

The DLL2020-WO 7

Laser safety

English:

The DLL2020-WO scanner complies with safety standard IEC 825-1

(1993) for a Class 1 laser product. It also complies with U.S. 21CFR1040

as applicable to a Class IIa laser product. Avoid long term viewing of

direct laser light.

German:

Der Strichcode-Scanner DLL2020-WO entspricht den

Sicherheitsvorschriften nach IEC 825-1 (1993) für ein Laserprodukt der

Klasse 1. Er entspricht auch U.S. 21CFR1040, anwendbar auf ein

Laserprodukt der Klasse IIa. Vermeiden Sie langzeitiges Hineinblicken in

direktes Laserlicht.

Dutch:

De DLL2020-WO scanner voldoet aan de veiligheidsnormen IEC 825-1

(1993) voor een Klasse 1 laserprodukt. Tevens voldoet de scanner aan

U.S. 21CFR1040, van toepassing op een Klasse IIa laserprodukt. Vermijd

langdurig kijken in direkt laserlicht.

French:

Le scanner DLL2020-WO est conforme aux normes de sécurité IEC 825-1

(1993) s’appliquant à un produit laser de la classe 1. Il est également

conforme à la U.S. 21CFR1040 telle qu’elle s’applique à un produit laser

de la classe IIa. Eviter de rester exposé longtemps à la lumière directe du

laser.

Danish:

DLL2020-WO skanneren er i overensstemmelse med

sikkerhedsstandarden IEC 825-1 (1993) for laserprodukter i klasse 1. Den

er også i overensstemmelse med U.S. 21CFR1040, der gælder for

laserprodukter i klasse IIa. Undgå at se direkte på laserlys i længere

perioder.

8 The DLL2020-WO

Finnish:

DLL2020-WO-skanneri täyttää luokan 1 lasertuotteelle IEC 825-1:ssä

(1993) asetetut turvavaatimukset. Se täyttää myös U.S. 21CFR1040:ssa

asetetut vaatimukset siltä osin kuin ne koskevat luokan IIa lasertuotetta.

Vältä pitkäaikaista suoraan laservaloon katsomista.

Swedish:

Avsökaren DLL2020-WO uppfyller säkerhetsnormen IEC 825-1 (1993)

för laserprodukter av klass 1. Den uppfyller dessutom U.S. 21CFR1040

som gäller för laserprodukter av klass IIa. Undvik att titta i direkt laserljus

under längre perioder.

Norwegian:

DLL2020-WO skanneren er i samsvar med sikkerhetsstandarden IEC 825-

1 (1993) for laserprodukter i klasse 1. Den er også i samvar med U.S.

21CFR1040 for laserprodukter i klasse IIa. Unngå å se langvarig på

direkte laserlys.

Italian:

Lo scanner DLL2020-WO è conforme alle norme di sicurezza IEC 825-1

(1993) relative ad un prodotto laser di Classe 1. È inoltre conforme alla

norma U.S. 21CFR1040 relativa ad un prodotto laser di Classe IIa. Evitare

l’esposizione prolungata all’emissione diretta di luce laser.

Portuguese:

O scanner DLL2020-WO está conforme as normas de segurança IEC 825-

1 (1993) para a Classe 1 dos produtos laser. Também está conforme a

norma U.S. 21CFR1040 aplicada nos produtos laser da Classe IIa. Evite

expor os olhos directa e prolongadamente aos raios laser.

Spanish:

El scanner DLL2020-WO reune las normas de seguridad IEC 825-1 (1993)

para un producto laser de Clase 1. Y también reune las normas U.S.

21CFR1040 que se aplican a un producto laser de Clase IIa. Se debe

evitar mirar muy fijo en luz lasérica directa.

The DLL2020-WO 9

Optical The use of optical instruments with this product will

increase eye hazard. Optical instruments include

binoculars, microscopes and magnifying glasses

but do not include eye glasses worn by the user.

Radiant Energy The DLL2020-WO uses a low-power laser diode

operating at 650 nm in an opto-mechanical scanner

resulting in less than 0.7 mW peak output power.

Laser light observed at 15.0 cm (5.9 inch) above

the window through a 7 mm (0.28 in.) aperture and

averaged over 1000 seconds is less than 3.9 µW

per CDRH Class IIa specification. Do not attempt to

remove the protective housing of the scanner, as

unscanned laser light with a peak output up to 0.90

mW could be accessible inside.

Laser Light Viewer The scanner window is the only aperture through

which laser light may be observed on this product.

A failure of the scanner motor, while the laser diode

continues to emit a laser beam, may cause

emission levels to exceed those for safe operation.

The scanner has safeguards to prevent this

occurrence. If, however, a stationary laser beam is

emitted, the failing scanner should be disconnected

from its power source immediately.

Adjustments Do not attempt to make any adjustments to or

alteration of this product. Do not remove the

scanner’s protective housing. There are no user-

serviceable parts inside.

CAUTION Use of controls or adjustments or performan-

ce of procedures other than those specified

herein may result in hazardous laser light

exposure.

10 The DLL2020-WO

1.4 Maintaining the scanner

The DLL2020-WO scanner requires little maintenance. Only occasional

cleaning of the scanner window is necessary in order to remove dirt and

fingerprints. The scanner can be cleaned during operation. To this end use

a non-abrasive glass spray cleaner and a soft lint-free cloth only.

1.5 Controlling the scanner from the pos system

The DLL2020-WO can be controlled from the POS system via the RS232C

interface. Controlling is accomplished by transmitting the following single-

byte commands to the scanner. In the Datalogic default setting the

following commands are available (more details upon request):

When the scanner is disabled, the scanner motor will remain switched-on

until the scanner goes into sleep mode.

ASCII code

0E Hex

0F Hex

05 Hex

function

enable (cancels disable)

disable

power-up re-initialization

byte is also called:

Shift Out or <Ctrl-N>

Shift In or <Ctrl-O>

ENQ or <Ctrl-E>

12 Hex

sleep

DC2 or <Ctrl-R>

14 Hex

wake (cancels sleep)

DC4 or <Ctrl-T>

The DLL2020-WO 11

POS system

Polaris P-7010

Scanner control

12 The DLL2020-WO

DLL2020-WO

Chapter 2

Installing the DLL2020-WO

14 Installing the DLL2020-WO

2.1 Installing the scanner

This chapter describes the instructions necessary for installing the

DLL2020-WO scanner.

Due to many POS systems on the market, a large number of

communication cables is available. Make sure that you have the right

cable to connect the scanner to your POS or computer.

Follow these steps carefully in order to install the scanner.

1. Locate the optimal scanner position in relation to the counter surface.

Pay attention to the product flow, the distance to the counter edge and

convenience for the operator.

■ The scanner and the host system must be switched off before

starting the installation of the scanner. By following this precaution

you prevent any electrical damage.

■ You are advised to install the scanner in an air circulated place out

of direct sunlight.

NOTES

Installing the DLL2020-WO 15

2. You have four options to connect the scanner to your POS or

computer.

A) RS232 direct power

For those systems which supply electrical power on the serial port

(minimal requirements: +5 V dc, 250 mA), the following set-up is

applicable.

Plug the cable with the 10-pin modular jack into the scanner port

until a firm ‘click’ is heard.

Plug the other connector of the cable into the appropriate serial

port of your POS or computer.

RS 232 direct power

Polaris

To host

Cable

Host

DLL2020-WO

16 Installing the DLL2020-WO

B) Keyboard Wedge direct power

For those systems which supply electrical power on the keyboard

port (minimal requirements: +5 V dc, 250 mA), the following set-up

is applicable.

Plug the cable with the 10-pin modular jack into the scanner port

until a firm ‘click’ is heard.

Connect the female connector at the other cable end to the

keyboard.

Plug the male connector into the keyboard port of your computer.

Keyboard Wedge direct power

Polaris

Cable

computer

To computer

To keyboard

DLL2020-WO

La pagina sta caricando ...

Datalogic Scanning DLL2020-WO Manuale utente

Marca: Datalogic Scanning

Modello: DLL2020-WO

Categoria: Lettori di codici a barre

Tipo: Manuale utente

Questo manuale è adatto anche per

Laptop DLL2020-WO

Scarica il pdf

rapporto

in altre lingue

English: Datalogic Scanning DLL2020-WO User manual
français: Datalogic Scanning DLL2020-WO Manuel utilisateur

Datalogic Scanning DLL2020-WO Manuale utente

Questo manuale è adatto anche per

Datalogic Scanning DLL2020-WO Manuale utente

in altre lingue

Altri documenti