3Doodler 8CPSBKUS3E Manuale utente

Tipo
Manuale utente
Getting the most out of your
Holen Sie das Meiste heraus aus Ihrem
Tirez le meilleur de votre
Aprovecha al máximo tu
Come utilizzare al meglio la
Haal het meeste uit je
Hello Bienvenue Bienvenido
Willkommen Benvenuti Hallo
Please do not throw these instructions away.
(We worked really hard to make sure they were as useful and
readable as possible!)
Merci de ne pas jeter ces instructions.
(Nous avons fait en sorte qu’elles soient aussi utiles et
compréhensibles que possible!)
No tires estas instrucciones.
(Nos hemos esforzado para que sean lo más útiles y amenas
posible).
Bitte werfen Sie diese Anleitung nicht weg.
(Wir haben uns wirklich sehr angestrengt, um sie so nützlich
und lesbar wie möglich zu machen!)
Conservare queste istruzioni.
(La realizzazione di questo manuale ha richiesto un intenso
lavoro al ne di orire la massima utilità e comprensione).
Gooi deze instructies niet weg aub. (We hebben hard gewerkt
om deze zo gebruiksvriendelijk en leesbaar mogelijk te
maken.
EN
FR
ES
DE
IT
NL
P.1
P.13
P.26
P.39
P.52
P.66
Revised: May 11, 2018
SLOW
FAST
the3Doodler.com
#WhatWillYouCreate?
Manufactured by / Fabriqué par / Fabricado por / Hergestellt von /
Fabbricato da / Gemaakt door WobbleWorks (HK) Limited.
Distributed by / Distribué par / Distribuido por / Vertrieben von /
Distribuito da / Gedistribueerd door WobbleWorks,Inc. /
WobbleWorks (HK) Limited, 89 5th Avenue, Suite 802, NY, NY, 10003.
© WobbleWorks, Inc. 2018
3Doodler_Bob_User_Manual_MAIN_Cover_&Back_20180511.indd 2 14/5/2018 9:45 AM
1
SECTION 1: WARNINGS
Disposal of this product
At the end of your 3Doodler Create+’s life, please do
not dispose of it in your general household waste. In
order to prevent possible harm to the environment
or human health from uncontrolled waste disposal,
please dispose of your 3Doodler Create+ separately
in accordance with local laws and regulations. For
more information on the separate collection systems
for waste electrical and electronic equipment, please
contact your local municipal authority. You can also
contact the retailer from which you purchased your
3Doodler Create+, who may have a recycling service, or
be part of a specic recycling scheme that you can use.
- The Nozzle of the 3Doodler Create+
can become hot. DO NOT touch the
Nozzle, or you may be burned!
- DO NOT allow the Nozzle near or in
contact with ammable materials.
- Inform others in the area that
the Pen is hot and should not be
touched.
Unplug and set the Control Switch
to OFF when not in use or before
storing.
Allow the Nozzle to cool completely
before storing.
The Unblocking Tool can become
hot. DO NOT touch the metal part
of the Unblocking Tool after using
it to clean your 3Doodler Create+,
or you may burn yourself!
DO NOT use the 3Doodler Create+
near bathtubs, showers, basins
or other vessels containing water.
This could result in death due to
electric shock.
The 3Doodler Create+ should only be
used with ABS or PLA, FLEXY plastic
lament approved by us. Misuse
of your 3Doodler Create+, setting
your pen to the wrong heating
temperature, and/or use of non-
approved plastics or other materials
may result in damage to your pen
or injury to you, and will void your
warranty. Injuries to the user may
include, but are not limited to, harm
sustained from inhaling substances
that are not suitable for heating; or
burns from ammable materials
used in the 3Doodler Create+.
ADULT USE ONLY.
KEEP OUT OF REACH OF CHILDREN.
WARNINGS
SECTION 2: GETTING STARTED
WITH 3DOODLER CREATE+
How it Works:
The 3Doodler Create+ melts Plastic and uses a motor and gears
(
Drive Gear) to push it through the Pen’s hot end (Nozzle) in a
thin line. This process is called extruding or extrusion, and we
will refer to it throughout this User Manual. Once extruded, Plastic
cools and hardens instantly, allowing you to draw on surfaces and
in the air. This User Manual will show you how!
We created this User Manual as a step-by-step guide to
get you comfortable with your 3Doodler Create+ and
its features. Once you are familiar with these steps, you
will be able to Doodle with condence. Skipping steps
may result in a less enjoyable time with your
3Doodler Create+.
LIGHT LEGEND:
Solid RED:
Heating up
(Please wait)
BLUE: ABS/FLEXY
GREEN: PLA
Flashing Light:
Reversing Plastic
Click once to start
Click once to stop
Double click to reverse
SPEED BUTTON
LEGEND:
1
2
3
4
5
6
3Doodler_Bob_User_Manual_MAIN_Inner_20180511.indd 1 11/5/2018 11:37 AM
2
Disposal of this product
At the end of your 3Doodler Create+’s life, please do
not dispose of it in your general household waste. In
order to prevent possible harm to the environment
or human health from uncontrolled waste disposal,
please dispose of your 3Doodler Create+ separately
in accordance with local laws and regulations. For
more information on the separate collection systems
for waste electrical and electronic equipment, please
contact your local municipal authority. You can also
contact the retailer from which you purchased your
3Doodler Create+, who may have a recycling service, or
be part of a specic recycling scheme that you can use.
ADULT USE ONLY.
KEEP OUT OF REACH OF CHILDREN.
SECTION 2: GETTING STARTED
WITH 3DOODLER CREATE+
How it Works:
The 3Doodler Create+ melts Plastic and uses a motor and gears
(Drive Gear) to push it through the Pen’s hot end (Nozzle) in a
thin line. This process is called extruding or extrusion, and we
will refer to it throughout this User Manual. Once extruded, Plastic
cools and hardens instantly, allowing you to draw on surfaces and
in the air. This User Manual will show you how!
We created this User Manual as a step-by-step guide to
get you comfortable with your 3Doodler Create+ and
its features. Once you are familiar with these steps, you
will be able to Doodle with condence. Skipping steps
may result in a less enjoyable time with your
3Doodler Create+.
LIGHT LEGEND:
Solid RED:
Heating up
(Please wait)
BLUE: ABS/FLEXY
GREEN: PLA
Flashing Light:
Reversing Plastic
Click once to start
Click once to stop
Double click to reverse
SLOW
FAST
Plastic
Plastic Loading Port
Hole for inserting Plastic
in the back of the
3Doodler Create+
Temperature Adjuster
(See the3doodler.com/
temperature)
Control Switch
For turning the 3Doodler
Create+ ON and OFF, and
selecting ABS / FLX or PLA
extrusion temperature
Control Port
Drive Gear
This pushes the Plastic
through the Pen
Nozzle
Hot end where Plastic is
extruded for Doodling
FAST Speed Button
SLOW Speed Button
Light
Tells you when your
3Doodler Create+ is ready
for Doodling
Power Adapter
Maintenance Cover
Allows you to look inside your
Pen to see what’s going on
SPEED BUTTON
LEGEND:
1
2
3
4
6
107
8
11
12
9
1 7
2 8
3 9
4 10
5 11
6 12
5
3Doodler_Bob_User_Manual_MAIN_Inner_20180511.indd 2 11/5/2018 11:37 AM
3
Slide Control Switch to
ABS / FLX.
Light will glow RED while the Pen is reaching the temperature
required to melt your Plastic. Once Light has turned BLUE,
your Pen is ready to extrude Plastic.
Step 1: Turn on your 3Doodler
Create+ and wait for it to heat up
Plug in the yellow hole of
3Doodler Create+.
Power Adapter
Light to BLUE
60-90
secs
Step 2: Load and extrude Plastic
Making sure the Light is still
BLUE, push the Plastic through
the Plastic Loading Port.
BLUE Light
Select one strand of ABS
(MATTE) Plastic (provided in
your 3Doodler Create+ box).
Click FAST button once and
release. You will hear the
Drive Gear start.
After 10-15 seconds, Plastic
will begin extruding from the
Nozzle. Extruded Plastic will
harden after a few seconds.
Press the FAST button once to
stop extruding.
x1
1
x1
3
4
3
2
2
5
Step 3: Doodle your name
Use box below to create your rst Doodle -
your name!
Write your name in the box
provided using marker, pen,
pencil, or any other writing
utensil of your choice. We
suggest cursive, or block with
the letters connected.
Doodle your name in a
continuous unbroken Doodle
by dragging the Plastic along
the paper as if you were
writing with a pencil, with all
letters connected. Keep your
movement slow and steady.
Bend the paper outwards to
pop your Doodled name o.
Your Name:
#MyFirstDoodle
1
3Doodler_Bob_User_Manual_MAIN_Inner_20180511.indd 3 11/5/2018 11:37 AM
4
Slide Control Switch to
ABS / FLX.
Light will glow RED while the Pen is reaching the temperature
required to melt your Plastic. Once Light has turned BLUE,
your Pen is ready to extrude Plastic.
Step 1: Turn on your 3Doodler
Create+ and wait for it to heat up
Step 2: Load and extrude Plastic
Making sure the Light is still
BLUE, push the Plastic through
the Plastic Loading Port.
BLUE Light
After 10-15 seconds, Plastic
will begin extruding from the
Nozzle. Extruded Plastic will
harden after a few seconds.
x1
Step 3: Doodle your name
Use box below to create your rst Doodle -
your name!
Write your name in the box
provided using marker, pen,
pencil, or any other writing
utensil of your choice. We
suggest cursive, or block with
the letters connected.
Doodle your name in a
continuous unbroken Doodle
by dragging the Plastic along
the paper as if you were
writing with a pencil, with all
letters connected. Keep your
movement slow and steady.
Bend the paper outwards to
pop your Doodled name o.
Click FAST button once. When
Plastic starts extruding, push
Nozzle down into paper to get
Plastic to stick to surface.
When you reach the end of your
name, stop extruding by clicking
the FAST button once again.
Your Name:
#MyFirstDoodle
1
3
5
2
4
3Doodler_Bob_User_Manual_MAIN_Inner_20180511.indd 4 11/5/2018 11:37 AM
5
x1
Step 4: Doodle in the air!
Please read all steps below before you begin
this section, which will teach you how to Doodle
vertically in the air.
Extrude Plastic onto a piece
of paper until you have a blob
about the size of a ladybug.
Make sure it is anchored into
the paper.
Click the FAST button to stop
extruding, BUT DO NOT MOVE
PEN YET.
Lift Pen and Plastic up o the
paper in a straight line for 1.5 in.
1.5-in
Wait a few seconds with the Pen
still connected to the top of your
Plastic line.
5-6
secs
Pull the Pen away. The line will
remain vertical.
Well done! You just Doodled in the air! This is
a crucial stepping stone to making all kinds of
wonderful three dimensional objects with your
3Doodler Create+.
Step 5: Doodle Even More!
For further guides, projects and inspiration,
please refer to:
YouTube videos: Cube
https://www.youtube.com/3Doodler
YouTube videos: Squiggly
https://www.youtube.com/3Doodler
Stencils provided at the back of this manual:
Glasses - P.82-83
Stencils provided at the back of this manual:
Eiel tower - P.79-81
Community projects for further inspiration
and guidance:
http://the3Doodler.com/community
MORE
Step 6: Reverse and Remove
Plastic
Once Plastic stops reversing,
it is safe to remove it from the
Pen by gently pulling on the
back of the strand.
With Pen set to ABS / FLX, wait
for BLUE Light to come on.
Plastic that is shorter than 5.3 inches cannot be reversed.
You should feed it all the way through your 3Doodler Create+ and
use it up. (Alternatively, you can push Plastic out the back - see
Section 3, Step 3B.)
NOTE:
Before we continue, it’s time you learned about the dierent
types of Plastic you can use with the 3Doodler Create+
(and which settings to use for each type).
ABS (MATTE):
Temp: ABS / FLX Temp
Light: BLUE
Feature: Great for drawing in the air.
How to tell: Plastic has white
semi-circle ends.
PLA (GLOSSY / CLEAR /
METALLIC / SPARKLE ):
Temp: PLA Temp
Light: GREEN
Feature: Gossy and making it perfect
for artistic creations.
How to tell: Very rigid, no white
semi-circle ends.
Now that you’ve Doodled with ABS Plastic, we want
to show you everything you need to know about
changing Plastic and introduce you to the dierent
types of Plastic.
FLEXY:
Temp: ABS / FLX Temp
Light: BLUE
Feature: Make exible,
bendable Doodles.
How to tell: Plastic is very exible.
After removing a Plastic strand
from the 3Doodler Create+,
cut and remove any partially
melted material at the end of
your strand before re-feeding
it into the 3Doodler Create+.
This will reduce blockages and
clogging issues.
TIP
TIP
1
3
5
2
4
3Doodler_Bob_User_Manual_MAIN_Inner_20180511.indd 5 11/5/2018 11:37 AM
6
Step 4: Doodle in the air!
Please read all steps below before you begin
this section, which will teach you how to Doodle
vertically in the air.
Lift Pen and Plastic up o the
paper in a straight line for 1.5 in.
Wait a few seconds with the Pen
still connected to the top of your
Plastic line.
Well done! You just Doodled in the air! This is
a crucial stepping stone to making all kinds of
wonderful three dimensional objects with your
3Doodler Create+.
Step 5: Doodle Even More!
For further guides, projects and inspiration,
please refer to:
YouTube videos: Cube
https://www.youtube.com/3Doodler
YouTube videos: Squiggly
https://www.youtube.com/3Doodler
Stencils provided at the back of this manual:
Glasses - P.82-83
Stencils provided at the back of this manual:
Eiel tower - P.79-81
Community projects for further inspiration
and guidance:
http://the3Doodler.com/community
Step 6: Reverse and Remove
Plastic
Once Plastic stops reversing,
it is safe to remove it from the
Pen by gently pulling on the
back of the strand.
With Pen set to ABS / FLX, wait
for BLUE Light to come on.
Double click either Speed
Button. Light will start ashing
to signal Plastic reversing.
x2
Flashing
BLUE
5.3
inches
Plastic that is shorter than 5.3 inches cannot be reversed.
You should feed it all the way through your 3Doodler Create+ and
use it up. (Alternatively, you can push Plastic out the back - see
Section 3, Step 3B.)
NOTE:
Before we continue, it’s time you learned about the dierent
types of Plastic you can use with the 3Doodler Create+
(and which settings to use for each type).
ABS (MATTE):
Temp: ABS / FLX Temp
Light: BLUE
Feature: Great for drawing in the air.
How to tell: Plastic has white
semi-circle ends.
PLA (GLOSSY / CLEAR /
METALLIC / SPARKLE ):
Temp: PLA Temp
Light: GREEN
Feature: Gossy and making it perfect
for artistic creations.
How to tell: Very rigid, no white
semi-circle ends.
Now that you’ve Doodled with ABS Plastic, we want
to show you everything you need to know about
changing Plastic and introduce you to the dierent
types of Plastic.
FLEXY:
Temp: ABS / FLX Temp
Light: BLUE
Feature: Make exible,
bendable Doodles.
How to tell: Plastic is very exible.
After removing a Plastic strand
from the 3Doodler Create+,
cut and remove any partially
melted material at the end of
your strand before re-feeding
it into the 3Doodler Create+.
This will reduce blockages and
clogging issues.
SNIP THOSE ENDS!
TIP
PLASTIC TYPES AND SETTINGS.
TIP
3
2
BLUE Light
1
3Doodler_Bob_User_Manual_MAIN_Inner_20180511.indd 6 11/5/2018 11:37 AM
7
x1
x1
Step 7: Let’s Switch to PLA Plastic!
With Pen on ABS / FLX, load a
new strand of PLA Plastic into
Plastic Loading Port. Use a
dierent color to the ABS you
were using before.
PLA Plastic
ABS Plastic
The color of the Plastic will
change once the PLA starts
extruding. It will appear mixed
at rst. STOP extrusion by
pushing either button once.
SLOW
FAST
Light to RED
Light to GREEN
Click FAST or SLOW once to
continue extruding the PLA
Plastic and Doodle as you wish.
Switch Pen to PLA setting. Wait
for Light to turn GREEN.
Step 8: Power Down
Remove all Plastic from the
Pen using the Reverse feature
(double click any Speed
Button). Friendly reminder to
snip those ends!
Move the Control Switch
to OFF.
Allow your 3Doodler Create+
to cool completely
before storing.
We recommend powering down and giving your 3Doodler
Create+ a 30 minutes break after every 2 hours of
continuous use.
After 5 minutes of inactivity, the 3Doodler Create+’s heating
system will automatically power down. You will need to press one
of the Speed Buttons OR toggle the Control Switch OFF and then
ON again to continue use.
NOTE:
SECTION 3: TROUBLESHOOTING
Tools (Provided in Box)
Before showing you how to troubleshoot issues
with your 3Doodler Create+, we want to introduce
you to three handy tools provided in your box:
Mini Screwdriver
Keep this handy
for removing the
Maintenance Cover.
Keep this handy
for removing the
Maintenance Cover
or rotating the
Temperature Adjuster
(See the3doodler.com/
temperature)
With those introductions over, it’s time to look
at the dierent issues that may arise with your
3Doodler Create+ and steps to get back
to Doodling.
TAKE A BREAK:
Power Adapter
x2
BLUE
light
PLA
Plastic
1
2
4
3
1
3
2
3Doodler_Bob_User_Manual_MAIN_Inner_20180511.indd 7 11/5/2018 11:37 AM
8
Step 7: Let’s Switch to PLA Plastic!
PLA Plastic
ABS Plastic
The color of the Plastic will
change once the PLA starts
extruding. It will appear mixed
at rst. STOP extrusion by
pushing either button once.
SLOW
FAST
Click FAST or SLOW once to
continue extruding the PLA
Plastic and Doodle as you wish.
Step 8: Power Down
Move the Control Switch
to OFF.
After 5 minutes of inactivity, the 3Doodler Create+’s heating
system will automatically power down. You will need to press one
of the Speed Buttons OR toggle the Control Switch OFF and then
ON again to continue use.
SECTION 3: TROUBLESHOOTING
Tools (Provided in Box)
Before showing you how to troubleshoot issues
with your 3Doodler Create+, we want to introduce
you to three handy tools provided in your box:
Mini Spanner
Used for tightening and
removing the Nozzle.
Do not remove Nozzle
when Pen is cold.
Do not overtighten the
Nozzle, as you may
break it.
Unblocking Tool
Used for pushing short
pieces of Plastic down
into the Drive Gear to
help with extrusion
from Pen.
Mini Screwdriver
Keep this handy
for removing the
Maintenance Cover.
Keep this handy
for removing the
Maintenance Cover
or rotating the
Temperature Adjuster
(See the3doodler.com/
temperature)
With those introductions over, it’s time to look
at the dierent issues that may arise with your
3Doodler Create+ and steps to get back
to Doodling.
3Doodler_Bob_User_Manual_MAIN_Inner_20180511.indd 8 11/5/2018 11:37 AM
9
1. My Pen won’t turn on!
(Light doesn’t turn on)
Let’s double check the following:
A. Is the Power Adapter plugged into a working power outlet?
B. Is the end of the Power
Adapter connected to the
correct part of the Pen?
If you have a spare power adapter around the house please
use it to test your 3Doodler Create+. This will help determine if
the problem is with your 3Doodler Create+ or with the Power
Adapter provided in the box.
NOTE:
C. Make sure the Control
Switch on your 3Doodler
Create+ is not set to OFF.
3. My Plastic is not extruding from
my 3Doodler Create+.
3A. Plastic not engaging properly with the Drive Gear:
Gently push until you feel the strand pulled through the Drive
Gear on its own.
If the above does not work, reverse the Plastic fully from the Pen.
(See Section 2, Step 6) Snip ends, then reinsert and try again.
If Plastic is too short to be removed from the Pen, move to 3B.
3B. Plastic is too short to be removed from the Pen:
Try unscrewing the Nozzle and
using the Unblocking Tool.
While Pen is hot (BLUE or
GREEN Light on), use Mini
Spanner to unscrew and
remove Nozzle anti-clockwise.
While using the Reverse feature
of the 3Doodler Create+, insert
Unblocking Tool through open
front end of Pen and gently
push any excess Plastic out
through the back of the Pen.
Mini
Spanner
BLUE
or
GREEN
Light
3C. Plastic may be wrapped
around the Drive Gear.
Remove Maintenance Cover
using Mini Screwdriver
provided in the box.
Use the Mini Screwdriver
or Unblocking Tool to lift
and release Plastic from the
Drive Gear and out of the Pen
through the open area beneath
the Maintenance Cover or
from the Plastic Loading Port.
2. My Plastic is extruding but it
won’t stick to the paper, or is
curling up around the Nozzle.
Stop extruding and start
again using the following
instructions:
When the Plastic resumes
extruding, push the Nozzle
rmly down into the paper,
allowing Plastic to stick to the
surface.
Drag the Plastic along the
paper or surface in a continuous
unbroken line as if you were
writing with a pencil.
Keep your movement slow and
steady. The Plastic should hold
to the paper and not curl up
around the Nozzle.
Blue or
Green
Light
Unblocking
Tool
Nozzle may loosen with
continued usage (or in transit).
While Pen is hot (BLUE or
GREEN Light on), gently turn
Nozzle clockwise to tighten
it using the Mini Spanner
provided. Stop tightening once
you rst feel resistance so as
to avoid over-tightening the
Nozzle and breaking it.
A. Click either the FAST or SLOW button once.
B. If Step A does not solve this problem, please unplug your
3Doodler Create+ and then plug it in and try again.
5. My Plastic won’t stop extruding.
4. My Plastic is leaking from
around the Nozzle.
While the Pen is on and hot (BLUE or GREEN Light), double click
either the FAST or SLOW button. Light will start ashing to signal
the Plastic is reversing. Once the Plastic stops reversing, it is safe
to remove it from the Pen by gently pulling on the back of the
strand.
If Plastic is too short to reverse, see Section 3, Step 3B.
6. How do I reverse my
unused Plastic?
It is possible that the Plastic is either too short to reverse all the
way out of your 3Doodler Create+, or that the Plastic has moved
past the Pen’s Drive Gear system.
You will be able to check for these issues by looking through the
Maintenance Cover.
7. I have reversed my Plastic but
cannot get it out.
For both of these issues, you can try the following options:
Insert a new strand of Plastic or Unblocking Tool to push the
remaining Plastic through while Pen is ON and extruding.
Plastic reversed, but too short to take out and no longer in
contact with the Drive Gear.
Plastic is beyond Drive Gear.
Or
While using the Reverse feature of the 3Doodler Create+, remove
Nozzle and use Unblocking Tool to push Plastic out the back of
the Pen. (See Section 3, Step 3B).
3Doodler_Bob_User_Manual_MAIN_Inner_20180511.indd 9 11/5/2018 11:37 AM
10
1. My Pen won’t turn on!
(Light doesn’t turn on)
A. Is the Power Adapter plugged into a working power outlet?
If you have a spare power adapter around the house please
use it to test your 3Doodler Create+. This will help determine if
the problem is with your 3Doodler Create+ or with the Power
Adapter provided in the box.
C. Make sure the Control
Switch on your 3Doodler
Create+ is not set to OFF.
3. My Plastic is not extruding from
my 3Doodler Create+.
3A. Plastic not engaging properly with the Drive Gear:
Gently push until you feel the strand pulled through the Drive
Gear on its own.
If the above does not work, reverse the Plastic fully from the Pen.
(See Section 2, Step 6) Snip ends, then reinsert and try again.
If Plastic is too short to be removed from the Pen, move to 3B.
3B. Plastic is too short to be removed from the Pen:
3C. Plastic may be wrapped
around the Drive Gear.
Remove Maintenance Cover
using Mini Screwdriver
provided in the box.
Use the Mini Screwdriver
or Unblocking Tool to lift
and release Plastic from the
Drive Gear and out of the Pen
through the open area beneath
the Maintenance Cover or
from the Plastic Loading Port.
Mini
Screwdriver
2. My Plastic is extruding but it
won’t stick to the paper, or is
curling up around the Nozzle.
Maintenance
Cover
Blue or
Green
Light
Unblocking
Tool
Nozzle may loosen with
continued usage (or in transit).
While Pen is hot (BLUE or
GREEN Light on), gently turn
Nozzle clockwise to tighten
it using the Mini Spanner
provided. Stop tightening once
you rst feel resistance so as
to avoid over-tightening the
Nozzle and breaking it.
A. Click either the FAST or SLOW button once.
B. If Step A does not solve this problem, please unplug your
3Doodler Create+ and then plug it in and try again.
5. My Plastic won’t stop extruding.
4. My Plastic is leaking from
around the Nozzle.
While the Pen is on and hot (BLUE or GREEN Light), double click
either the FAST or SLOW button. Light will start ashing to signal
the Plastic is reversing. Once the Plastic stops reversing, it is safe
to remove it from the Pen by gently pulling on the back of the
strand.
If Plastic is too short to reverse, see Section 3, Step 3B.
6. How do I reverse my
unused Plastic?
Snip the ends of your Plastic now for easier loading
and Doodling later.
It is possible that the Plastic is either too short to reverse all the
way out of your 3Doodler Create+, or that the Plastic has moved
past the Pen’s Drive Gear system.
You will be able to check for these issues by looking through the
Maintenance Cover.
7. I have reversed my Plastic but
cannot get it out.
For both of these issues, you can try the following options:
Insert a new strand of Plastic or Unblocking Tool to push the
remaining Plastic through while Pen is ON and extruding.
Plastic reversed, but too short to take out and no longer in
contact with the Drive Gear.
TIP
Mini
Spanner
Plastic is beyond Drive Gear.
Or
While using the Reverse feature of the 3Doodler Create+, remove
Nozzle and use Unblocking Tool to push Plastic out the back of
the Pen. (See Section 3, Step 3B).
Unblocking Tool
3Doodler_Bob_User_Manual_MAIN_Inner_20180511.indd 10 11/5/2018 11:37 AM
11
It takes around 60-90 seconds for your Pen to heat up. If, after
that time, the Pen still does not heat up and the Light remains
RED, turn the Pen ON and OFF and try again. If that still does not
work, please contact us at [email protected] and we will
assist further.
8. My Pen won’t heat up!
(light stays red).
SECTION 4: TIPS AND BEST
PRACTICES
For optimal Doodling, we suggest using the correct temperature
settings for your Plastic.
DO double check which type of Plastic you are using before you
turn on the 3Doodler Create+ and insert a Plastic strand. If your
Plastic strands get mixed up, here is a handy table for sorting and
identifying what you’re working with.
Pay attention to Plastic types
and settings
ABS (MATTE):
Temp: ABS / FLX Temp
Light: BLUE
Feature: Great for drawing in the air.
How to tell: Plastic has white
semi-circle ends.
PLA (GLOSSY / CLEAR /
METALLIC / SPARKLE ):
Temp: PLA Temp
Light: GREEN
Feature: Gossy and making it perfect
for artistic creations.
How to tell: Very rigid, no white
semi-circle ends.
FLEXY:
Temp: ABS / FLX Temp
Light: BLUE
Feature: Make exible,
bendable Doodles.
How to tell: Plastic is very exible.
Unsnipped Ends
VS
Snipped Ends
DO give your 3Doodler Create+ a rest after every 2 hours of
continuous Doodling. 30 minutes of down time should be plenty.
Once the Plastic stops reversing, it is safe to remove it from the
Pen by gently pulling on the back of the strand.
If you ever remove your
Nozzle, DO NOT remove it
when your 3Doodler Create+
is cold. Light should be BLUE
or GREEN.
If you ever need to tighten
your Nozzle, DO NOT force
the Nozzle or overtighten it,
as you could break the Nozzle
and permanently damage your
3Doodler Create+.
Treat your Nozzle right
Do not forget to snip your
Plastic ends
Take a break
After removing a Plastic strand
from the 3Doodler Create+, cut
and remove any partially melted
material at the end of your
strand before re-feeding it into
the 3Doodler Create+. This will
reduce blockages or clogging
issues.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the lim-
its for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
CAN ICES-3 (B)/NMB-3(B)
SPECIFICATIONS
Output Power: 6W
Output Voltage: 5V
Input Voltage: 5V
CARE & MAINTENANCE
For care and maintenance information, and more advice on how to use your
3Doodler, please refer to our website: the3Doodler.com
To troubleshoot, please visit: the3Doodler.com/troubleshooting
This marking indicates that this product should not be disposed of with
other household wastes. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, recycle it responsibly to
promote the sustainable reuse of material resources.
LIMITED WARRANTY
For more details on your limited warranty, pleae visit:
the3Doodler.com/warranty
For 3DoodlerÕs Terms and Conditions and other notices please refer to our
website: the3Doodler.com/terms-and-conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
SPECIFICATION OF POWER ADAPTER
Input: 100-240V AC, 0.5A MAX, 50-60Hz
Output: +5V DC, 1.2A
CARE & MAINTENANCE
For care and maintenance information, and more advice on how to use your
3Doodler Create+, please refer to our website: the3Doodler.com
To troubleshoot, please visit: the3Doodler.com/troubleshooting
LIMITED WARRANTY
For more details on your limited warranty, please visit:
the3Doodler.com/warranty
For 3Doodler’s Terms and Conditions and other notices please refer to our
website: the3Doodler.com/terms-and-conditions
Specications are subject to change and improvement without notice.
DO NOT pull Plastic from the back of the 3Doodler Create+
other than as directed.
Double click either Speed
Button and the Light will start
ashing to signal the Plastic is
reversing.
With the Pen set to ABS / FLX,
wait for the BLUE Light to
come on.
Reverse and remove Plastic
correctly
BLUE Light
x2
Flashing
BLUE
1 2
3Doodler_Bob_User_Manual_MAIN_Inner_20180511.indd 11 11/5/2018 11:37 AM
12
It takes around 60-90 seconds for your Pen to heat up. If, after
that time, the Pen still does not heat up and the Light remains
RED, turn the Pen ON and OFF and try again. If that still does not
work, please contact us at [email protected] and we will
assist further.
8. My Pen won’t heat up!
(light stays red).
SECTION 4: TIPS AND BEST
PRACTICES
For optimal Doodling, we suggest using the correct temperature
settings for your Plastic.
DO double check which type of Plastic you are using before you
turn on the 3Doodler Create+ and insert a Plastic strand. If your
Plastic strands get mixed up, here is a handy table for sorting and
identifying what you’re working with.
Pay attention to Plastic types
and settings
Snipped Ends
DO give your 3Doodler Create+ a rest after every 2 hours of
continuous Doodling. 30 minutes of down time should be plenty.
Once the Plastic stops reversing, it is safe to remove it from the
Pen by gently pulling on the back of the strand.
If you ever remove your
Nozzle, DO NOT remove it
when your 3Doodler Create+
is cold. Light should be BLUE
or GREEN.
If you ever need to tighten
your Nozzle, DO NOT force
the Nozzle or overtighten it,
as you could break the Nozzle
and permanently damage your
3Doodler Create+.
Treat your Nozzle right
Do not forget to snip your
Plastic ends
Take a break
BLUE or
GREEN Light
3
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the lim-
its for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
CAN ICES-3 (B)/NMB-3(B)
This marking indicates that this product should not be disposed
of with other household wastes. To prevent possible harm to the
environment or human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable reuse of material
resources.
SPECIFICATIONS
Output Power: 6W
Output Voltage: 5V
Input Voltage: 5V
CARE & MAINTENANCE
For care and maintenance information, and more advice on how to use your
3Doodler, please refer to our website: the3Doodler.com
To troubleshoot, please visit: the3Doodler.com/troubleshooting
This marking indicates that this product should not be disposed of with
other household wastes. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, recycle it responsibly to
promote the sustainable reuse of material resources.
LIMITED WARRANTY
For more details on your limited warranty, pleae visit:
the3Doodler.com/warranty
For 3DoodlerÕs Terms and Conditions and other notices please refer to our
website: the3Doodler.com/terms-and-conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
SPECIFICATION OF POWER ADAPTER
Input: 100-240V AC, 0.5A MAX, 50-60Hz
Output: +5V DC, 1.2A
CARE & MAINTENANCE
For care and maintenance information, and more advice on how to use your
3Doodler Create+, please refer to our website: the3Doodler.com
To troubleshoot, please visit: the3Doodler.com/troubleshooting
LIMITED WARRANTY
For more details on your limited warranty, please visit:
the3Doodler.com/warranty
For 3Doodler’s Terms and Conditions and other notices please refer to our
website: the3Doodler.com/terms-and-conditions
Specications are subject to change and improvement without notice.
DO NOT pull Plastic from the back of the 3Doodler Create+
other than as directed.
Double click either Speed
Button and the Light will start
ashing to signal the Plastic is
reversing.
Reverse and remove Plastic
correctly
3Doodler_Bob_User_Manual_MAIN_Inner_20180511.indd 12 11/5/2018 11:37 AM
84
3Doodler Create+: Australia 2013101514; China ZL201310535754.2,
ZL201320686485.5, ZL201430565974.5; Germany 202013010264.0,
202013011820.2; European Community 002607234-0001; Hong Kong
1185219, 1402448.7M001, 1402448.7M002, 1402448.7M003, 1402448.7M004;
Japan 1534061; Korea 30-0821455; Mexico 3553; Taiwan M502562, D172860;
United States of America D749173, D789453; and other patents pending.
This product is protected by WobbleWorks’ intellectual property. Please see
the list of Wobbleworks’ patents at / Ce produit est protégé par la propriété
intellectuelle de WobbleWorks. S’il vous plaît voir la liste des brevets de
Wobbleworks à / Este producto está protegido por propiedad intelectual y
pertenece a WoobleWorks. Consulte la lista de patentes de
WoobleWorks en / Dieses Produkt ist durch WobbleWorks‘ geistiges Eigentum
geschützt. Sie nden die Liste von Wobbleworks‘ Patenten unter / Dit
product valt onder de bescherming van het intellectueel eigendomsrecht van
WobbleWorks. Raadpleeg de lijst met Wobbleworks’ octrooien op / 本产品受
WobbleWorks知识产权保护。 请参阅Wobbleworks的专利列表 / Questo
prodotto è protetto dalla proprietà intellettuale di WobbleWorks. Si prega di
consultare l’elenco dei brevetti di Wobbleworks all’indirizzo :
http://the3Doodler.com/patents.
3Doodler_Bob_User_Manual_MAIN_Inner_20180511.indd 84 11/5/2018 11:38 AM
Getting the most out of your
Holen Sie das Meiste heraus aus Ihrem
Tirez le meilleur de votre
Aprovecha al máximo tu
Come utilizzare al meglio la
Haal het meeste uit je
Hello Bienvenue Bienvenido
Willkommen Benvenuti Hallo
EN
FR
ES
DE
IT
NL
Revised: May 11, 2018
Manufactured by / Fabriqué par / Fabricado por / Hergestellt von /
Fabbricato da / Gemaakt door WobbleWorks (HK) Limited.
Distributed by / Distribué par / Distribuido por / Vertrieben von /
Distribuito da / Gedistribueerd door WobbleWorks,Inc. /
WobbleWorks (HK) Limited, 89 5th Avenue, Suite 802, NY, NY, 10003.
© WobbleWorks, Inc. 2018
3Doodler_Bob_User_Manual_MAIN_Cover_&Back_20180511.indd 1 14/5/2018 9:45 AM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15

3Doodler 8CPSBKUS3E Manuale utente

Tipo
Manuale utente

in altre lingue