Lexmark 20T3650 - T 620n B/W Laser Printer Manuale utente

Lexmark T620 and T622

2000-Sheet Drawer

User’s Guide

Gaveta de 2000 folhas

Guia do usuário

Tiroir 2000 feuilles

Manuel d’utilisation

2000-Blatt-Zuführung

Benutzerhandbuch

Cassetto da 2000 fogli

Guida per l’utente

Alimentador de 2000 hojas

Guía del usuario

 







































English

First Edition (January 2001)

The following paragraph does not apply to any country where such provisions are inconsistent with

local law: LEXMARK INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT

WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO,

THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions;

therefore, this statement may not apply to you.

This publication could include technical inaccuracies or typographical errors. Changes are periodically made

to the information herein; these changes will be incorporated in later editions. Improvements or changes in the

products or the programs described may be made at any time.

References in this publication to products, programs, or services do not imply that the manufacturer intends to

make these available in all countries in which it operates. Any reference to a product, program, or service is not

intended to state or imply that only that product, program, or service may be used. Any functionally equivalent

product, program, or service that does not infringe any existing intellectual property right may be used instead.

Evaluation and verification of operation in conjunction with other products, programs, or services, except

those expressly designated by the manufacturer, are the user’s responsibility.

Lexmark is a trademark of Lexmark International, Inc., registered in the United States and/or other countries.

Other trademarks are the property of their respective owners.

UNITED STATES GOVERNMENT RESTRICTED RIGHTS. This software and documentation are

provided with RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to

restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software

clause at DFARS 252.227-7013 and in applicable FAR provisions: Lex-mark International, Inc., Lexington,

KY 40550.

2000-Sheet Drawer User’s Guide

Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Unpacking the 2000-Sheet Drawer . . . . . . . . . . . . . . . 2

Attaching Stabilizer Feet . . . . . . . . . . . . . . . . . . . . . . . 3

Installing the 2000-Sheet Drawer. . . . . . . . . . . . . . . . . 6

Verifying Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Setting the Paper Type . . . . . . . . . . . . . . . . . . . . . . . 11

Changing the Paper Size . . . . . . . . . . . . . . . . . . . . . . 12

Selecting Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Loading Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Clearing a Paper Jam . . . . . . . . . . . . . . . . . . . . . . . . 20

2000-Sheet Drawer User’s Guide

1

Introduction

The 2000-sheet drawer gives your printer added capacity by allowing you to load

up to four reams (approximately 2,000 sheets) of 20 lb paper.

Your drawer is pre-configured to either letter or A4 paper size. To use a different

paper size, see page 12.

Your printer has an autoconnect feature that recognizes when the 2000-sheet

drawer has been installed. After starting your printer, this option is shown as Tray

2, Tray 3, Tray 4 or Tray 5, depending upon the number of installed paper

sources.

To ensure reliable paper feeding, it is important that you select paper

recommended for use with the 2000-sheet drawer and that you load it properly.

See page 14 for information on paper specifications and page 16 for loading

instructions.

To ensure compatibility with your printer, verify your drawer is labeled with a

colored triangle located on the top left front corner.

Refer to your printer documentation for information pertaining to electronic

emissions, safety, and warranty.

2000-Sheet Drawer User’s Guide

2

Unpacking the 2000-Sheet Drawer

1 Remove all items shown in the illustration from the carton. If any items are

missing, contact the place where you bought the 2000-sheet drawer.

Note: The 16 AWG power cord is included only with units

intended to operate at 100 - 127V power.

2 Remove all packing material and tape from each item.

Note: Save the carton and packing material in case you

need to repack the 2000-sheet drawer for service or

storage.

3 Peel the appropriately numbered decals from the sheet and attach them to

the recessed areas on the drawer. Choose the number that corresponds to

the number of paper options you are attaching, including the standard

input tray.

Stabilizer feet

16 AWG power

Decals

2000-sheet

Jumper cord

Printer compatibility

label (colored triangle)

2000-Sheet Drawer User’s Guide

3

Attaching Stabilizer Feet

CAUTION! If you are not using an optional printer stand, the four stabilizer

feet must be attached to the drawer.

1 Carefully invert the 2000-sheet drawer so the bottom faces up.

2 Remove the screws securing the rubber feet to the drawer. Save the

screws and rubber feet for use in step 5 on page 5.

Note: If you later choose to use the drawer with the printer

stand, you must remove the stabilizer feet and re-

attach the rubber feet.

2000-Sheet Drawer User’s Guide

4

3 Insert the tab on the end of the stabilizer foot into the slot on the bottom of

the drawer. Rotate the stabilizer foot down until it is aligned with the bottom

of the drawer.

4 Slide the foot away from the center of the tray until it locks into place.

2000-Sheet Drawer User’s Guide

5

5 Using one of the rubber feet removed in step 2 on page 3, align the

openings of the rubber and stabilizer feet and attach the screw as shown.

6 Repeat step 3 on page 4 through step 5 on page 5 for the remaining

rubber and stabilizer feet.

2000-Sheet Drawer User’s Guide

6

Installing the 2000-Sheet Drawer

Decide on an installation location for the 2000-sheet drawer. The printer, and

possibly other options, will be placed on top of the drawer, so allow a maximum of

137.16 cm (4 ½ ft) for clearance.

Note: Your drawer is pre-configured to either letter or A4 paper size.

To use a different paper size, see page 12 before placing any

options or the printer on the 2000-sheet drawer.

1 Turn the printer power off and unplug the power cord.

2 Disconnect any other cables attached to the printer.

3 Place any options you may have on top of the drawer one at a time. Refer

to your printer documentation for proper installation instructions.

4 Ask someone to help you lift the printer and position it above the drawer

and any options you may have installed in step 3.

CAUTION! Make sure your fingers are not under the printer when you set it

down. Use the handholds on the printer or ask someone to help

you lift it.

2000-Sheet Drawer User’s Guide

7

5 Place the printer on top of the drawer and any options installed. The

openings on top of the drawer will help you set the printer so the edges are

aligned properly. Make sure the printer is securely in place.

Handhold

Square hole

Tab

Round hole

2000-Sheet Drawer User’s Guide

8

6 Plug the jumper cord into the printer. Plug the other end of the jumper cord

into the drawer.

7 Reconnect any disconnected cables.

2000-Sheet Drawer User’s Guide

9

8 If you intend to operate your 2000-sheet drawer at 100 - 127V power, you

must use the 16 AWG power cord provided with the unit. Plug the 16 AWG

power cord into the back of the drawer and then into a properly grounded

electrical outlet. Do not use the power cord provided with the printer;

however, you may retain it for possible future use. For example, if you later

decide to detach the current printer from the 2000-sheet drawer, and use

the printer with other paper options, you should use the original power cord

provided with the printer. The 16 AWg power cord should always remain

with the 2000-sheet drawer.

If you intend to operate your 2000-sheet drawer at 200 -

240V power, use the power cord provided with the printer.

Plug the power cord into the back of the drawer and then

into a properly grounded electrical outlet.

2000-Sheet Drawer User’s Guide

10

Verifying Installation

Once the 2000-sheet drawer has been installed, verify that it is installed properly

by printing a menu settings page.

To print a menu settings page:

1 Make sure the printer power is on and the Ready status message appears

on the display.

2 Press Menu to access the menus.

3 Continue to press and release Menu until Utilities Menu appears on the

display.

4 Press Select to show the list of available menu items for the Utilities Menu.

Utilities Menu now appears on the first line of the display.

5 Press and release Menu until Print Menus appears on the second line of

the display.

6 Press Select to select Print Menus. The message Printing Menu

Settings is displayed.

The menu settings page prints.

Installed Features on the menu settings page lists all options that have been

installed.

Look for 2000-sheet drawer on the printed page. If the drawer is listed, you are

ready to begin using it.

If the drawer is not listed on the page, the printer or other options may not be

seated securely or aligned properly. Return to page 6 of this guide and carefully

follow all installation instructions. Print the menu settings page again to verify

installation.

2000-Sheet Drawer User’s Guide

11

Setting the Paper Type

Once the drawer is installed, you should set the paper type. To set the paper type,

go to the printer operator panel, and then follow these steps:

1 Make sure the printer power is on and the Ready status message appears

on the display.

2 Press Menu to access the menus.

3 Continue to press and release Menu until Paper Menu appears on the

display.

4 Press Select to access the Paper Menu.

5 Continue to press and release Menu until Paper Type appears on the

display.

6 Press Select to show the list of available menu items for the Paper Type

menu.

7 Continue to press and release Menu until Tray x Type (where x represents

the tray number of the 2000-sheet drawer) appears on the display.

8 Press Select to show the list of available menu items for Tray x Type.

9 Continue to press and release Menu until the paper type you are using in

the 2000-sheet drawer appears on the display.

10 Press Select to select the paper type.

Note: You may select any operator panel feature available

except Paper Type = Transparency.

11 Press Go to display the Ready status message.

2000-Sheet Drawer User’s Guide

12

Changing the Paper Size

Your 2000-sheet drawer comes pre-configured for either letter or A4 paper size.

To change the paper size prior to installation, proceed to step 7 of the following

instructions now. If you are changing the paper size for a unit that is already

attached to a printer and a power source, proceed with step 1:

1 Open the loading door.

2 Push the elevator down button located on the left side of the door opening.

See illustration on page 17.

3 Remove paper from the elevator tray and close the loading door.

4 Re-open the door. The printer elevator tray should be approximately

halfway up.

5 Unplug the power cord.

6 Remove the printer and all attached options from the

2000-sheet drawer.

CAUTION! Remove the attached options one at a time. Make sure your fin-

gers are not under the printer when you set it down. Use the

handholds on the printer or ask someone to help you lift it.

7 Locate the paper size selector knob on top of the drawer. See page 12 for

an illustration and location of the knob.

Note: Six paper selections are available. Each paper selection is

color-coded. A new paper size is displayed on the operator

panel after the paper elevator tray is in the up position.

8 To make a selection, turn the knob completely in a counterclockwise

direction. This action sets the paper size to legal (LGL).

9 Count the clicks as you turn the knob clockwise to find the correct

paper size. For example, one click sets the paper size to executive

(EXEC).

2000-Sheet Drawer User’s Guide

13

Note: Make a note of the color associated with the paper size you

select.

Paper size selector knob

2000-Sheet Drawer User’s Guide

14

10 Pull each locking pin up to unlock it, and then pull up on the guides to

remove them.

11 Reposition the paper guides in the color-coded slots, located at the top of

the unit, corresponding to the paper size you selected.

12 Insert the paper guides into the matching colored slots located on the

inside bottom of the unit. The guides should now be seated flush against

the top of the unit.

13 Push each pin down to lock the guides in place.

Selecting Paper

The print quality and feeding reliability of your printer can vary with the type of

paper you use. For more detailed information about paper specifications, refer to

your printer documentation.

Locking pins

Side guides

Back guide

Color-coded slots

(bottom)

Color-coded slo

t

(top)

La pagina sta caricando ...

Lexmark 20T3650 - T 620n B/W Laser Printer Manuale utente

Questo manuale è adatto anche per

Lexmark 20T3650 - T 620n B/W Laser Printer Manuale utente

in altre lingue

Documenti correlati

Altri documenti