Husqvarna 136 LiHD50 Manuale del proprietario

EE

nn

gg

ll

ii

ss

hh

136 LiHD50

GB

Oper

ator’

s man

ual 2-23

SE

Br

uksan

visning 24-45

DK

Br

ugsan

visning 46-67

NO

Br

uksan

visning 68-89

FI

Käyttöohje 90-111

DE

Bedien

ungsanw

eisung 112-134

FR

Man

uel d’utilisation 135-157

NL

Gebr

uiksaanwijzing 158-179

ES

Man

ual de instr

ucciones 180-201

PT

Instr

uções par

a o uso 202-223

IT

Istr

uzioni per l’uso 224-245

H1154526-38,136 LiHD50,_1 v2.fm Page 1 Friday, February 10, 2012 3:20 PM

KEY

T

O SYMBOLS

2

–

English

Symbols on the mac

hine:

T

ranslation of the original Swedish operating instruction.

WARNING! Incorrect or

careless use of a hedge

trimmer can turn it into a

dangerous tool that can

cause serious or even

fatal injury. It is extremely

important that you read

and understand the contents of this operator's manual.

Always wear:

• Approved hearing protection

• Approved eye protection

This product is in accordance with

applicable EC directives.

Always wear approved protective

gloves.

Wear sturdy, non-slip boots.

Symbols on the product or its

packaging indicate that this product

cannot be handled as domestic

waste. This product must be

deposited at an appropriate

recycling facility.

Cutting tool. Do not touch the tool

without ﬁrst deactivating the

machine.

Do not expose to rain.

Direct current

Noise emission to the environment

according to the European Community’s

Directive. The machine’s emission is

speciﬁed in the Technical data chapter

and on the label.

Symbols on the batter

y and on

the battery charger:

This product

must be

deposited at an

appropriate

recycling

facility.

Fail-safe transformer

Use and store battery charger only

indoors.

Double insulation

Other symbols/decals on the mac

hine refer to special

certiﬁcation requirements for certain markets.

Symbols in the operator’

s

manual:

The machine is turned on and off by

pressing the on and stop button.

Always wear approved protective

gloves.

Regular cleaning is required.

Visual check.

Protective goggles or a visor must be

worn.

Remove the battery. IMPORTANT!

Always remove the battery to prevent

the machine being started by accident.

Li-ion

H1154526-38,136 LiHD50,_1 v2.fm Page 2 Friday, February 10, 2012 3:20 PM

KEY

T

O SYMBOLS

English

–

3

Y

ou will ﬁnd the following labels on your hedge trimmer,

battery and battery charger:

Husqvarna 136 LiHD50 578 46 36-01

s/n XXXX XXXXXXX

36V

Husqvarna AB

Huskvarna SWEDEN

H1154526-38,136 LiHD50,_1 v2.fm Page 3 Friday, February 10, 2012 3:20 PM

CONTENTS

4

–

English

Contents

Note the f

ollowing before

starting:

Please read the oper

ator's manual carefully.

KEY

TO SYMBOLS

Symbols on the machine:

...................................... 2

Symbols on the battery and on the battery charger:

2

Symbols in the operator’s manual: ........................ 2

CONTENTS

Contents

............................................................... 4

Note the following before starting: ........................ 4

INTR

ODUCTION

Dear Customer

, ..................................................... 5

WHA

T IS WHAT?

What is what?

....................................................... 6

GENERAL SAFETY PRECA

UTIONS

Gener

al power tool safety warnings ...................... 7

Personal protective equipment ............................. 9

Battery and battery charger .................................. 9

Machine

′

s safety equipment ................................. 11

B

ATTERY HANDLING

Batter

y .................................................................. 13

Battery charger ..................................................... 13

Transport and storage ........................................... 14

Disposal of the battery, battery charger and

machine ................................................................

14

ST

ARTING AND STOPPING

Chec

k before starting ............................................ 15

Connect battery to the machine ............................ 15

Starting and stopping ............................................ 15

W

ORKING TECHNIQUES

Gener

al working instructions ................................ 17

MAINTENANCE

Inspection and maintenance

................................. 19

Cleaning and lubrication ....................................... 19

Troubleshooting schedule ..................................... 20

Maintenance schedule .......................................... 21

TECHNICAL D

ATA

T

echnical data ....................................................... 22

EC-declaration of conformity ................................ 23

!

W

ARNING! Long-term exposure to noise

can result in permanent hearing

impairment. So always use approved

hearing protection.

!

W

ARNING! Under no circumstances may

the design of the machine be modiﬁed

without the permission of the

manufacturer. Always use original

accessories. Non-authorized

modiﬁcations and/or accessories can

result in serious personal injury or the

death of the operator or others.

!

W

ARNING! Incorrect or careless use of a

hedge trimmer can turn it into a

dangerous tool that can cause serious or

even fatal injury. It is extremely important

that you read and understand the

contents of this operator's manual.

H1154526-38,136 LiHD50,_1 v2.fm Page 4 Friday, February 10, 2012 3:20 PM

English

–

5

INTR

ODUCTION

Dear Customer

,

Cong

ratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689,

when the Swedish King Karl XI ordered the construction of a factory on the banks of the Husqvarna River, for production

of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-

powered plant. During the more than 300 years in existence, the Husqvarna factory has produced a lot of different

products, from wood stoves to modern kitchen appliances, sewing machines, bicycles, motorcycles etc. In 1956, the ﬁrst

motor driven lawn mowers appeared, followed by chain saws in 1959, and it is within this area Husqvarna is working

today.

Today Husqvarna is one of the leading manufacturers in the world of forest and garden products, with quality as our

highest priority. The business concept is to develop, manufacture and market motor-driven products for forestry and

gardening, as well as for the building and construction industry. Husqvarna

′

s aim is also to be at the front edge for

ergonomics, usability, security and environmental protection. That is the reason why we have developed many different

features to add to our products within these areas.

We are convinced that you will appreciate with great satisfaction the quality and performance of our product for a very

long time to come. The purchase of one of our products gives you access to professional help with repairs and service

whenever this may be necessary. If the retailer who sells your machine is not one of our authorised dealers, ask for the

address of your nearest service workshop.

It is our wish that you will be satisﬁed with your product and that it will be your companion for a long time. Think of this

operator

′

s manual as a valuable document. By following its content (usage, service, maintenance, etc), the life span and

the second-hand value of the machine can be extended. If you sell this machine, make sure that the operator

′

s manual

is passed on to the buyer.

Thank you for using a Husqvarna product.

Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and

appearance of products without prior notice.

H1154526-38,136 LiHD50,_1 v2.fm Page 5 Friday, February 10, 2012 3:20 PM

6

–

English

WHA

T IS

WHA

T?

What is what?

10

1

2

3

4

5

6

7

9

11

12

16

17

13

15

14

15

18

8

19

1

Operator

′

s manual

2 Rear handle

3 Power trigger lockout

4 Front handle

5 Cutter

6 Transport guard

7 Power trigger

8 Control panel

9 Hand guard

10 Battery

11 Battery charger

12 Cord

13 Battery indicator button

14 Battery status

15 Warning indicator

16 SavE button

17 Activate and deactivate button

18 Power on and warning indicator

19 Battery release buttons

H1154526-38,136 LiHD50,_1 v2.fm Page 6 Friday, February 10, 2012 3:20 PM

GENERAL SAFETY PRECA

UTIONS

English

–

7

General po

wer tool safety

warnings

Please read the oper

ator’s manual carefully and make

sure you understand the instructions before using the

machine.

The machine is only designed for cutting branches and

twigs.

Always remove the battery to prevent the machine being

started by accident.

W

ork area safety

•

Keep work area clean and well lit.

Cluttered or dark

areas invite accidents.

•

Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂammable liquids, gases or dust.

Power tools

create sparks which may ignite the dust or fumes.

•

Keep children and bystanders away while

operating a power tool.

Distractions can cause you

to lose control.

Electrical saf

ety

•

Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools.

Unmodiﬁed plugs and matching outlets will

reduce the risk of electric shock.

•

Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators.

There is an increased risk of electric

shock if your body is earthed or grounded.

•

Do not expose power tools to rain or wet

conditions.

Water entering a power tool will increase

the risk of electric shock.

•

Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts.

Damaged or entangled cords increase

the risk of electric shock.

•

When operating a power tool outdoors, use an

extension cord suitable for outdoor use.

Use of a

cord suitable for outdoor use reduces the risk of

electric shock.

•

If operating a power tool in a damp location is

unaviodable, use a residual current device (RCD)

protected supply.

Use of an RCD reduces the risk of

electric shock.

Personal safety

• Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the inﬂuence of drugs, alcohol or medication.

A

moment of inattention while operating power tools

may result in serious personal injury.

• Use personal protective equipment. Always wear

eye protection.

Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personal injuries.

• Prevent unintentional starting. Ensure the switch

is in the OFF-position before connecting to a

power source and/or battery pack, picking up or

carrying the tool.

Carrying power tools with your

ﬁnger on the switch or energising power tools that

have the switch on invites accidents.

• Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left

attached to a rotating part of the power tool may result

in personal injury.

• Do not overreach. Keep proper footing and

balance at all times.

This enables better control of

the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts.

Loose clothes, jewellery or

long hair can be caught in moving parts.

• If devices are provided for the connection of dust

extraction and collection facilities, ensure these

are connected and properly used.

Use of dust

collection can reduce dust-related hazards.

• The vibration emission during actual use of the power

tool can differ from the declared total value depending

on the ways in which the tool is used. Operators

should identify safety measures to protect themselves

that are based on an estimation of exposure in the

actual conditions of use (taking account of all parts of

the operating cycle such as the times when the tool is

switched off and when it is running idle in addition to

the trigger).

Power tool use and care

• Do not force the power tool. Use the correct power

tool for your application.

The correct power tool will

do the job better and safer at the rate for which it was

designed.

• Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be

repaired.

!

WARNING! Read all safety warnings and

all instructions. Failure to follow the

warnings and instructions may result in

electric shock, ﬁre and/or serious injury.

IMPORTANT!

Save all warnings and instructions for future reference.

The term ”power tool” in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

H1154526-38,136 LiHD50,_1 v2.fm Page 7 Friday, February 10, 2012 3:20 PM

GENERAL SAFETY PRECAUTIONS

8 – English

• Disconnect the plug from the power source and/or

the battery pack from the power tool before

making any adjustments, changing accessories,

or storing power tools.

Such preventive safety

measures reduce the risk of starting the power tool

accidentally.

• Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool.

Power tools are dangerous in the hands

of untrained users.

• Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and

any other condition that may affect the power

tool´s operation. If damaged, have the power tool

repaired before use.

Many accidents are caused by

poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to

be performed.

Use of the power tool for operations

different from those intended could result in a

hazardous situation.

Battery tool use and care

• Recharge only with the charger speciﬁed by the

manufacturer.

A charger that is suitable for one type

of battery pack may create a risk of ﬁre when used

with another battery pack.

• Use power tools only with speciﬁcally designated

battery packs.

Use of any other battery packs may

create a risk of injury and ﬁre.

• When a battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects,

that can make a connection from one terminal to

another.

Shorting the battery terminals together may

cause burns or a ﬁre.

• Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, ﬂush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritations

or burns.

Service

• Have your power tool serviced by a qualiﬁed

repair person using only identical replacement

parts.

This will ensure that the safety of the power tool

is maintained.

Hedge trimmer safety warnings -

Personal safety

• Keep all parts of the body away from the cutter

blade. Do not remove cut material or hold material

to be cut when blades are moving. Make sure the

switch is off when clearing jammed material.

A

moment of inattention while operating the hedge

trimmer may result in serious personal injury.

• Carry the hedge trimmer by the handle with the

cutter blade stopped. When transporting or

storing the hedge trimmer always ﬁt the cutting

device cover.

Proper handling of the hedge trimmer

will reduce possible personal injury from the cutter

blades.

• Hold the power tool by insulated gripping surface

only, because the cutter blade may contact hidden

wiring.

Cutter blades contacting a ”live” wire may

make exposed metal parts of the power tool ” live” and

could give the operator an electric shock.

IMPORTANT!

Always remove the battery before any maintenance on

the machine.

Children should be supervised to ensure that they do

not play with the appliance.

Store the machine out of reach of children. Never allow

children or other persons not trained in the use of the

machine and/or the battery to use or service it. Local

laws may regulate the age of the user.

Never use a machine that has been modiﬁed in any way

from its original speciﬁcation.

Wear personal protective equipment. See instructions

under the ”Personal protective equipment” heading.

The operator of the machine must ensure, while

working, that no persons or animals come closer than

15 metres.

Never use the machine in bad weather, for instance in

fog, in rain, strong winds, intense cold, etc. Extremely

hot weather may cause overheating of the machine.

Never use a machine that is faulty. Carry out the checks,

maintenance and service instructions described in this

manual. Some maintenance and service measures

must be carried out by trained and qualiﬁed specialists.

See instructions under the Maintenance heading.

Carry out an overall inspection of the machine before

use. See the maintenance schedule.

H1154526-38,136 LiHD50,_1 v2.fm Page 8 Friday, February 10, 2012 3:20 PM

GENERAL SAFETY PRECAUTIONS

English – 9

Personal protective equipment

HEARING PROTECTION

Wear hearing protection that provides adequate noise

reduction.

EYE PROTECTION

Always wear approved eye protection. If you use a visor

then you must also wear approved protective goggles.

Approved protective goggles must comply with the ANSI

Z87.1 standard in the USA or EN 166 in EU countries.

GLOVES

Gloves should be worn when necessary, e.g. when ﬁtting

cutting attachments.

BOOTS

Wear sturdy, non-slip boots or shoes.

CLOTHING

Wear clothes made of a strong fabric and avoid loose

clothing that can catch on twigs and branches. Always

wear heavy, long pants. Do not wear jewellery, shorts

sandals or go barefoot. Secure hair so it is above shoulder

level.

FIRST AID KIT

Always have a ﬁrst aid kit nearby.

Battery and battery charger

This section describes the battery and battery charger

safety for your battery product.

Only use Husqvarna original batteries for Husqvarna

products and only charge them in an original battery

charger from Husqvarna. The batteries are software

encrypted.

!

WARNING! This machine produces an

electromagnetic ﬁeld during operation.

This ﬁeld may under some

circumstances interfere with active or

passive medical implants. To reduce the

risk of serious or fatal injury, we

recommend persons with medical

implants to consult their physician and

the medical implant manufacturer before

operating this machine.

!

WARNING! Never allow children to use or

be in the vicinity of the machine. Since

the machine is easy to start, children

may be able to start it if they are not kept

under full surveillance. This can mean a

risk of serious personal injury. Therefore

disconnect the battery when the machine

is not under close supervision.

!

WARNING! Faulty blades can increase

the risk of accidents.

IMPORTANT!

Incorrect or careless use of a hedge trimmer can turn it

into a dangerous tool that can cause serious or even

fatal injury. It is extremely important that you read and

understand the contents of this operator's manual.

You must use approved personal protective equipment

whenever you use the machine. Personal protective

equipment cannot eliminate the risk of injury but it will

reduce the degree of injury if an accident does happen.

Ask your dealer for help in choosing the right equipment.

!

WARNING! Listen out for warning signals

or shouts when you are wearing hearing

protection. Always remove your hearing

protection as soon as the engine stops.

H1154526-38,136 LiHD50,_1 v2.fm Page 9 Friday, February 10, 2012 3:20 PM

GENERAL SAFETY PRECAUTIONS

10 – English

Battery safety

The rechargeable Husqvarna batteries, BLi, are

exclusively used as a power supply for the relevant

Husqvarna cordless appliances. To avoid injury, the

battery must not be used as a power source for other

devices.

• Use the battery in surroundings where temperatures

are between -10

°C and 40 °C.

• Do not expose the battery to microwaves or high

pressure.

• Never clean the battery or the battery charger with

water. See also instructions under the Maintenance

heading.

• Store the battery out of reach of children.

• Protect the battery from rain and wet conditions.

Battery charger safety

Only use Chargers, Husqvarna QC, for charging the

Husqvarna replacement batteries, BLi.

• Regularly check that the battery charger connection

wire is intact and that there are no cracks in it.

• Never carry the battery charger using the cable and

never pull out the plug by pulling the cable.

• Keep all cables and extension leads away from water,

oil and sharp edges. Make sure the cable is not

jammed in doors, fences or the like. Otherwise it can

cause the charger to become live.

Do not use:

• a faulty or damaged battery charger or never use a

faulty, damaged or deformed battery.

!

WARNING! Protect the battery from

direct sunlight, heat or open ﬂame. There

is a risk the battery may explode if it is

thrown into an open ﬁre. There is a risk of

burns and/or chemical burns.

!

WARNING! Avoid all skin contact with

battery acid. Battery acid may cause skin

irritation, burns or corrosive injuries. If

you get acid in your eyes, do not rub but

ﬂush your eyes with plenty of water for at

least 15 minutes. See a doctor. You must

wash any exposed skin with copious

amounts of water and soap in case of

incidental contact.

!

WARNING! Never connect the battery

terminal to keys, coins, screws or other

metal as this may short-circuit the

battery. Never insert objects into the

battery's air vents.

Unused batteries must be kept away from

metal objects such as nails, coins,

jewellery. Do not try to disassemble or

crush the battery

Li-ion

!

WARNING! Minimise the risk of electric

shock or short circuit as follows:

Never insert any object into the charger’s

cooling slots.

Do not try to dismantle the battery

charger.

Never connect the charger terminals to

metal objects as this can short circuit the

battery charger.

Use approved and intact wall sockets.

!

WARNING! Do not use the battery

charger close to corrosive or ﬂammable

materials. Do not cover the battery

charger. Pull out the plug to the battery

charger in the event of smoke or ﬁre.

Remember the risk of ﬁre.

Li-ion

H1154526-38,136 LiHD50,_1 v2.fm Page 10 Friday, February 10, 2012 3:20 PM

GENERAL SAFETY PRECAUTIONS

English – 11

Do not charge:

• non-rechargeable batteries in the battery charger or

use them in the machine.

• the battery charger to charge the battery outdoors.

• the battery in the rain or in wet conditions.

• the battery in direct sunlight.

Use the battery charger only when the surrounding

temperature is between 5

°C and 40 °C. Use the charger

in an environment which is well ventilated, dry and free

from dust.

Machine′s safety equipment

This section describes the machine′s safety equipment,

its purpose, and how checks and maintenance should be

carried out to ensure that it operates correctly. See the

”What is what?” section to locate where this equipment is

positioned on your machine.

The life span or the runtime of the machine can be

reduced and the risk of accidents can increase if machine

maintenance is not carried out correctly and if service

and/or repairs are not carried out professionally. If you

need further information please contact your nearest

service workshop.

Control panel

Make sure the machine is switched on or off when the

activate/deactivate button (1) is pressed and held (>1

sec.). The green LED (2) is lit or turned off.

Flashing warning symbol (3) and green LED (2) is lit could

indicate that:

• it is not possible to apply full power and, at the same

time, activate the machine. Release the power trigger

and the machine is active.

• the machine is blocked. Deactivate the machine.

Remove the battery from the machine. Remove the

twigs, branches or other materials that are jammed in

the blades.

• the machine is overloaded due to heavy trimming.

Release the power trigger and the machine is active.

If the warning symbol (3) ﬂashes, it indicates that the

machine is too hot and the machine deactivates. When

the machine is restored to normal temperature it is again

ready to run and you can activate the machine.

Solid red warning light (3) indicates service.

Power trigger lockout

The power trigger is designed to prevent accidental

operation. It is necessary to press both the power trigger

lockout and the power trigger. The order actuation power

trigger lockout and power trigger doesn’t matter. When

you release the handle, the power trigger and the power

trigger lockout both move back to their original positions.

This movement is operated by independent springs. This

arrangement means that the power trigger is

automatically locked at no operation state.

IMPORTANT!

All servicing and repair work on the machine requires

special training. This is especially true of the machine

′s

safety equipment. If your machine fails any of the

checks described below you must contact your service

agent. When you buy any of our products we guarantee

the availability of professional repairs and service. If the

retailer who sells your machine is not a servicing dealer,

ask him for the address of your nearest service agent.

!

WARNING! Never use a machine with

faulty safety equipment. The machine's

safety equipment must be checked and

maintained as described in this section.

If your machine fails any of these checks

contact your service agent to get it

repaired.

(2)

(1)

(3)

H1154526-38,136 LiHD50,_1 v2.fm Page 11 Friday, February 10, 2012 3:20 PM

GENERAL SAFETY PRECAUTIONS

12 – English

Turn on the machine. Press the power trigger lockout on

the front handle.

• Press the power trigger forward to release the power

trigger.

• Then press the power trigger up to apply full power.

Release the power trigger and check thereby the free

back movement of the power trigger. The cutting unit must

stop within 1 second.

Restart the machine and release the power trigger

lockout on the front handle. Check that the power trigger

lockout returns to its original position when you release it.

The cutting unit must stop within 1 second.

Hand guard

The hand guard prevents hands from coming into contact

with the moving blades, for example, if the operator loses

grip on the front handle.

Check that the hand guard is ﬁtted correctly. Check that

the hand guard is undamaged.

Blade and blade guard

The outer part of the blades (1) is shaped as blade

guards.

Check that the blade guard is not damaged or distorted.

Replace the cutting unit if it is bent or damaged.

1

2

Li-ion

H1154526-38,136 LiHD50,_1 v2.fm Page 12 Friday, February 10, 2012 3:20 PM

BATTERY HANDLING

English – 13

Battery

The display shows the battery capacity and if there are

any problems with the battery. The battery capacity is

displayed for 5 seconds after the machine is switched off

or the battery indicator button is pressed. The warning

symbol on the battery is lit when an error has occurred.

See fault codes.

Battery charger

Connect the battery charger

• Connect the battery charger to the voltage and

frequency speciﬁed on the rating plate. Put the

electric plug in the wall socket. The LED on the battery

charger ﬂashes green once.

• The battery will not be charged if the battery

temperature is over 50

°C. In that case the battery

charger will actively cool down the battery.

Connect the battery to the battery charger

Regularly check that the battery charger and the battery

are intact. See also instructions under the Maintenance

heading.

The battery must be charged before using it the ﬁrst time.

The battery is only 30% charged when delivered.

• Put the battery in the battery charger. Make sure that

the battery is connected to the battery charger.

• The green charging light is lit when the battery is

connected to the battery charger.

• When all LEDs are lit the battery is fully charged.

• Pull out the plug. Never jerk the power supply cable to

disconnect it from the wall socket.

• Remove the battery from the battery charger.

Charging status

Lithium-ion batteries can be charged whatever their

charge level. The charging process can be cancelled or

started whatever the battery's charge level. The battery is

not damaged. A fully charged battery will not lose its

charge even when the battery is left in the charger.

The battery will not be charged if the battery temperature

is over 50

°C.

LED lights Battery

All LEDs are lit Fully charged (75-100%).

LED 1, LED 2, LED 3 are

lit.

The battery is 50%-75%

charged.

LED 1, LED 2 are lit.

The battery is 25%-50%

charged.

LED 1 is lit.

The battery is 0%-25%

charged.

LED 1 ﬂashes

The battery is empty.

Charge the battery.

!

WARNING! Risk of electric shock and

short circuiting. Use approved and intact

wall sockets. Make sure that the cable is

not damaged. Replace cable if it appears

to be damaged in any way.

LED display Charging status

LED 1 ﬂashes

The battery is 0%-

25% charged.

LED 1 is lit, LED 2 ﬂashes.

The battery is 25%-

50% charged.

LED 1, LED 2 are lit, LED 3

ﬂashes

The battery is 50%-

75% charged.

LED 1, LED 2, LED 3 are lit,

LED 4 ﬂashes

Battery is 75%-100%

charged

LED 1, LED 2, LED 3, LED 4

are lit.

When all the LEDs

are lit on the battery,

it is fully charged.

H1154526-38,136 LiHD50,_1 v2.fm Page 13 Friday, February 10, 2012 3:20 PM

BATTERY HANDLING

14 – English

Transport and storage

• Secure the machine during transport.

• Always remove the battery for storage or transport.

• Store the battery and the battery charger in a dry,

moisture-free and frost-free space.

• To prevent accidents, ensure that your battery is not

connected to the machine when stored.

• Do not store the battery in places where static

electricity can occur. Never store the battery in a metal

box.

• Store the battery and the battery charger where the

temperature is between 5

°C and 45 °C and never in

direct sunlight.

• Store the battery charger only in an enclosed and dry

space.

• Be sure to store the battery separate from the battery

charger. Store the equipment in a lockable area so

that it is out of reach of children and unauthorized

persons.

• Ensure the machine is cleaned and that a complete

service is carried out before long-term storage.

Disposal of the battery, battery

charger and machine

Symbols on the product or its packaging indicate that this

product cannot be handled as domestic waste. It must

instead be submitted to an appropriate recycling station

for the recovery of electrical and electronic equipment.

By ensuring that this product is taken care of correctly,

you can help to counteract the potential negative impact

on the environment and people that can otherwise result

through the incorrect waste management of this product.

For more detailed information about recycling this

product, contact your municipality, your domestic waste

service or the shop from where you purchased the

product.

Li-ion

H1154526-38,136 LiHD50,_1 v2.fm Page 14 Friday, February 10, 2012 3:20 PM

STARTING AND STOPPING

English – 15

Check before starting

• Inspect the working area. Remove any objects that

could be thrown out.

• Check the cutting attachment. Never use blades that

are dull, cracked or damaged.

• Check that the machine is in perfect working order.

Check that all nuts and screws are tight.

• Only use the machine for the purpose it was intended

for.

• Make sure that the handle and safety features are in

good working order. Never use a machine that lacks a

part or has been modiﬁed outside its speciﬁcations.

Gloves should be worn when necessary.

• All covers must be correctly ﬁtted and undamaged

before you start the machine.

Connect battery to the machine

Make sure to use fully charged batteries. Use only a

Husqvarna original battery in your machine. See technical

data.

• Insert the battery in the machine. The battery should

slide easily into the battery holder on the machine. If

the battery does not slide in easily, it is not being

inserted correctly. The battery will lock itself into place

when you hear a click. Make sure the battery is ﬁtted

correctly to the machine.

Starting and stopping

Starting

Turn on the machine. Press and hold the start button (>1

sec.) until the green LED is lit.

Press the power trigger lockout up. It is placed on the front

handle.

Press the power trigger forward to release the power

trigger.

Then press the power trigger up to apply full power.

!

WARNING! Make sure no unauthorised

persons are in the working area.

Otherwise there is a risk of serious

personal injury. The safety distance is 15

metres.

Li-ion

1

2

H1154526-38,136 LiHD50,_1 v2.fm Page 15 Friday, February 10, 2012 3:20 PM

STARTING AND STOPPING

16 – English

Stopping

Stop the machine by releasing the power trigger or the

power trigger lockout and deactivate the machine.

Remove the battery from the machine by pressing the two

release buttons and pulling out the battery.

IMPORTANT! Always remove the battery to prevent the

machine being started by accident.

H1154526-38,136 LiHD50,_1 v2.fm Page 16 Friday, February 10, 2012 3:20 PM

WORKING TECHNIQUES

English – 17

General working instructions

Basic safety rules

• Never allow children to use or be in the vicinity of the

machine.

• Observe your surroundings and make sure that there

is no risk of people or animals coming into contact

with the cutting equipment.

• Never allow anyone else to use the machine without

ﬁrst ensuring that they have understood the contents

of the operator's manual.

• Inspect the working area. Remove any objects that

could be thrown out.

• Never work from a ladder, stool or any other raised

position that is not fully secured.

• CAUTION! Do not use the machine unless you are

able to call for help in the event of an accident. Ensure

that no-one comes closer than 15 metres while you

are working.

• Never use the machine in bad weather, for instance in

fog, in rain, strong winds, intense cold, etc.

• If any foreign object is hit or if vibrations occur stop the

machine immediately. Remove the battery from the

machine and check that the machine is not damaged.

SavE mode

The machine is equipped with a battery saving function

(SavE). Activate the function by pressing the SavE button.

A green LED will light to indicate that the function is on.

Automatic switch off functionality

The machine is equipped with a shutdown feature that

deactivates the machine if not used. The green LED and

the machine will switch off after 1 minute.

Safety instructions while working

• Do not overreach. Keep proper footing and balance at

all times.

• Turn off the machine when it has to be moved.

• Never put the machine down without turning it off ﬁrst

and always remove the battery.

IMPORTANT!

This section takes up the basic safety precautions for

working with a hedge trimmer.

If you encounter a situation where you are uncertain

how to proceed you should ask an expert. Contact your

dealer or your service workshop.

Avoid all usage which you consider to be beyond your

capability.

!

WARNING! The machine can cause

serious personal injury. Read the safety

instructions carefully. Learn how to use

the machine.

!

WARNING! Cutting tool. Do not touch the

tool without ﬁrst switching off the

engine. Always remove the battery

before any maintenance on the machine.

!

WARNING! Watch out for thrown objects.

Always wear approved eye protection.

Never lean over the cutting attachment

guard. Stones, rubbish, etc. can be

thrown up into the eyes causing

blindness or serious injury.

Keep unauthorised persons at a

distance. Children, animals, onlookers

and helpers should be kept outside the

safety zone of 15 metres. Stop the

machine immediately if anyone

approaches. Never swing the machine

around without ﬁrst checking behind you

to make sure no-one is within the safety

zone.

H1154526-38,136 LiHD50,_1 v2.fm Page 17 Friday, February 10, 2012 3:20 PM

WORKING TECHNIQUES

18 – English

• Always use both hands to hold the machine. Hold the

machine at the side of your body.

• Make sure that no clothes or parts of the body come

in contact with the cutting equipment when it is

activated.

• When the motor is switched off, keep your hands and

feet away from the cutting attachment until it has

stopped completely.

• Watch out for stumps of branches that can be thrown

out during cutting. Do not cut too close to the ground.

Stones and other objects can be thrown out.

• Check the working area for foreign objects such as

electricity cables, insects and animals, etc, or other

objects that could damage the cutting attachment,

such as metal items.

• If anything jams in the blades while you are working,

switch off the motor and wait until it has stopped

completely before cleaning the blades. Remove the

battery from the machine.

• Never leave the machine unsupervised with the motor

running.

Safety instructions after completing work

• The transport guard should always be ﬁtted to the

cutting attachment when the machine is not in use.

• Make sure the cutting attachment has stopped before

cleaning, carrying out repairs or an inspection.

Remove the battery from the machine.

• Always wear heavy-duty gloves when repairing the

cutting attachment. The blades are very sharp and

can easily cause cuts.

• Store the machine out of reach of children.

• Use only original spare parts for repairs.

Basic working techniques

• Work with a swinging action from the bottom upwards

when trimming sides.

• When trimming a hedge the engine should always

face away from the hedge.

• Hold the machine as close to your body as possible to

get the best balance.

• Make sure that the tip does not touch the ground.

• Do not rush the work, but work steadily until all the

branches have been cut back cleanly.

Li-ion

H1154526-38,136 LiHD50,_1 v2.fm Page 18 Friday, February 10, 2012 3:20 PM

MAINTENANCE

English – 19

Inspection and maintenance

All servicing and repair work on the machine requires

special training. This is especially true of the machine

′s

safety equipment. If your machine fails any of the checks

described below you must contact your service agent.

When you buy any of our products we guarantee the

availability of professional repairs and service. If the

retailer who sells your machine is not a servicing dealer,

ask him for the address of your nearest service agent.

Only use original spare parts.

Regularly check that the battery charger and the battery

are intact.

Cleaning

Clean the machine after use.

Make sure the battery and battery charger are clean and

that the terminals on the battery and the battery charger

are always clean and dry before the battery is placed in

the battery charger.

Keep the battery guide tracks clean. Clean plastic parts

with a clean and dry cloth.

Cleaning and lubrication

Clean any resin and plant residue from the blades using

cleaning agent before and after using the machine.

Check that the blade edges are not damaged or

deformed. File away any burrs. Check that the blades

move freely.

Lubricate the blade with special oil before long periods of

storage.

!

WARNING! Always remove the battery

before any maintenance on the machine.

IMPORTANT! Never clean the battery or the battery

charger with water.

Strong cleaning agents can damage the plastic.

Li-ion

H1154526-38,136 LiHD50,_1 v2.fm Page 19 Friday, February 10, 2012 3:20 PM

20 – English

MAINTENANCE

Troubleshooting schedule

Control panel

Troubleshooting takes place from the control panel.

Battery and battery charger

Troubleshooting the battery and/or the battery charger during charging.

LED display Possible faults Possible action

Error LED ﬂashes.

Overload.

The cutting attachment is

jammed. Release the cutting

attachment.

Temperature deviation.

Allow the machine to cool

down.

The power trigger and the

activate button are pressed

at the same time.

Release the power trigger

and the machine is active.

Error LED is lit with red light. Non repairable fault. Contact your service agent.

LED display Possible faults Possible action

Error LED ﬂashing.

Temperature

deviation.

Use the battery in surroundings

where temperatures are between -

10

°C and 40 °C.

Over voltage.

Check that the mains voltage

corresponds with that stated on the

rating plate on the machine.

Remove the battery from the battery

charger.

Error LED is lit.

Cell difference too

much (1V).

Contact your service agent.

H1154526-38,136 LiHD50,_1 v2.fm Page 20 Friday, February 10, 2012 3:20 PM

La pagina sta caricando ...

Husqvarna 136 LiHD50 Manuale del proprietario

Husqvarna 136 LiHD50 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti