Gardena AccuCut Li Manuale utente

Categoria
Tagliasiepi a motore
Tipo
Manuale utente

Questo manuale è adatto anche per

DE Betriebsanleitung
Strauchschere
EN Operation Instructions
Shrub Shear
FR Mode d’emploi
Taille-buisson
NL Gebruiksaanwijzing
Buxusschaar
SV Bruksanvisning
Häcksax
DA Brugsanvisning
Busktrimmer
FI Käyttöohje
Viimeistelyleikkuri
NO Bruksanvisning
Busktrimmer
IT Istruzioni per l’uso
Forbici rifilasiepi
ES Instrucciones de empleo
Tijeras recortasetos
PT Manual de instruções
Tesoura para arbustos
PL Instrukcja obsługi
Nóż do krzewów
HU Használati utasítás
Bokornyíró olló
CS Návod k obsluze
Nůžky na keře
AccuCut Li
Art. 9851-20
CS
HU PL PT
ES
IT NO FI DA
SV NL FR
EN DE
3
I1
1
2
I2
3
4
5
T1
9
0
q
2
we
O1
7
6
S1
8
1. SAFETY ...................................18
2. INSTALLATION ..............................24
3. OPERATION ................................25
4. MAINTENANCE .............................25
5. STORAGE .................................26
6. TROUBLESHOOTING .........................26
7. TECHNICAL DATA. . . . . . . . . . . . . . . . . . . . . . . . . . . .28
8. SERVICE / WARRANTY ........................29
Original instructions.
This product is not intended for use by persons
(including children) with reduced physical, sen-
sory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision
or instruction concerning use of the product by a person
responsible for their safety. Children should be supervised
to ensure that they do not play with the product. The use
of this product by young people under the age of 16 is not
recommended.
Intended use:
The GARDENA Shrub Shear is intended for cutting
indi vidual bushes, shrubs and climbing plants in private
domestic and hobby gardens.
DANGER! Risk of injury!
The product must not be used for cutting lawns / lawn
edges or for chopping up material for composting
purposes.
GARDENA Shrub Shear AccuCut Li
1. SAFETY
IMPORTANT!
Read the operator’s manual carefully before use and
keep for future reference.
If not used properly this product can be dangerous.
The warnings and safety instructions must be fol-
lowed to ensure reasonable safety and efficiency
in using this product. The operator is responsible
for following the warnings and instructions in this
manual and on the product. Never use the product
unless the guards provided by the manufacturer are
in the correct position.
Symbols on the product:
Read operator’s manual.
18
EN
DANGER!
Cutting tool continues to run after
switching off!
DANGER!
Keep bystanders away.
Do not let the product become wet with
rain or other moisture. Do not leave the
product outdoors while it is raining.
General Power Tool Safety Warnings
WARNING!
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result
in electric shock, fire and / or serious injury.
Save all warnings and instructions for future refer-
ence. The term “power tool” in the warnings refers to your
mains operated (corded) power tool or battery operated
(cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmos-
pheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adap-
tor plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk
of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the risk
of electric shock.
d) Do not abuse the cord. Never use the cord for car-
rying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk
of electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the risk
of electric shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply.
Use of an RCD reduces the risk of electric shock.
19
EN
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication.
A moment of inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment. Always wear
eye protection.
Protective equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and / or battery pack, picking up or carry-
ing the tool. Carrying power tools with your finger
on the switch or energising power tools that have the
switch on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key left attached to a rotating part of the
power tools may result in personal injury.
e) Do not overreach. Keep proper footing and bal-
ance at all times. This enables better control of the
power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts.
Loose clothes, jewellery or long hair can be caught in
moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used.
Use of dust collection can reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application.
The correct power tool will do the job better and safer at
the rate for which it was designed.
b) Do not use the power tool if the switch does not
turn it on and off.
Any power tool that cannot be controlled with the switch
is dangerous and must be repaired.
c) Disconnect the plug from the power source and /
or the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of chil-
drenand do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power
20
EN
tool’s operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
5) Battery tool use and care
a) Recharge only with the charger specified by the
manufacturer. A charger that is suit able for one type
of battery pack may create a risk of fire when used with
another battery pack.
b) Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
c) When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that
can make a connection from one terminal to
another. Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact acci-
dentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected
from the battery may cause irritation or burns.
6) Service
Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Hedge trimmer safety warnings:
Keep all parts of the body away from the cutter
blade. Do not remove cut material or hold mate rial
to be cut when blades are moving. Make sure the
switch is off when clearing jammed material.
A moment of inattention while operating the hedge
trimmer may result in serious personal injury.
Carry the hedge trimmer by the handle with the
cutter blade stopped. When transporting or
storing the hedge trimmer always fit the cutting
device cover.
Proper handling of the hedge trimmer will reduce
possible personal injury from the cutter blades.
Hold the power tool by insulated gripping sur faces
only, because the cutter blade may contact hid-
den wiring. Cutter blades contacting a “live” wire may
make exposed metal parts of the power tool “live”
and could give the operator an electric shock.
Additional safety warnings
DANGER! Small parts can be easily swallowed. There
is also a risk that the polybag can suffocate toddlers.
Keep toddlers away when you assemble the product.
21
EN
Work area safety
Only use the product in the manner and for the functions
described in these instructions.
The operator or user is responsible for accidents or
hazards occurring to other people or their property.
Do not use the product when a thunderstorm is
approaching.
Electrical safety
Before use, examine cable for damage, replace it if there
are signs of damage or ageing.
If the replacement of the supply cord is necessary, this
has to be done by the manufacturer or his agent in order
to avoid a safety hazard.
Do not use the product if the electric cables are damaged
or worn.
Immediately disconnect from the mains electricity supply
if the cable is cut, or the insulation is damaged. Do not
touch the electric cable until the electrical supply has been
disconnected.
Always disconnect the mains cable before disconnecting
any plug, cable connector or extension cable.
Always wind cable carefully, avoiding kinking.
Use only on AC mains supply voltage shown on the
product rating label.
Under no circumstances should an earth be connected to
any part of the product.
Warning! This product makes an electromagnetic field
while it operates. This field may under some conditions
interfere with active or passive medical implants. To
decrease the risk of con ditions that can possibly injure or
kill, we recommend persons with medical implants to
speak with their physician and the medical implant
manufacturer before operating.
DANGER! This product makes an electromagnetic field
while it operates. This field may under some conditions
interfere with active or passive medical implants. To
decrease the risk of conditions that can possibly injure or
kill, we recommend persons with medical implants to
speak with their physician and the medical implant manu-
facturer before you operate the product.
Cables
Use only permitted extension cables as per HD516.
v Ask your electrical specialist.
Personal safety
Always wear suitable clothing, protective gloves, and stout
shoes.
Thoroughly inspect the area where the product is to be
used and remove all wires and other foreign objects.
Before using the product and after any impact, check for
signs of wear or damage and repair as necessary.
If the product can no longer be switched off in the event
of a defect, place the product on a solid surface and moni-
tor until the battery is empty. Send the defective product
to the GARDENA Service Centre.
Never attempt to use an incomplete product or one with
an unauthorised modification.
22
EN
Power tool use and care
Know how to stop the product quickly in an emergency.
Never hold the product by the guard.
Do not use the product if the protection equipments
(protective cover, quick blade-stop) are damaged.
Do not use ladders whilst operating the product.
Remove the battery:
before leaving the product unattended for any period;
before clearing a blockage;
before checking, cleaning or working on the product;
if you hit an object. Do not use your product until you are
sure that the entire product is in a safe operating condi-
tion;
if the product starts to vibrate abnormally. Check
immedi ately. Excessive vibration can cause injury.
before passing to another person.
Only use the product between 0 – 40 °C.
Battery safety
FIRE RISK!
The battery to be charged must be placed on a non-flam-
mable, heat resistant and nonconductive surface while
charging.
Keep corrosive, flammable and easily combustible objects
clear of the battery charger and the battery.
Do not cover the battery charger and the battery while
charging.
Unplug the battery charger immediately in the event of
smoke formation or fire.
Only use the original GARDENA Battery Charger for
charging. The use of other battery chargers may damage
the batteries irreparably and even cause a fire.
RISK OF EXPLOSION!
v Protect product from heat and fire. Do not leave on
radiators or expose to strong sunshine for long periods.
Do not use the battery charger outdoors.
Protect the battery charger from damp or wet areas.
Only use the battery in an ambient temperature between
−10 °C and + 45 °C.
A non-functioning battery must be disposed of correctly.
It may not be sent via post. For further details, please con-
tact your local disposal com panies.
The battery charger should be checked regularly for signs
of damage or ageing (brittleness) and may only be used if
it is in perfect condition.
The charger unit provided may only be used to charge the
rechargeable batteries supplied with the product.
Non-rechargeable batteries must not be charged with this
battery charger (danger of fire).
The product must not be operated during charging.
After charging, disconnect the charger from the mains and
from the battery.
23
EN
Only charge battery between 10 – 45 °C.
After heavy duty service allow battery to cool down first.
Maintenance and storage
RISK OF INJURY!
Do not touch blades.
v When finishing or interrupting work push up
protection cover.
Keep all nuts, bolts and screws secure to be sure the
product is in safe working condition.
The product must not be stored over 35 °C or under
direct exposure to sunlight.
Do not store the unit in places with static electricity.
2. INSTALLATION
Initial Operation [ Fig. I1 ]:
DANGER! Risk of injury!
Cut injury when the product starts
accidentally.
v Before you initially operate the product, make
sure that the protective cover
1
is slid over the
blade
2
.
To charge the battery [ Fig. I2 ]:
The battery should be fully charged before using for the first
time. Charging time (see 7. TECHNICAL DATA).
The lithium-ion battery can be re-charged in any state of
charge, and the charging process can be interrupted at any
time without damaging the battery (no memory effect).
The product cannot be started during charging.
CAUTION!
Incorrect mains voltage damages batteries
and the battery charger.
v Ensure the correct mains voltage.
1. Connect charging cable
3
to the jack
4
of the Battery
Shear.
2. Connect battery charger
5
to an electrical socket.
During charging, the jack
4
flashes green.
The battery is charged.
When the jack
4
lights up green, the battery is fully
charged.
Check the charge status regularly while charging.
3. First pull the charging cable
3
out of the jack
4
and then
unplug the battery charger from the electrical socket.
When there is a sharp fall in the power of the battery, the
product switches off and the battery needs to be charged.
24
EN
3. OPERATION
To start the Shrub Shear [ Fig. O1 / I1 ]:
DANGER! Risk of injury!
Risk of injury if the product does not stop
when you release the start button.
v Do not bypass the safety devices or switches. For
example do not attach the starting lock-out
6
or
start button
7
to the handle.
To start:
The product is fitted with a starting lock-out
6
to prevent
the product from being turned on by accident.
1. Clear the area to be cut of stones and other solid
objects.
2. Remove the protective cover
1
from the blade
2
.
3. Push the starting lock-out
6
forwards and push the start
button
7
.
The product will start.
4. Release the starting lock-out
6
.
To stop:
1. Release the start button
7
.
2. Slide the protective cover
1
over the blade
2
.
4. MAINTENANCE
DANGER! Risk of injury!
Cut injury when the product starts
accidentally.
v Before you maintain the product, make sure that
the protective cover
1
is slid over the blade
2
[ Fig. I1 ].
To clean the Shrub Shear [ Fig. I1 ]:
DANGER! Electric shock!
Risk of injury and risk of damage to the
product.
v Do not clean the product with water or with
a water jet (in particular high-pressure water jet).
v Do not clean with chemicals including petrol or
solvents. Some can destroy critical plastic parts.
To increase operating time, the product should be cleaned
and sprayed after each use.
1. Clean the product with a damp cloth.
2. Lubricate the blade
2
with a low viscosity oil
(e. g. GARDENA spray-oil Art. 2366). Avoid contact
with the plastic parts.
25
EN
5. STORAGE
To put into storage [Fig. I1 ]:
The product must be stored away from children.
1. Charge the battery. This increases the life of the battery.
2. Clean the product (see 4. MAINTENANCE) and slide the
protective cover
1
over the blade
2
.
3. Stowe the product in a dry area where it has protection
from frost.
Disposal:
(in accordance with RL2012/19/EC)
The product must not be disposed of to normal
household waste. It must be disposed of in line
with local environmental regulations.
The GARDENA battery contains lithium-
ion cells that should not be disposed of
with normal household waste at the end
of its life.
Li-ion
IMPORTANT!
Dispose of the product through or via your municipal
recycling collection centre.
[ Fig. S1 ]:
1. Discharge lithium-ion cells
8
completely.
2. Remove lithium-ion cells
8
from the product.
3. Dispose of lithium-ion cells
8
properly.
6. TROUBLESHOOTING
DANGER! Risk of injury!
Cut injury when the product starts
accidentally.
v Before you troubleshoot the product, make
sure that the protective cover
1
is slid over
the blade
2
[ Fig. I1 ].
To change the blade [ Fig. T1 ]:
Only an original GARDENA blade is allowed to be
used. A new blade can be ordered by the GARDENA
Service.
1. Push the button
9
and slide the lid
0
downwards.
2. Remove the blade
2
.
26
EN
3. If necessary clean the transmission chamber and
lubricate the excentric drive
q
with some acid-free
grease (Vaseline).
4. Turn the excentric drive
q
downwards.
5. Pull the crank
w
on the back side of the blade
2
downwards.
6. Slide the ring
e
in the middle of the crank
w
.
7. Place the new blade
2
on the motor unit in such a way
that the excentric drive
q
is inserted in the ring
e
of the
crank
w
.
8. Slide the lid
0
upwards until it makes a click.
Problem Possible Cause Remedy
The jack flashes red
while charging
Allowed battery temperature
was exceeded.
v Let the battery cool down.
Restart the charging.
Runtime too low Blade soiled. v Clean and lubricate scissor blade
in accordance with the maintenance
instructions.
Product does not cut cleanly Blade blunt or damaged. v Change the blade
(see
To change the blade
).
NOTE:
For any other malfunctions please contact the GARDENA service department. Repairs must only be done by GARDENA
service departments or specialist dealers approved by GARDENA.
27
EN
Shrub Shear
Unit Value
AccuCut Li (Art. 9851)
Battery capacity Ah 2.15
Battery charging
time (80 % / 100 %)
(approx.)
hrs. 3.5 / 4.5
Battery charger
Mains voltage /
Mains frequency
V / Hz 100 – 240 / 50 – 60
Rated output
current
mA 500
Max. output voltage V (DC) 5.5
Length of blade cm 12
Weight (approx.) g 620
Sound pressure
level L
PA
1)
Uncertainty k
PA
dB (A)
66
2.5
Shrub Shear
Unit Value
AccuCut Li (Art. 9851)
Sound power
level L
WA
2)
measured / guaranteed
dB (A)
77 / 80
Hand / arm vibration
a
vhw
1)
Uncertainty k
a
m/s
2
< 2.5
1.5
Measuring process complying with:
1)
DIN EN 60745-2-15
2)
RL 2000/14/EC
NOTE: The stated vibration emission value has
been measured according to a standardized test
procedure and can be used for comparison of one
electric power tool with another. It can also be used for pre-
liminary evaluation of exposure. The vibration emission value
can vary during actual use of the electric power tool.
7. TECHNICAL DATA
28
EN
8. SERVICE / WARRANTY
Service:
Please contact the address on the back page.
Warranty:
In the event of a warranty claim, no charge is levied to you
for the services provided.
GARDENA Manufacturing GmbH offers a 2-year warranty
for this product (from the date of purchase) if the product
has been used exclusively for private purposes. This manu-
facturer’s warranty does not apply to used products pur-
chased from a secondary market. This warranty includes all
significant defects of the product that can be proved to be
material or manufacturing faults. This war ranty is fulfilled by
supplying a fully functional replacement product or by
repairing the faulty product sent to us free of charge; we
reserve the right to choose between these options. This
service is subject to the following provisions:
The product was used for its intended purpose as per the
recommendations in the operating instructions.
Neither the purchaser nor a third party has attempted to
repair the product.
Only original GARDENA spare and wear parts were used.
Normal wear and tear of parts and components, optical
changes, as well as wear parts and consumables, are
excluded from the warranty.
This manufacturer’s warranty does not affect warranty
entitlements against the dealer / retailer.
If problems arise with this product, please contactour
Service department. In the event of a warranty claim,
please send the defective product together with a copy of
the purchase receipt and a description of the defect,
sufficiently stamped, to the GARDENA service address on
the back page.
Consumables:
The blade and excentric drive are consumables and are not
included in the warranty.
29
EN
DE Produkthaftung
Wir weisen ausdrücklich darauf hin, dass wir in Übereinstimmung mit dem Produkthaftungsgesetz nicht für Schäden haften, die durch
unsere Produkte entstehen, wenn diese unsachgemäß und nicht durch einen von uns autorisierten Servicepartner repariert wurden oder
wenn keine Original GARDENA Teile oder von uns zugelassene Teile verwendet wurden.
EN Product liability
In accordance with the German Product Liability Act, we hereby expressly declare that we accept no liability for damage incurred from
our products where said products have not been properly repaired by a GARDENA-approved service partner or where original GARDENA
parts or parts authorised by GARDENA were not used.
FR Responsabilité
Conformément à la loi relative à la responsabilité du fait des produits défectueux, nous déclarons expressément par la présente que nous
déclinons toute responsabilité pour les dommages résultant de nos produits, si lesdits produits n‘ont pas été correctement réparés par
un partenaire d‘entretien agréé GARDENA ou si des pièces d’origine GARDENA ou des pièces agréées GARDENA n‘ont pas été utilisées.
NL Productaansprakelijkheid
Conform de Duitse wet inzake productaansprakelijkheid verklaren wij hierbij uitdrukkelijk dat wij geen aansprakelijkheid aanvaarden voor
schade ontstaan uit onze producten waarbij deze producten niet zijn gerepareerd door een GARDENA-erkende servicepartner of waarbij
geen originele GARDENA-onderdelen of onderdelen die door GARDENA zijn goedgekeurd zijn gebruikt.
SV Produktansvar
I enlighet med tyska produktansvarslagar förklarar vi härmed uttryckligen att vi inte åtar oss något ansvar för skador som orsakas av våra
produkter där produkterna inte har genomgått korrekt reparation från en GARDENA-godkänd servicepartner eller där originaldelar från
GARDENA eller delar godkända av GARDENA inte använts.
DA Produktansvar
I overensstemmelse med den tyske produktansvarslov erklærer vi hermed udtrykkeligt, at vi ikke påtager os noget ansvar for skader på
vores produkter, hvis de pågældende produkter ikke er blevet repareret korrekt af en GARDENA-godkendt servicepartner, eller hvor der
ikke er brugt originale GARDENA-reservedele eller godkendte reservedele fra GARDENA.
FI Tuotevastuu
Saksan tuotevastuulain mukaisesti emme ole vastuussa laitteiden vaurioista, jos korjauksia ei ole tehnyt GARDENAn hyväksymä huoltoliike
tai jos niiden syynä on muiden kuin alkuperäisten GARDENA-varaosien tai GARDENAn hyväksymien varaosien käyttö.
178
IT Responsabilità del prodotto
In conformità con la Legge tedesca sulla responsabilità del prodotto, con la presente dichiariamo espressamente che decliniamo qualsiasi
responsabilità per danni causati dai nostri prodotti qualora non siano stati correttamente riparati presso un partner di assistenza approvato
GARDENA o laddove non siano stati utilizzati ricambi originali o autorizzati GARDENA.
ES Responsabilidad sobre el producto
De acuerdo con la Ley de responsabilidad sobre productos alemana, por la presente declaramos expresamente que no aceptamos
ningún tipo de responsabilidad por los daños ocasionados por nuestros productos si dichos productos no han sido reparados por
un socio de mantenimiento aprobado por GARDENA o si no se han utilizado piezas originales GARDENA o piezas autorizadas por
GARDENA.
PT Responsabilidade pelo produto
De acordo com a lei alemã de responsabilidade pelo produto, declaramos que não nos responsabilizamos por danos causados pelos
nossos produtos, caso os tais produtos não tenham sido devidamente reparados por um parceiro de assistência GARDENA aprovado
ou se não tiverem sido utilizadas peças GARDENA originais ou peças autorizadas pela GARDENA.
PL Odpowiedzialność za produkt
Zgodnie z niemiecką ustawą o odpowiedzialności za produkt, niniejszym wyraźnie oświadczamy, że nie ponosimy żadnej odpowiedzial-
ności za szkody poniesione na skutek użytkowania naszych produktów, w przypadku gdy naprawa tych produktów nie była odpowiednio
przeprowadzana przez zatwierdzonego przez firmę GARDENA partnera serwisowego lub nie stosowano oryginalnych części GARDENA
albo części autoryzowanych przez tę firmę.
HU Termékszavatosság
A németországi termékszavatossági törvénnyel összhangban ezennel nyomatékosan kijelentjük, hogy nem vállalunk felelősséget a ter-
mékeinkben keletkezett olyan károkért, amelyek valamely GARDENA által jóváhagyott szervizpartner által nem megfelelően végzett javítás-
ból adódtak, vagy amely során nem eredeti GARDENA alkatrészeket vagy a GARDENA által jóváhagyott alkatrészeket használtak fel.
CS Odpovědnost za výrobek
V souladu s německým zákonem o odpovědnosti za výrobek tímto výslovně prohlašujeme, že nepřijímáme žádnou odpovědnost za
poškození vzniklá na našich výrobcích, kdy zmíněné výrobky nebyly řádně opraveny schváleným servisním partnerem GARDENA nebo
kdy nebyly použity originální náhradní díly GARDENA nebo náhradní díly autorizované společností GARDENA.
179
DE EU-Konformitätserklärung
Der Unterzeichner, GARDENA Germany AB, PO Box 7454, S-103 92 Stockholm, Schweden, bescheinigt hiermit, dass die nachstehend
aufgeführten Geräte bei Verlassen des Werks die harmonisierten EU-Leitlinien, EU-Normen für Sicherheit und besondere Normen erfüllen.
Dieses Zertifikat verliert seine Gültigkeit, wenn die Geräte ohne unsere Genehmigung verändert werden.
EN EC Declaration of Conformity
The undersigned, GARDENA Germany AB, PO Box 7454, S-103 92 Stockholm, Sweden, hereby certifies that, when leaving our factory,
the units indicated below are in accordance with the harmonised EU guidelines, EU standards of safety and product specific standards.
This certificate becomes void if the units are modified without our approval.
FR Déclaration de conformité CE
Le constructeur, soussigné : GARDENA Germany AB, PO Box 7454, S-103 92 Stockholm, Suède, déclare qu’à la sortie de ses usines le
matériel neuf désigné ci-dessous était conforme aux prescriptions des directives européennes énoncées ciaprès et conforme aux règles
de sécurité et autres règles qui lui sont applicables dans le cadre de l’Union européenne. Toute modification apportée à cet appareil sans
notre accord annule la validité de ce certificat.
NL EG-conformiteitsverklaring
De ondergetekende, GARDENA Germany AB, PO Box 7454, S-103 92 Stockholm, Zweden, verklaart hierbij dat de producten die hieron-
der staan vermeld, wanneerze onze fabriek verlaten, in overeenstemming zijn met de geharmoniseerde Europese richtlijnen, EU-normen
voor veiligheid en productspecifieke normen. Dit certificaat vervalt als de producten worden aangepast zonder onze toestemming.
SV EG-försäkran om överensstämmelse
Undertecknad firma GARDENA Germany AB, PO Box 7454, S-103 92 Stockholm, Sverige, intygar härmed att nedan nämnda produkter,
när de lämnar vår fabrik, överensstämmer med EU:s riktlinjer, EU:s säkerhetsstandarder och produktspeci fika standarder. Detta intyg skall
ogiltigförklaras om produkten ändras utan vårt godkännande.
DA EU-overensstemmelseserklæring
Undertegnede, GARDENA Germany AB, PO Box 7454, S-103 92 Stockholm, Sverige erklærer hermed, at nedenfor anførte enheder er
i overensstemmelse med de harmoniserede EUret ningslinjer, EU-standarder for sikkerhed og produktspecifikke standarder, når de forlader
fabrikken. Denne erklæring ugyldiggøres, hvis enhederne ændres uden vores godkendelse.
FI EY-vaatimustenmukaisuusvakuutus
GARDENA Germany AB, PO Box 7454, S-103 92 Stockholm, Ruotsi, vakuuttaa täten, että alla mainitut laitteet ovat tehtaalta lähtiessään
yhdenmukaistettujen EU-säännösten, EU:n turvastandardien ja tuotekohtaisten standardien mukaisia. Tämä vakuutus mitätöityy, jos lait-
teita muokataan ilman hyväksyntäämme.
180
IT Dichiarazione di conformità CE
La sottoscritta GARDENA Germany AB, PO Box 7454, S-103 92 Stockholm, Svezia, certifica che il prodotto qui di seguito indicato, nei
modelli da noi commercializzati, è conforme alle direttive armonizzate UE nonché agli standard di sicu rezza UE e agli standard specifici
di prodotto. Qualunque modifica apportata al prodotto senza nostra specifica autorizzazione invalida la presente dichiarazione.
ES Declaración de conformidad CE
El abajo firmante, GARDENA Germany AB, PO Box 7454, S-103 92 Stockholm, Suecia, certifica por la presente que, cuando salen de la
fábrica, las unidades indicadas a continuación cumplen las normas de armonización de la UE, las normas de la UE sobre seguridad y las
normas específicas del producto. Este certificado quedará sin efecto si se modifican las unidades sin nuestra autorización.
PT Declaração de conformidade CE
O abaixo-assinado, GARDENA Germany AB, PO Box 7454, S-103 92 Stockholm, Suécia, certifica por este meio que, ao sair da nossa
fábrica, as unidades indicadas acima estão em conformidade com as diretrizes uniformizadas da UE, os padrões de segurança da UE
e os padrões específicos do produto. Este certificado deixa de ser válido se as unidades forem modificadas sem a nossa aprovação.
PL Deklaracja zgodności WE
Niżej podpisany przedstawiciel firmy GARDENA Germany AB, PO Box 7454, S-103 92 Stockholm, Szwecja, niniejszym oświadcza, że
podane poniżej wyroby opuszczające fabrykę są zgodne ze zharmonizowanymi normami UE oraz z obowiązującymi w UE przepisami
bezpieczeństwa i normami dotyczącymi danego produktu. Modyfikacja wyrobów bez naszej zgody powoduje unieważnienie niniejszego
certyfikatu.
HU EK megfelelőségi nyilatkozat
Alulírott GARDENA Germany AB, PO Box 7454, S-103 92 Stockholm, Svédország ezzel tanúsítja, hogy az alábbiakban leírt egységek
a gyár elhagyásakor megfeleltek a harmonizált uniós előírásoknak és biztonsági és termékspecifikus szabványoknak. Ez a tanúsítvány
érvényét veszti, ha az egységeket jóváhagyásunk nélkül átalakítják.
CS Prohlášení o shodě ES
Níže uvedená společnost GARDENA Germany AB, PO Box 7454, S-103 92 Stockholm, Švédsko, tímto potvrzuje, že při opuštění
naší továrny jsou jednotky uvedené níže v souladu s harmonizovanými pokyny EU, standardy EU ohledně bezpečnosti a specifickými
produktovými standardy. Tento certifikát pozbývá platnosti, pokud dojde k úpravě jednotek bez našeho schválení.
181
Produktbezeichnung:
Description of the product:
Désignation du produit :
Beschrijving van het product:
Beskrivning av produkten:
Beskrivelse af produktet:
Tuotteen kuvaus:
Descrizione del prodotto:
Descripción del producto:
Descrição do produto:
Opis produktu:
A termék leírása:
Popis výrobku:
Strauchschere
Shrub Shear
Taille-buisson
Buxusschaar
Häcksax
Busktrimmer
Viimeistelyleikkuri
Forbici rifilasiepi
Tijeras recortasetos
Tesoura para arbustos
Nóż do krzewów
Bokornyíró olló
Nůžky na keře
Schall-Leistungspegel: gemessen / garantiert
Noise level: measured / guaranteed
Puissance acoustique : mesurée / garantie
Geluidsniveau: gemeten / gegarandeerd
Ljudnivå: uppmätt / garanterad
Lydtryksniveau: afmålt / garanti
Melun tehotaso: mitattu / taattu
Livello rumorosità: testato / garantito
Nivel sonoro: medido / garantizado
Nível de ruido: medido / garantido
Poziom natężenia dźwięku: zmierzone / gwarantowane
Zajteljesítmény szint: mért / garantált
Hluková hladina výkonu: naměřeno / garantováno
77 dB (A) / 80 dB (A)
Produkttyp:
Product type:
Type de produit :
Producttype:
Produkttyp:
Produkttype:
Tuotetyyppi:
Tipo di prodotto:
Tipo de producto:
Tipo de produto:
Typ produktu:
Terméktípus:
Druh výrobku:
AccuCut Li
Artikelnummer:
Article number:
Référence :
Artikelnummer:
Artikelnummer:
Artikelnummer:
Tuotenumero:
Codice articolo:
Referencia:
Número de referência:
Numer katalogowy:
Cikkszámok:
Objednací číslo:
9851
EU-Richtlinien:
EC-Directives:
Directives CE :
EG-richtlijnen:
EU-direktiv:
EF-direktiver:
EY-direktiivit:
Direttive UE:
Directiva CE:
Diretivas CE:
Dyrektywy WE:
EK-irányelvek:
Předpisy ES:
2006/42/EG
2014/30/EG
2011/65/EG
2000/14/EG
Ladegerät / Battery charger:
2014/35/EG
182
Harmonisierte EN-Normen / Harmonised EN:
Anbringungsjahr der CE-Kennzeichnung:
Year of CE marking:
Année d’apposition du marquage CE :
Installatiejaar van de CE-aanduiding:
Märkningsår:
CE-Mærkningsår:
CE-merkin kiinnitysvuosi:
Anno di applicazione della certificazione CE:
Colocación del distintivo CE:
Ano de marcação pela CE:
Rok nadania oznakowania CE:
CE-jelzés elhelyezésének éve:
Rok umístění značky CE:
2015
Hinterlegte Dokumentation:
GARDENA
Technische Dokumentation,
M. Kugler, 89079 Ulm
Deposited Documentation:
GARDENA
Technical Documentation,
M. Kugler, 89079 Ulm
Documentation déposée:
Documentation technique
GARDENA,
M. Kugler, 89079 Ulm
Konformitätsbewertungs-
verfahren:
Nach 2000/14/EG
Art. 14 Anhang V
Conformity Assessment
according to:
2000/14/EC Procedure:
art. 14 Annex V
Procédure d’évaluation
de la conformité:
Selon 2000 /14 /CE
art. 14 Annexe V
Ulm, den 15.05.2017
Ulm, 15.05.2017
Fait à Ulm, le 15.05.2017
Ulm, 15-05-2017
Ulm, 2017.05.15.
Ulm, 15.05.2017
Ulmissa, 15.05.2017
Ulm, 15.05.2017
Ulm, 15.05.2017
Ulm, 15.05.2017
Ulm, dnia 15.05.2017
Ulm, 15.05.2017
Ulm, 15.05.2017
Der Bevollmächtigte
Authorized representative:
Le mandataire
De gevolmachtigde
Auktoriserad representant
Autoriseret repræsentant
Valtuutettu edustaja
Persona delegata
La persona autorizada
O representante
Pełnomocnik
Meghatalmazott
Zplnomocněnec
Reinhard Pompe
Vice President
EN ISO 12100
EN 60745-1
EN 60745-2-15
Ladegerät / Battery charger:
EN 60335-1
EN 60335-2-29
Batterie / Battery:
IEC 62133
183
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22

Gardena AccuCut Li Manuale utente

Categoria
Tagliasiepi a motore
Tipo
Manuale utente
Questo manuale è adatto anche per

in altre lingue