Husqvarna 115IHD45 Manuale del proprietario

115iHD45

GB

Oper

ator’

s man

ual 4-20

SE

Br

uksan

visning 21-37

DK

Br

ugsan

visning 38-54

NO

Br

uksan

visning 55-71

FI

Käyttöohje 72-88

DE

Bedien

ungsanw

eisung 89-106

FR

Man

uel d’utilisation 107-125

NL

Gebr

uiksaanwijzing 126-142

IT

Istr

uzioni per l’uso 143-159

ES

Man

ual de instr

ucciones 160-177

PT

Instr

uções par

a o uso 178-195

I

1

2

3

4

7

10

5

6

8

9

11 12

14

15

13

16

2

1

CLICK!

1

6

7

3

4

5

8

15

17

16

2

3

9

1

2

3

1

18

11

12

10

19

13

15

14

19

22

18

21

24

17

20

23

25

27

26

(A)

(B)

1

2

3

1

2

3

KEY

T

O SYMBOLS

4

–

English

Symbols on the mac

hine:

T

ranslation of the original Swedish operating instruction.

WARNING! Incorrect or careless use of

a hedge trimmer can turn it into a

dangerous tool that can cause serious

or even fatal injury. It is extremely

important that you read and

understand the contents of this

operator's manual.

Please read the operator’s manual

carefully and make sure you understand

the instructions before using the

machine.

Always wear:

• Approved hearing protection

• Approved eye protection

Always wear approved protective

gloves.

Wear sturdy, non-slip boots.

This product is in accordance with

applicable EC directives.

Symbols on the product or its packaging

indicate that this product cannot be

handled as domestic waste. This product

must be deposited at an appropriate

recycling facility. (Applies to Europe only)

Do not expose to rain.

Direct current.

Noise emission to the environment

according to the European

Community’s Directive. The machine’s

emission is speciﬁed in the Technical

data chapter and on the label.

The rating plate showing serial

number.

yyyy

is the production

year,

ww

is the

productionweek.

Symbols on the batter

y and/or on

the battery charger:

Please read the oper

ator’s

manual carefully and make sure

you understand the instructions

before using the machine.

This product must be deposited

at an appropriate recycling

facility. (Applies to Europe only)

Fail-safe transformer

Use and store battery charger only

indoors.

Double insulation

Other symbols/decals on the mac

hine refer to special

certiﬁcation requirements for certain markets.

yyyywwxxxxx

CONTENTS

English

–

5

Contents

Note the f

ollowing before

starting:

Please read the oper

ator's manual carefully.

KEY

TO SYMBOLS

Symbols on the machine:

..................................... 4

Symbols on the battery and/or on the battery

charger: ................................................................

4

CONTENTS

Contents

............................................................... 5

Note the following before starting: ........................ 5

INTR

ODUCTION

Dear Customer

, .................................................... 6

What is what? ....................................................... 6

GENERAL SAFETY PRECA

UTIONS

Gener

al power tool safety warnings ..................... 7

Personal protective equipment ............................. 9

Machine

′

s safety equipment ................................. 9

Battery and battery charger .................................. 10

B

ATTERY HANDLING

Batter

y .................................................................. 12

Battery charger ..................................................... 12

Transport and storage .......................................... 12

Disposal of the battery, battery charger and

machine ................................................................

12

ST

ARTING AND STOPPING

Chec

k before starting ........................................... 13

Connect battery to the machine ........................... 13

Starting and stopping ........................................... 13

W

ORKING TECHNIQUES

Gener

al working instructions ................................ 14

MAINTENANCE

Inspection and maintenance

................................ 16

Cleaning and lubrication ....................................... 16

Troubleshooting schedule ..................................... 17

Maintenance schedule ......................................... 18

TECHNICAL D

ATA

T

echnical data ...................................................... 19

EC Declaration of Conformity ............................... 20

!

W

ARNING! Long-term exposure to noise

can result in permanent hearing

impairment. So always use approved

hearing protection.

!

W

ARNING! Under no circumstances may

the design of the machine be modiﬁed

without the permission of the

manufacturer. Always use original

accessories. Non-authorized

modiﬁcations and/or accessories can

result in serious personal injury or the

death of the operator or others.

!

W

ARNING! Incorrect or careless use of a

hedge trimmer can turn it into a

dangerous tool that can cause serious or

even fatal injury. It is extremely important

that you read and understand the

contents of this operator's manual.

INTR

ODUCTION

6

–

English

Dear Customer

,

Cong

ratulations on your choice to buy a Husqvarna

product! Husqvarna is based on a tradition that dates

back to 1689, when the Swedish King Karl XI ordered the

construction of a factory on the banks of the Husqvarna

River, for production of muskets. The location was logical,

since water power was harnessed from the Huskvarna

River to create the water-powered plant. During the more

than 300 years in existence, the Husqvarna factory has

produced a lot of different products, from wood stoves to

modern kitchen appliances, sewing machines, bicycles,

motorcycles etc. In 1956, the ﬁrst motor driven lawn

mowers appeared, followed by chain saws in 1959, and it

is within this area Husqvarna is working today.

Today Husqvarna is one of the leading manufacturers in

the world of forest and garden products, with quality as

our highest priority. The business concept is to develop,

manufacture and market motor-driven products for

forestry and gardening, as well as for the building and

construction industry. Husqvarna

′

s aim is also to be at the

front edge for ergonomics, usability, security and

environmental protection. That is the reason why we have

developed many different features to add to our products

within these areas.

We are convinced that you will appreciate with great

satisfaction the quality and performance of our product for

a very long time to come. The purchase of one of our

products gives you access to professional help with

repairs and service whenever this may be necessary. If

the retailer who sells your machine is not one of our

authorized dealers, ask for the address of your nearest

service workshop.

It is our wish that you will be satisﬁed with your product

and that it will be your companion for a long time. Think of

this operator

′

s manual as a valuable document. By

following its content (usage, service, maintenance, etc),

the life span and the second-hand value of the machine

can be extended. If you sell this machine, make sure that

the operator

′

s manual is passed on to the buyer.

Thank you for using a Husqvarna product.

Husqvarna AB has a policy of continuous product

development and therefore reserves the right to modify

the design and appearance of products without prior

notice.

What is what?

(1)

1

Operator

′

s manual

2 Rear handle

3 Power trigger on front handle

4 Front handle

5 Cutter

6 Transport guard

7 Power trigger on rear handle

8 Control panel

9 Hand guard

10 Battery

11 Battery charger

12 Cord

13 Battery indicator button

14 Battery status

15 Warning indicator

16 SavE button

17 Activate and deactivate button

18 Power on and warning indicator

19 Battery release buttons

GENERAL SAFETY PRECA

UTIONS

English

–

7

General po

wer tool safety

warnings

Please read the oper

ator’s manual carefully and make

sure you understand the instructions before using the

machine.

(Figure 1) - (Figure 27) refer to ﬁgures on pages 2-3.

The machine is only designed for cutting branches and

twigs.

W

ork area safety

•

Keep work area clean and well lit.

Cluttered or dark

areas invite accidents.

•

Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂammable liquids, gases or dust.

Power tools

create sparks which may ignite the dust or fumes.

•

Keep children and bystanders away while

operating a power tool.

Distractions can cause you

to lose control.

Electrical saf

ety

•

Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools.

Unmodiﬁed plugs and matching outlets will

reduce the risk of electric shock.

• Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators.

There is an increased risk of electric

shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet

conditions.

Water entering a power tool will increase

the risk of electric shock.

• Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts.

Damaged or entangled cords increase

the risk of electric shock.

• When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of

electric shock.

• If operating a power tool in a damp location is

unaviodable, use a residual current device (RCD)

protected supply.

Use of an RCD reduces the risk of

electric shock.

Personal safety

• Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the inﬂuence of drugs, alcohol or medication.

A

moment of inattention while operating power tools

may result in serious personal injury.

• Use personal protective equipment. Always wear

eye protection.

Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personal injuries.

• Prevent unintentional starting. Ensure the switch

is in the OFF-position before connecting to a

power source and/or battery pack, picking up or

carrying the tool.

Carrying power tools with your

ﬁnger on the switch or energising power tools that

have the switch on invites accidents.

• Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left

attached to a rotating part of the power tool may result

in personal injury.

• Do not overreach. Keep proper footing and

balance at all times.

This enables better control of

the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts.

Loose clothes, jewellery or

long hair can be caught in moving parts.

• If devices are provided for the connection of dust

extraction and collection facilities, ensure these

are connected and properly used.

Use of dust

collection can reduce dust-related hazards.

Power tool use and care

• Do not force the power tool. Use the correct power

tool for your application.

The correct power tool will

do the job better and safer at the rate for which it was

designed.

• Do not use the power tool if the switch does not

turn it on and off.

Any power tool that cannot be

controlled with the switch is dangerous and must be

repaired.

• Disconnect the plug from the power source and/or

the battery pack from the power tool before

making any adjustments, changing accessories,

or storing power tools.

Such preventive safety

measures reduce the risk of starting the power tool

accidentally.

• Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands

of untrained users.

!

WARNING! Read all safety warnings and

all instructions. Failure to follow the

warnings and instructions may result in

electric shock, ﬁre and/or serious injury.

IMPORTANT!

Save all warnings and instructions for future reference.

The term ”power tool” in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

GENERAL SAFETY PRECAUTIONS

8 – English

• Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and

any other condition that may affect the power

tool´s operation. If damaged, have the power tool

repaired before use.

Many accidents are caused by

poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to

be performed. Use of the power tool for operations

different from those intended could result in a

hazardous situation.

Battery tool use and care

• Recharge only with the charger speciﬁed by the

manufacturer.

A charger that is suitable for one type

of battery pack may create a risk of ﬁre when used

with another battery pack.

• Use power tools only with speciﬁcally designated

battery packs.

Use of any other battery packs may

create a risk of injury and ﬁre.

• When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys,

nails, screws or other small metal objects, that

can make a connection from one terminal to

another.

Shorting the battery terminals together may

cause burns or a ﬁre.

• Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, ﬂush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritations

or burns.

Hedge trimmer safety warnings -

Personal safety

• Use both hands when operating the hedgetrimmer.

Using one hand could cause loss of control and result

in serious personal injury.

• Keep all parts of the body away from the cutter

blade. Do not remove cut material or hold material

to be cut when blades are moving. Make sure the

switch is off when clearing jammed material.

Blades coast after turn off.

A moment of inattention

while operating the hedge trimmer may result in

serious personal injury.

• Carry the hedge trimmer by the handle with the

cutter blade stopped. When transporting or

storing the hedgetrimmer always ﬁt the cutting

device cover.

Proper handling of the hedge trimmer

will reduce possible personal injury from the cutter

blades.

• Hold the power tool by insulated gripping surface

only, because the cutter blade may contact hidden

wiring. Cutter blades contacting a ”live” wire may

make exposed metal parts of the power tool ” live” and

could give the operator an electric shock.

• DANGER -Keep hands away from blade. Contact

with blade will result in serious personal injury.

• Check the hedge for foreign objects, e. g. wire fences.

IMPORTANT!

Always remove the battery before any maintenance on

the machine.

Children should be supervised to ensure that they do

not play with the appliance.

Store the machine out of reach of children. Never allow

children or other persons not trained in the use of the

machine and/or the battery to use or service it. Local

laws may regulate the age of the user.

Never use a machine that has been modiﬁed in any way

from its original speciﬁcation.

Wear personal protective equipment. See instructions

under the ”Personal protective equipment” heading.

The operator of the machine must ensure, while

working, that no persons or animals come closer than

15 meters.

Never use the machine in bad weather, for instance in

fog, in rain, strong winds, intense cold, etc. Extremely

hot weather may cause overheating of the machine.

Never use a machine that is faulty. Carry out the safety

checks, maintenance and service instructions

described in this manual. Some maintenance and

service measures must be carried out by trained and

qualiﬁed specialists. See instructions under the

Maintenance heading.

Carry out an overall inspection of the machine before

use. See the maintenance schedule.

Have your power tool serviced by a qualiﬁed repair

person using only identical replacement parts.

This

will ensure that the safety of the power tool is

maintained.

!

WARNING! This machine produces an

electromagnetic ﬁeld during operation.

This ﬁeld may under some

circumstances interfere with active or

passive medical implants. To reduce the

risk of serious or fatal injury, we

recommend persons with medical

implants to consult their physician and

the medical implant manufacturer before

operating this machine.

GENERAL SAFETY PRECAUTIONS

English – 9

Personal protective equipment

Always wear:

• Wear hearing protection that provides adequate noise

reduction.

• Always wear approved eye protection. If you use a

visor then you must also wear approved protective

goggles. Approved protective goggles must comply

with the ANSI Z87.1 standard in the USA or EN 166 in

EU countries.

• Gloves should be worn when necessary, e.g. when

ﬁtting cutting attachments.

• Wear sturdy, non-slip boots or shoes.

• Wear clothes made of a strong fabric and avoid loose

clothing that can catch on twigs and branches. Always

wear heavy, long pants. Do not wear jewellery, shorts

sandals or go barefoot. Secure hair so it is above

shoulder level.

• Always have a ﬁrst aid kit nearby.

Machine′s safety equipment

This section describes the machine′s safety equipment,

its purpose, and how checks and maintenance should be

carried out to ensure that it operates correctly. See the

”What is what?” section to locate where this equipment is

positioned on your machine.

The life span or the runtime of the machine can be

reduced and the risk of accidents can increase if machine

maintenance is not carried out correctly and if service

and/or repairs are not carried out professionally. If you

need further information please contact your nearest

service workshop.

Control panel

Make sure the machine is switched on or off when the

activate/deactivate button (1) is pressed and held (>1

sec.). The green LED (2) is lit or turned off.

(Figure 5)

Flashing warning indicator (3) and green LED (2) is lit

could indicate that:

• it is not possible to apply full power and, at the same

time, activate the machine. Release the power trigger

and the machine is active.

• the machine is blocked. Deactivate the machine.

Remove the battery from the machine. Remove the

twigs, branches or other materials that are jammed in

the blades.

• the machine is overloaded due to heavy trimming.

Release the power trigger and the machine is active.

If the warning symbol (3) ﬂashes, it indicates that the

machine is too hot and the machine deactivates. When

the machine is restored to normal temperature it is again

ready to run and you can activate the machine.

Solid red warning light (3) indicates service.

Power trigger on front handle

The power trigger on front handle is designed to prevent

accidental operation. It is necessary to press both the

power trigger on the front handle and the power trigger on

the rear handle. The order actuation power trigger front

handle and power trigger on the rear handle doesn’t

matter. When you release the handle, the power trigger on

the rear handle and the power trigger on the front handle

both move back to their original positions. This movement

is operated by independent springs. This arrangement

!

WARNING! Never allow children to use or

be in the vicinity of the machine. Since

the machine is easy to start, children

may be able to start it if they are not kept

under full surveillance. This can mean a

risk of serious personal injury. Therefore

disconnect the battery when the machine

is not under close supervision.

!

WARNING! Faulty blades can increase

the risk of accidents.

IMPORTANT!

Incorrect or careless use of a hedge trimmer can turn it

into a dangerous tool that can cause serious or even

fatal injury. It is extremely important that you read and

understand the contents of this operator's manual.

You must use approved personal protective equipment

whenever you use the machine. Personal protective

equipment cannot eliminate the risk of injury but it will

reduce the degree of injury if an accident does happen.

Ask your dealer for help in choosing the right equipment.

!

WARNING! Listen out for warning signals

or shouts when you are wearing hearing

protection. Always remove your hearing

protection as soon as the motor stops.

IMPORTANT!

All servicing and repair work on the machine requires

special training. This is especially true of the machine

′s

safety equipment. If your machine fails any of the

checks described below you must contact your service

agent. When you buy any of our products we guarantee

the availability of professional repairs and service. If the

retailer who sells your machine is not a servicing dealer,

ask him for the address of your nearest service agent.

!

WARNING! Never use a machine with

faulty safety equipment. The machine's

safety equipment must be checked and

maintained as described in this section.

If your machine fails any of these checks

contact your service agent to get it

repaired.

GENERAL SAFETY PRECAUTIONS

10 – English

means that the power trigger on the rear handle is

automatically locked at no operation state.

Turn on the machine. Press the power trigger on the front

handle.

(Figure 6)

Then press the power trigger on the rear handle up to

apply full power.

(Figure 7)

Release the power trigger on the rear handle and check

thereby the free back movement of the power trigger. The

cutting unit must stop within 1 second.

Restart the machine and release the power trigger on the

front handle on the front handle. Check that the power

trigger lockout returns to its original position when you

release it. The cutting unit must stop within 1 second.

Hand guard

The hand guard prevents hands from coming into contact

with the moving blades, for example, if the operator loses

grip on the front handle.

(Figure 9)

Check that the hand guard is ﬁtted correctly. Check that

the hand guard is undamaged.

Blade and blade guard

The outer part of the blades (1) is shaped as blade

guards.

(Figure 9)

Check that the blade guard is not damaged or distorted.

Replace the cutting unit if it is bent or damaged.

Battery and battery charger

This section describes the battery and battery charger

safety for your battery product.

Only use Husqvarna original batteries for Husqvarna

products and only charge them in an original battery QC

charger from Husqvarna. The batteries are software

encrypted.

Use only a Husqvarna original BLi battery in your

machine.

Battery safety

The rechargeable Husqvarna batteries, BLi, are

exclusively used as a power supply for the relevant

Husqvarna cordless appliances. To avoid injury, the

battery must not be used as a power source for other

devices.

(Figure 2)

• Use the battery in surroundings where temperatures

are between -10

°C and 40 °C.

• Do not expose the battery to microwaves or high

pressure.

• Never clean the battery or the battery charger with

water. See instructions under the Maintenance

heading.

• Store the battery out of reach of children.

• Protect the battery from rain and wet conditions.

• Do not open or mutilate the battery(ies). Released

electrolyte is corrosive and may cause damage to the

eyes or skin. It may be toxic if swallowed.

Battery charger safety

Only use Chargers, Husqvarna QC, for charging the

Husqvarna replacement batteries, BLi.

(Figure 3)

!

WARNING! Protect the battery from

direct sunlight, heat or open ﬂame. There

is a risk the battery may explode if it is

thrown into an open ﬁre. There is a risk of

burns and/or chemical burns.

!

WARNING! Avoid all skin contact with

battery acid. Battery acid may cause skin

irritation, burns or corrosive injuries. If

you get acid in your eyes, do not rub but

ﬂush your eyes with plenty of water for at

least 15 minutes. See a doctor. You must

wash any exposed skin with copious

amounts of water and soap in case of

incidental contact.

!

WARNING! Never connect the battery

terminals to keys, coins, screws or other

metal as this may short-circuit the

battery. Never insert objects into the

battery's air vents.

Unused batteries must be kept away from

metal objects such as nails, coins,

jewellery. Do not try to disassemble or

crush the battery

!

WARNING! Minimise the risk of electric

shock or short circuit as follows:

Never insert any object into the charger’s

cooling slots.

Do not try to dismantle the battery

charger.

Never connect the charger terminals to

metal objects as this can short circuit the

battery charger.

Use approved and intact wall sockets.

GENERAL SAFETY PRECAUTIONS

English – 11

• Regularly check that the battery charger connection

wire is intact and that there are no cracks in it.

• Never carry the battery charger using the cord and

never pull out the plug by pulling the cord.

• Keep all cables and extension leads away from water,

oil and sharp edges. Make sure the cable is not

jammed in doors, fences or the like. Otherwise it can

cause the charger to become live. Inspect extensions

cords periodically and replace if damaged.

Do not use:

• a faulty or damaged battery charger or never use a

faulty, damaged or deformed battery.

(Figure 4)

Do not charge:

• non-rechargeable batteries in the battery charger or

use them in the machine.

• the battery in the battery charger outdoors.

• the battery in the rain or in wet conditions.

• the battery in direct sunlight.

Use the battery charger only when the surrounding

temperature is between 5

°C and 40 °C. Use the charger

in an environment which is well ventilated, dry and free

from dust.

!

WARNING! Do not use the battery

charger close to corrosive or ﬂammable

materials. Do not cover the battery

charger. Pull out the plug to the battery

charger in the event of smoke or ﬁre.

Remember the risk of ﬁre.

BATTERY HANDLING

12 – English

Battery

The display shows the battery capacity and if there are

any problems with the battery. The battery capacity is

displayed for 5 seconds after the machine is switched off

or the battery indicator button (1) is pressed. The warning

symbol on the battery is lit when an error has occurred

(2). See fault codes.

(Figure 27)

Battery charger

Connect the battery charger

• Connect the battery charger to the voltage and

frequency speciﬁed on the rating plate.

• The battery will not be charged if the battery

temperature is over 50

°C.

Connect the battery to the battery

charger.

Regularly check that the battery charger and the battery

are intact. See instructions under the Maintenance

heading.

The battery must be charged before using it the ﬁrst time.

The battery is only 30% charged when delivered.

• Connect the battery to the battery charger. (Figure

11)

• The green charging light on the charger is lit when the

battery is connected to the battery charger. The

charging process is ongoing.

(Figure 10)

• When all the LEDs are lit on the battery, it is fully

charged.

(Figure 12)

• Pull out the plug. Never jerk the power supply cable to

disconnect it from the wall socket.

• Disconnect the charger from the battery.

Charging status

Lithium-ion batteries can be charged at whatever

charging level. The charging process can be cancelled or

started whatever the battery’s charge level is. A fully

charged battery will not lose its charge even when the

battery is left in the charger.

Transport and storage

• The contained lithium-ion batteries are subject to the

Dangerous Goods Legislation requirements.

• For commercial transports e.g. by third parties,

forwarding agents, special requirement on packing

and labeling must be observed.

• For preparation of the item being shipped, consulting

an expert for hazardous material is required. Please

also observe possibly more detailed national

regulations.

• Tape or mask off open contacts and pack up the

batteriy in such a manner that it cannot move around

in the packing.

• Always remove the battery for storage or transport.

• Store the battery and the battery charger in a dry,

moisture-free and frost-free space.

• Do not store the battery in places where static

electricity can occur. Never store the battery in a metal

box.

• Store the battery where the temperature is between 5

°C and 25 °C and never in direct sunlight.

• Store the battery charger where the temperature is

between 5

°C and 45 °C and never in direct sunlight.

• Store the battery charger only in an enclosed and dry

space.

• Be sure to store the battery separate from the battery

charger. Store the equipment in a lockable area so

that it is out of reach of children and unauthorized

persons.

• Ensure the machine is cleaned and that a complete

service is carried out before long-term storage.

• Secure the machine during transport.

Disposal of the battery, battery

charger and machine

Symbols on the product or its packaging indicate that this

product cannot be handled as domestic waste. It must

instead be submitted to an appropriate recycling station

for the recovery of electrical and electronic equipment.

By ensuring that this product is taken care of correctly,

you can help to counteract the potential negative impact

on the environment and people that can otherwise result

through the incorrect waste management of this product.

For more detailed information about recycling this

product, contact your municipality, your domestic waste

service or the shop from where you purchased the

product.

LED lights Battery status

All LEDs are lit Fully charged (67%-100%).

LED 1, LED 2 are lit.

The battery is 34%-66%

charged.

LED 1 is lit.

The battery is 1%-33%

charged.

LED 1 ﬂashes.

The battery is empty.

Charge the battery.

!

WARNING! Risk of electric shock and

short circuiting. Use approved and intact

wall sockets. Make sure that the cable is

not damaged. Replace cable if it appears

to be damaged in any way. Let your

authorized service agent repair any

damage on your product.

STARTING AND STOPPING

English – 13

Check before starting

Remove the battery from the machine by pressing the two

release buttons and pulling out the battery.

• Inspect the working area. Remove any objects that

could be thrown out.

• Check the cutting attachment. Never use blades that

are dull, cracked or damaged.

• Check that the machine is in perfect working order.

Check that all nuts and screws are tight.

• Only use the machine for the purpose it was intended

for.

• Make sure that the handle and safety features are in

good working order. Never use a machine that lacks a

part or has been modiﬁed outside its speciﬁcations.

Gloves should be worn when necessary.

• All covers must be correctly ﬁtted and undamaged

before you start the machine.

Connect battery to the machine

Make sure to use fully charged batteries. Use only a

Husqvarna original battery in your machine. See technical

data.

• Insert the battery in the machine. The battery should

slide easily into the battery holder on the machine. If

the battery does not slide in easily, it is not being

inserted correctly. The battery will lock itself into place

when you hear a click. Make sure the battery is ﬁtted

correctly to the machine.

(Figure 13)

Starting and stopping

Starting

• Turn on the machine. Press and hold the start button

(>1 sec.) until the green LED is lit.

(Figure 14)

• Press the power trigger on the front handle. (Figure

15)

• Then press the power trigger on the rear handle up to

apply full power.

(Figure 16)

Stopping

• Stop the machine by releasing the power trigger on

the rear handle or the power trigger on the front

handle and deactivate the machine.

Remove the battery from the machine by pressing the two

release buttons and pulling out the battery.

(Figure 17)

!

WARNING! Make sure no unauthorised

persons are in the working area.

Otherwise there is a risk of serious

personal injury. The safety distance is 15

meters.

IMPORTANT! Always remove the battery to prevent the

machine being started by accident.

WORKING TECHNIQUES

14 – English

General working instructions

Basic safety rules

• Never allow children to use or be in the vicinity of the

machine.

• Observe your surroundings and make sure that there

is no risk of people or animals coming into contact

with the cutting equipment.

• Never allow anyone else to use the machine without

ﬁrst ensuring that they have read and understood the

contents of the operator’s manual.

• Inspect the working area. Remove any objects that

could be thrown out.

• Never work from a ladder, stool or any other raised

position that is not fully secured.

(Figure 18)

• CAUTION! Do not use the machine unless you are

able to call for help in the event of an accident. Ensure

that no-one comes closer than 15 metres while you

are working.

• Never use the machine in bad weather, for instance in

fog, in rain, strong winds, intense cold, etc.

• If any foreign object is hit or if vibrations occur stop the

machine immediately. Remove the battery from the

machine and check that the machine is not damaged.

SavE mode

The machine is equipped with a battery saving function

(SavE). Activate the function by pressing the SavE button.

A green LED will light to indicate that the function is on.

(Figure 19)

In most cases SavE mode is the most optimum when

using the hedge trimmer and gives longest runtime.

Automatic switch off functionality

The machine is equipped with a shutdown feature that

deactivates the machine if not used. The green LED will

be extinguished and the machine turned off after 45

seconds.

Safety instructions while working

• Do not overreach. Keep proper footing and balance at

all times.

• Turn off the machine when it has to be moved.

• Never put the machine down without turning it off ﬁrst

and always remove the battery.

• Always use both hands to hold the machine. Hold the

machine at the side of your body.

(Figure 20)

• Make sure that no clothes or parts of the body come

in contact with the cutting equipment when it is

activated.

• When the motor is switched off, keep your hands and

feet away from the cutting attachment until it has

stopped completely.

• Watch out for stumps of branches that can be thrown

out during cutting. Do not cut too close to the ground.

Stones and other objects can be thrown out.

• Check the working area for foreign objects such as

electricity cables, insects and animals, etc, or other

objects that could damage the cutting attachment,

such as metal items.

• If anything jams in the blades while you are working,

switch off the motor and wait until it has stopped

completely before cleaning the blades. Remove the

battery from the machine.

• Never leave the machine unsupervised with the motor

running.

IMPORTANT!

This section takes up the basic safety precautions for

working with a hedge trimmer.

If you encounter a situation where you are uncertain

how to proceed you should ask an expert. Contact your

dealer or your service workshop.

Avoid all usage which you consider to be beyond your

capability.

!

WARNING! The machine can cause

serious personal injury. Read the safety

instructions carefully. Learn how to use

the machine.

!

WARNING! Cutting tool. Do not touch the

tool without ﬁrst deactivating the

machine. Always remove the battery

before any maintenance on the machine.

!

WARNING! Watch out for thrown objects.

Always wear approved eye protection.

Never lean over the cutting attachment

guard. Stones, rubbish, etc. can be

thrown up into the eyes causing

blindness or serious injury.

Keep unauthorised persons at a

distance. Children, animals, onlookers

and helpers should be kept outside the

safety zone of 15 metres. Stop the

machine immediately if anyone

approaches. Never swing the machine

around without ﬁrst checking behind you

to make sure no-one is within the safety

zone.

WORKING TECHNIQUES

English – 15

Safety instructions after completing work

• The transport guard should always be ﬁtted to the

cutting attachment when the machine is not in use.

• Make sure the cutting attachment has stopped before

cleaning, carrying out repairs or an inspection.

Remove the battery from the machine.

• Always wear heavy-duty gloves when repairing the

cutting attachment. The blades are very sharp and

can easily cause cuts.

• Store the machine out of reach of children.

• Use only original spare parts for repairs.

Basic working techniques

• Work with a swinging action from the bottom upwards

when trimming sides.

(Figure 21)

• When trimming a hedge the motor should always face

away from the hedge.

• Hold the machine as close to your body as possible to

get the best balance.

(Figure 20)

• Make sure that the tip does not touch the ground.

• Do not rush the work, but work steadily until all the

branches have been cut back cleanly.

MAINTENANCE

16 – English

Inspection and maintenance

All servicing and repair work on the machine requires

special training. This is especially true of the machine

′s

safety equipment. If your machine fails any of the checks

described below you must contact your service agent.

When you buy any of our products we guarantee the

availability of professional repairs and service. If the

retailer who sells your machine is not a servicing dealer,

ask him for the address of your nearest service agent.

Only use original spare parts.

Regularly check that the battery charger and the battery

are intact. (Figure 24) (Figure 25)

Cleaning

Gloves should be worn when necessary.

Clean the machine after use.

Make sure the battery and battery charger are clean and

that the terminals on the battery and the battery charger

are always clean and dry before the battery is placed in

the battery charger.

(Figure 22)

Keep the battery guide tracks clean. Clean plastic parts

with a clean and dry cloth.

Cleaning and lubrication

Clean any resin and plant residue from the blades using

cleaning agent before and after using the machine.

Check that the blade edges are not damaged or

deformed. File away any burrs. Check that the blades

move freely.

Lubricate the blade with special oil before long periods of

storage.

(Figure 23)

!

WARNING! Always remove the battery

before any maintenance on the machine.

IMPORTANT! Never clean the battery or the battery

charger with water.

Strong cleaning agents can damage the plastic.

English – 17

MAINTENANCE

Troubleshooting schedule

Keypad

Troubleshooting takes place from the keypad.

Troubleshooting the battery and/or the battery charger during charging.

Battery

Battery charger

Keypad Possible faults Possible action

Warning indicator ﬂashing.

No. 3 in ﬁgure (5).

Overload.

The cutting attachment is jamed.

Release the cutting attachment.

Temperature deviation. Allow the machine to cool down.

The machine does not start

The power trigger and the activate

button are pressed at the same time.

Release the power trigger and the

machine is active.

Warning indicator lit.

No. 3 in ﬁgure (5).

Service Contact your service agent.

LED display Possible faults Possible action

Warning indicator ﬂashing.

No. 2 in ﬁgure (27).

Temperature deviation.

Use the battery in surroundings

where temperatures are between -10

°C and 40 °C.

Over voltage.

Check that the mains voltage

corresponds with that stated on the

rating plate on the machine.

Remove the battery from the battery

charger.

Under voltage Charge the battery.

Warning indicator lit.

No. 2 in ﬁgure (27).

Cell difference too much (1V). Contact your service agent.

LED display Possible faults Possible action

Error LED ﬂashing Temperature deviation.

Use the battery charger only when the

surrounding temperature is between 5

°C and 40 °C.

Red LED on Cell difference too much (1V). Contact your service agent.

18 – English

MAINTENANCE

Maintenance schedule

The following is a list of the maintenance steps that must be performed on the machine. Most of the items are described

in the Maintenance section. The user must only carry out the maintenance and service work described in this Operator's

Manual. More extensive work must be carried out by an authorized service workshop.

!

WARNING! Always remove the battery

before any maintenance on the machine.

Let your authorized service agent repair

any damage on your product.

Maintenance

Daily

maintenance

Weekly

maintenance

Monthly

maintenance

Clean the outside of the machine. X

Check that the start and stop switch works correctly and is not

damaged.

X

Make sure that the power trigger on rear handle and the power

trigger on the front handle function correctly from a safety point

of view.

X

Check that all controls are undamaged and in working order. X

Check that the cutter and cutter guard are not damaged or

cracked. Replace the cutter or cutter guard if they have been

exposed to impact or if they are cracked.

X

Replace the cutting unit if it is bent or damaged. X

Check that the hand guard is not damaged. Replace the guard if

damaged.

X

Check that nuts and screws are tight. X

Check that the battery is intact. X

Check the battery's charge. X

Check that the battery charger is intact and functional. X

Check that the screws that hold the blades together are correctly

tightened.

X

Check the connections between the battery and the machine and

also check the connection between battery and the battery

charger.

X

English – 19

TECHNICAL DATA

Technical data

Note 1: Noise emissions in the environment measured as sound power (L

WA

) in conformity with EC directive 2000/14/

EC. The differnce between guaranteed and measured sound power is that the guaranteed sound power also includes

dispersion in the measurement result and the variations between different machines of the same model according to

Directive 2000/14/EC.

Note 2:

Reported data for equivalent sound pressure level for the machine has a typical statistical dispersion (standard deviation)

of 2,5 dB (A).

Note 3: Reported data for vibration level has a typical statistical dispersion (standard deviation) of 1,5 m/s

2

.

- The declared vibration total value has been measured in accordance with a standard test method and may be used

for comparing one tool with another.

- The declared vibration total value may also be used in a preliminary assessement of exposure.

Use only a Husqvarna original BLi battery in your machine.

Model designation Husqvarna 115iHD45

Platform HT100EU

Motor

Motor type BLDC

Weight

Weight without battery, kg 3,1

Weight with battery, kg 3.8

Cutter

Type Double sided

Blade length, mm 450

Blade speed cuts/min with SavE function activated 2400

Blade speed cuts/min with SavE function deactivated 3000

Noise emissions

(see note 1)

Sound power level, measured dB(A) 89

Sound power level, guaranteed L

WA

dB(A) 90

Sound levels

(see note 2)

Sound pressure level at the operator’s ear position,

measured according to EN 60745-1 and EN 60745-2-

15, dB (A):

77

Vibration levels

(see note 3)

Vibration levels (a

h

) at handles, measured according to

EN 60745-1 and EN 60745-2-15, m/s

2

.

2,4/4,7

Approved accessories

Battery BLi10 BLi20

Type Lithium-Ion Lithium-Ion

Battery capacity, Ah 2,1 (VTC4) 2 (HD2) 4,2 (VTC4) 4 (HD2)

Voltage, V 36 36,5 36 36,5

Weight, kg 0,7 0,7 1,2 1,2

20 – English

TECHNICAL DATA

EC Declaration of Conformity (Applies to Europe only)

Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare under sole responsibility that the hedge

trimmers

Husqvarna 115iHD45 (Platform: HT100EU) from 2016’s serial numbers and onwards (the year is clearly

stated in plain text on the type plate with subsequent serial number), are in conformity with the standards or or other

normative documents following the provisions in the COUNCIL’S DIRECTIVES:

- of May 17, 2006 ”relating to machinery” 2006/42/EC.

- of February 26, 2014 ”relating to electromagnetic compatibility” 2014/30/EU.

- of June 8, 2011 on the ”restriction of use of certain hazardous substances” 2011/65/EU.

- of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC.

For information relating to noise emissions, see the Technical data chapter.

The following standards have been applied:

EN 60745-1:2009/A11, EN 60745-2-15:2009/A1:2010, EN 55014-1:2006/A1:2009/A2:2011, EN 55014-2:2015, EN

61000-6-2:2005, EN 61000-4-2, EN 61000-4-3

Huskvarna, 29 August 2016

Lars Roos, Development manager (Authorized representative for Husqvarna AB and responsible for technical

documentation.)

Approved chargers for the speciﬁed batteries, BLi.

Battery charger QC80

Mains Voltage, V 100-240

Frequency, Hz 50-60

Power,W 100

Output Voltage, V d.c. / Amps, A 36/2

La pagina sta caricando ...

Husqvarna 115IHD45 Manuale del proprietario

Husqvarna 115IHD45 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti