HP Engage 3x16 Pole Display Guida utente

HP
Marca
HP
Modello
Engage 3x16 Pole Display
Tipo
Guida utente
User Guide
*M42381-001*
M42381-001
RMN: HSN-PD02
© Copyright 2020 HP Development Company, L.P.
All rights reserved. Android is a trademark of Google LLC. Linux® is the registered trademark of Linus
Torvalds in the U.S. and other countries. Microsoft and Windows are either registered trademarks or
trademarks of Microsoft Corporation in the United States and/or other countries. Enterprise Linux and Red
Hat are trademarks of Red Hat, Inc. in the United States and other countries.
The information contained herein is subject to change without notice. The only warranties for HP products
and services are set forth in the express warranty statements accompanying such products and services.
Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for
technical or editorial errors or omissions contained herein.
First Edition: October 2020
Document Part Number: M42381-001
Product notice
This user guide describes features that are common to most models. Some features may not be available
on your computer.
To access the latest user guides, go to http://www.hp.com/support, and follow the instructions to find your
product. Then select Manuals.
Software terms
By installing, copying, downloading, or otherwise using any software product preinstalled on this computer,
you agree to be bound by the terms of the HP End User License Agreement (EULA). If you do not accept
these license terms, your sole remedy is to return the entire unused product (hardware and software)
within 14 days for a full refund subject to the refund policy of your seller.
For any further information or to request a full refund of the price of the computer, please contact your
seller.
Contents
1. Introduction ........................................................................................................................................................... 4
1.1. Use and disclosure ............................................................................................................................................ 4
2. Specification .......................................................................................................................................................... 5
2.1. General specification ........................................................................................................................................ 5
2.2. Electrical specification ...................................................................................................................................... 6
2.2.1. Block diagram ........................................................................................................................................ 6
2.2.2. Power request ....................................................................................................................................... 6
2.2.3. Communication interface .................................................................................................................... 6
2.2.4. Mechanical drawing .............................................................................................................................. 7
3. Software ................................................................................................................................................................ 8
3.1. Supported operating systems ........................................................................................................................ 8
3.2. Command list ..................................................................................................................................................... 9
3.2.1. ULTIMATE command mode ................................................................................................................. 9
4. Appendix ............................................................................................................................................................. 11
4.1. Table 1 Codepage list ..................................................................................................................................... 11
4.2. Table 2 International character set ............................................................................................................. 11
1. Introduction
1.1. Use and disclosure
This document shall apply only to the product(s) identified herein. This technical specification defines the
requirements for HP Engage 3x16 Pole Display, using a USB bus power interface.
The supplier is requested to implement a change control process for tracking all changes, including
revision history. Devices shall be labeled and identifiable based on the revision. After the release to
production, all changes must be communicated as an Engineering Change.
2. Specification
2.1. General specification
Item
HSN-PD02
Display Method Vacuum Fluorescent Display (Blue-green)
Resolution 256 × 64 Dots
Display Mode
Alphanumeric:
32 digits × 3 lines
32 digits × 4 lines
Character Dot Matrix
8 × 16 dots for single-byte characters
16 × 16 dots for double-bytes characters
Dot Size 0.49 (W) × 0.48 (H) mm
Dot Pitch 0.64 (H) × 0.63 (V) mm
Viewing Direction Maximum 90°
Average Brightness 600 cd/m
2
Character type Alphanumeric and Compound (2-Bytes) Words
Character size
Font 8 × 16 – 4.97 (W) × 9.93 (H) mm
Font 16 × 16 – 10.09 (W) × 9.93 (H)mm
User Define Character 96 characters
Viewing Area 163.69(W)X40.17 (H) mm
Module Dimension 230 (L) × 66.5 (W) × 26 (D) mm
Top Head Dimension 240 (L) × 95 (W) × 49 (D) mm
Viewing Angle Maximum 90°
Net Weight Approximately 1650 grams
Commands Mode UITIMATE
Language
US English, Japanese
Interface USB
Baud rate Direct connection 9600 or 19200 bps
MTBF 30,000 hours
Power Consumption 12 V – 400 mA
EMC / Safety standards
CB, VCCI
2.2. Electrical specification
2.2.1. Block diagram
2.2.2. Power request
Voltage (typical): 12 VDC +/- 10%
Current consumption (typical): 400 mA
2.2.3. Communication interface
Interface USB (Virtual COM Port)
The default protocol of the virtual RS232 port is 9600 bps, non-parity, 8 data bits,
1 stop bit and with DTR/DSR control.
VFD
MCU
USB UART
Control & Data
Power
USB INPUT
DC INPUT
EEPROM
2.2.4. Mechanical drawing
3. Software
3.1. Supported operating systems
Windows
Windows® 10
Windows 8.1/8 Pro (64 and 32 bit)
Windows Embedded 8.1/8 Industry
Windows Embedded POSReady 7 (64 and 32 bit)
Windows 7 Professional (64 and 32 bit)
Windows Embedded POSReady 2009
Linux
Red Hat® Enterprise Linux®/CentOS 6 (64 and 32 bit) and newer
Suse Linux® Enterprise Point of Service 11 (64 or 32 bit) and newer
Ubuntu 12.04 LTS (64 or 32 bit) and newer
Android
Android™ 4.0 and newer
3.2. Command list
3.2.1. ULTIMATE command mode
Command Hex
Function Description
HT 09
Move cursor right
BS 08
Move cursor left
US LF 1F 0A
Move cursor up
LF 0A
Move cursor down
US CR 1F 0D
Move cursor to right-most position
CR 0D
Move cursor to left-most position
HOM 0B
Move cursor to home position
US B 1F 42
Move cursor to bottom position
US $ x y 1F 24 x y
Move cursor to specified position
1≦x(column)≦20 ; 1≦y(row)≦2
US C n 1F 43 n
Select/cancel cursor display
n=0, canceled ; n=1, selected
CLR 0C
Clear display screen
CAN 18
Clear cursor line
US X n 1F 58 n
Brightness adjustment
1
≦
n
≦
4
US E n 1F 45 n
Blink display screen
0
≦
n
≦
255 (n*50msec) ON / (n*50msec) OFF
n=0, blinking is canceled
n=255, display is turned off
ESC @ 1B 40
Initialize display
ESC t n 1B 74 n
Select character code table (see Table 1)
ESC R n 1B 52 n
Select international character set (see Table 2)
US r n 1F 72 n
Select/cancel reverse character
n=0, canceled; n=1, selected
US MD1 1F 01
Specify overwrite mode
US MD2 1F 02
Specify vertical scroll mode
US MD3 1F 03
Specify horizontal scroll mode
US T h m 1F 54 h m
Set and display time
0
≦
h
≦
23 ; 0
≦
m
≦
59
US U 1F 55
Display of time counter
ESC u E..CR 1B 75 45 hh 3A mm 0D
Set and display 24-hour time
0x30
≦
h ,m
≦
0x39
ESC u 1..CR 1B 75 49 [data x 40] 0D
Two-line display
ESC [ D 1B 5B 44
Move cursor left
ESC [ C 1B 5B 43
Move cursor right
ESC [ A 1B 5B 41
Move cursor up
ESC [ B 1B 5B 42
Move cursor down
ESC [ H 1B 5B 48
Move cursor to home position
ESC [ L 1B 5B 4C
Move cursor to left-most position
ESC [ R 1B 5B 52
Move cursor to right-most position
ESC [ K 1B 5B 4B
Move cursor to bottom position
ESC l x y
1B 6C x y
Move cursor to specified position
1
≦
x
≦
20, y=1,2
ESC u A..CR 1B 75 41 [data x 32] 0D
Display data on line 1
ESC u B..CR 1B 75 42 [data x 32] 0D
Display data on line 2
ESC u C..CR 1B 75 43 [data x 32] 0D
Display data on line 3
GS r A
1D 72 41 [data x 96] 0D
Marquee on line 1
GS r B
1D 72 42 [data x 96] 0D
Marquee on line 2
GS r C
1D 72 43 [data x 96] 0D
Marquee on line 3
GS r D
1D 72 44 [data x 96] 0D
Marquee on line 4
4. Appendix
4.1. Table 1 Codepage list
Page
Codepage Language
Dec Hex
0 0x00 PC437 USA, Standard Europe
1 0x01 Katakana Japanese
244 0xF4 CP932 Japanese Shift JIS
4.2. Table 2 International character set
Index n
Country
ASCII code
Dec Hex
23 24 40 5B 5C 5D 5E 60 7B 7C 7D 7E
00 00
USA # $ @ [ \ ] ^ ` { | } ~
01 01
France # $ à ° ç § ^ ` é ù è ¨
02 02
Germany # $ § Ä Ö Ü ^ ` ä ö ü β
03 03
U.K. £ $ @ [ \ ] ^ ` { | } ~
04 04
Denmark I # $ @ Æ Ø Å ^ ` æ ø å ~
05 05
Sweden # ¤ É Ä Ö Å Ü é ä ö å ü
06 06
Italy # $ @ ° \ é ^ ù à ò è ì
07 07
Spain I Pt $ @ ¡ Ñ ¿ ^ ` ¨ ñ } ~
08 08
Japan # $ @ [ ¥ ] ^ ` { | } ~
09 09
Norway # ¤ É Æ Ø Å Ü é æ ø å ü
10 0A
Denmark II # $ É Æ Ø Å Ü é æ ø å ü
11 0B
Spain II # $ á ¡ Ñ ¿ é ` í ñ ó ú
12 0C
Latin America # $ á ¡ Ñ ¿ é ü í ñ ó ú
13 0D
Korea # $ @ [
₩
] ^ ` { | } ~
14 0E
Slovenia/Croatia # $ Ž Š Đ Ć Č ž š đ ć č
15 0F
China # Ұ @ [ \ ] ^ ` { | } ~
16 10
Vietnam ₫ $ @ [ \ ] ^ ` { | } ~
17 11 Slovakia
# $ @ [ \ ] ^ ` { | } ~
18 12 Russia
# $ @ [ \ ] ^ ` { | } ~
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11

HP Engage 3x16 Pole Display Guida utente

HP
Marca
HP
Modello
Engage 3x16 Pole Display
Tipo
Guida utente
Scarica il pdf
rapporto

in altre lingue

Altri documenti