Hitachi WR 12DM2 Handling Instructions Manual

Cordless Impact Driver/Wrench

Akku-Schlagschrauber

Perceuse/visseuse à percussion sur batterie

Avvitatore a impulso a batteria per viti e bulloni

Snoerloze slagschroevendraaier/sleutel

Atornillador/Llave de impacto a batería

Aparafusadora/ Chave de impacto a bateria

¢Ú··ÓÔÎ·ÙÛ¿‚È‰Ô ª·Ù·Ú›·˜/∫ÏÂÈ‰›

Read through carefully and understand these instructions before use.

Diese Anleitung vor Benutzung des Werkzeugs sorgfältig durchlesen und verstehen.

Lire soigneusement et bien assimiler ces instructions avant usage.

Prima dell’uso leggere attentamente e comprendere queste istruzioni.

Deze gebruiksaanwijzing s.v.p. voor gebruik zorgvuldig doorlezen.

Leer

cuidadosamente y comprender estas instrucciones antes del uso.

Antes de usar, leia com cuidado para assimilar estas instruções.

∆ιαάστε πρσεκτικά και κατανήσετε αυτές τις δηγίες πριν τη ρήση.

Handling instructions

Bedienungsanleitung

Mode d’emploi

Istruzioni per l’uso

Gebruiksaanwijzing

Instrucciones de manejo

Instruções de uso

δηγίες ειρισµύ

English

EC DECLARATION OF CONFORMITY

We declare under our sole responsibility that this

product is in conformity with standards or standardized

documents EN50144 and EN55014-2 in accordance with

Council Directives 89/336/EEC and 98/37/EC.

This declaration is applicable to the product affixed CE

marking.

Deutsch

ERKLÄRUNG ZUR KONFORMITÄT MIT CE-REGELN

Wir erklären mit alleiniger Verantwortung, daß dieses

Produkt den Standards oder standardisierten

Dokumenten EN50144 und EN55014-2 in

Übereinstimmung mit den Direktiven des Europarats

89/336/EWG und 98/37/CE entspricht.

Diese Erklärung gilt für Produkte, die die CE-Markierung

tragen.

Français

DECLARATION DE CONFORMITE CE

Nous déclarons sous notre seule et entière responsabilité

que ce produit est conforme aux normes ou documents

normalisés EN50144 et EN55014-2 en accord avec les

Directives 89/336/CEE et 98/37/CE du Conseil.

Cette déclaration s’applique aux produits désignés CE.

Italiano

DICHIARAZIONE DI CONFORMITÀ CE

Si dichiara sotto nostra responsabilità che questo

prodotto è conforme agli standard o ai documenti

standardizzati EN50144 e EN55014-2 conforme alle

direttive 89/336/CEE e 98/37/CE del concilio.

Questa dichiarazione è applicabile ai prodotti cui sono

applicati i marchi CE.

412

Code No. C99129872 N

Printed in Japan

Hitachi Koki Co., Ltd.

Variable speed

WH 12DM2 • WR 12DM2 • WH 12DMR

WH 9DM2 • WR 9DM2

Representative office in Europe

Hitachi Power Tools Europe GmbH

Siemensring 34, 47877 Willich 1, F. R. Germany

Head office in Japan

Hitachi Koki Co., Ltd.

Shinagawa Intercity Tower A, 15-1, Konan 2-chome,

Minato-ku, Tokyo, Japan

30. 7. 2004

K. Kato

Board Director

1

4

3

6

5

87

1

I

Nederlands

EC VERKLARING VAN CONFORMITEIT

Wij verklaren onder eigen verantwoordelijkheid dat dit

produkt conform de richtlijnen of gestandardiseerde

documenten EN50144 en EN55014-2 voldoet aan de

eisen van EEG Bepalingen 89/336/EEG en 98/37/EC.

Deze verklaring is van toepassing op produkten

voorzien van de CE-markeringen.

Español

DECLARACIÓN DE CONFORMIDAD DE LA CE

Declaramos bajo nuestra única responsabilidad que

este producto está de acuerdo con las normas o con

los documentos de normalización EN50144 y EN55014-

2 según indican las Directrices del Consejo 89/336/CEE

y 98/37/CE.

Esta declaración se aplica a los productos con marcas

de la CE.

Português

DECLARAÇÃO DE CONFORMIDADE CE

Declaramos, sob nossa única e inteira responsabilidade,

que este produto está de acordo com as normas ou

documentos normativos EN50144 e EN55014-2 em

conformidade com as Diretrizes 89/336/CEE e 98/37/CE

do Conselho.

Esta declaração se aplica aos produtos designados CE.

Ελληνικά

EK ∆ΗΛΩΣΗ ΕΝΑΡΜΝΙΣΜΥ

∆ηλώνυµε µε απ'λυτη υπευθυν'τητα 'τι αυτ' τ

πρι'ν είναι εναρµνισµέν µε τα πρ'τυπα ή τα

έγρα)α πρτύπων EN50144 και EN55014-2 σε

συµ)ωνία µε τις δηγίες τυ Συµυλίυ 89/336/EOK

και 98/37/EK.

Αυτή η δήλωση ισύει στ πρι'ν µε τ σηµάδι EC.

1

F

E

2

4

3

1

5

6

9

8

7

B

C

0

A

D

F

D

G

H

F

D

J

WH12DM2 WR12DM2

1

3

2

3

WH12DMR

D

I

K

F

Cordless Impact Driver/Wrench

Akku-Schlagschrauber

Perceuse/visseuse à percussion sur batterie

Avvitatore a impulso a batteria per viti e bulloni

Snoerloze slagschroevendraaier/sleutel

Atornillador/Llave de impacto a batería

Aparafusadora/ Chave de impacto a bateria

¢Ú··ÓÔÎ·ÙÛ¿‚È‰Ô ª·Ù·Ú›·˜/∫ÏÂÈ‰›

Read through carefully and understand these instructions before use.

Diese Anleitung vor Benutzung des Werkzeugs sorgfältig durchlesen und verstehen.

Lire soigneusement et bien assimiler ces instructions avant usage.

Prima dell’uso leggere attentamente e comprendere queste istruzioni.

Deze gebruiksaanwijzing s.v.p. voor gebruik zorgvuldig doorlezen.

Leer

cuidadosamente y comprender estas instrucciones antes del uso.

Antes de usar, leia com cuidado para assimilar estas instruções.

∆ιαάστε πρσεκτικά και κατανήσετε αυτές τις δηγίες πριν τη ρήση.

Handling instructions

Bedienungsanleitung

Mode d’emploi

Istruzioni per l’uso

Gebruiksaanwijzing

Instrucciones de manejo

Instruções de uso

δηγίες ειρισµύ

English

EC DECLARATION OF CONFORMITY

We declare under our sole responsibility that this

product is in conformity with standards or standardized

documents EN50144 and EN55014-2 in accordance with

Council Directives 89/336/EEC and 98/37/EC.

This declaration is applicable to the product affixed CE

marking.

Deutsch

ERKLÄRUNG ZUR KONFORMITÄT MIT CE-REGELN

Wir erklären mit alleiniger Verantwortung, daß dieses

Produkt den Standards oder standardisierten

Dokumenten EN50144 und EN55014-2 in

Übereinstimmung mit den Direktiven des Europarats

89/336/EWG und 98/37/CE entspricht.

Diese Erklärung gilt für Produkte, die die CE-Markierung

tragen.

Français

DECLARATION DE CONFORMITE CE

Nous déclarons sous notre seule et entière responsabilité

que ce produit est conforme aux normes ou documents

normalisés EN50144 et EN55014-2 en accord avec les

Directives 89/336/CEE et 98/37/CE du Conseil.

Cette déclaration s’applique aux produits désignés CE.

Italiano

DICHIARAZIONE DI CONFORMITÀ CE

Si dichiara sotto nostra responsabilità che questo

prodotto è conforme agli standard o ai documenti

standardizzati EN50144 e EN55014-2 conforme alle

direttive 89/336/CEE e 98/37/CE del concilio.

Questa dichiarazione è applicabile ai prodotti cui sono

applicati i marchi CE.

412

Code No. C99129872 N

Printed in Japan

Hitachi Koki Co., Ltd.

Variable speed

WH 12DM2 • WR 12DM2 • WH 12DMR

WH 9DM2 • WR 9DM2

Representative office in Europe

Hitachi Power Tools Europe GmbH

Siemensring 34, 47877 Willich 1, F. R. Germany

Head office in Japan

Hitachi Koki Co., Ltd.

Shinagawa Intercity Tower A, 15-1, Konan 2-chome,

Minato-ku, Tokyo, Japan

30. 7. 2004

K. Kato

Board Director

1

4

3

6

5

87

1

I

Nederlands

EC VERKLARING VAN CONFORMITEIT

Wij verklaren onder eigen verantwoordelijkheid dat dit

produkt conform de richtlijnen of gestandardiseerde

documenten EN50144 en EN55014-2 voldoet aan de

eisen van EEG Bepalingen 89/336/EEG en 98/37/EC.

Deze verklaring is van toepassing op produkten

voorzien van de CE-markeringen.

Español

DECLARACIÓN DE CONFORMIDAD DE LA CE

Declaramos bajo nuestra única responsabilidad que

este producto está de acuerdo con las normas o con

los documentos de normalización EN50144 y EN55014-

2 según indican las Directrices del Consejo 89/336/CEE

y 98/37/CE.

Esta declaración se aplica a los productos con marcas

de la CE.

Português

DECLARAÇÃO DE CONFORMIDADE CE

Declaramos, sob nossa única e inteira responsabilidade,

que este produto está de acordo com as normas ou

documentos normativos EN50144 e EN55014-2 em

conformidade com as Diretrizes 89/336/CEE e 98/37/CE

do Conselho.

Esta declaração se aplica aos produtos designados CE.

Ελληνικά

EK ∆ΗΛΩΣΗ ΕΝΑΡΜΝΙΣΜΥ

∆ηλώνυµε µε απ'λυτη υπευθυν'τητα 'τι αυτ' τ

πρι'ν είναι εναρµνισµέν µε τα πρ'τυπα ή τα

έγρα)α πρτύπων EN50144 και EN55014-2 σε

συµ)ωνία µε τις δηγίες τυ Συµυλίυ 89/336/EOK

και 98/37/EK.

Αυτή η δήλωση ισύει στ πρι'ν µε τ σηµάδι EC.

1

F

E

2

4

3

1

5

6

9

8

7

B

C

0

A

D

F

D

G

H

F

D

J

WH12DM2 WR12DM2

1

3

2

3

WH12DMR

D

I

K

F

2

3

1211

14

13

O

Q

P

109

L

R

XX

16

15

2019

21

1817

L

(A)

5

4

1

(B)

2

3

M

N

3

L

R

L

T

S

U

V

U

T

,

.

,.

Y

Z

[

3mm

11.5mm

128

\

W

2

3

1211

14

13

O

Q

P

109

L

R

XX

16

15

2019

21

1817

L

(A)

5

4

1

(B)

2

3

M

N

3

L

R

L

T

S

U

V

U

T

,

.

,.

Y

Z

[

3mm

11.5mm

128

\

W

4

English Deutsch Français Italiano

1

2

3

4

5

6

7

8

9

0

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

R

S

T

U

V

W

X

Y

Z

[

\

12 V Rechargeable

battery (For WH12DM2,

WR12DM2, WH12DMR)

9.6 V Rechargeable

battery (For WH9DM2,

WR9DM2)

Latch

Handlee

Insert

Pull out

Insert

Pilot lamp

Hole for connecting the

rechargeable battery

Movement

Guide sleeve

Hexagonal hole in the

anvil

Driver bit

Hexagonal socket

Groove

Anvil

Ring

Hole

Plunger

Retaining ring

Hook

Spring

Larger diameter faces

away

Switch

Phillips-head screwdriver

Screw

Arrow

Hook cover

Indentation

Protuberance

AAAA batteries

Push button

Push

Wear limit

Nail of carbon brush

Protrusion of carbon

brush

Contact portion outside

brush tube

Batteria ricaricabile,

12 V (Per WH12DM2,

WR12DM2, WH12DMR)

Batteria ricaricabile,

9,6 V (Per WH9DM2,

WR9DM2)

Fermo

Impugnatura

Inserire

Estrarre

Inserire

Spia

Foro di collegamento

della batería recargable

Movimento

Manicotto guida

Foro esagonale nel

basaménto

Testa avvitatrice

Chiave de incavo

esagonale

Scanalature

Basamento

Spina

Anello

Foro

Stantuffo

Anello di trattenimento

Grancio

Molla

Diametro più grande

lontano da sé

Interruttore

Cacciavite con testa a

croce

Vite

Freccia

Coperchio gancio

Tacca

Sporgenza

Pile AAAA

Tasto da premere

Spingere

Limite di usura

Chiodo di spazzola di

carbone

Sporgenza di spazzola

di carbone

Parte di contatto fuori

dal tubo spazzola

Akkumulator, 12 V

(Für WH12DM2,

WR12DM2, WH12DMR)

Akkumulator, 9,6 V

(Für WH9DM2,

WR9DM2)

Schnapper

Griff

Einsatz

Herausziehen

Einsetz

Kontrollampe

Anschlußlon für

Akkumulator

Bewegung

Führungsmanschette

Sechskantloch in der

Schabotte

Dreherspitze

Sechskantbuchse

Schlitz

Schabotte

Stift

Ring

Öffnung

Preßkolben

Haltering

Haken

Feder

Der große Durchmesser

weist zur anderen Seite

Schalter

Kreuzschlitzschrauben-

zieher

Schraube

Pfeil

Hakenabdeckung

Einkerbung

Vorsprung

Batterien der Größe

AAAA

Druckknopf

Drücken

Verschließgrenze

Klaue der Kohlebürste

Krempe der Kohlebürste

Kontaktteil außerhalb

des Bürstenrohrs

Batterie rechargeable,

12 V (Pour WH12DM2,

WR12DM2, WH12DMR)

Batterie rechargeable,

9,6 V (Pour WH9DM2,

WR9DM2)

Loquet

Poignée

Insérer

Tirer

Insérer

Lampe pilote

Orifice de raccordement

de la batterie rechargeable

Mouvement

Manchon-guide

Orifice hexagonal de la

chabotte

Mèche

Douille hexagonal

Rainure

Chabotte

Goupille

Aunneau

Orifice

Piston

Bague de retenue

Crochet

Ressort

Gros diamètre dirigé

vers l’extérieur

Interrupteur

Tournevis à tête Phillips

Vis

Flèche

Cache de crochet

Entaille

Saillie

Piles AAAA

Poussoir

Pousser

Limite d'usure

Clou de balai en

carbone

Saillie de balai en

carbone

Section de contact à

l’extérieur du tube de

balai

5

Nederlands Español Português Ελληνικά

1

2

3

4

5

6

7

8

9

0

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

R

S

T

U

V

W

X

Y

Z

[

\

Oplaadbare batterij, 12 V

(Voor WH12DM2,

WR12DM2, WH12DMR)

Oplaadbare batterij, 9,6

V (Voor WH9DM2,

WR9DM2)

Vergrendeling

Handgreep

Insteken

Uittrekken

Insteken

Kontrolelampje

Aansluiting voor

oplaadbare batterij

Beweging

Geleide ring

Zeshoekige opening in

het draaistuk

Schroefstuk

Zeschoekige bus

Groef

Draaistuk

Pen

Ring

Opening

Plunjer

Borgring

Haak

Veer

De grotere diameter wijst

van u vandaan

Schakelaar

Kruiskopschroevendraaier

Schroef

Pijl

Afdekking haak

Inkeping

Uitsteeksel

AAAA batterijen

Druktoets

Drukken

Slijtagegrens

Nagel van koolborstel

Uitsteeksel van

koolborstel

Contact-gedeelte buiten

de borstelbuis

12 V Επαναρτιµενη

µπαταρία (Για WH12DM2,

WR12DM2, WH12DMR)

9,6 V Επαναρτιµενη

µπαταρία (Για WH9DM2,

WR9DM2)

Μάνδαλ

ερύλι

Εισωρήστε

Βραήτε έω

Εισωρήστε

∆κιµαστική λάµπα

Τρύπα για την σύνδεση

της επαναρτιµενης

µπαταρίας

Κίνηση

%δηγητικς ραίνας

Εάγωνη τρύπα στν

άκµνα

Λεπίδα κίνησης

Μακριά υπδή

Αυλάκωση

Άκµνας

Πείρς

∆ακτύλις

Τρύπα

Έµλ

∆ακτύλις συγκράτησης

Άγκιστρ

Ελατήρι

Η µεγαλύτερη

διάµετρς λέπει πρς

άλλη κατεύθυνση

∆ιακπτης

Κατσαίδι κεαλής

Phillips

Βίδα

Βέλς

Κάλυµµα αγκίστρυ

Αυλάκωση

Πρεή

ΑΑΑΑ µπαταρίες

Κυµπί ώθησης

Σπρώε

5ρι θράς

Καρί καρυνακιύ

Πρεή

καρυνακιύ

Τµήµα επαής έω

απ τ σωλήνα της

ψήκτρας

Bateria de 12 V recarregável

(Para WH12DM2,

WR12DM2, WH12DMR)

Bateria de 9,6 V

recarregável (Para

WH9DM2, WR9DM2)

Lingüeta

Cabo

Inserir

Retirar

Inserir

Lâmpada piloto

Orifício para conectar a

bateria recarregável

Movimento

Manga-guia

Orifício sextavado na

bigorna

Chave de fenda

Encaixe longo

Ranhura

Bigorna

Pino

Anel

Orifício

Pistão

Anel de retenção

Gancho

Mola

O diâmetro maior dá

para fora

Comutador

Chave Phillips

Parafuso

Seta

Tampa do gancho

Entalhe

Protuberância

Pilhas AAAA

Interruptor

Apertar

Limite de desgaste

Prego da escova de

carvão

Saliência da escova de

carvão

Segmento de contato

no exterior do tubo da

escova

Batería recargable,

12 V (Para WH12DM2,

WR12DM2, WH12DMR)

Batería recargable,

9,6 V (Para WH9DM2,

WR9DM2)

Enganche

Mango

Insertar

Sacar

Insertar

Lámpara piloto

Agujero para conectar

la batería recargable

Movimiento

Manguito guía

Orificio hexagonal en el

yunque

Punta de destornillador

Recaptáculo hexanogal

Ranura

Yunque

Pasador

Anillo

Orificio

Embolo

Anillo de retención

Gancho

Resorte

El diámetro más grande

queda en dirección

opuesta

Interruptor

Destornillador con cabeza

Phillips

Tornillo

Flecha

Cubierta del gancho

Indentación

Saliente

Pilas AAAA

Pulsador

Presionar

Límite de uso

Uña de escobilla de

carbón

Saliente de escobilla de

carbón

Tubo exterior de la

parte de contacto de la

escobilla de carbón

English

6

GENERAL OPERATIONAL PRECAUTIONS

1. Keep work area clean. Cluttered areas and benches

invite accidents.

2. Avoid dangerous environment. Don’t expose power

tools and charger to rain. Don’t use power tools

and charger in damp or wet locations. And keep

work area well lit. Never use power tools and

charger near flammable or explosive materials.

Do not use tool and charger in presence of

flammable liquids or gases.

3. The appliance is not intended for use by young

children or infirm persons without supervision.

Young children should be supervised to ensure

that they do not play with the appliance. All visitors

should be kept safe distance from work area.

4. Store idle tools and charger. When not in use,

tools and charger should be stored in dry, high

or locked-up place – out of reach of the children

and infirm persons. Store tools and charger in a

place where the temperature is less than 40°C.

5. Don’t force tool. It will do the job better and safer

at the rate for which it was designed.

6. Use right tool. Don’t force small tool or attachment

to do the job of a heavy duty tool.

7. Wear proper apparel. Do not wear loose clothing

or jewelry. They can be caught in moving parts.

Rubber gloves and non-skid footwears are

recommended when working outdoor.

8. Use eye protection with most tools. Also use face

or dust mask if cutting operation is dusty.

9. Don’t abuse cord. Never carry charger by cord or

yank it to disconnect from receptacle. Keep cord

from heat, oil and sharp edges.

10. Secure work. Use clamps or a vise to hold work.

It’s safer than using your hand and it frees both

hands to operate tool.

11. Don’t overreach. Keep proper footing and balance

at all times.

12. Maintain tools with care. Keep tools sharp at all

times, and clean for best and safest performance.

Follow instructions for lubricating and changing

accessories.

13. When the charger is not in use, or when being

maintained and inspected, disconnect its power

cord from the receptacle.

14. Remove chuck wrenches and wrenches. Form habit

of checking to see that wrenches are removed

from tool before turning it on.

15. Avoid accidental starting. Don’t carry tool with

finger on switch.

16. To avoid danger, always use only the specified

charger.

17. Use only genuine HITACHI replacement parts.

18. Do not use power tools for applications other than

those specified in the Handling Instructions.

19. To avoid personal injury, use only the accessories

or attachment recommended in these handling

instructions or in the HITACHI catalog.

20. Let only the authorized service center do the

repairing. The Manufacturer will not be responsible

for any damages or injuries caused by repair by

the unauthorized persons or by mishandling of

the tool.

21. To ensure the designed operational integrity of

power tools and charger, do not remove installed

covers or screws.

22. Always use the charger at the voltage specified

on the nameplate.

23. Do not touch movable parts or accessories unless

the power source has been disconnected.

24. Always charge the battery before use.

25. Never use a battery other than that specified. Do

not connect a usual dry cell, a rechargeable battery

other than that specified or a car battery to the

power tool.

26. Do not use any transformer that has a booster.

27. Do not charge the battery from an engine electric

generator or DC power supply.

28. Always charge indoors. Because the charger and

battery heat slightly during charging, charge the

battery in a place not exposed to direct sunlight;

where the humidity is low and the ventilation is

good.

29. Before starting to work in a high place, pay

attention to the activities below to make sure

there are no people below.

30. Use the exploded assembly drawing on this

handling instructions only for authorized servicing.

31. If the supply cord is damaged, it must be replaced

by the manufacture or its service agent or a

similarly qualified person in order to avoid a

hazard.

PRECAUTIONS FOR CORDLESS IMPACT

DRIVER

1. This is portable tool for tightening and loosenig

screws. Use it only for these operation.

2. Use the earplugs if using for a long time.

3. One-hand operation is extremely dangerous; hold

the unit firmly with both hands when operating.

4. After installing the driver bit, pull lightly out the

bit to make sure that it does not come loose. If

the bit is not installed properly, it can come loose

during use, which can be dangerous.

5. Use the bit that matches the screw.

6. Tightening a screw with the impact driver at an

angle to that screw can damage the head of the

screw and the proper force will not be transmitted

to the screw. Tighten with this impact driver lined

up straight with the screw.

7. Always charge the battery at a temperature of 0

– 40°C.

A temperature of less than 0°C will result in over

charging which is dangerous. The battery cannot

be charged at a temperature greater than 40°C.

The most suitable temperature for charging is that

of 20 – 25°C.

8. Do not use the charger continuously.

When one charging is completed, leave the charger

for about 15 minutes before the next charging of

battery.

9. Do not allow foreign matter to enter the hole for

connecting the rechargeable battery.

10. Never disassemble the rechargeable battery and

charger.

11. Never short-circuit the rechargeable battery.

Short-circuiting the battery will cause a great

electric current and overheat. It results in burn or

damage to the battery.

12. Do not dispose of the battery in fire.

If the battery burnt, it may explode.

13. Do not insert object into the air ventilation slots

of the charger.

Inserting metal objects or inflammables into the

charger air ventilation slots will result in electrical

shock hazard or damaged charger.

14. Bring the battery to the shop from which it was

purchased as soon as the post-charging battery

life becomes too short for practical use. Do not

dispose of the exhausted battery.

15. Using an exhausted battery will damage the

charger.

English

7

PRECAUTIONS FOR CORDLESS IMPACT

WRENCH

1. This is a portable tool for tightening and loosening

bolts and nuts. Use it only for these operation.

2. Use the earplugs if using for a long time.

3. One-hand operation is extremely dangerous; hold

the unit firmly with both hands when operating.

4. Check that the socket is not cracked or broken.

Broken or cracked sockets are dangerous. Check

the socket before using it.

5. Secure the socket with the socket pin and the ring.

If the socket pin or ring securing the socket is damaged,

the socket may come off from the impact wrench,

which is quite dangerous. Do not use socket pins

or rings that are deformed, worn out, cracked, or in

any other way damaged. Always make sure to install

the socket pin and ring in the correct position.

6. Check the tightening torque.

The appropriate torque for tightening a bolt

depends on the material the bolt is made of, its

dimensions, grade, etc.

Also, the tightening torque generated by this impact

wrench depends on the materials and dimensions

of the bolt, how long the impact wrench is applied

for the way in which the socket is installed, etc.

Also the torque when the battery has just been

charged and when it is about to run out are slightly

different. Use a torque wrench to check that the

bolt has been tightened with the appropriate torque.

7. Stop the impact wrench before switching the

direction of rotation. Always release the switch

and wait for impact wrench to stop before

switching the direction of rotation.

8. Never touch the turning part.

Do not allow the turning socket section to get near

your hands or any other part of your body. You could

be cut or caught in the socket. Also, be careful not

to touch the socket after using continuously it for a

long time. It gets quite hot and could burn you.

9. Never let the impact wrench turn without a load

when using the universal joint.

If the socket turns without being connected to a load,

the universal joint causes the socket to turn wildly.

You could get hurt or the movement of the socket

could shake the impact wrench so much as to

make you drop it.

10. Always charge the battery at a temperature of 0

– 40°C.

A temperature of less than 0°C will result in over

charging which is dangerous. The battery cannot

be charged at a temperature greater than 40°C.

The most suitable temperature for charging is

that of 20 – 25°C.

11. Do not use the charger continuously.

When one charging is completed, leave the charger

for about 15 minutes before the next charging of

battery.

12. Do not allow foreign matter to enter the hole for

connecting the rechargeable battery.

13. Never disassemble the rechargeable battery and

charger.

14. Never short-circuit the rechargeable battery.

Short-circuiting the battery will cause a great

electric current and overheat. It results in burn

or damage to the battery.

15. Do not dispose of the battery in fire.

If the battery burnt, it may explode.

16. Do not insert object into the air ventilation slots

of the charger.

Inserting metal objects or inflammables into the

charger air ventilation slots will result in electrical

shock hazard or damaged charger.

17. Bring the battery to the shop from which it was

purchased as soon as the post-charging battery

life becomes too short for practical use. Do not

dispose of the exhausted battery.

18. Using an exhausted battery will damage the

charger.

MODEL

WH12DM2: with charger and case

WH9DM2: with charger and case

WH12DMR: with charger and case

WR12DM2: with charger and case

WR9DM2: with charger and case

SPECIFICATIONS

Cordless Impact Driver

Model WH9DM2 (9.6 V) WH12DM2 (12 V) WH12DMR (12 V)

No-load speed 0 – 2800 min

–1

0 – 2600 min

–1

Capacity M4 – M8 (Small screw)

M5 – M12 (Ordinary bolt)

M5 – M10 (High tension bolt)

Tightening torque

Rechargeable battery

EB9B: Ni-Cd battery, 9.6 V

EB1220BL: Ni-Cd battery, 12 V

(2.0 Ah 8 cells) (2.0 Ah 10 cells)

EB926H: Ni-MH battery, 9.6 V

EB1226HL: Ni-MH battery, 12 V

(2.6 Ah 8 cells) (2.6 Ah 10 cells)

EB930H: Ni-MH battery, 9.6 V

EB1230HL: Ni-MH battery, 12 V

(3.0 Ah 8 cells) (3.0 Ah 10 cells)

Weight 1.2 kg 1.6 kg

Maximum 80 N·m

{820 kgf·cm}

Tightening is M12 high

tension bolt (strength

grade 12.9), when fully

charged at 20°C temp.

Tightening time: 3 sec.

Maximum 135 N·m Maximum 130 N·m

{1375 kgf·cm}

{1330 kgf·cm}

Tightening is M14 high tension bolt (strength grade

12.9), when fully charged at 20°C temp.

Tightening time: 3 sec.

English

8

Part Name

Engraved

LBCode No.

characters

5 mm Hexagonal socket 8 65 8 996177

6 mm Hexagonal socket 10 65 10 985329

5/16" Hexagonal socket 12 65 12 996178

8 mm Hexagonal socket 13 65 13 996179

Bit No. Code No.

No. 2 992671

No. 3 992672

CHARGER

Model UC14YFA

Charging time EB9B, EB1220BL: Approx. 50 min. (at 20°C)

EB926H, EB1226HL: Approx. 65 min. (at 20°C)

EB930H, EB1230HL: Approx. 70 min. (at 20°C)

Charging voltage 7.2 – 14.4 V

Weight 0.6 kg

Model WR9DM2 (9.6 V) WR12DM2 (12 V)

No-load speed 0 – 2600 min

–1

Capacity M6 – M14 (Ordinary bolt) M6 – M16 (Ordinary bolt)

M6 – M10 (High tension bolt) M6 – M12 (High tension bolt)

Tightening torque

Rechargeable battery EB9B: Ni-Cd battery, 9.6 V EB1220BL: Ni-Cd battery, 12 V

(2.0 Ah 8 cells) (2.0 Ah 10 cells)

EB930H: Ni-MH battery, 9.6 V EB1230HL: Ni-MH battery, 12 V

(3.0 Ah 8 cells) (3.0 Ah 10 cells)

Weight 1.4 kg 1.6 kg

Maximum 120 N·m

{1220 kgf·cm}

Tightening is M12 high tension bolt

(strength grade 12.9), when fully

charged at 20°C temp.

Tightnening time: 3 sec.

Maximum 165 N·m

{1685 kgf·cm}

Tightening is M16 (F10T), when fully

charged at 20°C temp.

Tightening time: 3 sec.

Cordless Impact Wrench

Part Name

Engraved

LBCode No.

characters

10 mm Hexagonal socket

14 65 14 996180

(small type)

10 mm Hexagonal socket 16 65 16 996181

10 mm Hexagonal socket 17 65 17 996182

1/2" Hexagonal long

socket

21 166 21 996197

Engraved characters

STANDARD ACCESSORIES

1. Charger (UC14YFA) ................................................... 1

2. Plastic case ................................................................ 1

Standard accessories are subject to change without

notice.

OPTIONAL ACCESSORIES

(Sold separately)

1. Plus driver bit

2. Hexagonal socket

3. Wood working drill: Code No. 959183

4. Drill chuck adapter set: Code No. 321823

Use the drills available on the local market.

English

9

1. Sockets

Form B Form C

Form D

Code No.

High ISO ISO Inch

Form

tension

(ordinary)

(small) bolts L L1 øF

10 mm 944291 M6 10 B 40 8 18

12 mm 873632 M8 W5/16" 12 B 40 8 20

13 mm 873539 M8 13 B 40 9 25

12.7

Hexagonal

14 mm 873540 M10 14 B 40 9 25

Socket

17 mm 873536 M10 M12 W3/8" 17 C 32 8 28

19 mm 873624 M12 M14 W7/16" 19 C 34 9 28

21 mm 873626 W1/2" 21 D 36 10 32

22 mm 873627 M12 M14 M16 22 D 40 14 35

24 mm 873629 M16 M18 24 D 40 15 38

Square

head drive

dimensions

S (mm)

Part Name

Suitable Bolt Diameter

Hexagonal

width across

flats H (mm)

Main Socket

Dimensions (mm)

Form B Form C

Form D

2. Long Socket

Table 1

H S

L

L1

ØF

H S

L

L1

ØF

H S

L

L1

ØF

H

S

L1

L2

L

ØF

H S

L1

L2

L

ØF

H

S

L1

L2

L

ØF

<For WR9DM2> Table 2

Code No.

ISO ISO Inch

Form

(ordinary)

(small) bolts L L1 øF

8 mm 996125 M5 8 B 33 5 13

10 mm 996126 M6 10 B 33 6 16

12 mm 996127 M8 W5/16" 12 C 33 7 19

9.5

13 mm 996128 M8 13 B 33 8 20

14 mm 996129 M10 14 B 33 8 21

16 mm 996130 M10 16 D 33 9 24

17 mm 996131 M10 M12 W3/8" 17 D 33 10 25

18 mm 996132 M12 18 D 33 10 26

19 mm 996133 M12 W7/16" 19 D 33 12 27.5

Square

head drive

dimensions

S (mm)

Part Name

Suitable Bolt Diameter

Hexagonal

width across

flats H (mm)

Main Socket

Dimensions (mm)

Hexagonal

Socket

English

10

Table 3

Code No.

High ISO ISO Inch

Form

tension

(ordinary)

(small) bolts L L1 L2 øF

12 mm 955138 M8 W5/16" 12 B 52 20 34 20

13 mm 955139 M8 13 B 52 20 34 21.5

14 mm 955140 M10 14 B 52 20 34 22

17 mm 955141 M10 M12 W3/8" 17 B 52 24 34 25

17 mm 955149 M10 M12 W3/8" 17 B 75 24 57 25

12.7

Long

19 mm 955142 M12 M14 W7/16" 19 B 52 24 34 28

Socket

19 mm 955150 M12 M14 W7/16" 19 B 75 24 57 28

21 mm 955143 W1/2" 21 D 52 24 34 31

21 mm 955151 W1/2" 21 D 75 24 57 31

21 mm 991480 W1/2" 21 D 125 24 107 31

22 mm 955144 M12 M14 M16 22 D 52 24 34 32.5

24 mm 955146 M16 M18 24 D 52 25 34 34

Square

head drive

dimensions

S (mm)

Part Name

Suitable Bolt Diameter

Hexagonal

width across

flats H (mm)

Main Socket

Dimensions (mm)

<For WR9DM2> Table 4

Code No.

ISO ISO Inch

Form

(ordinary)

(small) bolts L L1 L2 øF

8 mm 996134 M5 8 B 60 12 48 13

10 mm 996135 M6 10 B 60 12 48 16

12 mm 996136 M8 W5/16" 12 C 60 14 48 18.4

9.5

13 mm 996137 M8 13 B 60 14 48 18.9

14 mm 996138 M10 14 B 60 15 48 19.5

16 mm 996139 M10 16 D 60 15 48 24

17 mm 996140 M10 M12 W3/8" 17 D 60 15 48 25

18 mm 996141 M12 18 D 60 16 48 26

19 mm 996142 M12 W7/16" 19 D 60 17 48 27.5

Square

head drive

dimensions

S (mm)

Part Name

Suitable Bolt Diameter

Hexagonal

width across

flats H (mm)

Main Socket

Dimensions (mm)

Long

Socket

3. Extension bar: WR12DM2: Code No. 873633

WR9DM2: Code No. 996143

The extension bar is convenient for working in very

restricted spaces or when the socket provided cannot

reach the bolt to be tightened.

CAUTION:

When the extension bar is used, the tightening torque

is reduced slightly compared with the ordinary socket.

4. Universal joint: WR12DM2: Code No. 992610

WR9DM2: Code No. 996147

The universal joint is convenient for impacting nuts

when there is an angle between the socket and

wrench, or when working in a very narrow space.

5. Duct Socket: (WR12DM2)

This is used for tightening bolts and nuts on flange

sections of air conditioners, type ducts, etc.

6. Corner attachment (Model EW-14R) (WR12DM2)

Use this attachment only when the machine is applied

to the nut or bolt at the right angle.

Code No.

Hexagonal width

across flats (mm)

993658 12

992613 13

992615 14

English

11

7. Bit adaptor: Code No. 322752 (WR12DM2)

This is used for tightening small screws (M6 – M8).

NOTE:

(1) This adaptor is set only on the anvil (drive angle) of

the main unit. The bit adapter cannot be attached to

the special accessory anvil (square drive).

(2) Before starting work with the adapter, tighten a few

screws with it to make sure it’s tightening with the

appropriate torque.

(3) Tightening speed will be greatly reduced when driving

wood, tapping or other similar screws.

Optional accessories are subject to change without notice.

APPLICATION

< WH12DM2, WH9DM2, WH12DMR >

䡬 Driving and removing of small screws, small bolts,

etc.

< WR12DM2, WR9DM2 >

䡬 Tightening and loosening of all types of bolts and

nuts, used for securing structural items

BATTERY REMOVAL/INSTALLATION

1. Battery removal

Hold the handle tightly and push the battery latch to

remove the battery. (See Fig. 1 and 2)

CAUTION:

Never short-circuit the battery.

2. Battery installation

Insert the battery while observing its polarities. (See

Fig. 2)

CHARGING

Before using the impact driver, charge the battery as

follows.

1. Connect the charger’s power cord to a receptacle.

When the power cord is connected, the charger’s

pilot lamp will blink in red. (At 1-second intervals.)

2. Insert the battery into the charger.

Insert the battery firmly, in the direction shown in

Fig. 3, until it contacts the bottom of the charger

compartment.

CAUTION:

䡬 If the battery is inserted in the reverse direction, not

only recharging will become impossible, but it may

also cause problems in the charger such as deformed

recharging terminal.

3. Charging

When inserting a battery in the charger, charging will

commence and the pilot lamp will light up

continuously in red.

When the battery becomes fully recharged, the pilot

lamp will blink in red. (At 1-second intervals.) (See

Table 5)

(1) Pilot lamp indication

The indications of the pilot lamp will be as shown in

Table 5, according to the condition of the charger or

the rechargeable battery.

Lights for 0.5 seconds. Does not light for

0.5 seconds. (off for 0.5 seconds)

Lights continuously

Lights for 0.5 seconds. Does not light for

0.5 seconds. (off for 0.5 seconds)

Lights for 0.1 seconds. Does not light for

0.1 seconds. (off for 0.1 seconds)

Lights continuously

Before

charging

While

charging

Charging

complete

Charging

impossible

Charging

impossible

Blinks

(RED)

Lights

(RED)

Blinks

(RED)

Flikers

(RED)

Lights

(GREEN)

Malfunction in the battery

or the charger

The battery temperature

is high, making

recharging impossible.

Table 5

Indications of the lamps

English

12

(2) Regarding the temperatures of the rechargeable battery

The temperatures for rechargeable batteries are as

shown in the table below, and batteries that have

become hot should be cooled for a while before

being recharged.

Table 6 Recharging ranges of batteries

(3) Regarding recharging time

Depending on the combination of the charger and

batteries, the charging time will become as shown in

Table 7.

Table 7 Charging time (At 20°C)

NOTE:

The charging time may vary according to the ambient

temperature and power source voltage.

4. Disconnect the charger’s power cord from the receptacle.

5. Hold the charger firmly and pull out the battery.

NOTE:

Be sure to pull out the battery from the charger after

use, and then keep it.

Regarding electric discharge in case of new

batteries, etc.

As the internal chemical substance of new batteries

and batteries that have not been used for an extended

period is not activated, the electric discharge might

be low when using them the first and second time.

This is a temporary phenomenon, and normal time

required for recharging will be restored by recharging

the batteries 2 – 3 times.

How to make the batteries perform longer

(1) Recharge the batteries before they become completely

exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery.

If you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the battery

and recharge it after it has cooled for a while.

CAUTION:

䡬 If the battery is charged while it is heated because it

has been left for a long time in a location subject to

direct sunlight or because the battery has just been

Temperatures at

Rechargeable batteries which the battery

can be recharged

EB1220BL, EB9B –5°C – 60°C

EB1226HL, EB1230HL, EB926H, EB930H

0°C – 45°C

used, the pilot lamp of the charger lights up green. In

such a case, first let the battery cool, then start

charging.

䡬 When the pilot lamp flikers in red quickly (at 0.2-

second intervals), check for and take out any foreign

objects in the charger’s battery installation hole. If

there are no foreign objects, it is probable that the

battery or charger is malfunctioning. Take it to your

Authorized Service Center.

䡬 Since the built-in micro computer takes about 3

seconds to confirm that the battery being charged

with UC14YFA is taken out, wait for a minimum of 3

seconds before reinserting it to continue charging. If

the battery is reinserted within 3 seconds, the battery

may not be properly charged.

PRIOR TO OPERATION

1. Preparing and checking the work environment

Make sure that the work site meets all the conditions

laid forth in the precautions.

2. Checking the battery

Make sure that the battery is installed firmly. If it is at

all loose it could come off and cause an accident.

3. Installing the bit (WH12DM2, WH9DM2, WH12DMR)

Always follow the following procedure to install driver

bit. (Fig. 4)

(1) Pull the guide sleeve away from front of the tool.

(2) Insert the bit into the hexagonal hole in the anvil.

(3) Release the guide sleeve and it returns to its original

position.

CAUTION:

If the guide sleeve does not return to its original

position, then the bit is not installed properly.

4. Selecting the socket matched to the bolt

(WR12DM2, WR9DM2)

Be sure to use a socket which is matched to the bolt

to be tightened. Using an improper socket will not

only result in insufficient tightening but also in

damage to the socket or nut.

A worn or deformed hex. or square-holed socket will

not give an adequate tightness for fitting to the nut or

anvil, consequently resulting in loss of tightening

torque.

Pay attention to wear of socket hole, and replace

before further wear has developed.

Finally, install the socket prescribed in Item 5. The

section on “Optional Accessories” details the

relationship between bolt sizes and sockets. Sockets

are named according to the dihedral width of the

hexagonal hole.

5. Installing a socket (WR12DM2, WR9DM2)

Select the socket to be used.

䢇 Pin, O-ring type (Fig. 5 and 6)

(1) Align the hole in the socket with the hole in the anvil

and insert the anvil into the socket.

(2) Insert the pin into the socket.

(3) Attach the ring to the groove on the socket.

䢇 Plunger type (Fig. 7)

Align the plunger located in the square part of the

anvil with the hole in the hex. socket. Then push the

plunger, and mount the hex. socket on the anvil.

Check that the plunger is fully engaged in the hole.

When removing the socket, reverse the sequence.

Charger

UC14YFA

Battery

EB1220BL, EB9B

Approx. 50 min.

EB1226HL, EB926H

Approx. 65 min.

EB1230HL, EB930H

Approx. 70 min.

English

13

䢇 Retaining ring type (Fig. 8)

(1) Align the square portions of the socket and the anvil

with each other.

(2) Make sure to firmly install the socket by pushing it all

the way into the anvil.

(3) When removing the socket, pull it out of the anvil.

CAUTION:

䡬 Please use the designated attachments which are

listed in the operations manual and Hitachi’s catalog.

Accidents or injuries could result from not doing so.

䡬 Make sure to firmly install the socket in the anvil. If

the socket is not firmly installed it might come out

and cause injuries.

HOW TO USE

CAUTION:

䡬 When using the light equipped hook, pay sufficient

attention so that the main equipment does not fall. If

the tool falls, there is a risk of accident.

䡬 Do not attach the tip tool except phillips bit to the tool

main unit when carrying the tool main unit with the

light equipped hook suspended from a waist belt.

Injury may result if you carry the equipment

suspended from the waist belt with sharp tipped

components such as drill bit attached.

1. Using the light equipped hook

The light equipped hook can be installed on the right

or left side and the angle can be adjusted in 5 steps

between 0° and 80°.

(1) Operating the hook

(a) Pull out the hook toward you in the direction of

arrow (A) and turn in the direction of arrow (B).

(Fig. 9)

(b) The angle can be adjusted in 5 steps (0°, 20°, 40°,

60°, 80°).

Adjust the angle of the hook to the desired position

for use.

(2) Switching the hook position

CAUTION:

Incomplete installation of the hook may result in

bodily injury when used.

(a) Securely hold the main unit and remove the screw

using a slotted head screwdriver or a coin. (Fig.

10)

(b) Remove the hook and spring. (Fig. 11)

(c) Install the hook and spring on the other side and

securely fasten with screw. (Fig. 12)

NOTE:

Pay attention to the spring orientation. Install the

spring with larger diameter away from you. (Fig. 12)

(3) Using as an auxiliary light

(a) Press the switch to turn off the light.

If forgotten, the light will turn off automatically

after 15 minutes.

(b) The direction of the light can be adjusted within

the range of hook positions 1 - 5. (Fig. 13)

䡬 Lighting time

AAAA manganese batteries: approx. 15 hrs.

AAAA alkali batteries: approx. 30 hrs.

CAUTION:

Do not look directly into the light.

Such actions could result in eye injury.

(4) Replacing the batteries

(a) Loosen the hook screw with a phillips-head

screwdriver (No. 1). (Fig. 14)

Remove the hook cover by pushing in the direction

of the arrow. (Fig. 15)

(b) Remove the old batteries and insert the new

batteries. Align with the hook indications and

position the plus (+) and minus (–) terminals

correctly. (Fig. 16)

(c) Align the indentation in the hook main body with

the protuberance of the hook cover, press the

hook cover in the direction opposite to that of the

arrow shown in Fig. 15 and then tighten the screw.

Use commercially available AAAA batteries

(1.5 V).

NOTE:

Do not tighten the screw excessively. Such action

could strip the screw threads.

CAUTION:

䡬 Failure to observe the following can result in battery

leakage, rust or malfunction.

Position the plus (+) and minus (–) terminals correctly.

Replace both batteries at the same time. Do not mix

old and new batteries.

Remove exhausted batteries from the hook

immediately.

䡬 Do not discard batteries together with normal trash

and do not throw batteries into fire.

䡬 Store batteries out of the reach of children.

䡬 Use batteries correctly in accordance with the battery

specifications and indications.

2. Check the rotational direction

The bit rotates clockwise (viewed from the rear side)

by pushing the R-side of the push button.

The L-side of the push button is pushed to turn the bit

counterclockwise. (See Fig. 17) (The

L

and

R

marks

are provided on the body.)

CAUTION:

The push button cannot be switched while the impact

driver is turning. To switch the push button, stop the

impact driver, then set the push button.

3. Switch operation

䡬 When the trigger switch is depressed, the tool rotates.

When the trigger is released, the tool stops.

䡬 The rotational speed can be controlled by varying the

amount that the trigger switch is pulled. Speed is low

when the trigger switch is pulled slightly and increases

as the trigger switch is pulled more.

4. Tightening and loosening screws (WH12DM2,

WH9DM2, WH12DMR)

Install the bit that matches the screw, line up the bit

in the grooves of the head of the screw, then tighten

it.

Push the impact driver just enough to keep the bit

fitting the head of the screw.

CAUTION:

Applying the impact driver for too long tightens the

screw too much and can break it.

Tightening a screw with the impact driver at an angle

to that screw can damage the head of the screw and

the proper force will not be transmitted to the screw.

Tighten with this impact driver lined up straight with

the screw.

English

14

5. Number of screws tightenings possible (WH12DM2,

WH9DM2, WH12DMR)

Please refer to the table below for the number of

screw tightened possible with one charge.

WH12DM2, WH12DMR (EB1230HL)

WH9DM2 (EB930H)

These values may vary slightly, according to

surrounding temperature and battery characteristics.

6. Number of bolt tightened possible (WR12DM2,

WR9DM2)

Please refer to the table below for the number of bolt

tightened possible with one charge.

WR12DM2 (EB1230HL)

WR9DM2 (EB930H)

These values may vary slightly, according to

surrounding temperature and battery characteristics.

NOTE:

The use of the battery EB1230HL, EB930H in a cold

condition (below 0 degree Centigrade) can sometimes

result in the weakened tightening torque and reduced

amount of work. This, however, is a temporary

phenomenon, and returns to normal when the battery

warms up.

OPERATIONAL CAUTIONS

1. Resting the unit after continuous work

After use for continuous bolt-tightening work, rest

the unit for 15 minutes or so when replacing the

battery. The temperature of the motor, switch, etc.,

will rise if the work is started again immediately after

battery replacement, eventually resulting in burnout.

NOTE:

Do not touch the protector, as it gets very hot during

continuous work.

2. Cautions on use of the speed control switch

This switch has a built-in, electronic circuit which

steplessly varies the rotation speed. Consequently,

when the switch trigger is pulled only slightly (low

speed rotation) and the motor is stopped while

continuously driving in screws, the components of

Screw used No. of tightenings

Wood screw ø4 × 50

Approx. 530

(Soft wood)

Machine screw M8 × 16 Approx. 1690

Bolt used No. of tightenings

M12 Hightension bolt Approx. 180

Bolt used No. of tightenings

M12 Hightension bolt Approx. 120

the electronic circuit parts may overheat and be

damaged.

3. Tightening torque

Refer to Fig. 22, 23, 24, 25 and Fig. 26 for the tightening

torque of bolts (according to size), under the

conditions shown in Fig. 27. Please use this example

as a general reference, as tightening torque will vary

according to tightening conditions.

NOTE:

䡬 If a long striking time is used, screws will be strongly

tightened. This may cause the screw to break, or may

damage the tip of the bit.

䡬 If the unit is held at an angle to the screw being

tightened, the head of the screw may be damaged, or

the specified torque may not be transmitted to the

screw. Always keep the unit and the screw being

tightened in a straight line.

4. Use a tightening time suitable for the screw

The appropriate torque for a screw differs according

to the material and size of the screw, and the material

being screwed etc., so please use a tightening time

suitable for the screw. In particular, if a long tightening

time is used in the case of screws smaller than M8,

there is a danger of the screw breaking, so please

confirm the tightening time and the tightening torque

beforehand.

5. Work at a tightening torque suitable for the bolt

under impact

The optimum tightening torque for nuts or bolts differs

with material and size of the nuts or bolts. An

excessively large tightening torque for a small bolt

may stretch or break the bolt. The tightening torque

increases in proportion to the operaton time. Use the

correct operating time for the bolt.

6. Holding the tool

Hold the impact wrench firmly with both hands. In

this case hold the wrench in line with the bolt.

It is not necessary to push the wrench very hard.

Hold the wrench with a force just sufficient to

counteract the impact force.

7. Confirm the tightening torque

The following factors contribute to a reduction of the

tightening torque. So confirm the actual tightening

torque needed by screwing up some bolts before the

job with a hand torque wrench. Factors affecting the

tightening torque are as follows.

(1) Voltage

When the discharge margin is reached, voltage

decreases and tightening torque is lowered.

(2) Operating time

The tightening torque increases when the operating

time increases. But the tightening torque does not

increase above a certain value even if the tool is

driven for a long time. (See Fig. 22, 23, 24, 25 and 26)

(3) Diameter of bolt

The tightening torque differs with the diameter of the

bolt as shown in Fig. 22, 23, 24, 25 and 26. Generally a

larger diameter bolt requires larger tightening torque.

(4) Tightening conditions

The tightening torque differs according to the torque

ratio; class, and length of bolts even when bolts with

the same size threads are used. The tightening torque

also differs according to the condition of the surface

of workpiece through which the bolts are to be

tightened. When the bolt and nut turn together, torque

is greatly reduced.

Screw used

No. of tightenings

WH12DM2 WH12DMR

Wood screw ø4 × 50

Approx. 790 Approx. 750

(Soft wood)

Machine screw M8 × 16

Approx. 1750 Approx. 1660

English

15

M12 × 45

kgf·cm

1200

1000

800

600

400

200

0

N·m

120

100

80

60

40

20

0

0 1 2 3

M10 × 30

kgf·cm

1000

800

600

400

200

0

N·m

100

80

60

40

20

0

1 2 3

M8 × 30

kgf·cm

1000

800

600

400

200

0

N·m

100

80

60

40

20

0

1 2 3

Tightening torque

Tightening time: sec.

(Steel plate thickness

t = 10 mm)

Tightening time: sec.

(Steel plate thickness

t = 25 mm)

Tightening time: sec.

(Steel plate thickness

t = 25 mm)

1400

1200

1000

800

600

400

200

0

140

120

100

80

60

40

20

0

M14 × 50

0 123

kgf·cm N·m

1400

1200

1000

800

600

400

200

0

140

120

100

80

60

40

20

0

M12 × 45

0 123

kgf·cm N·m

1000

800

600

400

200

0

0 123

100

80

60

40

20

0

M10 × 30

kgf·cm N·m

Ordinary bolt

High tension bolt

Ordinary bolt

High tension bolt

Ordinary bolt

Fig. 22

For WH12DM2

(5) Using optional parts (WR12DM2, WR9DM2)

The tightening torque is reduced a little when an

extension bar, universal joint or a long socket is

used.

(6) Clearance of the socket (WR12DM2, WR9DM2)

A worn or deformed hex. or a square-holed socket

will not give an adequate tightness to the fitting

between the nut or anvil, consequently resulting in

loss of tightening torque.

Using an improper socket which does not match to

the bolt will result in an insufficient tightening torque.

Matching socket and bolt sizes are shown in Table 1,

2, 3 and 4.

(7) Tightening torque varies, depending on the battery’s

charge level. (WR12DM2, WR9DM2)

Fig. 28 and 29 show examples of the relationship

between tightening torque and the number of

tightenings, for WR12DM2 and WR9DM2. As shown,

tightening torque gradually weakens with the increase

in the number of tightenings. In particular, as the

torque decreases very close to the complete discharge

(“a” margin in graph), the unit’s impact weakens, the

number of time impacts declines and tightening

torque drops off abruptly. If this occurs, check torque

level, then recharge the battery if necessary.

For WH9DM2

Tightening time: sec.

(Steel plate thickness

t = 10 mm)

Tightening time: sec.

(Steel plate thickness

t = 25 mm)

Tightening time: sec.

(Steel plate thickness

t = 25 mm)

Tightening torque

High tension bolt

Fig. 23

High tension bolt

Ordinary bolt

English

16

M12 × 45

kgf·cm

1400

1200

1000

800

600

400

200

0

N·m

140

120

100

80

60

40

20

0

0 1 2 3

M10 × 30

kgf·cm

1000

800

600

400

200

0

N·m

100

80

60

40

20

0

0 1 2 3

M8 × 30

kgf·cm

1000

800

600

400

200

0

N·m

100

80

60

40

20

0

0 1 2 3

Tightening time: sec.

(Steel plate thickness

t = 10 mm)

Tightening time: sec.

(Steel plate thickness

t = 25 mm)

Tightening time: sec.

(Steel plate thickness

t = 25 mm)

Tightening torque

Fig. 25

2000

1500

1000

500

0

0123

200

150

100

50

0

M10 × 30

kgf·cm N·m

2000

1500

1000

500

0

0123

200

150

100

50

0

M12 × 45

kgf·cm N·m

2000

1500

1000

500

0

0123

200

150

100

50

0

M14 × 50

kgf·cm N·m

Ordinary bolt

High tension

bolt

High tension

bolt

Ordinary bolt

High tension

bolt

For WR12DM2

Ordinary bolt

For WR9DM2

Tightening torque

Ordinary bolt

High tension

bolt

High tension

bolt

High tension

bolt

Tightening torque

Tightening time: sec.

(Steel plate thickness

t = 10 mm)

Tightening time: sec.

(Steel plate thickness

t = 25 mm)

Tightening time: sec.

(Steel plate thickness

t = 25 mm)

1400

1200

1000

800

600

400

200

0

140

120

100

80

60

40

20

0

M14 × 50

0 123

kgf·cm N·m

1400

1200

1000

800

600

400

200

0

140

120

100

80

60

40

20

0

M12 × 45

0 123

kgf·cm N·m

1000

800

600

400

200

0

0 123

100

80

60

40

20

0

M10 × 30

kgf·cm N·m

Ordinary bolt

High tension bolt

Ordinary bolt

Fig. 24

High tension bolt

For WH12DMR

Tightening time: sec.

(Steel plate thickness

t = 10 mm)

Tightening time: sec.

(Steel plate thickness

t = 10 mm)

Tightening time: sec.

(Steel plate thickness

t = 25 mm)

Fig. 26

English

17

kgf·cm

1600

1200

800

400

0

0 20 40

60

80 100 120 140 160

N·m

160

120

80

40

0

a

Tightening torque

M16 × 55 F10T (tighening time 3 sec)

2000

1600

1200

800

400

0

020406080100 120 140

200

160

120

80

40

0

a

kgf·cm N·m

When full recharged

When completely

discharged

Number of tightenings (PCS)/charging

Fig. 28

For WR12DM2

For WR9DM2

Fig. 29

Tightening torque

Number of tightenings (PCS)/charging

When full recharged

When completely

discharged

M14 × 50 High tension bolt

(tighening time 3 sec)

MAINTENANCE AND INSPECTION

1. Inspecting the driver bit (WH12DM2, WH9DM2,

WH12DMR)

Using a broken bit or one with a worn out tip is

dangerous because the bit can slip. Replace it.

2. Inspecting the socket (WR12DM2, WR9DM2)

A worn or deformed hex. or a square-holed socket

will not give an adequate tightness to the fitting

between the nut or anvil, consequently resulting in

loss of tightening torque. Pay attention to wear of a

socket holes periodically, and replace with a new one

if needed.

3. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure

that they are properly tightened. Should any of the

screws be loose, retighten them immediately. Failure

to do so may result in serious hazard.

4. Maintenance of the motor

The motor unit winding is the very “heart” of the

power tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

Nut

Fig. 27

Explanation of strength grade:

4 — Yield point of bolt: 32 kgf/mm

2

8 — Pulling strength of bolt: 40 kgf/mm

2

*The following bolt is used.

Ordinary bolt: Strength grade 4.8

High tensile bolt: Strength grade 12.9

)(

Bolt

Steel plate thickness t

English

18

5. Inspecting the carbon brushes (Fig. 18)

The motor employs carbon brushes which are

consumable parts. Since and excessively worn carbon

brush can result in motor trouble, replace the carbon

brush with new ones when it becomes worn to or

near the “wear limit”. In addition, always keep carbon

brushes clean and ensure that they slide freely whthin

the brush holders.

NOTE:

When replacing the carbon brush with a new one, be

sure to use the Hitachi Carbon Brush Code No. 999054.

6. Replacing carbon brushes

Take out the carbon brush by first removing the

brush cap and then hooking the protrusion of the

carbon brush with a slotted head screw driver, etc.,

as shown in Fig. 20.

When installing the carbon brush, choose the direction

so that the nail of the carbon brush agrees with the

contact portion outside the brush tube. Then push it

in with a finger as illustrated in Fig. 21. Lastly, install

the brush cap.

CAUTION:

Be absolutely sure to insert the nail of the carbon

brush into the contact portion outside the brush tube.

(You can insert whichever one of the two nails

provided.)

Caution must be exercised since any error in this

operation can result in the deformed nail of the carbon

brush and may cause motor trouble at an early stage.

7 Cleaning of the outside

When the impact driver is stained, wipe with a soft

dry cloth or a cloth moistened with soapy water. Do

not use chloric solvents, gasoline or paint thinner, as

they melt plastics.

8. Storage

Store the impact driver in a place in which the

temperature is less than 40°C, and out of reach of

children.

9. Service parts list

A:Item No.

B:Code No.

C:No. Used

D:Remarks

CAUTION:

Repair, modification and inspection of Hitachi Power

Tools must be carried out by an Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

MODIFICATIONS:

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts (i.e. code numbers and/or

design) may be changed without prior notice.

NOTE:

Due to HITACHI’s continuing program of reserch and

development, the specifications herein are subject to

change without prior notice.

IMPORTANT:

Correct connection of the plug

The wires of the mains lead are coloured in accordance

with the following code:

Blue: –Neutral

Brown: –Live

As the colours of the wires in the mains lead of this tool

may not correspond with the coloured markings

identifying the terminals in your plug proceed as follows:

The wire coloured blue must be connected to the terminal

marked with the letter N or coloured black.

The wire coloured brown must be connected to the

terminal marked with the letter L or coloured red.

Neither core must be connected to the earth terminal.

NOTE:

This requirement is provided according to BRITISH

STANDARD 2769: 1984.

Therefore, the letter code and colour code may not be

applicable to other markets except United Kingdom.

Information concerning airborne noise and vibration

The measured values were determined according to

EN50144.

The typical A-weighted sound pressure level:

95 dB (A)(WH12DM2, WH12DMR)

95 dB (A)(WH9DM2)

96 dB (A)(WR12DM2)

96 dB (A)(WR9DM2)

The typical A-weighted sound power level:

108 dB (A)(WH12DM2, WH12DMR)

108 dB (A)(WH9DM2)

109 dB (A)(WR12DM2)

109 dB (A)(WR9DM2)

Wear ear protection.

The typical weighted root mean square acceleration

value: 10.8 m/s

2

(WH12DM2, WH12DMR)

9.7 m/s

2

(WH9DM2)

12.1 m/s

2

(WR12DM2)

10.9 m/s

2

(WR9DM2)

Deutsch

19

VORSICHT FÜR ALLGEMEINE BEDIENUNG

1. Den Arbeitsplatz stets sauber halten. Unaufger-

äumte Arbeitsplätze und Werkbänke erhöhen die

Unfallgefahr.

2. Gefährliche Umgebungen vermeiden. Die Maschine

und das Ladegerät keiner Feuchtigkeit aussetzen

oder an nassen Stellen benutzen. Achten Sie auf

einen hellen, wenn erforderlich gut beleuchteten

Arbeitsplatz. Maschine und Ladegerät niemals in

der Nähe von brennbaren oder explosiven

Materialien, Flüssigkeiten oder Gasen verwenden.

3. Das Gerät ist nicht für Verwendung durch Kinder

oder gebrechliche Personen ohne Aufsicht gedacht.

Kinder sollten beaufsichtigt werden, um

sicherzustellen, dass sie nicht mit dem Gerät spielen.

Alle Besucher sollten in sicherer Entfernung vom

Arbeitsbereich gehalten werden.

4. Unbenutztes Werkzeug und Ladegerät an einen

trockenen und verschlossenen Ort wegräumen;

außerhalb der Reichweite von Kindern und

gebrechlichen Personen aufbewahren. Die

Temperatur sollte weniger als 40°C betragen.

5. Das Werkzeug nicht überlasten. Es arbeitet sich

besser und sicherer bei angemessenen Gesch-

windigkeiten und Belastungen.

6. Das richtige Werkzeug zur Arbeit verwenden.

Erwarten Sie nicht, daß ein zu kleines Werkzeug

oder Zubehör die Arbeit einer Hochleistung-

smaschine verrichtet.

7. Achten Sie auf die richtige Kleidung. Lose oder zu

weite Kleidung bzw. und/oder Schmuck (z.B. Ketten,

Ringe, usw.) könnten sich in rotierenden oder

bewegenden Teilen verfangen. Schutzhand-schuhe

und Arbeitsschutzschuhe sind bei denArbeiten zu

tragen.

8. Vergessen Sie nicht bei Arbeiten mit Werkzeugen

eine Sicherheitsbrille zu tragen, ebenfalls, wenn

erforderlich eine Gesichts-oder Staubmaske.

9. Schonen Sie das Anschlußkabel. Tragen Sie niemals

das Ladegerät am Kabel und ziehen Sie nicht daran,

um den Stecker von der Steckdose zu trennen. Das

Kabel gegen übermäßige Hitze, Öl und scharfe

Kanten schützen.

10. Das zu bearbeitende Werkstück gut sichern. Zwingen

oder Schraubstock für die Befestigung des

Werkstücks benutzen. Es erhöht die Sicherheit und

schafft freie Hände zur Bedienung des Werkzeugs.

11. Verschaffen Sie sich einen festen Stand, er garantiert

Sicherheit und optimales Gleichgewicht bei der

Arbeit.

12. Das Werkzeug in gutem Zustand behalten. Stets

sauber halten, pflegen und warten, damit es immer

die beste Leistung bringt. Beachten Sie die

Anweisungen für Schmieren oder eventuelle

Auswechselungen.

13. Wird das Ladegerät nicht benutzt oder einer Prüfung

unterzogen, entfernen Sie den Stecker aus Ihrem

Wechselstro-manschluß.

14. Entfernen Sie Futterschlüssel und

Schraubenschlüssel. Machen Sie es sich zur

Gewohnheit, vor dem Einschalten des Werkzeugs

sicherzustellen, dass Schlüssel abgezogen worden

sind.

15. Zufälliges Einschalten vermeiden. Das Werkzeug

nicht mit dem Finger am Schalter tragen.

16. Um Gefahren zu vermeiden, verwenden Sie nur

das vorgeschriebene Ladegerät.

17. Nur Original-HITACHI-Ersatzteile verwenden.

18. Das Werkzeug und Ladegerät nicht anders als in

der Gebrauchsanweisung vorgeschrieben

verwenden.

19. Die Benutzung von Zubehör und Sonderzubehör,

die nicht im HITACHI-Katalog oder in der

Bedienungsanleitung aufgeführt sind, erhöhen das

Risiko von Verletzungen.

20. Reparaturen sollten nur in autorisierten HITACHI-

Service-Werkstätten durchgeführt werden. Der

Hersteller haftet nicht für Schäden und Unfälle, die

auf unautorisierte Fachkräfte oder auf den

Mißbrauch des Werkzeugs zurückgeführt werden

können.

21. Um den ursprünglichen Zustand des Werkzeugs

und Ladegerätes zu erhalten, entfernen Sie keine

Hinweisschilder, Abdeckungen oder Schrauben.

22. Nehmen Sie das Ladegerät immer nur mit der auf

dem Typenschild vorgeschriebenen Spannung in

Gebrauch.

23. Bewegliche Teile und Zubehöre nicht berühren,

wenn das Werkzeug nicht vom Netz abgetrennt ist.

24. Immer vor der Benutzung die Batterie aufladen.

25. Nur die vorgeschriebene Batterie verwenden. Keine

gewöhnlichen Trockenbatterien oder Auto-

Batterien, für das Elektro-Werkzeug verwenden.

26. Keinen Transformator mit Puffersatz verwenden.

27. Die Batterie nicht an einem elektrischen Generator

oder einer Gleichstromversorgung aufladen.

28. Die Batterie immer drinnen aufladen. Da sich beim

Laden Ladegerät und Batterie erwärmen, an einem

Ort aufladen, der nicht direkter Sonnenbestrahlung

ausgesetzt und trocken ist.

29. Wenn an hochliegenden Stellen gearbeitet wird,

vergewissern Sie sich vor Arbeitsbeginn, daß sich

under Ihnen keiner im Arbeits-bzw. Gefahrenkreis

aufhält.

30. Die detaillierte Bestandsteilzeichnung, die der

Bedienungsanleitung beigefügt ist, ist nur für die

autorisierte Service-Werkstätte bestimmt.

31. Falls das mitgelieferte Kabel beschädigt wird, muss

es durch den Hersteller, seinen

Kundendienstvertreter oder eine ähnlich qualifizierte

Person ausgewechselt werden, um Gefahren zu

vermeiden.

VORSICHTSMASSNAHMEN FÜR DEN AKKU-

SCHLAGSCHRAUBER

1. Dies ist ein tragbares Werkzeuggerät zum Anziehen

und Lösen von Schrauben. Es sollte nur für diesen

Zweck eingesetzt werden.

2. Bei längerem Arbeiten Ohrstöpsel verwenden.

3. Es ist äußerst gefährlich, das Gerät nur mit einer

Hand zu bedienen. Das Gerät ist beim Betrieb mit

beiden Händen festzuhalten.

4. Nachdem das Schraubstück angebracht wurde,

sollte ein wenig daran gezogen werden, um

sicherzugehen, daß es festsitzt. Wenn das

Schraubstück nicht richtig aufgesetzt wird, kann es

sich während des Betriebs lösen, was

Verletzungsgefahr bedeutet.

5 Das Schrubstück gemäß der anzuziehenden

Schraube verwenden.

6. Sollte versucht werden, mit dem Schlag-Schrauber

eine Schraube anzuziehen, wenn sich der Schlag-

Schrauber in einem Winkel zur Schraube befindet,

kann die Preßkraft des Geräts nicht voll zur Geltung

kommen; außer dem kann der Schraubenkopf

beschädigt werden. Anziehen, wenn sich der Schlag-

Schrauber mit der Schraube auf einer Linie befindet.

7. Die Batterie immer bei einer Temperatur von 0 –

40°C laden.

La pagina sta caricando ...

Hitachi WR 12DM2 Handling Instructions Manual

Questo manuale è adatto anche per

Hitachi WR 12DM2 Handling Instructions Manual

in altre lingue

Documenti correlati

Altri documenti