Sony MX25 Manuale utente

Categoria
Proiettori di dati
Tipo
Manuale utente

Questo manuale è adatto anche per

4-168-447-12 (1)
© 2009 Sony Corporation
Data
Projector
Operating Instructions
Before operating the unit, please read this manual thoroughly
and retain it for future reference.
VPL-MX20/MX25
Not all models are available in all countries and area. Please check
with your local Sony Authorized Dealer.
2
WARNING
WARNING
To reduce the risk of fire or electric
shock, do not expose this apparatus
to rain or moisture.
To avoid electrical shock, do not open
the cabinet. Refer servicing to
qualified personnel only.
WARNING
THIS APPARATUS MUST BE
EARTHED.
WARNING
When installing the unit, incorporate a
readily accessible disconnect device in the
fixed wiring, or connect the power plug to an
easily accessible socket-outlet near the unit.
If a fault should occur during operation of
the unit, operate the disconnect device to
switch the power supply off, or disconnect
the power plug.
Notice for customers
The statements for each country/area are
only applicable to equipment sold in that
country/area.
WARNING: THIS WARNING IS
APPLICABLE FOR USA ONLY.
If used in USA, use the UL LISTED power
cord specified below.
DO NOT USE ANY OTHER POWER
CORD.
Plug Cap Parallel blade with ground pin
(NEMA 5-15P Configuration)
Cord Type SVT, three 18 AWG wires
Length Minimum 1.5 m (4 ft. 11 in.),
Less than 2.0 m (6 ft. 7 in.)
Rating Minimum 7 A, 125 V
Using this unit at a voltage other than 120V
may require the use of a different line cord or
attachment plug, or both.
To reduce the risk of fire or electric shock,
refer servicing to qualified service
personnel.
WARNING: THIS WARNING IS
APPLICABLE FOR OTHER
COUNTRIES.
1 Use the approved Power Cord (3-core
mains lead) / Appliance Connector / Plug
with earthing-contacts that conforms to
the safety regulations of each country if
applicable.
2 Use the Power Cord (3-core mains lead) /
Appliance Connector / Plug conforming
to the proper ratings (Voltage, Ampere).
If you have questions on the use of the above
Power Cord / Appliance Connector / Plug,
please consult a qualified service personnel.
IMPORTANT
The nameplate is located on the bottom.
For kundene i Norge
Dette utstyret kan kobles til et IT-
strømfordelingssystem.
For the customers in the U.S.A
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur in
a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be
determined by turning the equipment off and
on, the user is encouraged to try to correct
the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the
equipment and receiver.
-Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/
TV technician for help.
3
WARNING
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate
this equipment.
All interface cables used to connect
peripherals must be shielded in order to
comply with the limits for a digital device
pursuant to Subpart B of Part 15 of FCC
Rules.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) this device
may not cause harmful interference, and (2)
this device must accept any interference
received, including interference that may
cause undesired operation.
If you have any questions about this product,
you may call;
Sony Customer Information Service Center
1-800-222-7669 or http://www.sony.com/
For the customers in Canada
This Class B digital apparatus complies with
Canadian ICES-003.
For the customers in Europe
The manufacturer of this product is Sony
Corporation, 1-7-1 Konan, Minato-ku,
Tokyo, 108-0075 Japan.
The Authorized Representative for EMC
and product safety is Sony Deutschland
GmbH, Hedelfinger Strasse 61, 70327
Stuttgart, Germany. For any service or
guarantee matters please refer to the
addresses given in separate service or
guarantee documents.
For the State of California, USA only
Perchlorate Material - special handling may
apply, See
www.dtsc. ca.gov/hazardouswaste/
perchlorate
Perchlorate Material: Lithium battery
contains perchlorate.
Disposal of the used lamp
For the customers in the USA
Lamp in this product contains mercury.
Disposal of these materials may be regulated
due to environmental considerations. For
disposal or recycling information, please
contact your local authorities or the
Telecommunications Industry Association
(www.eiae.org
).
For safety
Be sure to attach the air filter to the unit.
For the customers in Taiwan only
Declaration of Conformity
Trade Name: SONY
Model: VPL-MX20
VPL-MX25
Responsible party:
Sony Electronics Inc.
Address: 16530 Via Esprillo, San
Diego, CA 92127U.S.A.
Telephone Number:
858-942-2230
This device complies with part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) this device
may not cause harmful interference, and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.
4
WARNING
For VPL-MX25 only
For the customers in the U.S. A. and
Canada
This device complies with Part 15 of FCC
Rules and RSS-Gen of IC Rules. Operation
is subject to the following two conditions:
(1) this device may not cause interference,
and (2) this device must accept any
interference, including interference that may
cause undesired operation of this device.
This equipment complies with FCC/IC
radiation exposure limits set forth for
uncontrolled equipment and meets the FCC
radio frequency (RF) Exposure Guidelines
in Supplement C to OET65 and RSS-102 of
the IC radio frequency (RF) Exposure rules.
This equipment should be installed and
operated with at least 20cm and more
between the radiator and persons body
(excluding extremities: hands, wrists, feet
and ankles).
For the customers in the U.S.A.
In according with 47 CFR Part15.407 (e) U-
NII devices operating in 5.15-5.25GHz
frequency bands are restricted to indoor
operations only.
This transmitter must not be co-located or
operated in conjunction with any other
antenna or transmitter.
For the customers in Europe
Notice for customers: the following information is only applicable to equipment sold in
Countries applying EU directives.
This product is intended to be used in the following countries:
AT BE BG CY CZ DK EE FI FR DE GR
HU IE IT LV LT LU MT NL PL PT RO
SK SI ES SE GB IS LI NO CH
Bulgarian
Czech
Danish
Undertegnede Sony Corporation erklærer herved, at følgende udstyr VPL-
MX25/Data Projector overholder de væsentlige krav og øvrige relevante krav i
direktiv 1999/5/EF. For yderligere information gå ind på følgende hjemmeside:
http://www.compliance.sony.de/
Dutch
Hierbij verklaart Sony Corporation dat het toestel VPL-MX25/Data Projector in
overeenstemming is met de essentiële eisen en de andere relevante bepalingen
van richtlijn 1999/5/EG. Nadere informatie kunt u vinden op: http://
www.compliance.sony.de/
English
Hereby, Sony Corporation, declares that this VPL-MX25/Data Projector is in
compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC. For details, please access the following URL: http://
www.compliance.sony.de/
С настоящето Сони Корпорация декларира, че този VPL-MX25/Data
Projector отговаря на основните изисквания и другите сьответстващи
клаузи на Директива 1999/5/EC. Подробности може да намерите на
Интернет страницата : http://www.compliance.sony.de/.
Sony Corporation tímto prohlašuje, že tento VPL-MX25/Data Projector
je ve shodě se základními požadavky a dalšími příslušnými ustanoveními
směrnice 1999/5/ES. Podrobnosti lze získat na následující URL:
http://www.compliance.sony.de/
5
WARNING
Estonian
Sony Corporation kinnitab käesolevaga seadme VPL-MX25/Data Projector
vastavust 1999/5/EÜ direktiivi põhinõuetele ja nimetatud direktiivist
tulenevatele teistele asjakohastele sätetele. Üksikasjalikum info: http://
www.compliance.sony.de/.
Finnish
Sony Corporation vakuuttaa täten että VPL-MX25/Data Projector tyyppinen
laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien
direktiivin muiden ehtojen mukainen. Halutessasi lisätietoja, käy osoitteessa:
http://www.compliance.sony.de/
French
Par la présente Sony Corporation déclare que l’appareil VPL-MX25/Data
Projector est conforme aux exigences essentielles et aux autres dispositions
pertinentes de la directive 1999/5/CE. Pour toute information complémentaire,
veuillez consulter l’URL suivante: http://www.compliance.sony.de/
German
Hiermit erklärt Sony Corporation, dass sich das Gerät VPL-MX25/Data
Projector in Übereinstimmung mit den grundlegenden Anforderungen und den
übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Weitere Informationen erhältlich unter: http://www.compliance.sony.de/
Greek
Hungarian
Italian
Con la presente Sony Corporation dichiara che questo VPL-MX25/Data
Projector è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti
stabilite dalla direttiva 1999/5/CE. Per ulteriori dettagli, si prega di consultare il
seguente URL: http://www.compliance.sony.de/
Latvian
Lithuanian
Norwegian
Sony Corporation erklærer herved at utstyret VPL-MX25/Data Projector er i
samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 1999/5/
EF. For flere detaljer, vennligst se: http://www.compliance.sony.de/
Polish
Portuguese
Sony Corporation declara que este VPL-MX25/Data Projector está conforme os
requisitos essenciais e outras disposições da Directiva 1999/5/CE. Para mais
informacoes, por favor consulte a seguinte URL:
http://www.compliance.sony.de/
Με την η Sony Corporation δηλώνει τι VPL-MX25/Data
και τις
λ
της 1999/5/EK. Για
http://www.compliance.sony.de/
Projector
Alulírott, Sony Corporation nyilatkozom, hogy a(z) VPL-MX25/Data
Projector megfelel a vonatkozó alapvető követelményeknek és az
1999/5/EC irányelv egyéb előírásainak. További információkat a
következő weboldalon találhat: http://www.compliance.sony.de/
Niniejszym Sony Corporation oświadcza, ze VPL-MX25/Data Projector
j
est zgodne z zasadniczymi wymaganiami oraz innymi stosownymi
postanowieniami Dyrektywy 1999/5/WE. Szczególowe informacje
znaleźć mozna pod następującym adresem URL:
http:// www.compliance.sony.de/
`
`
6
WARNING
For the customers in France
The WLAN feature of this Data Projector
shall exclusively be used inside buildings.
For the customers in Italy
Use of the RLAN network is governed:
- with respect to private use, by the
Legislative Decree of 1.8.2003, no. 259
(“Code of Electronic Communications”).
In particular Article 104 indicates when
the prior obtainment of a general
authorization is required and Art. 105
indicates when free use is permitted;
- with respect to the supply to the public of
the RLAN access to telecom networks and
services, by the Ministerial Decree
28.5.2003, as amended, and Art. 25
(general authorization for electronic
communications networks and services) of
the Code of electronic communications
- with respect to private use, by the
Ministerial Decree 12.07.2007
For the customers in Cyprus
The end user must register the RLAN
devices in the Department of Electronic
Communications (P.I. 6/2006 and P.I. 6A/
2006).
P.I. 6/2006 is the Radiocommunications
(Categories of Stations Subject to General
Authorization and Registration) Order of
2006.
P.I. 6A/2006 is the General Authorization
for the use of Radiofrequencies by Radio
Local area Networks and by Wireless
Access Systems, including Radio Local
Area Networks (WAS/RLAN).
Romanian
Slovak
Slovenian
Spanish
Por medio de la presente Sony Corporation declara que el VPL-MX25/Data
Projector cumple con los requisitos esenciales y cualesquiera otras
disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Para mayor
información, por favor consulte el siguiente URL:
http://www.compliance.sony.de/
Swedish
Härmed intygar Sony Corporation att denna VPL-MX25/Data Projector står I
överensstämmelse med de väsentliga egenskapskrav och övriga relevanta
bestämmelser som framgår av direktiv 1999/5/EG. För ytterligare information
gå in på följande hemsida: http://www.compliance.sony.de/
Prin prezenta, Sony Corporation declară că acest VPL-MX25/Data
Projector respectă cerinţele esenţiale s¸i este în conformitate cu prevederile
Directivei 1999/5/EC. Pentru detalii, vă rugăm accesaţi următoarea adresă:
http://www.compliance.sony.de/
Sony Corporation týmto vyhlasuje, že VPL-MX25/Data Projector
splňa základné požiadavky a všetky príslušné ustanovenia Smernice
1999/5/ES. Podrobnosti získate na nasledovnej webovej adrese:
http://www.compliance.sony.de/
Sony Corporation izjavlja, da je ta VPL-MX25/Data Projector v skladu z
bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.
Za podrobnosti vas naprošamo, če pogledate na URL:
http://www.compliance.sony.de/
7
WARNING
For the customers in Norway
Use of this radio equipment is not allowed in
the geographical area within a radius of 20
km from the centre of Ny-Ålesund,
Svalbard.
For kunder i Norge
Det er ikke tillatt å bruke dette radioutstyret
innen en radius på 20 km fra sentrum av Ny-
Ålesund, Svalbard.
For the customers in Taiwan
8
Table of Contents
Table of Contents
Precautions .........................................9
Notes on Installation and Usage ......10
Unsuitable Installation ............... 10
Usage in High Altitude ...............11
Unsuitable Conditions ................12
Overview
About the Supplied Manuals ............13
Features ............................................ 14
Location and Function of Controls
(Main Unit) ................................... 16
Top/Front/Side ............................ 16
Rear/Side/Bottom .......................16
Control Panel .............................. 18
Connector Panel .........................19
Remote Commander ........................20
Projecting the Picture
Installing the Projector .....................22
Connecting the Projector .................23
Connecting a Computer ..............23
Connecting a VCR ..................... 24
Projecting .........................................25
Turning Off the Power .....................28
Convenient Functions
Selecting the Menu Language ..........29
Security Lock ...................................30
Other Functions ................................32
Off & Go Function ..................... 32
Effective Tools for Your
Presentation .............................32
Adjustments and Settings
Using a Menu
Using a MENU .................................33
The Picture Menu .............................36
The Screen Menu ..............................38
About the Preset Memory No. ....39
The Setup Menu ...............................40
The Function Menu ..........................42
The Installation Menu ......................44
The Network Setting Menu (VPL-
MX25 only) ...................................46
The Information Menu .....................47
Maintenance
Replacing the Lamp ..........................49
Cleaning the Air Filter ......................51
Others
Troubleshooting ................................52
Messages List ..............................55
Specifications ...................................57
Installation Diagram .........................61
Floor Installation (Front
Projection) ...............................61
Dimensions .......................................63
Index .................................................66
9
Precautions
Precautions
On safety
Check that the operating voltage of your
unit is identical with the voltage of your
local power supply. If voltage adaptation is
required, consult with qualified Sony
personnel.
Should any liquid or solid object fall into
the cabinet, unplug the unit and have it
checked by qualified Sony personnel
before operating it further.
Unplug the unit from the wall outlet if it is
not to be used for several days.
To disconnect the cord, pull it out by the
plug. Never pull the cord itself.
The wall outlet should be near the unit and
easily accessible.
The unit is not disconnected from the AC
power source (mains) as long as it is
connected to the wall outlet, even if the
unit itself has been turned off.
Do not look into the lens while the lamp is
on.
Do not place your hand or objects near the
ventilation holes (exhaust) — the air
coming out is hot.
Be careful not to get your fingers caught in
the adjuster. The powered tilt adjuster of
this unit automatically extends when the
power is turned on, and is retracted
automatically when the power is turned
off. Do not touch the unit while the
adjuster is in operation. Adjust the
powered tilt adjuster carefully after its
automatic operation is completed.
Do not use the product with the filter
removed.
Do not drop in at the exhaust outlet.
On illumination
To obtain the best picture, the front of the
screen should not be exposed to direct
lighting or sunlight.
Cover any windows that face the screen
with opaque draperies.
It is desirable to install the unit in a room
where floor and walls are not of light-
reflecting material. If the floor and walls
are of reflecting material, it is
recommended that the carpet and wall
paper be changed to a dark color.
On preventing internal heat build-
up
The unit is equipped with ventilation holes
(intake) at the bottom and ventilation holes
(exhaust) at the side. Do not block or place
anything near these holes, or internal heat
build-up may occur, causing picture
degradation or damage to the unit.
On cleaning
Before cleaning
Be sure to disconnect the AC power cord
from the AC outlet.
On cleaning the air filter
Clean the air filter regularly.
Refer to the “Cleaning the Air Filter” on
page 51 for the air filter cleaning.
On cleaning the lens cover
The lens cover surface is especially treated
to reduce reflection of light.
As incorrect maintenance may impair the
performance of the projector, take care with
respect to the following:
Avoid touching the lens cover. To remove
dust on the lens, use a soft dry cloth. Do
not use a damp cloth, detergent solution, or
thinner.
Wipe the lens cover gently with a soft cloth
such as a cleaning cloth or glass cleaning
cloth.
Stubborn stains may be removed with a
soft cloth such as a cleaning cloth or glass
cleaning cloth lightly dampened with
water.
Never use solvent such as alcohol, benzene
or thinner, or acid, alkaline or abrasive
detergent, or chemical cleaning cloth, as
they will damage the lens cover surface.
On cleaning the cabinet
Clean the cabinet gently with a soft dry
cloth. Stubborn stains may be removed
with a cloth lightly dampened with mild
detergent solution, followed by wiping
with a soft dry cloth.
Use of alcohol, benzene, thinner or
insecticide may damage the finish of the
10
Notes on Installation and Usage
cabinet or remove the indications on the
cabinet. Do not use these chemicals.
If you rub on the cabinet with a stained
cloth, the cabinet may be scratched.
If the cabinet is in contact with a rubber or
vinyl resin product for a long period of
time, the finish of the cabinet may
deteriorate or the coating may come off.
On LCD projector
The LCD projector is manufactured using
high-precision technology. You may,
however, see tiny black points and/or bright
points (red, blue, or green) that continuously
appear on the LCD projector. This is a
normal result of the manufacturing process
and does not indicate a malfunction.
Also, when you use multiple LCD projectors
to project onto a screen, even if they are of
the same model, the color reproduction
among projectors may vary, since color
balance may be set differently from one
projector to the next.
Lens cover with hardened glass
A lens cover with hardened glass is supplied;
however, it is not unbreakable. If the glass is
shattered, dangerous shards may be
scattered. Take note of the followings:
Do not impact strong shock to the cover by
dropping it from a high location.
Do not scratch it. A deep scratch can lead
to breakage.
Notes on Installation
and Usage
Do not install the unit in the following
situations. These installations may cause
malfunction or damage to the unit.
Poorly ventilated
Allow adequate air circulation to prevent
internal heat build-up. Do not place the
unit on surfaces (rugs, blankets, etc.) or
near materials (curtains, draperies) that
may block the ventilation holes.
When the internal heat builds up due to the
block-up, the temperature sensor will
function with the message “High temp.!
Lamp off in 1 min.” The power will be
turned off automatically after one minute.
Leave space of more than 30 cm (11
7
/8
inches) around the unit.
Be careful that the ventilation holes may
inhale tininess such as a piece of paper.
Highly heated and humid
Avoid installing the unit in a location
where the temperature or humidity is very
high, or temperature is very low.
To avoid moisture condensation, do not
install the unit in a location where the
temperature may rise rapidly.
Unsuitable Installation
11
Notes on Installation and Usage
Subject to direct cool or warm air
from an air-conditioner
Installing in such a location may cause
malfunction of the unit due to moisture
condensation or rise in temperature.
Near a heat or smoke sensor
Malfunction of the sensor may be caused.
Very dusty, extremely smoky
Avoid installing the unit in a very dusty or
extremely smoky environment. Otherwise,
the air filter will become obstructed, and this
may cause a malfunction of the unit or
damage it. Dust preventing the air passing
through the filter may cause a rise in the
internal temperature of the unit. Clean the air
filter whenever you replace the lamp.
When using the unit at an altitude of 1,500 m
or higher, set the “High Altitude Mode” to
“On” in the Setup menu. Failing to set this
mode when using the unit at high altitudes
could have adverse effects, such as reducing
the reliability of certain components.
Note on the screen
When using a screen with an uneven surface,
stripes pattern may rarely appear on the
screen depending on the distance between
the screen and the unit or the zooming
magnifications. This is not a malfunction of
the unit.
Usage in High Altitude
12
Notes on Installation and Usage
Do not use the unit under the following
conditions.
Do not topple the unit
Avoid using as the unit topples over on its
side. It may cause malfunction.
Do not tilt right/left
Avoid using as the unit tilts right or left more
than 20 degrees. Do not install the unit other
than on the floor or ceiling. These
installations may cause malfunction.
Do not tilt the unit backward or
forward
If the unit is left tilted for a certain period of
time, a warning message may appear to
show that the installation angle is outside the
proper range.
Do not block the ventilation holes
Avoid using something to cover over the
ventilation holes (exhaust/intake);
otherwise, the internal heat may build up.
Do not place a blocking object just
in front of the lens
Do not place any object just in front of the
lens that may block the light during
projection. Heat from the light may damage
the object. Use the PIC MUTING key to cut
off the picture.
Unsuitable Conditions
30˚
30˚
13
About the Supplied Manuals
Overview
B Overview
About the Supplied
Manuals
The following manuals are supplied with the
projector.
On Macintosh system, you can read only the
Operating Instructions.
Manuals
Safety Regulations (separately
printed manual)
This manual describes important notes and
cautions to which you have to pay attention
when handling and using this projector.
Quick Reference Manual (separately
printed manual)
This manual describes basic operations for
projecting pictures after you have made the
required connections.
Operating Instructions (on the CD-
ROM) (this manual)
This Operating Instructions describes the
setup and operations of this projector.
Operating Instructions for Network/
USB File Viewer (VPL-MX25 only) (on
the CD-ROM)
This Operating Instructions describes how to
set up and operate the network presentation.
You must have Adobe Acrobat Reader 5.0 or
higher installed to read the Operating
Instructions stored on the CD-ROM.
Note
This manual contains explanations for the
VPL-MX20 and VPL-MX25 together. Be
aware that the VPL-MX25 is mainly used
for explanation of the display, and there
may be an item that is not displayed due to
the model.
14
Features
Features
High brightness, high picture
quality
High brightness
Adopting Sony’s unique new optical system
that incorporates newly developed LCD
panels provides a high-efficiency optical
system. It allows the 200 W Ultra High
Pressure mercury lamp to give a light output
of 2500 lumen.
High picture quality
Three super-high-aperture 0.63-inch (16.0
mm) XGA panels with approximately
790,000 effective pixels, produce a
resolution of 1024 × 768 dots (horizontal/
vertical) for RGB input, and 750 horizontal
TV lines for video input.
Compact and lightweight
The projector is light because the weight is
only about 1.7 kg, and the body is designed
to be thin. This makes the projector
convenient for carrying.
Easy setup and simple operation
Advanced Intelligent Auto-setup
function with auto focus adjustment
Simply press the power key, and the
projector automatically performs the setups
required before use. The projector corrects
the V Keystone, adjusts the focus
automatically, detects a signal, and sets
optimum conditions for projection.
Powered zoom/focus equipped
The projector is equipped with a powered
zoom and powered focus lens, allowing you
to adjust the size and focus of an image with
the Remote Commander away from the
projector.
Short focal lens
The projection distance is very short,
approximately 2.36 m (7.7 feet), when
projecting an 80-inch (2032 mm) image,
which allows projection on a larger screen
even in a limited space.
Off & Go feature
The projector can be moved to another
location, after turning it off and
disconnecting the plug just after use.
Security Functions
Security lock
This function makes it possible to prevent
projection of a picture on the screen unless
the required password is entered when the
projector is turned on.
Panel key lock
This function locks all the keys on the
control panel of the projector, allowing use
of the keys on the Remote Commander. This
prevents the projector from operating
incorrectly.
Network Presentation* (VPL-MX25
only)
If you make the projector part of a LAN
environment, it can project and present a file
not only from a computer connected to the
LAN but also from a remote computer. For
details, refer to the Operating Instructions
for Network/USB File Viewer.
Compatible to the Windows Vista’s
Network Projector function
By using the “Network Projector” function
of Windows Vista, the computer window can
be projected by the projector via the network
with a simple operation.
Remote Desktop
This unit corresponds to Remote Desktop of
Windows XP Professional, Vista, and others.
You can access the computer via LAN from
this projector to project windows or files
from the computer directly.
Network File Viewer
This function helps you give a simple
presentation using a file on the server
without using a computer. You can view
Power Point and Excel files, as well a Wmv
(Microsoft) and Jpeg files.
15
Features
Overview
Streaming
This function enables you to project motion-
picture images via a wireless LAN.
USB Memory Presentation without
a Computer* (VPL-MX25 only)
By connecting USB memory directly to this
unit, you can give a simple presentation
without using a computer. You can view
Power Point and Excel files, as well a Wmv
(Microsoft) and Jpeg files stored in the USB
memory.
Supervising Condition via a
Network* (VPL-MX25 only)
After making the projector part of a LAN
environment, you can control its power or
get information such as its usage period of
time via the Web.
* For details, refer to “Operating
Instructions (For Network/USB File
Viewer)” on the supplied CD-ROM.
Other Convenient Functions
On-screen menu in many languages
Picture muting
•Freeze
Lamp mode switching function
Equiped with “Low” in Standby Mode
About Trademarks
Adobe Acrobat is a trademark of Adobe
Systems Incorporated.
Windows is a registered trademark of
Microsoft Corporation in the United States
and/or other countries.
Kensington is a registered trademark of
Kensington Technology Group.
Macintosh is a registered trademark of
Apple Inc.
VESA is a registered trademark of the
Video Electronics Standards Association.
Display Data Channel is a trademark of the
Video Electronics Standards Association.
All other trademarks and registered
trademarks are trademarks or registered
trademarks of their respective holders. In
this manual, and ® marks are not
specified.
16
Location and Function of Controls (Main Unit)
Location and Function of Controls (Main
Unit)
a Front remote control detector
b Lens cover glass
c Powered tilt adjuster
d Ventilation holes (exhaust)
e Control Panel
For details, see “Control Panel” on
page 18.
f Ventilation holes (intake)
Top/Front/Side
1
4
6
2
6
3
Rear/Side/Bottom
5
9
q;
7
3
6
qa
9
7
6
8
6
6
17
Location and Function of Controls (Main Unit)
Overview
g Adjusters (hind pad)
Turn the appropriate adjuster to the right
or left for minor tilt adjustment of the
projected picture.
h Lamp cover
i Ventilation holes (intake)/Air
filter cover
j Connector Panel
For details, see “Connector Panel” on
page 19.
k Security lock
Connects to an optional security cable
(from Kensington).
Web page address:
http://www.kensington.com/
Do not place anything near the ventilation
holes as this may cause internal heat build-
up.
Do not place your hand near the ventilation
holes and the circumference as this may
cause injury.
To maintain optimal performance, clean the
air filter every 500 hours.
For details, see “Cleaning the Air Filter” on
page 51.
Notes on ventilation holes
18
Location and Function of Controls (Main Unit)
a LAMP/COVER indicators
Flashes in orange under the following
conditions:
A repetition rate of 2 flashes when the
lamp cover is not secured firmly.
A repetition rate of 3 flashes when the
lamp has reached the end of its life or
reaches a high temperature.
For details, see page 54.
b ?/1 (On/Standby) key
Turns on the projector when it is in
standby mode. When you press ?/1 key,
this key flashes in green and then lights
in green when the projector is ready to
operate.
To turn off the power, press the ?/1 key
twice according to the message or hold
the ?/1 key for about two seconds.
?/1 key lights up or flashes under the
following conditions:
Lights in red when the AC power cord
is plugged into a wall outlet. Once the
projector is in standby mode, you can
turn it on with the ?/1 key.
Flashes in red when the internal
temperature is high or the electrical
system has failed.
Lights in green when the projector is
turned on, and when it is ready to
operate.
Flashes in green from the time when
the projector is turned on until the
projector is ready to operate. Also,
flashes in green while the cooling fan
is running after the power is turned off
with the ?/1 key. The fan runs for
about 90 seconds after the power is
turned off.
Lights in orange when the power
saving mode is on.
For details, see page 54.
c INPUT key
Select the input signal. Each time you
press the key the input signal switches.
d MENU key
Displays the on-screen menu. Press
again to clear the menu.
e PIC MUTING key
Cuts off the picture. Press again to
restore the picture.
f Rear remote control detector
g AUTO FOCUS key
Adjusts the picture focus automatically.
h ZOOM/FOCUS key
Each time this key is pressed, ZOOM
and FOCUS adjusting menus are
displayed alternately. Use the arrow keys
Control Panel
76 8 95432 q;1
Rear
19
Location and Function of Controls (Main Unit)
Overview
(v/V/b/B) for adjustment on your
desired menu.
i TILT/KEYSTONE (Trapezoidal
distortion correction) key
Adjusts the tilt of the projector, or the
trapezoidal distortion of the image
manually. Each time you press this key,
the Tilt menu and the V Keystone menu
are displayed in turn. Use the arrow keys
(v/V/b/B) for adjustment.
j PUSH ENTER/v/V/b/B (Arrow)
keys
Used to enter the settings of items in the
menu system, select a menu, or make
various adjustments.
a AC IN socket
Connects the supplied AC power cord.
b USB connector (type A) (VPL-
MX25 only)
Uses to view files saved on media with
USB connection.
The projector cannot be connected with the
computer by connecting the USB cable to
the USB connector on the projector.
c VIDEO jack (phono type)
Connects to the composite video output
of video equipment.
d INPUT A (Analog RGB)
connector (HD D-sub 15-pin,
female)
Inputs a computer signal, video GBR
signal, component signal, or DTV signal
depending on the connected equipment.
Connects to the output connector of
equipment using the supplied cable or an
optional cable.
For details, see “Connecting a
Computer” on page 23 and
“Connecting a VCR” on page 24.
Connector Panel
2 3 41
Side
Note
20
Remote Commander
Remote Commander
The keys that have the same names as those
on the control panel function identically.
a NETWORK key
Displays the home window of a Network
presentation.
For details, refer to “Operating
Instructions (For Network/USB File
Viewer)” on the supplied CD-ROM.
No key may function immediately after
connecting the AC power cord, as the
unit is starting up.
b INPUT key
c MENU key
d ENTER/
v/V/b/B (Arrow) keys
e RESET key
Resets the value of an item to its factory
preset value or returns the enlarged
image with D ZOOM key to its original
size. This key functions when the menu
or a setting item is displayed on the
screen.
f AUTO FOCUS key
g D ZOOM (Digital Zoom) +/– key
Enlarges the image at a desired location
on the screen.
h VOLUME +/– keys
This function is not provided in this
projector.
i Infrared transmitter
j ?/1 (On/Standby) key
k USB key
Displays the home window of a PC
presentation from USB memory.
For details, refer to “Operating
Instructions (For Network/USB File
Viewer)” on the supplied CD-ROM.
No key may function immediately after
connecting the AC power cord, as the
unit is starting up.
l APA (Auto Pixel Alignment) key
Automatically adjusts a picture to its
clearest while a signal is input from a
computer.
For details, see “Smart APA” in “The
Function Menu” on page 42.
m LENS key
Functions as a ZOOM/FOCUS key.
n KEYSTONE (Trapezoidal
distortion correction) /TILT key
o PIC MUTING key
p AUDIO MUTING key
This function is not provided in this
projector.
q FREEZE key
Freezes the projected picture. To cancel
the frozen picture, press the key again.
This function is available when the PC
signal is input.
Note
2
0
qa
qd
qf
qg
qs
3
5
6
7
8
4
1
qh
qj
9
INPUT
MENU
NETWORK USB
RESET
AUTO FOCUS
D ZOOM
LENS
ENTER
VOLUME
KEYSTONE
/TILT
FREEZE
PIC MUTING
AUDIO MUTING
APA
Note
1 / 1

Sony MX25 Manuale utente

Categoria
Proiettori di dati
Tipo
Manuale utente
Questo manuale è adatto anche per

in altre lingue