DTS Raptor Manuale utente

D.T.S. Illuminazione s.r.l.

Via Fagnano Selve 10/12/14

47843 Misano Adriatico (RN) ITALIA Tel +39 0541 611131 Fax +39 0541 611111 info@dts-lighting.it http://www.dts-lighting.it

Made in Italy

2

Le informazioni contenute in questo documento sono state attentamente redatte e

controllate. Tuttavia non è assunta alcuna responsabilità per eventuali inesattezze.

Tutti i diritti sono riservati e questo documento non può essere copiato, fotocopiato,

riprodotto per intero o in parte senza previo consenso scritto della D.T.S .

D.T.S. si riserva il diritto di apportare senza preavviso cambiamenti e modifiche

estetiche , funzionali o di design a ciascun proprio prodotto. D.T.S non assume alcuna

responsabilità sull’uso o sull’applicazione dei prodotti o dei circuiti descritti.

The information contained in this publication has been carefully prepared and

checked. However, no responsibility will be taken for any errors. All rights are

reserved and this document cannot be copied, photocopied or reproduced, in part or

completely, without prior written consent from D.T.S.

D.T.S. reserves the right to make any aesthetic, functional or design modifications to

any of its products without prior notice. D.T.S. assumes no responsibility for the use or

application of the products or circuits described herein.

Les informations contenues dans le présent manuel ont été rédigées et contrôlées

avec le plus grand soin. Nous déclinons toutefois toute responsabilité en cas

photocopié ou reproduit, dans sa totalité ou partiellement, sans le consentement

préalable de D.T.S.

D.T.S. se réserve le droit d'apporter toutes modifications et améliorations esthétiques,

fonctionnelles ou de design, sans préavis, à chacun de ses produits. D.T.S. décline

toute responsabilité sur l'utilisation ou sur l'application des produits ou des circuits

décrits.

Las informaciones contenidas en este documento han sido cuidadosamente

redactadas y controladas. Con todo, no se asume ninguna responsabilidad por

eventuales inexactitudes. Todos los derechos han sido reservados y este documento

no puede ser copiado, fotocopiado o reproducido, total o parcialmente, sin previa

autorización escrita de D.T.S.

D.T.S. se reserva el derecho a aportar sin previo aviso cambios y modificaciones de

carácter estético, funcional o de diseño a cada producto suyo. D.T.S. no se asume

responsabilidad de ningún tipo sobre la utilización o sobre la aplicación de los

productos o de los circuitos descritos.

3

INDEX:

1- SYMBOLS 4

2- GENERAL WARNING 5

3- GENERAL WARRANTY CONDITION 5

4- TECHNICAL FEATURES 6

5- ACCESSORIES 8

6- IMPORTANT SAFETY INFORMATION 9

6.1 Fire prevention

6.2 Prevention of electric shock

6.3 Protection against ultraviolet radiation

6.4 Safety

6.5 Level of protection against the penetration of solid and liquid objects

7- MOUNTING / REPLACING THE LAMP AND LAMP ALIGNMENT 10

8- VOLTAGE AND FREQUENCY 15

9- INSTALLATION 15

9.1 Safety cable

9.2 Protection against liquids

9.3 Movement

9.4 Risk of fire

9.5 Forced ventilation

9.6 Ambient temperature

10- MAINS CONNECTION 18

10.1 Protection

11- DMX SIGNAL CONNECTION 19

11.1 DMX Addresses

11.2 Selecting the DMX address

12- FIRMWARE UPDATING 20

13- DISPLAY FUNCTIONS 21

14- ERROR MESSAGES 25

15- HIDDEN MENU 26

15.1 Calibration mode

15.2 Power Setup menu

16- PAN SPEED & TILT SPEED 29

17- OPENING THE PROJECTOR HOUSING 29

18- PERIODIC CLEANING 30

18.1 Lenses and reflectors

18.2 Fans and air passages

19- PERIODIC CONTROLS 30

20- DMX PROTOCOL 31

21- FIXED GOBO WHEEL 38

22- COLOUR WHEEL 39

4

1- SYMBOLS

Graphic symbols used on this manual:

THIS SYMBOL INDICATES A HOT SURFACE

THIS SYMBOL INDICATES ELECTRIC

SHOCK RISK

THIS SYMBOL INDICATES GENERAL RISK

THIS SYMBOL MEANS “DO NOT PLACE THE

UNIT ON INFLAMMABLE SURFACES”

THIS SYMBOL MEANS “RADIATION FROM

THIS LAMP CAN CAUSE DAMAGE TO EYES

AND SKIN”

MINIMUM DISTANCE FROM THE OBJECTS

AND THE PEOPLE LIT BY THE LIGHT BEAM

!

F

UV

15M

5

2- GENERAL WARNING

Read the instruction contained in this user manual carefully, as they give important

information regarding safety during installation, use and maintenance.

The device is not for domestic use and must be installed by a qualified electrician or

experienced person.

Always disconnect the device from the mains before replacing the lamp.

The lamp must be replaced if it has been damaged or deformed by prolonged use or

overheating.

The device must always be equipped with an efficient ground connection.

MINIMUM DISTANCE FROM THE OBJECTS AND THE PEOPLE

The projector needs to be positioned so that the objects and the people hit by the

beam of light are at least 15 meters (49,21 ft) from the unit frontal lens.

3- GENERAL WARRANTY CONDITIONS

The unit is guaranteed for 36 months from the date of purchase against manufacturing

material defects.

6

4- TECHNICAL FEATURES

Overview

RAPTOR is the most compact Beam moving head on the market: just 37 cm x 50 cm.

RAPTOR projects the most powerful beam of light (150.000 Lux at 15 m) and the most

concentrated one.

RAPTOR can perfectly focus its 17 gobos at any distance.

Its unique selectable ‘Smooth’ filter eliminates the hot spot typical of Beam projectors,

evenly diffusing luminosity at any point of the light beam.

RAPTOR comes equipped with the ‘FPR’ (patented) system, which allows limitless

pan rotation, in either direction, never having to reverse motion.

Also, the unit features the fastest strobe effect.

RAPTOR

(D.T.S. Product Code: 03.MB005.EB.L)

• Electronic ballast 90-260V 50/60 Hz • Black finish

RAPTOR FPR

(D.T.S. Product Code: 03.MB005.EB.LFP)

• Electronic ballast 90-260V 50/60 Hz • FPR (Free Pan Rotation) • Black finish

Lamp

Osram Sirius HRI 330W (16.500 Lumens)

Colour temperature: 7.500°K

Optical group

Beam opening: 0,6° - 3,4°

16-bit motorized linear focus

Linear dimmer / shutter / ultra-fast strobe

150.000 Lux at 15 m

Colour generation

17-colour wheel with linear selection for perfect 2-colour beams

Dynamic effects

17-gobo wheel

8-facet rotating prism

Filters

Smooth filter (eliminates the hot spot, evenly diffusing luminosity)

Frost filter

7

4- TECHNICAL FEATURES

Interface / Control / Programming

LCD graphic display (control / management / monitoring of the main parameters)

4 soft-keys

Controlled via DMX 512

RDM

Wireless ready

ARTNET available on request

Internal operating system updatable via D.T.S. RED BOX interface and

hyperterminal program on windows based PC

DMX

18 DMX channels

Pan & Tilt

RAPTOR FPR (03.MB005.EB.LFP)

'FPR': limitless pan rotation, in either directions, never having to reverse motion

Tilt 270° (1,2 sec.)

RAPTOR (03.MB005.EB.L)

Pan 540° (2,3 sec.); Tilt 270° (1,2 sec.)

New Tri-phase stepper motor technology for ultra-fast and silent Pan &Tilt movements

16-bit movement resolution

Power supply

Electronic ballast: 90-260V 50/60 Hz

Power consumption: 450W with PFC

Energy saving

Power saving mode (the lamp dims to 80% after shutter closure)

Connectors

DMX: 4x XLR connectors (3-pole In and Out; 5-pole In and Out) by Neutrik;

Power supply: POWERCON connectors (Power In / Power Out) by Neutrik

Operating ambient temperature

-10° / 40°

Weight

15,4 Kg

Internal safety devices

Overvoltage circuit protection and overtemperature circuit protection

International certifications

Safety: EN 60598-1: 2009

EN 60598-2-17: 1989

EMC: EN 55015.2006

8

4- TECHNICAL FEATURES

Dimensions

Packaging Dimensions (LxWxH) Unit Dimensions (LxWxH)

420 x 440 x 580 mm 368x288x538mm

Weight: 18,9 Kg Weight: 15,4 Kg

5- ACCESSORIES

As standard

* 1 x Osram Sirius HRI 330W (already installed in the projector) (Code 0505S037)

* 1 x POWERCON male cable connector (Code 0520P014)

* 1 x XLR 5 Pins male cable connector (Code 0508B066)

* 1 x XLR 5 Pins female cable connector (Code 0508B065)

* 2 x Omega clamp with “Fast Lock” connection 1/4 turn

* User’s manual

Optional (on request)

• “C” Clamp G100 black / professional (max. load 200Kg) (Code 0521A015)

• Aliscaf Clamp (max. capacity load 100Kg) (Code 0521A008)

• Safety wire (3mm x 60 cm), ring spring catch, max. capacity load 60Kg (Code

0521A010)

9

6- IMPORTANT SAFETY INFORMATION

6.1 Fire prevention:

RAPTOR uses a Osram Sirius HRI 330W lamp.

The use of any other alternative lamp is not recommended and will null and void the

fixture's warranty.

-Never locate the fixture on any flammable surface.

-Minimum distance from flammable materials: 1 m .

-Minimum distance from the closest illuminable surface: 15 m.

-Replace any blown or damaged fuses only with those of identical value (5AT).

Refer to the wiring diagram if there is any doubt.

-Connect the projector to mains power via a thermal magnetic circuit breaker.

6.2 Prevention of electric shock:

-High voltage is present inside the unit.

Unplug the unit prior to performing any function which involves touching the inside of

the moving head, including lamp replacement.

-The level of technology inherent in the RAPTOR requires the assistance of

specialised personnel for all servicing.

Please refer to an authorised D.T.S. service centre.

-A good earth connection is essential for proper functioning of the projector.

-Never connect the unit without proper earth connection.

-The fixture should be located in places with a good air ventilation.

6.3 Protection against ultraviolet radiation:

-Never turn on the lamp if any of the lenses, filters or plastic covering are damaged.

Their respective shielding functions will only operate efficiently if they are in perfect

working order.

-Never look directly the lamp when it is on.

6.4 Safety:

-The projector should always be installed with bolts, clamps and other tools that are

capable of supporting the weight of the unit.

-Always use a second safety cable to sustain the weight of the unit in case of the

failure of the main fixing point.

-The external surface of the unit, at various points, may exceed 70°C. Never handle

the unit until at least 20 minutes have elapsed since the lamp was turned off.

-Always replace the lamp if any physical damage is evident.

-Never install the fixture in an enclosed area lacking sufficient air flow.

The ambient temperature should not exceed 40°C.

-A hot lamp may explode, so always wait for at least 20 minutes prior to attempting to

replace the lamp.

-Always wear suitable hand protection when handling the lamp.

6.5 Level of protection against the penetration of solid and liquid objects:

-The projector is classified as an ordinary appliance and its protection level against the

penetration of solid and liquid objects is IP20.

For outdoor use, D.T.S. reccomend the use of the dedicated raincovers.

F

UV

!

15M

10

7- MOUNTING / REPLACING THE LAMP AND LAMP ALIGNMENT

WARNING

Turn off the lamp before opening the unit head covers.

Never look directly at the lamp when it’s lit.

Discharge lamps emits UV rays; radiation from this lamp

can cause damage to eyes and skin.

Let the projector cool for at least 20 minutes.

Switch off the unit and unplug the Mains AC cable connector

before replacing the lamp.

REPLACEMENT LAMP (D.T.S. Code 0505S037) :

OSRAM SIRIUS HRI

Power 330W

Luminous flux 16.500 lm

Colour temperature 7.500°K

Rated life 1500 hours

The use of any other alternative lamp is not recommended and will null and void the

fixture's warranty.

!

UV

11

1) Loosen the 3 “¼ turn” screws which fix the head covers on both sides (picture 1) .

2) Once loosened the screws, simply lift the covers to access the internal components

(picture 2).

PICTURE 1 PICTURE 2

3) Unplug the indicated fan connectors from the fans resend card (picture 3);

Unplug the two indicated fast-on cable connectors (1 and 2) and using a flathead

screwdriver remove the indicated lamp cable (3) from the screw connector (picture 4).

PICTURE 3 PICTURE 4

12

4) Using a phillips screwdriver, loose the 4 screws A, B, C, D and remove the lamp fan

assembly (picture 5).

PICTURE 5

5) Loose the four screws E, F, G, H from the plate which fix the lamp (picture 6), then

loose the two screws on both sides of the lamp rear metal cover (picture 7) and

remove the old lamp.

PICTURE 6 PICTURE 7

13

6) Remove the cable connectors from the old lamp and apply them on the new lamp

(picture 8).

PICTURE 8

7) Put in place the new lamp in the lamp support.

Place the lamp connectors on the fan air conveyor side (picture 9).

PICTURE 9

8) Lamp sub-assembly can now be re-installed, following backward all the above

listed steps.

14

Lamp Alignment

Attention: we recommend to align the lamp in the optical system to avoid overheating

of the dichroic filters and other components inside the unit.

The lamp alignment is also essential to obtain the maximum luminous performance by

the projection.

1) Mount the fixture in an orientation so that it may be squarely projected onto a

smooth white surface no less than 20 meters away.

2) Using a console or the “LAMP ADJUST” menu system, focus and open (white)

beam onto the surface and observe the beam.

3) Using a phillips screwdriver, rotate the 3 indicated adjusters until you achieve a hot

spot in the center.

When the lamp alignment is correctly optimized, you will have a hot spot in the center.

15

8- VOLTAGE AND FREQUENCY

The RAPTOR with electronic ballast can operate at 90-260V 50 or 60 Hz.

9- INSTALLATION

RAPTOR may be either floor or ceiling mounted.

For floor mounting installations, the RAPTOR is supplied with four rubber mounting

feet on the base.

For ceiling mounted installations, we reccomend the use of appropriate clamps to fix

the unit to the mounting surface.

The supporting structure from which the unit is hung should be capable of bearing the

weight of the unit, as should any clamps used to hang it.

The structure should also be sufficiently rigid so as not to move or shake whilst the

RAPTOR is moving.

Four 1/4 turn Fast Locks connections placed in the base of the unit allow to hang the

RAPTOR by using the two omega clamps (provided in the box) in conjunction with

fixing clamps for truss (fixing clamps are not included into the unit box).

16

9.1- Safety cable

We recommend the use of a safety cable or chain connected to the RAPTOR and to

the suspension truss in order to avoid the fixture accidentally falling should the main

fixing point fail.

Make sure that the iron cable or chain can bear the weight of the entire unit.

You may attach the safety chain/cord to the attachment point (A) located on the base

of the fixture, as shown in the picture below.

9.2 Protection against liquids

The projector contains electric and electronic components which should under no

circumstances come into contact with oil, water or any other liquid.

The proper unit functioning would be compromised should this occur.

!

17

15M

9.3- Movement

RAPTOR FPR (03.MB005.EB.LFP) Unlimited Pan rotation; Tilt 270° (1,2 sec.) .

RAPTOR (03.MB005.EB.L) Pan 540° (2,3 sec.); Tilt 270° (1,2 sec.) .

Do not place any obstructions in the path of the projector's movement.

WARNING

Do not place any object in the

path of the projector’s

movement

Free Pan Rotation (‘FPR’) No ‘FPR’

(03.MB005.EB.LFP) (03.MB005.EB.L)

Please Note: If two different RAPTOR model (with and without FPR) are controlled at

the same time via DMX controller, be shure that channel 6 (PAN FAR) is set to value

0. In this way, the RAPTOR with FPR will react to DMX same as RAPTOR with no

FPR function.

9.4- Risk of fire

Each fixture produces heat and must be installed in a well-ventilated place.

The minimum recommended distance from flammable material is 1 m.

Minimum distance from the object being illuminated is 15 m.

9.5- Forced ventilation

You will note, on inspection, that the unit features various air inlets and cooling fans

located on both the base and head of the fixture.

These should, under no circumstances, be blocked or obstructed whilst the projector

is in operation. Doing so could cause the fixture to seriously overheat thereby

compromising its proper operation.

9.6- Ambient temperature

The projector should never be installed in places that lack a constant air flow.

The ambient temperature should NOT exceed 40°C.

F

!

18

10- MAINS CONNECTION

RAPTOR with electronic ballast operate at 90-260V 50-60 Hz.

Prior to connecting the unit to your mains supply, ensure that the model in your

possession correctly matches the mains supply available.

For connection purposes, ensure that your plug is capable of supporting 1,5 amps

at 230 VOLT, or 3 amps at 90 VOLT.

Strict adherence to regulatory norms is strongly recommended.

MAINS AC OUTPUT 90-260V 50/60 Hz (16A Max)

MAX 6 RAPTOR UNITS @ 230V

MAX 3 RAPTOR UNITS @ 120V

(03.MB005.EB.LFP)

(03.MB005.EB.L)

MAINS AC INPUT 90-260V 50/60 Hz

FUSE 5A T 5X20

10.1- Protection

The use of a thermal magnetic circuit breaker is recommended for each RAPTOR.

A good earth connection is essential for the correct operation of the projector.

!

19

11- DMX SIGNAL CONNECTION

The unit operates using the digital DMX 512 (1990) signal.

Connection between the mixer and the projector or between projectors must be carried

out using a two pair screened ø 0.5 mm cable and a XLR 5 or 3 pins connector.

Ensure that the conductors do not touch each other.

Do not connect the cable ground to the XLR chassy.

The plug housing must be isolated. Connect the mixer signal to the DMX IN projector

plug and connect it to the next projector by connecting the DMX OUT plug on the first

projector to the DMX IN plug of the second one.

This way, all the projectors are cascade connected.

NB. If the display showing the DMX address flashes, then one of the following errors

has occurred:

- DMX signal not present

- DMX address not valid

- DMX reception problem

For Installations where long distance DMX cable connections are needed, we suggest

to use a DMX terminator.

The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor

between pin 2 and 3.

The DMX terminator must be plugged into the last unit (DMX out panel connector) of

the DMX line.

PLACE A 120 OHM RESISTOR BETWEEN PIN 2

AND 3 OF A MALE XRL CONNECTOR AND PLUG IT

INTO THE DMX OUT PANEL CONNECTOR OF THE

LAST UNIT CONNECTED TO THE DMX LINE

1

2

3

5

4

OUT

120 ohm

PIN 3

PIN 2

20

11.1-DMX Addresses

RAPTOR can be controlled with 18 DMX channels.

In order to use the unit in 18 channels, set the following addresses on the mixer:

Projector 1 A001

Projector 2 A019 If you want to select the next projector, just add “18”

Projector 3 A037

….. A….

projector 6 A091

11.2-Selecting the DMX address

1) Press the UP-DOWN key until you reach the required DMX channel. The numbers

on the display will start to flash (but the new DMX address hasn't yet been set).

2) Press ENTER to confirm your selection. The numbers on the display will stop

flashing and the projector is now setted to the new DMX address.

TRICKS:

If you keep pushed the UP or DOWN keys, the channels are calculated more quickly

and you get a faster selection.

12- FIRMWARE UPDATING

Warning:

This procedure require a base knowledge of computer applications and Windows

Hyperterminal program. Please refer to an authorised D.T.S. service centre.

To update the software version of the RAPTOR you need:

D.T.S. RED BOX interface (D.T.S. Code: 03.LA.008).

USB-DMX Driver for the D.T.S. RED BOX interface.

(The driver and the installation procedure are available in our web site

www.dts-lighting.it)

Updating the software version.

Please follow the procedure below to perform the update:

1. Install the D.T.S. RED BOX USB-DMX driver on the PC you will use to update the

unit software.

2. Connect the D.T.S. RED BOX interface to the PC by using a USB cable.

3. Connect the D.T.S. RED BOX interface to the fixture by using a DMX cable.

4. Download the new software version into the unit by using Windows Hyperterminal

program.

It will be possible to download the software from the reserved area of D.T.S. web site:

www.dts-lighting.it.

!

La pagina sta caricando ...

DTS Raptor Manuale utente

DTS Raptor Manuale utente

in altre lingue

Documenti correlati

Altri documenti