TomTom RIDER 2 Manuale del proprietario

TomTom RIDER

What’s in the box1.

2

What’s in the box

A Your TomTom RIDER

a Touchscreen

b On/Off button

c Memory card (SD card) slot

d USB connector

e Charging connector

f Reset button

B A memory card (SD card)

C Cardo scala-rider™ Bluetooth®

headset

D RAM Mount™ mounting kit

E Holder and security strap F TomTom RIDER case

1

2

3

4

5

6

3

G Home Charger H Documentation pack

I Battery cable J USB cable

Using your TomTom RIDER2.

4

Using your TomTom RIDER

Switching on

1. Open the compartment on the bottom of your TomTom RIDER.

2. Push the memory card into the memory card slot.

3. Press and hold the On/Off button for 2 seconds, or until your

TomTom RIDER starts.

The first time you switch on your TomTom RIDER, it may take up to 20

seconds to start. To switch off your TomTom RIDER, press and hold the On/

Off button for 2 seconds.

Setting up

First, you have to answer a few questions to set up your device and your

Cardo scala-rider™ headset. Answer the questions by tapping the screen. You

will use the touchscreen for everything you do with your TomTom RIDER.

Follow the instructions to establish a Bluetooth connection between your

TomTom RIDER and your Cardo scala-rider™ headset.

Once you have answered the questions, your TomTom RIDER will display the

Driving View.

The screen is shown in black and white until your TomTom RIDER locates

your current position.

Charging your TomTom RIDER

Before you use your RIDER for the first time, it’s a good idea to charge it fully

using the home charger, which takes about 2 hours.

There is no charging light on your RIDER. To check the battery status and see

when your RIDER is charging, switch on your device and tap the bottom right-

hand corner of the screen in the Driving View. The battery status is shown on

the next page.

5

Cardo scala-rider™ headset

A Microphone

B On/off button

C Speaker

D LED

E Volume down

F Volume up

G Charging connector

Before you can use your Bluetooth headset, fully charge the headset using the

charger supplied with the headset.

Note: Make sure you use the correct charger. There are different chargers for

your TomTom RIDER and your headset. Using the wrong charger may

damage the device.

To fully charge the headset takes between 2 and 3 hours. When charging, the

LED is a steady red. When charging is finished, the LED turns off.

When the batteries are running low, an alert tone is played.

Using your headset

To turn the headset on, press and hold the on/off button for 6 seconds, until

the LED flashes blue 3 times. An ascending alert tone is played. When the

headset is on, the LED flashes blue every 3 seconds.

To turn the headset off, press and hold the on/off button for 3 seconds, until

the LED flashes red 3 times. A descending alert tone is played.

If you did not establish a Bluetooth connection between your Bluetooth

headset module and your TomTom RIDER when you first turned your RIDER

on, you can establish the connection at any time.

From the Main Menu, tap Change Preferences. Tap Connect to headset and

follow the instructions to establish the connection.

Attach your headset to your helmet as shown in the Installation Poster. Make

sure you position the microphone correctly. For best results, don’t position the

microphone directly in front of your mouth, position it just to the side of your

mouth.

A

B

C

E

D

F

G

6

Locating your current position

Your TomTom RIDER must be outside to be able to locate your current

position. Make sure that you are in an open place without tall buildings or trees

around you.

The first time you start your RIDER, it can take a few minutes for the device to

find your current position. In the future, your position will be found much

faster, normally within a few seconds.

Your RIDER does not transmit your location, so others cannot use it to track

you while you are driving.

TomTom RIDER uses a GPS receiver to locate your current position.

Mounting your navigation device

Attach the RAM™ mount kit to your motorcycle as shown on the Installation

Poster, then place your RIDER in the holder. When you are attaching the

mount kit to your motorcycle, follow these guidelines:

• If you are unsure about attaching the mount kit yourself, ask a professional

to fit it for you.

• Make sure that the mount kit does not interfere with any of the controls on

the motorcycle.

• Always use the correct tools. If you use unsuitable tools, you may damage

or break the mount kit.

• Do not overtighten nuts. You may crack parts of the mount kit or damage

your handlebars if you overtighten the nuts.

• If you are using the u-bolt, don’t forget to put the rubber caps provided over

the exposed threads.

Damage due to modifications, improper installation, road hazards or accident,

are not covered. Neither RAM nor TomTom shall be liable for any injury, loss,

or damage, direct or consequential, arising out of improper installation, or

inability to use product. Before use, the user shall determine the suitability of

the product for its intended use. The user assumes all risk and liability,

whatsoever, in connection with the mount.

Secure your TomTom RIDER

Set a password for your TomTom RIDER so that only you can use it. Every

time you start your RIDER you will have to enter your password.

To set the password, you have to run your RIDER using TomTom HOME. You

can then use TomTom HOME to set the password. To set a password on your

device, do the following:

1. Connect your RIDER to your computer and switch it on.

2. Start TomTom HOME if it does not start automatically.

If you do not have TomTom HOME installed, insert the CD that came with

your RIDER to install it.

Alternatively, you can download TomTom HOME from www.tomtom.com.

Make sure you always have the latest version of TomTom HOME.

3. In the Planning section, select your RIDER.

A picture of your RIDER is shown in the main section of TomTom HOME.

7

4. Click the On/Off button on the picture of your RIDER to switch it on in

TomTom HOME.

Your RIDER starts in TomTom HOME. You can now set the password on

your RIDER using TomTom HOME. Don't unplug your RIDER, just use it as

you normally would by clicking the buttons shown on your computer.

5. From the Main Menu in your device, click Change preferences.

6. Click Set owner. You may have to click the arrow until you reach the page

where Set owner is shown.

You can now set the password for your RIDER. You can also set your name

and address, which will then be shown when your RIDER starts up.

Take care of your navigation device

It is important to take care of your RIDER and to clean it correctly.

• Use a soft cloth to wipe the screen of your RIDER; do not use any liquid

cleaners.

• If your RIDER gets wet, dry it with a soft cloth.

• Do not open the casing of your RIDER under any circumstances. Doing so

may be dangerous and will invalidate your warranty.

• Do not use the memory card (SD card) with any device other than a

TomTom device. Other devices may damage the memory card.

• Do not expose your RIDER to high or low temperatures, which can cause

permanent damage. For example, don’t leave it on your motorcycle or in

the car on hot summer days or during cold winter nights.

Backup your navigation device

It’s always a good idea to make a backup of the contents of your

TomTom RIDER. You can make a backup using TomTom HOME. You can

install TomTom HOME using the CD that came with your TomTom RIDER.

Set owner

If you cannot find the button Set owner, make sure that all buttons are

shown in your RIDER. Tap the button Show ALL menu options. All

buttons will now be shown.

Making your first journey3.

8

Making your first journey

Planning a route with your TomTom RIDER is easy. To plan your first route,

follow the steps below.

Important: You have to plan your journey before you start riding. For safety,

once you start moving only the Safety Driving Menu is shown.

1. Tap the screen to bring up the Main Menu.

Note: The buttons on your RIDER are shown in full colour unless a button is

currently unavailable. For example, the button named Find alternative... in

the Main Menu is not available until you have planned a route.

2. Tap Navigate to...

3. Tap Address.

When you enter an address, you can choose from the following options:

• City centre - tap this button to set your destination as the centre of a city

or town.

• Street and house number - tap this button to set an exact address as your

destination.

• Postcode - tap this button to enter a postcode as your destination.

Note: You can enter a postcode for any country. In the UK and the

Netherlands, postcodes are detailed enough to identify a house on their own.

9

In other countries you can enter a postcode to identify a town or area. You will

then have to enter a street and house number.

• Crossing or intersection - tap this button to set your destination as the

point where two streets meet.

In this example, we will enter an exact address.

4. Tap Street and house number.

Note: When planning a trip for the first time your RIDER asks you to choose a

country. Your choice is saved and used for all routes you plan.

You can change this setting at any time by tapping the country flag.

5. Start to type the name of the town where you want to go.

As you type, the names of the towns that match what you have typed are

shown. When your destination appears in the list, tap the name of the town

to set the destination.

6. Start to type the name of the street and select it when it is shown.

As with the name of the town, the names of the streets that match what you

have typed are shown. When your destination appears in the list, tap the

name of the street to set the destination.

7. Now enter the house number of your destination and then tap Done.

8. Your RIDER asks if you need to arrive at a particular time. For this exercise,

tap NO.

10

The route is calculated by your RIDER.

9. When the route has been calculated, tap Done.

Your RIDER will immediately begin to guide you to your destination, using

both spoken instructions and on-screen directions.

Arrival times

When you plan a route, your TomTom RIDER asks you if you need to arrive at

a particular time.

Tap YES to enter a preferred arrival time.

Your RIDER calculates your arrival time and shows you whether you will arrive

on time.

You can also use this information to work out when you need to leave. If your

RIDER shows that you will arrive 30 minutes early, you can wait and leave in

30 minutes time, rather than arrive early.

Your arrival time is constantly recalculated during your journey. The status bar

shows whether you will arrive on time or if you are going to be late, as shown

below:

You will arrive 55 minutes before the arrival time you entered.

If the estimated arrival time is more than five minutes before

the time you entered, it is shown in green.

You will arrive 3 minutes before the arrival time you entered.

If the estimated arrival time is less than 5 minutes before the

time you entered, it is shown in yellow.

You will arrive 19 minutes late.

If the estimated arrival time is later than the time you entered,

it is shown in red.

Status bar

preferences

Tap Status bar preferences in the Preferences menu, to enable or disable

arrival time notifications.

Select the required options on the first menu screen and then tap Done.

To enable arrival time notifications, select Show leeway to arrival time.

11

What are the other navigation options?

When you tap Navigate to..., you can set your destination in many ways, not

just by entering the address. The other options are listed below:

Home

Tap this button to navigate to your Home location.

You will probably use this button more than any other.

Favourite

Tap this button to select a Favourite as your destination.

Address

Tap this button to enter an address as your destination.

Recent

destination

Tap this button to select your destination from a list of places you have

recently used as destinations.

Point of

Interest

Tap this button to navigate to a Point of Interest (POI).

Point on map

Tap this button to select a point on the map as your destination using the

map browser.

Latitude

Longitude

Tap this button to enter a destination using latitude and longitude values.

TomTom

Buddy

Tap this button to navigate to the last known position of a TomTom Buddy.

Don’t forget that the Buddy may move before you reach him.

Position of

last stop

Tap this button to select your last recorded position, as your destination.

2

3

1

2

12

Planning a route in advance

You can also use your RIDER to plan journeys in advance by selecting both

your starting point and your destination. You could, for example, do the

following:

• Find out how long a journey is going to take before you start.

• Check the route of a journey you are planning.

• Check a route for someone who is coming to visit you, so that you can

explain the route to them.

To plan a route in advance, follow these steps:

1. Tap the screen to bring up the main menu.

2. Tap the arrow button to move to the next menu screen and tap Prepare

route.

3. Select the starting point for your journey in the same way that you would

select your destination.

4. Set the destination for your journey.

5. Choose the type of route that should be planned.

• Fastest route - the route which takes the least time.

• Shortest route - the shortest distance between the locations you set. This

may not be the quickest route, especially if the shortest route is through

a town or city.

• Avoid motorways - a route which avoids motorways.

• Walking route - a route designed for making the journey on foot.

• Bicycle route - a route designed for making the journey on a bicycle.

• Limited speed - a route for a vehicle which can only be driven at a limited

speed. You have to specify the maximum speed.

6. Your TomTom RIDER plans the route between the two locations you

selected.

More information about a route

You can access these options for the route you last planned by tapping View

route in the Main Menu or the Details button on the route summary screen.

You can then select from the following options:

Prepare route

Browse as

text

Tap this button for a list of all the turn instructions on the route.

This is very useful if you need to explain a route to someone else.

Browse as

images

Tap this button to see each turn in the journey. Tap the right and left arrows

to move forwards and backwards through the journey.

Tap the screen to turn off the 3D display and view the map from above.

13

Browse map

of route

Tap this button to see an overview of the route using the map browser.

Show route

summary

Tap this button to open the route summary screen.

Driving View4.

14

Driving View

When your TomTom RIDER starts, you are shown the Driving View along with

detailed information about your current location.

Tap the centre of the screen at any time to open the Main Menu.

Note: The Driving View is shown in black and white until your RIDER locates

your current position.

A Tap + and - to zoom in and out.

B Quick menu - switch this on in the Preferences menu.

This is only shown when you use your TomTom RIDER in a car.

C Your current position.

D The name of the next major road or road sign information, if applicable.

E Navigation instruction for the road ahead.

Tap this area to repeat the last spoken instruction and to change the

volume.

F The name of the street you are on.

G Information about your journey such as journey time, remaining distance

and arrival time.

To change the information shown, tap Status bar preferences in the

Preferences menu.

H Traffic bar. Requires a Bluetooth®-enabled mobile phone. For more

information about how to subscribe to and receive TomTom Traffic, go to

tomtom.com/traffic.

To set up Traffic information, tap TomTom Traffic in the Main Menu.

Menus5.

15

Menus

Main menu

Tap the screen at any time when TomTom RIDER displays the Driving View to

open the Main Menu.

• Navigate to...

Tap this button to start planning a route.

• Find alternative...

Tap this button if you want to avoid part of your route, travel via a specific

location or calculate an alternative route.

• Help me!

Help me! provides an easy way for you to find and contact emergency

service centres and other specialist services.

• Mobile phone

This button opens the mobile phone menu. You can, for example, make

calls, and write or read messages.

• Change preferences

This button opens the Preferences menu. You can change many things

about the way TomTom RIDER looks and behaves.

Hidden buttons and features

When you first start using your TomTom RIDER, not all the buttons will be

shown in the menu.

Many buttons and some more advanced features are hidden because you will

not need these features very often.

To show all buttons and features, tap Show ALL menu options in the

Preferences menu.

16

To hide these buttons again, tap Show fewer menu options in the Preferences

menu.

Safety Driving Menu

If you tap the screen when you are riding, the Safety Driving Menu is shown.

When you use your RIDER in a car, this menu is not shown.

• Navigate to…

Tap this button to select a destination.

• Turn off sound / Turn on sound

Tap this button to turn the spoken instructions on or off.

• Clear route

Tap this button to delete the route that is currently planned. The Driving

View still shows your position.

• Add favourite

Tap this button to add your current location as a favourite. Your

TomTom RIDER uses the address of your current location as the name of

the favourite. You can change the name of the favourite at any time by

tapping Manage favourites in the Preferences menu.

Customise the Safety Driving Menu

You can change the Add favourite button to another button that is more useful

for you. In the Preferences menu, tap Safety driving menu then select the

button to show here.

Finding alternative routes6.

17

Finding alternative routes

Once you have planned a route, you may want to change something about the

route, without changing your destination.

Why change the route?

Maybe for one of these reasons:

• You can see a roadblock or a line of traffic ahead.

• You want to travel via a particular location, to pick someone up, stop for

lunch or fill up with petrol.

• You want to avoid a difficult junction or a road you don’t like.

Find alterna-

tive...

Tap Find alternative... in the Main Menu to change the route that is

currently planned.

Then tap one of the options below.

Calculate

alternative

Tap this button to calculate an alternative to the route already planned.

Your RIDER will look for another route from your current location to your

destination.

If you decide you would prefer to use the original route after all, tap

Recalculate original.

Why would I need to do this?

Apart from the roads near your position and near your destination, the new

route will use totally different roads to reach your destination. This is an

easy way of calculating a totally different route.

Avoid

roadblock

Tap this button if you can see a roadblock or a line of traffic ahead. You then

have to choose how much of the route ahead you want to avoid.

Choose from the different options: 100m, 500m, 2000m, 5000m. Your

RIDER will recalculate your route avoiding the section of the route for the

distance you selected.

Don’t forget that once a new route is calculated, you may have to turn off

the road you are on very soon.

If the roadblock suddenly clears, tap Recalculate original to return to your

original route.

18

Travel via...

Tap this button to change your route so that it passes a particular location,

perhaps to pick someone up on the way.

You choose the location you want to pass in the same way as you choose a

destination. So you can select from all the same options: for example,

Address, Favourite, Point of Interest and Point on map.

Your RIDER will calculate a new route to your destination that passes the

location you chose. Unlike your final destination, your RIDER does not

inform you when you pass by this location.

Using this button, you can only travel via one location. If you want to pass

more than one, use an Itinerary.

Recalculate

original

Tap this button to return to the original route without deviations to avoid

roadblocks or travelling via particular locations.

Avoid part of

route

Tap this button to avoid a part of the route. Use this button if you see that

your route includes a road or junction you don’t like, or which is well-

known for traffic problems.

You then choose the road you want to avoid from a list of the roads on your

route.

Minimise

delays

Tap this button to recalculate your route so that it avoids traffic problems as

much as possible. Your RIDER will check if there are any traffic problems on

your route and work out the best route to avoid the problems.

Note: This button is only available with TomTom Traffic enabled.

Browse Map7.

19

Browse Map

To look at the map in the same way as you might look at a traditional paper

map, tap Browse map in the Main Menu.

You can move the map by touching the screen and moving your finger across

the screen.

A The scale bar

B Your current position.

C GPS button

Tap this button to centre the map on your current position.

D Options

E The cursor

F The Find button

Tap this button to find specific addresses.

G The Cursor button

Tap this button to navigate to the cursor position, make a Favourite of the

cursor position, or find a Point of Interest near the cursor position.

H The zoom bar

Zoom in and out by moving the slider.

Cursor button

You can use the cursor to find addresses and Points of Interest (POIs), for

example, restaurants, train stations and petrol stations.

20

Position the cursor over a location on the map, then tap one of the following

buttons:

Navigate

there

Tap this button to navigate to the cursor position. Your RIDER will calculate

the route.

Find POI

nearby

Tap this button to find a POI near the cursor position. For example, if you

have found a restaurant to go to, you can search for a parking garage

nearby.

Centre on

map

Tap this button to bring the location currently highlighted by the cursor to

the centre of the screen when looking at the map.

Call...

Tap this button to call the location at the cursor position. This button is only

available if your RIDER has the phone number for the location.

The phone numbers of many POIs are stored in your RIDER. If you enter

phone numbers for POIs that you create, you can also call them.

Add as

Favourite

Tap this button to create a Favourite at the cursor position.

Add as POI

Tap this button to create a POI at the cursor position.

Correct

location

Tap this button to correct the location shown at the cursor position.

La pagina sta caricando ...

TomTom RIDER 2 Manuale del proprietario

TomTom RIDER 2 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti