Ariens 924126-ST11526DLE Manuale utente

Categoria
Spazzaneve
Tipo
Manuale utente
Owner/Operator Manual
Models
924124 ST926DLE
924125 ST11528LE
924126 ST11526DLE
924127 ST11528DLE
924128 ST1332LE
924335 ST926DLE
924336 ST11526DLE
924337 ST11528DLE
924338 ST1332LE
924516 ST1332DLE
924517 ST1336DLE
Sno-Thro®
00294700A 12/04
Supersedes 00294700
Printed in USA
ENGLIS
H
FRANÇAI
S
ESPAÑO
L
Transfer
model &
serial number
label from
product
registration
here.
Coller l’autocollant du
modèle et du numéro de
série dans cet encadré.
Transferir aquí la etiqueta
del modelo y número de
serie del registro del
producto.
2
Ariens Company
655 West Ryan Street
P.O. Box 157
Brillion, Wisconsin
54110-0157 USA
Telephone
(920) 756-2141
Facsimile
(920) 756-2407
EC DECLARATION OF CONFORMITY ISSUED BY THE MANUFACTURER
DÉCLARATION DE CONFORMITÉ CE ÉMISE PAR LE FABRICANT –
EU-ÜBEREINSTIMMUNGSERKLÄRUNG DES HERSTELLERS –
DICHIARAZIONE DI CONFORMITÀ CE RILASCIATA DAL PRODUTTORE –
DECLARACIÓN DE CONFORMIDAD CE EMITIDA POR EL FABRICANTE –
EF-SAMSVARSERKLÆRING FRA PRODUSENTEN –
EG-DEKLARATIONEN OM ÖVERENSSTÄMMELSE UTFÄRDAD
AV TILLVERKAREN –
VALMISTAJAN ANTAMA EY-VAATIMUSTENMUKAISUUSVAKUUTUS –
DEKLARACJA ZGODNOŚCI Z PRZEPISAMI EC WYDANA PRZEZ
PRODUCENTA –
We the undersigned, ARIENS COMPANY, certify that: Nous, soussignés ARIENS COMPANY, certifions
que : Der Unterzeichnete, ARIENS COMPANY, bescheinigt, dass: La sottoscritta società ARIENS
COMPANY certifica che: Nosotros, los abajo firmantes, ARIENS COMPANY, certificamos que:
Undertegnede, ARIENS COMPANY, bekrefter at: Undertecknad, ARIENS COMPANY, intygar att:
Allekirjoittanut, ARIENS COMPANY, vakuuttaa, että: My, niźej podpisani, ARIENS COMPANY,
oświadczamy, że:
Type: Type : Typ:
Tipo: Tipo: Type:
Typ: Tyyppi: Typ:
WALK BEHIND SNOW THROWER – LES CHASSES-NEIGE AUTOTRACTÉS –
HANDGEFÜHRTE SCHNEEFRÄSE – SPAZZANEVE SEMOVENTE –
CAMINAR POR DETRÁS DE LA LANZADORA DE NIEVE – SNØFRESER –
SJÄLVGÅENDE SNÖSLUNGA – KÄSINOHJAILTAVA LUMILINKO –
ODGARNIACZ ŚNIEGU DO PROWADZENIA PRZED SOBĄ
Trade Name: Appellation commerciale : Handelsbezeichnung: Nome
commerciale: Nombre comercial: Handelsnavn: Handelsbeteckning:
Kauppanimi: Nazwa handlowa:
Ariens
Model: Modèle : Modell: Modello: Modelo: Modell: Modell: Malli: Model:
924335,
924336,
924337,
924338,
924516,
924517
Conforms to: Est conforme à : Mit den Anforderungen der folgenden Richtlinien übereinstimmt:
È conforme a: Cumple con: Er i samsvar med: Överensstämmer med: Täyttää seuraavat
vaatimukset: Jest zgodny z:
98/37/EC, 89/336/EEC,
2000/14/EC Conformity Assessment Annex V. Annexe V de l'évaluation de conformité.
Konformitätsbewertung, Anhang V. Annesso V della valutazione di conformità. Anexo V
de la evaluación de la conformidad. Samsvarsvurdering etter vedlegg V. Bedömning av
överensstämmelse Bilaga V. Vaatimustenmukaisuuden arviointi, liite V. Dodatek V, Ocena zgodności.
3
CE Sound and Vibration – Niveau sonore et vibration CE – CE-Geräuschpegel
und Vibrationswerte – Livello sonoro e vibrazioni CE – Sonido y vibración CE –
CE-lydnivå og Vibrasjonsmåling – CE ljudnivå och Vibrations-mätning – CE-
melutaso Tärinä – CE DŸwiêku i Wibracji
Representative Measured Sound Power Level (L
wa
) –
Niveau de puissance acoustique représentatif mesuré
(L
wa
) – Repräsentativer gemessener Geräuschpegel
(L
wa
) – Livello di potenza sonora rappresentativo rilevato
(L
wa
) – Nivel de potencia acústica representativo
medido (L
wa
) – Representativt målt lydeffektnivå (L
wa
) –
Representativ uppmätt ljudnivå (L
wa
) – Tyypillinen mitattu
äänitehotaso (L
wa
) – Zmierzony reprezentatywny poziom
mocy akustycznej (L
wa
) –
Guaranteed Sound Power Level (L
wa
) –
Niveau de puissance acoustique garanti (L
wa
) –
Garantierter Geräuschpegel (L
wa
) – Livello di potenza
sonora garantito (L
wa
) – Nivel de potencia acústica
garantizado (L
wa
) – Garantert lydeffektnivå (L
wa
) –
Garanterad uppmätt ljudnivå (L
wa
) – Taattu
äänitehotaso (L
wa
) – Gwarantowany reprezentatywny
poziom mocy akustycznej (L
wa
) –
924335, 338, 516, 517:
924337, 924336:
106 dB
A
108 dB
A
924335, 338, 516, 517:
924337, 924336:
110 dB
A
112 dB
A
Philip J. Smucker:
Quality and Conformance Manager (Keeper of Technical
File) Responsable de la qualité et de la conformité des
produits (Dépositaire de la fiche technique) Manager
Qualitätssicherung und Konformität (Archivar der
technischen Akte) Responsabile della qualità e della
conformità del prodotto (Depositario del file tecnico)
Gerente de calidad y conformidad (Depositario del
archivo técnico) Kvalitet- og samsvarsansvarlig
(innehaver av tekniske data) Chef för kvalitet och
produktöverensstämmelse (Innehavare av tekniska data)
Laadusta ja vaatimustenmukaisuudesta vastaava
päällikkö (Teknisen tiedoston haltija) Kierownik do spraw
jakości i zgodności (Przechowujący Dokumentację
Techniczną)
Ariens Company
Brillion, WI 54110-0157 USA
Signature Signature Unterschrift
Firma Firma Signatur
Namnteckning Allekirjoitus
Podpis
4/19/2004
Date Date Datum
Data Fecha Dato
Datum Päiväys
Data
Model: – Modèle : – Modell: – Modello: –
Modelo: – Modell: – Modell: – Malli: – Model:
924335 924336 924337 924338 924516 924517
Oper. Ear Sound Pressure (L
pa
) in dB
A
Pression acoustique Pression sonore à aux
oreilles de l’opérateur (L
pa
) en dB
A
Geräuschstärke am Ohr des Bedieners (L
pa
)
in dB
A
– Potenza sonora percepita
dall’operatore
(L
pa
) in. dB
A
– Presión de sonido en el oído
(L
pa
) in dB
A
– Lydtrykk i førerens øre (L
pa
) in.
dB
A
– vid förarens position (L
wa
) i dB
A
Kuljettajan korvaan kohdistuva äänipaine
(L
pa
)/dB
A
Robocze ciśnienie akustyczne na
uchu (L
pa
) w decybelach
A
93 94 94 93 93 93
Vibration Measure (m/sec
2
) @ Operator
Hands – Niveau de vibrationaux mains de
l’opérateur – Vibrationswerte An den Händen
des Bedieners – Misura delle vibrazioni alle
mani dell’operatore – Cantidad de vibración
en las manos del operador –
Vibrasjonsmåling ved brukerens hender –
Vibrationsmätning vid förarens händer –
Tärinä kuljettajan käsissä – Pomiar wibracji
(m/sec
2
) na rękach operatora
X 1.9 2.5 3.2 1.7 1.7 2.8
Y 5.8 4.1 3.9 4.0 4.0 4.4
Z 7.0 7.2 7.7 4.2 4.2 5.3
GB - 4
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Controls and Features . . . . . . . . . . . . . . . 13
Operation. . . . . . . . . . . . . . . . . . . . . . . . . . 14
Maintenance . . . . . . . . . . . . . . . . . . . . . . . 19
Service and Adjustments. . . . . . . . . . . . . 21
Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Service Parts . . . . . . . . . . . . . . . . . . . . . . . 27
Accessories. . . . . . . . . . . . . . . . . . . . . . . . 27
Troubleshooting . . . . . . . . . . . . . . . . . . . . 28
Specifications . . . . . . . . . . . . . . . . . . . . . . 29
Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . 31
THE MANUAL
Before operation of unit, carefully and
completely read your manuals. If used
improperly, this unit could be dangerous and
cause personal injury or property damage.
The contents will provide you with safety
instructions for the safe use of your unit during
normal operation and maintenance.
All reference to left, right, front, or rear are
given from operator standing in operation
position and facing the direction of forward
travel.
MODEL AND SERIAL NUMBERS
When ordering replacement parts or making
service inquiries, know the Model and Serial
numbers of your unit and engine.
Numbers are located on the product
registration form in the unit literature package.
They are printed on a serial number label,
located on the frame of your unit.
Record Unit Model and Serial numbers
here.
Record Engine Model and Serial number
here.
PRODUCT REGISTRATION
The Ariens dealer must register the product at
the time of purchase. Registering the product
will help the company process warranty claims
or contact you with the latest service
information. All claims meeting requirements
during the limited warranty period will be
honored, whether or not the product
registration card is returned. Keep a proof of
purchase if you do not register your unit.
Customer Note: If the dealer does not
register your product, please fill out, sign, and
return the product registration card to Ariens
or go to www.ariens.com.
UNAUTHORIZED REPLACEMENT
PARTS
Use only Ariens replacement parts. The
replacement of any part on this vehicle with
anything other than an Ariens authorized
replacement part may adversely affect the
performance, durability, or safety of this unit
and may void the warranty. Ariens disclaims
liability for any claims or damages, whether
warranty, property damage, personal injury or
death arising out of the use of unauthorized
replacement parts.
For a brief list of replacement parts see
Service Parts in this manual. To obtain a
complete parts manual, find your model and
serial number. Then go to www.ariens.com or
call 1-920-756-4664.
DISCLAIMER
Ariens reserves the right to discontinue, make
changes to, and add improvements upon its
products at any time without public notice or
obligation. The descriptions and specifications
contained in this manual were in effect at
printing. Equipment described within this
manual may be optional. Some illustrations
may not be applicable to your unit.
TABLE OF CONTENTS
INTRODUCTION
Serial Number
Label
OS6720
Figure 1
© Copyright 2004 Ariens Company
GB - 5
DELIVERY
Customer Note: If you have purchased this
product without complete assembly and
instruction by your retailer, it is your
responsibility to:
1. Read and understand all assembly
instructions in this manual. If you do not
understand or have difficulty following the
instructions, contact your nearest Ariens
Dealer for assistance. Make sure all
assembly has been properly completed.
NOTE: To locate your nearest Ariens Dealer,
call 1-920-756-4664 or go to www.ariens.com
on the internet.
2. Understand all Safety Precautions
provided in the manuals.
3. Review control functions and operation of
the unit. Do not operate the Sno-Thro
unless all controls function as described
in this manual.
4. Review recommended lubrication,
maintenance and adjustments.
5. Review Limited Warranty Policy.
6. Fill out a Product Registration Card and
return the card to the Ariens Company or
go to www.ariens.com.
SAFETY ALERTS
Look for these symbols to point
out important safety precautions.
They mean:
Attention!
Personal Safety Is
Involved!
Become Alert!
Obey The Message!
The safety alert symbols above and signal
words below are used on decals and in this
manual. Read and understand all safety
messages.
NOTATIONS
NOTE: General reference information for
proper operation and maintenance practices.
IMPORTANT: Specific procedures or
information required to prevent damage to unit
or attachment.
PRACTICES AND LAWS
Practice usual and customary safe working
precautions, for the benefit of yourself and
others. Understand and follow all safety
messages. Be alert to unsafe conditions and
the possibility of minor, moderate, or serious
injury or death. Learn applicable rules and
laws in your area. Always follow the practices
set forth in this manual.
REQUIRED OPERATOR TRAINING
Original purchaser of this unit was instructed
by the seller on safe and proper operation. If
unit is to be used by someone other than
original purchaser; loaned, rented or sold,
ALWAYS provide this manual and any needed
safety training before operation.
WARNING: Improper assembly or
adjustments can cause serious injury.
SAFETY
WARNING: To avoid injury to hands
and feet, always disengage clutches,
shut off engine, and wait for all
movement to stop before unclogging
or working on snow thrower.
Hand contact with the rotating impeller
is the most common cause of injury
associated with snow throwers. Never
use your hand to clean out the
discharge chute.
Keep hands and feet away from auger
and impeller.
DANGER: IMMINENTLY
HAZARDOUS SITUATION! If not
avoided, WILL RESULT in death or
serious injury.
WARNING: POTENTIALLY
HAZARDOUS SITUATION! If not
avoided, COULD RESULT in death or
serious injury.
CAUTION: POTENTIALLY
HAZARDOUS SITUATION! If not
avoided, MAY RESULT in minor or
moderate injury. It may also be used to
alert against unsafe practices.
GB - 6
SAFETY DECALS AND
LOCATIONS
ALWAYS replace missing or damaged Safety
Decals. Refer to figure below for Safety Decal
locations.
1. DANGER!
2. WARNING!
3. DANGER!
SAFETY RULES
Read, understand, and follow all safety
practices in Owner/Operator Manual before
beginning assembly or operating. Failure to
follow instructions could result in personal
injury and/or damage to unit.
ALWAYS remove key and/or wire from spark
plug before assembly, maintenance or service.
Unintentional engine start up can cause death
or serious injury.
Complete a walk around inspection of unit and
work area to understand:
• Work area • Your unit • All safety decals
ALWAYS check overhead and side clearances
carefully before operation. ALWAYS be aware
of traffic when operating along streets or
curbs.
Keep children and people away. Keep children
out of work area and under watchful care of a
responsible adult.
NEVER allow children to operate or play on or
near unit. Be alert and shut off unit if children
enter area.
DO NOT allow adults to operate unit without
proper training.
ROTATING PARTS.
Keep clear of auger while engine
is running.
Read Operator’s Manual.
Allow operation only by
properly trained adult, never
children.
Stop engine and remove
ignition key prior to leaving
the operator’s position for any
reason.
Keep all controls, guards and
safety devices properly
serviced and functional.
Never direct discharge
towards persons or property
that may be injured or
damaged by thrown objects.
Read Owner/Operator Manual.
Keep people away from unit while
operating. Keep children out of
work area and under watchful
care of a responsible adult.
OS6600
1
2
3
Figure 2
OS2080
OL1801
Never direct discharge towards
persons or property that may be
injured or damaged by thrown
objects.
Stop engine, remove key, read
manual before making any
repairs, adjustments.
Wear appropriate hearing
protection.
ONLY use clean-out tool to clear
blockages. NEVER use your
hands.
ROTATING PARTS! ONLY use
clean-out tool to clear blockages.
NEVER use your hands. High
speed impeller rotates below
discharge opening. Wait for all
moving parts to stop before
removing clogs or servicing.
OL0910
OS6610
GB - 7
Keep area of operation clear of all toys, pets,
and debris. Thrown objects can cause injury.
Check for weak spots on docks, ramps or
floors. Avoid uneven work areas and rough
terrain. Stay alert for hidden hazards.
Avoid uneven and rough terrain. DO NOT
operate near drop-offs, ditches, or
embankments. Unit can suddenly turn over if a
wheel is over the edge of a cliff or ditch, or if
an edge caves in.
Falling snow, fog, etc. can reduce vision and
cause an accident. Operate unit only when
there is good visibility and light.
Only trained adults may operate unit.
Training includes actual operation.
NEVER operate unit after or during the use of
medication, drugs or alcohol. Safe operation
requires your complete and unimpaired
attention at all times.
NEVER allow anyone to operate this unit
when their alertness or coordination is
impaired.
DO NOT operate unit without wearing
adequate winter outer garments. Wear
adequate safety gear, including safety glasses
with side shields, and protective gloves. Wear
proper footwear to improve footing on slippery
surfaces.
DO NOT wear loose clothing or jewelry and tie
back hair that may get caught in rotating parts.
Protect eyes, face and head from objects that
may be thrown from unit. Wear appropriate
hearing protection.
Avoid sharp edges. Sharp edges can cut.
Moving parts can cut off fingers or a hand.
ALWAYS keep hands and feet away from all
rotating parts during operation. Rotating parts
can cut off body parts.
NEVER place your hands or any part of your
body or clothing inside or near any moving
part while unit is running.
ALWAYS keep hands away from all pinch
points.
DO NOT touch unit parts which might be hot
from operation. Allow parts to cool before
attempting to maintain, adjust or service.
Never direct discharge towards persons or
property that may be injured or damaged by
thrown objects. Use extreme caution on gravel
surfaces. Stay alert for hidden hazards or
traffic. Adjust Runners so Scraper Blade does
not contact gravel.
DO NOT throw snow any higher than
necessary.
Deflected materials can cause injury and
property damage.
Always stand clear of the discharge area when
operating this unit.
Fumes from engine exhaust can cause injury
or death. DO NOT run engine in an enclosed
area. Always provide good ventilation.
ALWAYS disengage attachment, stop unit and
engine, remove key and allow moving parts to
stop before leaving operator’s position.
ROTATING IMPELLER CAN CAUSE
SERIOUS INJURY. NEVER ATTEMPT TO
UNCLOG OR CLEAN UNIT WHILE ENGINE
IS RUNNING.
Read, understand, and follow all instructions in
the manual and on the machine before
starting.
Understand:
How to operate all controls.
The functions of all controls.
How to STOP in an emergency.
Before starting engine, disengage control(s).
Use only approved extension cords and
receptacles when starting units equipped with
electric starter. DO NOT connect electric
starter cord to any wiring system that is not a
three-wire grounded system.
ALWAYS allow unit and engine to adjust to
outdoor temperatures before clearing snow.
Always be sure of your footing, especially
when operating in reverse or leaving the
operator’s position. Walk, never run during
operation.
DO NOT overload the machine capacity by
attempting to clear snow at too fast a rate.
DO NOT operate at too fast a rate.
Slow down and turn corners slowly.
Do not operate in reverse unless absolutely
necessary. ALWAYS back up slowly. Always
look down and behind before and while
backing.
Disengage attachment drive when traveling
from one work area to another.
Abnormal Vibrations are a warning of trouble.
Striking a foreign object can damage unit.
Immediately stop unit and engine. Remove
key and wait for all moving parts to stop.
Remove wire from spark plug. Inspect unit and
make any necessary repairs before restart.
GB - 8
Before cleaning, removing clogs or making
any inspections, repairs, etc.: disengage
clutch(es), stop unit and engine, remove
key, allow moving parts to stop. Allow hot
parts to cool.
Run unit a few minutes after clearing snow to
prevent freeze-up of attachment.
Disengage attachment when not in use.
Disengage all clutches before starting engine.
Adjust runners to clear gravel or crushed rock
surfaces safely.
Never leave a running unit unattended.
ALWAYS shut off engine before leaving unit.
ALWAYS remove key to prevent unauthorized
use.
Never carry passengers.
Check clutch and brake operation frequently.
Adjust and service as required. All motion of
drive wheels and auger/impeller must stop
quickly when control levers are released.
DO NOT operate on steep slopes. DO NOT
clear snow across the face of slopes. Keep all
movement on slopes slow and gradual. DO
NOT make sudden changes in speed or
direction. Use a slow speed to avoid stops or
shifts on slopes. Avoid starting or stopping on
a slope.
DO NOT park unit on a slope unless
absolutely necessary. When parking on a
slope always block the wheels.
ALWAYS shut off engine, remove key, and
close fuel shut-off valve or drain fuel when
transporting unit on a truck or trailer.
Use extra care when loading or unloading unit
onto trailer or truck.
Secure unit chassis to transport vehicle.
NEVER secure from rods or linkages that
could be damaged.
DO NOT transport machine while engine is
running.
Keep unit free of ice or other debris. Clean up
oil or fuel spills.
This product is equipped with an internal
combustion type engine. DO NOT use unit on
or near any unimproved, forest-covered or
brush covered land unless exhaust system is
equipped with a spark arrester meeting
applicable local, state or federal laws. A spark
arrester, if it is used, must be maintained in
effective working order by operator.
Fuel is highly flammable and its vapors are
explosive. Handle with care. Use an approved
fuel container.
NO smoking, NO sparks, NO flames. ALWAYS
allow engine to cool before servicing.
NEVER fill fuel tank when engine is running or
hot from operation.
NEVER fill or drain fuel tank indoors.
Replace fuel cap securely and clean up spilled
fuel.
Never fill containers inside a vehicle or on a
truck or trailer bed with a plastic liner. Always
place containers on the ground away from
your vehicle before filling.
When practical, remove gas-powered
equipment from the truck or trailer and refuel it
on the ground. If this is not possible, then
refuel such equipment on a trailer with a
portable container, rather than from a gasoline
dispenser nozzle.
Keep the nozzle in contact with the rim of the
fuel tank or container opening at all times until
fueling is complete. Do not use a nozzle
lock-open device.
If fuel is spilled on clothing, change clothing
immediately.
Avoid Electric Shock. Objects contacting both
battery terminals at the same time may result
in injury and unit damage. DO NOT reverse
battery connections.
Explosive Gases from battery can cause death
or serious injury. Poisonous battery fluid
contains sulfuric acid and its contact with skin,
eyes or clothing can cause severe chemical
burns.
No flames, No sparks, No smoking near
battery.
ALWAYS wear safety glasses and protective
gear near battery.
DO NOT TIP battery beyond a 45° angle in
any direction.
ALWAYS keep batteries out of reach of
children.
Battery posts, terminals and related
accessories contain lead and lead
compounds, chemicals known to the State of
California to cause cancer and reproductive
harm. Wash hands after handling.
Follow First Aid directions for contact with
battery fluid.
External Contact: Flush with water.
Eyes: Flush with water for at least 15
minutes and get medical attention
immediately!
Internal Contact: Drink large quantities of
water. Follow with Milk of Magnesia,
beaten egg or vegetable oil. Get medical
attention immediately!
GB - 9
In case of internal contact, DO NOT
induce vomiting!
Before tipping unit up onto housing, remove
fuel so no spills will occur and remove battery.
Ensure unit is secure and will not tip over
during maintenance.
ALWAYS keep protective structures, guards,
and panels in good repair, in place and
securely fastened. NEVER modify or remove
safety devices.
DO NOT change engine governor settings or
over-speed engine.
Fumes from engine exhaust can cause injury
or death. DO NOT run engine in an enclosed
area. Always provide good ventilation.
ALWAYS maintain unit in safe operating
condition. Damaged or worn out muffler can
cause fire or explosion.
Keep all hardware properly tightened. Check
shear bolts frequently.
Maintain or replace safety and instruction
labels, as necessary.
NEVER store unit with fuel in fuel tank, inside
a building where any ignition sources are
present such as hot water heaters, space
heaters, or clothes dryers. Allow the engine to
cool before storing in any enclosure.
Shut off fuel and allow engine to cool
completely before storing in closed area or
covering unit.
For extended storage, clean unit thoroughly.
See Engine Manual for proper storage.
Use only attachments or accessories designed
for your unit.
Check components frequently. If worn or
damaged, replace with manufacturer’s
recommended parts.
Tools Required:
Pliers
Open-End Wrenches: 3/8, 7/16, 1/2, 9/16"
and/or Adjustable Wrench
Tire Gauge
PACKAGE CONTENTS
ASSEMBLY
Handlebar and Shift Rod
1. Remove lower wing knobs on handlebar
assembly (Figure 4).
2. Remove upper wing nut and bolt on shift
rod.
3. Loosen upper wing knobs on handlebar.
4. Loosen lower wing nut and bolt on shift
rod.
5. Put speed selector lever into fastest
reverse panel notch.
6. Rotate handlebar up so wing knob holes
align. Install and tighten all wing knobs.
7. Install wing nut and bolt removed in step 2
on shift rod and tighten hardware.
ASSEMBLY
WARNING: AVOID INJURY. Read
and understand the entire Safety
section before proceeding.
WARNING: Dropping or tipping over
boxed unit could result in personal
injury or damage to unit.
Figure 3
OS1642
1.Sno-Thro Unit
2.Chute Crank
(Not on 924517)
3.Discharge Chute
4.Literature Pack
with Extra Shear
Bolts
1
2
3
4
GB - 10
Install Discharge Chute (924124-128,
335-338, 516)
Figure 5.
1. Grease underside of discharge chute ring
(if not already greased).
2. Remove mounting hardware from auger
housing.
3. Install discharge chute over opening in the
auger housing and secure pedestal to
auger housing with hardware removed in
step 2.
Install Discharge Chute Crank
1. Slide chute crank rod through the opening
in control panel, through the upper hole in
the bracket under panel and out the hole
in the front panel.
2. Align chute crank rod with the pinion gear
or universal joint (if so equipped) on chute
and fasten with spring clip.
Install Discharge Chute (924517)
1. Remove chute motor cover from chute
motor (Figure 7).
1.Handlebar
Assembly
2.Wing Knobs
3.Wing Nut
4.Speed Selector
5.Bolt
6.Shift Rod
1
2
4
5
6
Figure 4
3
OS3020
2
Figure 5
1.Mounting
Hardware
2.Discharge
Chute
3.Chute Pedestal
4.Discharge
Chute Ring
1
1
3
2
OS6610
OS6620
4
Figure 6
1.Spring Clip
2.Chute Crank Rod
1
OS000
1
2
GB - 11
2. Turn the chute gear until the solid pin is
towards the rear of the unit and a
threaded stud aligns with the chute motor
(Figure 7).
3. Remove the six (6) nuts and two half rings
(Figure 7).
4. Make sure the three (3) chute clamps on
the chute gear are underneath the
discharge chute flange as shown in
(Figure 8)
5. Install discharge chute on blower housing
with the opening of the discharge chute
facing towards the front of the unit (Figure
9).
6. Install two (2) half rings on unit with six (6)
nuts. Tighten nuts to 120 lbf-in.
(13.56 N•m) (Figure 9).
7. Install chute motor cover on chute motor
(Figure 9).
Figure 7
1
6
7
5
2
4
3
1.Solid Pin
2.Threaded Stud
3.Chute Motor
4.Chute Motor
Cover
5.Chute Ring
6.Nut
7.Half Ring
Figure 8
1
5
2
4
3
1.Chute Clamp
2.Chute Gear
3.Discharge Chute
Flange
Correct Chute Clamp Orientation
Incorrect Chute Clamp Orientation
Figure 9
1
2
3
1.Discharge Chute
2.Half Ring
3.Nut
4.Chute Motor
Cover
4
GB - 12
Connect Battery (924516, 517)
1. Remove wing nuts from battery cover.
2. Install wire lead to battery terminal.
3. Install battery cover and tighten wing nuts.
Deflector Remote
1. Remove e-ring and flat washer from stud
on discharge chute.
2. Route deflector remote cable between the
engine and the chute pedestal.
3. Slide cable end through hole on bracket on
left side of chute (Figure 10).
4. Attach cable eye to stud on deflector. Hold
in place with flat washer and e-ring.
5. Check deflector travel. Adjust nut on cable
end under handlebar to obtain full travel.
(See Deflector Remote in Service and
Adjustments.)
Check Function of Dual Handle
Interlock
Without the engine running, press down
(engage) both clutch levers. Release
attachment clutch lever. Attachment clutch
should remain engaged until traction clutch
lever is released, then both clutches must
disengage. If they do not, contact your dealer
for repairs.
Check Tire Pressure
Check tire pressure and adjust to the pressure
listed on tire sidewall.
Check Auger Gearcase Oil
Check oil level in auger gearcase (see Service
and Adjustments).
Check Engine Crankcase Oil
IMPORTANT: The engine is shipped with
5W-30 oil in crankcase. Refer to Engine
Manual for detailed instructions.
Fill Engine Fuel Tank
Refer to Engine Manual for proper fuel type
and tank capacity.
Check Function of all Controls
Ensure unit runs and performs properly. Refer
to Operation.
Run-in Attachment Belt
1. Start unit in a well-ventilated area
according to Starting and Shut-Off in
Operation.
2. Engage attachment clutch lever and run
attachment for about 15 minutes.
3. Stop unit, wait for all moving parts to stop,
and remove spark plug wire.
4. Adjust belt finger, if necessary. See
Attachment Drive Belt Replacement on
page 25.
5. Adjust clutch according to Attachment
Clutch/Brake Adjustment in Service and
Adjustments.
Figure 10
1.Cable Eye
2.Flat Washer and E-Ring
3.Deflector Cable
1
2
3
GB - 13
1. Traction Drive Clutch Lever
2. Oil Fill/Dipstick
3. Muffler Guard
4. Belt Cover
5. Discharge Chute Deflector
6. Discharge Chute
7. Electric Chute Motor
8. Impeller
9. Clean-out Tool
10. Auger Gearcase
11. Scraper Blade
12. Auger
13. Recoil Starter Handle
14. Primer Bulb
15. Choke Control Knob
16. Throttle (Engine Stop)
17. Oil Drain Plug
18. Attachment Clutch Lever
19. Heated Handles
20. Deflector Remote Control
21. Heated Handles Switch
22. Speed Selector
23. Ignition Key (924516, 517)
24. Chute Crank (Not on 924517)
25. Differential Lock (924124, 126, 127, 335,
336, 337, 516, 517)
26. Chute Rotation Switch (924517)
27. Ignition Key, push-pull (924124, 125, 126,
127, 128, 335, 336, 337, 338)
28. Runner
29. Drift Cutter
30. Axle Lock Pin (924125, 128, 338)
31. Battery Cover and Battery (924516, 517)
32. Solenoid Compartment (924516, 517)
33. Fuel Shut-Off Valve
34. Electric Starter (924124, 125, 126, 127,
128, 335, 336, 337, 338)
35. Wing Knobs
36. Fuel Tank and Cap
37. Headlight
CONTROLS AND FEATURES
Figure 11
1
15
13
14
16
17
18
20
22
23
24
1
29
31
32
3
27
8
9
10
5
25
21
28
12
2
11
35
36
37
34
19
19
30
33
4
26
6
7
GB - 14
CONTROLS AND FEATURES
See Figure 11 for all Controls and Features
locations.
Dual Handle Interlock
When Attachment Clutch and then Traction
Drive Clutch are engaged, the Attachment
Clutch will remain engaged (lever down) if
released. To stop attachment, release Traction
Drive Clutch and both clutches will disengage.
Traction Drive Clutch - Left Hand
Lever
Squeeze the Traction
Drive Clutch Lever
against the Handlebar
(1) to engage wheel
drive for propelling unit.
Forward speed will vary
according to snow depth
and moisture content.
Release lever (2) to
stop movement.
NOTE: When traveling to or from the area to
be cleared, press down on the handlebars
enough to raise the front of the unit slightly off
the surface. Engage the traction drive clutch
without engaging the attachment drive clutch.
Attachment Clutch - Right Hand Lever
Squeeze Attachment
Clutch Lever against
handlebar (1) to engage
attachment. Release
both clutch levers (2) to
disengage power and
apply brake to
attachment.
IMPORTANT: If the belt squeals when the
attachment clutch lever is engaged, the
attachment drive may be frozen. Immediately
release the attachment clutch lever and move
the unit into a heated area to thaw.
Ignition Switch (120V or 240V start on
engine)
Key Switch has two positions:
1. “Stop” - pulled out
2. Run - pushed in
NOTE: DO NOT twist key after
it is inserted.
Ignition Switch (12V start on dash
panel)
The ignition switch is
operated by a removable key.
It has three positions:
1. Stop
2. Run
3. Start
Primer Bulb
Pushing the primer bulb in adds
fuel for easier engine start.
Refer to Starting and Shut Off.
Speed Selector
The Speed Selector controls the unit travel in a
forward or reverse direction when positioned
in notch of speed.
Forward:
(6) Fastest
(1) Slowest
Reverse:
(1) Slow
(2) Fast
IMPORTANT: DO NOT
change motion from
forward to reverse with
clutch engaged.
Forward speed can be
changed without
declutching.
OPERATION
WARNING: AVOID INJURY. Read
and understand the entire Safety
section before proceeding.
WARNING: To avoid injury to hands
and feet, always disengage clutches,
shut off engine, and wait for all
movement to stop before unclogging
or working on snow thrower.
Keep hands and feet away from auger
and impeller.
1
2
OL2701
1
2
OL2691
1
2
OS1431
OS023
2
1
2
3
OS1321
OS1192
1
2
6
5
4
3
2
1
GB - 15
Choke Control Knob
1. Choke Closed position:
chokes off air to engine for
easier start.
2. Choke Open position:
allows for normal
operation.
IMPORTANT: Gradually
open choke after engine
starts.
Throttle
The throttle controls the engine
speed. To increase or decrease
the engine speed, adjust to:
1. Fast (normal or warm starts)
2. Part-Throttle
3. Slow (cold weather starts)
4. Stop (engine is off)
Electric Starter
The electric starter will start a properly choked
and cranked engine when the key is turned
(12V) or starter button (120V or 240V) is
pushed. Refer to Starting and Shut-Off.
Recoil Starter Handle
When pulled, handle will turn engine over.
IMPORTANT: DO NOT let handle snap back
against starter.
Snow Clean-Out Tool (Figure 12)
To clear the chute:
1. Shut off the engine.
2. Wait 10 seconds to be sure impeller
blades have stopped rotating.
3. Remove the snow clean-out tool (1) from
the auger housing and use it to remove
the clog.
4. Replace the snow clean-out tool on the
auger housing.
Deflector Remote
Place deflector into position before operation.
DO NOT throw snow any higher than
necessary.
Push deflector remote forward to throw snow
lower. Pull deflector remote back to throw
snow higher.
Discharge Chute
Discharge chute rotates 220°.
ALWAYS position discharge chute in safe
direction and angle, away from operator and
bystanders, before starting engine.
Chute Crank (Not on 924517)
IMPORTANT: If chute does not stay in set
position, adjust as directed in Service and
Adjustments, or repair before operation.
Rotate the Chute with Discharge Chute Crank
Handle.
IMPORTANT: DO NOT force frozen chute
controls. Start engine and run for 3-5 minutes
to thaw. If still frozen, take to warm place until
controls are free.
Chute Rotation Switch (924517)
Press the chute rotation switch right (1) to
rotate chute clockwise. Press the chute
rotation switch left (2) to rotate chute
counterclockwise.
Heated Handles
Turn the heated handles
switch to the ON (1) position
to activate. Turn the switch
to the OFF (2) position to
deactivate.
WARNING: Hand contact with the
rotating impeller is the most common
cause of injury associated with snow
throwers. Never use your hand to
clean out the discharge chute.
1
2
OS1332
STOP
1
2
3
4
OL2720
1
Figure 12
OS1970
12
OS1950
1
2
GB - 16
Differential Lock (924124, 126, 127,
335, 336, 337, 516, 517)
Differential Lock knob is located
on the Left Wheel Hub. With
differential locked power is
applied equally to both wheels.
To engage differential lock:
• Pull and turn knob to LOCKED
(1) position and release (knob
will snap in place when
positioned correctly).
To resume differential action for
transport:
Pull and turn knob to UNLOCKED (2)
position and release.
Axle Lock Pin (Figure 13) (924125, 128,
338)
Use the axle lock pin to lock or unlock the right
wheel. Lock the right wheel to increase
traction; unlock the right wheel to allow for
easier turning of the unit.
Scraper Blade
The scraper blade allows the back of the
housing to keep better contact with the surface
being cleared. It also prevents damage to the
housing from normal wear.
IMPORTANT: DO NOT allow Scraper Blade to
wear too far or Auger/Impeller housing will
become damaged.
Runners
The runners control the distance between the
scraper blade and the ground. Adjust runners
equally to keep blade level with the ground.
Refer to Pre-Start for recommended settings.
Drift Cutters (Figure 14)
Drift cutters break up snow drifts that are taller
than the auger housing and direct the snow
into the auger. Store the drift cutters on the
auger housing when not in use. Install them as
shown below so they are taller than the snow
to be cleared.
1
2
OL2730
Figure 13
Wheel Unlocked
Wheel Locked
Axle
Lock
Pin
1.Stored Position
2.Operating Position
1
2
Figure 14
GB - 17
FILLING FUEL TANK
Fuel Shut-Off Valve
IMPORTANT: The fuel shut-off valve MUST be
in the closed position prior to transporting the
unit.
The fuel shut-off valve has two positions:
Closed Position: Use this position to
service, transport, or store the unit.
Open Position: Use this position to run the
unit.
To add fuel to fuel tank:
1. ALWAYS place unit in open or well-
ventilated area.
2. Stop engine and allow to cool.
3. Clean Fuel Cap and surrounding area to
prevent dirt from entering Fuel Tank.
4. Remove Cap.
IMPORTANT: DO NOT use gasohol or
gasoline containing alcohol. See Engine
Manual for correct type and grade of fuel.
5. Fill fuel tank to within 1/2 in. (1.2 cm)
below bottom of filler neck with unleaded
gasoline.
NOTE: Tank capacity is 1 gallon (3.8 liters).
6. Replace Fuel Cap and tighten.
7. ALWAYS clean up any spilled fuel.
PRE-START
1. Frozen Impeller
IMPORTANT: Before starting engine, check
impeller to be sure it is not frozen.
To check impeller:
1. With key in “Stop” position, squeeze
Attachment Clutch Lever to Engaged
position.
2. Pull Recoil Starter Handle.
3. If Impeller is frozen, (cannot pull Starter
Handle) move unit to a heated area and
thaw to prevent possible damage.
2. Check Dual Handle Interlock
Without the engine running, press down
(engage) both clutch levers. Release
attachment clutch lever. Attachment clutch
should remain engaged until traction clutch
lever is released, then both clutches must
disengage.
If clutches do not engage or disengage
properly, adjust or repair before operation (see
Service and Adjustments).
3. Differential Lock (924124, 126, 127,
335, 336, 337, 516, 517)
ALWAYS engage differential lock (located in
left wheel hub) for best traction when throwing
snow.
4. Adjust Axle Lock (924125, 128, 338)
Use the axle lock pin to lock or unlock the right
wheel. Lock the right wheel to increase
traction; unlock the right wheel to allow for
easier turning of the unit.
5. Adjust Runners
Check and adjust Runners (see Service and
Adjustments). Allow 1/8 in. (3 mm) between
scraper blade and hard, smooth surface(s).
Allow 1-1/4 in. (30 mm) between scraper
blade and uneven or gravel surfaces.
6. Check Engine Fuel & Crankcase Oil
Check and add fuel if required. Check that the
engine crankcase oil is full using dipstick.
Refer to Engine Manual for detailed
instructions.
TO STOP IN AN EMERGENCY
Immediately release both control levers to stop
unit in an emergency. Stop engine, remove
key and wait for all rotating parts to stop before
leaving operator’s position.
STARTING AND SHUT OFF
IMPORTANT: Allow unit and engine to adjust
to the outdoor temperatures before clearing
snow. Before shut-off, run the attachment a
few minutes to prevent freeze-up.
NOTE: Try out each control without the engine
running to see how it works and what it does.
Manual Start
1. Turn discharge chute straight ahead.
2. Make sure that the traction clutch and
attachment drive clutch levers are fully
disengaged.
3. Push Primer Bulb 2 or 3 times for cold
engine.
WARNING: AVOID INJURY. Read
and understand the entire Safety
section before proceeding.
WARNING: AVOID INJURY. Read
and understand the entire Safety
section before proceeding.
WARNING: FAILURE TO FOLLOW
INSTRUCTIONS could result in
personal injury and/or damage to
unit. DO NOT attempt to start your
unit at this time. Read entire
Owner/Operator Manual and the
Engine Manual first.
GB - 18
NOTE: When temperature is below -15° F
(-26° C) additional priming may be needed.
4. If engine is cold, apply choke. See Engine
Manual for detailed instructions.
NOTE: A warm engine requires less choking
than a cold engine.
5. Set throttle to proper starting position.
6. Insert key into ignition switch.
12V - Turn key into RUN position.
120V or 240V - Push key into RUN
position. DO NOT twist key after it is
inserted.
7. Grasp starter handle and pull rope out
slowly until it pulls harder. Let rope rewind
slowly.
8. Pull rope with a rapid continuous full arm
stroke. Let rope rewind slowly.
IMPORTANT: DO NOT let Starter Handle
snap against Starter.
9. Repeat steps 7 and 8 until engine starts. (If
engine does not start, refer to
Troubleshooting.)
10. Adjust choke as needed.
11. Set throttle to Part Throttle or Slow
position for adaptation to outside
temperature or travel. Set throttle to Fast
position for normal operation.
Electric Start
1. Connect extension cord to prongs on
starter.
IMPORTANT: Prevent damage to unit. Know
voltage of your starter and only use matching
outlets.
2. Plug extension into 120V or 240V 3-wire,
grounded outlet.
3. Turn discharge chute straight ahead.
4. Make sure that the traction clutch and
attachment drive clutch levers are fully
disengaged.
5. Push Primer Bulb 2 or 3 times for cold
engine.
NOTE: When temperature is below -15° F
(-26° C) additional priming may be needed.
6. Insert key into ignition switch on engine
and push into "Run" position. DO NOT
twist key after it is inserted.
7. If engine is cold, apply choke. A warm
engine requires less choking than a cold
engine. See Engine Manual for detailed
instructions.
8. Set throttle to proper starting position.
9. Press starter button on engine until engine
starts.
IMPORTANT: DO NOT operate starter more
than 15 seconds per minute, as overheating
and damage can occur. (If engine does not
start, refer to Troubleshooting.)
10. Adjust choke as needed.
11. Disconnect power cord from outlet, then
starter.
12. Set throttle to Part Throttle or Slow
position for travel or adaptation to outside
temperature. Once achieved, set throttle
to Fast position for normal operation.
Electric Start (12V)
1. Turn discharge chute straight ahead.
2. Make sure that the traction clutch and
attachment drive clutch levers are fully
disengaged.
3. Push Primer Bulb 2 or 3 times for cold
engine.
NOTE: When temperature is below -15° F
(-26° C) additional priming may be needed.
4. If engine is cold, apply choke. See Engine
Manual for detailed instructions.
NOTE: A warm engine requires less choking
than a cold engine.
5. Set throttle to proper starting position.
6. Put ignition key into START position until
engine starts and release into the RUN
position.
IMPORTANT: DO NOT operate starter more
than 15 seconds per minute, as overheating
and damage can occur. (If engine does not
start, refer to Troubleshooting.)
7. Adjust choke as needed.
8. Set throttle to Part Throttle or Slow
position for travel or adaptation to outside
temperature. Once achieved, set throttle
to Fast position for normal operation.
Shut Off
1. Release Traction Drive Clutch Lever and
allow unit to come to a complete stop.
2. Run Impeller a few minutes after use to
prevent freeze-up of Impeller.
3. Release Attachment Clutch Lever and wait
for all moving parts to come to a complete
stop.
4. Move Throttle to the “Stop” position.
5. Remove key.
SNOW REMOVAL
IMPORTANT: Allow unit and engine to adjust
to the outdoor temperatures before clearing
snow.
NOTE: Attachment clutch should be engaged
before wheel drive clutch when throwing snow.
GB - 19
1. Select Speed Control position and
direction.
2. Engage Attachment Clutch - Right Hand
Lever.
3. Engage Traction Drive Clutch - Left Hand
Lever.
IMPORTANT: DO NOT overload unit capacity
by attempting to clear snow at too fast a rate.
Use slow speed to clear deep or hard packed
snow.
Tips for Operation
Snow is best removed as soon as possible
after snow fall.
To clear an area, run unit in an overlapping
series of paths. For large areas; start in the
middle and throw snow to each side, so snow
is not cleared more than once.
ALWAYS direct snow away from area to be
cleared and with direction of the wind.
TRAVELING
To travel from one work area to another:
1. Set Throttle to Slow or Part-Throttle
position.
2. Press down on handlebars enough to
raise front of unit slightly off surface.
3. Engage wheel drive clutch without
engaging attachment drive clutch.
TRANSPORT
ALWAYS shut off engine, remove key, and
close fuel shut-off valve when transporting unit
on a truck or trailer.
Use extra care when loading or unloading unit
onto trailer or truck.
Secure unit chassis to transport vehicle.
NEVER secure from rods or linkages that
could be damaged.
DO NOT transport machine while engine is
running.
Ariens Dealers will provide any service or
adjustments which may be required to keep
your unit operating at peak efficiency. Should
engine service be required, contact an Ariens
dealer or an authorized engine manufacturer's
service center.
SERVICE POSITION
Place unit on a flat level surface. Tip unit
forward onto front of impeller housing for
service. Assure unit is secure and will not tip
over. Strap and clamp onto bench if needed.
MAINTENANCE SCHEDULE
The chart below shows the recommended
maintenance schedule that should be
performed on a regular basis. More frequent
service may be required.
* After first two hours of operation.
MAINTENANCE
WARNING: AVOID INJURY. Read
and understand the entire Safety
section before proceeding.
WARNING: Before tipping unit up
onto housing, remove fuel so no
spills will occur and remove battery
(if equipped). Ensure unit is secure
and will not tip over during
maintenance.
MAINTENANCE
SCHEDULE
Service
Performed
Each
Use
Every
5 hrs.
Every
25
hrs.
Yearly
Check Dual
Handle
Interlock
Check
Fasteners
Check
Clutches
Clean Engine
Check Engine
Oil
Change
Engine Oil
*
Check Tire
Pressure
Check Auger
Gearcase
••
General
Lubrication
••
Battery
Maintenance
••
GB - 20
CHECK DUAL HANDLE
INTERLOCK
Without the engine running, press down
(engage) both clutch levers. Release
attachment clutch lever. Attachment clutch
should remain engaged until traction clutch
lever is released, then both clutches must
disengage.
CHECK FASTENERS
Make sure all hardware is tightened properly.
CHECK CLUTCHES
Auger / impeller must stop within 5 seconds
when attachment clutch/impeller brake lever is
released.
Wheels must stop quickly when traction drive
clutch lever is released.
If clutches do not engage or disengage
properly, adjust or repair before operation (see
Service and Adjustments).
CLEAN ENGINE
Refer to Engine Manual for detailed
instructions.
CHECK ENGINE OIL
The engine crankcase oil should be checked
every 5 hours of operation. Oil level MUST be
maintained in safe operating range on dipstick
at all times or engine damage will result (See
Engine Manual).
Park unit on a level surface. Refer to Engine
Manual for detailed instructions.
CHANGE ENGINE OIL
Change oil after first 2 hours of operation,
thereafter change oil every 25 hours (more
often if required). Refer to Engine Manual for
detailed instructions.
Run engine just prior to changing oil. Warm oil
will flow more freely and carry away more
contamination. Remove the oil drain plug from
the rear of the unit and tip the unit back to help
drain all the oil.
CHECK TIRE PRESSURE
Keep tires at pressure listed on the tire
sidewall.
CHECK AUGER GEARCASE
IMPORTANT: Proper oil level must be
maintained.
Gear cases are filled to the correct level at the
factory. Unless there is evidence of leakage,
no additional lubricant should be required.
Check oil level each season or every 25 hours
of operation.
To ensure adequate lubricant level:
1. Remove filler plug (Figure 14). Lubricant
must be at least up to bottom of lubricant
filler hole with unit resting on a
level-surface.
2. Add lubricant if required. Allow oil to drain
to level of plug and replace plug.
IMPORTANT: Use only Ariens special gear
lubricant L-2 (Part Number 00008000).
GENERAL LUBRICATION
IMPORTANT: Wipe each fitting clean before
and after lubrication.
IMPORTANT: DO NOT allow grease or oil to
get on friction disc, friction plate or belts.
NOTE: Apply Stens Mix Hi-Temp Grease or
equivalent to the lubrication fittings. See
Service Parts.
Sno-Thro should be lubricated (Figure 15) at
beginning of season or every 25 operating
hours.
Auger Shaft
NOTE: To grease auger shaft, remove shear
bolt nuts, and shear bolts. Turn auger on shaft
while applying grease at zerk fittings. Replace
shear bolt per instructions in Service and
Adjustments.
Figure 14
1.Auger Gearcase - Cast Iron
2.Oil Fill and Drain Plug
3.Auger Gearcase - Aluminum
3
2
1
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

Ariens 924126-ST11526DLE Manuale utente

Categoria
Spazzaneve
Tipo
Manuale utente

in altre lingue