Zenith HealthView H2050DT Installation And Operating Manual, Warranty

Marca: Zenith

Modello: HealthView H2050DT

Categoria: TV LCD

Tipo: Installation And Operating Manual, Warranty

machine number H2050DT

installation & operating guide / warranty

HealthView

Direct View

Television Receiver

WARNING

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.

REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence

of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a

risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating

and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

POWER CORD POLARIZATION:

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE

CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

NOTE TO CABLE/TV INSTALLER:

This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electric Code

(U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be

connected to the grounding system of the building, as close to the point of the cable entry as practical.

REGULATORY INFORMATION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in an institutional installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Do not attempt to modify this product in any way without written authorization from Zenith Electronics Corporation.

Unauthorized modification could void the user’s authority to operate this product.

HealthView is a trademark of Zenith Electronics Corporation.

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

PAGE 3

206-3491

1. Read Instructions

All the safety and operating instructions should be read

before the product is operated.

2. Follow Instructions

All operating and use instructions should be followed.

3. Retain Instructions

The safety and operating instructions should be retained for

future reference.

4.Heed Warnings

All warnings on the product and in the operating instruc-

tions should be adhered to.

5. Cleaning

Unplug this product from the wall outlet before cleaning.

Do not use liquid cleaners or aerosol cleaners. Use a damp

cloth for cleaning.

6. Water and Moisture

Do not use this product near water for example, near a

bath tub, wash bowl, kitchen sink, or laundry tub, in a wet

basement, or near a swimming pool.

7. Accessories

Do not place this product on an unstable cart, stand, tri-

pod, bracket, or table. The product may fall, causing serious

injury to a child or adult, and serious damage to the prod-

uct. Use only with a cart, stand, tripod, bracket, or table

recommended by the manufacturer, or sold with the prod-

uct. Any mounting of the product should follow the manu-

facturer’s instructions, and should use a mounting accesso-

ry recommended by the manufacturer.

8. Transporting Product

A product and cart combination should be moved with care.

Quick stops, excessive force, and uneven surfaces may

cause the product and cart combination to overturn.

9. Attachments

Do not use attachments not recommended by the product

manufacturer as they may cause hazards.

10. Ventilation

Slots and openings in the cabinet are provided for ventila-

tion and to ensure reliable operation of the product and to

protect it from overheating, and these openings must not

be blocked or covered. The openings should never be

blocked by placing the product on a bed, sofa, rug, or

other similar surface. This product should not be placed in

a built-in installation such as a bookcase or rack unless

proper ventilation is provided or the manufacturer’s instruc-

tions have been adhered to.

11. Power Sources

This product should be operated only from the type of

power source indicated on the marking label. If you are not

sure of the type of power supply to your home, consult

your product dealer or local power company. For products

intended to operate from battery power, or other sources,

refer to the operating instructions.

12. Line-Cord Polarization

This product is equipped with a three-wire grounding-type

alternating-current line plug. This plug will fit into the

power outlet only one way. This is a safety feature. If the

plug should still fail to fit, contact your electrician to

replace your obsolete outlet. Do not defeat the safety pur-

pose of the three-wire grounding-type plug.

13. Power-Cord Protection

Power-supply cords should be routed so that they are not

likely to be walked on or pinched by items placed upon or

against them, paying particular attention to cords at plugs,

convenience receptacles, and the point where they exit

from the product.

Important safeguards for you and your new product

Your product has been manufactured and tested with your safety in mind. However, improper use can result in potential

electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read

and observe the following safety points when installing and using your new product, and save them for future reference.

Observing the simple precautions discussed in this booklet can help you get many years of enjoyment and safe operation

that are built into your new product.

This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association.

(Continued on next page)

PORTABLE CART WARNING

IMPORTANT SAFETY INSTRUCTIONS

(Continued from previous page)

14. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the

product, be sure the antenna or cable system is grounded so

as to provide some protection against voltage surges and

built-up static charges. Article 810 of the National Electrical

Code (U.S.A.), ANSI/ NFPA 70 provides information with

regard to proper grounding of the mast and supporting

structure, grounding of the lead-in wire to an antenna dis-

charge unit, size of grounding conductors, location of

antenna-discharge unit, connection to grounding electrodes,

and requirements for the grounding electrode.

15. Lightning

For added protection for this product (receiver) during a

lightning storm, or when it is left unattended and unused

for long periods of time, unplug it from the wall outlet and

disconnect the antenna or cable system. This will prevent

damage to the product due to lightning and power-line

surges.

16. Power Lines

An outside antenna system should not be located in the

vicinity of overhead power lines or other electric light or

power circuits, or where it can fall into such power lines or

circuits. When installing an outside antenna system,

extreme care should be taken to keep from touching such

power lines or circuits as contact with them might be fatal.

17. Overloading

Do not overload wall outlets and extension cords as this can

result in a risk of fire or electric shock.

18. Object and Liquid Entry

Never push objects of any kind into this product through

openings as they may touch dangerous voltage points or

short-out parts that could result in a fire or electric shock.

Never spill liquid of any kind on the product.

19. Servicing

Do not attempt to service this product yourself as opening

or removing covers may expose you to dangerous voltage or

other hazards. Refer all servicing to qualified service person-

nel.

20. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing

to qualified service personnel under the following condi-

tions:

a. If the power-supply cord or plug is damaged.

b. If liquid has been spilled, or objects have fallen into the

product.

c. If the product has been exposed to rain or water.

d. If the product does not operate normally by following

the operating instructions. Adjust only those controls that

are covered by the operating instructions as an improper

adjustment of other controls may result in damage and will

often require extensive work by a qualified technician to

restore the product to its normal operation.

e. If the product has been dropped or the cabinet has been

damaged.

f. If the product exhibits a distinct change in performance.

21. Replacement Parts

When replacement parts are required, be sure the service

technician has used replacement parts specified by the man-

ufacturer or have the same characteristics as the original

part. Unauthorized substitutions may result in fire, electric

shock, or other hazards.

22. Safety Check

Upon completion of any service or repairs to this product,

ask the service technician to perform safety checks to deter-

mine that the product is in proper operating condition.

23. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as

recommended by the manufacturer.

24. Heat

The product should be situated away from heat sources such

as radiators, heat registers, stoves, or other products

(including amplifiers) that produce heat.

PAGE 4

Antenna Lead in Wire

Antenna Discharge Unit

(NEC Section 810-20)

Grounding Conductor

(NEC Section 810-21)

Ground Clamps

Power Service Grounding

Electrode System (NEC

Art 250, Part H)

Ground Clamp

Electric Service

Equipment

Example of Grounding According to National Electrical

Code Instructions

NEC - National Electrical Code

206-3491-O

IMPORTANT SAFETY INSTRUCTIONS

PAGE 5

Table of Contents

Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Important Safety Information . . . . . . . . . . . . . . . . . . .3

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Step 1. Hook Up TV

TV and other Equipment Hookups

Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Cable Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Antenna with VCR . . . . . . . . . . . . . . . . . . . . . . . . . .8

Cable service with VCR . . . . . . . . . . . . . . . . . . . . . . .9

Pillow Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Step 2. Channel Search and Reception Setup

Auto Program . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

(Select Antenna, or cable service and perform channel

search)

Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . .12

Installer’s Remote Key Functions . . . . . . . . . . . . . . . .13

On-Screen Menus Overview . . . . . . . . . . . . . . . . . . . 14

Step 3. Customize the HealthView TV’s

Features

Setup Menu (Start with page 12, Auto Program)

Add/Del/Blank . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Channel Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Timer Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Clock Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Captions Caption/Text . . . . . . . . . . . . . . . . . . . . . . .19

Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Video Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

FM Radio Menu . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Installer Parental Control Menu . . . . . . . . . . . . . . . .23

Other Menus and On-Screen Displays . . . . . . . . . . . .25

Managing the Channel Banks . . . . . . . . . . . . . . . . . .26

Installer Menus . . . . . . . . . . . . . . . . . . . . . . . . . . .29

LT1500 Quickset Clone Programmer . . . . . . . . . . . . . . .32

Patient Operation Section (Copy for patient usage)

Patient Remote Control Key Functions . . . . . . . . . . . . .35

Patient Parental Control Menu . . . . . . . . . . . . . . . . . .37

Patient Menus and On-Screen Displays . . . . . . . . . . . .39

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Warranty for HealthView Series TVs . . . . . . . . . . . . . . .43

Purchase the Optional Installer’s Remote and Clone Programmer

To preform the installation setup, you need an installer’s remote like the HP602, and the LT1500 Clone Programmer—

both are shown and described in later sections. The installer remote allows access to the Installer menus, User menus,

and Source/Channel Bank keys. The installer remote has Menu, Select, and Adjust Keys (Up/Down/Left/Right arrows) and

Source/Channel Bank Keys. The LT1500 Clone Programmer is used to duplicate a TV’s setup and install it on another TV.

See your Zenith Dealer.

Design and specifications subject to change without prior notice.

Installer/Hospital Note:

Pages 37, 38, 39, and 40 contain information and menus which the patient can use to operate the

TV. It is recommended that these four pages be copied and included with the literature packet that

the hotel provides to the patient.

206-3491-O

PAGE 6

206-3491-O

Mini glossary

75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider. Each end looks like a hex shaped nut with a wire

sticking through the middle, and it screws onto the threaded jack on the back of the TV.

A small device that connects a two-wire 300 ohm antenna to a 75 ohm RF jack. They are usually about an inch long with two screws

on one end and a round opening with a wire sticking out on the other end.

Hook Up The Antenna to the TV

Connect an off-air antenna to the HealthView TV.

If you have a 75 ohm RF cable, then you don’t need

any adapters!

A 300 to 75 ohm adapter is not included with the

Zenith HealthView TV.

300 TO 75 OHM

ADAPTER

ANTENNA

CABLE

M.P.I.

TV back

Flat wire

(300 ohm)

Antenna

300/75 ohm

Adapter

TV back panel

(expanded view)

PILLOW SPEAKER

SPKR

PILLOW

SPKR

TV back

TV back panel

(expanded view)

ANTENNA

CABLE

M.P.I.

RF coaxial wire

(75ohm)

Antenna

PILLOW SPEAKER

SPKR

PILLOW

SPKR

Locate the Antenna/Cable jack on the back of the

HealthView TV.

Connect the cable that runs from the wall directly to

this jack, according to the diagram to the right.

Remove the back of the remote and put in two AA bat-

teries.

Plug in the TV. Do not plug it into a switched outlet.

the HealthView TV is designed to operate on standard

current, 120-volt 60 Hertz AC. Do not attempt to oper-

ate it on DC Current.

Go to page 11 to Auto Program the HealthView TV.

back of

remote

PAGE 7

206-3491-O

Hook Up The Cable (CATV) to the TV

If you’re using a cable box, leave the TV on

channel 3 or 4 and use the cable box to change

channels.

If you’re using a cable box, Auto Program might

only find the channel the cable service is on

(usually channel 3 or 4).

Cable TV

wall jack

RF coaxial wire (75ohm)

TV back

ANTENNA

CABLE

M.P.I.

PILLOW SPEAKER

SPKR

PILLOW

SPKR

ANTENNA

CABLE

M.P.I.

Cable TV

wall jack

Cable box

Out

RF coaxial wire (75ohm)

3 4

output

switch

TV back

PILLOW SPEAKER

SPKR

PILLOW

SPKR

Locate the Antenna/Cable jack on the back of

the HealthView TV.

Connect the cable that runs from the wall

directly to this jack, according to the diagram

to the right.

Remove the back of the remote and put in two

AA batteries.

Plug in the TV. Do not plug it into a switched

outlet. Your HealthView TV is designed to

operate on household current, 120-volt 60

Hertz AC. Do not attempt to operate it on DC

Current.

Go to page 11 to Auto Program the

HealthView TV.

back of

remote

Connect cable service to the HealthView TV.

PAGE 8

206-3491-O

Hook Up Antenna and VCR to the TV

Connect the off-air antenna and VCR to the HealthView TV.

No A/V cables are included with the Zenith HealthView TV.

TV back

Out

Audio

Video

3 4

VCR back

VCR back AV panel

output

switch

ANTENNA

CABLE

M.P.I.

TV back panel

(expanded view)

TV back

PILLOW SPEAKER

SPKR

PILLOW

SPKR

Flat wire

(300 ohm)

Antenna

300/75 ohm

Adapter

TV back

RF coaxial wire

(75ohm)

not included

with TV

RF coaxial wire

(75ohm)

Antenna

Out

Audio

Video

3 4

VCR back

VCR back AV panel

output

switch

ANTENNA

CABLE

M.P.I.

TV back panel

(expanded view)

TV back

PILLOW SPEAKER

SPKR

PILLOW

SPKR

Locate the Antenna/Cable jack on the back of the VCR.

Connect the cable that runs from the antenna directly to

this jack, according to the diagram to the right.

Remove the back of the remote and put in two AA batter-

ies.

Plug in the TV. Do not plug it into a switched outlet. The

HealthView TV is designed to operate on standard cur-

rent, 120-volt 60 Hertz AC. Do not attempt to operate it

on DC Current.

Go to page 11 to Auto Program the HealthView TV.

back of

remote

PAGE 9

206-3491-O

Hook Up Cable Service (CATV) and VCR

Connect a VCR and Cable service to the HealthView TV.

Leave the VCR and the television tuned to channel

three or four and use the cable box to change

channels.

Cable TV

wall jack

Round wire (75ohm)

Cable box

Out

3 4

output

switch

Out

Audio

Video

3 4

VCR back

VCR back AV panel

output

switch

ANTENNA

CABLE

M.P.I.

TV back panel

(expanded view)

TV back

PILLOW SPEAKER

SPKR

PILLOW

SPKR

TV back

Cable TV

wall jack

Round wire (75ohm)

A/V cables

not included

with TV

Out

Audio

Video

3 4

VCR back

VCR back AV panel

output

switch

ANTENNA

CABLE

M.P.I.

TV back panel

(expanded view)

PILLOW SPEAKER

SPKR

PILLOW

SPKR

Locate the Antenna/Cable jack on the back of the

VCR.

Connect the cable that runs from the wall directly

to this jack, according to the diagram to the

right.

Remove the back of the remote and put in two

AA batteries.

Plug in the TV. Do not plug it into a switched

outlet. The HealthView TV is designed to oper-

ate on standard current, 120-volt 60 Hertz AC. Do

not attempt to operate it on DC Current.

Go to page 11 to Auto Program the HealthView

TV.

back of

remote

PAGE 10

206-3491-O

Pillow Speaker Hook Up

Locate the Pillow Speaker Output jack on the back of

the HealthView TV.

Connect an accessory pillow speaker or wired remote

control unit to this 6-pin jack.

Select PILLOW SPKR on the rear panel of the

HealthView TV.

Use a pillow speaker by Curbell, Model A-16455-02 or

other UL recognized pendant control bearing the warn-

ing: “Risk of fire if used in oxygen enriched atmos-

phere. Keep pendant control away from oxygen

equipment.”

M.P.I.

ANTENNA

CABLE

TV back

TV back panel

(expanded view)

PILLOW SPEAKER

SPKR

PILLOW

SPKR

Connect a pillow speaker to the HealthView TV.

SERIAL DATA ENCODER

(MALE PLUG)

VOLUME

CONTROL

SPKR.

COMMON

DATA

POWER

DATA

COMMON

POWER/DATA

SEPARATOR

ON/OFF

CHAN

DOWN

CHAN

(MALE

PLUG)

VOLUME CONTROL

SPKR.

TV ON/OFF

OPEN

CHAN UP/DATA IN

COMMON

AUDIO OUT

CHAN DOWN

Controlling the TV with serial data

Multiple control functions are handled with a single

wire at pin 3, where digitally encoded serial data is

entered. (Pin 4 is common for all functions.) Pin 3

sources up to 2mA during logic “0” for powering the

encoder in the pillow speaker. The encoder must sink

5 mA minimum from pin 4 (common) during the logic

“1” interval. Pillow speaker A-16455-02 by Curbell

meets this specification

Controlling the TV with mechanical switches

Pin 4 (common) is momentarily connected to pin 1,

3, or 6 via push-action switches to control On/Off and

Channel Up/Down. These pins are at +13 volts DC

(when measured from pin 4) with the switches open.

Current draw is 8 mA when a switch is closed. (This

operation is identical to previous Zenith models using

the 5-Wire Interface except that only +7 volts DC was

supplied and current draw was only 2.5 mA.)

Pillow Speaker Interface

This connector furnishes three control lines and an

audio output. A patient-pendant remote control, or

entertainment audio and nurse call system may be

connected here. All lines are isolated from the AC

power line and earth ground. (Opto-isolators isolate

the control lines, and a transformer isolates the

audio. There are no relays or inductive components in

the control lines.)

Pin no. Purpose

1 External TV On/Off switch

2 (not used)

3 External Channel Up switch or Data in

4 Common connection for control, data, and audio output.

Impedance to earth ground is a 10-meg resistor in parallel

with a 1100 pf capacitor.

5 Isolated audio output. Nominal 14-ohm source impedance

with short circuit protection. Intended for a pillow speaker

with a low-impedance pad-type volume control.

6 External Channel Down switch

Pillow speaker not included with

HealthView TV.

PAGE 11

206-3491-O

Auto Program (Channel Search)

Use Auto Program to specify Antenna or cable service

incoming signal source and automatically store all of the

channels that are found by channel search.

With the Installer remote control in hand, press the

POWER key to turn on the HealthView TV.

Press the MENU key so the Setup menu appears.

Using SELECT on the remote control, highlight Auto

Program on the screen.

Press a Right or Left ADJ (Adjust) arrow to reach the

Auto Program screen.

Using SELECT, choose either Cable TV or Off-Air Antenna

on the screen.

Press a Right or Left ADJ arrow to begin the Channel

Search.

Press ENTER when finished.

123

456

ENTER

POWER

TV/FM

FLSHBK

MUTE

VOLUME

CHANNEL

ADJ ADJ

SELECT

TIMER

BANK

CH PREVIEW

BED 1

BED 2

3/5

Mini glossary

OFF-AIR-ANTENNA If the patient can only view over-the-air broadcasts, select Antenna.

CABLE If you provide cable service to the patients, select Cable.

Note: Auto Program finds channels being received by the TV

tuner.

Cable will not work unless the hospital provides a cable service.

(If the Auto Program line appears in red, then it did not pass

one of the internal tests. To set Auto Program to white, set the

upper nibble of the EEPROM location $1FFh to $B0h.)

4/6

PAGE 12

206-3491-O

Front Panel Controls

power

channel

volume

captions

Press the POWER button to turn on the HealthView

TV.

Press the CHANNEL button, cycle through available

channels.

Press the VOLUME button to adjust the volume of the

HealthView TV.

Press CAPTIONS to select captions 1-4, text 1-4 or

captions off.

Using the front control panel to access the menus.

PAGE 13

206-3491-O

Installer Remote Key Functions

123

456

ENTER

POWER

TV/FM

FLSHBK

MUTE

VOLUME

CHANNEL

ADJ ADJ

SELECT

TIMER

BANK

CH PREVIEW

BED 1

BED 2

FLASHBK (FLASHBACK)

Return to the last channel viewed.

POWER

Turns TV On or Off

CHANNEL (UP/DOWN)

Flip through available channels.

MUTE

Turns sound Off and On, while the picture

remains.

ENTER

Press to view the Channel/Time display or

to remove any on-screen display or menu.

NUMBER KEY PAD

Selects channels directly and enters

numeric values for some options

remote control part number

HP602

124-213-04

TIMER

Press repeatedly to adjust TV turn-off time

up to 4-hours.

Use to pick AM/PM in Clock/Timer menu.

VOLUME LEFT/RIGHT

Adjusts the sound levels.

CC (CLOSED CAPTIONING)

Press to access closed captions.

Press ENTER to exit.

A quick list of the keys on the HP602 installer’s remote and what they do.

BANK

Press and repeat to select a Memory Bank

- - 1, 2, 3, or 4 (standby).

MENU/SELECT/ADJ (ADJUST)

Press MENU repeatedly to scroll through

either the Installer, or User menus. Use

SELECT to choose an option and ADJ

(adjust) to change the selected option.

CHANNEL PREVIEW

Gives installer access to the patient’s

menus. Displays the available TV channels

and hotel patient’s Parental Control menu.

Allows user to select the Aux Channel.

(Use the Audio/Video jacks on the back

of the TV as the source of the picture and

sound.)

TV/FM

Selects TV or Radio on TVs equipped with

FM radio.

BED 1/BED 2

Determines the code set transmitted, Bed

1 or Bed 2. Must correspond to setting of

BED ONE in the TV’s Installer Menu. Use a

paper clip or ballpoint pen to operate

this switch.

PAGE 14

206-3491-O

On-Screen Menus Overview

ON-SCREEN MENUS

Setup Menu Adjusts the basic characteristics of the TV

Auto Program 12 Automatically finds and stores active channels to scroll through using Channel Up/Down.

Add/Del/Blnk 15 Manually picks and chooses which active channels will appear when using Channel Up/Down

Channel Labels 16 Labels the channels with their network names (ABC, CBS, HBO, etc.).

Timer Setup 17 Programs a time for the TV to turn itself on or off, or to turn itself off after a certain amount

of time.

Clock Set 18 Sets the time.

Caption/Text 19 Chooses the captioning or text option.

Language 20 Picks the language the on-screen menus will appear in.

Video Menu 21 Adjusts the picture for any viewing situation. The options are: Contrast, Brightness, Color,

Tint, Sharpness, Picture Pref.

FM Radio Menu

22 Adjusts the FM Radio options.

Parental Control 23 Allows installer to block any channel or A/V source for up to 99 hours, with the use of a pass

word.

25 OTHER MENUS AND ON-SCREEN DISPLAYS

Channel/Time Shows the current time, channel, video and type of incoming audio signal.

Alarm Sets the wake-up time.

Sleep Timer Sets the time the TV will turn off.

Volume Shows current sound level.

Captions Sets Caption/Text options.

Ch Preview Displays the available channels list.

Channel Bank Shows currently selected channel bank.

INSTALLER MENUS 29

Descriptions of all the menus on the TV.

Using the Menu button on the installer’s remote, the installer can access all the menus below.

Menu Name Page Description

PAGE 15

206-3491-O

Fine-tune the patient’s channel selection list.

Setting Add/Delete/Blank

Press the MENU key on the Installer’s remote so the Setup

menu appears.

Press SELECT repeatedly to highlight the Add/Del/Blnk

option.

Using either the NUMBER keypad and ENTER or the

Channel Up/Down arrows on the remote, select a chan-

nel.

(If adding a deleted channel, you will need to use the

number pad and ENTER.)

Using the Right/Left ADJ arrows, pick whether that

channel is Added, Deleted, or Blank.

To continue, select another channel and repeat Step 3.

When you are finished, press ENTER to remove menu.

Adding Aux, VCR 3, VCR 4, or FM to the

Channel Preview List

Go to the Setup menu, select the Add/Del/Blnk option.

Use Channel Up/Down to select the option and choose

Added.

Note: If the option was turned off in the Service menu,

you will have to reinstate it before it can appear as an

option in the Channel Preview list.

Notes: Adding VCR 3 and/or VCR 4 as available channels

forces TV Channel 3 and/or 4 to be retained, when run-

ning Auto Program, even though the equipment connect-

ed to the Antenna/Cable (RF) jack (like a cable convert-

er and/or VCR) may be turned off.

You can elect to Add, Delete or Blank: VCR 3, VCR 4,

and Aux. FM can be Added or Deleted, but not Blanked.

123

456

ENTER

POWER

TV/FM

FLSHBK

MUTE

VOLUME

CHANNEL

ADJ ADJ

SELECT

TIMER

BANK

CH PREVIEW

BED 1

BED 2

CH 44 ADDED

Mini glossary

ADD Adds new channels to the list that the patient can scroll through when using the remote.

DELETE Removes channels for one reason or another from the list that the patient can scroll through.

BLANK Removes the video signal from a channel so the patient will only receive the audio signal.

3/5

If you delete a channel, it isn’t gone for good. Just select it

using the NUMBER keypad on the remote, or add it later.

PAGE 16

206-3491-O

Setting Up Channel Labels

123

456

ENTER

POWER

TV/FM

FLSHBK

MUTE

VOLUME

CHANNEL

ADJ ADJ

SELECT

TIMER

BANK

CH PREVIEW

BED 1

BED 2

A & E

Overview

Channel Labels help the user identify the channel or network being viewed.

In the Setup menu with the CH LABELS option highlighted, use the Adjust

Left/Right arrows to scroll through the available channel labels, such as, A &

E, AMC, ESPN, HBO, etc. These are a series of alphabetically organized preset

labels from which you can choose the more common networks. Use any of

these or create custom labels.

- - - - , The 4 dashes will allow a channel label to appear; if one is provided

by XDS. (Extended data service)

NONE, prevents any channel label from appearing.

LAB 1, thru LAB 20, are the 20 programmable labels.

The 20 programmable labels can be customized for your needs.

Each programmable label has 5 characters spaces available.

To Program a Channel Label

First select a channel using the NUMBER keypad and ENTER or the Channel

Up/Down arrows, on the Installer’s remote control.

(To select a deleted channel, use the NUMBER keypad and ENTER.)

To program a channel label, go to the Setup menu and select CH LABELS.

Press the Right/Left adjust arrow to scroll the available preset labels. Scroll

past - - - -, scroll past NONE, to go to the first programmable label slot, LAB

1. Notice that the label appears with the title LAB 1, and is also on a dark

background; which will distinguish it from the preset labels.

Operating the Menu

Use Volume Up/Down to select the first letter.

Press MUTE to clear the label if necessary.

Use Channel Up/Down to change the character to one of the 255 characters

available.

Adjust Left/Right Switches to the next label.

- - moves to the next or previous

label.

Volume Up/Down Selects character spaces

- - moves to the next or previous

character space.

Channel Up/Down Scrolls through the available

characters.

ENTER Accept the channel label and

removes the menu.

MUTE Removes current label,

- - if first character space is selected.

PAGE 17

206-3491-O

Timer Set Up

The Sleep Timer may be instantly set by pressing the TIMER key

repeatedly. When you have made the selection, press ENTER to set

the Sleep Timer and return to TV viewing.

The On/Off Timer will not work until the Clock on the television

has been set.

Set times to turn the HealthView TV on or off automatically.

Be sure to set the Clock first, see next page.

With Timer Setup highlighted as shown above, press a

Left/Right ADJ arrow to display the Timer setup menu.

Use the SELECT key to pick On Time.

Use the Number keypad to enter the hours, then minutes

of the time you want the TV to turn on.

Use the TIMER key to specify AM or PM.

Use the SELECT key to pick Off Time.

Use the Number keypad to enter the hours, then minutes

of the time you want the TV to turn off.

Use the TIMER key to specify AM or PM.

Press ENTER to set the timer and return to TV viewing.

123

456

ENTER

POWER

TV/FM

FLSHBK

MUTE

VOLUME

CHANNEL

ADJ ADJ

SELECT

TIMER

BANK

CH PREVIEW

BED 1

BED 2

2/5

TO SET TIMERS

Mini glossary

ON TIME The time the TV will automatically turn itself on each day.

OFF TIME The time the TV will automatically turn itself off each day.

ON/OFF TIMER Activates or deactivates the on/off timer feature.

3/6

4/7

PAGE 18

206-3491-O

The Sleep Timer may be instantly set by pressing the TIMER key

repeatedly. When you have made the selection, press ENTER to

set the timer and return to TV viewing.

Clock Set

Set the clock on the HealthView TV.

123

456

ENTER

POWER

TV/FM

FLSHBK

MUTE

VOLUME

CHANNEL

ADJ ADJ

SELECT

TIMER

BANK

CH PREVIEW

BED 1

BED 2

11:44 PM

Highlight the Clock Set option.

Set the current time; use the Number keypad to enter the

hours, then minutes. For example, enter 06, then 30, to set

6:30 on the clock.

Use the TIMER key to specify AM or PM.

Press ENTER to start the clock and return to TV viewing.

Mini glossary

TIME A four-digit figure broken down into hours and minutes.

HOURS First two digits that are entered when setting the clock, or the on/off timer.

MINUTES The last two digits that are entered when setting the clock, or the on/off timer.

PAGE 19

206-3491-O

Turns on closed-captioning or text that appears at

the bottom of the screen.

Using SELECT on the remote control, select Captions/Text on

the screen.

Use the Right/Left ADJ arrows to choose any of the follow-

ing options: Caption 1, Caption 2, CAption 3, Caption 4,

Text 1, Text 2, Text 3, or Text 4.

Press ENTER to remove menu.

Captions come in handy when the television is on mute.

Standard closed captioning is available using the Caption 1 option.

Not all programming has closed captioning or text available.

Caption/Text

CAPTION 1

123

456

ENTER

POWER

TV/FM

FLSHBK

MUTE

VOLUME

CHANNEL

ADJ ADJ

SELECT

TIMER

BANK

CH PREVIEW

BED 1

BED 2

2/3

Mini glossary

CAPTIONS The term for the words that scroll across the bottom of the TV screen; usually the audio portion of the program provided for the hearing

impaired.

TEXT The term for the words that appear in a large black frame and almost cover the entire screen; usually messages provided by the broadcaster.

Caption/Text is a feature which allows the HealthView TV to receive the

closed caption and/or text options if made available by the broadcaster.

Availability and functionality of Caption/Text features is determined only

by each broadcaster and may not be available in your area.

PAGE 20

206-3491-O

Language

ENGLISH

123

456

ENTER

POWER

TV/FM

FLSHBK

MUTE

VOLUME

CHANNEL

ADJ ADJ

SELECT

TIMER

BANK

CH PREVIEW

BED 1

BED 2

Choose the language for the on-screen menus.

Press the MENU key on the remote control so the Setup

menu appears.

Use the SELECT key on the remote control, to highlight

Language on the screen.

Press a Right/Left ADJ arrow to choose one of the fol-

lowing options: English, Spanish or French.

Press ENTER to return to TV viewing.

La pagina sta caricando ...

Zenith HealthView H2050DT Installation And Operating Manual, Warranty

Marca: Zenith

Modello: HealthView H2050DT

Categoria: TV LCD

Tipo: Installation And Operating Manual, Warranty

Scarica il pdf

rapporto

in altre lingue

English: Zenith HealthView H2050DT

Zenith HealthView H2050DT Installation And Operating Manual, Warranty

Zenith HealthView H2050DT Installation And Operating Manual, Warranty

in altre lingue

Documenti correlati

Altri documenti