Yamaha TSX-B235 Black Manuale utente

G

Printed in Malaysia ZR50350

DESKTOP AUDIO SYSTEM

SYSTEME AUDIO DESKTOP

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

English Français Deutsch Svenska Italiano Español Nederlands Русский

i En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this unit in a well ventilated, cool, dry, clean place -

away from direct sunlight, heat sources, vibration, dust,

moisture and cold. For proper ventilation, allow the

following minimum clearances.

Top: 15 cm (6 in)

Rear: 10 cm (4 in)

Sides: 10 cm (4 in)

3 Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes

from cold to hot, and do not locate this unit in an

environment with high humidity (i.e. a room with a

humidifier) to prevent condensation inside this unit, which

may cause an electrical shock, fire, damage to this unit,

and/or personal injury.

5 Avoid installing this unit where foreign object may fall

onto this unit and/or this unit may be exposed to liquid

dripping or splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to

this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If the

temperature inside this unit rises, it may cause fire,

damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using

this unit with a higher voltage than specified is dangerous

and may cause fire, damage to this unit, and/or personal

injury. Yamaha will not be held responsible for any

damage resulting from use of this unit with a voltage other

than specified.

13 To prevent damage by lightning, keep the power cable

disconnected from a wall outlet or this unit during a

lightning storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed.

The cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the

wall outlet.

16 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit

is faulty.

17 Before moving this unit, press to set the unit to off,

and disconnect the AC power plug from the wall outlet.

18 Condensation will form when the surrounding

temperature changes suddenly. Disconnect the power

cable from the outlet, then leave this unit alone.

19 When using this unit for a long time, this unit may become

warm. Turn off, then leave this unit alone for cooling.

20 Install this unit near the wall outlet and where the AC

power plug can be reached easily.

21 The batteries shall not be exposed to excessive heat such

as sunshine, fire or the like. When you dispose of

batteries, follow your regional regulations.

– Keep the batteries in a location out of reach of children.

Batteries can be dangerous if a child were to put in his or

her mouth.

– If the batteries grow old, the effective operation range of

the remote control decreases considerably. If this happens,

replace the batteries with new one as soon as possible.

– Do not use old batteries together with new ones.

– Do not use different types of batteries (such as alkaline

and manganese batteries) together. Read the packaging

carefully as these different types of batteries may have the

same shape and color.

– Exhausted batteries may leak. If the batteries have leaked,

dispose of them immediately. Avoid touching the leaked

material or letting it come into contact with clothing, etc.

Clean the battery compartment thoroughly before

installing new batteries.

– If you plan not to use the unit for a long period of time,

remove the batteries from the unit. Otherwise, the batteries

will wear out, possibly resulting in a leakage of battery

liquid that may damage the unit.

– Do not throw away batteries with general house waste.

Dispose of them correctly in accordance with your local

regulations.

22 Excessive sound pressure from earphones and headphones

can cause hearing loss.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

This unit is not disconnected from the AC power source as

long as it is connected to the wall outlet, even if this unit

itself is turned off by . In this state, this unit is designed

to consume a very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR

MOISTURE.

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

There is a chance that placing this unit too close to a CRT-

based (Braun tube) TV set might impair picture color.

Should this happen, move this unit away from the TV set.

1 En

English

NAMES OF PARTS AND THEIR FUNCTIONS ........2

Top panel / Front panel..................................................2

Front panel display.........................................................3

Rear panel......................................................................3

Remote control...............................................................4

TURNING THE UNIT ON...........................................5

ADJUSTING THE CLOCK ........................................5

ADJUSTING THE TONE (remote control only)......6

ADJUSTING THE BRIGHTNESS OF THE FRONT

PANEL DISPLAY (remote control only) .................6

CHARGING WITH THE CHARGING PORT .............6

LISTENING TO CD AND USB DEVICES .................7

Listening to a CD............................................................7

Listening to a USB device..............................................8

Using repeat/shuffle playback (remote control only)......9

LISTENING TO EXTERNAL SOURCES...................9

LISTENING TO MUSIC FROM YOUR Bluetooth

COMPONENT..........................................................10

Playing back from your Bluetooth component..............10

Connecting an already-paired component via

Bluetooth

... 11

Disconnecting a Bluetooth connection.........................12

LISTENING TO DAB STATIONS (TSX-B235D only) ...12

Preparing for DAB reception ........................................12

Selecting DAB stations.................................................13

Presetting DAB stations (remote control only) .............14

Selecting preset DAB stations......................................14

LISTENING TO FM STATIONS ..............................15

Selecting an FM station................................................15

Presetting FM stations (remote control only) ...............16

Selecting preset FM stations........................................17

USING THE ALARM FUNCTION (IntelliAlarm).....18

Setting the alarm..........................................................19

Operations while the alarm sound is playing................20

USING THE “DTA CONTROLLER” .......................21

USING THE SLEEP TIMER ....................................21

SETTING AUTO POWER STANDBY FUNCTION

(main unit only) ......................................................21

TROUBLESHOOTING ............................................22

NOTES ON DISCS AND USB DEVICES................25

SPECIFICATIONS...................................................26

CONTENTS

• Play back music from external devices such as your audio/data CDs, USB devices, or external devices via the AUX jack,

and listen to the radio.

• (TSX-B235D only) Listen to the DAB radio.

•By the Bluetooth technology, you can enjoy clear sound without wire connections. One touch pairing enabled by NFC

technology.

• Use your favorite music or a beep tone as an alarm. When the set time arrives, the music you select is played at the

volume that you specify, giving you the ideal start to your day (IntelliAlarm function).

• By using the free “DTA CONTROLLER” application for a smartphone and tablet computer, you can control this unit and

take advantage of more sophisticated alarm functionality (+ P. 21).

• You can easily store and recall of your favorite radio stations, up to 30 FM and 30 DAB stations (DAB function is only

for TSX-B235D).

• Bass, middle, and treble can be adjusted to your taste.

 About this manual

• References to the iPod appearing in this manual also include the iPhone and iPad.

• If an operation can be performed using either the buttons on the unit itself or from the remote control, the explanation will

focus on operation using the main uint.

• indicates precautions for use of the unit and its feature limitations.

• indicates supplementary explanations for better use.

 How to use the remote control  Installing batteries in the remote control

Features

Supplied accessories

Batteries (x 2)

(AAA, R03, UM-4)

FM antenna

(for TSX-B235)

Remote control DAB/FM antenna

(for TSX-B235D)

USB cap (x 2)

Keep the USB cap out

of reach of children so

as to ensure that it is

not mistakenly

swallowed.

Within 6 m (20')

Check the “+” and “-” of the

batteries and insert them the

correct way around.

(at the end of this manual)

Additional information............................................i

2 En

1 VOLUME – / +

Adjust the volume.

2 (Power)

Press to turn the unit on/off (standby).

There are two types of the standby state (+ P. 5).

3 Source buttons

Switch the audio source to be played.

If you press one of these while the unit is in standby

(except ECO standby), the unit will turn on and then

switch the audio source.

(TSX-B235D only) When listening to the radio, press

RADIO to switch between DAB/FM.

4 NFC mark

Allows easy pairing with NFC technology (+ P. 11).

5 Audio control buttons

Use these to operate the CD/USB device.

6 SNOOZE/SLEEP

Set the sleep timer or switch the alarm to snooze mode

(+ P. 20, 21).

7 CHARGING port

This port is for use to charge only.

Supplies 5V/1.0A to a portable device, such as a

smartphone, when it is connected with a USB cable

(+ P. 6).

When the USB device is not in use, put the USB cap in place to

protect the connector.

8 USB port

Connect and play your USB device here (+ P. 8).

When the USB device is not in use, put the USB cap in place to

protect the connector.

9 PRESET /

Select a radio station that you stored (+ P. 16, 17).

0 TUNING /

Tune the radio (+ P. 15, 16).

A (Headphone jack)

Connect headphones here.

B ALARM

Switch the alarm on/off (+ P. 20).

C SET

Set the alarm (+ P. 19).

D –/+

Select an item or value when setting the clock or the

alarm.

E EJECT

Eject the CD.

F Disc slot

Insert a CD here (+ P. 7).

G ENTER

Confirm a selected item or value.

H Front panel display

The clock and other information is displayed here

(+ P. 3).

NAMES OF PARTS AND THEIR FUNCTIONS

Top panel / Front panel

A

3

7 9 054612

CB GD FE H

8

: Stop

: Play/Pause

/ :

Skip, Search backward/forward (press and hold

down)

3 En

NAMES OF PARTS AND THEIR FUNCTIONS

English

1 Illumination sensor

Detect ambient lighting. Do not cover this sensor

(+ P. 6).

2 Alarm time

Indicates the alarm time (+ P. 19).

3 Repeat/shuffle indicator

Displays the playback mode (+ P. 9).

4 Secondary indicator (TSX-B235D only)

Turns on if a secondary station is playing when you

listen to a DAB station.

5 Multi-function indicator

Displays various information, including the clock time,

information about the currently-playing track, and the

frequency of the radio station.

6 Remote control signal receiver

Make sure that this sensor is not obstructed (+ P. 1).

7 Weekly alarm indicator

Shows alarm information specified using the free “DTA

CONTROLLER” application for a smartphone and

tablet computer (+ P. 21).

8 Alarm indicator

Turns on if the alarm has been set (+ P. 20).

9 Sleep indicator

Turns on if the sleep timer has been set (+ P. 21).

1 CLOCK switch

Sets the clock and specifies whether the clock will be

displayed (+ P. 5).

2 AUX

Use a commercially available 3.5 mm mini-plug cable

to connect your external device here (+ P. 9).

3 DAB/FM antenna connector

Connect the DAB/FM antenna here.

• If reception is poor, try changing the height or direction of the

antenna, or move the unit to find a location that has better

reception.

• If you use a commercially available outdoor antenna instead of

the supplied antenna, reception may be better.

Front panel display

~~~~~~

65

7

21

8 9

3 4

Rear panel

FM ANT

ON

CLOCK AUX

SET OFF

1 2 3

(TSX-B235)

SET:

Set the clock.

ON:

Even when the unit is off, the clock will be

displayed and the alarm function will be available.

OFF:

When the unit is off, the clock will not be displayed

and the alarm function will not be available

.

FM ANT

Be sure to stretch out the antenna.

NAMES OF PARTS AND THEIR FUNCTIONS

4 En

1 Remote control signal transmitter

2 (Power)

Press to turn the unit on/off (standby).

There are two types of the standby state (+ P. 5).

3 SNOOZE/SLEEP

Set the sleep timer or switch the alarm to snooze mode

(+ P. 20, 21).

4 ALARM

Switch the alarm on/off (+ P. 20).

5 Source buttons

Switch the audio source to be played. If you press one of

these while the unit is in standby (except ECO standby),

the unit will automatically turn on and then switch the

audio source..

(TSX-B235D only) When listening to the radio, press

RADIO to switch between DAB/FM.

6 Item selection buttons

FOLDER S/T: Select items or switch the playback

folder when playing music on data

CDs or USB devices.

ENTER: Confirm a selected item.

7 Audio control buttons

Use these to operate the CD/USB device.

8 (Repeat)/ (Shuffle)

Play music on a CD or USB device in repeat/shuffle

mode (+ P. 9).

9 EQ: LOW/MID/HIGH

Adjust the bass, middle or treble sound quality

(+ P. 6).

0 TUNING /

Tune the radio (+ P. 15, 16).

A PRESET /

Select a radio station that you stored (+ P. 16, 17).

B MEMORY

Store a radio station (+ P. 16).

C DIMMER

Adjusts the brightness of the front panel display

(+ P. 6).

D DISPLAY

Switch the information shown in the front panel display

(+ P. 7, 8, 15).

E VOLUME +/–

Adjust the volume.

F MUTE

Mute or unmute the sound.

Remote control

3

4

5

7

8

:

A

B

1

6

2

9

D

C

F

E

: Stop

: Play/Pause

/ :

Skip, Search backward/forward (press and hold

down)

5 En

English

TURNING THE UNIT ON

Connect the power cable to an AC outlet, and

press .

The unit will turn on, and will be ready to play audio

sources.

Press once again to turn the unit off (standby).

There are two types of the standby as below. The state

can be set in the rear panel CLOCK switch (+ P. 3).

Mode Clock switch Clock display

Bluetooth

connection

Charging USB

devices

(USB port and

CHARGING port)

Alarm setting

Standby ON Show Enable Enable Enable

ECO standby

(power saving

mode)

OFF No clock display Disable Enable Disable

ADJUSTING THE CLOCK

1 Set the rear panel CLOCK switch to the SET

position.

The display will indicate “CLOCK YEAR,” and the

numerical value to be set will blink.

2 Set the date and time.

Press the front panel – / + buttons to edit the values,

and then press ENTER to confirm the setting.

Set the items in the order of year month day

hour minute.

When clock setting has finished, the display will

indicate “Completed!”

On step , by pressing SNOOZE/SLEEP you can select

the time format (12-hour / 24-hour).

3 Set the CLOCK switch to the ON position.

The moment you set the switch to the ON position, the

clock will start from 0 second.

The time settings will be reset if the unit remains unpowered for

more than one week.

26

Apr

15:30

CD

Display (24-hour) when the unit is on

Display (24-hour) when the unit is off (standby*)

* In ECO standby, the clock display will disappear.

ON

CLOCK AUX

SET OFF

26

Apr

Front panel

1

2

ON

CLOCK AUX

SET OFF

3

Rear panel

(24-hour)

Jan Feb Mar Apr May Jun

January February March April May June

Jul Aug Sep Oct Nov Dec

July August September October November December

2

6 En

ADJUSTING THE TONE (remote control only)

1 During playback, press the LOW, MID, or

HIGH EQ button on the remote control.

Select the tone to be adjusted (LOW, MID, HIGH).

2 Press S/T to adjust the tone.

3 Press ENTER on the remote control to

complete the operation.

You can also press the EQ button that you pressed in

Step to complete the settings.

If you want to adjust another frequency band, return to

step and press the EQ button for the frequency

band that you want to adjust.

ADJUSTING THE BRIGHTNESS OF THE FRONT PANEL

DISPLAY (remote control only)

Press DIMMER repeatedly on the remote

control.

The brightness of the front panel display will change in

the order shown below.

AUTO 1 (bright) 2 (medium) 3 (dim)

back to AUTO

When AUTO is set, the brightness of the front panel display is

adjusted automatically with the Illumination sensor (+ P. 3 ).

Ensure that the sensor is not covered.

CHARGING WITH THE CHARGING PORT

Connecting a USB device such as a smartphone or tablet

computer to the CHARGING port on this unit charges the

connected device (power supply of up to 5V/1.0A is

supported). Charging is possible even when the unit is

off.

Prepare a USB cable that is compatible with the USB

device.

• Charging may not be possible depending on the USB device.

• Yamaha will not be held responsible for any damage to the

USB device or data loss occurred while using this unit.

1

2

3

1

7 En

English

 Skipping folders (remote control only)

 Display information (remote control only)

LISTENING TO CD AND USB DEVICES

The unit will operate as follows when playing back tracks/files on CD/USB devices.

• If the CD/USB device being played is stopped, the track that you listened will start playback from the beginning of the

track the next time you play.

• If you press while playback is stopped, tracks will play as follows the next time playback begins:

− Audio CD: Play from the first track of the CD.

−

Data CD*/USB device:

Play from the first track of the folder contains the track you listened to last time.

• This unit automatically turns off if no operation has been performed for 20 minutes after CD/USB device playback is

stopped.

* “Data CD” is a CD that contains MP3/WMA files.

For details on playable discs and files, refer to “NOTES ON DISCS AND USB DEVICES” (+ P. 25).

Listening to a CD

1 Press the CD source button to switch the

audio source to CD.

If a CD is already inserted, playback will start.

2 Insert a CD into the disc slot.

Playback starts automatically.

Playback can be controlled with either the remote

control, or the front panel on this unit (+ P. 2, 4).

Insert the CD with the label side facing upward.

Folders and files on a data CD are played in alphabetical order.

While a data CD is playing, you can use the remote control’s

FOLDER ▲/▼ buttons to select the folder.

The folder number (only for a data CD) or the song/file

number is shown for several seconds when starting playback

or skipping tracks.

If you press

DISPLAY

on the remote control while a song is

playing or paused, the information shown on the front panel

display will be switched in the following order.

- Elapsed song playback time

- Remaining song playback time (only for an audio CD)

- Song name*

- Album name*

- Artist name*

- File name (only for a data CD)

- Folder name (only for a data CD)

* Shown only if this data is included in the song.

AUX

USB

CD

RADIO

1

2

LISTENING TO CD AND USB DEVICES

8 En

For details on the supported USB device, refer to “NOTES ON DISCS AND USB DEVICES” (+ P. 25).

 Skipping folders (remote control only)

 Display information (remote control only)

Listening to a USB device

1 Press the USB source button to switch the

audio source to USB.

If a USB device is already connected, playback will start.

2 Connect a USB device to the USB port.

Playback starts automatically.

Playback can be controlled using either the remote control

or the front panel on this unit (

+

P. 2, 4).

• Folders and files will play in the order in which they were written.

• A USB device is automatically charged when it is connected to

the USB port (5 V/1.0 A output).

• Stop playback before disconnecting the USB device.

• The iPod cannot be played back.

• Charging may not be possible depending on the USB device.

While a USB device is playing, you can use the remote

control’s FOLDER ▲/▼ buttons to select the folder.

The folder/file number is shown for several seconds when

starting playback or skipping tracks.

If you press

DISPLAY

on the remote control while a song is

playing or paused, the information shown on the front panel

display will be switched in the following order

.

- Elapsed song playback time

- Song name*

-Album name*

- Artist name*

-File name

- Folder name

* Shown only if this data is included in the song.

AUX

USB

CD

RADIO

1 2

9 En

LISTENING TO CD AND USB DEVICES

English

The playback status is shown by the repeat/shuffle indicator in the front panel display (+ P. 3).

Repeat playback Shuffle playback

Using repeat/shuffle playback (remote control only)

Press (repeat) repeatedly to

select one of the following

playback modes.

No display: Repeat mode off

: 1 track

: All tracks within the folder (data CD/USB device

only)

: All tracks

Press (shuffle) repeatedly to

select one of the following

playback modes.

No display: Shuffle mode off

: All tracks within the folder (data CD/USB device

only)

: All tracks

LISTENING TO EXTERNAL SOURCES

1 Using a commercially available 3.5 mm mini-

plug cable, connect your external device to the

AUX jack on the rear panel of this unit.

• Turn the unit off before connecting the audio cable.

• Turn down the volume of the unit and your external audio

device before connection.

2 Press to turn the unit on.

3 Press the AUX source button to switch the

audio source to AUX.

4 Start playback on the connected external

audio device.

ON

CLOCK AUX

SET OFF

AUX

USB

CD

RADIO

1

2

Rear panel

3

10 En

This unit provides Bluetooth functionality. You can enjoy wireless music playback from your Bluetooth component (mobile

phone, digital audio player, etc.). Please also refer to the owner’s manual of your Bluetooth component.

You’ll need to perform the pairing operation the first time you use your Bluetooth component with this unit, or if the pairing

settings have been deleted. Pairing is an operation that registers the communicating component (subsequently called “the

other component”) with this unit. Once pairing has been completed, subsequent reconnection will be easy even after the

Bluetooth connection is disconnected (+ P. 11). If pairing is not successful, refer to the item “Bluetooth” in

“TROUBLESHOOTING” (+ P. 23).

Yamaha does not guarantee all connections between this unit and Bluetooth component.

• This unit can be paired with up to 8 other components. When pairing with the ninth component has succeeded, pairing data for the

component with the oldest connection date will be deleted.

• If this unit is connected via Bluetooth to another component, hold down source button on this unit or on the remote control

to disconnect the Bluetooth connection before you perform the pairing operation.

LISTENING TO MUSIC FROM YOUR

Bluetooth

COMPONENT

Playing back from your Bluetooth component

1 Press the source button to switch the

audio source to Bluetooth.

2 Perform Bluetooth pairing on the other

component.

For details refer to the owner’s manual of the other

component.

3 From the Bluetooth connection list of the other

component, choose this unit (TSX-B235

Yamaha or TSX-B235D Yamaha).

When pairing has been completed, the front panel display

of this unit will indicate “BT Pairing OK”.

If you are asked to enter a password, enter the numerals “0000”.

4 Connect this unit and your other component

via Bluetooth.

5 Play back music from your Bluetooth

component.

Take care that the volume setting of this unit is not too high. We

recommend that you adjust the volume on the other component.

• If you connect via Bluetooth from your other component and

playback music while this unit is in standby (except ECO

standby), this unit will automatically turn on.

• If you disconnect the Bl uetooth connection from your other

component while the audio source is set to Bluetooth, this unit

will automatically turn off.

•If Bluetooth is selected as the audio source, this unit will

automatically turn off when 20 minutes have elapsed without any

Bluetooth connection nor any operation performed.

AUX

USB

CD

RADIO

1

15:30



BT

Pairing OK

3

11 En

LISTENING TO MUSIC FROM YOUR Bluetooth COMPONENT

English

 Easy pairing

For the smartphone with NFC (Near Field Communication) function, you can easily perform the pairing operation just by

holding the smartphone over the NFC mark (you need to turn the unit on and turn on the NFC function of the smartphone

beforehand).

Once pairing has been completed, connecting a Bluetooth will be easy the next time.

 Connecting from this unit

 Connecting from the other component

1 Hold the smartphone over the NFC mark.

2 Perform the pairing operation at the

smartphone (for details, please read the

owner’s manual of the smartphone).

This unit is indicated as “TSX-B235 Yamaha” or “TSX-

B235D Yamaha” on the smartphone.

• If you are prompted for a passkey, enter the numerals “0000”.

• If the connection fails, move the smartphone slowly on the

NFC mark.

• If the smartphone is equipped with a case, remove the case.

Connecting an already-paired component via Bluetooth

Press the source button to switch the

audio source to Bluetooth.

The Bluetooth indicator will blink in the front panel display;

this unit will search for the other component that was most

recently connected via Bluetooth, and will then establish a

connection (You must first turn on the Bluetooth setting of

the other component).

When the Bluetooth connection has been established, the

Bluetooth indicator will light, and the name of the other

component will be displayed.

1 In the Bluetooth settings of the other component, turn Bluetooth on.

2

From the

Bluetooth

connection list of the other component, choose this unit (TSX-B235 Yamaha or

TSX-B235D Yamaha).

The Bluetooth connection will be established, and the front panel display of this unit will indicate the name of the other

component.

• Blue tooth connections cannot be established from the other component when this unit is in ECO standby (+ P. 5).

• When using an already-paired smartphone with the NFC function, holding it over the NFC mark establishes a Bluetooth connection.

NFC mark

AUX

USB

CD

RADIO

15:30



15:30



BT

_____

LISTENING TO MUSIC FROM YOUR Bluetooth COMPONENT

12 En

If any of the following operations are performed while a Bluetooth connection is being used, the Bluetooth connection will be

disconnected.

• Hold down source button on this unit or on the remote control.

• Turn the unit off.

• Turn off the Bluetooth setting of the other component.

• Hold the smartphone with the NFC function over the NFC mark during Bluetooth connection.

DAB (Digital Audio Broadcasting) and DAB

+

use digital signals for clearer sound and more stable reception compared to

analog signals.

DAB

+

is based on the original DAB standard but uses a more efficient audio codec.

DAB and DAB

+

are broadcast in blocks of data called “ensembles” containing up to several radio stations that are

simultaneously broadcast.

DAB and DAB

+

can also include an extensive amount of text information, enabling you to select a station by name.

Other information, such as the ensemble name or the status of the digital signal, can be displayed on the front panel display.

“DAB” described in this manual may also refer to “DAB

+

”.

Before tuning into DAB stations, an initial scan must be performed. When you select the DAB for the first time, the initial

scan is performed automatically.

To listen to a DAB station, connect the antenna (+ P. 3).

 Performing the initial scan again (remote control only)

Disconnecting a Bluetooth connection

LISTENING TO DAB STATIONS (TSX-B235D only)

Preparing for DAB reception

Press the RADIO source button to switch the

audio source to DAB.

The initial scan starts. During the scan, the degree of

progress is displayed on the front panel display.

When scan is completed, the number of receivable DAB

stations appear on the front panel display.

If the initial scan is performed, stored DAB station information

and preset DAB stations are cleared.

1 Press and hold down MEMORY on the

remote control.

“DAB INIT SCAN” will appear and

“Press MEMORY” will blink.

2 Press MEMORY.

The initial scan starts.

AUX

USB

CD

RADIO

1 2

13 En

LISTENING TO DAB STATIONS (TSX-B235D only)

English

 Display information (remote control only)

 DAB frequency information

This unit can receive Band III only.

Selecting DAB stations

1 Press the RADIO source button to switch

the audio source to DAB.

2 Press TUNING / to select the DAB

station.

While receiving DAB, DAB station information is

shown on the front panel display.

If the unit does not receive a DAB signal, “Off Air” is

displayed instead of the DAB station name.

1 Secondary indicator:

Some stations have sub (secondary) stations.

If a secondary station is playing, the secondary

indicator is displayed.

2 Signal strength indicator:

Shows current signal strength.

3 Preset number

4 DAB station name

If you press DISPLAY on the remote control, the

information shown on the front panel display will be

switched in the following order.

- STATION LABEL, PRESET NUMBER

- DLS (Dynamic Label Segment)

- ENSEMBLE LABEL

- CHANNEL/FREQ (Channel label and frequency)

- SIGNAL QUALITY

- AUDIO FORMAT (Audio format, DRC)

Frequency Channel label Frequency Channel label Frequency Channel label

174.928 5A 197.648 8B 220.352 11C

176.640 5B 199.360 8C 222.064 11D

178.352 5C 201.072 8D 223.936 12A

180.064 5D 202.928 9A 225.648 12B

181.936 6A 204.640 9B 227.360 12C

183.648 6B 206.352 9C 229.072 12D

185.360 6C 208.064 9D 230.784 13A

187.072 6D 209.936 10A 232.496 13B

188.928 7A 211.648 10B 234.208 13C

190.640 7B 213.360 10C 235.776 13D

192.352 7C 215.072 10D 237.488 13E

194.064 7D 216.928 11A 239.200 13F

195.936 8A 218.640 11B

AUX

USB

CD

RADIO

1

2

10:30

DAB01STATION1

1 2

43

LISTENING TO DAB STATIONS (TSX-B235D only)

14 En

Use the preset function to store your favorite 30 stations.

 Deleting a stored preset

Presetting DAB stations (remote control only)

1 Press the RADIO source button to switch

the audio source to DAB.

2 Press TUNING / to select a station that

you want to preset.

3 Press MEMORY.

The display will indicate “PRESET MEMORY,” and

the preset number will blink.

4 Press PRESET / to select the preset

number that you want to store.

• The lowest preset number that has not been stored will be

selected first.

• If you want to cancel the presetting, press .

• If you select a preset number in which a station has already

been stored, it will be overwritten by the new station.

5 Press MEMORY.

This stores the DAB station.

When presetting has finished, the display will indicate

“Completed!”.

1 Press the RADIO source button to switch

the audio source to DAB.

2 Press MEMORY on the remote control.

The display will indicate “PRESET MEMORY,” and

the preset number will blink.

3 Press TUNING

/

to select the preset

delete operation.

The display will indicate “PRESET DELETE”.

4 Press PRESET / to select the preset

number that you want to delete.

If you want to cancel the deleting, press .

5 Press MEMORY to complete the operation.

The preset will be deleted, and the display will

indicate “Deleted!”.

Selecting preset DAB stations

1 Press the RADIO source button to switch

the audio source to DAB.

2 Press PRESET / to select the DAB

station that you want to hear.

You can only select presets that have been stored.

4

2

53

1

4

3

52

1

AUX

USB

CD

RADIO

1

2

15 En

English

To listen to the FM station, connect the antenna (+ P. 3).

 Display information (remote control only)

If you press DISPLAY on the remote control, the information shown on the front panel display will be switched in the

following order.

LISTENING TO FM STATIONS

Selecting an FM station

1 Press the RADIO source button to switch the

audio source to FM.

2 Tune FM stations

Automatic tuning: Press and hold TUNING /.

Manual tuning: Press TUNING / repeatedly.

If you tune to a station manually while receiving FM, the sound

will be monaural.

Preset number and frequency

Reception status*

* Example of reception status indication.

TUNED/STEREO: A strong FM stereo broadcast is

being received.

TUNED/MONO: A monaural FM broadcast is being

received (even if the FM broadcast is

stereo, reception will be monaural if

the signal is weak).

Not TUNED: No broadcast is being received.

Displaying Radio Data System information

If you press DISPLAY on the remote control while Radio

Data System information is being received, the information

shown on the front panel display will be switched in the

following order.

- PS (Program Service)

- PTY (Program Type)

- RT (Radio Text)

- CT (Clock Time)

- Reception status

- Preset number and frequency

If the signal transmission of the Radio Data System station is too

weak, this unit may not be able to receive Radio Data System

information completely. In particular, RT (Radio Text) information

uses a lot of bandwidth, so it may be less available compared to

other types of information.

AUX

USB

CD

RADIO

1

2

LISTENING TO FM STATIONS

16 En

Use the preset function to store your favorite 30 stations.

First, press the RADIO source button to switch the audio source to FM.

 Auto preset

This method tunes automatically, and automatically presets only the stations that have good reception.

 Manual preset

 Deleting a stored preset

Presetting FM stations (remote control only)

1 Press and hold down MEMORY.

“AUTO PRESET” will appear and “Press MEMORY”

will blink.

2 Press MEMORY.

Auto preset will begin.

When presetting has finished, the display will indicate

“Completed!”.

When you perform auto preset, all stored stations are cleared

and the new stations are stored.

If you want to stop auto preset before it is completed, press .

1 Press TUNING / to tune a station that

you want to preset.

2 Press MEMORY.

The display will indicate “PRESET MEMORY,” and the

preset number will blink.

3 Press PRESET / to select the preset

number that you want to store.

• The lowest preset number that has not been stored will be

selected first.

• If you want to cancel the presetting, press .

• If you select a preset number in which a station has already

been stored, it will be overwritten by the new station.

4 Press MEMORY.

When presetting has finished, the display will indicate

“Completed!”.

1 Press MEMORY on the remote control.

The display will indicate “PRESET MEMORY”, and the

preset number will blink.

2 Press TUNING

/

to select the preset

delete operation.

The display will indicate “PRESET DELETE”.

3 Press PRESET / to select the preset

number that you want to delete.

If you want to cancel the deleting, press .

4 Press MEMORY to complete the operation.

The preset will be deleted, and the display will indicate

“Deleted!”.

AUTO PRESET



Press MEMORY

1 2

PRESETMEMORY

FM0187.50MHz

3

1

42

3

2

41

17 En

LISTENING TO FM STATIONS

English

Selecting preset FM stations

1 Press the RADIO source button to switch the

audio source to FM.

2 Press PRESET / to select the FM station

that you want to hear.

You can only select presets that have been stored.

AUX

USB

CD

RADIO

1

2

18 En

The unit includes an alarm function that plays back audio sources or a set of beep (internal alarm sound) at the set time using

a variety of different methods. The alarm function has the following features.

 3 types of alarms

Select from 3 alarm types, combining music and beep sounds.

 Various audio sources

You can choose from audio CD, data CD, USB device, or DAB

*

/FM. The following playback methods can also be selected

depending on the audio source:

* TSX-B235D only

You can not choose Bluetooth and AUX as the audio source.

Snooze

The snooze function can be enabled to replay the alarm after 5 minutes (+ P. 20).

USING THE ALARM FUNCTION (IntelliAlarm)

SOURCE+BEEP

The selected audio source and the beep sound are played at the set time.

Source playback begins to fade in 3

minutes before the set time and the volume gradually increases to the set volume. Then, at the set time, the

beep sound is activated.

SOURCE

The selected audio source is played at the set time. The volume fades in gradually and increases to the set

volume.

BEEP The beep sound is played at the set time.

Source

Playback

method

Function

Audio CD

Selected track The selected track is played repeatedly.

Resume The track you listened to last time is played back.

Data CD/USB device

Folder The selected folder is played repeatedly.

Resume The track you listened to last time is played back.

DAB

*

/FM

Preset station The selected preset station is played.

Resume

The DAB

*

/FM station you listened to last time is played back.

La pagina sta caricando ...

Yamaha TSX-B235 Black Manuale utente

Yamaha TSX-B235 Black Manuale utente

in altre lingue

Documenti correlati

Altri documenti