3com Switch 4210 PWR 18-Port Manuale utente

3Com

®

Switch 4210 Family

Getting Started

Switch 4210 PWR 9-Port

Switch 4210 PWR 18-Port

Switch 4210 PWR 26-Port

Switch 4210 9-Port

Switch 4210 18-Port

Switch 4210 26-Port

Switch 4210 52-Port

www.3Com.com

Part Number: 10016119 Rev. AB

Published: January, 2008

3Com Corporation

350 Campus Drive

Marlborough, MA

USA 01752-3064

form or by any means or used to make any derivative work (such as translation, transformation, or adaptation) without

written permission from 3Com Corporation.

3Com Corporation reserves the right to revise this documentation and to make changes in content from time to time

without obligation on the part of 3Com Corporation to provide notification of such revision or change.

3Com Corporation provides this documentation without warranty, term, or condition of any kind, either implied or

expressed, including, but not limited to, the implied warranties, terms or conditions of merchantability, satisfactory quality,

and fitness for a particular purpose. 3Com may make improvements or changes in the product(s) and/or the program(s)

described in this documentation at any time.

If there is any software on removable media described in this documentation, it is furnished under a license agreement

included with the product as a separate document, in the hard copy documentation, or on the removable media in a

directory file named LICENSE.TXT or !LICENSE.TXT. If you are unable to locate a copy, please contact 3Com and a copy will

be provided to you.

UNITED STATES GOVERNMENT LEGEND

If you are a United States government agency, then this documentation and the software described herein are provided to

you subject to the following:

All technical data and computer software are commercial in nature and developed solely at private expense. Software is

delivered as “Commercial Computer Software” as defined in DFARS 252.227-7014 (June 1995) or as a “commercial item”

as defined in FAR 2.101(a) and as such is provided with only such rights as are provided in 3Com’s standard commercial

license for the Software. Technical data is provided with limited rights only as provided in DFAR 252.227-7015 (Nov 1995) or

FAR 52.227-14 (June 1987), whichever is applicable. You agree not to remove or deface any portion of any legend provided

on any licensed program or documentation contained in, or delivered to you in conjunction with, this User Guide.

Unless otherwise indicated, 3Com registered trademarks are registered in the United States and may or may not be registered

in other countries.

3Com and the 3Com logo are registered trademarks of 3Com Corporation.

Cisco is a registered trademark of Cisco Systems, Inc.

Funk RADIUS is a registered trademark of Funk Software, Inc.

Aegis is a registered trademark of Aegis Group PLC.

Intel and Pentium are registered trademarks of Intel Corporation. Microsoft, MS-DOS, Windows, and Windows NT are

registered trademarks of Microsoft Corporation. Novell and NetWare are registered trademarks of Novell, Inc. UNIX is a

registered trademark in the United States and other countries, licensed exclusively through X/Open Company, Ltd.

IEEE and 802 are registered trademarks of the Institute of Electrical and Electronics Engineers, Inc.

All other company and product names may be trademarks of the respective companies with which they are associated.

ENVIRONMENTAL STATEMENT

It is the policy of 3Com Corporation to be environmentally-friendly in all operations. To uphold our policy, we are committed

to:

Establishing environmental performance standards that comply with national legislation and regulations.

Conserving energy, materials and natural resources in all operations.

Reducing the waste generated by all operations. Ensuring that all waste conforms to recognized environmental standards.

Maximizing the recyclable and reusable content of all products.

Ensuring that all products can be recycled, reused and disposed of safely.

Ensuring that all products are labelled according to recognized environmental standards.

Improving our environmental record on a continual basis.

End of Life Statement

3Com processes allow for the recovery, reclamation and safe disposal of all end-of-life electronic components.

Regulated Materials Statement

3Com products do not contain any hazardous or ozone-depleting material.

CONTENTS

ABOUT THIS GUIDE

Download the Latest Software and Documentation for Your 3Com Switch 5

Before You Start 5

Related Documentation 6

1 PRODUCT INTRODUCTION

Overview 7

Introduction to the Switch 4210 Family PWR Switches 8

Introduction to the Switch 4210 Family Non-PWR Models 14

Technical Specifications 19

SFP Modules Supported for the Switch 4210 21

2 INSTALLING THE SWITCH

Rack-Mounting the Switch 24

Mounting the Switch on a Desktop 27

The Power-up Sequence 27

Connecting a Redundant Power Supply 28

Connecting the Console Cable 32

3 MANAGING YOUR SWITCH

Methods of Managing a Switch 36

Setting Up Your Switch 37

Viewing Automatically Configured IP Information 40

Manually Configuring IP Information 42

Setting Up Command Line Interface Management 47

Setting Up Command Line Interface Management using SSH 48

Setting Up Web Interface Management 48

Setting Up SNMP Management 49

Default Users and Passwords 50

4 PROBLEM SOLVING

Solving Problems Indicated by LEDs 52

Solving Hardware Problems 53

Solving Communication Problems 54

Solving Fabric Formation Problems 55

A PIN-OUTS

Null Modem Cable 57

PC-AT Serial Cable 57

Modem Cable 58

Ethernet Port RJ-45 Pin Assignments 58

B OBTAINING SUPPORT FOR YOUR 3COM PRODUCTS

Register Your Product to Gain Service Benefits 59

Solve Problems Online 59

Purchase Extended Warranty and Professional Services 59

Access Software Downloads 59

Contact Us 60

C 3COM NETWORK MANAGEMENT

3Com Network Supervisor 63

3Com Network Director 63

3Com Network Access Manager 64

3Com Enterprise Management Suite 65

Integration Kit with HP OpenView Network Node Manager 65

D REDUNDANT POWER SUPPLY SAFETY INFORMATION

Important Safety Information 67

L’information de Sécurité Importante 68

Wichtige Sicherheitsinformationen 68

Información de Seguridad Importante 69

Importanti Informazioni di Sicurezza 71

Wa¿ne informacje o zabezpieczeniach 71

Regulatory Notices 73

ABOUT THIS GUIDE

Download the Latest

Software and

Documentation for

Your 3Com Switch

Thank you for purchasing a 3Com Switch 4210. As part of our commitment to

bringing you the most capable and dependable network equipment, 3Com offers

free software maintenance updates and documentation updates on our website.

To obtain the most up-to-date operating software and user documentation for the

Switch 4210, point your web browser to: www.3Com.com/4210 and select the

“Support and Registration” link.

You must register your 3Com switch before receiving software upgrades. To

register, point your web browser to eSupport.3Com.com.

Before You Start The guide is intended for use by network administrators who install and set up

network equipment; consequently, it assumes a basic working knowledge of LANs

(Local Area Networks).

Release Notes The Release Notes provide important information about the current software

release, including new features, modifications, and known problems. You should

read the Release Notes before installing the switch in your network.

If the information in the Release Notes differs from this guide, follow the

instructions in the Release Notes.

User guides and release notes are available in Adobe Acrobat Reader Portable

Document Format (PDF) on the 3Com World Wide Web site at

http://www.3com.com

Conventions Table 1 lists important conventions that are used throughout this guide.

Table 1 Notice Icons

Icon Notice Type Description

Information note Information that describes important features or

instructions

Caution Information that alerts you to potential loss of data or

potential damage to an application, system, or device

Warning Information that alerts you to potential personal injury

6 ● 3Com Switch 4210 Family

Command Reference

In addition to this guide, the Switch 4210 documentation set includes the following:

■ 3Com Switch 4210 Family Configuration Guide

This guide contains information on the features supported by your switch and

how they can be used to optimize your network. It is supplied in PDF format on

the 3Com Web site.

■ 3Com Switch 4210 Family Command Reference Guide

This guide provides detailed information about the web interface and command

line interface that enable you to manage the switch. It is supplied in PDF format on

the 3Com Web site.

■ Release Notes

These notes provide information about the current software release, including

new features, modifications, and known problems. The release notes are supplied

in hard copy with your switch.

1

PRODUCT INTRODUCTION

Overview The 3Com Switch 4210 Family provides high-performance, high-density,

easy-to-install, NMS-manageable intelligent Ethernet switches that support

wire-speed Layer 2 switching.

Three of the Switch 4210 Family models support industry standard IEEE 802.3af

Power over Ethernet (PoE). Figure 1 displays these models and Table 1 provides a

description of their features.

Figure 1 Power over Ethernet models

Three of the Switch 4210 Family models are available for simple connectivity

without PoE. Figure 2 displays these models and Table 2 describes its features.

Figure 2 Non Power over Ethernet models

Table 1 Power over Ethernet models

Model Power supply

Number of

10/100 Mbps

ports

Number of 1000

Mbps uplink

ports

Number of

Console

ports

Switch 4210 PWR

9-port

AC input 8 One Combo port 1

Switch 4210 PWR

18-port

AC input 16 Two Combo ports 1

Switch 4210 PWR

26-port

AC or RPS DC

input

24 1 (on rear)

8 CHAPTER 1: PRODUCT INTRODUCTION

Introduction to the

Switch 4210 Family

PWR Switches

Switch 4210 9-port PWR Front panel

Each Switch 4210 9-port PWR unit provides eight 10/100Base-TX autosensing

Ethernet ports, one 10/100/1000Base-T Ethernet port, one 100/1000Base SFP

ports, and one Console port. The SFP port and the 10/100/1000BASE-T Ethernet

port form a Combo port. You can use either the SFP port or the

10/100/1000BASE-T Ethernet port at one time.

Figure 3 shows the front panel of a Switch 4210 9-port PWR.

Figure 3 Front panel of a Switch 4210 9-port PWR

Tabl e 2 Non Power over Ethernet models

Model Power supply

Number of

10/100 Mbps

ports

Number of 1000 Mbps

uplink ports

Number of

Console

ports

Switch 4210

9-port

AC input 8 One Combo port 1

Switch 4210

18-port

AC input 16 Two Combo ports 1

Switch 4210

26-port

AC input 24 Two Combo ports 1

Switch 4210

52-port (not

shown)

AC input 48 Two 10/100/100 ports

Two SFP ports

1

(1) 10/100Base-TX autosensing Ethernet port status LED

(2) Link LED for Combo port (3) Console port

(4) Power LED (PWR) (5) A/L LED

(6) D/S LED (7) Mode button

(8) Active LED for Combo port

( 1 ) ( 2 ) ( 3 ) ( 4 )

( 5 ) ( 6 ) ( 7 ) ( 8 )

4

5

1

8

Introduction to the Switch 4210 Family PWR Switches 9

Rear panel

Figure 4 The Switch 4210 9-port PWR model’s rear panel

Side panel

Each Switch 4210 9-port PWR provides a security slot through which you can lock

the device together with an irremovable object to prevent theft. The security slot is

located on the left side panel, as shown in Figure 7.

n

If the left screw hole above the security slot is used, the security slot cannot be

used.

Power system

Switch 4210 PWR 9-port units are able to power attached devices using standard

802.3af Power over Ethernet. The total available power for PoE on this model is

70W, enough to power four ports at full 15.4W required of the PoE standard.

Each Switch 4210 9-port PWR unit supports AC input.

■ Rated Voltage Range: 100 VAC to 240 VAC, 50 Hz/60 Hz

■ Input voltage range: 90 VAC to 264 VAC, 47 HZ to 63 Hz

Cooling system

The Switch 4210 9-port PWR units each run two fans for heat dissipation.

Switch 4210 PWR

18-port

Front panel

Switch 4210s 18-port PWR each provide sixteen 10/100Base-TX autosensing

Ethernet ports, two 10/100/1000Base-T Ethernet ports, two 100/1000Base SFP

ports, and one Console port. Each SFP port and the corresponding

10/100/1000BASE-T Ethernet port form a Combo port. For each Combo port,

either the SFP port or the corresponding 10/100/1000BASE-T Ethernet port can be

used at a time.

Figure 5 shows the front panel of a Switch 4210 18-port PWR.

( 1 )

(1) AC power socket (

10 CHAPTER 1: PRODUCT INTRODUCTION

Figure 5 Front panel of a Switch 4210 18-port PWR

Rear panel

Figure 6 Rear panel of a Switch 4210 18-port PWR

Side panel

Each Switch 4210 18-port PWR provides a security slot, through which you can

lock the device together with an irremovable object to prevent theft. The security

slot is located on the left side panel, as shown in Figure 7.

(1) 10/100Base-TX autosensing Ethernet port status LED

(2) Link LED for Combo port (3) Console port

(4) Power LED (PWR) (5) A/L LED

(6) D/S LED (7) Mode button

(8) Active LED for Combo port

(1) (2) (3) (4)

(5)(6)(7)(8)

( 1 )

(1) AC power socket

Introduction to the Switch 4210 Family PWR Switches 11

Figure 7 Security slot on left side panel of a Switch 4210 18-port PWR

n

If the left screw hole above the security slot is used, the security slot cannot be

used.

Power system

Switch 4210 18-port PWR units support AC input.

■ Rated Voltage Range: 100 VAC to 240 VAC, 50 Hz/60 Hz

■ Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz

Switch 4210 PWR 18-Port units are able to power attached devices using standard

802.3af Power over Ethernet. The total available power for PoE on this model is

135W; enough to power 8-Ports at full 15.4W required of the PoE standard.

Cooling system

Switch 4210s 18-port PWR each run two fans for heat dissipation.

Switch 4210 PWR

26-port

Front panel

The Switch 4210 26-port PWR model provides 24 10/100Base-TX autosensing

Ethernet ports, two 10/100/1000Base-T Ethernet ports, two 100/1000Base SFP

ports, and one Console port. Each SFP port and the corresponding

10/100/1000BASE-T Ethernet port form a Combo port. For each Combo port, you

can use either the SFP port or the corresponding 10/100/1000BASE-T Ethernet

port at one time.

Figure 8 shows the front panel of the Switch 4210 26-port PWR model.

(1): Security slot

(1)

12 CHAPTER 1: PRODUCT INTRODUCTION

Figure 8 The Switch 4210 26-port PWR model’s front panel

Rear panel

Figure 9 Rear panel of a Switch 4210 26-port PWR

Power system

Switch 4210 26-port PWR units support AC input or DC input.

■ AC input

■ Rated voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz

■ Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz

■ DC input—Rated voltage range: -52 VDC to -56 VDC

n

Switch 4210 PWR 26-Port units are able to power attached devices using standard

802.3af Power over Ethernet. The total available power for PoE on this model is

370W; enough to power 24-Ports at full 15.4W required of the PoE standard.

3Com recommends a Redundant Power System (RPS) from Eaton Powerware for

providing DC power to the Switch 4210 PWR 26-Port. For full details, refer to

www.3com.com/rps.

Cooling system

Switch 4210 26-port PWR units each run four fans for heat dissipation.

(1) (2) (3) (4)

(5)(6)(7)(8)

(1) 10/100Base-TX autosensing Ethernet port status LED

(2) Link LED for Combo port (3) Console port

(4) Power LED (PWR) (5) A/L LED

(6) D/S LED (7) Mode button

(8) Active LED for Combo port

(1) (2) (3)

(1) AC power socket (2) DC power socket

(3) Grounding screw

Introduction to the Switch 4210 Family PWR Switches 13

The Switch 4210 PWR

Front Panel LEDs

Power LED

Table 3 describes the power LED on the Switch 4210 PWR model.

10/100BASE-TX Autosensing Ethernet Port Status LED

There are two port status LEDs on both sides (yellow LED on the left and green LED

on the right) of the 10/100BASE-TX Ethernet port on the Switch 4210 PWR

models. They indicate the port’s active, link, duplex, and speed status.

In addition, there is an A/L LED and a D/S LED on each Switch 4210 PWR model.

These two LEDs indicate the port status LEDs mode. When the A/L LED is on, the

port status LEDs respectively indicate the port’s active status and link status. When

the D/S LED is on, the port status LEDs respectively indicate the port’s duplex status

and speed status. Either the A/L LED or the D/S LED is on at one time. For details,

see Table 4.

You can change the mode of the port status LEDs by pressing the Mode button.

After a switch is powered on, the A/L LED is on initially. If you press the Mode

button, the D/S LED will be on. After that, if you press the Mode button again

within 45 seconds, the A/L LED will be on again. Otherwise, the A/L LED will

automatically be on 45 seconds later.

1000 Mbps Uplink Port Status LED

Table 5 describes the 1000 Mbps upline port status LED on the Switch 4210.

Table 3 The power LED on the Switch 4210 PWR models

LED Mark on the panel Status Description

Power LED PWR ON The switch is powered on.

OFF The switch is powered off.

Table 4 Port status LEDs on the Switch 4210 PWR models

Port status

mode LED Port status LED Description

The A/L LED is

on

Yellow LED

(left)

BLINKING The port is in the active state and there is

traffic on the port.

OFF The port is in the active state but there is no

traffic on the port.

Green LED

(right)

ON The port is connected properly.

OFF The port is not connected or is incorrectly

connected.

The D/S LED is

on

Yellow LED

(left)

ON The port operates in the full duplex mode.

OFF The port operates in the half duplex mode.

Green LED

(right)

ON The port rate is 100 Mbps.

OFF The port rate is 10 Mbps.

Table 5 The 1000 Mbps uplink port status LED on 4210 PWR models

LED

Mark on the

panel Status Description

1000 Mbps uplink port

link LED

LINK ON The port is connected properly.

OFF The port is not connected or is

incorrectly connected.

14 CHAPTER 1: PRODUCT INTRODUCTION

Introduction to the

Switch 4210 Family

Non-PWR Models

This section describes each Switch 4210 Family model.

Switch 4210 9-port Front panel

The Switch 4210 9-port model provides eight 10/100Base-TX autosensing

Ethernet ports, one 10/100/1000Base-T autosensing Ethernet port, one

100/1000Base-X SFP port, and one Console port. The SFP port and the

10/100/1000BASE-T autosensing Ethernet port form a Combo port. For the

Combo port, either the SFP port or the 10/100/1000BASE-T Ethernet port can be

used at a time.

Figure 10 shows the front panel of the Switch 4210 9-port model.

Figure 10 The Switch 4210 9-port model’s front panel

.

1000 Mbps uplink port

active LED

ACT BLINKING The port is in the active state and

there is traffic on the port.

OFF The port is in the active state but

there is no traffic on the port.

Tabl e 5 The 1000 Mbps uplink port status LED on 4210 PWR models

LED

Mark on the

panel Status Description

(1) 10/100Base-TX autosensing port Speed LED (green)

(2) 10/100Base-TX autosensing port (3) Combo port Speed LED (green)

(4) 10/100/1000Base-T autosensing port (5) Console port

(6) 100/1000Base-X SFP port (7) Link/Act LED (green)

(8) Power LED (PWR)

(

1

)

(

2

)

(

4

)

(

5

)

(

6

)

(

7

)

(

8

)

(

3

)

(

7

)

Introduction to the Switch 4210 Family Non-PWR Models 15

Rear panel

Figure 11 The Switch 4210 9-port model’s rear panel

Power system

The Switch 4210 9-port model supports AC input.

■ Rated Voltage Range: 100 VAC to 240 VAC, 50 Hz/60 Hz

■ Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz

Cooling system

The Switch 4210 cools off naturally.

Switch 4210 18-port Front panel

The Switch 4210 18-port models provide 16 10/100Base-TX autosensing Ethernet

ports, two 10/100/1000Base-T autosensing Ethernet ports, two 100/1000Base-X

SFP ports, and one Console port. Each SFP port and the corresponding

10/100/1000BASE-T autosensing Ethernet port form a Combo port. For each

Combo port, you can use either the SFP port or the corresponding

10/100/1000BASE-T Ethernet port at one time.

Figure 12 shows the Switch 4210 18-port model’s front panel.

Figure 12 The Switch 4210 18-port model’s front panel

AC input terminal block

(1) (2)

(4)

(5)(6)

(7)

(8)

(3)

(7)

(1) 10/100Base-TX autosensing port Speed LED (green)

(2) 10/100Base-TX autosensing port (3) Combo port Speed LED (green)

(4) 10/100/1000Base-T autosensing port (5) Console port

(6) 100/1000Base-X SFP port (7) Link/Act LED (green)

(8) Power LED (PWR)

16 CHAPTER 1: PRODUCT INTRODUCTION

Rear panel

Figure 13 The Switch 4210 18-port model’s rear panel

Power system

The Switch 4210 18-port model’s support AC input.

■ Rated Voltage Range: 100 VAC to 240 VAC, 50 Hz/60 Hz

■ Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz

Cooling system

3Com Switch 4210 non-PWR models cool naturallly through airflow.

Switch 4210 26-port Front panel

The Switch 4210 26-port front panel provides 24 10/100Base-TX autosensing

Ethernet ports, two 10/100/1000Base-T autosensing Ethernet ports, two

100/1000Base-X SFP ports, and one Console port. Each SFP port and the

corresponding 10/100/1000BASE-T autosensing Ethernet port form a Combo

port. For each Combo port, you can use either the SFP port or the corresponding

10/100/1000BASE-T Ethernet port at one time.

Figure 14 shows the front panel of the Switch 4210 26-port model.

Figure 14 The Switch 4210 26-port front panel

AC input terminal block

(1) (2) (4)

(5)(6)

(7)(8)

(3)

(7)

(1) 10/100Base-TX autosensing port Speed LED (green)

(2) 10/100Base-TX autosensing port (3) Combo port Speed LED (green)

(4) 10/100/1000Base-T autosensing port (5) Console port

(6) 100/1000Base-X SFP port (7) Link/Act LED (green)

(8) Power LED (PWR)

Introduction to the Switch 4210 Family Non-PWR Models 17

Rear panel

Figure 15 The Switch 4210 26-port rear panel

Power system

The Switch 4210 26-port model supports AC input.

■ Rated Voltage Range: 100 VAC to 240 VAC, 50 Hz/60 Hz

■ Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz

Cooling system

3Com Switch 4210 non-PWR models cool naturally through airflow.

Switch 4210 52-port Front Panel

The Switch 4210 52-port front panel provides 48 10/100Base-TX autosensing

Ethernet ports, two 10/100/1000Base-T autosensing Ethernet ports, two

100/1000Base-X SFP ports (The 4 gigabit ports are all active), and one Console

port. Each SFP port and the corresponding 10/100/1000BASE-T autosensing

Ethernet port form a Combo port. For each Combo port, you can use either the

SFP port or the corresponding 10/100/1000BASE-T Ethernet port at one time. The

Switch 4210 52-port unit is displayed in Figure 16.

Figure 16 Switch 4210 52-port unit

Power system

The Switch 4210 52-port model supports AC input.

■ Rated Voltage Range: 100 VAC to 240 VAC, 50 Hz/60 Hz

■ Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz

Cooling system

3Com Switch 4210 non-PWR models cool naturally through airflow.

( 2 )

(2) AC input terminal block

18 CHAPTER 1: PRODUCT INTRODUCTION

Switch 4210 Family

Front Panel LEDs

Power LED

Table 6 describes the power LED on the Switch 4210.

Port LED

Table 7 describes the 10/100Base-TX autosensing port’s Link/Act LED.

Table 8 describes the Speed LED on the 10/100Base-TX port.

For a description of the Link/Act LED of the Combo port, see Table 7. When the

port is connected correctly, the Speed LED indicates the operating speeds of the

Combo port, as shown in Table 9.

Tabl e 6 The power LED on the Switch 4210

LED Mark on the panel Status Description

Power LED Power ON The switch is powered on.

OFF The switch is powered off.

Tabl e 7 The Link/Act LED on the 3Com Switch 4210

LED Status Description

Link/Act LED (green) ON The port is connected properly.

BLINKING The port is in the active state and there is

traffic on the port.

OFF The port is not connected or is incorrectly

connected.

Tabl e 8 The 10/100Base-TX port Speed LED on the Switch 4210

LED Status Description

10/100Base-TX autosensing

port Speed LED (green)

ON The port is operating at 100 Mbps.

OFF The port is operating at 10 Mbps.

Tabl e 9 The Combo port Speed LED on the Switch 4210

LED Operating port Status Description

Combo port

Speed LED

(green)

100/1000Base-X

SFP port

Connected

to a 1000

Mbps optical

module

ON The port is operating at

1000 Mbps.

Connected

to a 100

Mbps optical

module

OFF The port is operating at

100 Mbps.

10/100/1000Base-T autosensing

port

ON The port is operating at

1000 Mbps.

OFF The port is operating at

10/100 Mbps.

Technical Specifications 19

Technical

Specifications

Tabl e 10 Technical specifications for the Switch 4210

Model Switch 4210 52-port Switch 4210 26-port Switch 4210 18-port Switch 4210 9-port

Physical dimensions (H

× W × D)

43.6 x 440 x 225 mm

(1.7 x 17.3 x 8.8 in.)

43.6 × 440 × 160 mm

(1.7 × 17.3 × 6.3 in.)

43.6 × 360 × 160 mm

(1.7 × 14.2 × 6.3 in.)

43.6 × 230 × 160 mm

(1.7 × 9.1 × 6.3 in.)

Weight 12.1 lbs (5.5 Kgs) 4.7 lbs (2.14 Kgs) 3.4 lbs (1.53 kg.) 2.3 lbs (1.06 kg.)

Number of fixed ports 48 x 10/100Base-TX

autosensing Ethernet

port

4 x 100/1000 Mps

Combo ports

24 × 10/100Base-TX

autosensing Ethernet

ports

2 × 100/1000 Mbps

Combo ports

16 × 10/100Base-TX

autosensing Ethernet

ports

2 × 100/1000 Mbps

Combo ports

8 × 10/100Base-TX

autosensing Ethernet

ports

1 × 100/1000 Mbps

Combo port

Number of

management ports

1 × Console port

Power system AC input:

■ Rated voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz

■ Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz

PoE (to power attachd

deices)

Not supported Not supported Not supported Not supported

System power

consumption (full

load)

25W 16W 12W 10W

Fan None None None None

Operating

temperature

0°C to 45°C (30°F to 113°F)

Relative humidity

(non-condensing)

10% to 90%

Table 11 Technical specifications for the Switch 4210 PWR models

Model

Switch 4210

26-port PWR

Switch 4210

18-port PWR

Switch 4210

9-port PWR

Physical dimensions (H × W

× D)

H 1.7 in 45 mm

W 17.3 in 440 mm

D 16.9 in 430 mm

H 1.7 in 45 mm

W 11.8 in 300 mm

D 9.2 in 233 mm

H 1.7 in 45 mm

W 11.8 in 300 mm

D 10.8 in 275 mm

Weight 13.4 lbs

6.09 Kgs

6.0 lbs

2.70 Kgs

4.9 lbs

2.22 Kgs

Number of fixed ports 24 × 10/100BASE-TX

autosensing Ethernet

ports

2 × 100/1000 Mbps

Combo ports

16 ×

10/100BASE-TX

autosensing

Ethernet ports

2 × 100/1000 Mbps

Combo ports

8 × 10/100BASE-TX

autosensing

Ethernet ports

1 × 100/1000 Mbps

Combo port

Number of management

ports

1 × Console port

20 CHAPTER 1: PRODUCT INTRODUCTION

n

The Switch 4210 26-port, 18-port, and 9-port PWR models provide an

over-temperature protection mechanism. When the internal temperature exceeds

65°C (149

°F), they will stop providing power from all ports. When the temperature

is below 60°C (140

°F), they will continue to provide power from all ports.

Related Standards The 3Com Switch 4210 Family is designed to the following standards:

Earthing Lead

Power system Switch 4210s 26-port PWR support AC input and DC input.

Switch 4210 18-port PWR/Switch 4210s 9-port PWR support only

AC input.

AC input:

■ Rated voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz

■ Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz

DC input:

■ Rated voltage range: -52 VDC to -56 VDC

All ports

serve as PoE

ports

System

power

consumption

(full load)

AC input: 465 W

DC input: 400 W

160 W 95 W

PoE power

maximum

15.4 W × 24 15.4 W × 8 15.4 W × 4

Number of fans 4 2 2

Operating temperature 0°C to 45°C (30°F to 113°F)

Relative humidity

(non-condensing)

10% to 90%

Table 11 Technical specifications for the Switch 4210 PWR models

Model

Switch 4210

26-port PWR

Switch 4210

18-port PWR

Switch 4210

9-port PWR

Function

8802-3, IEEE 802.3 (Ethernet), IEEE 802.3u (Fast Ethernet), IEEE

802.3ab (Gigabit Ethernet), IEEE 802.1D (Bridging)

Safety

UL 60950-1, EN 60950-1, CSA 22.2 No. 60950-1, IEC 60950-1

EMC Emissions

EN55022 Class A, CISPR 22 Class A, FCC Part 15 Subpart B Class

A, ICES-003 Class A, VCCI Class A, EN61000-3-2, EN61000-3-3

EMC Immunity

EN55024

Safety Requirements The Earthing Lead shall comply with the following safety

standards:

UL Subject 758, UL 1581 and CSA C22.2 No. 210

UL VW-1 and CSA FT1 Vertical Flame Test

Voltage Rating 600V

AWG 12

Insulation Thickness 0.4mm

Insulation Color Green/Yellow

La pagina si sta caricando...

3com Switch 4210 PWR 18-Port Manuale utente

3com Switch 4210 PWR 18-Port Manuale utente

in altre lingue

Documenti correlati

Altri documenti