D-Link DES-1316 - Switch Manuale utente

D-Link DES-1316

Web-Smart 8-Port 10/100Mbps Ethernet Switch with 8

10/100Mbps 802.3af Power Over Ethernet Ports

Manual

First edition

Building Networks for People

2

FCC Warning

This equipment has been tested and found to comply with the limits

for a Class A digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with this

manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to correct

the interference at his own expense.

CE Mark Warning

This is a Class A product. In a domestic environment, this product

may cause radio interference in which case the user may be required

to take adequate measures.

Warnung!

Dies ist ein Produkt der Klasse A. Im Wohnbereich kann dieses

Produkt Funkstoerungen verursachen. In diesem Fall kann vom

Benutzer verlangt werden, angemessene Massnahmen zu ergreifen.

Precaución!

Este es un producto de Clase A. En un entorno doméstico, puede

causar interferencias de radio, en cuyo case, puede requerirse al

usuario para que adopte las medidas adecuadas.

Attention!

Ceci est un produit de classe A. Dans un environnement domestique,

ce produit pourrait causer des interférences radio, auquel cas

l`utilisateur devrait prendre les mesures adéquates.

Attenzione!

3

Il presente prodotto appartiene alla classe A. Se utilizzato in ambiente

domestico il prodotto può causare interferenze radio, nel cui caso è

possibile che l`utente debba assumere provvedimenti adeguati.

VCCI Warning

BSMI Warning

4

TABLE OF CONTENTS

About This Guide...........................................................................................6

Purpose........................................................................................................6

Terms/Usage...............................................................................................6

Introduction.....................................................................................................7

Fast Ethernet Technology.........................................................................7

Switching Technology..............................................................................7

VLAN (Virtual Local Area Network)....................................................8

Power over Ethernet (PoE).......................................................................9

Features........................................................................................................9

Unpacking and Installation.........................................................................11

Unpacking.................................................................................................11

Installation.................................................................................................11

Rack Mounting.........................................................................................12

Connecting Network Cable ....................................................................13

AC Power..................................................................................................13

Identifying External Components.............................................................14

Front Panel................................................................................................14

Rear Panel.................................................................................................15

Understanding LED Indicators..................................................................16

Power and CPU LEDs.............................................................................16

Ports 1~8 PoE port status LEDs............................................................16

Ports 9~16 Ethernet port status LEDs ..................................................17

5

Configuration................................................................................................18

Installing the Web Management Utility...............................................18

Discovery List..........................................................................................20

Monitor List..............................................................................................20

Device Setting..........................................................................................22

Toolbar.......................................................................................................25

Configuring the Switch...........................................................................26

Login ..........................................................................................................26

Setup Menu...............................................................................................29

Configuring Setup Setting......................................................................30

Port Settings.........................................................................................30

VLAN Settings (Virtual Local Area Network)..............................32

Trunk Setting .......................................................................................33

Mirror Setting ......................................................................................34

PoE Setting...........................................................................................35

Device Status.......................................................................................36

Statistic..................................................................................................37

System Setting.....................................................................................39

Trap Setting..........................................................................................40

Set Password........................................................................................41

Backup Setting.....................................................................................42

Reset Setting........................................................................................43

Logout........................................................................................................43

Technical Specifications.............................................................................44

6

ABOUT THIS GUIDE

Congratulations on your purchase of the 8-Port 10/100Mbps Ethernet

Web Smart Switch with 8-Port PoE. This Switch integrates 100Mbps

Fast Ethernet and 10Mbps Ethernet network capabilities in a highly

flexible package. Since this Switch’s Port-1 to Port-8 are Power over

Ethernet (PoE) ports, it will automatically detect the presence of IEEE

802.3af-compliant devices and will provide power through Port-1 to

Port-8. The Switch provides 15.4Watts per port and can be connected

to WLAN access point, IP phone, video camera, and other PD devices.

The Switch will automatically detect the network appliance’s

requirements, and the Switch will supply the required power current to

each appliance.

Purpose

This guide discusses how to install your Web-Smart16-Port

10/100Mbps Ethernet Switch.

Terms/Usage

In this guide, the term “Switch” (first letter upper case) refers to your

Web-Smart 8-Port 10/100Mbps Ethernet Web-Smart Switch with 8

10/100Mbps PoE ports and “switch” (first letter lower case) refers to

other Ethernet switches.

7

INTRODUCTION

This chapter describes the features of the Web Smart Switch and some

background information about Ethernet/Fast Ethernet switching

technology.

Fast Ethernet Technology

The growing importance of LANs and the increasing complexity of

desktop computing applications are fueling the need for high

performance networks. A number of high-speed LAN technologies

have been proposed to provide greater bandwidth and improve

client/server response times. Among them, 100BASE-T (Fast Ethernet)

provides a non-disruptive, smooth evolution from the current

10BASE-T technology. The non-disruptive and smooth evolution

nature, and the dominating potential market base, virtually guarantees

cost-effective and high performance Fast Ethernet solutions.

100Mbps Fast Ethernet is a standard specified by the IEEE 802.3

LAN committee. It is an extension of the 10Mbps Ethernet standard

with the ability to transmit and receive data at 100Mbps, while

maintaining the CSMA/CD Ethernet protocol. Since the 100Mbps

Fast Ethernet is compatible with all other 10Mbps Ethernet

environments, it provides a straightforward upgrade and takes

advantage of the existing investment in hardware, software, and

personnel training.

Switching Technology

Another approach to pushing beyond the limits of Ethernet technology

is the development of switching technology. A switch bridges

Ethernet packets at the MAC address level of the Ethernet protocol

8

transmitting among connected Ethernet or Fast Ethernet LAN

segments.

Switching is a cost-effective way of increasing the total network

capacity available to users on a local area network. A switch increases

capacity and decreases network loading by dividing a local area

network into different segments, which do not compete with each

other for network transmission capacity.

The switch acts as a high-speed selective bridge between the

individual segments. The switch, without interfering with any other

segments, automatically forwards traffic that needs to go from one

segment to another. By doing this the total network capacity is

multiplied, while still maintaining the same network cabling and

adapter cards.

Switching LAN technology is a marked improvement over the

previous generation of network bridges, which were characterized by

higher latencies. Routers have also been used to segment local area

networks, but the cost of a router, the setup and maintenance required

make routers relatively impractical. Today switches are an ideal

solution to most kinds of local area network congestion problems.

VLAN (Virtual Local Area Network)

A VLAN is a group of end-stations that are not constrained by their

physical location and can communicate as if a common broadcast

domain, a LAN. The primary utility of using VLAN is to reduce

latency and the need for routers, using faster switching instead. Other

VLAN utilities include:

Security: Security is increased with the reduction of opportunity in

eavesdropping on a broadcast network because data will be switched

to only those confidential users within the VLAN.

9

Cost Reduction: A VLAN can be used to create multiple broadcast

domains, thus eliminating the need of expensive routers.

802.1Q VLAN: The VLAN tagging option is a standard set by the

IEEE to facilitate the spanning of VLANs across multiple switches.

(Reference: IEEE Std 802.1Q-1998 Virtual Bridged Local Area

Networks.)

Power over Ethernet (PoE)

Power over Ethernet (PoE) integrates power and data onto one single

cabling infrastructure, eliminating the need to have AC power

available at all locations.

Power and Data are integrated onto the same cable. Supporting

category 5/5e up to 100 Meters, PoE will provide power to PoE

compatible device, such as IP telephones, wireless LAN access points,

and IP security cameras.

PoE is already widely adopted in the market, saving up to 50% of

overall installation costs by eliminating the need to install separate

electrical wiring and power outlets.

Features

u 8×10/100Mbps Auto-negotiation Fast Ethernet RJ45 ports with 8-

port PoE function (port-1 ~ port-8)

u Compliant with 802.3af specification

u Supports PoE power maximum 15.4W for each PoE port

u Supports PoE Powered Device (PD) classification identify

u Each port supports auto MDI/MDIX, so there is no need to use

cross-over cables or an up-link port

u Full-/half- duplex transfer mode for each port

10

u Wire speed reception and transmission

u Store-and-Forward switching scheme capability to support rate

adaptation and ensure data integrity

u Up to 4K unicast addresses entities per device, self-learning, and

table aging

u 512KBytes packet buffer

u Supports IEEE 802.3x flow control for full-duplex mode ports

u Supports Back-pressure flow control for half-duplex mode ports

u Supports 802.1Q VLAN

u Supports Port based Trunking

u Supports Port-mirroring

u Supports Port-settings for Speed/Duplex, Flow control and Port

based QoS (Quality of Service)

u Easy configuration via Web Browser

u Easy setting via Web Management Utility

u Standard 19” Rack-mount size

11

UNPACKING AND INSTALLATION

This chapter provides unpacking and installation information for the

Switch.

Unpacking

Open the shipping cartons of the Switch and carefully unpacks its

contents. The carton should contain the following items:

One 8-Port 10/100Mbps Ethernet Web Smart Switch with 8-Port PoE

One AC power cord, suitable for your area’s electrical power

connections

Four rubber feet to be used for shock cushioning

Screws and two mounting brackets

CD-ROM with Web Management Utility and Manual

If any item is found missing or damaged, please contact your local

reseller for replacement.

Installation

The site where you install the Switch may greatly affect its

performance. When installing, consider the following pointers:

Install the Switch in a fairly cool and dry place. See Technical

Specifications for the acceptable temperature and humidity operating

ranges.

Install the Switch in a site free from strong electromagnetic field

generators (such as motors), vibration, dust, and direct exposure to

sunlight.

12

Leave at least 10cm of space at the front and rear of the Switch for

ventilation.

Install the Switch on a sturdy, level surface that can support its weight,

or in an EIA standard-size equipment rack. For information on rack

installation, see the next section, titled Rack Mounting.

When installing the Switch on a level surface, attach the rubber feet to

the bottom of each device. The rubber feet cushion the Switch and

protect the case from scratching.

Rack Mounting

The Switch can be mounted in an EIA standard-size, 19-inch rack,

which can be placed in a wiring closet with other equipment. Attach

the mounting brackets at the Switch’s front panel (one on each side),

and secure them with the provided screws.

Figure 1. Combine the Switch with the provided screws.

Then, use screws provided with the equipment rack to mount each

switch in the rack.

Figure 2. Mount the Switch in the rack.

13

Connecting Network Cables

The Switch supports 16 10/100Mbps Ethernet ports and Ports 1 ~ 8

are PoE Enabled ports. These PoE ports will be automatically

activated when a compatible terminal is identified. The Switch will

supply power through the Ethernet port to the connected PoE device.

For Legacy devices that are not yet compatible, the PoE port will not

offer the power to these devices. This feature allows users to freely

and safely mix legacy and Power over LAN compatible devices on

their network.

The Switch supports 10Mbps Ethernet or 100Mbps Fast Ethernet and

it runs both in half- and full- duplex mode using two pairs of Category

5 cables.

These RJ45 ports are Auto-MDI type port. The Switch can auto

transform to MDI-II or MDI-X type, so you can just make an easy

connection without worrying if you are using a standard or crossover

RJ45 cable.

AC Power

The Switch uses the AC power supply 100-240V AC, 50-60 Hz. The

power switch is located at the rear of the unit adjacent to the AC

power connector and the system fan. The Switch’s power supply will

adjust to the local power source automatically and may be turned on

without having any or all LAN segment cables connected.

14

IDENTIFYING EXTERNAL COMPONENTS

This chapter describes the front panel, rear panel, and LED indicators

of the Switch.

Front Panel

The figure below shows the front panels of the Switch.

Figure 3. Front panel of 8-port 10/100 Ethernet Switch with 8-port PoE.

LED Indicator:

Comprehensive LED indicators display the status of the Switch and

the network (see the LED Indicators chapter below).

PoE Ports (Port 1~8):

These ports are PoE Enabled ports. The PoE port will be automatically

activated when a compatible terminal is identified, and the Switch will

supply power through the Ethernet port to the connected PoE device.

For Legacy devices that are not yet compatible, the PoE port will not

offer the power to these devices. This feature allows users to freely

and safely mix legacy and Power over LAN compatible devices on

their network.

These ports support network speeds of either 10Mbps or 100Mbps,

and can operate in half- and full- duplex transfer modes. These ports

also support the automatic MDI/MDIX crossover detection function,

providing true “plug and play” capability. Just plug-in the network

cable to the Switch directly regardless if the end node is a NIC

(Network Interface Card) or switch and hub.

15

Ethernet Ports (Port 9~16):

These ports support network speeds of either 10Mbps or 100Mbps,

and can operate in half- and full- duplex transfer modes. These ports

also support the automatic MDI/MDIX crossover detection function,

providing true “plug and play” capability. Just plug-in the network

cable to the Switch directly regardless if the end node is a NIC

(Network Interface Card) or switch and hub.

Note: When the port is set to “Forced Mode”, Auto MDI/MDIX will

be disabled.

Rear Panel

AC Power Connector

Reset Button

Figure 4. Rear panel of the Switch

AC Power Connector:

This is a three-pronged connector that supports the power cord. Plug

in the female connector of the provided power cord into this connector,

and the male into a power outlet. Supported input voltages range from

100-240V AC at 50-60Hz.

Reset:

The Reset button is to reset all settings back to the factory defaults.

Note: Be sure that you recorded the settings of your device, as all

settings will be erased when pressing the “Reset” button.

16

UNDERSTANDING LED INDICATORS

The front panel LEDs provide instant status feedback, and helps

monitor and troubleshoot when needed.

Figure 5. LED indicators of the Switch

Power and CPU LEDs

POWER: Power Indicator

On :

When the Power LED lights on, the Switch is receiving power.

Off :

When the Power turns off or the power cord has improper connection.

CPU: Management Indicator

Blinking :

When the CPU is working, the CPU LED is blinking.

On/Off :

The CPU is not working.

Ports 1~8 PoE port status LEDs

Link/ACT: Link/Activity

On :

When the Link/ACT LED lights on, the respective port is

successfully

connected to an Ethernet network.

Blinking

:

When the Link/ACT LED

is blinking, the port is transmitting or

receiving data on the Ethernet network.

Off :

There is no link.

17

100Mbps

On :

When the 100Mbps LED lights on, the respective port is connected to a

100Mbps Fast Ethernet network.

Off :

When the respective port is connected to a 10Mbps Ethernet network.

PoE Status

Green :

When the PoE device is

connected and the port supplies power

successfully.

Red :

When the PoE port has the following failures:

ü PoE power short circuit

ü PoE Power over current

ü PoE Power fault

Off :

No Powered Device is detected.

Ports 9~16 Ethernet port status LEDs

Link/ACT: Link/Activity

On :

When the Link/ACT LED lights on, the respective port is

successfully

connected to an Ethernet network.

Blinking

:

When the Link/ACT LED

is blinking, the port is transmitting or

receiving data on the Ethernet network.

Off :

There is no link.

100Mbps

On :

When the 100Mbps LED lights on, the respective port is connected to a

100Mbps Fast Ethernet network.

Off :

When the respective port is connected to a 10Mbps Ethernet network.

18

CONFIGURATION

Through the Web browser you can configure Switch functions such as

VLAN, Trunking, and QoS… etc.

With the attached Web Management Utility, you can easily discover

all the Web Managed Switches, assign IP Addresses, change the

passwords, and upgrade new firmware.

Installing the Web Management Utility

The following instructions guide you through the installation of the

Web Management utility.

1. Insert the Utility CD in the CD-ROM Drive.

2. From the Start menu on the Windows desktop, choose Run.

3. In the Run dialog box, type D:\Web Management

Utility\setup.exe (D:\ depends where your CD-ROM drive is

located) and click OK.

4. Follow the on-screen instructions to install the utility.

5. Upon completion, go to Program Files ->

web_management_utility and execute the Web Management

utility. (Figure 6.)

19

Figure 6. Web Management Utility

The Web Management Utility is divided into four parts, Discovery

List, Monitor List, Device Setting, and Toolbar function, for detailed

instructions, follow the section below.

20

Discovery List

This is the list where you can discover all the Web managed devices

in the entire network.

By pressing the “Discovery” button, you can list all the Web Managed

devices in the discovery list.

Double click or press the “Add to monitor list” button to select a

device from the Discovery List to the Monitor List.

System word definitions in the Discovery List:

l MAC Address: Shows the device MAC Address.

l IP Address: Shows the current IP address of the device.

l Protocol version: Shows the version of the Utility protocol.

l Product Name: Shows the device product name.

l System Name: Shows the appointed device system name.

l Location: Shows where the device is located.

l Trap IP: Shows the IP where the Trap is to be sent.

l Subnet Mask: Shows the Subnet Mask of the device.

l Gateway: Shows the Gateway of the device.

Monitor List

All the Web Smart Devices in the Monitor List can be monitored; you

can also receive the trap and show the status of the devices.

System word definitions in the Monitor List:

La pagina sta caricando ...

D-Link DES-1316 - Switch Manuale utente

Questo manuale è adatto anche per

D-Link DES-1316 - Switch Manuale utente

in altre lingue

Documenti correlati

Altri documenti