Asus PRIME B250M-A Manuale utente

Marca: Asus

Modello: PRIME B250M-A

Categoria: Schede madri

Tipo: Manuale utente

Motherboard

PRIME B250M-A

E11969

First Edition

August 2016

No part of this manual, including the products and software described in it, may be reproduced,

transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any

means, except documentation kept by the purchaser for backup purposes, without the express written

permission of ASUSTeK COMPUTER INC. (“ASUS”).

Product warranty or service will not be extended if: (1) the product is repaired, modied or altered, unless

such repair, modication of alteration is authorized in writing by ASUS; or (2) the serial number of the

product is defaced or missing.

ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS

OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS

DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,

INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,

LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),

EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY

DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.

SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR

INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,

AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO

RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS

MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.

Products and corporate names appearing in this manual may or may not be registered trademarks or

copyrights of their respective companies, and are used only for identication or explanation and to the

owners’ benet, without intent to infringe.

Offer to Provide Source Code of Certain Software

This product contains copyrighted software that is licensed under the General Public License (“GPL”),

under the Lesser General Public License Version (“LGPL”) and/or other Free Open Source Software

Licenses. Such software in this product is distributed without any warranty to the extent permitted by the

applicable law. Copies of these licenses are included in this product.

Where the applicable license entitles you to the source code of such software and/or other additional data,

you may obtain it for a period of three years after our last shipment of the product, either

(1) for free by downloading it from http://support.asus.com/download

(2) for the cost of reproduction and shipment, which is dependent on the preferred carrier and the location

where you want to have it shipped to, by sending a request to:

ASUSTeK Computer Inc.

Legal Compliance Dept.

15 Li Te Rd.,

Beitou, Taipei 112

Taiwan

In your request please provide the name, model number and version, as stated in the About Box of the

product for which you wish to obtain the corresponding source code and your contact details so that we

can coordinate the terms and cost of shipment with you.

The source code will be distributed WITHOUT ANY WARRANTY and licensed under the same license as

the corresponding binary/object code.

This offer is valid to anyone in receipt of this information.

ASUSTeK is eager to duly provide complete source code as required under various Free Open Source

Software licenses. If however you encounter any problems in obtaining the full corresponding source

code we would be much obliged if you give us a notication to the email address [email protected], stating

the product and describing the problem (please DO NOT send large attachments such as source code

archives, etc. to this email address).

iii

Contents

Safety information ...................................................................................... iv

About this guide ......................................................................................... iv

Package contents ....................................................................................... vi

PRIME B250M-A specications summary ................................................ vi

Chapter 1 Product introduction

Motherboard overview ............................................................................. 1-1

Central Processing Unit (CPU) ................................................................ 1-8

System memory ........................................................................................ 1-9

Chapter 2 BIOS information

BIOS setup program ................................................................................. 2-1

EZ Mode ..................................................................................................... 2-2

Advanced Mode ........................................................................................ 2-3

Exit menu ................................................................................................... 2-4

Appendix

Notices .......................................................................................................A-1

ASUS contact information .......................................................................A-5

Safety information

Electrical safety

• To prevent electrical shock hazard, disconnect the power cable from the electrical outlet

before relocating the system.

• When adding or removing devices to or from the system, ensure that the power cables

for the devices are unplugged before the signal cables are connected. If possible,

disconnect all power cables from the existing system before you add a device.

• Before connecting or removing signal cables from the motherboard, ensure that all

power cables are unplugged.

• Seek professional assistance before using an adapter or extension cord. These devices

could interrupt the grounding circuit.

• Ensure that your power supply is set to the correct voltage in your area. If you are not

sure about the voltage of the electrical outlet you are using, contact your local power

company.

• If the power supply is broken, do not try to x it by yourself. Contact a qualied service

technician or your retailer.

Operation safety

• Before installing the motherboard and adding components, carefully read all the manuals

that came with the package.

• Before using the product, ensure all cables are correctly connected and the power

cables are not damaged. If you detect any damage, contact your dealer immediately.

• To avoid short circuits, keep paper clips, screws, and staples away from connectors,

slots, sockets and circuitry.

• Avoid dust, humidity, and temperature extremes. Do not place the product in any area

where it may be exposed to moisture.

• Place the product on a stable surface.

• If you encounter technical problems with the product, contact a qualied service

technician or your retailer.

About this guide

This user guide contains the information you need when installing and conguring the

motherboard.

How this guide is organized

This guide contains the following parts:

• Chapter 1: Product introduction

This chapter describes the features of the motherboard and the new technology it

supports. It includes descriptions of the switches, jumpers, and connectors on the

motherboard.

• Chapter 2: BIOS information

This chapter discusses changing system settings through the BIOS Setup menus.

Detailed descriptions for the BIOS parameters are also provided.

Where to nd more information

Refer to the following sources for additional information and for product and software

updates.

1. ASUS websites

The ASUS website provides updated information on ASUS hardware and software

products. Refer to the ASUS contact information.

2. Optional documentation

Your product package may include optional documentation, such as warranty yers,

that may have been added by your dealer. These documents are not part of the

standard package.

Conventions used in this guide

To ensure that you perform certain tasks properly, take note of the following symbols used

throughout this manual.

DANGER/WARNING: Information to prevent injury to yourself when

completing a task.

CAUTION: Information to prevent damage to the components when

completing a task

IMPORTANT: Instructions that you MUST follow to complete a task.

NOTE: Tips and additional information to help you complete a task.

Typography

Bold text Indicates a menu or an item to select.

Italics

Used to emphasize a word or a phrase.

<Key> Keys enclosed in the less-than and greater-than sign

means that you must press the enclosed key.

Example: <Enter> means that you must press the Enter or

Return key.

<Key1> + <Key2> + <Key3> If you must press two or more keys simultaneously, the key

names are linked with a plus sign (+).

PRIME B250M-A specications summary

(continued on the next page)

Package contents

Check your motherboard package for the following items.

Motherboard

ASUS PRIME B250M-A motherboard

Cables

2 x Serial ATA 6.0 Gb/s cables

Accessories

1 x I/O Shield

1 x M.2 screw package

Application DVD

1 x Support DVD

Documentation

1 x User Manual

If any of the above items is damaged or missing, contact your retailer.

CPU

LGA1151 socket for 7th / 6th Generation Intel

Core™ i7 / i5 / i3, Pentium

and Celeron

processors

Supports Intel

14nm CPU

Supports Intel

Turbo Boost Technology 2.0*

* The Intel

Turbo Boost Technology 2.0 support depends on the CPU types.

** Refer to www.asus.com for Intel

CPU support list.

Chipset Intel

B250 Chipset

Memory

4x DIMM, max 64 GB, DDR4 2400 / 2133 MHz, non-ECC, un-buffered memory*

Dual-channel memory architecture

Supports Intel

Extreme Memory Prole (XMP)

* DDR4 2400MHz memory frequency is only supported by 7th Generation Intel

processors.

** Hyper DIMM support is subject to the physical characteristics of individual CPUs. Please

refer to Memory QVL (Qualied Vendors List) for details.

Expansion

slots

1 x PCI Express 3.0/2.0 x16 slot (@ x16 mode)

2 x PCI Express 3.0/2.0 x1 slots

Graphics

Integrated graphics processor - Intel

HD Graphics support

Multi-VGA output support: HDMI, DVI-D, D-sub ports

- Supports HDMI 1.4b with maximum resolution of 4096 x 2160 @24Hz / 2560 x

1600 @60Hz

- Supports DVI-D with maximum resolution of 1920 x 1200 @60Hz

- Supports D-sub with maximum resolution of 1920 x 1200 @60Hz

Maximum shared memory of 1024MB

Storage

Intel

B250 Chipset

- 1 x M.2_1 Socket 3 with M key, type 2242/2260/2280 storage devices support (both

SATA & PCIE 3.0 x 4 mode)*

- 1 x M.2_2 Socket 3 with M key, type 2242/2260/2280 storage devices support (PCIE

3.0 x 4 mode)

- Ready for Intel

Optane Memory**

- 6 x SATA 6.0 Gb/s ports (gray)

- Supports Intel

Smart Response Technology***

* When M.2 Socket 3 is set to SATA mode, SATA port 1 is disabled.

** Intel

Optane Technology is only supported when using 7th Generation Intel

processors.

Before using Intel

Optane memory modules, ensure that you have updated your

motherboard drivers and BIOS to the latest version from ASUS support website.

***These functions will work depending on the CPU installed.

vii

PRIME B250M-A specications summary

(continued on the next page)

LAN

Realtek

8111H Gigabit LAN supports LANGuard

Audio

Realtek

ALC887 8-channel High Denition Audio CODEC

Gaming Audio:

- LED-illuminated design: Brighten up your build with the gorgeous illuminated

audio trace path

- Audio Shielding: Ensures precision analog/digital separation and greatly reduces

multi-lateral interference

- Dedicated audio PCB layers: Separate layers for left and right channels to guard

the quality of the sensitive audio signals

- Premium Japanese audio capacitors: Provide warm, natural and immersive

sound with exceptional clarity and delity

- Supports Jack-Detection and Front Panel Jack-Retasking

USB

Intel

B250 Chipset

- 1 x 5Gb/s USB Type C port supports 3A power output (at back panel)

- 4 x USB 3.0/2.0 ports (2 ports at mid-board; 2 ports at back panel, blue, Type

- 6 x USB 2.0/1.1 ports (4 ports at mid-board; 2 ports at back panel)

ASUS unique

features

ASUS 5X PROTECTION III

- ASUS SafeSlot Core - Strengthens your slot and DIMM pins

- ASUS LANGuard - Protects against LAN surges, lightning strikes

staticelectricity discharges!

ASUS Overvoltage Protection - World-class circuit-protecting power

design

- ASUS DIGI+ VRM - 5 Phase digital power design

- ASUS Stainless-Steel Back I/O: 3X corrosion-resistance for greater durability!

Superb Performance

M.2 Onboard

- The latest transfer technologies with up to 32Gb/s data transfer speeds

ASUS EPU

- EPU

UEFI BIOS

- Most advanced options with fast response time

Gaming Scenario

Audio Features

- Audio that roars on the battleeld

ASUS Exclusive Features

- ASUS AI Charger

- ASUS AI Suite 3

viii

PRIME B250M-A specications summary

ASUS unique

features

EZ DIY

UEFI BIOS EZ Mode

- Featuring friendly graphics user interface

- ASUS CrashFree BIOS 3

- ASUS EZ Flash 3

Q-Design

- ASUS Q-DIMM

- ASUS Q-Slot

ASUS Quiet

Thermal

Solution

Quiet Thermal Design

- ASUS Fan Xpert 2+

- Stylish Fanless Design: PCH Heatsink

Rear panel I/O

ports

1 x PS/2 keyboard port (purple)

1 x PS/2 mouse port (green)

1 x DVI-D port

1 x RGB port

1 x HDMI port

1 x 5Gb/s USB Type C port

2 x USB 2.0/1.1 ports

2 x USB 3.0/2.0 ports (blue, Type A)

1 x LAN (RJ-45) port

3 x Audio jacks support 8-channel audio output*

* Use a chassis with HD audio module in the front panel to support an 8-channel

audio output.

Internal

connectors

1 x USB 3.0 / 2.0 connector supports additional 2 USB 3.0/ 2.0 ports (19-pin)

2 x USB 2.0 / 1.1 connectors support additional 4 USB 2.0/ 1.1 ports

6 x SATA 6.0 Gb/s connectors (gray)

2 x M.2 Socket 3 (for M Key, type 2242/2260/2280 devices)

1 x CPU fan connector (PWM mode only)

2 x Chassis Fan connectors (4-pin) for both 3-pin (DC mode) and 4-pin (PWM

mode) coolers control

1 x Front panel audio connector (AAFP)

1 x Speaker connector

1 x COM connector

1 x Chassis Intrusion header

1 x System panel connector

1 x Clear CMOS header

1 x S/PDIF Out header

1 x TPM connector

1 x LPT connector

1 x 24-pin EATX power connector

1 x 4-pin ATX 12V power connector

BIOS features

128Mb Flash ROM, UEFI AMI BIOS, PnP, DMI3.0, WfM2.0, SM BIOS 3.0,

ACPI 6.1, Multi-language BIOS, ASUS EZ Flash 3, CrashFree BIOS 3, F6

Qfan Control, F3 My Favorites, Last Modied log, F12 PrintScreen, and ASUS

DRAM SPD (Serial Presence Detect) memory information

(continued on the next page)

Specications are subject to change without notice.

PRIME B250M-A specications summary

Manageability WfM 2.0, DMI 3.0, WOL/WOR by PME, PXE

Support DVD

Drivers

ASUS utilities

EZ Update

Anti-virus software (OEM version)

OS support

Windows

10 ( 64-bit)

Windows

8.1 (64-bit)*

Windows

7 (64-bit / 32-bit)*

* Windows

8.1 64-bit and Windows

7 32/64-bit are only supported when using 6th

Generation Intel

Processors.

Form factor mATX form factor: 9.6 in. x 8.1 in. (24.4 cm x 20.6 cm)

ASUS PRIME B250M-A

1-1

Product introduction

Motherboard overview

• Unplug the power cord from the wall socket before touching any component.

• Before handling components, use a grounded wrist strap or touch a safely grounded

object or a metal object, such as the power supply case, to avoid damaging them due

to static electricity.

• Before you install or remove any component, ensure that the ATX power supply is

switched off or the power cord is detached from the power supply. Failure to do so

may cause severe damage to the motherboard, peripherals, or components.

• Unplug the power cord before installing or removing the motherboard. Failure to do so

can cause you physical injury and damage to motherboard components.

Place this

side towards

the rear of the

chassis

Scan the QR code to get the detailed pin denitions.

PRIME B250M-A

PCIE SATA

M.2_2

IRST

X4 X V

PCIE SATA

M.2_1

IRST

X4 V X

PCIEX16

PCIEX1_1

PCIEX1_2

SPEAKER

CHASSIS

CLRTC

F_PANEL

TPM

SPDIF_OUT

USB1112USB910

LPT

USB3_12

AAFP

COM

ATX12V

EATXPWR

CHA_FAN2

CPU_FAN

CHA_FAN1

BATTERY

Super

I/O

ALC

887

Realtek

8111H

DIGI

+VRM

24.4cm(9.6in)

LGA1151

Intel

B250

DDR4 DIMM_A1 (64bit, 288-pin module)

2280 2260 2242

M.2_2(SOCKET3) M.2_1(SOCKET3)

DDR4 DIMM_A2 (64bit,288-pin module)

DDR4 DIMM_B1 (64bit, 288-pin module)

DDR4 DIMM_B2 (64bit, 288-pin module)

AUDIO

KBMS

HDMI

LAN_USB78

USB3_C3

USB3_56

20.6cm(8.1in)

128Mb

BIOS

SATA6G_5SATA6G_6 SATA6G_4

SATA6G_3 SATA6G_2 SATA6G_1

DVI

VGA

LANGuard

321 42

88 910

12131415

1-2

Chapter 1: Product introduction

ATX power connectors (24-pin EATXPWR, 4-pin ATX12V)

Correctly orient the ATX power supply plugs into these connectors and push down

rmly until the connectors completely t.

•

For a fully congured system, we recommend that you use a power supply unit

(PSU) that complies with ATX 12 V Specication 2.0 (or later version) and provides

a minimum power of 350 W.

•

If you are uncertain about the minimum power supply requirement for your system,

refer to the Recommended Power Supply Wattage Calculator at http://support.

asus.com/PowerSupplyCalculator/PSCalculator.aspx?SLanguage=en-us for

details.

CPU and chassis fan connectors (4-pin CPU_FAN, 4-pin CHA_FAN 1/2)

Connect the fan cables to the fan connectors on the motherboard, ensuring that the

black wire of each cable matches the ground pin of the connector.

Do not forget to connect the fan cables to the fan connectors. Insufcient air ow inside

the system may damage the motherboard components. These are not jumpers! Do not

place jumper caps on the fan connectors! The CPU_FAN connector supports a CPU fan

of maximum 1A (12 W) fan power.

Intel

LGA1151 CPU socket

Install Intel

LGA1151 CPU into this surface mount LGA1151 socket, which is designed

for 7th / 6th Generation Intel

Core™ i7 / i5 / i3, Pentium

, and Celeron

processors.

For more details, refer to Central Processing Unit (CPU).

DDR4 DIMM slots

Install 2 GB, 4 GB, 8 GB, and 16 GB unbuffered non-ECC DDR4 DIMMs into these

DIMM sockets.

For more details, refer to System memory.

System panel connector (10-1 pin F_PANEL)

This connector supports several chassis-mounted functions.

Speaker connector (4-pin SPEAKER)

This 4-pin connector is for the chassis-mounted system warning speaker. The

speaker allows you to hear system beeps and warnings.

ASUS PRIME B250M-A

1-3

CLRTC

+3V_BAT

GND

PIN 1

Clear RTC RAM (2-pin CLRTC)

This header allows you to clear the CMOS RTC RAM

data of the system setup information such as date,

time, and system passwords.

To erase the RTC RAM:

1. Turn OFF the computer and unplug the power

cord.

2. Use a metal object such as a screwdriver to

short the two pins.

3. Plug the power cord and turn ON the computer.

4. Hold down the <Del> key during the boot

process and enter BIOS setup to re-enter data.

If the steps above do not help, remove the onboard battery and short the two pins again

to clear the CMOS RTC RAM data. After clearing the CMOS, reinstall the battery.

Intel

B250 Serial ATA 6.0Gb/s connectors (7-pin SATA6G_1~6)

These connectors connect to Serial ATA 6.0 Gb/s hard disk drives via Serial ATA

6.0 Gb/s signal cables.

When using hot-plug and NCQ, set the SATA Mode Selection item in the BIOS to

[AHCI].

Chassis intrusion header (4-1 pin CHASSIS)

This header is for a chassis-mounted intrusion detection sensor or switch. Connect

one end of the chassis intrusion sensor or switch cable to this header. The chassis

intrusion sensor or switch sends a high-level signal to this header when a chassis

component is removed or replaced. The signal is then generated as a chassis

intrusion event.

By default, the pin labeled “Chassis Signal” and “Ground” are shorted with a

jumper cap. Remove the jumper caps only when you intend to use the chassis

intrusion detection feature.

USB 3.0 connector (20-1 pin USB3_12)

Connect a USB 3.0 module to this connector for additional USB 3.0 front or rear

panel ports. This connector complies with USB 3.0 specications and provides

faster data transfer speeds of up to 5 Gbps, faster charging time for USB-

chargeable devices, optimized power efciency, and backward compatibility with

USB 2.0.

USB 2.0 connectors (10-1 pin USB910, USB1112)

Connect the USB module cable to any of these connectors, then install the module

to a slot opening at the back of the system chassis. These USB connectors comply

with USB 2.0 specications and support up to 480Mbps connection speed.

1-4

Chapter 1: Product introduction

TPM connector (14-1 pin TPM)

This connector supports a Trusted Platform Module (TPM) system, which can

securely store keys, digital certicates, passwords and data. A TPM system also

helps enhance network security, protects digital identities, and ensures platform

integrity.

LPT connector (26-1 pin LPT)

The LPT (Line Printing Terminal) connector supports devices such as a printer.

LPT standardizes as IEEE 1284, which is the parallel port interface on IBM PC-

compatible computers.

Serial port connector (10-1 pin COM)

This connector is for a serial (COM) port. Connect the serial port module cable to

this connector, then install the module to a slot opening at the back of the system

chassis.

Digital audio connector (4-1 pin SPDIF_OUT)

Connect the S/PDIF Out module cable to this

connector, then install the module to a slot opening at

the back of the system chassis.

M.2 socket 3

These sockets allow you to install an M.2 (NGFF) SSD

module.

These sockets support M Key and

2242/2260/2280 storage devices.

Front panel audio connector (10-1 pin AAFP)

This connector is for a chassis-mounted front panel audio I/O module that supports

either HD Audio or legacy AC`97 audio standard. Connect one end of the front

panel audio I/O module cable to this connector.

• We recommend that you connect a high-denition front panel audio module to this

connector to avail of the motherboard’s high-denition audio capability.

• If you want to connect a high-denition front panel audio module to this connector,

set the Front Panel Type item in the BIOS setup to [HD Audio]. If you want to

connect an AC’97 front panel audio module to this connector, set the item to

[AC97]. By default, this connector is set to [HD Audio].

PCI Express 3.0/2.0 x1 slots

This motherboard supports PCI Express 3.0/2.0 x1 network cards, SCSI cards, and

other cards that comply with the PCI Express specications

PCI Express 3.0/2.0 x16 slot

This motherboard has a PCI Express 3.0/2.0 x16 slot that supports PCI Express

3.0/2.0 x16 graphic cards complying with the PCI Express specications.

SPDIF_OUT

+5V

SPDIFOUT

GND

PIN 1

M.2(SOCKET3)

ASUS PRIME B250M-A

1-5

IRQ assignments for this motherboard

A B C D

HD Audio shared – – –

XHCI Controller shared – – –

SATA Controller shared – – –

Realtek 8111H

LAN

– – – shared

PCIEx16 shared – – –

PCIEx1_1 shared – – –

PCIEx1_2 – shared – –

M.2_1 shared – – –

M.2_2 shared – – –

1-6

Chapter 1: Product introduction

1. PS/2 mouse port (green). This port is for a PS/2 mouse.

2. Video Graphics Adapter (VGA) port. This 15-pin port is for a VGA monitor or other

VGA-compatible devices.

3. LAN (RJ-45) port. This port allows Gigabit connection to a Local

Area Network (LAN) through a network hub.

Rear panel connectors

4 53

10 8 7

11 9

4. Line In port (light blue). This port connects to the tape, CD, DVD player, or other

audio sources.

5. Line Out port (lime). This port connects to a headphone or a speaker. In the 4.1, 5.1

and 7.1-channel congurations, the function of this port becomes Front Speaker Out.

6. Microphone port (pink). This port connects to a microphone.

Refer to the audio conguration table for the function of the audio ports in 2.1, 4.1, 5.1, or

7.1-channel conguration.

Activity/Link LED Speed LED

Status Description Status Description

Off No link OFF 10Mbps connection

Orange Linked ORANGE 100Mbps connection

Orange (Blinking) Data activity GREEN 1Gbps connection

Orange (Blinking

then steady)

Ready to wake up

from S5 mode

_ _

LAN port

Speed

LED

Activity Link

LED

LAN port LED indications

ASUS PRIME B250M-A

1-7

Audio 2.1, 4.1, 5.1, or 7.1-channel conguration

Port

Headset

2.1-channel

4.1-channel 5.1-channel 7.1-channel

Light Blue (Rear panel) Line In Rear Speaker Out Rear Speaker Out Rear Speaker Out

Lime (Rear panel) Line Out Front Speaker Out Front Speaker Out Front Speaker Out

Pink (Rear panel) Mic In Mic In Bass/Center Bass/Center

Lime (Front panel) - - - Side Speaker Out

To congure a 7.1-channel audio output:

Use a chassis with HD audio module in the front panel to support a 7.1-channel audio

output.

7. USB 2.0 ports. These 4-pin Universal Serial Bus (USB) ports are for USB 2.0/1.1

devices.

8. USB 3.0 ports. These 9-pin Universal Serial Bus (USB) ports are for USB 3.0/2.0

devices.

• USB 3.0 devices can only be used for data storage.

• We strongly recommend that you connect USB 3.0 devices to USB 3.0 ports for faster

and better performance from your USB 3.0 devices.

• Due to the design of the Intel

100 series chipset, all USB devices connected to the

USB 2.0 and USB 3.0 ports are controlled by the xHCI controller. Some legacy USB

devices must update their rmware for better compatibility.

9. HDMI port. This port is for a High-Denition Multimedia Interface (HDMI) connector,

and is HDCP compliant allowing playback of HD DVD, Blu-Ray, and other protected

content.

10. USB 5Gb/s Type C port. This 24-pin Universal Serial Bus (USB) port is for USB (Type

C) devices.

11. DVI-D port. This port is for any DVI-D compatible device.

DVI-D cannot be converted to output from RGB Signal to CRT and is not compatible with

DVI-I.

12. PS/2 keyboard port (purple). This port is for a PS/2 keyboard.

1-8

Chapter 1: Product introduction

Central Processing Unit (CPU)

This motherboard comes with a surface mount LGA1151 socket

designed for 7th / 6th Generation Intel

Core™ i7 / i5 / i3, Pentium

, and

Celeron

processors.

• Ensure that you install the correct CPU designed for the LGA1151 socket only. DO

NOT install a CPU designed for LGA1150, LGA1155 and LGA1156 sockets on the

LGA1151 socket.

• Upon purchase of the motherboard, ensure that the PnP cap is on the socket and

the socket contacts are not bent. Contact your retailer immediately if the PnP cap

is missing, or if you see any damage to the PnP cap/socket contacts/motherboard

components.

• Keep the cap after installing the motherboard. ASUS will process Return Merchandise

Authorization (RMA) requests only if the motherboard comes with the cap on the

LGA1151 socket.

• The product warranty does not cover damage to the socket contacts resulting from

incorrect CPU installation/removal, or misplacement/loss/incorrect removal of the PnP

cap.

Installing the CPU

Unplug all power cables before installing the CPU.

Apply the Thermal Interface Material to the CPU heatsink and CPU before you install the

heatsink and fan if necessary.

ASUS PRIME B250M-A

1-9

System memory

Overview

This motherboard comes with four Double Data Rate 4 (DDR4) Dual Inline Memory Module

(DIMM) sockets. The gure illustrates the location of the DDR4 DIMM sockets:

Channel Sockets

Channel A DIMM_A1 & DIMM_A2

Channel B DIMM_B1 & DIMM_B2

• You may install varying memory sizes in Channel A and Channel B. The system

maps the total size of the lower-sized channel for the dual-channel conguration. Any

excess memory from the higher-sized channel is then mapped for single-channel

operation.

• Always install the DIMMS with the same CAS Latency. For an optimum compatibility,

we recommend that you install memory modules of the same version or data code

(D/C) from the same vendor. Check with the vendor to get the correct memory

modules.

• According to Intel

CPU spec, DIMM voltage below 1.35V is recommended to protect

the CPU.

• Due to the memory address limitation on 32-bit Windows

OS, when you install 4GB

or more memory on the motherboard, the actual usable memory for the OS can be

about 3GB or less. For effective use of memory, we recommend that you do any of the

following:

- Use a maximum of 3 GB system memory if you are using a 32-bit Windows

OS.

- Install a 64-bit Windows

OS if you want to install 4GB or more on the

motherboard.

- For more details, refer to the Microsoft

support site at http://support.microsoft.

com/kb/929605/en-us.

• Visit the ASUS website at www.asus.com for the latest QVL.

DIMM_A1

DIMM_A2

DIMM_B1

DIMM_B2

1-10

Chapter 1: Product introduction

Installing a DIMM

1 2

To remove a DIMM

BIOS information

• Scan the QR code to view the BIOS update guide.

• Before using the ASUS CrashFree BIOS 3 utility, rename the

BIOS le in the removable device into B250MA.CAP.

BIOS setup program

Use the BIOS Setup program to update the BIOS or congure its parameters. The BIOS

screens include navigation keys and brief online help to guide you in using the BIOS Setup

program.

Entering BIOS Setup at startup

To enter BIOS Setup at startup:

Press <Delete> or <F2> during the Power-On Self Test (POST). If you do not press <Delete>

or <F2>, POST continues with its routines.

Entering BIOS Setup after POST

To enter BIOS Setup after POST:

• Press <Ctrl>+<Alt>+<Del> simultaneously.

• Press the reset button on the system chassis.

• Press the power button to turn the system off then back on. Do this option only if you

failed to enter BIOS Setup using the rst two options.

Using the power button, reset button, or the <Ctrl>+<Alt>+<Del> keys to force reset from a

running operating system can cause damage to your data or system. We recommend you

always shut down the system properly from the operating system.

• The BIOS setup screens shown in this section are for reference purposes only, and

may not exactly match what you see on your screen.

• Visit the ASUS website at www.asus.com to download the latest BIOS le for this

motherboard.

• If the system becomes unstable after changing any BIOS setting, load the default

settings to ensure system compatibility and stability. Select the Load Optimized

Defaults item under the Exit menu or press hotkey F5.

• If the system fails to boot after changing any BIOS setting, try to clear the CMOS and

reset the motherboard to the default value. See section Motherboard overview for

information on how to erase the RTC RAM.

BIOS menu screen

The BIOS setup program can be used under two modes: EZ Mode and Advanced Mode.

Press <F7> to change between the two modes.

ASUS PRIME B250M-A

2-1

La pagina sta caricando ...

Asus PRIME B250M-A Manuale utente

Marca: Asus

Modello: PRIME B250M-A

Categoria: Schede madri

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: Asus PRIME B250M-A User manual
română: Asus PRIME B250M-A Manual de utilizare

Asus PRIME B250M-A Manuale utente

Asus PRIME B250M-A Manuale utente

in altre lingue

Documenti correlati

Altri documenti