Biostar MCP6PB M2+ Manuale del proprietario

MCP6PB M2+ Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. There is no guarantee

that interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the

contents here and specially disclaims any implied warranties of merchantability

or fitness for any purpose. Further the vendor reserves the right to revise this

publication and to make changes to the contents here without obligation to

notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without first

obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and

we will not be responsible for any mistakes found in this user’s manual. All the

brand and product names are trademarks of their respective companies.

Table of Contents

Chapter 1: Introduction ........................................ 1

1.1 Before You Start ................................................................................ 1

1.2 Package Checklist............................................................................. 1

1.3 Motherboard Features...................................................................... 2

1.4 Rear Panel Connectors ..................................................................... 3

1.5 Motherboard Layout......................................................................... 4

Chapter 2: Hardware Installation .......................... 5

2.1 Installing Central Processing Unit (CPU)....................................... 5

2.2 FAN Headers...................................................................................... 7

2.3 Installing System Memory................................................................ 8

2.4 Connectors and Slots....................................................................... 10

Chapter 3: Headers & Jumpers Setup .................. 12

3.1 How to Setup Jumpers .................................................................... 12

3.2 Detail Settings.................................................................................. 12

Chapter 4: RAID Functions .................................. 19

4.1 Operating System............................................................................ 19

4.2 Raid Arrays ...................................................................................... 19

4.3 How RAID Works............................................................................. 19

Chapter 5: Useful Help ........................................ 21

5.1 Driver Installation Note.................................................................. 21

5.2 Software............................................................................................ 22

5.3 Award BIOS Beep Code .................................................................. 23

5.4 Extra Information............................................................................ 23

5.5 Troubleshooting............................................................................... 24

Appendix: SPEC In Other Languages ................... 26

German.................................................................................................................. 26

French .................................................................................................................... 28

Italian..................................................................................................................... 30

Spanish ................................................................................................................... 32

Portuguese ............................................................................................................ 34

Polish...................................................................................................................... 36

Russian ................................................................................................................... 38

Arabic..................................................................................................................... 40

Japanese ................................................................................................................ 42

MCP6PB M2+

1

CHAPTER 1: INTRODUCTION

1.1 B

EFORE YOU START

Thank you for choosing our product. Before you start installing the

motherboard, please make sure you follow the instructions below:

 Prepare a dry and stable working environment with

sufficient lighting.

 Always disconnect the computer from power outlet

before operation.

 Before you take the motherboard out from anti-static

bag, ground yourself properly by touching any safely

grounded appliance, or use grounded wrist strap to

remove the static charge.

 Avoid touching the components on motherboard or the

rear side of the board unless necessary. Hold the board

on the edge, do not try to bend or flex the board.

 Do not leave any unfastened small parts inside the

case after installation. Loose parts will cause short

circuits which may damage the equipment.

 Keep the computer from dangerous area, such as heat

source, humid air and water.

1.2 PACKAGE CHECKLIST

IDE Cable X 1

Serial ATA Cable X 1

Rear I/O Panel for ATX Case X 1

Installation Guide X 1

Fully Setup Driver CD X 1 (full version manual files inside)

FDD Cable X 1 (optional)

USB 2.0 Cable X1 (optional)

Serial ATA Power Cable X 1 (optional)

Note: The package contents may be differed by area or your motherboard version.

Motherboard Manual

2

1.3 MOTHERBOARD FEATURES

SPEC

CPU

Socket AM2 / AM2+

AMD Athlon 64 / Athlon 64 FX

/

Athlon 64 x2

/ Sempron / PhenomX3 / X4 processors

(Maximum Watt: 95W)

AMD 64 Architecture enables 32 and 64 bit

comput ing

Supports Hyper Transport and PowerNow

FSB

Support HyperTransport 1.0 Ghz

Supports up to 2 GT/s Bandwidth

Chipset GeForce 6150SE

Super I/O

ITE 8718F

Provides the most commonly used legacy

Super I/O functionality

Low Pin Count Interface

Env ironment Control in it iatives

H/W Monitor

ITE's "Smart Guard ian" funct ion

Main

Memory

DDR2 DIMM Slots x 2

Max Memory Capacity 4GB

Each DIMM supports 256MB/512MB/

1GB/2GB DDR2

Dual Channel Mode DDR2 memory module

Supports DDR2 533 / 667 / 800

Supports DDR2 1066 (by AM2+ CPU)

Registered DIMM and ECC DIMM is not supported

Graphics Integrated in GeForce 6150SE Chipset Max Shared Video Memory is 256MB

IDE Integrated IDE Contro lle r

Ultra DMA 33 / 66 / 100 / 133 Bus Master Mode

supports PIO Mode 0~4,

SATA II Integrated Serial ATA Controller

Data transfer rates up to 3 Gb/s

SATA Version 2.0 specificat ion co mp liant

LAN Realtek RTL 8201CL PHY

10 / 100 Mb/s auto negotiation

Half / Full duplex capability

Sound ALC662

5.1 channels audio out

High Definition Audio

PCI Express x16 slot x1 Supports PCI-E x16 expansion cards

Slots

PCI slot x1 Supports PCI expansion cards

Floppy connector x1 Each connector supports 2 Floppy drives

IDE Connector x1 Each connector supports 2 IDE device

SATA Connector x2 Each connector supports 1 SATA devices

Front Panel Connector x1 Supports front panel facilities

On Board

Connector

Front Audio Connector x1 Supports front panel audio function

MCP6PB M2+

3

SPEC

CPU Fan header x1 CPU Fan power supply (with Smart Fan function)

System Fan head er x1 System Fan Power supply

CMOS clear header x1 Restore CMOS data to factory default

USB connector x2 Each connector supports 2 front panel USB ports

Power Connector (24pin) x1 Connects to Power supply

Power Connector (4pin) x1 Connects to Power supply

Printer Port Connector x1 Each connector supports 1 Printer port

Serial port Connector x1 Connects to RS-232 Port

Back Panel

I/O

PS/2 Keyboard x1

PS/2 Mouse x1

VGA port x1

LAN port x1

USB Port x4

Audio Jack x3

Connects to PS/2 Keyboard

Connects to PS/2 Mouse

Connect to D-SUB monitor

Connect to RJ-45 ethernet cable

Connect to USB devices

Provide Audio-In/Out and microphone connection

Board Size 170 mm(W) x 235 mm(L) MicroATX

Special

Features

RAID 0 / 1

OS Support Windows XP / Vista / 7

Biostar Reserves the right to add or remove support

for any OS With or without notice.

1.4 R

EAR PANEL CONNECTORS

PS/2

Mouse

PS/ 2

Keyboard

USBX2USBX2

LAN

VGA

Line In/

Surround

Line Out

Mic In 1/

Bass/ Center

Motherboard Manual

4

1.5 MOTHERBOARD LAYOUT

JKBMS

JKB_PWR

JATXPWR2

JVGA

JUSB1

JUSBLAN1

JAUDIO1

JUSBPWR1

JCFAN

BAT1

LAN

JAUDIOF

Codec

PCI1

JPRNT

SATA2 SATA1

JSFAN

J PANE L1

FDD

BI OS

Super I/O

JCMOS1

JUSB2

JU S B3

JUSBPWR2

IDE

JATXPWR1

DIMMB1

DIMMA1

Socket AM2+

PEX16_1

JCO M

GeForce

6150SE

Note: represents the 1■

st

pin.

MCP6PB M2+

5

CHAPTER 2: HARDWARE INSTALLATION

2.1 I

NSTALLING CENTRAL PROCESSING UNIT (CPU)

Step 1: Remove the socket protection cap.

Step 2: Pull the lever toward direction A from the socket and then raise the

lever up to a 90-degree angle.

Step 3: Look for the white triangle on socket, and the gold triangle on

CPU should point towards this white triangle. The CPU will fit only

in the correct orientation.

Motherboard Manual

6

Step 4: Hold the CPU down firmly, and then close the lever toward direct

B to complete the installation.

Step 5: Put the CPU Fan on the CPU and buckle it. Connect the CPU

FAN power cable to the JCFAN. This completes the installation.

Note: Please update the BIOS to the latest version while using AM2+ CPUs. Due to the latest CPU

transition, you may encounter the situation that the new system failed to boot while using new

AM2+ CPUs. In this case, please install one standard AM2 CPU to boot your system, and

update the latest BIOS from our website for AM2+ CPUs support.

MCP6PB M2+

7

2.2 FAN HEADERS

These fan headers support cooling-fans built in the computer. The fan

cable and connector may be different according to the fan manufacturer.

Connect the fan cable to the connector while matching the black wire to

pin#1.

JCFAN: CPU Fan Header

Assignment

1 Ground

2 +12V

3

FAN RPM rate

sense

1

4

4 Smart Fan

Control (By Fan)

JSFAN: System Fan Header

Assignment

1 Ground

2 +12V

13

3 FAN RPM rate

sense

Note:

The JCFAN supports 4-pin head connector; the JSFAN, 3-pin head connector. When

connecting with wires onto connectors, please note that the red wire is the positive and

should be connected to pin#2, and the black wire is Ground and should be connected to

GND.

Motherboard Manual

8

2.3 INSTALLING SYSTEM MEMORY

A. Memory Modules

DIMMA1

DIMMB1

1. Unlock a DIMM slot by pressing the retaining clips outward. Align a

DIMM on the slot so that the notch on the DIMM matches the break

on the Slot.

2. Insert the DIMM vertically and firmly into the slot until the retaining

chip snap back in place and the DIMM is properly seated.

MCP6PB M2+

9

B. Memory Capacity

DIMM Socket

Location

DDR2 Module

Total Mem ory

Size

DIMMA1 256MB/512MB/1GB/2GB

DIMMB1 256MB/512MB/1GB/2GB

Max is 4GB.

C. Dual Channel Memory installation

To trigger the Dual Channel function of the motherboard, the memory module

must meet the following requirements:

Install memory module of the same density in pairs, shown in the following

table.

Dual Channel Status DIMMA1 DIMMB1

Disabled O X

Disabled X O

Enabled O O

(O means memory installed, X means memory not installed.)

The DRAM bus width of the memory module must be the same (x8 or

x16)

Motherboard Manual

10

2.4 CONNECTORS AND SLOTS

FDD: Floppy Disk Connector

The motherboard provides a standard floppy disk connector that supports 360K,

720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the

provided floppy drive ribbon cable.

133

234

IDE: IDE/ATAPI Connector

The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO

Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality.

The IDE connector can connect a master and a slave drive, so you can connect

up to two drives.

21

3940

MCP6PB M2+

11

PEX16_1: PCI-Express Gen2 x16 Slot

- PCI-Express 1.0a compliant.

- Maximum theoretical realized bandwidth of 4GB/s simultaneously per

direction, for an aggregate of 8GB/s totally.

- PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.

- 2X bandwidth over the traditional PCI architecture.

PEX16_1

PCI1: Peripheral Component Interconnect Slot

This motherboard is equipped with 1 standard PCI slot. PCI stands for

Peripheral Component Interconnect, and it is a bus standard for expansion

cards. This PCI slot is designated as 32 bits.

PCI1

Motherboard Manual

12

CHAPTER 3: HEADERS & JUMPERS SETUP

3.1 H

OW TO SETUP JUMPERS

The illustration shows how to set up jumpers. When the jumper cap is

placed on pins, the jumper is “close”, if not, that means the jumper is

“open”.

Pin opened Pin closed Pin1-2 closed

3.2 DETAIL SETTINGS

JPANEL1: Front Panel Header

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, Sleep,

and speaker connection. It allows user to connect the PC case’s front panel

switch functions.

1

8

16

PWR _LE D

On/Off

RST

HLED

SPK

++

+

9

-

Pin Assignment Function Pin Assignment Function

1 +5V 9 N/A

2 N/A 10 N/A

N/A

3 N/A 11 N/A N/A

4 Speaker

Speaker

Connector

12 Power LED (+)

5 HDD LED (+) 13 Power LED (+)

6 HDD LED (-)

Hard drive

LED

14 Power LED (-)

Power LED

7 Ground 15 Power button

8 Reset control

Reset button

16 Ground

Power-on button

MCP6PB M2+

13

JATXPWR1: ATX Power Source Connector

This connector allows user to connect 24-pin power connector on the ATX

power supply.

24

13

12

1

Pin Assignment Pin Assignment

13 +3.3V 1 +3.3V

14 -12V 2 +3.3V

15 Ground 3 Ground

16 PS_ON 4 +5V

17 Ground 5 Ground

18 Ground 6 +5V

19 Ground 7 Ground

20 NC 8 PW_OK

21 +5V 9 Standby Voltage+5V

22 +5V 10 +12V

23 +5V 11 +12V

24 Ground 12 +3.3V

JATXPWR2: ATX Power Source Connector

By connecting this connector, it will provide +12V to CPU power circuit.

Assignment

1 +12V

2 +12V

3 Ground

2

34

1

4 Ground

Note:

Before power on the system, please make sure that both JATXPWR1 and JATXPWR2

connectors have been plugged-in.

Motherboard Manual

14

JUSB2/JUSB3: Headers for USB 2.0 Ports at Front Panel

These headers allow user to connect additional USB cable on the PC front panel,

and also can be connected with internal USB devices, like USB card reader.

Assignment

1 +5V (fused)

2 +5V (fused)

3 USB-

4 USB-

5 USB+

6 USB+

7 Ground

8 Ground

9 NC

21

10 9

JUSB2 JUSB3

10 Key

SATA1/SATA2: Serial ATA Connectors

The motherboard has a PCI to SATA Controller with 2 channels SATA interface,

it satisfies the SATA 2.0 spec and with transfer rate of 3.0Gb/s.

Assignment

1 Ground

2 TX+

3 TX-

4 Ground

5 RX-

6 RX+

14 7

SATA2 SATA1

7 Ground

MCP6PB M2+

15

JAUDIOF: Front Panel Audio Header

This header allows user to connect the front audio output cable with the PC front

panel. This header allows only HD audio front panel connector; AC’97 connector

is not acceptable.

Assignment

1 Mic Left in

2 Ground

3 Mic Right in

4 GPIO

5 Right line in

6 Jack Sense

7 Front Sense

8 Key

9 Left line in

19

210

10 Jack Sense

JCOM: Serial port Connector

The motherboard has a Serial Port Connector for connecting RS-232 Port.

Assignment

1 Carrier detect

2 Received data

3 Transmitted data

4 Data terminal ready

5 Signal ground

6 Data set ready

7 Request to send

8 Clear to send

9 Ring indicator

19

210

10 NC

Motherboard Manual

16

JCMOS1: Clear CMOS Header

By placing the jumper on pin2-3, it allows user to restore the BIOS safe setting

and the CMOS data, please carefully follow the procedures to avoid damaging

the motherboard.

31

Pin 1-2 Close:

Normal Operation (default).

31

Pin 2-3 Close:

Clear CMOS data.

※ Clear CMOS Procedures:

1. Remove AC power line.

2. Set the jumper to “Pin 2-3 close”.

3. Wait for five seconds.

4. Set the jumper to “Pin 1-2 close”.

5. Power on the AC.

6. Reset your desired password or clear the CMOS data.

MCP6PB M2+

17

JPRNT: Printer Port Connector

This header allows you to connect printer port on the PC.

125

2

Pin Assignment Pin Assignment

1 -Strobe 14 Ground

2 -ALF 15 Data 6

3 Data 0 16 Ground

4 -Error 17 Data 7

5 Data 1 18 Ground

6 -Init 19 -ACK

7 Data 2 20 Ground

8 -Scltin 21 Busy

9 Data 3 22 Ground

10 Ground 23 PE

11 Data 4 24 Ground

12 Ground 25 SCLT

13 Data 5 26 Key

Motherboard Manual

18

JUSBPWR1/JUSBPWR2: Power Source Headers for USB Ports

Pin 1-2 Close:

JUSBPWR1: +5V for USB ports at JUSB1/JUSBLAN1.

JUSBPWR2: +5V for USB ports at front panel (JUSB2/JUSB3).

Pin 2-3 Close:

JUSBPWR1: +5V STB for USB ports at JUSB1/JUSBLAN1.

JUSBPWR2: +5V STB for USB ports at front panel (JUSB2/JUSB3).

1

3

Pin 1-2 close

1

3

JUSBPWR1

1

3

JUSBPWR2

1

3

Pin 2-3 close

JKB_PWR: Power Source Header for PS/2 Keyboard and Mouse

31

Pin 1-2 close

+5V for PS/2 keyboard and

mouse.

31

Pin 2-3 close

+5V STB for PS/2 keyboard

and mouse.

La pagina sta caricando ...

Biostar MCP6PB M2+ Manuale del proprietario

Biostar MCP6PB M2+ Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti