Fusion Fusion Apollo RA770 Guida d'installazione

Marca: Fusion

Modello: Fusion Apollo RA770

Tipo: Guida d'installazione

Questo manuale è adatto anche per

Apollo

™

RA770 Installation

Instructions

Important Safety Information

WARNING

Failure to follow these warnings and cautions could result in

personal injury, damage to the vessel, or poor product

performance.

See the Important Safety and Product Information guide in the

product box for product warnings and other important

information.

This device must be installed according to these instructions.

Disconnect the vessel's power supply before beginning to install

this product.

Before applying power to this product, make sure it has been

correctly grounded, following the instructions in the guide.

CAUTION

Always wear safety goggles, ear protection, and a dust mask

when drilling, cutting, or sanding.

NOTICE

When drilling or cutting, always check what is on the opposite

side of the surface.

You must read all installation instructions before beginning the

installation. If you experience difficulty during the installation,

contact FUSION

Product Support.

What's In the Box

• Mounting gasket

• Four 8-gauge, self-tapping screws

• Two screw covers

• Power and speaker wiring harness

• Auxiliary-in, line-out, and subwoofer-out wiring harnesses

• 2 m (6 ft.) NMEA 2000

drop cable

• Dust cover

Tools Needed

• Phillips screwdriver

• Electric drill

• Drill bit (size varies based on surface material and screws

used)

• Rotary cutting tool or jigsaw

• Silicone-based marine sealant (optional)

Mounting Considerations

• The stereo must be mounted on a flat surface.

• The stereo must be mounted in a location that allows open

airflow around the rear of the stereo for heat ventilation.

• If you are installing the stereo in a location that may be

exposed to water, it must be mounted within 45 degrees

below or 15 degrees above the horizontal plane.

•

If you are installing the stereo in a location that may be

exposed to water, you should install any connected cables

with a drip loop to allow water to drip down off the cable and

avoid damage to the stereo.

• If you need to mount the stereo outside a boat, it must be

mounted in a location far above the waterline, where it is not

submerged.

• If you need to mount the stereo outside a boat, it should be

mounted in a location where it cannot be damaged by docks,

pilings, or other pieces of equipment.

• To avoid interference with a magnetic compass, the stereo

should be installed at least 15 cm (5.9 in.) away from a

compass.

Mounting the Stereo

NOTICE

Be careful when cutting the hole to mount the stereo. There is

only a small amount of clearance between the case and the

mounting holes, and cutting the hole too large could

compromise the stability of the stereo after it is mounted.

Be careful when installing the stereo in an aluminum boat or a

boat with a conductive hull, if you require the electrical system to

be isolated from the boat hull.

Do not apply grease or lubricant to the screws when fastening

the stereo to the mounting surface. Grease or other lubricants

can cause damage to the stereo housing.

Before you can mount the stereo in a new location on the

mounting surface, you must select a location in accordance with

the mounting considerations.

Trim the template and make sure it fits at the mounting

location.

Adhere the template to the mounting surface.

Using a drill bit appropriate for the mounting surface, drill a

hole inside the corner of the dashed line on the template to

prepare the mounting surface for cutting.

Using a rotary-cutting tool, cut the mounting surface along

the inside of the dashed line on the template.

Place the stereo in the cutout

to test the fit.

August 2018

190-02382-02_0B

If necessary, use a file and sandpaper to refine the size of

the cutout.

After the stereo fits correctly in the cutout, ensure the

mounting holes on the stereo line up with the pilot holes on

the template.

If the mounting holes on the stereo do not line up, mark the

new pilot-hole locations.

Using an appropriately sized drill bit for the mounting surface

and screw type, drill the pilot holes.

Remove the template from the mounting surface.

Make the necessary wiring connections (Connection

Considerations, page 2).

Select an option:

• If you are installing the stereo in a dry location, place the

included mounting gasket

on the back of the stereo.

• If you are installing the stereo in a location that is exposed

to water, apply silicone-based marine sealant on the

mounting surface around the cutout.

NOTICE

Do not install the included mounting gasket if you applied

sealant to the mounting surface. Using sealant and the

mounting gasket may reduce water resistance.

Place the stereo into the cutout.

Secure the stereo to the mounting surface using the included

screws

You should hand-tighten the screws when securing the

stereo to the mounting surface to avoid overtightening them.

Snap the screw covers in place

Connection Considerations

For the stereo to function correctly, you must connect it to

power, to speakers, and to input sources. You should carefully

plan the layout of the stereo, speakers, input sources, optional

NMEA 2000 network, and optional FUSION PartyBus

™

devices

or network before making any connections.

Port Identification

Item Description

ANTENNA Connects the stereo to a typical AM/FM antenna.

If you are installing the stereo on a boat with a metal

hull, you must use a ground-dependent antenna. If you

are installing the stereo on a boat with a non-metal

hull, you must use a ground-independent antenna.

See the installation instructions provided with your

antenna for more information.

NMEA 2000 Connects the stereo to a NMEA 2000 network (NMEA

2000 System Wiring Diagram, page 4).

Connects to an NRX series remote control directly

(Configuring an Optional Wired Remote, page 4).

ETHERNET Connects the stereo to another FUSION PartyBus

stereo, zone stereo, or network (FUSION PartyBus

Networking, page 4).

SIRIUS XM Connects the stereo to a SiriusXM

Connect Tuner to

receive SiriusXM stations where available (not

included).

Connects to a FUSION DAB module to receive DAB

stations where available (not included).

USB Connects the stereo to a USB source.

DIGITAL

AUDIO IN

Connects the stereo to an optical digital audio source,

such as TV or DVD player.

FUSE Contains the 15 A fuse for the device.

Connects the stereo to the wiring harness for auxiliary

input 2, and for the line and subwoofer outputs for

zones 3 and 4.

Connects the stereo to the wiring harness for auxiliary

input 1, and for the line and subwoofer outputs for

zones 1 and 2.

Connects the stereo to the power and speaker wiring

harness.

Wiring Harness Wire and Connector Identification

Wire or RCA

Connector

Function

Bare Wire

Color or

RCA Label

Name

Notes

Ground (-) Black Connects to the negative terminal of

a 12 Vdc power source capable of

supplying 15 A. You should connect

this wire before connecting the

yellow wire. All accessories

connected to the stereo must share

a common ground location

(Connecting to Power, page 3).

Power (+) Yellow Connects to the positive terminal of a

12 Vdc power source capable of

supplying 15 A.

Ignition Red Connects to a separately-switched,

12 Vdc connection, such as an

ignition bus, to turn the stereo on

and off. If you are not using a

switched 12 Vdc connection, you

must connect this to the same

source as the yellow (power) wire

2 Apollo RA770 Installation Instructions

Wire or RCA

Connector

Function

Bare Wire

Color or

RCA Label

Name

Notes

Amplifier on Blue Connects to optional external

amplifiers, enabling them to turn on

when the stereo turns on.

Telemute Brown Activates when connected to ground.

For example, when you connect this

wire to a compatible, hands-free

mobile kit, the audio mutes or the

input switches to Aux1 when a call is

received and the kit connects this

wire to ground. You can enable this

functionality from the settings menu.

Dim Orange Connects to the boat's illumination

wire to dim the stereo screen when

the lights are on.

The gauge of the illumination wire

must be suitable for the fuse

supplying the circuit it is connected

to.

Speaker zone 1

left (+)

White

Speaker zone 1

left (-)

White/black

Speaker zone 1

right (+)

Gray

Speaker zone 1

right (-)

Gray/black

Speaker zone 2

left (+)

Green

Speaker zone 2

left (-)

Green/

black

Speaker zone 2

right (+)

Purple

Speaker zone 2

right (-)

Purple/

black

Zone 1 line out

(left)

Zone 1 line out

(right)

Zone 1 subwoofer

out

ZONE 1

SUB OUT

Provides output to an external

amplifier, and is associated with the

volume control for zone 1.

Each subwoofer cable provides a

single mono output to a powered

subwoofer or subwoofer amplifier.

Zone 2 line out

(left)

Zone 2 line out

(right)

Zone 2 subwoofer

out

ZONE 2

SUB OUT

Provides output to an external

amplifier, and is associated with the

volume control for zone 2.

Each subwoofer cable provides a

single mono output to a powered

subwoofer or subwoofer amplifier.

Auxiliary in 1 left

Auxiliary in 1 right

AUX IN 1 Provides an RCA stereo line input for

audio sources, such as a CD or MP3

player.

Zone 3 line out

(left )

Zone 3 line out

(right)

Zone 3 subwoofer

out

ZONE 3

SUB OUT

Provides output to an external

amplifier, and is associated with the

volume control for zone 3.

Each subwoofer cable provides a

single mono output to a powered

subwoofer or subwoofer amplifier.

Zone 4 line out

(left)

Zone 4 line out

(right)

Zone 4 subwoofer

out

ZONE 4

SUB OUT

Provides output to an external

amplifier, and is associated with the

volume control for zone 4.

Each subwoofer cable provides a

single mono output to a powered

subwoofer or subwoofer amplifier.

Auxiliary in 2 left

Auxiliary in 2 right

AUX IN 2 Provides and RCA stereo line input

for audio sources, such as a CD or

MP3 player.

Connecting to Power

When connecting the stereo to power, you must connect both

power wires. You should connect the yellow power wire directly

to the battery. This provides power to the stereo and a constant

trickle-power standby feed.

You should connect the red signal wire to the same battery

through the ignition or another manual switch to turn the stereo

on and off. If you are not routing the red wire through the ignition

or another manual switch, you can connect the red wire to the

yellow wire, and connect them both to the positive (+) battery

terminal.

You must connect the power wires to the battery through a 15 A

fuse or a 15 A circuit breaker.

If it is necessary to extend the yellow power and black ground

wires, use 14 AWG (2.08 mm

) wire. For extensions longer than

1 m (3 ft.), use 12 AWG (3.31 mm²) wire. If it is necessary to

extend the red wire, use 22 AWG (0.33 mm

) wire.

Route the yellow power

, red signal

, and black ground

wires to the battery, and route the wiring-harness plug to the

stereo.

Do not connect the wiring harness to the stereo until all of the

bare wire connections have been made.

Connect the black wire to the negative (-) battery terminal.

If you are routing the red wire through the ignition or another

manual switch

, connect the red signal wire to the ignition

or switch.

Connect the red wire to the yellow wire, install a 15 A fuse

as close to the battery as possible, and connect both wires to

the positive (+) battery terminal.

NOTE: If you are running the red wire through a fused switch,

it is not necessary to connect the red wire to the yellow wire

or to add an another fuse to the red wire.

Speaker Zones

You can group speakers in one area into a speaker zone. This

enables you to control the audio level of the zones individually.

For example, you could make the audio quieter in the cabin and

louder on deck.

Up to two pairs of speakers can be connected per channel of

each zone, in parallel. A zone can support no more than four

speakers using the on-board amplifier.

Zones 1 and 2 are powered by the on-board amplifier. To use

the RCA line outputs and the RCA subwoofer outputs for zones

1 and 2, you must connect external amplifiers.

Zones 3 and 4 are available as line-level outputs only. To use

the RCA line outputs and the RCA subwoofer outputs for zones

3 and 4, you must connect external amplifiers.

You can set the balance, volume limit, tone, subwoofer level,

subwoofer frequency, and name for each zone, and configure

other zone-specific settings.

Apollo RA770 Installation Instructions 3

Single-Zone System Wiring Example

Speakers

Water-tight connection

Extended System Wiring

This diagram illustrates a system installation with an external

amplifier and subwoofer connected to zone 2 on the stereo. You

can connect an amplifier and subwoofer to any or all of the four

zones on the stereo.

Item Description

Zone 1 speakers

Water-tight connection

Zone 2 speakers

Amplifier-on signal wire

You must connect this wire to each amplifier connected to a zone

line out.

Powered amplifier connected to the zone 2 line out

Zone 2 line out and subwoofer out

Each subwoofer cable provides a single mono output to a

powered subwoofer or subwoofer amplifier.

Subwoofer

NMEA 2000 System Wiring Diagram

Stereo

Supported chartplotter MFD or compatible FUSION NMEA 2000

remote control

In-line switch

NMEA 2000 power cable

NMEA 2000 drop cable from the stereo, up to 6 m (20 ft.)

NMEA 2000 drop cable from the chartplotter MFD or compatible

FUSION NMEA 2000 remote control

9 to 16 Vdc power supply

NMEA 2000 terminator or backbone cable

NMEA 2000 T-connector

NMEA 2000 terminator or backbone cable

Configuring an Optional Wired Remote

NOTICE

The stereo is configured by default to work with a NMEA 2000

network, and the NRX POWER option should be enabled only

when an optional remote is connected directly to the stereo.

Enabling this option when the stereo is connected to a NMEA

2000 network may damage other devices on the NMEA 2000

network.

If you connect an optional wired NRX remote directly to the

stereo, and not through a NMEA 2000 network , additional

configuration is needed.

Select > > NMEA.

Select an option:

• If you connected both your stereo and your optional wired

remote to a NMEA 2000 network, make sure the NRX

POWER option is not selected. This enables the optional

remote to receive power from the NMEA 2000 network.

• If you connected the optional wired remote directly to the

stereo through the NMEA 2000 connector, select the NRX

POWER option. This enables the stereo to supply power

to the optional remote.

FUSION PartyBus Networking

The FUSION PartyBus networking feature allows you to connect

multiple compatible stereos and zone stereos together on a

network, using a combination of wired or wireless connections.

A FUSION PartyBus stereo, such as an Apollo RA770 stereo,

can stream sources to other FUSION PartyBus devices

connected to the network. Connected FUSION PartyBus

devices can also control media playback on the FUSION

PartyBus stereo. A FUSION PartyBus zone stereo, such as an

Apollo SRX400 zone stereo can stream from a FUSION

4 Apollo RA770 Installation Instructions

PartyBus stereo, but cannot stream sources to other FUSION

PartyBus devices on the network.

You can connect up to eight FUSION PartyBus devices on a

network.

In the image above, one Apollo RA770 stereo

connects to a

wireless router

and to two Apollo SRX400 zone stereos

The two FUSION PartyBus stereo zone stereos can stream

sources from the FUSION PartyBus stereo.

A FUSION PartyBus zone stereo is not the same thing as a

speaker zone. It is an independent stereo that can either play

media from connected sources or stream from a FUSION

PartyBus stereo on the network. You can connect a FUSION

PartyBus zone stereo, such as an Apollo SRX400 zone stereo,

to a single speaker zone

. You can connect a FUSION

PartyBus stereo, such as an Apollo RA770 stereo, to multiple

speaker zones

to cover a larger area with that stereo.

FUSION PartyBus devices cannot control the speaker volume of

another stereo. You can adjust the volume of speakers or

speaker zones connected directly to the stereo only.

Wired Networking Considerations

When you are planning your network installation, observe the

following considerations for all wired connections.

• Wired connections are more reliable than wireless

connections. When planning your network, you should use

network cables to connect FUSION PartyBus devices to the

network when possible.

• You must connect devices using standard Cat5e or Cat6

network cables with RJ45 connectors.

• You can use one network cable to directly connect two

compatible devices.

• You may need to use wired network switches and wired or

wireless network routers when you connect more than two

compatible stereos to a network.

• If you install a router on the network, it should be configured

to be the DHCP server by default. See your router

instructions for more information.

• If you do not install a router on the network, you must

configure one FUSION PartyBus device to be the DHCP

server.

Wired Network Example for Direct Connections

You must configure one FUSION PartyBus device as a DHCP

server when connecting two devices together directly.

FUSION PartyBus stereo

FUSION PartyBus zone stereo

Wired Network Example with a Switch or Router

You must use wired network switches, a wired network router, or

both to connect more than two FUSION PartyBus devices.

FUSION PartyBus stereo

Wired network switch or wired network router

FUSION PartyBus zone stereo

Wireless Networking Considerations

When you are planning your network, observe the following

considerations for all wireless connections.

• Wired connections are more reliable than wireless

connections. You should plan your network to use network

cables, but if it is not possible, FUSION PartyBus devices are

Wi‑Fi

compatible. You can connect them to wireless routers

or access points.

• You can configure a FUSION PartyBus device as a wireless

access point, so you can connect devices within wireless

range.

• If you install a wireless router on the network, it should be

configured to be the DHCP server by default. See your

wireless router instructions for more information.

• If you do not install a router or wireless router on the network,

you must configure one FUSION PartyBus device to be the

DHCP server.

• You can configure any FUSION PartyBus device on the wired

network to be a wireless access point, even if you install a

wireless router or additional wireless access points on the

network. This would be useful to allow access to devices in

range of the stereo but not in range of the other wireless

access points.

• If you connect a FUSION PartyBus device to the network

wirelessly, you cannot connect any additional wired FUSION

PartyBus devices to that device.

• You can connect a smartphone to the wireless network to

control any stereo on the network using the FUSION-Link

™

app.

• You can connect an Apple

device to the wireless network to

stream media to a single stereo on the network using Apple

AirPlay

Wireless Access Point Example

Apollo RA770 Installation Instructions 5

FUSION PartyBus stereo

FUSION PartyBus zone stereo

Smartphone using the FUSION-Link app

Wireless Network Example with a Wired Switch or Router

FUSION PartyBus stereo

Wired network switch or wired network router

FUSION PartyBus zone stereo

Smartphone using the FUSION-Link app.

Wireless Network Example with a Wireless Router or

Access Point

FUSION PartyBus stereo

Wireless network router or wireless access point

FUSION PartyBus zone stereo

Smartphone using the FUSION-Link app

Constructing a Network

You should have a basic understanding of networking when

building a network for FUSION PartyBus devices.

These instructions guide you through the basics of building and

configuring a network, and should apply to most situations. If

you need to perform advanced networking tasks, such as

assigning static IP addresses to devices on the network or

configuring advanced settings on a connected router, you may

need to consult a networking professional.

Determine the installation location of the FUSION PartyBus

devices you want to connect to the network.

NOTE: Wired connections are more reliable than wireless

connections. When planning your network, you should run

network cables instead of using wireless connections when

possible.

Determine the installation location of any needed network

routers or switches.

Route Cat5e or Cat6 network cable to the installation

locations of the stereos, switches, and router.

Connect the network cables to the stereos, switches, and

router.

NOTICE

Do not completely install the stereos yet. You should test the

network before you install the stereos.

Turn on all devices connected to the network, including

wireless devices.

Select an option:

• If you are not using a network router (wired or wireless),

configure one FUSION PartyBus device to be the DHCP

server (Setting the FUSION PartyBus Device as the

DHCP Server, page 6). All other stereos should use

their default configuration (automatic IP).

• If you are using a network router (wired or wireless),

consult the documentation provided with your router to

configure the router as the DHCP server, if necessary. All

stereos should use their default configuration (automatic

IP).

Configure a stereo as a wireless access point, if necessary

(Setting the FUSION PartyBus Device as a Wireless Access

Point, page 6).

Configure a FUSION PartyBus stereo or zone stereo to

connect to a wireless access point or router, if necessary

(Connecting the FUSION PartyBus Device to a Wireless

Access Point, page 6).

Test the network by viewing the list of FUSION PartyBus

devices from each device on the network and select an

option:

• If any FUSION PartyBus devices are not available to the

network, troubleshoot the network (Network

Troubleshooting, page 7).

• If all FUSION PartyBus devices are available to the

network, complete the installation for each stereo, if

necessary.

Network Configuration

TIP: You can select the network status icon from any screen to

open the network configuration menu.

Setting the FUSION PartyBus Device as the DHCP Server

If you connected two FUSION PartyBus devices together

directly, or connected more than two together using a network

switch and did not install a router, you must configure only one

FUSION PartyBus stereo to be the DHCP server.

Select > > NETWORK > ADVANCED > DHCP

SERVER > DHCP ENABLED > SAVE.

Setting the FUSION PartyBus Device as a Wireless Access

Point

Before you can connect additional FUSION PartyBus devices or

smartphones to a FUSION PartyBus device wirelessly, you must

configure at least one device as a wireless access point. This is

not necessary if you installed a wireless router or other wireless

access point on the network.

Select > > NETWORK > WI-FI ACCESS POINT.

Select SSID, and enter the SSID, or name, for the wireless

access point.

Select AP SECURITY, and select the security type for the

access point (optional).

NOTE: It is strongly recommended that you set the AP

SECURITY using WPA2 PERSONAL. It is the most widely-

used and secure wireless security protocol.

Select PASSWORD, and enter a password for the access

point (optional).

If necessary, select COUNTRY, and select your region.

Select SAVE.

Connecting the FUSION PartyBus Device to a Wireless

Access Point

Select > > NETWORK > WI-FI CLIENT > SSID.

A list of wireless access points within rage appears.

Select the FUSION PartyBus wireless access point.

6 Apollo RA770 Installation Instructions

Select an option:

• To enter the password, select PASSWORD, enter the

password, and select .

• If you are connecting to the wireless access point using

WPS, verify that WPS has been enabled on the access

point, and select WPS.

NOTE: It can take up to two minutes to successfully

connect to the access point after you select WPS.

Select SAVE.

Resetting Network Settings

You can reset all network settings for this stereo to the factory

default values.

Select > > NETWORK > RESET > YES.

Advanced Network Configuration

You can perform advanced networking tasks on a FUSION

PartyBus device, such as defining DHCP ranges and setting

static IP addresses. See the owner's manual for more

information.

Network Troubleshooting

If you cannot see or connect to FUSION PartyBus devices on

the network, check the following:

• Verify that only one device, either a stereo or a router, is

configured as a DHCP server.

• Verify that all FUSION PartyBus devices, network switches,

routers, and wireless access points are connected to the

network and turned on.

• Verify that wireless FUSION PartyBus devices are connected

to a wireless router or wireless access point on the network.

• If you configured static IP addresses, verify that every device

has a unique IP address, that the first three sets of numbers

in the IP addresses match, and that the subnet masks on

every device are identical.

• If you have made configuration changes that might be

causing networking issues, reset all network settings to

factory defaults.

Stereo Information

Specifications

General

Weight 750 g (26.5 oz.)

Water resistance IEC 60529 IPX7 (front of stereo only,

when properly installed)

Operating temperature range From 0 to 50°C (from 32 to 122°F)

Storage temperature range From -20 to 70°C (from -4 to 158°F)

Input voltage From 10.8 to 16 Vdc

Current (max.) 15 A

Current (muted) Less than 900 mA

Current (off, standby mode

enabled)

110 mA

Current (off, standby mode

disabled)

80 mA

Fuse 15 A mini blade-type

NMEA 2000 LEN 1 (50 mA)

Bluetooth

wireless range Up to 10 m (30 ft.)

ANT

wireless range Up to 3 m (10 ft.)

Wireless frequencies/protocols Wi‑Fi 2.4 GHz @ +15 dBm nominal

Bluetooth 2.4 GHz @ +10 dBm

nominal

ANT 2.4 GHz @ +4 dBm nominal

Compass-safe distance 15 cm (5.9 in.)

On-board, Class D Amplifier

Output music power per

channel

4 x 70 W max. 2 ohm

Total output peak power 280 W max.

Output power per channel 4 x 43 W RMS at 14.4 Vdc input,

2 ohm, 10% THD*

4 x 26 W RMS at 14.4 Vdc input,

4 ohm, 10% THD*

Line output level (max.) 5.5 V (peak to peak)

Aux input level (typical) 1 V RMS

*The stereo may limit the output power to prevent the amplifier

from overheating, and to maintain the audio dynamics.

Tuner Europe and

Australasia

USA Japan

FM radio

frequency range

87.5 to 108 MHz 87.5 to

107.9 MHz

76 to 95 MHz

FM frequency

step

50 kHz 200 kHz 50 kHz

AM radio

frequency range

522 to 1620 kHz 530 to

1710 kHz

522 to

1620 kHz

AM frequency

step

9 kHz 10 kHz 9 kHz

Stereo Dimension Drawings

Front Dimensions

192 mm (7.56 in.)

82 mm (3.23 in.)

Side Dimensions

20.4 mm (0.8 in.)

99 mm (3.9 in.)

50 mm (1.97 in.)

Apollo RA770 Installation Instructions 7

Top Dimensions

164 mm (6.5 in.)

20.4 mm (0.8 in.)

10 mm (0.39 in.)

Registering Your Apollo RA770

Help us better support you by completing our online registration

today.

• Go to www.fusionentertainment.com.

• Keep the original sales receipt, or a photocopy, in a safe

place.

Software Updates

For best results, you should update the software in all FUSION

devices at the time of installation to ensure compatibility.

You can update the software using the FUSION-Link remote

control app on your compatible Apple or Android

™

device, or

using a USB flash drive.

To download the app and update the device software, go to the

Apple App Store

or the Google Play

™

store. For software

updates and instructions on updating the device using the USB

flash drive, go to the device product page at

www.fusionentertainment.com/marine.

Garmin

, ANT

, FUSION

, and the Fusion logo are trademarks of Garmin Ltd. or its

subsidiaries, registered in the USA and other countries.

Apollo

™

, FUSION-Link

™

, and

FUSION PartyBus

™

are trademarks of Garmin Ltd. or its subsidiaries. These trademarks

may not be used without the express permission of Garmin.

Apple

,AirPlay

, iPhone

, and iPod touch

are trademarks of Apple Inc., registered in the

USA and other countries. App Store

is a service mark of Apple Inc., registered in the

USA and other countries.

Android

™

and Google Play

™

are a trademarks of Google Inc.

Bluetooth

word mark and logos are owned by the Bluetooth SIG, Inc. and any use of

such marks by Garmin is under license.

NMEA 2000

, and the NMEA 2000 logo are

registered trademarks of the National Marine Electronics Association. SiriusXM

is a

registered trademark of SiriusXM Radio Inc.

Wi‑Fi

is a registered mark of Wi-Fi Alliance

Corporation. Other trademarks and trade names are those of their respective owners.

www.fusionentertainment.com

Fusion Fusion Apollo RA770 Guida d'installazione

Marca: Fusion

Modello: Fusion Apollo RA770

Tipo: Guida d'installazione

Questo manuale è adatto anche per

Scarica il pdf

rapporto

in altre lingue

English: Fusion Fusion Apollo RA770 Installation guide

Fusion Fusion Apollo RA770 Guida d'installazione

Questo manuale è adatto anche per

Fusion Fusion Apollo RA770 Guida d'installazione

in altre lingue

Documenti correlati

Altri documenti