EPOX EP-MVP4A2 Manuale utente

TRADEMARK

All products and company names are trademarks or

registered trademarks of their respective holders.

These specifications are subject to change without notice.

Manual Revision 1.0

August 9, 1999

EP-MVP4FEP-MVP4F

EP-MVP4F

ISAISA

ISA

/PCI Mainboard with Onboard AGP/PCI Mainboard with Onboard AGP

/PCI Mainboard with Onboard AGP

VGA, PCI Audio, PCI IDE and SuperVGA, PCI Audio, PCI IDE and Super

VGA, PCI Audio, PCI IDE and Super

Multi-I/OMulti-I/O

Multi-I/O

EP-MVP4F

User Notice

No part of this product, including the product and software may be reproduced,

transmitted, transcribed, stored in a retrieval system, or translated into any

language in any form without the express written permission of EPoX Computer

Company (hereinafter referred to as EPoX) except for documentation kept by the

purchaser for backup purposes.

We provide this manual “as is” without warranty of any kind, either expressed or

implied, including but not limited to the implied warranties or conditions of

merchantability or fitness for a particular purpose. In no event shall EPoX be

liable for any loss of profits, loss of business, loss of use or data, interruption of

business or for indirect, special incidental, or consequential damages of any kind,

even if EPoX has been advised of the possibility of such damages arising from any

defect or error in the manual or product. EPoX may revise this manual from time

to time without notice. For updated BIOS, drivers, or product release information

you may visit our websites at http://www.epox.com or http://www.epox.com.tw.

Products mentioned in this manual are mentioned for identification purposes only.

Product names appearing in this manual may or may not be registered trademarks

or copyrights of their respective companies. The product name and revision

number are both printed on the mainboard itself.

Handling Procedures

Static electricity can severely damage your equipment. Handle the EP-MVP4F and

any other device in your system with extreme care and avoid unnecessary contact

with system components on the mainboard. Always work on an antistatic surface

to avoid possible damage to the mainboard from static discharge. Always have the

power supply unplugged and powered off when inserting and removing devices

within the computer chassis. EPoX assumes no responsibility for any damage to

the EP-MVP4F mainboard that results from failure to follow instruction or failure

to observe safety precautions.

CAUTION

The EP-MVP4F mainboard is subject to

damage by static electricity. Always

observe the handling procedures.

EP-MVP4F

Technical Support Services

If you need additional information, help during installation or normal use of this

product, please contact your retailer. Your retailer will have the most current

information about your configuration. If your retailer cannot help, you may visit

our online technical support website and/or contact our support technicians at the

locations listed below.

Record your serial number before installing your EP-MVP4F mainboard. (The

serial number is located near the PCI slots at the edge of the board.)

EP-MVP4F serial number: _________________________________

Contacting Technical Support

EPoX technical support is working hard to answer all of your questions online.

From our website you can find answers to many common questions, drivers, BIOS

updates, tech notes, and important technical bulletins. If you are still unable to

locate the solution you are seeking, you always have the option to contact our

support technicians directly.

North American website (English language)

http://www.epox.com

[email protected]

European website (Multi-language)

http://www.epox.nl

[email protected]

Taiwan website (Chinese language)

http://www.epox.com.tw

[email protected]

Thank you for using EPoX mainboards!

EP-MVP4F

Table of Contents

Section 1 Introduction

Components Checklist ............................................... 1-1

Overview

EP-MVP4F Form-factor ............................................ 1-2

I/O Shield Connector ................................................. 1-3

Power-On/Off (Remote)............................................ 1-3

System Block Diagram...............................................1-4

Section 2 Features

EP-MVP4F Features ..................................................2-1

Section 3 Installation

EP-MVP4F Detailed Layout ...................................... 3-1

Easy Installation Procedure

Configure DIP Switch ................................................ 3-3

System Memory Configuration ................................. 3-5

Device Connectors ..................................................... 3-7

Section 4 Award BIOS Setup

BIOS Instructions ....................................................... 4-1

Standard CMOS Setup ................................................4-2

BIOS Features Setup .................................................. 4-3

Chipset Features Setup...............................................4-8

Power Management Setup.......................................... 4-11

PNP/PCI Configuration ............................................. 4-14

Load Setup Defaults ................................................... 4-16

Integrated Peripherals ................................................ 4-16

Sensor and CPU Speed Setup..................................... 4-21

Change Supervisor or User Password .......................4-23

IDE HDD Auto Detection .......................................... 4-24

EP-MVP4F

Save & Exit Setup ....................................................... 4-26

Exit Without Saving .................................................... 4-26

Section 5 Appendix

Appendix A

Memory Map ..............................................................A-1

I/O Map ....................................................................... A-1

Timer & DMA Channels Map .................................... A-2

Interrupt Map .............................................................. A-2

RTC & CMOS RAM Map ........................................... A-3

Appendix B

POST Codes................................................................ A-5

Unexpected Errors ..................................................... A-8

Appendix C

Load Setup Defaults ................................................... A-9

Appendix D

GHOST 5.1 Quick User’s Guide................................A-11

EP-MVP4F

Page Left Blank

IntroductionEP-MVP4F

Page 1-1

Section 1

INTRODUCTION

Components Checklist

üü

ü A. (1) One mainboard

üü

ü B. (1) One user’s manual

üü

ü C. (1) Floppy ribbon cable

üü

ü D. (1) ATA-66 IDE ribbon cable

üü

ü E. (1) COM Port Connector

üü

ü F. (1) Driver and utility

USER’S

MANUAL

EP-MVP4F

B

A

C

D

F

or

E

Introduction EP-MVP4F

Page 1-2

EP-MVP4F Form Factor

The EP-MVP4F is designed with MicroATX form factor - the new industry

standard of chassis. The MicroATX form factor is essentially a Baby-AT base-

board rotated 90 degrees within the chassis enclosure and a new mounting

configuration for the power supply. With these changes the processor is relocated

away from the expansion slots, allowing them all to hold full length add-in cards.

MicroATX defines a double height aperture to the rear of the chassis which can be

used to host a wide range of onboard I/O. Only the size and position of this

aperture is defined, allowing PC manufacturers to add new I/O features (e.g.; TV

input, TV output, joystick, modem, LAN, etc.) to systems. This will help systems

integrators differentiate their products in the marketplace, and better meet your

needs.

• Smaller size promotes a smaller system size.

• I/O shield does not need to be retooled in an ATX 2.01 or later. Mainboard

could be used in an ATX 2.01-compliant.

• A smaller power supply cam be used. High integration on mainboard reduces

the system costs.

Full length

slots

Expandable I/O

5 1/4"

Bay

3 1/2"

Bay

Figure 2: Summary of Micro ATX chassis features

CPU located near

Power Supply

Single chassis

fan for

system

Micro

ATX

Power

Supply

ATX power

connector

Floppy / IDE

connectors

close to

peripheral

bays

IntroductionEP-MVP4F

Page 1-3

Case (chassis) Power

ON/OFF button

ATX

POWER SUPPLY

Figure 4: Simple ATX Power

ON/OFF Controller

Power-On/Off (Remote)

The EP-MVP4F has a single 20-pin connector for ATX power supplies. For ATX

power supplies that support the Remote On/Off feature, this should be connected

to the systems front panel for system Power On/Off button. The systems power

On/Off button should be a momentary button that is normally open.

The EP-MVP4F has been designed with “Soft Off" functions. You can turn Off

the system from one of two sources: The first is the front panel Power On/Off

button, and the other is the "Soft Off" function (coming from the EP-MVP4F’s

onboard circuit controller) that can be controlled by the operating system.

Windows 95/98 will control this when the user clicks that they are ready to

Shutdown the system.

I/O Shield Connector

The EP-MVP4F is equipped with an I/O back panel.Please use the appropriate I/O

shield (figure 3).

J3

PS/2 Mouse

PS/2

KEYBOARD

COM1 VGA1

parallel port

Speaker

Joystick/Midi

USB port

Line_in

MIC

Figure 3

Introduction EP-MVP4F

Page 1-4

Figure 5: System Block Diagram

System Block Diagram

PAC

PCI Bridge

and memory

controller

VT82C501

socket 7

Processor

100/66 MHz

CRT

VT82C686A

I/O Bridge

USB 0 USB 1

AC97

CODEC

~

AMR Slot

FeaturesEP-MVP4F

Page 2-1

Section 2

FEATURES

EP-MVP4F Features:

• Intel Pentium

®

Processor, Pentium Processor with MMX technology,

AMD K6/K6-2/K6 III, Cyrix 6x86MX/MII, IDT C6/Winchip, and Rise mp6

series operating at 133 ~ 500MHz with 321 ZIF socket 7 provides

scalability to accept faster Processors in the future.

• Designed with VIA MVP4 AGPset.

• Supports up to 256 MB of DRAM (minimum of 8 MB) on board,

You can use 168-pin DIMM x 2. (please see Section 3-2).

• Supports (2) 32 bit PCI slots, (1) AMR Slot and provides (2) independent

high performance PCI IDE interfaces capable of supporting PIO Mode 3/4

and Ultra DMA 33/66 devices. The EP-MVP4F supports (2) PCI Bus Master

slots and a jumperless PCI INT# control scheme which reduces configura-

tion confusion when plugging in PCI card(s).

• Supports ATAPI (e.g. CD-ROM) devices on both Primary and Secondary

IDE interfaces.

• Designed with lntegrated Multi I/O: (1) floppy port, (1) parallel port

(EPP, ECP), and (2) serial ports (16550 Fast UART).

Note: Japanese “Floppy 3 mode” is also supported

• Features Award Plug & Play BIOS. With Flash Memory you can always

upgrade to the current BIOS as they are released. (http://www.epox.com

please visit our Technical Support section for the latest updates)

• EP-MVP4F utilizes a Lithium battery which provides environmental

protection and longer battery life.

• Software power-down when using Windows

®

95/98.

Features EP-MVP4F

Page 2-2

• Supports ring-in feature (remote power-on through external modem,

allows system to be turned on remotely).

• Resume by Alarm - Allows your system to turn on at a preselected time.

• Supports CPU Hardware sleep and SMM (System Management Mode).

• Supports USDM software to offer motherboard various status.

• Built-in WOL (Wake On Lan) Connector.

• Built-in Sound Blaster Compatible/DirectSound AC97 Audio.

• Built-in AGP 2D/3D Graphics Accelerator.

InstallationEP-MVP4F

Page 3-1

Section 3

INSTALLATION

Installation EP-MVP4F

Page 3-2

Figure 1

EP-MVP4F Detailed Layout

InstallationEP-MVP4F

Page 3-3

Easy Installation Procedure

The following must be completed before powering on your new system:

3-1. Configure Jumpers

3-2. System Memory Configuration

3-3. Device Connectors

Section 3-1

Configure Jumpers

We design this motherboard with the fastest jumpers to make your install fast and

easy.

Note: The jumpers as depicted as shown (Figure 1) in their correct physical orientation.

1WS

suB

kcolC

1234

NOzHM66

NOzHM57

NONOzHM38

NONOzHM09

NONOzHM59

NONONOzHM001

NONONOzHM501

NONONOzHM511

1WS

UPC

reilpitluM

6CTDI/xiryC/DMA

UPC

reilpitluM

2pihCniWTDI

567

NOX2

NONOX5.2

NOX3

X5.3

NONOX4

NONONOX5.4

NONOX533.2

NOX5.566.2

JP2: CPU Vcore Voltage Selection

SW1: CPU Speed Selection

2PJerocVUPC

7-1V0.2

8-2V2.2

9-3V4.2

01-4V8.2

11-5V9.2

21-6V2.3

SW1

17

2.0V

2.2V

2.4V

2.8V

2.9V

3.2V

JP2

Installation EP-MVP4F

Page 3-4

* Reserved

CPU Type SW1

CPU

Bus

Clock

CPU

Multiplier

Pentium/MMX

AMD K6/K6-2/K6III

IDT-C6

Cyrix /IBM

6x86MX/MII

IDT Winchip 2 Rise MP6

1234567

166MHz PR200 ON ON ON 66MHz

2.5X

PR233 ON ON ON 75MHz

PR266 233MHz ON ON ON ON 83MHz

PR300 *PR333 ON ON ON ON 95MHz

250MHz PR366 300MHz *PR366 ON ON ON ON ON 100MHz

200MHz PR266 200MHz ON ON 66MHz

3X

PR300 225MHz ON ON 75MHz

250MHz PR333 266Mhz ON ON ON 83MHz

PR400 *PR380 ON ON ON 95MHz

300MHz *PR433 *PR400 ON ON ON ON 100MHz

233MHz PR300 233MHz ON 66MHz

3.5X

PR333 ON 75MHz

*PR400 ON ON 83MHz

333MHz *PR466 *PR433 ON ON 95MHz

350MHz *PR500 *PR466 ON ON ON 100MHz

266MHz *PR333 266MHz ON ON ON 66MHz

4X

*PR400 ON ON ON 75MHz

333MHz *PR466 ON ON ON ON 83MHz

380MHz *PR533 ON ON ON ON 95MHz

400MHz *PR550 ON ON ON ON ON 100MHz

300MHz ON ON ON ON 66MHz

4.5X

450MHz ON ON ON ON ON ON 100MHz

333MHz ON ON ON 66MHz

5X475MHz ON ON ON ON 95MHz

*500MHz 266MHz ON ON ON ON ON 100MHz

366MHz ON ON 66MHz

5.5X

*550MHz 300MHz ON ON ON ON 100MHz

J7

WOL (Wakup On Lan) Connector

Reserved for NIC (Network Interface Card) to

Wake the System.

InstallationEP-MVP4F

Page 3-5

Section 3-2

System Memory Configuration

Memory Layout

The EP-MVP4F supports (2) 168-pin DIMMs (Dual In-line Memory Module).

The DIMMs can be either EDO (Extended Data Out) or SDRAM (Synchronized

DRAM). The DIMMs may be installed using just one chip.

• DIMM SDRAM may be 83MHz (12ns), 100MHz (10ns) or

125MHz (8ns) bus speed.

• If you use both 50ns and 60ns memory you must configure

your BIOS to read 60ns.

• When using Synchronous DRAM we recommend using the

4 clock variety over the 2 clock.

Figure 2 and Table 1 show several possible memory configurations using

yromeMlatoT

1MMID

)1/0knaB(

2MMID

)3/2knaB(

BM821=

mumixaM

*MARDS/ODE

,BM46,BM23,BM61,BM8

1XBM821

enoN

BM652=

mumixaM

*MARDS/ODE

,BM46,BM23,BM61,BM8

1XBM821

*MARDS/ODE

,BM46,BM23,BM61,BM8

1XBM821

DIMM 1

DIMM 2

Bank 0/1

Bank 2/3

-Synchronous

-EDO

Figure 2

* SDRAM only supports 8, 16, 32, 64, 128MB DIMM modules.

* We recommend to use PC100 Memory Module for bus speed between

66MHz and 100MHz.

Table 1

Installation EP-MVP4F

Page 3-6

DIMM Module Installation

Figure 3 displays the notch marks and what they should look like on your DIMM

memory module.

DIMMs have 168-pins and two notches that will match with the onboard DIMM

socket. DIMM modules are installed by placing the chip firmly into the socket at

a 90 degree angle and pressing straight down (figure 4) until it fits tightly into the

DIMM socket (figure 5).

Figure 3

Figure 5

DIMM Module clip after installation

To remove the DIMM module simply press down both of the white clips on

either side and the module will be released from the socket.

Figure 4

DIMM Module clip before installation

CENTER KEY ZONE

(3.3 V DRAM)

LEFT KEY ZONE

(UNBUFFERED)

InstallationEP-MVP4F

Page 3-7

Section 3-3

Device Connectors

Please install the motherboard into the chassis.

PS/2 Mouse

PS/2

KEYBOARD

COM1 VGA1

parallel port

Speaker

Joystick/Midi

USB port

Line_in

MIC

Figure 6

J2: Chassis Panel Connector

• Power LED, Speaker, Reset

J3: Power_ON/OFF, Turbo LED, HDD LED, IR Connector

J4: CPU Fan Power

• A plug-in for the CPU Fan Power

J6: Chassis Fan Power

• A plug-in for the chassis Fan Power

J7: WOL (Wake On Lan) Connector

IDE1: Primary IDE Connector

IDE2: Secondary IDE Connector

FDD1: Floppy Controller Connector

PW1: ATX Power Connector

• 20-pin power connector

CD1: CD-ROM Audio_in Connector

MODEM1: Telephony Connector

• Pin1(Audio_in), Pin2/Pin3(GND), Pin4(Mic-out to Modem)

Installation EP-MVP4F

Page 3-8

Device Connectors (continued)

J2

Speaker - Connect to the system's speaker for beeping

1. Speaker 3. GND

2. N/C 4. GND

Reset - Closed to restart system.

Power LED - Power LED connector

1. Power LED(+) 4. NC

2. N/C 5. GND

3. GND

1

(This is connected to the power button on the case. Using the

Soft-Off by Pwr-BTTN feature, you can choose either Instant

Off (turns system off immediatly), or 4 sec delay (you need to

hold the button down for 4 seconds before the system turns off).

When the system is in 4 sec delay mode, there is a special feature

to make the system to go into suspend mode when the button is

pressed momentarily.)

Turbo LED indicator - LED ON when higher speed is selected

IDE LED indicator - LED ON when Onboard PCI IDE Hard

disks is activate

J3

1

+

IR Connector

1. VCC 4. GND

2. NC 5. IRTX

3. IRRX

1

Power On/Off

La pagina sta caricando ...

EPOX EP-MVP4A2 Manuale utente

Questo manuale è adatto anche per

EPOX EP-MVP4A2 Manuale utente

in altre lingue

Documenti correlati

Altri documenti