Ohaus SKX8200 Manuale utente

Scout

TM

Series Balances - SKX

Instruction Manual

Balanzas Scout

TM

- SKX Series

Manual de Instrucciones

Balances Scout

TM

Séries - SKX

Mode d’emploi

Bilance Serie Scout

TM

- SKX

Manuale d’Istruzioni

Scout

TM

Waagen-Serien – SKX

Bedienungsanleitung

SCOUT

TM

SERIES BALANCES - SKX EN-1

1. INTRODUCTION

This manual contains installation, operation and maintenance instructions for the Scout SKX

Series Balances. Please read the manual completely before using the balance.

1.1 Definition of Signal Warnings and Symbols

Safety notes are marked with signal words and warning symbols. These show safety issues and

warnings. Ignoring the safety notes may lead to personal injury, damage to the instrument,

malfunctions and false results.

Signal Words

WARNING For a hazardous situation with medium risk, possibly resulting in injuries or

death if not avoided.

CAUTION For a hazardous situation with low risk, resulting in damage to the device or

the property or in loss of data, or injuries if not avoided.

Attention For important information about the product.

Note For useful information about the product.

Warning Symbols

General Hazard Electric Shock Hazard

1.2 Safety Precautions

CAUTION: Read all safety warnings before installing, making connections, or

servicing this equipment. Failure to comply with these warnings could result in

personal injury and/or property damage. Retain all instructions for future

reference.

 Verify that the local AC power supply is within the input voltage range printed on the AC

adapter’s data label.

 Only connect the AC adapter to a compatible grounded electrical outlet.

 Do not position the scale such that it is difficult to disconnect the AC adapter from the

power receptacle.

 Make sure that the power cord does not pose a potential obstacle or tripping hazard.

 This equipment is intended for indoor use and should only be operated in dry locations.

 Operate the equipment only under ambient conditions specified in the user instructions.

 Do not operate the equipment in hazardous or unstable environments.

 Do not drop loads on the pan.

 Only use approved accessories and peripherals.

 Disconnect power from the equipment before cleaning or servicing.

 Service should only be performed by authorized personnel.

2. INSTALLATION

2.1 Installing Components

Refer to the illustrations and instructions below to identify and assemble your Scout balance

with its components. All components must be assembled before using the balance.

EN-2 SCOUT

TM

SERIES BALANCES - SKX

2.1.1 Releasing the Shipping Lock

Release the red Transportation Lock on

the sub-platform of the balance by

turning the red pointer 90 counter-

clockwise.

Figure 2-1. Transportation Lock

2.1.2 Installing the Weighing Pan

Balances with a rectangular pan are placed into the sub-platform as shown and rotated counter-

clockwise until it locks. Round pans are placed straight down on sub-platform.

Figure 2-2. Pan Installation

2.2.3 Security Slot

A security slot is provided at the rear of the balance allowing the balance to be secured by an

optional cable and lock accessory.

2.3 Selecting the Location

For best performance, the Scout SKX balance should be used in a clean, stable environment.

Do not use the balance in environments with excessive drafts, with rapid temperature changes,

near magnetic fields or near equipment that generates magnetic fields, or vibrations.

Sub-platform

Transportation

Lock Pointer

Locked Position

Unlocked

Position

SCOUT

TM

SERIES BALANCES - SKX EN-3

2.4 Connecting Power

AC Adapter Installation

AC power is used to power the scale when battery power is not needed. First, connect the AC

Adapter (supplied) to the AC Adapter Input receptacle at the rear of the balance then connect

the AC plug to an electrical outlet.

Figure 2-3. Rear and bottom view of balance

Battery Installation

Install the four “AA” batteries with polarity as shown in the battery compartment.

Note:

After power on, it is recommended to let the balance warm up for at least 5 minutes before

using it.

2.5 Initial Calibration

When the Balance is first installed, and when it is moved to another location, it must be

calibrated to ensure accurate weighing results. The balance can be manually calibrated with

external masses. Have the appropriate calibration masses available before beginning

calibration. Refer to the Calibration Section for masses and calibration procedure.

AC Adapter Input Jack

Battery Compartment Cover

Interface Connection

Security Switch

Weigh Below Hole

Security slot (Anti-theft lock slot)

EN-4 SCOUT

TM

SERIES BALANCES - SKX

3. OPERATION

3.1 Controls

Figure 3-1. Scout Control Panel

TABLE 3-1. Button Functions

Button

Primary Function

(Short Press)

Zero/On

Turns the balance

on

If balance is On,

sets Zero

Print

Sends the current

value to the

selected COM ports

if AUTOPRINT is

set to Off.

Function

Initiates an

application mode.

Tare

Enter/clear a tare

value.

Secondary Function

(Long Press)

Zero/Off

Turns the balance

Off.

Units

Changes the

weighing unit.

Mode

Allows changing the

application mode.

Menu

Enter the User

menu.

Menu Function

(Short Press)

Yes

Accepts the current

setting on the

display.

No

Advances to the

next menu or menu

item.

Rejects the current

setting on the

display and

advances to the

next available

setting.

Back

Moves Back to

previous menu item.

Exit

Exits the User

menu.

Aborts the

calibration in

progress.

Notes:

1

Short Press: Press less than 1 second.

2

Long Press: Press and hold for more than 2 seconds

SCOUT

TM

SERIES BALANCES - SKX EN-5

Figure 3-2. Scout Display

TABLE 3-2. Display Symbols

Item

Description

Item

Description

1

Battery charge symbol

7

Pointer symbols

2

Stable weight symbol

8

Kilogram, grain symbols

3

Negative symbol

9

Pound, Ounce, Pound:Ounce symbols

4

Center of Zero symbol

10

g/mol symbol

5

NET symbol

11

G symbol

6

Preset Tare symbol

12

Newton, Bluetooth symbols

3.2 Turning Balance On/Off

To turn the balance on, press and hold the On/Zero Off button for 1 second. The balance

performs a display test, momentarily displays the software version, and then enters the active

weighing mode.

To turn the balance off, press and hold the On/Zero Off button until OFF is displayed.

3.3 Calibration Operation

When the balance is operated for the first time, a span calibration is recommended to ensure

accurate weighing results. Before performing the calibration, be sure to have the appropriate

calibration weights. Ensure that the Security switch is set to unlocked position.

Press and hold Menu until [mMeNU] (Menu) is displayed. When the button is released, the display

will show [C.A.L]. Press Yes to accept. [SpaN] will then be shown. Press Yes to begin the span

calibration.

[--C--] will be displayed while zero reading is stored. Next, the display shows the calibration

weight value (press No to toggle value). Place the specified calibration mass on the pan. [--C--]

will be displayed while the reading is stored. The display will show [done] if the calibration was

successful. The balance returns to the previous application mode and is ready for use.

3.4 Weighing Mode

This mode is the factory default setting.

1. If needed, press and hold Mode until [wWeIGH] (Weigh) is displayed.

2. If required, place an empty container on the pan and press Tare.

3. Add sample to the pan or container. The display shows the weight of the sample.

2

3

4

1

5

6

8

9

10

11

12

7

EN-6 SCOUT

TM

SERIES BALANCES - SKX

3.5 Density Mode

This mode allows the user to calculate the specific gravity of a sample when using the density

kit. Density mode has been initiated when “G” and the current unit is displayed.

The sample is weighed in air suspended from the hook and then weighed in water. The formula

is

𝑑𝑟𝑦 𝑤𝑒𝑖𝑔ℎ𝑡

𝑑𝑟𝑦 𝑤𝑒𝑖𝑔ℎ𝑡 − 𝑤𝑒𝑡 𝑤𝑒𝑖𝑔ℎ𝑡

Preparation

Prepare the balance as shown below. Remove the balance pan, insert the hook and install the

beaker stand (beaker is not supplied). Then press the Zero/On button to turn the balance on.

Figure 3-3. Density Setup

Density setup

1. Press and hold Mode until [SPEC.Gr] is displayed. [Air.wWt] will then be displayed.

2. Place the sample on the hook as described above and press Yes to store the dry weight

value. [wW.wWt] will then be displayed.

3. Suspend the sample in water and press Yes to store the wet weight value. The specific

gravity value is now displayed and “G” is blinking while the unit icon is turned off.

Notes: Specific Gravity has no unit of measure.

For large samples it is recommended to use the weighing below feature instead of the

hook.

3.6 Mole Weighing Mode

To enter the Mole Weighing mode from any application mode, press and hold the Mode key

until [mMoLE] is displayed. When the Mode key is released, the display shows [Clr.mMS].

1. Press the Yes key to clear the stored Molar Mass. Press the No key to recall the existing

Molar Mass. If no Molar Mass was stored, the [Clr.mMS] display is skipped and inputting a

Molar Mass is required.

2. If there is a Molar Mass stored, the current Molar Mass will be displayed and flashing.

3. Press the No key to begin editing the Molar Mass.

5. Press the No key to increment the flashing digit.

6. Press the Back key to decrement the flashing digit.

7. Press the Yes key to accept the value and move one digit to the right.

Notes: If the setting exceeds the limit, the display returns to the previously stored value.

The most left number can be set to 0, 1, 2, 3, 4, 5, 6, 7, 8, 9,-. All other numbers can be

set to 0, 1, 2, 3, 4, 5, 6, 7, 8, 9.

The available settings are from 0.01 to 999.99.

The Molar Mass unit is g/mol.

Display Molar Mass:

Press Function key to display the existing Molar Mass value for 2 sec.

New Molar Mass:

To enter a new Molar Mass press and hold the Function/Mode key until [mMoLE] is displayed.

Beaker stand

Preparation

Air Weight

Wet Weight

SCOUT

TM

SERIES BALANCES - SKX EN-7

4. MENU SETTINGS

The User Menu allows the customizing of balance settings.

Note: Additional Sub-Menus may be available if Interface Options are installed. See Interface

User Manual for the additional setting information.

4.1 Menu Navigation

User Menu:

Sub-Menus

C.a.l

S.e.t.u.p

M.o.d.e

U.n.i.t

E.n.d

User Menu Items:

Span

Lin

Reset

Yes/No

Filter

Low/Med/High

AZT

0.5/1/3/Off

StableRange

0.5/1/2//5

Backlight

Off/On/Auto

Auto Tare

Off/On/On-acc

Auto Off

Off/1/5/10

Reset

Yes/No

Weighing

On/Off

Density

On/Off

Mole

On/Off

Reset

g

kg

N

oz

lb

lb:oz

End

Notes: Some Units/Modes may not be available in all models.

When the Security Switch is in locked position, the Calibration function is hidden, Units are

locked to the current setting.

Security switch:

4.2 Calibration Menu

Enter this menu to perform calibrations.

Span [SpaN]

Initiates a span calibration procedure (zero and span)

Lin [LIN]

Initiates a linearity calibration procedure (zero, mid-point and span).

End Cal [End]

Advance to the next menu or return to the top of the current menu.

Span: Perform

Linearity: Perform

End Calibration: Exit menu

No/Back

Long press -

Enter menu

Short press -

Accept

Short press –

Go

Next/Prev.

menu

Yes

Exit

Short press –

Exit

menu

EN-8 SCOUT

TM

SERIES BALANCES - SKX

4.3 Setup Menu

Enter this menu to set balance parameters.

Note: Bold always represents factory default value.

Reset [reset]

Reset the Setup menu to factory defaults.

NO = not reset

YES = reset

Filter [FiLtEr]

Set the amount of signal filtering.

LOW = less stability, faster stabilization time

MED = normal stability, stabilization time

HI = greater stability, slower stabilization time

AZT [AZt]

Set the automatic zero tracking functionality.

OFF = disabled

0.5d = the display will maintain zero until a change of 0.5 division per second has

been exceeded.

1d = the display will maintain zero until a change of 1 division per second has been

exceeded.

3d = the display will maintain zero until a change of 3 divisions per second has been

exceeded.

Stable Range [Stable]

Set the amount the reading can vary while the stability symbol remains on.

0.5d = 0.5 balance division

1d = 1 balance division

2d = 2 balance divisions

5d = 5 balance divisions

Back Light [b.Light]

Sets backlight functionality.

OFF = always off

ON = always on

AUTO = turns on when a button is pressed or the displayed weight changes.

Note: When connected with power pack, the backlight is always on.

Auto Tare [A.tArE]

Set the automatic tare functionality.

OFF = Automatic Tare is disabled

ON = the first stable gross weight is tared

ON-ACC = stable gross loads within the accept limits are tared (in Check weighing mode)

Reset: no, yes

Filter: Low, Med, High

Auto Zero Tracking: off, 0.5d, 1d, 3d

Stable: 0.5d, 1d, 2d, 5d

Backlight: off, on, auto

Auto Tare: off, on, on-acc

Auto Off: off, 1, 5, 10

End Setup: Exit menu

SCOUT

TM

SERIES BALANCES - SKX EN-9

Auto off [A.OFF]

Set the automatic shut off functionality.

OFF = disabled

1 = powers off after 1 minute of no activity

5 = powers off after 5 minutes of no activity

10 = powers off after 10 minutes of no activity

End Setup [End]

Advance to the next menu or return to the top of the current menu.

4.4 Mode Menu

This menu activates modes so they will be available for use with the Mode button.

Reset [reset]

Reset the Mode menu to factory defaults.

NO = not reset

YES = reset

Weigh [wWEIGH]

Set the status.

OFF = disabled

ON = enabled

Density [spec.Gr]

Set the sub-mode

OFF = disabled

ON = enabled

Mole [mMole]

Set the sub-mode

OFF = disabled

ON = enabled

Advance to the next menu or return to the top of the current menu.

End Mode [End]

4.5 Unit Menu

This menu activates units so they will be accessible with the Units button. The units in the menu

must be turned “on” to be active.

Note: Available units vary by model and local regulations.

Reset: no, yes

Weigh: off, on

Density: off, on

Mole: off, on

End Mode: Exit menu

g: off, on

kg: off, on

N: off, on

oz: off, on

lb: off, on

lb:oz: off, on

End Unit: Exit menu

EN-10 SCOUT

TM

SERIES BALANCES - SKX

4.6 Additional Features

Weigh Below Hook

The Scout Balance is equipped with a weigh below hook for weighing below the balance.

The weigh below hook is located at the reverse side of the battery cover as shown below.

To use this feature, remove the red protective cover underneath for the weigh below opening.

Attention: Before turning the balance over, remove the Pan and Pan

Support (if present), and turn the transportation lock to “locked” position to

prevent damage.

Figure 4-2. Weigh below

The balance can be supported using lab jacks or any other convenient method. Ensure the

balance is level and secure and that the transportation lock has been released. Power on the

Balance, then use a string or wire to attach items to be weighed.

Figure 4-3. Weigh below application

Connecting the Interface

Use an optional interface connectivity kit to

connect the balance either to a computer or a

printer.

Below Interface kit accessories are available:

RS232, USB Host, USB Device, Ethernet,

Bluetooth

®*

.

Figure 4-4. Rear of the balance

* Interface kits may vary according to local regulations

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and

any use of such marks by OHAUS is under license.

Interface

connection

AC Adapter

Jack

Security Slot

Weigh Below Hook

Weigh Below Hook installed

Weigh below opening

SCOUT

TM

SERIES BALANCES - SKX EN-11

5. MAINTENANCE

5.1 Cleaning

WARNING: Electric Shock Hazard. Disconnect the equipment from the power

supply before cleaning. Electric Shock Hazard.

The housing may be cleaned with a cloth dampened with a mild detergent if necessary.

Attention: Do not use solvents, chemicals, alcohol, ammonia or abrasives to clean the housing

or control panel.

5.2 Troubleshooting

The following table lists common problems and possible causes and remedies.

If the problem persists, contact OHAUS or your authorized dealer.

TABLE 5-1

Symptom

Possible Cause

Cannot turn on

No power to balance

Poor accuracy

Improper calibration

Unstable environment

Cannot calibrate

Security switch in locked position

Err 8.1

Weight exceeds power on zero range.

Err 8.2

Weight below power on zero range.

Err 8.3

Over load (weight exceeds rated capacity)

Err 8.4

Under load (pan removed)

Err 8.5

Tare out of range

Err 8.6

Displayed value exceeds 999999 (possible in Totalization mode)

ref.err

Parts counting or percentage error – sample weight <1d. Balance

shows error then exits parts counting or goes to [Clr.ApU].

Lo.ref

Percent Reference weight or APW is too low for accurate results

CAL E

Fail to do calibration.

USB.Err

Cannot find menu or app file in U-disk.

5.3 Service Information

If the troubleshooting section does not resolve or describe your problem, contact your

authorized OHAUS service agent. For service assistance or technical support in the United

States call toll-free 1-800-672-7722 ext. 7852 between 8:00 AM and 5:00 PM EST. An OHAUS

product service specialist will be available to provide assistance. Outside the USA, please visit

our web site, www.ohaus.com to locate the OHAUS office nearest you.

5.4 Accessories

TABLE 5-2. ACCESSORIES

DESCRIPTION

Item Number

DESCRIPTION

Item Number

RS232 kit

30268982

Stacking Kit, x1

30268988

USB Host kit

30268983

Specific Gravity kit

30269020

USB Device Kit

30268984

Auxiliary Display Kit

30269019

Bluetooth Kit*

30268985

Carrying Case

30269021

Ethernet Kit

30268986

In-Use Cover

30269022

Stacking Kit, x6

30268987

Printers and Cables

Contact OHAUS

Note: * Bluetooth kit is only available in certain regions according to the local regulations.

EN-12 SCOUT

TM

SERIES BALANCES - SKX

6. TECHNICAL DATA

The technical data is valid under the following ambient conditions:

Indoor use only

Operating temperature range: +5 °C to +40 °C

Relative humidity: 10% to 80% at 31°C , decreasing linearly to 50% at 40°C, non-condensing

Altitude: Up to 2000 m

Power: AC power adaptor input 100-240V 50/60 Hz and output 5 V DC 1 A, or 4 AA batteries

Pollution degree: 2

Main supply voltage fluctuations: up to ± 10% of the nominal voltage

6.1 Specifications

TABLE 6-1. SPECIFICATIONS

Model

SKX123

SKX222

SKX422

SKX622

SKX1202

SKX2202

Capacity (g)

120

220

420

620

1200

2200

Readability (g)

0.001

0.01

Repeatability (Std. Dev.) (g)

0.002

0.01

0.02

Linearity (g)

0.003

0.01

0.02

0.03

Span Calibration Mass*

100 g

200 g

300 g

1 kg

2 kg

Linearity Calibration Mass

50, 100 g

100, 200 g

200, 400 g

300, 600 g

500 g, 1 kg

1 kg, 2 kg

Stabilization Time (s)

1.5

1

1.5

Construction

ABS plastic housing with 304 stainless steel (SST) pan

Draftshield

Yes

No

Calibration

User-selectable external span or linearity calibration / Digital with external weight

Tare Range

Full Capacity by subtraction

Weighing Units**

g, kg, N, oz, lb, lb:oz

Application Modes

Weighing, Density Determination, Mole Weighing

Typical Battery Life

80 hours

120 hours

80 hours

Specified Temperature

Range

10° C (50° F) to 40° C (104° F) at 10% to 80% relative humidity, non-condensing

Storage Conditions

-20° C (-4° F) to 55° C (131° F) at 10% to 90% relative humidity, non-condensing

Communication

RS232, USB Host, USB Device, Ethernet or Bluetooth*** (all available as accessory)

Display Type

Backlit LCD: 6-digit 7-segment with white LED backlight

Display Size

0.78 in / 20 mm digits

Pan Size (W x D)

Ø 93 mm /

3.7 in

Ø 120 mm / 4.7 in

170 x 140 mm /

6.7 x 5.5 in

Balance Dimensions

(W x D x H)

202 x 222 x

103 mm /

8 x 8.7 x 4.1

in

202 x 224 x 54 mm / 8 x 8.8 x 2.1 in

Shipping Dimensions

(W x D x H)

300 x 250 x 129mm / 11.8 x 9.8 x 5.1 in

Net Weight

1 kg / 2.2 lb

Shipping Weight

1.6 kg / 3.5 lb

Notes:

* Calibration weights are included with models up to 620g capacity for certain regions.

** Availability is dependent on model and region.

*** Bluetooth kit is only available in certain regions according to the local regulations

SCOUT

TM

SERIES BALANCES - SKX EN-13

TABLE 6-2. SPECIFICATIONS (Cont.)

Capacity x Readability:

Model

SKX123

SKX222

SKX422

SKX622

SKX1202

SKX2202

Gram (g)

120 x 0.001

220 x 0.01

420 x 0.01

620 x 0.01

1200 x 0.01

2200 x 0.01

Kilogram (kg)

/

1.2 x 0.00001

2.2 x 0.00001

Newton (N)

1.17679 x

0.00001

2.1574 x 0.0001

4.1188 x 0.0001

6.0801 x 0.0001

11.7679 x

0.0001

21.5744 x

0.0001

Ounce (oz)

4.23290 x

0.00005

7.7600 x 0.0005

14.8150 x

0.0005

21.8700 x

0.0005

42.3290 x

0.0005

77.6030 x

0.0005

Pound (lb)

/

1.36690 x

0.00005

2.64555 x

0.00005

4.85020 x

0.00005

Pound:Ounce (lb:oz)

/

1lb:5.8700oz x

0.0005oz

2lb:10.3290oz x

0.0005oz

4lb:13.6030oz x

0.0005oz

TABLE 6-3. SPECIFICATIONS (Cont.)

Model

SKX421

SKX621

SKX2201

SKX6201

SKX8200

Capacity (g)

420

620

2200

6200

8200

Readability (g)

0.1

1

Repeatability (Std. Dev.) (g)

0.1

1

Linearity (g)

0.1

0.2

1

Span Calibration Mass*

200 g

300 g

2 kg

5 kg

8 kg

Linearity Calibration Mass

200, 400 g

300, 600 g

1 kg, 2 kg

3 kg, 6 kg

4 kg, 8 kg

Stabilization Time (s)

1

Construction

ABS plastic housing with 304 stainless steel (SST) pan

Draftshield

No

Calibration

User-selectable external span or linearity calibration / Digital with external weight

Tare Range

Full Capacity by subtraction

Weighing Units**

g, kg, N, oz, lb, lb:oz

Application Modes

Weighing, Density Determination, Mole Weighing

Typical Battery Life

120 hours

80 hours

120 hours

Specified Temperature Range

10° C (50° F) to 40° C (104° F) at 10% to 80% relative humidity, non-condensing

Storage Conditions

-20° C (-4° F) to 55° C (131° F) at 10% to 90% relative humidity, non-condensing

Communication

RS232, USB Host, USB Device, Ethernet or Bluetooth*** (all available as accessory)

Display Type

Backlit LCD: 6-digit 7-segment with white LED backlight

Display Size

0.78 in / 20 mm digits

Pan Size (W x D)

Ø 120 mm /

4.7 in

170 x 140 mm / 6.7 x 5.5 in

Balance Dimensions (W x D x H)

202 x 224 x 54 mm / 8 x 8.8 x 2.1 in

Shipping Dimensions (W x D x H)

300 x 250 x 129mm / 11.8 x 9.8 x 5.1 in

Net Weight

1 kg / 2.2 lb

Shipping Weight

1.6 kg / 3.5 lb

Notes:

* Calibration weights are included with models up to 620g capacity for certain regions.

** Availability is dependent on model and region.

*** Bluetooth kit is only available in certain regions according to the local regulation

TABLE 6-4. SPECIFICATIONS (Cont.)

Capacity x Readability:

Model

SKX421

SKX621

SKX2201

SKX6201

SKX8200

Gram (g)

420 x 0.1

620 x 0.1

2200 x 0.1

6200 x 0.1

8200 x 1

Kilogram (kg)

/

2.2 x 0.0001

6.2 x 0.0001

8.2 x 0.001

Newton (N)

4.119 x 0.001

6.080 x 0.001

21.574 x 0.001

60.801 x 0.001

80.41 x 0.01

Ounce (oz)

14.815 x 0.005

21.870 x 0.005

77.600 x 0.005

218.700 x 0.005

289.25 x 0.05

Pound (lb)

/

1.3670 x 0.0005

4.8500 x 0.0005

13.6685 x 0.0005

18.080 x 0.005

Pound:Ounce (lb:oz)

/

1lb:5.870oz x

0.005oz

4lb:13.600oz x

0.005oz

13lb:10.700oz x

0.005oz

18lb:1.25oz x

0.05oz

EN-14 SCOUT

TM

SERIES BALANCES - SKX

6.2 Drawings

Figure 6.1 Dimensions

Model

A

B

C

with draftshield

202 mm / 8.0 in.

222 mm / 8.7 in.

103 mm / 4.1 in.

w/o draftshield

202 mm / 8.0 in.

224 mm / 8.8 in.

54 mm / 2.1 in.

6.3 Compliance

Compliance to the following standards is indicated by the corresponding mark on the product.

Mark

Standard

This product complies with the applicable harmonized standards of EU

Directives 2011/65/EU (RoHS), 2014/30/EU (EMC), 2014/35/EU (LVD) and

2014/31/EU (NAWI). The EU Declaration of Conformity is available online at

www.ohaus.com/ce.

EN 61326-1

CAN/CSA-C22.2 No. 61010-1

UL Std. No. 61010-1

Important notice for verified weighing instruments in the EU

When the instrument is used in trade or a legally controlled application it must be set up, verified

and sealed in accordance with local weights and measures regulations. It is the responsibility of

the purchaser to ensure that all pertinent legal requirements are met.

Weighing Instruments verified at the place of manufacture bear the following supplementary

metrology marking on the descriptive plate.

Weighing Instruments to be verified in two stages have no supplementary metrology marking on

the descriptive plate. The second stage of conformity assessment must be carried out by the

applicable weights and measures authorities.

If national regulations limit the validity period of the verification, the user of the weighing

instrument must strictly observe the re-verification period and inform the weights and measures

authorities

As verification requirements vary by jurisdiction, the purchaser should contact their local weights

and measures office if they are not familiar with the requirements.

SCOUT

TM

SERIES BALANCES - SKX EN-15

Disposal

In conformance with the European Directive 2002/96/EC on Waste Electrical and

Electronic Equipment (WEEE) this device may not be disposed of in domestic

waste. This also applies to countries outside the EU, per their specific

requirements.

Please dispose of this product in accordance with local regulations at the collecting point

specified for electrical and electronic equipment. If you have any questions, please contact

the responsible authority or the distributor from which you purchased this device.

Should this device be passed on to other parties (for private or professional use), the content

of this regulation must also be related.

Disposal instructions in Europe are available online at www.ohaus.com/weee.

Thank you for your contribution to environmental protection.

FCC Note

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV technician for help.

Industry Canada Note

This Class B digital apparatus complies with Canadian ICES-003.

ISO 9001 Registration

In 1994, OHAUS Corporation, USA, was awarded a certificate of registration to ISO 9001 by

Bureau Veritus Quality International (BVQI), confirming that the OHAUS quality management

system is compliant with the ISO 9001 standard’s requirements. On June 21, 2012, OHAUS

Corporation, USA, was re-registered to the ISO 9001:2008 standard.

EN-16 SCOUT

TM

SERIES BALANCES - SKX

LIMITED WARRANTY

OHAUS products are warranted against defects in materials and workmanship from the date of

delivery through the duration of the warranty period. During the warranty period OHAUS will

repair, or, at its option, replace any component(s) that proves to be defective at no charge,

provided that the product is returned, freight prepaid, to OHAUS. This warranty does not apply if

the product has been damaged by accident or misuse, exposed to radioactive or corrosive

materials, has foreign material penetrating to the inside of the product, or as a result of service

or modification by other than OHAUS. In lieu of a properly returned warranty registration card,

the warranty period shall begin on the date of shipment to the authorized dealer. No other

express or implied warranty is given by OHAUS Corporation. OHAUS Corporation shall not be

liable for any consequential damages.

As warranty legislation differs from state to state and country to country, please contact OHAUS

or your local OHAUS dealer for further details.

SCOUT

TM

SERIES BALANCES - SKX EN-17

1. INTRODUCCIÓN

Este manual contiene las instrucciones para la instalación, el funcionamiento y el

mantenimiento de las Balanzas de la gama Scout SKXSeries. Por favor, lea este manual en su

integridad antes de proceder a utilizar la balanza.

1.1 Definición de los símbolos y señales de advertencia

Las notas en materia de seguridad se hallan señalizadas con términos y símbolos de

advertencia. Los mismos pueden transmitir informaciones sobre cuestiones y alertas de

seguridad. Señalan cuestiones y advertencias de seguridad. Ignorar las indicaciones en materia

de seguridad puede ser causa de daños tanto personales como al dispositivo, averías y

lecturas erróneas.

Términos de advertencia

ALERTA Indica una situación de un nivel de riesgo o peligro medio, de la que

podrían resultar daños o incluso la muerte en el caso de no evitarse.

PRECAUCIÓN Indica una situación de un nivel de riesgo o peligro bajo, de la que

podrían resultar daños materiales, daños al dispositivo o las pérdida de

datos, o daños físicos, en el caso de no evitarse.

Atención Para informaciones de relevancia sobre el producto.

Nota Para informaciones de utilidad sobre el producto.

Símbolos de advertencia

Riesgos general Riesgos de descarga eléctrica

1.2 Precauciones de seguridad

PRECAUCIÓN : Lea atentamente todas las advertencias en material de

seguridad antes de proceder a la instalación, de llevar a cabo conexiones u

operaciones de mantenimiento en estos equipos. Del incumplimiento del

contenido de estas advertencias podrían resultar daños personales y/o

materiales. Conserve estas instrucciones para poder consultarlas en el futuro.

 Compruebe que la alimentación eléctrica de corriente AC está en el rango del voltaje de

entrada impreso en la etiqueta del adaptador.

 Conecte el adaptador AC únicamente a un enchufe compatible que disponga de toma de

tierra.

 No colocar la balanza de tal modo que resulte difícil de desconectar el adaptador AC de la

toma de corriente.

 Asegúrese de que el cable de corriente no represente un obstáculo potencial o pueda

provocar caídas y/o tropiezos.

 Este equipo ha sido concebido y fabricado para ser utilizado en espacios interiores, y

debería hacerse uso del mismo en emplazamientos secos.

 Haga funcionar el equipo únicamente en las condiciones ambientales señalas las

instrucciones del usuario.

 No hacer funcionar el equipo en entornos peligrosos o inestables.

 No dejar caer objetos o cargas sobre la bandeja.

 Hacer uso únicamente de los accesorios y periféricos aprobados por el fabricante.

 Desconectar el equipo de la red eléctrica antes de proceder a su limpieza o efectuar

operaciones de mantenimiento.

 Las operaciones de mantenimiento deben de ser únicamente llevadas a cabo por personal

autorizado.

2. INSTALACIÓN

La pagina sta caricando ...

Ohaus SKX8200 Manuale utente

Questo manuale è adatto anche per

Ohaus SKX8200 Manuale utente

in altre lingue

Documenti correlati

Altri documenti