SWITEL DE391 Manuale del proprietario
- Categoria
- Smartwatch
- Tipo
- Manuale del proprietario
Low−radiation cordless DECT/GAP telephone
Operating Instructions
DE 39x
1
3
1 Safety Information 4. . . . . . . . . . . . . .
2 Putting the Telephone into Operation 5.
3 Operating Elements 7. . . . . . . . . . . . .
4 Operating the Telephone 10. . . . . . . . .
5 Menu Structure 12. . . . . . . . . . . . . . . .
6 Telephoning 13. . . . . . . . . . . . . . . . . .
7 Phonebook 15. . . . . . . . . . . . . . . . . . .
8 Call Log 15. . . . . . . . . . . . . . . . . . . . .
9 Troubleshooting 16. . . . . . . . . . . . . . .
10 Technical Properties 17. . . . . . . . . . . .
11 Maintenance / Guarantee 18. . . . . . . . .
4
1 Safety Information
Please read this operating instruction manual thoroughly.
Intended use
The telephone is suitable for telephoning within a public telephone
network system. Any other use is considered unintended use.
Unauthorised modification or reconstruction is not permitted.
Under no circumstances open the device or complete any repair
work yourself.
Installation location
Prevent excessive exposure to smoke, dust, vibration, chemicals,
moisture, heat and direct sunlight.
Do not use the handset in potentially explosive areas.
Power adapter plug
Attention: Only use the power adapter plug supplied because other power
supplies could damage the telephone. Ensure access to the power adapter
plug is not obstructed by furniture or such.
Batteries
Attention: Never throw batteries into a fire. Only use batteries of the same
type! Pay attention to correct polarity! If the polarity of the batteries is incor-
rect, there is a risk of explosion of the charging station.
Power failure
The telephone cannot be used to make calls in the event of a
power failure. Always keep a cord connected telephone which op-
erates without an external power supply available in case of
emergency situations.
Medical equipment
Attention: Never use the telephone in the vicinity of medical equipment.
Effects on such equipment cannot be fully ruled out.
DECT
1
telephones can cause an unpleasant humming sound in
hearing aids.
1
DECT: Digital Enhanced Cordless Telecommunication = Stan-
dard for cordless telephones.
2
5
Disposal
In order to dispose of your device, bring it to a collection
point provided by your local public waste authorities (e.g. re-
cycling centre). The adjacent symbol indicates that the de-
vice must not be disposed of in normal domestic waste! Ac-
cording to laws on the disposal of electronic and electrical
devices, owners are obliged to dispose of old electronic
and electrical devices in a separate waste container.
Batteries must be disposed of at the
point of sale or at the appropriate
collection points provided by the
public waste authorities.
Packaging materials must be disposed of according to local re-
gulations.
2 Putting the Telephone into Operation
Safety information
Attention: It is essential to read the Safety Information in Chapter 1 before
starting up.
Checking the package contents
The package contains:
Contents
DE 39X
391 392
1
393
1
394
1
Base station with power
adapter plug
1 1 1 1
Charging station with power
adapter plug
− 1 2 3
Handset 1 2 3 4
Telephone connection cable 1 1 1 1
Batteries 2 4 6 8
Operating instructions 1 1 1 1
1
Refer to the www.switel.com web site to see if this telephone
set is already available.
6
Connecting the base station
Attention: Position the base station at least 1 m away from other electronic
devices, otherwise there is a risk of mutual disturbance.
Connect the base station as illustrated in the diagram. For reasons
of safety, only use the power adapter plug and telephone connec-
tion line supplied.
Mains power outlet
Telephone line socket
Attention: With regard to the base station, use the power
adapter plug, model No. SW−075030EU bearing the
output data: 7,5 V, 300 mA.
Connecting the charging station
1
Connect the charging station as
illustrated in the diagram. For
safety reasons, only use the
power adapter plug supplied.
Attention: With regard to the charging station, use the power adapter plug,
model No. SW−075020EU bearing the
output data: 7,5 V, 200 mA.
Inserting the batteries
Insert the batteries in the open bat-
tery compartment. Only use batteries
of the type AAA NiMH 1,2 V.
Pay attention to correct polarity.
Close the battery compartment.
1
Only applies to telephone sets with at least two handsets
Section Package contents" on Page 5.
Mains power outlet
3
7
Charging the batteries
Before the handset is used for the first time, insert it in the base/charging
station for at least 24 hours.
When the handset is inserted in the base/charging station
properly, you will hear an acoustic confirmation signal. The
handset warms up during the charging process. This is normal
and does not represent a risk. Do not charge the handset with
charging units from other manufacturers. The current battery
charge status is indicated in the display:
Full Half empty Low Empty
Setting the display language
Select a language (cf. Menu Structure"):
> Handset > Language >...
3 Operating Elements
The buttons in this operating manual are subsequently depicted
with a uniform contour. Slight deviations in the appearance of the
icons on the buttons compared to those depicted in this manual
are possible.
8
Handset
1 Display
2 Open calls log /
Scroll upwards
3 Menu / OK button
4 Open calls log /
Scroll downwards
5 Phonebook /
Cancel process
6 Conference call
7 Internal call
8 R button /
Handset on/off
9 Key lock
10 Pause / Redialling
11 Take call /
End call
12 Delete / Muting
Base station
1 Paging button
2 Charge contacts
1
2
3
4
5
6
8
10
7
11
9
12
1
2
9
Charging station
1
1 Charge contacts
Low radiation operation (ECO mode)
Default settings = ECO-MODE → OFF
The telephone can be set up so that the radiation power is re-
duced; Page 12.
= ECO MODE → ON.
Reductions, with ECO mode activated, in comparison to a stan-
dard DECT cordless telephone:
Both in Call mode as well as in Standby mode, the radiation is re-
duced considerably when ECO mode is activated as compared to
standard, cordless DECT telephones.
If necessary, you can increase the range of the telephone system by swit-
ching ECO MODE off Page 12 (ECO MODE →
OFF).
1
Only applies to telephone sets with at least two handsets
Section Package contents" on Page 5.
1
10
4 Operating the Telephone
Display and notation of operating sequences
Enter the number
Press the button depicted
briefly
3 sec Press the button depicted for
3 seconds
5678
or Digits or icon in the display
Icons in the display
Icon Description
1 Internally assigned call number of the handset
05:08:03 Timer display
ext External call
int Internal call
Flashing: New calls have been registered in the call
log.
The key lock is activated.
MUTE The microphone is switched off (muting).
On: The connection to the base station is good.
Flashing: The connection to the base station is poor.
Programming the basic settings
Programming the basic settings relates to adapting the various
handset settings to your own personal needs. Press the but-
ton to cancel the process. If no button is pressed over a period of
15 sec., the process is automatically terminated and none of the
modifications made are saved. Proceed as follows:
11
Programming the handset
, /,
HANDSET
, ,
Ringing volume for external calls
/,
EXT RING VOL
, , / ,
VOLUME OFF
to
VOLUME 5
, .
Ringing volume for internal calls
/,
INT RING VOL
, , / ,
VOLUME OFF
to
VOLUME 5
, .
Ringing melody for external calls
/,
EXT MELODY
, , / ,
MELODY 1
to
MELODY 5
, .
Ringing melody for internal calls
/,
INT MELODY
, , / ,
MELODY 1
to
MELODY 5
, .
Setting the language
/,
LANGUAGE
, , / , .
Programming the setup
, /,
SETUP
, ,
Tone / Pulse dialling mode
/,
DIAL MODE
, , / ,
TONE DIAL
/
PULSE DIAL
, .
Flash (recall) time (Flash 1 = 90 ms, Flash 2 = 250 ms)
/,
RECALL
, , / ,
RECALL 1
/
RECALL 2
, .
Ringing volume of base
/,
BASE VOLUME
, , / ,
VOLUME OFF
to
VOLUME 5
, .
4
12
Ringing melody of base
/,
BASE MELODY
, , / ,
MELODY 1
to
MELODY 5
, .
Restoring the default settings
1
/,
DEFAULT
, ,
PIN ?
, , ,
CONFIRM ?
, .
5 Menu Structure
Open the main menu by pressing the button. Use the
/ buttons to move to and select an option then confirm
it by pressing the button.
PHONEBOOK
ADD ENTRY
MODIFY ENTRY
DELETE ENTRY
SETUP BASE VOLUME
BASE MELODY
DEL HANDSET
PIN CODE
DIAL MODE
RECALL
DEFAULT
ECO MODE
HANDSET BEEP
INT RING VOL
EXT RING VOL
INT MELODY
EXT MELODY
AUTO ANSWER
NAME
LANGUAGE
HOT KEYS
1
The four−digit PIN is 0000.
5
13
KEYLOCK
DATE − TIME DATE SET
CLOCK SET
ALARM SET
REGISTER SELECT BASE
REG BASE
6 Telephoning
All descriptions in this operating manual assume that the handset
is in Standby mode.
Take a call (off−hook)
End a call (on−hook)
Make an external call , or ,
Redial the number , /, or
,
Dial from calls log /,
Dial from phone number
memory
,/,
Internal calls
Making an internal call
, e.g. .
There must be two or more handsets registered on the base sta-
tion in order to make internal calls.
Forwarding external calls internally / Conference calls
During a call: , e.g. .
After the internal party has answered, transfer the call by pressing
the button.
To start a conference call, wait for the party called to answer the
internal call and then press the # button.
If the handset called does not answer, take the external call back by pres-
sing and release the button.
14
Other functions
Function Button sequence
Switch the handset on /off 5 sec
Key lock on 3 sec
Key lock off ,
Receiver volume , /
Ringing melody volume /
while phone is ringing
Muting/Activating micro-
phone in handset
during the call
Locate handset (paging)
on the base station
Muting function
After muting the microphone, the caller can no longer hear you.
Displaying the duration of a call
The duration of a call is displayed in hours, minutes and seconds
during the call.
Registering a handset
If your handset is not registered on the base station, icons flash in
the display.
To register the handset, press the button on the base sta-
tion for five seconds and then proceed as follows:
, /,
REGISTER
, ,
/,
REG BASE
, ,
BASE 1 2 3 4
.
To register a handset from a different manufacturer, refer to the
operating manual supplied with the respective handset. The four−
digit PIN for your base station is 0000.
Up to four handsets can be registered on your base
station. However, you can only activate your handset
on one base station at a time.
6
7
15
7 Phonebook
Up to 50 phone numbers can be stored in the phonebook.
Each entry can be customised with its own individual ringtone
(5 melodies).
When the memory capacity is completely full, an existing entry must be
overwritten.
Creating phone book entries
, /,
PHONEBOOK
, , / ,
ADD ENTRY
, ,
NAME ?
, , ,
NUMBER ?
,
, , /,
MELODY 1
to
MELODY 5
, .
Modifying phonebook entries
, /,
PHONEBOOK
, , / ,
MODIFY ENTRY
, , / , , , , ,
, / ,
MELODY 1
to
MELODY 5
, .
8 Call Log
A total of 40 phone numbers are stored in a call log.
The caller number display function is an optional service offered by tele-
phone network providers. If this service is not offered, the incoming calls
are not displayed. Contact your network provider for further information.
Displaying numbers in the call log
, /.
Storing an entry in the call log in the phone number memory
, /, several times if necessary ,
ADD ?
,
,
NAME ?
, , confirm number ,
MELODY 1
to
MELODY 5
, .
Deleting phone numbers from the call log
, /, ,
DELETE ?
, .
16
9 Troubleshooting
Should problems arise with the telephone, please refer to the fol-
lowing information first. In the case of technical problems, you can
contact our hotline service, Tel. 0900 00 1675 within Switzerland
(Swisscom fees, via landline, at time of going to print: CHF
2.60/min). In the case of claims under the terms of guarantee,
please contact your sales outlet. There is a 2 year period of guar-
antee.
No dialling tone can be heard after actuating the Off−hook
button, the line is not engaged.
− Check the telephone connection at the base station and
the telephone line wall socket.
− Check the power plug connection at the base station and
the 230 V power socket.
− The line is engaged by another handset. Wait until the
connection is terminated.
Display message SEARCHING.
− Check the power plug connection at the base station and
the 230 V power socket.
− Reduce the range between handset and base station.
− Register handset.
Base station does not ring.
− Ringing tone is switched off −> Switch it on.
No indicators in the display.
− Handset is switched off −> Switch it on.
− Battery is empty −> Recharge it.
17
10 Technical Properties
Technical data
Feature Value
Standard DECT
1−
GAP
2
Power supply, base station: Input: 100−240 VAC,
50/60 Hz, 0,2 A max.
Output: 7.5 V DC / 300 mA
Power supply, charging station: Input: 100−240 VAC,
50/60 Hz, 0,2 A max.
Output: 7.5 V DC / 200 mA
Range Outdoors: Approx. 300 m
Indoors: Approx. 50 m
Standby Up to 250 h
Max. talk time Up to 12 h
Rechargeable batteries 2 x 1,2 V, size: AAA
Dialling mode Tone dialling mode
Pulse dialling mode
Permissible ambient temperature 10 °C to 30 °C
Permissible relative humidity 20 % to 75 %
Flash (Recall) function 90 ms, 250 ms
Declaration of Conformity
This device fulfils the requirements stipulated in the EU
directive:
1999/5/EU directive on radio equipment and tele-
communications terminal equipment and the mutual
recognition of their conformity. Conformity is con-
firmed by the CE symbol on the device.
To view the complete Declaration of Conformity, please refer to the
free download available on our web site, www.audioline.de.
1
DECT: Digital Enhanced Cordless Telecommunication = Standard for
cordless telephones.
2
GAP: Generic Access Profile = Standard for the interoperation of
handsets and base stations from other manufacturers.
18
11 Maintenance / Guarantee
Maintenance
Clean the housing surfaces with a soft, fluff−free cloth.
Never use cleaning agents or solvents.
Guarantee
SWITEL equipment is produced and tested according to the latest
production methods. The implementation of carefully chosen ma-
terials and highly developed technologies ensure trouble−free
functioning and a long service life. The terms of guarantee do not
apply where the cause of equipment malfunction is the fault of the
telephone network operator or any interposed private branch ex-
tension system. The terms of guarantee do not apply to the bat-
teries or power packs used in the products. The period of guaran-
tee is 24 months from the date of purchase.
All deficiencies related to material or manufacturing errors within
the period of guarantee will be redressed free of charge. Rights to
claims under the terms of guarantee are annulled following
tampering by the purchaser or third parties. Damage caused as
the result of improper handling or operation, incorrect positioning
or storage, improper connection or installation or Acts of God and
other external influences are excluded from the terms of guaran-
tee. In the case of complaints, we reserve the right to repair defect
parts, replace them or replace the entire device. Replaced parts or
devices become our property. Rights to compensation in the case
of damage are excluded where there is no evidence of intent or
gross negligence by the manufacturer.
If your device shows signs of defect during the period of guaran-
tee, please return it to the sales outlet in which you purchased the
SWITEL device together with the purchase receipt. All claims
under the terms of guarantee in accordance with this agreement
can only be asserted at the sales outlet. No claims under the
terms of guarantee can be asserted after a period of two years
from the date of purchase and hand−over of the product.
19
Notes
8
Version 1.0 − 24.07.2009
Declaration of Conformity
Diese Anlage entspricht der europäischen R&TTE Richtlinie.
Für die komplette Konformitätserklärung nutzen Sie bitte den kosten-
losen Download von unserer Website www.switel.com
.
Cet équipement est conforme à la directive européenne R&TTE.
Pour obtenir la déclaration de conformité intégrale, veuillez vous servir
du téléchargement gratuit de notre site Internet www.switel.com
.
Quest’apparecchiatura è conforme alla direttiva europea R&TTE.
Per la dichiarazione di conformità completa si prega di voler usufruire
del servizio gratuito di download dal nostro sito Internet www.switel.com
.
This equipment complies with the European R&TTE directive.
To view the complete Declaration of Conformity, please refer to the free
download available at our web site: www.switel.com
.
Service Hotline
Bei technischen Problemen können Sie sich an unsere Service−Hotline
unter Tel. 0900 00 1675 innerhalb der Schweiz (Kosten Swisscom bei
Drucklegung: CHF 2.60/min) wenden.
S’il s’agit de problèmes techniques, vous pouvez vous adresser à notre
hotline de service en Suisse en appelant le numéro 0900 00 1675 (frais
Swisscom à la date d’impression de ce manuel : CHF 2.60/min).
In caso di problemi tecnici è possibile rivolgersi alla nostra hotline di
assistenza tecnica chiamando al numero 0900 00 1675 valido per la
Svizzera (spese da rete Swisscom alla data di stampa: CHF 2.60 / min).
In the event of technical problems, you can contact our hotline service,
Tel. 0900 00 1675 within Switzerland (cost via Swisscom at time of going
to print: CHF 2.60/min).
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
SWITEL DE391 Manuale del proprietario
- Categoria
- Smartwatch
- Tipo
- Manuale del proprietario
in altre lingue
- English: SWITEL DE391 Owner's manual
Documenti correlati
-
SWITEL DCT7271 Manuale del proprietario
-
SWITEL DCT7071 Manuale del proprietario
-
-
-
-
SWITEL DF921 Manuale del proprietario
-
-
SWITEL DFT9971 Manuale del proprietario
-