Ryobi RLT26CDS Manuale utente
- Categoria
- Tagliaerba
- Tipo
- Manuale utente
Questo manuale è adatto anche per
RLT26CDS
COUPE-BORDURES MANUEL D’UTILISATION 1
STRING TRIMMER USER’S MANUAL 10
KANTENSCHNEIDER BEDIENUNGSANLEITUNG 18
RECORTADORA DE HILO MANUAL DE UTILIZACIÓN 27
TAGLIABORDI MANUALE D’USO 36
APARADOR DE RELVA MANUAL DE UTILIZAÇÃO 45
GRASTRIMMER GEBRUIKERSHANDLEIDING 54
TRIMMER INSTRUKTIONSBOK 63
TRÅDTRIMMER BRUGERVEJLEDNING 71
TRÅDTRIMMER BRUKSANVISNING 79
SIIMALEIKKURI KÄYTTÄJÄN KÄSIKIRJA 87
SZEGÉLYVÁGÓ HASZNÁLATI ÚTMUTATÓ 95
STRUNOVÁ SEKAČKA NÁVOD K OBSLUZE 104
ÅÖçáéäéëÄ êìäéÇéÑëíÇé èé ùäëèãìÄíÄñàà 112
TRIMMER MANUAL DE UTILIZARE 121
PODKASZARKA DO OBRZEŻY INSTRUKCJA OBSŁUGI 130
KOSILNICA Z NITKO UPORABNIŠKI PRIROČNIK 139
©I©A» KORISNI»KI PRIRU»NIK 148
TRIMMER KASUTAJAJUHEND 157
ŽOLIAPJOVĖ NAUDOJIMO VADOVAS 166
ROKAS PĻAUJMAŠĪNA LIETOTĀJA ROKASGRĀMATA 175
STRUNOVÁ KOSAČKA - VYŽÍNAČ NÁVOD NA POUŽITIE 184
íêàåÖê êöäéÇéÑëíÇé áÄ ìèéíêÖÅÄ 193
Important! It is essential that you read the instructions in this manual before mounting and operating
this machine.
FR
EN
DE
ES
IT
PT
NL
SV
DA
NO
FI
HU
CS
RU
RO
PL
SL
HR
ET
LT
LV
SK
BG
960401009-03.indd AI960401009-03.indd AI 2010/4/28 4:562010/4/28 4:56
Attention ! Il est indispensable que vous lisiez les instructions contenues dans ce manuel avant
le montage et la mise en service de l’appareil.
Important! It is essential that you read the instructions in this manual before mounting and operating
this machine.
Achtung! Bitte lesen Sie unbedingt vor Montage und Inbetriebnahme die Hinweise dieser Bedienungsanleitung.
¡Atención! Es imprescindible que lea las instrucciones de este manual antes del montaje y de la
puesta en servicio.
Attenzione! Prima di procedere al montaggio e alla messa in funzione, è indispensabile leggere
attentamente le istruzioni del presente manuale.
Atenção! É indispensável ler as instruções deste manual antes de montar e pôr em serviço.
Let op ! Het is absoluut noodzakelijk vóór montage en inbedrijfstelling de aanwijzingen in deze
handleiding te lezen.
Observera! Det är nödvändigt att läsa instruktionerna i denna bruksanvisning före montering och
driftsättning.
OBS! Denne brugsanvisning skal læses igennem inden montering og ibrugtagning.
Advarsel! Vennligst les instruksjonene i denne bruksanvisningen før du monterer og tar i bruk
maskinen.
Huomio! On ehdottoman välttämätöntä lukea tässä käyttöohjeessa annetut ohjeet ennen
asennusta ja käyttöönottoa.
!
Figyelem! Feltétlenül fontos, hogy a jelen használati útmutatóban foglalt előírásokat az
összeszerelés és az üzembe helyezés ellőt elolvassa!
Důležité upozornění! Před montáží nářadí a uvedením do provozu je nutné si přečíst následující pokyny.
ÇÌËχÌËe! èee‰ Ò·ÓÍÓÈ Ë Á‡ÔÛÒÍÓÏ ËÌÒÚÛÏeÌÚ‡ ÌeÓ·ıÓ‰ËÏÓ ÔÓ˜eÒÚ¸ ËÌÒÚÛ͈ËË ËÁ ̇ÒÚÓfl˘e„Ó
ÛÍÓ‚Ó‰ÒÚ‚‡.
Atenie! Este indispensabil sã citii instruciunile coninute în acest mod de utilizare înainte de montaj
i de punerea în funciune.
Uwaga! Przed montowaniem i uruchomieniem, koniecznie musicie się Państwo zapoznać
z zaleceniami zawartymi w niniejszym sposobie użycia.
Pomembno! Zelo pomembno je, da pred namestitvijo in prvo uporabo te naprave preberete
navodila v tem priročniku.
Upozorenje!
Vaæno je da upute u ovom KorisniËkom priruËniku proËitate prije postavljanja i uporabe ovog alata.
Dikkat! Montajdan ve aletin kullanımına başlamadan bu kılavuzda bulunan talimatları
okumanız gerekmektedir.
Tähtis! Lugege enne seadme kokkupanekut ja kasutamist kindlasti läbi selles juhendis
sisalduvad eeskirjad ja juhised!
Dėmesio! Prieš surinkdami ir paleisdami aparatą į darbą, reikia, kad jūs perskaitytumėte šiame
vadove esančias instrukcijas.
Uzmanību! Ir ļoti būtiski, lai jūs izlasītu norādījumus, kas sniegti šajā rokasgrāmatā, pirms ķeraties
pie ierīces montēšanas un iedarbināšanas!
Upzornenie! Je dôležité, aby ste si pred montážou a spustením zariadenia prečítali pokyny, ktoré sa
nachádzajú v tomto návode.
ÇÌËχÌËÂ! èÂ‰Ë Ò„ÎÓ·fl‚‡ÌÂ Ë ÔÛÒ͇Ì ̇ χ¯Ë̇ڇ  ‚‡ÊÌÓ ‰‡ ÔÓ˜ÂÚÂÚ ËÌÒÚÛ͈ËËÚ ‚
˙ÍÓ‚Ó‰ÒÚ‚ÓÚÓ Á‡ ÛÔÓÚ·‡.
960401009-03.indd AII960401009-03.indd AII 2010/4/28 4:562010/4/28 4:56
Sous réserve de modifications techniques / Subject to technical modifications / Technische Änderungen vorbehalten /
Bajo reserva de modificaciones técnicas / Con riserva di eventuali modifiche tecniche / Com reserva de modificações técnicas /
Technische wijzigingen voorbehouden / Med förbehåll för tekniska ändringar / Med forbehold for tekniske ændringer /
Med forbehold om tekniske endringer / Tekniset muutokset varataan / ! " /
A műszaki módosítás jogát fenntartjuk / Změny technických údajů vyhrazeny /
åÓ„ÛÚ ·˚Ú¸ ‚ÌeÒeÌ˚ ÚeıÌ˘eÒÍËe ËÁÏeÌeÌËfl /
Sub rezerva modificaiilor tehnice / Z zastrzeżeniem modyfikacji technicznych / Tehnične spremembe dopuščene
Podloæno tehniËkim promjenama / Teknik düzeltmeler hakkı saklıdır / Tehnilised muudatused võimalikud /
Pasiliekant teisę daryti techninius pakeitimus / Paturam tiesības mainīt tehniskos raksturlielumus / Technické zmeny vyhradené /
èÓ‰ÎÂÊË Ì‡ ÚÂıÌ˘ÂÒÍË ÏÓ‰ËÙË͇ˆËË
960401009-03.indd AIII960401009-03.indd AIII 2010/4/28 4:562010/4/28 4:56
10
English(Original instructions)
EN
FR DE ES IT PT NL SV DA NO FI HU CS RU RO PL SL HR ET LT LV SK BG
10
SYMBOLS
Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning.
Proper interpretation of these symbols will allow you to operate the tool better and safer.
NAME EXPLANATION
Safety Alert Symbol Indicates danger, warning or caution. It means attention!!! Your safety is
involved.
Read Your Operator's Your manual contains special messages to bring attention to potential
Manual safety concerns as well as operating and servicing information. Please
read all the information carefully to ensure satisfaction and safe use.
Wear eye, hearing Wear eye, hearing and head protection when operating this equipment.
Keep bystanders away Keep all bystanders at least 15 m away.
Ricochet Danger of Ricochet.
No blade Do not install any type of blade on this unit.
RPM Decal Rotational direction and maximum speed of the shaft for the cutting
attachment.
Boots Wear non-slip safety footwear when using this equipment.
Gloves Wear non-slip, heavy-duty gloves.
No Smoking Do not smoke when mixing fuel or filling fuel tank.
Petrol Use unleaded gasoline intended for motor vehicle use with an octane
rating of 91 ([R+M]/2) or higher.
Oil Use synthetic 2-stroke oil for air cooled engines.
Mix Petrol and Oil Mix the fuel mix thoroughly and also each time before refuelling.
and head protection
960401009-03.indd 10960401009-03.indd 10 2010/4/28 4:562010/4/28 4:56
11
English(Original instructions)
EN
FR DE ES IT PT NL SV DA NO FI HU CS RU RO PL SL HR ET LT LV SK BG
Thank you for buying a Ryobi trimmer.
Your new trimmer has been engineered and manu-
factured to Ryobi’s high standard for dependability, ease
of operation, and operator safety. Properly cared for, it will
give you years of rugged, trouble-free performance.
INTENDED USE
This product should only be used outdoors.
The product is intended for cutting long grass, weed, and
similar vegetation at or about ground level. The cutting
plane should be approximately parallel to the ground
surface. The product should not be used to cut or trim
hedges, bushes or other vegetation where the cutting
plane is not parallel to the ground surface.
WARNING
To reduce the risk of injury, the user must read
and understand the operator’s manual.
WARNING
Do not attempt to operate this trimmer until you
have read thoroughly and understood completely
all instructions, safety rules etc contained in
this manual. Failure to comply may result in
accidents involving fire, electric shock or serious
personal injury. Save operator’s manual and
review frequently for continuing safe operation,
and instructing others who may use this tool.
READ ALL INSTRUCTIONS.
GENERAL SAFETY RULES
Q For safe operation, read and understand all
instructions before using the trimmer. Follow all safety
instructions. Failure to follow all safety instructions
listed below, can result in serious personal injury.
Q Do not allow children or untrained individuals to use
this unit.
Q Never start or run the engine in a closed or poorly
ventilated area; breathing exhaust fumes can kill.
Q Clear the work area before each use. Remove all
objects such as rocks, broken glass, nails, wire,
or string which can be thrown or become entangled in
the bump head.
Q Wear full eye and hearing protection while operating
this unit.
Q Wear heavy long pants, boots, and gloves. Do not
wear loose fitting clothing, short pants, jewellery of
any kind, or use with bare feet.
Q Secure long hair so it is above shoulder level to
prevent entanglement in any moving parts.
Q Keep all bystanders, children, and pets at least 15 m
away.
Q Do not operate this unit when you are tired, ill, or
under the influence of alcohol, drugs, or medication.
Q Do not operate in poor lighting.
Q Keep firm footing and balance. Do not overreach.
Overreaching can result in loss of balance or
exposure to hot surfaces.
Q Keep all parts of your body away from any moving part.
Q Do not touch area around the muffler or cylinder of
the trimmer, these parts get hot from operation.
Q Always stop the engine and remove the spark plug
wire before making any adjustments or repairs except
for carburetor adjustments.
Q Inspect the unit before each use for loose fasteners,
fuel leaks, etc. Replace any damaged parts before use.
Q The string head will rotate during carburetor
adjustments.
Q It has been reported that vibrations from hand-held
tools may contribute to a condition called Raynaud’s
Syndrome in certain individuals. Symptoms may
include tingling, numbness and blanching of the
fingers, usually apparent upon exposure to cold.
Q Hereditary factors, exposure to cold and dampness,
diet, smoking and work practices are all thought to
contribute to the development of these symptoms.
Q It is presently unknown what, if any, vibrations or extent
of exposure may contribute to the condition. There are
measures that can be taken by the operator to possibly
reduce the effects of vibration:
a) Keep your body warm in cold weather. When
operating the unit wear gloves to keep the hands
and wrists warm. It is reported that cold weather is
a major factor contributing to Raynaud’s Syndrome.
b) After each period of operation, exercise to increase
blood circulation.
11
SYMBOLS
NAME EXPLANATION
Switch On/Off Switch
I = ON to Run
O = OFF to Stop
Conforms to all regulatory standards in the country in the EU where
the product is purchased.
960401009-03.indd 11960401009-03.indd 11 2010/4/28 4:562010/4/28 4:56
12
English(Original instructions)
EN
FR DE ES IT PT NL SV DA NO FI HU CS RU RO PL SL HR ET LT LV SK BG
c) Take frequent work breaks. Limit the amount of
exposure per day.
Q If you experience any of the symptoms of this condition,
immediately discontinue use and see your physician
about these symptoms.
Q Keep the tool well maintained, fasteners tightened
and worn parts replaced.
Q Mix and store fuel in a container approved for fuel.
Q Mix fuel outdoors where there are no sparks or flames.
Wipe up any fuel spillage. Move 9 m away from
refueling site before starting engine.
Q Stop the engine and allow to cool before refueling or
storing the unit.
Q Allow the engine to cool; empty the fuel tank and
secure the unit from moving before transporting in a
vehicle.
SPECIFIC SAFETY RULES FOR TRIMMER USE
Q Replace bump head if cracked, chipped, or damaged
in anyway. Be sure the bump head is properly
installed and securely fastened. Failure to do so can
cause serious injury.
Q Make sure all guards, straps, deflectors and handles
are properly and securely attached.
Q Use only the manufacturer's replacement line in the
cutting head. Do not use any other cutting attachment.
Q Never operate unit without the safety guard in place
and in good condition.
Q Maintain a firm grip on both handles while trimming.
Keep bump head below waist level. Never cut with
the bump head located over 76 cm or more above the
ground.
12
SPECIFICATION
RLT26CDS
Weight (kg)
- Without fuel, without string head, without guard 3.98
- Without fuel with string head 4.35
Fuel tank volume [cm
3
or (L)] 250 or (0.25)
Cutting swath (mm) 432
Engine displacement (cm
3
/
cc) 26
Line diameter (mm) 2.0
Maximum engine performance
(in accordance with ISO 8893) (kW) 0.65
Maximum rotational frequency
of the the spindle (min-
1
) 12,000
Engine speed (rotational frequency)
at recommended max. spindle
rotational frequency (min-
1
) 12,000
Engine speed (rotational frequency)
at idle (min-
1
) 2,800-3,800
Fuel consumption (in accordance
with ISO 8893) at max.
engine performance [kg/h or (L/h)] 0.33 or (0.45)
Specific fuel consumption
(in accordance with ISO 8893)
at max. engine performance [g/kW.h or (L/kW.h)] 508 or (0.7)
Vibration level idling (m/s
2
)
- Front handle 7.7
- Rear handle 4.5
Vibration level racing (m/s
2
)
- Front handle 11.1
- Rear handle 12.9
Sound pressure level
(in accordance with EN ISO 22868) [LpA (dB A)] 100
Measured sound pressure level (dB A) 108
Sound power level (in accordance
with EN ISO 22868) [LwA (dB A)] 109
960401009-03.indd 12960401009-03.indd 12 2010/4/28 4:562010/4/28 4:56
13
English(Original instructions)
EN
FR DE ES IT PT NL SV DA NO FI HU CS RU RO PL SL HR ET LT LV SK BG
DESCRIPTION
Please refer to Fig.1
1. Primer Bulb
2. Choke Lever
3. Fuel Cap
4. Starter Grip
5. On / Off Switch
6. Throttle Trigger
7. Rear Handle
8. Front Handle
9. Shaft
10. Safety Guard
11. Bump Head
12. Cutting Line
13. Knob
14. Throttle Lock
15. Idle Speed Screw
ASSEMBLY
Please refer to Fig. 2.
WARNING
If any parts are damaged or missing, do not
operate this tool until the parts are replaced.
Failure to heed this warning could result in
serious personal injury.
WARNING
Do not attempt to modify this product or create
accessories not recommended for use with this
product. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
WARNING
To prevent accidental starting that could cause
serious personal injury, always disconnect the
engine spark plug wire from the spark plug when
assembling parts.
WARNING
Never attach or adjust any attachment while
power head is running. Failure to stop the engine
may cause serious personal injury.
WARNING
Be certain the knob is fully tightened before
operating equipment; check it periodically for
tightness during use to avoid serious injury.
OPERATION
Read the operation manual and follow all
warnings and safety instructions.
Wear eye protection and ear protection.
Keep all bystanders, especially children and
pets, at least 15 m from the operating area.
FUEL AND REFUELING
HANDLING THE FUEL SAFELY
Q Always handle fuel with care, it is highly flammable.
Q Always refuel outdoors where there are no sparks
and flames. Do not inhale fuel vapors.
Q Do not let petrol or oil come in contact with your skin.
Q Keep petrol and oil away from the eyes. If petrol
or oil comes in contact with the eyes, wash them
immediately with clean water. If irritation is still
present, see a doctor immediately.
Q Clean up spilled petrol immediately.
MIXING THE FUEL
(Fig. 3)
Q This product is powered by a 2-stroke engine and
requires pre-mixing petrol and 2-stroke oil. Pre-mix
unleaded petrol and 2-stroke engine oil in a clean
container approved for petrol.
Q This engine is certified to operate on unleaded petrol
intended for automotive use with an octane rating
of 91 ([R + M] / 2) or higher.
Q Do not use any type of pre-mixed petrol / oil from fuel
service stations, this includes the pre-mixed petrol / oil
intended for use in mopeds, motorcycles, etc.
Q Use synthetic 2-stroke oil only. Do not use automotive
oil or 2-stroke outboard oil.
Q Mix 2% synthetic 2-stroke oil into the petrol. This is a
50:1 ratio.
Q Mix the fuel thoroughly and also each time before
fueling.
Q Mix in small quantities. Do not mix quantities larger
than usable in a 30 day period. Synthetic 2-stroke oil
containing a fuel stabilizer is recommended.
FILLING THE TANK
Q Clean surface around fuel cap to prevent
contamination.
Q Loosen fuel cap slowly to release pressure and to
keep fuel from escaping around the cap.
Q Carefully pour fuel mixture into the tank. Avoid spillage.
13
960401009-03.indd 13960401009-03.indd 13 2010/4/28 4:562010/4/28 4:56
14
English(Original instructions)
EN
FR DE ES IT PT NL SV DA NO FI HU CS RU RO PL SL HR ET LT LV SK BG
Q Prior to replacing the fuel cap, clean and inspect
the gasket.
Q Immediately replace fuel cap and hand tighten.
Wipe up any fuel spillage. Move 9 m away from
refueling site before starting engine.
Note: It is normal for smoke to be emitted from a new
engine during and after first use.
WARNING
Always shut off engine before fueling. Never add
fuel to a machine with a running or hot engine.
Move at least 9 m from refueling site before
starting engine. Do not smoke!
1 Litre + 20 ml =
2 Litres + 40 ml =
3 Litres + 60 ml = 50:1 (2%)
4 Litres + 80 ml =
5 Litres + 100 ml =
STARTING AND STOPPING (Fig. 4)
WARNING
Never start or run the engine inside a closed or
poorly ventilated area; breathing exhaust fumes
can kill.
NOTE: Be sure to return the stop switch to the "I" (RUN)
position before trying to start unit.
To start a cold engine:
DO NOT squeeze the throttle trigger until the engine
starts and runs.
Lay the trimmer on a flat, bare surface.
PRIME - Press the primer bulb 10 times.
SET the start lever to the START position.
PULL the rope quickly and sharply straight up until
the engine starts.
Then squeeze the trigger to run.
NOTE: Squeezing and releasing the throttle trigger
releases the start lever to the RUN position.
If the engine stalls, set the start lever to the RUN position
"
". Then pull starter rope until the unit starts.
To start a warm engine:
Make sure carburettor is set to RUN position.
PULL the rope quickly and sharply straight up until the
engine starts.
To stop the engine:
Press and hold the switch in the stop “ O ” position until
the engine stops.
OPERATING THE TRIMMER (Fig. 5)
Hold the trimmer with the right hand on the rear handle
and the left hand on the front handle. Keep a firm grip
with both hands while in operation. Trimmer should be
held at a comfortable position with the rear handle about
hip height.
Always operate trimmer at full throttle. Cut tall
grass from the top down. This will prevent grass from
wrapping around the shaft housing and bump head
which may cause damage from overheating. If grass
becomes wrapped around the bump head, stop the
engine, disconnect the spark plug wire, and remove the
grass. Prolonged cutting at partial throttle will result in oil
dripping from the silencer.
CUTTING TIPS (Fig. 6)
When cutting make sure the cutter head is at a slight angle
as shown while still approximately parallel to the ground
surface. In tall grass cut from the top down to ensure the
moving parts do not get tangled with the long grass.
Move the head in steady strokes from right to left as you
work through the grass.
ADVANCING THE LINE (Fig. 7)
If the line becomes short, tap the head on the ground
as shown to extend more line. Take care not to ‘crash’ it
against a hard surface.
MAINTENANCE
WARNING
Use only original manufacturer's replacement
parts, accessories and attachments. Failure to
do so can cause possible injury, poor perfor-
mance and may void your warranty.
You may make adjustments and repairs described
here. For other repairs, have the trimmer serviced by
an authorised service agent.
Consequences of improper maintenance may
include excess carbon deposits resulting in loss of
performance and discharge of black oily residue
dripping from the silencer.
Make sure all guards, straps, deflectors and handles
are properly and securely attached to avoid the risk of
personal injury.
the cutting attachment must not rotate in idle mode. If
this requirement is not satisfied, the idle speed needs
adjustment (Fig.10) or the machine needs an urgent
maintenance by a qualified technician.
14
960401009-03.indd 14960401009-03.indd 14 2010/4/28 4:562010/4/28 4:56
15
English(Original instructions)
EN
FR DE ES IT PT NL SV DA NO FI HU CS RU RO PL SL HR ET LT LV SK BG
SPOOL REPLACEMENT (Fig. 11)
LINE REPLACEMENT (Fig. 11)
Ensure the unit is in the off position
Remove the spark plug lead, to prevent accidental
starting.
Use 2.4mm diameter monofilament string.
Cut one piece of string approximately 6.0m in length
Rotate knob on string head until line on knob aligns
with arrows on top of string head.
Insert one end of string into eyelet located on the
side of the string head and push until string comes
out through eyelet on the other side. Continue to
push string through the string head until the middle
section of the string is inside the string head and
string outside the string head is evenly divided on
each side.
Rotate the knob on the string head counterclockwise
to wind the string
Wind the string until approximately 20cm remains
protruding from the string head.
CLEANING THE EXHAUST PORT AND
SILENCER
Depending on the type of fuel used, the type and amount
of oil used, and/or your operating conditions, the exhaust
port and silencer may become blocked with carbon
deposits. If you notice a power loss with your petrol
powered tool, a qualified service technician will need to
remove these deposits to restore performance.
SPARK ARRESTOR
The spark arrestor must be cleaned or replaced every
25 hours or yearly to ensure proper performance of
your product. Spark arrestors may be in different
locations depending on the model purchased. Please
contact your nearest service dealer for the location of the
spark arrestor for your model.
CLEANING THE AIR FILTER SCREEN (Fig. 8)
For proper performance and long life, keep air filter
screen clean.
Remove the air filter cover by pushing down on the latch
with your thumb while gently pulling on the cover.
Brush the air filter screen lightly to clean.
Replace the air filter cover by inserting the tabs on the
bottom of the cover into the slots on the air filter base;
push the cover up until it latches securely in place.
FUEL CAP
WARNING
A leaking fuel cap is a fire hazard and must be
replaced immediately.
The fuel cap contains a non-service able filter and a
check valve. A clogged fuel filter will cause poor engine
performance. If performance improves when the fuel cap
is loosened, check valve may be faulty or filter clogged.
Replace fuel cap if required.
SPARK PLUG REPLACEMENT (Fig. 9)
This engine uses a Champion RCJ-6Y or NGK BPMR7A
spark plug with .05 in. electrode gap. Use an exact
replacement and replace annually.
IDLE SPEED ADJUSTMENT (Fig. 10)
If the cutting attachment turns at idle, the idle speed
screw needs adjusting on the engine. Turn the idle speed
screw counterclockwise to reduce the idle RPM and
stop the cutting attachment movement. If the cutting
attachment still moves at idle speed, contact a service
dealer for adjustment and discontinue use until the repair
is made.
STORING THE PRODUCT
Clean all foreign material from the product. Store
idle unit indoors in a dry, well-ventilated area that is
in- accessible to children. Keep away from corrosive
agents such as garden chemicals.
Abide by all ISO and local regulations for the safe
storage and handling of petrol.
When storing 1 month or longer:
Drain all fuel from tank into a container approved for
petrol. Run engine until it stops.
15
960401009-03.indd 15960401009-03.indd 15 2010/4/28 4:562010/4/28 4:56
16
English(Original instructions)
EN
FR DE ES IT PT NL SV DA NO FI HU CS RU RO PL SL HR ET LT LV SK BG
16
TROUBLESHOOTING
IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM, CONTACT YOUR AUTHORISED SERVICE DEALER.
PROBLEM POSSIBLE CAUSE SOLUTION
Engine will not start. 1. Power switch is off.
2. No spark.
3. No fuel.
4. Engine is flooded.
5. Starter rope now harder to
pull than when new.
1. Make sure Switch is in the ON or "I" position
2. The spark plug may be damaged, remove it and
check for dirt and cracks. Replace with a new spark
plug.
3. Push primer bulb until bulb is full of fuel. If bulb
does not fill, primary fuel delivery sys tem is blocked.
Con tact a servicing dealer. If prim er bulb fills, engine
may be flooded, proceed to next item.
4. Remove spark plug, turn unit so spark plug hole is
aimed at the ground. Set start lever to “
” position
and pull starter cord 10 to 15 times. This will clear
excess fuel from en gine. Remove any fuel which
splashed on the product. Clean and reinstall spark
plug. Clean up any spilled fuel and move at least
9m away before restarting. Pull starter three times
with with start lever at “
”. If en gine does not start,
set start lever to “
” position and repeat normal
starting pro ce dure. If engine still fails to start, repeat
pro ce dure with a new spark plug.
5. Contact a servicing dealer.
Engine starts but will
not idle long enough to
engage throttle
Temperature can effect engine
idle time and rpm.
Flip start lever to RUN “
” position and pull starter
until engine starts.
Engine does not stop
when switch is turned
off
Electrical connection is loose/
unplugged
Set the start lever to CHOKE “
” to stop the engine.
Immediately stop using the product. Check electrical
connection on the bottom of the trimmer and make
sure it is properly connected. Contact servicing dealer
if the problem persists.
Engine starts but will
not ac cel er ate.
Engine requires approximately
three minutes to warm up.
Allow engine to completely warm up. If engine does
not accelerate after three minutes, contact a ser vic ing
dealer.
Engine starts but will
only run at high speed
at half choke.
Carburetor requires
adjustment.
Contact a ser vic ing dealer.
Engine does not reach
full speed and emits
ex ces sive smoke.
1. Check oil fuel mixture.
2. Air filter is dirty.
3. Spark arrestor screen is
dirty.
1. Use fresh fuel and the correct 2-stroke oil mix.
2. Clean air filter. Refer to Clean ing the Air Filter
Screen earlier in this manual.
3. Contact a servicing dealer.
Engine starts, runs,
and accelerates but will
not idle.
Idle speed screw on
carburetor requires
adjustment
Turn idle speed screw clockwise to increase idle speed.
(Fig.10) Ensure that after adjustment the cutting head
does not rotate at idle. Contact servicing dealer if the
problem persists.
960401009-03.indd 16960401009-03.indd 16 2010/4/28 4:562010/4/28 4:56
17
English(Original instructions)
EN
FR DE ES IT PT NL SV DA NO FI HU CS RU RO PL SL HR ET LT LV SK BG
Line will not advance. 1. Line welded to itself.
2. Not enough line on spool.
3. Line worn too short.
4. Line tangled on spool.
5. Engine speed too slow.
1. Lubricate with silicone spray.
2. Install more line. Refer to “Line Replacement” earlier
in this manual.
3. Pull lines while alternately pressing down on and
releasing bump head.
4. Remove line from spool and rewind. Refer to “Line
Replacement” earlier in this manual.
5. Advance line at full throttle.
Grass wraps round
shaft
housing and bump
head.
1. Cutting tall grass at ground
level.
2. Operating trimmer at part
throttle.
1. Cut tall grass from the top down.
2. Operate trimmer at full throttle.
Bump knob hard to turn.
Screws threads dirty or
damaged.
Clean threads and lubricate with grease - if no
improvement, replace bump knob.
Oil drips from silencer.
1. Operating trimmer at part
throttle.
2. Check oil/fuel mixture.
3. Air filter dirty.
1. Operate trimmer at full throttle.
2. Use fresh fuel and the correct synthetic 2-stroke oil
mix.
3. Clean per instruction in Maintenance Section.
NOTE: If your unit exhibits speci c performance problem(s) where the Troubleshooting section recommends a clockwise
screw adjustment on the carburetor and no adjustments have been made since original purchase, the unit should
be taken to an authorised service centre for repair. In most cases, the needed adjustment is a simple task for the
trained service representative.
960401009-03.indd 17960401009-03.indd 17 2010/4/28 4:562010/4/28 4:56
GARANTIE
(TRADUCTION À PARTIR DU MODE D'EMPLOI D'ORIGINE)
TTI garantit cet outil de jardinage contre les vices de fabrication et les
pièces défectueuses pour une durée de vingt quatre (24) mois, à compter
de la date de facture d'achat, sous réserve des limitations ci-après. Merci
de conserver votre facture originale comme preuve de date d'achat.
Cette garantie n'est valable que pour une utilisation personnelle
de l'outil, et en aucun cas pour des applications commerciales.
La présente garantie ne couvre pas les dommages et détériorations
provoqués par une mauvaise utilisation, une utilisation abusive, une
action accidentelle ou intentionnelle de l'utilisateur, une mauvaise
manipulation, une utilisation non raisonnable, une négligence, le
non-respect par l'utilisateur des consignes contenues dans le manuel
d'utilisation, une tentative de réparation par un professionnel non
qualifié, une réparation non autorisée, une modification du produit ou
l'utilisation d'accessoires et/ou de pièces non recommandés pour ce
produit.
Sont exclus de cette garantie les courroies, balais de charbon,
sacs, ampoules et toute autre pièce subissant une usure normale et
soumise à un remplacement obligatoire au cours de la période de
garantie. Sauf indication contraire stipulée dans les lois en vigueur,
cette garantie ne couvre pas non plus les frais de transport ou les
consommables tels que les fusibles.
Cette garantie limitée est nulle en cas d'effacement, modification ou
suppression des éléments d'identification de l'outil (marque, numéro
de série, etc.), si le produit n'a pas été acheté auprès d'un revendeur
agréé ou si ce produit a été vendu EN L'ÉTAT et / ou AVEC DÉFAUTS.
Dans le cadre des normes locales en vigueur, les limitations de
la présente garantie remplacent toute autre garantie, expresse ou
implicite, écrite ou orale, y compris toute garantie de QUALITÉ
MARCHANDE OU DESTINÉE À UN BUT SPÉCIFIQUE. NOUS NE
POURRONS EN AUCUN CAS ÊTRE TENUS RESPONSABLES
DE DÉGÂTS ACCIDENTELS, QU'ILS SOIENT MINEURS OU
CONSÉQUENTS. NOTRE RESPONSABILITÉ MAXIMALE NE
DÉPASSERA PAS LE COÛT D'ACHAT DU PRODUIT.
Cette garantie n'est valable que dans l'Union Européenne,
l'Australie et la Nouvelle Zélande. Pour les autres pays, merci de
contacter votre revendeur agréé Ryobi pour savoir si une autre
garantie s'applique.
LIMITED WARRANTY
(ORIGINAL INSTRUCTIONS)
TTI warrants this outdoor product to be free of defects in material or
workmanship for 24 months from the date of purchase by the original
purchaser, subject to the limitations below. Please keep your invoice as
proof of date of purchase.
This warranty is only applicable where the product is used for personal
and non-commercial purposes. This warranty does not cover damage or
liability caused by / due to misuse, abuse, accidental or intentional acts by
user, improper handling, unreasonable use, negligence, failure by end user
to follow operating procedures outlined in the user’s manual, attempted
repair by non-qualified professional, unauthorized repair, modification, or
use of accessories and/or attachments not specifically recommended by
authorized party.
This warranty does not cover belts, brushes, bags, bulbs or any part which
ordinary wear and tear results in required replacement during warranty
period. Unless specifically provided under applicable law, this warranty
does not cover transportation cost or consumable items such as fuses.
This limited warranty is void if the product’s original identification (trade
mark, serial number, etc.) markings have been defaced, altered or removed
or if product is not purchased from an authorized reseller or if product is
sold AS IS and / or WITH ALL FAULTS.
Subject to all applicable local regulations, the provisions of this limited
warranty are in lieu of any other written warranty, whether express or
implied, written or oral, including any warranty of MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL
WE BE LIABLE FOR SPECIAL, INCIDENTAL, CONSEQUENTIAL OR
INCIDENTAL DAMAGES. OUR MAXIMUM LIABILITY SHALL NOT
EXCEED THE ACTUAL PURCHASE PRICE PAID BY YOU FOR THE
PRODUCT.
This warranty is valid only in the European Union, Australia and New
Zealand. Outside these areas, please contact your authorized Ryobi
dealer to determine if another warranty applies.
EINGESCHRÄNKTE GARANTIE
(ÜBERSETZUNG DER ORIGINALEN ANLEITUNGEN)
TTI garantiert, dass dieses Produkt für den Außengebrauch im Hinblick
auf Material und Verarbeitungsgüte frei ist von allen Defekten, gültig für
einen Zeitraum von 24 Monaten ab Datum des Kaufs durch den originalen
Käufer, jedoch abhängig von den unten stehen-den Beschränkungen. Bitte
bewahren Sie Ihre Rechnung als Beweis des Kaufdatums auf.
Diese Garantie ist nur dann anwendbar, wenn das Produkt für
persönliche und nicht-kommerzielle Zwecke verwendet wird. Diese
Garantie erstreckt sich nicht auf einen Schaden oder Haftung, die
durch/aufgrund von falscher Anwendung, Missbrauch, zufälligen oder
absichtlichen Handlungen des Nutzers verursacht wurden, oder durch
ei-ne unsachgemäße Handhabung, Nachlässigkeit oder das Versäumnis
des Endnutzers, die im Benutzerhandbuch angegebenen Anweisungen
zu befolgen, oder die versuchte Repa-ratur durch nicht-qualifiziertes
Personal, die Modifikation oder Nutzung von Zubehörtei-len und/oder
Zusatzgeräten, die von der autorisierten Partei nicht ausdrücklich
empfohlen werden.
Diese Garantie erstreckt sich nicht auf Riemen, Bürsten, Taschen, Birnen
oder jedes sonstige Teil, das einer gewöhnlichen Abnutzung unterliegt
und einen Ersatz im Rahmen des Garantiezeitraums erforderlich macht.
Außer für den Fall einer ausdrücklichen ge-setzlichen Vorschrift erstreckt
sich diese Garantie nicht auf Transportkosten oder Verbrauchsgüter wie
Sicherungen.
Diese eingeschränkte Garantie ist nichtig, falls die originalen Kennzeichen
(Handelsmar-ke, Seriennummer etc.) beschädigt, geändert oder entfernt
wurden, oder falls das Produkt nicht bei einem autorisierten Einzelhändler
gekauft, oder falls das Produkt in seinem IST-Zustand und / oder MIT
ALLEN VORHANDENEN MÄNGELN verkauft wurde.
Abhängig von den anwendbaren lokalen Vorschriften gelten die
Bestimmungen dieser Garantie anstelle jeder anderen schriftlichen
Garantie, sie sei schriftlich oder mündlich, einschließlich jeder
VERTRIEBSGARANTIE ODER GARANTIE IM HINBLICK AUF DIE
GEEIGNETHEIT FÜR EINEN BESTIMMTEN ZWECK. UNTER KEINEN
UM-STÄNDEN HAFTEN WIR FÜR SPEZIAL-, ZUFALLS-, FOLGE-
ODER UNFALL-SCHÄDEN. UNSERE GESAMTHAFTUNG SOLL DEN
TATSÄCHLICHEN KAUF-PREIS, DER FÜR DAS PRODUKT GEZAHLT
WURDE, NICHT ÜBERSCHREITEN.
Diese Garantie ist nur gültig in der Europäischen Union, Australien
und Neuseeland. Bitte kontaktieren Sie Ihren autorisierten Ryobi-
Händler außerhalb dieser Regio-nen, um festzulegen, ob eine andere
Garantieleistung anzuwenden ist.
FR
EN
DE
960401009-03.indd 202960401009-03.indd 202 2010/4/28 4:572010/4/28 4:57
DÉCLARATION DE CONFORMITÉ EC (Traduction à partir du mode d'emploi d'origine)
Fabricant: Homelite Far East Co.,Ltd
Adresse: 24/F, CDW building, 388 Castle Peak Road, Tsuan Wan, HongKong.
Nom et adresse de la personne habilitée à établir le dossier technique:
Nom: Simon Del-Nevo (Directeur de l'Outillage Extérieur à Moteur)
Adresse: Techtronic Industries Europe, Middle East and Africa, Medina House, Field House Lane, Marlow, Bucks.
SL7 1TB - United Kingdom
Déclarons par la présente que le produit
Catégorie .................................................................................................
COUPE-BORDURES
Modèle ..................................................................................................................RLT26CDS
Numéro de série ............................................................................... Voir plaque signalétique
Année de fabrication.........................................................................Voir plaque signalétique
• est conforme aux réserves applicables de la Directive Machinerie(2006/42/EC)
• est conforme aux réserves applicables des autres Directives EC- suivantes
Directive EMC(2004/108/EC),
Directive Emissions Sonores (2000/14/EC modi ée 2005/88/EC), et
Directive Emissions Gazeuses (97/68/EC modi ée 2004/26/EC).
Nous déclarons par ailleurs que
• les parties suivantes (parties/clauses des) standards Européens harmonisés ont été utilisées
EN ISO 11806 :2008
EN ISO 22867 :2008
EN ISO 22868 :2008
EN ISO 14982:1998
EN ISO 3744:1995
Niveau de puissance sonore mesuré 108 dB(A)
Niveau de puissance sonore garanti 109 dB(A)
Méthode d’évaluation de conformité de l’Annexe V/ Directive 2000/14/EC
Fait à, le: Hong Kong, 29/10/2009 Signature: Andrew John Eyre (BEng, CEng, MIET)
Vice président de l'Ingénierie
EC DECLARATION OF CONFORMITY (Original Instructions)
Manufacturer: Homelite Far East Co.,Ltd
Address: 24/F, CDW building, 388 Castle Peak Road, Tsuan Wan, HongKong.
Name and address of the person authorised to compile the technical le:
Name: Simon Del-Nevo (Director of Outdoor Power Equipment)
Address: Techtronic Industries Europe, Middle East and Africa, Medina House, Field House Lane, Marlow, Bucks.
SL7 1TB - United Kingdom
Herewith we declare that the products
Category ................................................................................... STRING TRIMMER
Model .....................................................................................................RLT26CDS
Serial number .................................................................... See product rating label
Year of Construction .......................................................... See product rating label
• is in conformity with the relevant provisions of the Machinery Directive (2006/42/EC)
• is in conformity with the provisions of the following other EC-Directives
EMC Directive (2004/108/EC),
Noise Emission Directive (2000/14/EC amended by 2005/88/EC), and
Gas Emission Directive (97/68/EC amended by 2004/26/EC).
And furthermore, we declare that
• the following (parts/clauses of) European harmonised standards have been used
EN ISO 11806 :2008
EN ISO 22867 :2008
EN ISO 22868 :2008
EN ISO 14982:1998
EN ISO 3744:1995
Measured sound power level 108 dB(A)
Guaranteed sound power level 109 dB(A)
Conformity assessment method to Annex V/ Directive 2000/14/EC
Place, date: HongKong, 29/10/2009 Signature: Andrew John Eyre (BEng, CEng, MIET)
Vice president of Engineering
FR
EN
960401009-03.indd 210960401009-03.indd 210 2010/4/28 4:572010/4/28 4:57
TECHTRONIC INDUSTRIES EMEA
Medina House, Field house Lane,
Marlow, Bucks
SL7 1TB-UNITED KINGDOM
RYOBI TECHNOLOGIES (UK) LIMITED.
Medina House, Field house Lane,
Marlow, Bucks
SL7 1TB-UNITED KINGDOM
Tel: + 44 (0) 1628 894400
Fax: + 44 (0) 1628 894401
Technical Helpline : + 44 (0) 800 389 0305
TECHTRONIC INDUSTRIES FRANCE SAS
Immeuble Le Grand Roissy
Z.A. du Gué - 35 rue de Guivry
77990 LE MESNIL AMELOT FRANCE
Phone: + 33(0)1 60 94 69 70
Fax: + 33(0)1 60 94 69 79
RYOBI BELGIUM
Avenue des Pâquerettes, 55
Zoning artisanal - bâtiment 5
B - 1410 Waterloo
BELGIQUE
Tel : + 32(0) 2357 8140
Fax : + 32(0) 2357 8149
TTI ITALIA SRL
Via Fratelli Gracchi, 39
20092 Cinisello Balsamo (MI)
Italia
Tel : + 39(0) 5923 8408
Fax : + 39(0) 5924 6960
TECHTONIC INDUSTRIES IBERIA S.L
Av. De la Industria,52
Coslada – Madrid – España
Tel: 91 485 12 10
TECHTRONIC INDUSTRIES SOUTH AFRICA
CO. (PTY) LTD
P.O Box 83888, South Hills, Johannesburg, 2136
South Africa
TECHTRONIC INDUSTRIES (ASIA) CO., LTD.
24/F, CDW Building,
388 Castle Peak Road,
Tsuen Wan, Hong Kong.
Tel : + 852 2402 6888
RYOBI TECHNOLOGIES GMBH
Itterpark 4
D-40724 Hilden
DEUTSCHLAND
Tel: + 49 (0) 2103 2958-0
Fax: + 49 (0) 2103 2958-29
RYOBI TECHNOLOGIES GMBH
Vertriebsbüro Österreich
Schinitzgasse 13
A-8605 Kapfenberg
Tel.: + 43 (0) 3862 23590-0
Fax: + 43 (0) 3862 23590-25
TECHTRONIC INDUSTRIES AUSTRALIA PTY LIMITED.
Building B, Rosehill Industrial Estate,
3 Shirley Street,
Rosehill NSW 2142
AUSTRALIA
Tel: (02) 8892 1800 or 1300 361 505
Fax: 1800 807 993
TECHTRONIC INDUSTRIES (NZ) LIMITED.
27 Clemow Drive, Mt Wellington
PO Box 12-806, Penrose, Auckland
NEW ZEALAND
Tel: + 64 (0) 9 573 0230
Free Call: +64 0800 279 624
Fax: + 64 (0) 9 573 0231
A&M MIDDLE EAST FZCO
P.O.Box 61254
Jedel Ali, Dubai,
UNITED ARAB EMIRATES
Tel.: + 9714 8861399
Fax: + 9714 8861400
TECHTRONIC INDUSTRIES DENMARK APS
Stamholmen 147, 4.
DK-2650 Hvidovre
Denmark
Tlf 43 56 55 55, Fax 43 56 55 56
E-mail: [email protected]
TECHTRONIC INDUSTRIES NORWAY AS
Tlf.: 800 12 493, Faks: 800 12 492
E-mail: [email protected]
TECHTRONIC INDUSTRIES SWEDEN AB
Tel (+46) 08 24 60 30. fax (+46) 08 24 60 31.
E-mail: [email protected]
TECHTRONIC INDUSTRIES FINLAND OY
Tel. 0800 1 09000, Fax 0800 1 09001
Email: [email protected]
960401009-03
960401009-03.indd 222960401009-03.indd 222 2010/4/28 4:572010/4/28 4:57
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
Ryobi RLT26CDS Manuale utente
- Categoria
- Tagliaerba
- Tipo
- Manuale utente
- Questo manuale è adatto anche per
in altre lingue
- English: Ryobi RLT26CDS User manual
- français: Ryobi RLT26CDS Manuel utilisateur
- Deutsch: Ryobi RLT26CDS Benutzerhandbuch
Documenti correlati
Altri documenti
-
MTD bosmaaier 1000w Original Operating Instructions
-
Simplicity WEED TRIMMER Manuale utente
-
Craftsman 41ADZ42C799 Manuale del proprietario
-
Craftsman 316711970 Manuale del proprietario
-
Robin NB223, NB253 Manuale del proprietario
-
-
Dolmar MS-3202 Manuale utente
-
-
Mountfield MT2801J Istruzioni per l'uso
-