Yealink BHM711 Guida utente

Bluetooth Headset

BH71 Workstation/BH71 Workstation Pro

English | Deutsch | Español | Français

Quick Start Guide (V1.1)

www.yealink.com

Note: Some third-party accessories may be incompatible with the headset, so we

strongly recommend that you use Yealink accessories only.

1

BH71 Workstation

BHM711 Headset

Power Adapter

BHB710 Station

USB 3.0 Cable

(Type-C to Type-A)

Quick Start Guide

USB 2.0 Cable

(Micro USB to Type-A)

Eartips (S, M, L/M is pre-installed)

E

N

G

L

I

S

H

Note: Some third-party accessories may be incompatible with the headset, so we

strongly recommend that you use Yealink accessories only.

2

BH71 Workstation Pro

BHM711 Headset

Power Adapter

BHB710 Station

USB 3.0 Cable

(Type-C to Type-A)

Quick Start Guide

USB 2.0 Cable

(Micro USB to Type-A)

Eartips

(S, M, L/M is pre-installed) BHC71P Charging Case BT51A Dongle

3

Charge Headset

It takes approximately 90 minutes to fully charge the headset.

or

4

Charging Indicator

•

Charging Case

• Station

Charging: Flash green

Charging is complete: Off

Charging: Solid green

Charging is complete: Off

Power on/off

Red

"Power off"

Blue

"Power on, XX% battery remains"

5

Connect Your Devices

The USB hub is an extension port of the PC. After the station is connected to the PC,

you can plug a USB driver into the USB hub port, or plug the phone and charging

case into the USB hub port for charging.

Connect the desk phone, PC or busylight to station.

5V

USB 3.0 hub port

6

Pair Your Devices

•

Pair your station

-

Tap Bluetooth->Settings in the station.

-

Enable Open discover.

Pair with headset

Place the headset on the station and the headset will automatically pair with the

station.

Pair with phone

Bluetooth

OT H E R DE V IC E

OTH

E

Yea

R

link

BH

D

71

EVICE

Yealink BH71 Workstation

Note: One headset or station can only connect to two devices at a time.

B

A

7

•

Pair your headset

Slide and hold the switch for 3 seconds until the LED indicator flashes red and

blue automatically.

"Pairing mode"

Pair with phone

"mobile one connected"

Pair with PC（BH71 Workstation Pro）

"PC

The BT51A is pre-paired to the headset and ready for use.

Note: The BT51A can only connect to a device at a time.

Bluetooth

OTHER DEVIC E

OTHE

Ye a

R

lin k

B H

D

71

EVICE

Yealink BH71

connected"

A

B

8

❶

Fit the Headset

•

Right ear wearing

1.

Take out the headset, as shown in figure . Twist the speaker to the left, and

then rotate microphone boom down.

2.

Before wearing, you can adjust

the height of the speaker up or down

to get the perfect fit for your ear.

3.

Put the eartip in your ear and slide headset over and behind your ear, then

press gently toward your ear. Fine-tune the headset according to your own

situation.

Retractable

9

❶

•

Left ear wearing

1.

Take out the headset, as shown in figure . Twist the speaker to the right, and

then rotate microphone boom down.

2.

For wearing methods, please refer to steps 2 and 3 of the right ear wearing.

❶

❷

❸

Note:

Remove your eyeglasses before donning the headset for best fit.

Change the eartip for a better fit. Eartips with three size options — S/M/L (medium

pre-installed).

10

Call Control

Accept

Reject (It is not applicable to Teams)

End

In the idle status, invoke the Teams client

In the idle status, activate Cortana (requires Microsoft's support)

Call Button

Mute Button

Volume Button (360 ° rotating)

2s

X 1

X 2

X 1

11

Software Management

Download it from the Yealink website https://www.yealink.com/product/yuc.

Note: It needs to be used with Yealink USB Connect of version 0.35.x.x or later.

NEED MORE HELP?

Technical support

https://ticket.yealink.com

FAQ & User manual

http://support.yealink.com

12

Safety Guide

1.

Do not disassemble the product by yourself or bring it near fire and water to

avoid short circuit leakage or damage to the product.

2.

Do not use the product in high temperature, humidity, and corrosive

environment to avoid damaging the circuit and causing failure to charge or other

failures.

3.

Do not expose the product to corrosive liquids. Otherwise, it will cause severe

damage.

4.

Do not disassemble or re-equip the product for any reason to avoid secondary

failure and burnout.

5.

Do not place the product in an environment below -10°C or above 60°C.

6.

Do not knock, throw or shake the product because rough methods will

damage the internal circuit board structure.

If your headset needs warranty service, the process is quick and easy. Please

go to https://ticket.yealink.com/page/headset/warranty-service.html and submit

RMA Claim to Yealink.

Regulatory Notices

Operating Ambient Temperatures

•

Operating temperature: 0 °C to +40 °C (+32 °F to +104°F)

•

Relative humidity: 5% to 90%, noncondensing

•

Storage temperature:-30°C to +70°C (-22 to +158°F)

Warranty

Our product warranty is limited only to the unit itself, when used normally in accordance with the operating instructions and the system

environment. We are not liable for damage or loss resulting from the use of this product, or for any claim from a third party. We are not

liable for problems with Yealink device arising from the use of this product; we are not liable for financial damages, lost p rofits, claims from third

parties, etc., arising from the use of this product.

Explanation of the symbols

•

DC symbol

is the DC voltage symbol.

•

WEEE Warning symbol

To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical

and electronic equipment, end users of electrical and electronic equipment should understand the meaning of the crossed-out

wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately.

Restriction of Hazardous Substances Directive (RoHS)

This device complies with the requirements of the EU RoHS Directive. Statements of compliance can be obtained by contacting support@

yealink.com.

Safety Instructions

Save these instructions. Read these safety instructions before use!

General Requirements

• Before you install and use the device, read the safety instructions carefully and observe the situation during operation.

• During the process of storage, transportation, and operation, please always keep the device dry and clean, avoid collision and

crash.

• Please attempt not to dismantle the device by yourself. In case of any discrepancy, please contact the appointed maintenance

center for repair.

• Please refer to the relevant laws and statutes while using the device. Legal rights of others should be respected as well.

Environmental Requirements

• Place the device at a well-ventilated place. Do not expose the device under direct sunlight.

• Keep the device dry and free of dust.

•

Do not place the device on or near any inflammable or fire-vulnerable object, such as rubber-made materials.

•

Keep the device away from any heat source or bare fire, such as a candle or an electric heater.

Operating Requirements

• Do not let a child operate the device without guidance.

• Do not let a child play with the device or any accessory in case of accidental swallowing.

• Please use the accessories provided or authorized by the manufacturer only.

• The power supply of the device shall meet the requirements of the input voltage of the device. Please use the provided surge

protection power socket only.

• Before plugging or unplugging any cable, make sure that your hands are completely dry.

• Do not spill liquid of any kind on the product or use the equipment near water, for example, near a bathtub, washbowl, kitchen

sink, wet stationment or near a swimming pool.

• During a thunderstorm, stop using the device and disconnect it from the power supply. Unplug the power plug and the

Asymmetric Digital Subscriber Line (ADSL) twisted pair (the radio frequency cable) to avoid lightning strike.

• If the device is left unused for a rather long time, disconnect it from the power supply and unplug the power plug.

• When there is smoke emitted from the device, or some abnormal noise or smell, disconnect the device from the power supply,

and unplug the power plug immediately.

•

Contact the specified maintenance center for repair.

•

Do not insert any object into equipment slots that is not part of the product or auxiliary product.

•

Before connecting a cable, connect the grounding cable of the device first. Do not disconnect the grounding cable until you

disconnect all other cables.

Battery Requirements

• Do not immerse the battery into water, which could short-circuit and damage the battery.

•

Do not expose the battery to an open flame or leave the battery where it could be subjected to extremely high temperatures,

which could cause the battery to explode.

• Do power the handset off before removing the battery.

• Do not try to use the battery for the power supply of any device other than this handset.

• Do not open or mutilate the battery, released electrolyte is corrosive and may cause damage to your eyes or skin.

• Use only the rechargeable battery pack delivered with the handset or those rechargeable battery packs expressly

recommended by Yealink.

• Defective or exhausted battery should never be disposed of as municipal waste. Return old battery to the battery supplier, a

licensed battery dealer or a designated collection facility.

Cleaning Requirements

• Before cleaning the device, disconnect it from the power supply.

•

Use a piece of soft, dry and anti-static cloth to clean the device.

•

Keep the power plug clean and dry.

Troubleshooting

The unit cannot supply power to Yealink device.

There is a bad connection with the plug.

1. Clean the plug with a dry cloth.

2. Connect it to another wall outlet.

The usage environment is out of operating temperature range.

1. Use in the operating temperature range.

The cable between the unit and the Yealink device is connected incorrectly.

1. Connect the cable correctly.

You cannot connect the cable properly.

1. You may have connected a wrong Yealink device.

2. Use the correct power supply.

Some dust, etc., may be in the port.

1. Clean the port.

Contact your dealer or authorized service facility for any further questions.

FCC CAUTION

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The BHB710 Station should be installed and operated with minimum distance 20cm between the radiator& your body.

ISED WARNING

This device complies with Innovation, Science and Economic Development Canada licence -exempt RSS standard(s). Operation is subject

to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the device.

Le présentappareilestconforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitationestautorisée

aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareildoit acc epter tout

brouillageradioélectriquesubi, mêmesi le brouillageest susceptible d’encompromettre le fonctionnement.

This Class B digital apparatus complies with Canadian ICES-003. Cetappareilnumérique de la classe B estconformeà la norme NMB-003 du

Canada.

The device is compliance with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance. For

BHB710 Station, the minimum distance from body to use the device is 20cm.

L'appareil est conforme aux directives d'exposition aux RF, les utilisateurs peuvent obtenir des informations canadiennes sur

l'exposition aux RF et la conformité. Pour la station BHB710, la distance minimale du corps pour utiliser l'appareil est de 2 0 cm.

Les communications effectuées au moyen de cetappareil ne sont pas necessairement protected des indiscrétions.

EU regulations

Supported frequency bands and power:

Bluetooth 2.4GHz <20dBm

contact information

YEALINK NETWORK TECHNOLOGY CO.,LTD.

No.666 Hu'an Rd. Huli District Xiamen City, Fujian, P.R. China

YEALINK (EUROPE) NETWORK TECHNOLOGY B.V.

Strawinskylaan 3127, Atrium Building, 8th floor, 1077ZX

Amsterdam, The Netherlands

YEALINK (USA) NETWORK TECHNOLOGY CO., LTD.

999 Peachtree Street Suite 2300, Fulton, Atlanta, GA, 30309, USA

Made in China

Yealink

- EaS::I UCIP -

CE

We,

YEALINK (XIAMEN) NETWORK TECHNOLOGY CO.,LTD

WWW.YEALINK.COM

De claration of Conformity

YEALINK(XIAMEI\) NETWORK TECHNOLOOY CO.,LTD

Address: No.666 Hu'an Rd. Huli District Xiamen City, Fujian, P.R. China

Manufacturer: YEALINK(X!AMEl\) NETWORK TECHNOLOGY CO.,LTD

Address: No.666 Hu'an Rd. HL1li District Xiamen City, Fujian, P.R. China

DATE: 28th /November/ 2022

declare that the product Type:

Bluetooth Headset Model:

BHB710

meets the essential requirements and other relevant provisions according to the following EC directive

Directive: 2014/30/EU, 2014/35/EU, RED 2014/53/EU

Conformity

The product complies with the following standards:

Safety: EN IEC 62368-1:2020+A11:2020

EMC: EN 55032:2015+A1:2020

EN 55035:2017+A11:2020

EN IEC 61000-3-2:2019+A1:2021

EN 61000-3-3:2013+A2:2021

ETSI EN 301489-1 VZ.2.3 (2019-11)

ETSI EN 301489-3 VZ.2.2 (2021-11)

ETSI EN 301 489-17 V3.2.4 (2020-09)

Radio: ETSI EN 300 328 V2.2.2 (2019-07)

ETSI EN 303 417 Vt.1.1 (2017·09)

Health: EN 624 79:2010; EN 50663:2017

Directive

2011/65/EU

and (EU] 2015/863

of the European Parliamentand of the Council of8 June

2011 and 4 June 2015 on the restriction of the use of certain hazardous substances in electrical and

electronic equipment(RoHS2.0)

Directive 2012/19/EU of the European Parliamentand of the Council of 4.July.2012 on Waste

electrical and electronic equipment(WEEE)

Regulation (EC) No.1907/2006 of the European Parliamcntand of the Council of 18.Dcccmbcr.2006

on Registration, Evaluation, Authorization, and Restriction of Chemicals (REACH)

NAME: Hu ahu Wang

DATE:

TITLE: Manager ')

f(w,,fv.,,

lf\)i:.,,,_

22/v•v/

2,J-,,

v

Y

--

eal

V

C

i

F

n

'

-

k

CE

We,

YEALINK (XIAMEN) NETWORK TECHNOLOGY CO.,LTD

WWW.YEALINK.COM

De claration of Conformity

YEALINK(XIAMEN) NETWORK TECH"'\./OLOGY CO.,LTD

Address: No.666 Hu'an Rd. H111i Oistl'ict Xiamen City, Fujian, P.R. China

Manufacturer: YEAUNK(XIAMEN) NJ:::'J'WORK '!'ECHNOLOGY CO.,LTD

Address: No.666 Hu'an Rd. Huli District Xia.men City, Fujian, P.R. China

DATE: 28th/November/2022

declare that the product Type:

Charging Case

Model: BHC71P

meets the essential requirements and other relevant provisions according to the following EC directive

Directive: 2014/30/EU, 2014/35/EU

Conformity

The product complies with the following standards:

Safety:EN !EC 62368·1:2020+A11:2020

EMC: EN 55032:2015+Al:2020

EN

55035:2017+A11:2020

EN IEC 61000-3-2:2019+A1:2021

EN

61000·3-3:2013+A2:2021

Directive 2011/65/EU and (EU) 2015/863

of the European Parliamentand of the Council of 8 June

2011 and

4

June 2015 on the restriction of the use of certain hazardous substances in electrical and

electronic equipment(RoHSZ.0)

Directive

2012/19/EU

of the European Parliamentand of the Council of 4.July.2012 on Waste

electrical and electronic equipment (WEEE)

Regulation (EC) No.1907/2006ofthe European Parliamentand of the Council of 18.December.2006

on Registration, Evaluation, Authorization, and Restriction of Chemicals (REACH)

NAME: Huahu Wang

DATE,

TITLE: Manager

Yealink

Manager '

- E c!S'o,I VcF> -

(€

We,

YEALINK (XIAMENJ NETWORK TECHNOLOGY CO.,LTD

WWW.YEALINK.COM

De claration of Conformity

YEALINK(X!Alv!E'l) NETWORK TECIINOLOGY CO.,LTD

Address: No.666 Hu'an Rd. Huli District Xiamen Cily, Fujian, P.R. China

Manufacturer: YEALINK(XIAME ) NETWORK TECHKOLOGY CO.,LTD

Address: No.666 Hu'an Rd. Huli Distl"ict Xiamen City, Fujian, P.R. China

DATE: 28th/November/2022

declare that the product Type:

Bluetooth Headset Model:

BHM711

meets the essential requirements and other relevant provisions according to the following EC directive

Directive: 2014/30/EU, 2014/35/EU, RED 2014/53/EU

Conformity

The product complies

with

the following standards:

Safety: EN !EC 62368-1:2020+A11:2020

EMC: EN 55032:2015+A1:2020

EN 55035:2017+A11:2020

EN !EC 61000-3-2:2019+A1:2021

EN 61000-3-3:2013+A2:2021

ETSI EN 301 489-1 V2.2.3 (2019-11)

ETSI EN 301489-17 V3.2.4 (2020-09)

Radio: ETSI EN 300 328 V2.2.2 (2019-07)

Health: EN 62479:2010; EN50663:2017

Directive 2011/65/EU and (EU) 2015/863 of the European Parliamentand of the Council of8 June

2011 and 4 June 2015 on the restriction of the use of certain hazardous substances in electrical and

electronic equipment(RoHSZ.01

Directive 2012/19/EUofthe European Parliamentand of the Council of 4.July.2012 on Waste

electrical and electronic equipment (WEEE)

Regulation (EC) No.1907/2006ofthe European Parliamentand of the Council of 18.December.2006

on Registration, Evalualion, Authorization, and Restriction of Chemicals (REACH)

NAME,

DATE,

Huahu Wang

y

Tel +86 592 57C2000

Fax +86 592 5702455

Addr 309, 3rd Fkxlr, No 16, Yun Ding North Road,

Hui District X1amen Otv Fu11an PR China

TITLE,

Hinweis: Einige Zubehörteile von Drittanbietern können mit dem Headset

inkompatibel sein. Wir empfehlen daher dringend, nur Zubehör von Yealink zu

verwenden.

18

BH71 Workstation Verpackungsinhalt

BHM711 Headset

Netzteil

BHB710 Basisstation

USB 3.0-Kabel

(Typ-C auf Typ-A)

Kurzanleitung

USB 2.0-Kabel

(Micro-USB auf Typ-A)

Ohrstöpsel

(S, M, L/Größe M ist ab Werk aufgesetzt)

D

E

U

T

S

C

H

Hinweis: Einige Zubehörteile von Drittanbietern können mit dem Headset

inkompatibel sein. Wir empfehlen daher dringend, nur Zubehör von Yealink zu

verwenden.

19

BH71 Workstation Pro Verpackungsinhalt

BHM711 Headset

Netzteil

BHB710 Basisstation

USB 3.0-Kabel

(Typ-C auf Typ-A)

Kurzanleitung

USB 2.0-Kabel

(Micro-USB auf Typ-A)

Ohrstöpsel

(S, M, L/Größe M ist

ab Werk aufgesetzt)

Lade-Etui BHC71P BT51A Dongle

La pagina sta caricando ...

Yealink BHM711 Guida utente

Yealink BHM711 Guida utente

in altre lingue

Documenti correlati

Altri documenti