Samsung DVD-P370 Manuale utente

DVD-P370

DVD-P375

™Y™KEYH DVD

DVD Player

DDVVDD

ÔÔÎÎÂÂÈÈ˙˙

2

PRECAUTIONS

1. Setting up

- Refer to the identification label located on

the rear of your player for its proper operat-

ing voltage.

- Install your player in a cabinet with ade-

quate ventilation holes. (7~10cm) Do not

block ventilation holes on any of the compo-

nents for air circulation.

- Do not push the disc tray in by hand.

- Do not stack components.

- Be sure to turn all components off before

moving the player.

- Before connecting other components to this

player, be sure to turn them off.

- Be sure to remove the disc and turn off the

player after use, especially if you are not

going to use it for a long time.

- The mains plug is used as a disconnect

device and shall stay readily operable at

any time.

2. For your safety

- This product utilizes a laser. Use of controls

or adjustments or performance of proce-

dures other than those specified herein may

result in hazardous radiation exposure.

- Do not open covers and do not repair your-

self. Refer servicing to qualified personal.

3. Caution

- Your player is not intended for industrial use

but for domestic purposes. Use of this prod-

uct is for personal use only.

- Apparatus shall not be exposed to dripping

or splashing ang no objects filled with liq-

uids, such as vases, shall be placed on the

apparatus.

- Exterior influences such as lightning and

static electricity can affect normal operation

of this player. If this occurs, turn the player

off and on again with the POWER button, or

disconnect and then reconnect the AC

power cord to the AC power outlet. The

player will operate normally.

- When condensation forms inside the player

due to sharp changes in temperature, the

player may not operate correctly. If this

occurs, leave the player at room tempera-

ture until the inside of the player becomes

dry and operational.

4. Disc

- Do not clean disc using record-cleaning

sprays, benzene, thinner, or other volatile

solvents that may cause damage to the disc

surface.

- Do not touch the disc’s signal surface. Hold

by the edges or by one edge and the hole

in the center.

- Wipe the dirt away gently; never wipe a

cloth back and forth over the disc.

5. Environmental info

- The battery used in this product contains

chemicals that are harmful to the environ

ment.

- So, dispose of batteries in the proper man

ner, according to federal, state, and local

regulations.

The product unit accompanying this user manual is

licensed under certain intellectual property rights of

certain third parties. This license is limited to private

non-commercial use by end-user consumers for

licensed contents. No rights are granted for

commercial use. The license does not cover any

product unit other than this product unit and the

license does not extend to any unlicensed product

unit or process conforming to ISO/OUR 11172-3 or

ISO/OUR 13818-3 used or sold in combination with

this product unit. The license only covers the use of

this product unit to encode and/or decode audio files

conforming to the ISO/OUR 11172-3 or ISO/OUR

13818-3. No rights are granted under this license for

product features or functions that do not conform to

the ISO/OUR 11172-3 or ISO/OUR 13818-3.

CAUTION: USE OF ANY CONTROLS,

ADJUSTMENTS, OR PROCEDURES OTHER

THAN SPECIFIED HEREIN MAY RESULT IN

HAZARDOUS RADIATION EXPOSURE.

3

BEFORE

YOU

ST

AR

T

English

1. Open the battery cover on the back of the remote

control.

2. Insert two AAA batteries.

Make sure that the

polarities (+ and -) are aligned correctly.

3. Replace the battery cover.

Remote Control

-

Batteries for Remote

Control (AAA Size)

User’s Manual

Video/Audio

Cable

Install Batteries in the Remote control

If remote control doesn’t operate

properly:

- Check the polarity + - of the batteries (Dry-Cell)

- Check if the batteries are drained.

- Check if remote control sensor is blocked by

obstacles.

- Check if there is any fluorescent lighting nearby.

Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Setup

General Features . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Disc Type and Characteristics . . . . . . . . . . . . . . . . 5

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Tour of the Remote Control . . . . . . . . . . . . . . . . . . 8

Connections

Choosing a Connection . . . . . . . . . . . . . . . . . . . . . 9

Basic Functions

Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Using the Search and Skip Functions . . . . . . . . . 16

Using the Display Function . . . . . . . . . . . . . . . . . 16

Using the Disc and Title Menu . . . . . . . . . . . . . . 17

Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Slow Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Advanced Functions

Adjusting the Aspect Ratio (EZ View) . . . . . . . . . 18

Selecting the Audio Language . . . . . . . . . . . . . . . 19

Selecting the Subtitle Language. . . . . . . . . . . . . . 19

Changing the Camera Angle . . . . . . . . . . . . . . . . 20

Using the Instant Replay/Skip Function . . . . . . . . 20

Using the Bookmark Function . . . . . . . . . . . . . . . 20

Using the Zoom Function . . . . . . . . . . . . . . . . . . . 21

Clips Menu for MP3/WMA/JPEG/MPEG4/

CD Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Folder Selection . . . . . . . . . . . . . . . . . . . . . . . . . . 21

MP3/WMA/CD Audio Playback. . . . . . . . . . . . . . . 22

MPEG4 Playback . . . . . . . . . . . . . . . . . . . . . . . . . 22

Picture CD Playback. . . . . . . . . . . . . . . . . . . . . . . 23

Changing Setup Menu

Using the Setup Menu . . . . . . . . . . . . . . . . . . . . . 24

Setting Up the Language Features . . . . . . . . . . . 25

Setting Up the Audio Options . . . . . . . . . . . . . . . . 26

Setting Up the Display Options . . . . . . . . . . . . . . 27

Setting Up the Parental Control . . . . . . . . . . . . . . 28

Reference

Firmware upgrade . . . . . . . . . . . . . . . . . . . . . . . . 29

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

T

ABLE OF

CONTENTS

Accessories

4

SETUP

General Features

Excellent Sound

Dolby Digital, a technology developed by Dolby

Laboratories, provides crystal clear sound reproduc-

tion.

Screen

Both regular and widescreen(16:9) pictures can be

viewed.

Slow Motion

An important scene can be viewed in slow motion.

Parental Control (DVD)

The parental control allows users to set the level

necessary to prohibit children from viewing harmful

movies such as those with violence, adult subject

matter, etc.

Various On-Screen Menu Functions

You can select various languages (Audio/Subtitle)

and screen angles while enjoying movies.

Progressive Scan

Progressive scanning creates an improved picture

with double the scan lines of a conventional inter-

laced picture.

EZ VIEW (DVD)

Easy View enables picture adjustment to match

your TV's screen size (16:9 or 4:3).

Digital Photo Viewer (JPEG)

You can view Digital Photos on your TV.

Repeat

You can repeat a song or movie simply by pressing

the REPEAT button.

MP3/WMA

This unit can play discs created from MP3/WMA

files.

Instant Replay (DVD)

This function is used to replay the previous 10

seconds of a movie from the current position.

Instant Skip (DVD)

This function skips playback ahead 10 seconds

MPEG4

This unit can play MPEG4 formats within an avi file.

Note

- Discs which cannot be played with this

player.

• DVD-ROM • DVD-RAM

• CD-ROM • CDV

• CDI • CVD

• CDGs play audio only, not graphics.

- Ability to play back may depend on recording

conditions.

• DVD-R, +R

• CD-RW

• DVD+RW, -RW (V mode)

- The unit may not play certain CD-R, CD-RW

and DVD-R due to the disc type or recording

conditions.

COPY PROTECTION

Many DVD discs are encoded with copy protection.

Because of this, you should only connect your DVD

player directly to your TV, not to a VCR. Connecting

to a VCR results in a distorted picture from copy-

protected DVD discs.

This product incorporates copyright protection

technology that is protected by methods claims of

certain U.S. patents and other intellectual property

rights owned by Macrovision Corporation and other

rights owners. Use of this copyright protection tech-

nology must be auzthorized by Macrovision

Corporation, and is intended for home and other

limited viewing uses only unless otherwise autho-

rized by Macrovision Corporation. Reverse engi-

neering or disassembly is prohibited.

PROGRESSIVE SCAN OUTPUTS

(525p)

“CONSUMERS SHOULD NOTE THAT NOT ALL

HIGH DEFINITION TELEVISION SETS ARE FULLY

COMPATIBLE WITH THIS PRODUCT AND MAY

CAUSE ARTIFACTS TO BE DISPLAYED IN THE

PICTURE, IN CASE OF 525 PROGRESSIVE

SCAN PICTURE PROBLEMS, IT IS RECOM-

MENDED THAT THE USER SWITCH THE CON-

NECTION TO THE ‘STANDARD DEFINITION’ OUT-

PUT. IF THERE ARE QUESTIONS

REGARDING YOUR TV SET COMPATIBILITY

WITH THIS MODEL 525p DVD PLAYER, PLEASE

CONTACT SAMSUNG'S CUSTOMER SERVICE

CENTER.”

5

English

This DVD player is capable of playing the following types of discs with the corresponding logos:

Disc Markings

Region Number

Both the DVD player and the discs are coded

by region. These regional codes must match in

order for the disc to play. If the codes do not

match, the disc will not play.

The Region Number for this player is

described on the rear panel of the player.

You must only insert one DVD disc at a time.

Inserting two or more discs will not allow to

play them back and it may cause damage to

the DVD player.

12 Cm

8 Cm

Single-sided 240 min.

Double-sided 480 min.

Single-sided 80 min.

Double-sided 160 min.

Audio

+

Video

- DVD contains excellent sound and

video due to Dolby Digital and MPEG-

2 system.

- Various screen and audio functions

can be easily selected through the on-

screen menu.

Disc Types (Logos)

Recording Types Disc Size Max. Playing Time Characteristics

DVD

12 Cm

8 Cm

74 min.

20 min.

Audio

- CD is recorded as a Digital Signal

with better audio quality, less distor-

tion and less deterioration of audio

quality over time.

AUDIO-CD

~

DIGITAL

SOUND

STEREO

PAL

Play Region Number

PAL broadcast system in U.K, France,

Germany, etc.

Dolby Digital disc

Stereo disc

Digital Audio disc

DTS disc

MP3 disc

DivX Certification

DivX, DivX Certified,

and associated logos are trademarks of

DivXNetworks, Inc and are used under

license

Disc Type and Characteristics

6

Front Panel Controls

Front Panel Display

Description

Total playing time/Displays various messages concerning operations such as PLAY,

STOP, LOAD ...

nodSC: No disc loaded.

OPEn: The disc tray is open.

LOAd: Player is loading disc information.

1. STANDBY/ON ( )

When STANDBY/ON is pressed on, the indicator goes

out and the player is turned on.

2. STANDBY indicator

When the unit is first plugged in, this indicator lights.

3. DISC TRAY

Place the disc here.

4. OPEN/CLOSE ( )

Press to open and close the disc tray.

5. DISPLAY

Operation indicators are displayed here.

6. SKIP ( / ) SEARCH

Allow you to search forward/backward through

a disc. Use to skip the title, chapter or track.

7. STOP ( )

Stops disc play.

8. PLAY/PAUSE ( )

Begin or pause disc play.

1

7

8

6

2

3

5

6

1

2

3

4

7

8

5

6

DVD-P370

DVD-P375

4

7

English

Rear Panel

1. SCART JACK

- Connect to a TV scart input jack.

2. DIGITAL AUDIO OUT JACKS

- Use either an optical or coaxial digital cable to con-

nect to a compatible Dolby Digital receiver.

- Use either an optical or coaxial digital cable to con-

nect to an A/V Amplifier that contains a Dolby Digital,

MPEG2 or DTS decoder.

3. COMPONENT VIDEO OUT JACKS

- Use these jacks if you have a TV with Component

Video in jacks. These jacks provide P

R

, P

B

and Y

video.

- If P-SCAN Video Output is selected in Setup Menu,

progressive scan mode will work.

- If I-SCAN Video Output is selected in Setup Menu,

interlaced scan mode will work.

4. AUDIO OUT JACKS

- Connect to the Audio input jacks of your television or

audio/video receiver.

5. VIDEO OUT JACK

- Use a video cable to connect to the Video input jack

on your television.

- The Video Output in Setup Menu must be set to

S-Video.

6. S-VIDEO OUT JACK

- Use the S-Video cable to connect this jack to the

S-Video jack on your television for higher picture

quality.

- The Video Output in Setup Menu must be set to

S-Video.

Note

- Consult your TV User’s Manual to find out if your TV supports Progressive Scan.

If Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in

the TV’s menu system.

- If P-SCAN Video Output is selected in Setup Menu, S-Video will not work.

- See pages 27 to get more information on how to use the setup menu.

2

1

3

4526

8

Tour of the Remote Control

1

2

3

4

5

6

7

8

9

10

14

11

12

13

15

16

17

18

19

20

21

22

23

5. INSTANT REPLAY Button

This function is used to replay the previous 10 seconds

of a movie from the current position.

6. SKIP Buttons (

/

)

Use to skip the title, chapter or track.

7. STOP Button ( )

8. MENU Button

Brings up the DVD player’s menu.

9. ENTER/



/



,

¥¥

/



Buttons

This button functions as a toggle switch.

10. EZ VIEW Button

The aspect ratio of a picture can easily be adjusted

according to the screen size of your TV (16:9 or 4:3).

11. DISC MENU Button

Brings up the Disc menu.

12. SUBTITLE Button

13. AUDIO Button

Use this button to access various audio functions on a disc.

14. ZOOM Button

Enlarge DVD Picture

15. OPEN/CLOSE ( ) Button

To open and close the disc tray.

16. STEP Button

Advances play one frame at a time.

17. INSTANT SKIP Button

This function skips playback ahead 10 seconds.

18. PLAY/PAUSE Button ( )

Begin/Pause disc play.

19. RETURN Button

Returns to a previous menu.

20. INFO Button

Displays the current disc mode.

21. CANCEL Button

Use to remove menus or status displays from the

screen.

22. REPEAT A-B Button

Allows you to repeat A-B disc.

23. REPEAT Button

Allows you to repeat play a title, chapter, track, or disc.

1. DVD POWER Button

Turns the power on or off.

2. NUMBER Buttons

3. VIDEO SEL. Button

Selects video output formats

4. SEARCH Buttos (

/

)

Allow you to search forward/backward through a disc.

9

CONNECTIONS

English

The following shows examples of connections commonly used to connect the DVD player with a TV and

other components.

Before Connecting the DVD Player

- Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.

- Refer to the user’s manual of the additional components you are connecting for more information on those

particular components.

Connecting to a TV (SCART)

- Using the SCART, connect the SCART (EXT) terminal on the rear of the DVD Player to the SCART (IN)

terminal of your TV.

- If your TV is not equipped with a SCART you can select one of the following alternative connections:

Connecting to a TV (VIDEO CVBS)

1

Using video/audio cables, connect the VIDEO

(yellow)/AUDIO (red and white) OUT terminals on the rear

of the DVD player to the VIDEO (yellow)/AUDIO (red and

white) IN terminals of TV.

2

Turn on the DVD player and TV.

3

Press the input selector on your TV remote control until the

Video signal from the DVD player appears on the TV

screen.

Note

- Noise may be generated if the audio cable is too close to the power cable.

- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 13 to 14)

- The number and position of terminals can vary depending on your TV set.

Please refer to the user's manual of the TV.

- If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) terminal of the

DVD player.

- Please do not connect Scart and Component Video (Y, Pb, Pr) output simultaneously, as they may inter-

fere and degrade both video output quality.

Choosing a Connection

RED

WHITE

YELLOW

RED

WHITE

YELLOW

Audio

Cable

SCART

Cable

Video

Cable

OR

10

Connection to a TV (S-Video)

- Connecting to your TV using an S-Video cable.

- You will enjoy high quality images. S-Video separates the picture element into black and white(Y) and

color(C) signals to present clearer images than regular video input mode. (Audio signals aredelivered

through the audio output.)

1

Using an S-Video cable (not included), connect the S-

VIDEO OUT terminal on the rear of the DVD player to the

S-VIDEO IN terminal of TV.

2

Using the audio cables, connect the AUDIO (red and

white) OUT terminals on the rear of the DVD player to the

AUDIO (red and white) IN terminals of TV. Turn on the

DVD player and TV.

3

Press the input selector on your TV remote control until the

S-Video signal from the DVD player appears on your TV

screen.

4

Set the Video Output to S-Video in the Display Setup

menu. (See pages 27)

Note

- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 13 to 14)

- The number and position of terminals can vary depending on the TV set.

Please refer to the user's manual of the TV.

- Please do not connect S-Video and Component Video (Y, Pb, Pr) output simultaneously, as they may

interfere and degrade both video output quality.

RED

WHITE

RED

WHITE

Audio Cable

S-Video Cable

(not included)

11

English

Connection to a TV (Interlace)

- Connecting to your TV using Component video cables.

- You will enjoy high quality and accurate color reproduction images. Component video separates the pic-

ture element into black and white(Y), blue(P

B

), red(P

R

) signals to present clear and clean images. (Audio

signals are delivered through the audio output.)

1

Using component video cables (not included), connect the

COMPONENT VIDEO OUT terminal on the rear of the

DVD player to the COMPONENT IN terminal of TV.

2

Using the audio cables, connect the AUDIO (red and

white) OUT terminals on the rear of the DVD player to the

AUDIO (red and white) IN terminals of TV. Turn on the

DVD player and TV.

3

Press the input selector on your TV remote control until the

Component signal from the DVD player appears on the TV

screen.

4

Set the Video Output to I-SCAN in the Display Setup

menu. (See pages 27)

Note

- If Video output is incorrectly set to S-Video, with the Component cables connected, the screen will

turn red.

- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 13 to 14)

- The component terminal of TV can be marked by “R-Y, B-Y, Y” or “Cr, Cb, Y” instead of “P

R

, P

B

, Y”

depending on the manufacturer. The number and position of terminals can vary depending on the TV set.

Please refer to the user's manual of the TV.

RED

WHITE

RED WHITE

RED

BLUE

GREEN

RED

BLUE

GREEN

Audio Cable

Component cable

(not included)

12

Connection to a TV (Progressive)

1

Using component video cables (not included), connect the

COMPONENT VIDEO OUT terminal on the rear of the

DVD player to the COMPONENT IN terminal of TV.

2

Using the audio cables, connect the AUDIO (red and

white) OUT terminals on the rear of the DVD player to the

AUDIO (red and white) IN terminals of TV. Turn on the

DVD player and TV.

3

Press the input selector on your TV remote control until the

Component signal from the DVD player appears on the TV

screen.

4

Set the Video Output to P-SCAN in the Display Setup

menu. (See pages 27)

To see the progressive video output,

You need a TV set supporting the progressive scan

input function. And you have to set up the TV

- Consult your TV User’s Manual to find out if your TV supports Progressive Scan. If Progressive

Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in the TV’s

menu system.

- Depending on your TV, the connection method may differ from the illustration above.

Note

- What is "Progressive Scan"?

Progressive scan has twice as many scanning lines as the interlace output method has. Progressive

scanning method can provide better and clearer picture quality.

RED

WHITE

RED

WHITE

RED

BLUE

GREEN

RED

BLUE

GREEN

Audio Cable

Component cable

(not included)

13

English

Connection to an Audio System (2 Channel Amplifier)

1

Using the audio cables, connect the AUDIO (red and

white) OUT terminals on the rear of the DVD player to the

AUDIO (red and white) IN terminals of the Amplifier.

2

Using the video signal cable(s), connect the VIDEO, S-

VIDEO or COMPONENT OUT terminals on the rear of the

DVD player to the VIDEO, S-VIDEO or COMPONENT IN

terminal of your TV as described on pages 9 to 12.

3

Turn on the DVD player, TV, and Amplifier.

4

Press the input select button of the Amplifier to select

external input in order to hear sound from the DVD player.

Refer to your Amplifier's user manual to set the Amplifier's

audio input.

Note

- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause

damage to the speakers and your ears.

- Please set the audio in the menu screen according to the Amplifier. (See pages 26)

- The position of terminals can vary depending on the Amplifier.

Please refer to the user's manual of the Amplifier.

RED

WHITE

RED

WHITE

Audio Cable

14

Connection to an Audio System (Dolby digital, MPEG2 or DTS Amplifier)

1

If using an optical cable (not included), connect the DIGI-

TAL AUDIO OUT (OPTICAL) terminal on the rear of the

DVD player to the DIGITAL AUDIO IN (OPTICAL) terminal

of the Amplifier.

If using a coaxial cable (not included), connect the DIGI-

TAL AUDIO OUT (COAXIAL) terminal on the rear of the

DVD player to the DIGITAL AUDIO IN (COAXIAL) termi-

nal of the Amplifier.

2

Using the video signal cable(s), connect the VIDEO, S-

VIDEO or COMPONENT OUT terminals on the rear of the

DVD player to the VIDEO, S-VIDEO or COMPONENT IN

terminal of your TV as described on pages 9 to 12

3

Turn on the DVD player, TV, and Amplifier.

4

Press the input select button of the Amplifier to select

external input in order to hear sound from the DVD player.

Refer to your Amplifier's user manual to set the Amplifier's

audio input.

Note

- When you connect the DVD player to DTS Amplifier and play a DTS disc, set the DTS to On in

Audio Setup menu. If it is set to Off, sound doesn't come out or there will be a big noise.

- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause

damage to the speakers and your ears.

- Please set the audio in the menu screen according to the Amplifier. (See pages 26)

- The position of terminals can vary depending on the Amplifier.

Please refer to the user's manual of the Amplifier.

- Please remove the dust cover before using the optical cable (not included) and put the cover on the cable

again when it's not used.

Optical Cable

(not included)

Coaxial Cable

(not included)

or

Dolby digital or

DTS amp

15

English

BASIC

FUNCTIONS

Playing a Disc

Before Play

- Turn on your TV and set it to the correct Video

Input by pressing TV/VIDEO button on the TV

remote control.

- If you connected an external Audio System, turn

on your Audio System and set it to the correct

Audio Input.

After plugging in the player, the first time you press the DVD

POWER button, this screen comes up: If you want to select

a language, press a NUMBER button. (This screen will only

appear when you plug in the player for the first time.)

If the language for the startup screen is not set, the settings

may change whenever you turn the power on or off.

Therefore, make sure that you select the language you want

to use.

Once you select a menu language, you can change it by

pressing the button on the front panel of the unit for

more than 5 seconds with no disc in the unit. Then the

SELECT MENU LANGUAGE window appears again where

you can reset your preferred language.

Playback

1. Press the OPEN/CLOSE ( ) button. The STANDBY

indicator light goes out and the tray opens.

2. Place a disc gently into the tray with the disc’s label facing

up.

3. Press the PLAY/PAUSE ( ) button or OPEN/ CLOSE

()button to close the disc tray.

-

When you stop disc play, the player remembers

where you stopped, so when you press

PLAY/PAUSE ( ) button again, it will pick up where

you left off.

4. Stopping Play

Press the STOP ( ) button during play.

6. Pausing Play

Press the PLAY/PAUSE ( ) or STEP button on the

remote control during play.

- Screen stops, no sound.

To resume, press the PLAY/PAUSE ( )

button once again.

7. Step Motion Play (Except CD)

Press the STEP button on the remote control during play.

- Each time the button is pressed, a new frame will

appear.

- No sound is heard during STEP mode.

- Press the PLAY/PAUSE ( ) button to resume

normal play.

- You can only perform step motion play in the

forward direction.

8. Slow Motion Play

Press the SEARCH (

/

) button to choose the play

speed between 1/8, 1/4 and 1/2 of normal during PAUSE

or STEP mode.

- No sound is heard during slow mode.

- Press the PLAY/PAUSE ( ) button to resume

normal play.

5. Removing Disc

Press the OPEN/CLOSE ( ) button.

Note

- If the player is left in the stop mode for more

than one minute without any user interaction, a

screen saver will be activated. Press the

PLAY/PAUSE ( ) button to resume normal play.

- If the player is left in the stop mode for more than

about 30 minutes, the power will automatically

shut off. (Automatic Power-Off Function)

- If the player is left for about 5 minutes in pause

mode, it will stop.

- This ( ) icon indicates an invalid button press.

Press 1 for English

Touche 2 pour Français

Drücken Sie 3 für Deutsch

Pulsar 4 para Español

Premere 5 per Italiano

Druk op 6 voor Nederlands

16

Using the Search and Skip

Functions

During play, you can search quickly through a chapter or

track, and use the skip function to jump to the next selection.

Searching through a Chapter or

Track

During play, press the SEARCH ( or ) button on the

remote control for more than 1 second.

Note

- The speed marked in this function may be

different from the actual playback speed.

- No sound is hearing during search mode

(Except CD).

DVD

CD

2X, 4X, 64X, 128X

2X, 4X, 8X

Skipping Tracks

During play, press the SKIP ( or ) button.

- When playing a DVD, if you press the SKIP ( ) button, it

moves to the next chapter. If you press the SKIP ( )

button, it moves to the beginning of the chapter. One more

press makes it move to the beginning of the previous

chapter.

- When playing a CD, if you press the SKIP ( ) button, it

moves to the next track. If you press the SKIP ( ) but

ton, it moves to the beginning of the track. One more

press makes it move to the beginning of the previous

track.

Using the Display Function

When Playing a DVD/MPEG4

1. During play, press the INFO button on the remote control.

2. Press the /buttons to select the desired item.

3. Press the ¦/ buttons to make the desired setup and then

press the ENTER button.

- You may use the number buttons of the remote control

to directly access a title, chapter or to start the play

back from a desired time.

Note

To access the desired title when there is

more than one in the disc. For example, if

there is more than one movie on a DVD,

each movie will be identified.

Most DVD discs are recorded in chapters so

that you can quickly find a specific passage.

Allows playback of the film from a desired

time. You must enter the starting time as a

reference.The time search function does not

operate on some disc.

Refers to the language of the film soundtrack.

In the example, the soundtrack is played in

English 5.1CH. A DVD disc can have up to

eight different soundtracks.

Refers to the subtitle languages available in

the disc. You will be able to choose the

subtitle languages or, if you prefer, turn them

off from the screen. A DVD disc can have up

to 32 different subtitles.

To access the desired Bookmark or Angle

function.

Some DVD dics are have more angle func-

tion from any picture.

Bookmark function make you easily and

quickly to find a track or chapter from DVD.

Title

Chapter

Time

Audio

Subtitle

4. To make the screen disappear, press the CANCEL button.

Shortcut

17

English

Using the Disc Menu

1. During stop mode of a DVD disc, press the MENU button

on the remote control.

2. Press the / buttons to select Disc Menu, then press the

 or ENTER button.

Note

- Depending on a disc, the Disc Menu may not

work.

- You can also use the Disc Menu, using the

DISC MENU button on the remote control.

Using the Title Menu

1. During the playback of a DVD disc, press the MENU button

on the remote control.

2. Press the / buttons to select Title Menu, then press the

 or ENTER button.

Note

- Depending on a disc, the Title Menu may not

work.

- Title Menu will only be displayed if there are at

least two titles in the disc.

Repeat the current track, chapter, title, a chosen

section (A-B), or all of the disc.

When playing a DVD

1. Press the REPEAT button on the remote control.

Repeat screen appears.

2. Press the ¦/ buttons to select Chapter, Title or A-B,

then press the ENTER button.

- DVD repeats play by chapter or title.

- Chapter ( ): repeats the chapter that is playing.

- Title ( ): repeats the title that is playing.

- A-B: repeats a segment of the disc that you select.

T

Off 01 01 A - B

REPEAT

ENTER

T

DVD

Press ENTER key

for Disc Menu

Press ENTER key

for Title Menu

Using the Disc and Title

Menu

Repeat Play

Using the A-B Repeat function

1. Press the REPEAT A-B button at the point where you

want repeat play to start (A). B is automatically highlighted.

2. Press the REPEAT A-B button at the point where you

want the repeat play to stop (B).

- To return to normal play, press the CANCEL button.

3. To return to normal play, press REPEAT button again, then

press the ¦/ buttons to select Off and press ENTER

button.

Off 01 01 A - B

REPEAT

ENTER

T

DVD

Note

- A-B REPEAT allows you to set point (B) until at

least 5 seconds of play back time has elapsed

after point(A) has been set.

- Depending on a disc, the Repeat function may

not work.

18

This feature allows you slowly to repeat scenes con-

taining sports, dancing, musical instruments being

played etc., so you can study them more closely.

When playing a DVD

1. During play, press the PLAY/PAUSE ( ) button.

2. Press the SEARCH (

/

) button to choose the play

speed between 1/8, 1/4 and 1/2 of normal during PAUSE or

STEP mode.

Slow Play

ADV

ANCED

FUNCTIONS

Adjusting the Aspect Ratio

(EZ View)

To play back using aspect ratio

(DVD)

Press the EZ VIEW button.

- The screen size changes when the button is pressed

repeatedly.

- The screen zoom mode operates differently depending on the

screen setting in the Display Setup menu.

- To ensure correct operation of the EZ VIEW button, you

should set the correct aspect ratio in the Display Setup

menu. (See pages 27).

If you are using a 16:9 TV

For 16:9 aspect ratio discs

- WIDE SCREEN

Displays the content of the DVD title in 16:9 aspect ratio.

- SCREEN FIT

The top and bottom portions of the screen are cut off.

When playing a 2.35:1 aspect ratio disc, the black bars at

the top and bottom of the screen will disappear. The picture

will look vertically stretched. (Depending on a type of disc,

the black bars may not disappear completely.)

- ZOOM FIT

The top, bottom, left and right of the screen are cut off and

the central portion of the screen is enlarge

For 4:3 aspect ratio discs

- Normal Wide

Displays the content of the DVD title in 16:9 aspect ratio.

The picture will look horizontally stretched.

- SCREEN FIT

The top and bottom portions of the screen are cut off and

the full screen appears.

The picture will look vertically stretched.

- ZOOM FIT

The top, bottom, left and right portions of the screen are

cut off and the central portion of the screen is enlarged.

- Vertical Fit

When a 4:3 DVD is viewed on a 16:9 TV, black bars will

appear at the left and right of the screen in order to prevent

the picture from looking horizontally stretched.

EZ VIEW

WIDE SCREEN

19

English

If you are using a 4:3 TV

For 16:9 aspect ratio discs

- 4:3 Letter Box

Displays the content of the DVD title in 16:9 aspect ratio. The

black bars will appear at the top and bottom of the screen.

- 4:3 Pan Scan

The left and right portions of the screen are cut off and the

central portion of the 16:9 screen is displayed.

- SCREEN FIT

The top and bottom portions of the screen are cut off and a

full screen appears. The picture will look vertically stretched.

- ZOOM FIT

The top, bottom, left and right of the screen are cut off and

the central portion of the screen is enlarged.

For 4:3 aspect ratio discs

- Normal Screen

Displays the content of the DVD title in 4:3 aspect ratio.

- SCREEN FIT

The top and bottom portions of the screen are cut off and the

full screen appears. The picture will look vertically stretched.

- ZOOM FIT

The top, bottom, left and right portions of the screen are cut

off and the central portion of the screen is enlarged.

Note

This function may behave differently depending on

the type of disc.

Selecting the Audio

Language

You can select a desired audio language quickly and

easily with the AUDIO button.

Using the AUDIO button

(DVD/MPEG4)

1. Press the AUDIO button. The Audio changes when the

button is pressed repeatedly.

The audio languages are

represented by

abbreviations.

2. To remove the AUDIO icon, press the CANCEL or RETURN

button.

ENG

DOLBY DIGITAL 5.1CH

AUDIO

DVD

Note

- This function depends on audio languages are

encoded on the disc and may not work.

- A DVD disc can contain up to 8 audio lan-

guages.

- To have the same audio language come up

whenever you play a DVD;

Refer to “Using the Audio Language” on page 25.

Selecting the Subtitle

Language

You can select a desired subtitle quickly and

easily with the SUBTITLE button.

Using the SUBTITLE button

(DVD/MPEG4)

1. Press the SUBTITLE button. The subtitle languages are

represented by abbreviations.

The subtitle changes when

the button is pressed

repeatedly.

2. To remove the SUBTITLE icon, press the CANCEL or

RETURN button.

Note

- You have to change the desired subtitle in the

Disc Menu, according to discs. Press the DISC

MENU button.

- This function depends on what subtitles are

encoded on the disc and may not work on all DVDs.

- A DVD disc can contain up to 32 subtitle

languages.

- To have the same subtitle language come up

whenever you play a DVD; Refer to “Using the

Subtitle Language” on page 25.

DVD

Off

SUBTITLE

Press Audio button at

remocon repeatedly to

select the desired Audio

on MPEG4 then press

the ENTER .

AUDIO

MPEG4

PCM 1/2

Press SUBTITLE button at

remocon repeatedly to

select the desired subti-

tle language on a

MPEG4 then press the

ENTER .

SUBTITLE

MPEG4

Off

External Subtitle option

will appear, depends on

the DivX disc.

ReturnEnter

Subtitle Selection

External Subtitle Off

readme.TXT

Non-standard fonts are not supported

Menu

MPEG4

20

Changing the Camera

Angle

When a DVD contains multiple angles of a particular

scene, you can use the ANGLE function.

Using the ANGLE button (DVD)

If the disc contains multiple angles, the ANGLE

appears on the screen.

1. During play, press the INFO button on the remote control.

2. Press the / buttons to select Shortcut.

3. Press the

¦/

buttons to select Angle, then press the

ENTER button.

Note

Depending on the disc, these functions may not

work.

4/6

Using the Instant

Replay/Skip Function

Using the Instant Replay function

(DVD)

If you miss a scene, you can see it again using this

function.

If you press the INSTANT REPLAY button, the current scene

moves backward about 10 seconds, and plays back.

Using the Instant Skip function

(DVD)

Use this function to skip playback about 10 seconds

ahead of the current scene.

Press the INSTANT SKIP button.

- Playback will skip ahead 10 seconds.

Using the Bookmark

Function

This feature lets you bookmark sections of a DVD

so you can quickly find them at a later time.

Using the Bookmark Function

(DVD)

1. During play, press the INFO button on the remote control.

2. Press the / buttons to select Shortcut, then press the

ENTER button.

4. When you reach the scene you want to mark, press the

ENTER button. Up to three scenes may be marked at a time.

1 - -

Note

- Depending on a disc, the Bookmark function

may not work.

5. Press the PLAY/PAUSE ( ) button to skip to the marked

scene.

Recalling a Marked Scene

1~3. The first 1~3 steps are the same as those for “Using the

Bookmark Function” on page 20.

4. Press the

¦/

buttons to select a marked scene.

1 2 3

4. Press the

¦/

buttons or you can use the number buttons

on the remote control to select the desired angle.

Clearing a Bookmark

1~3. The first 1~3 steps are the same as those for “Using the

Bookmark Function” on page 20.

4. Press the

¦/

buttons to select the bookmark number you

want to delete.

Note

- If the disc has only one angle, this feature won’t

work. Currently, very few discs have this feature.

- Depending on the disc, these functions may not

work.

3. Press the

¦/

buttons to select Bookmark, then press the

ENTER button.

DVD

La pagina sta caricando ...

Samsung DVD-P370 Manuale utente

Samsung DVD-P370 Manuale utente

Documenti correlati

Altri documenti