Haier 2HUM18R03/R2(DB) Istruzioni per l'uso

Marca: Haier

Modello: 2HUM18R03/R2(DB)

Categoria: Condizionatori d'aria a sistema split

Tipo: Istruzioni per l'uso

SPLIT TYPE ROOM AIR CONDITIONER

OPERATION MANUAL

Please read this operation manual before using the air conditioner.

No.00105

HSM09HA03/R2(DB)

HSM12HA03/R2(DB)

2HUM18R03/R2(DB)

Tutti i prodotti sono conformi alle seguenti normative europee:

- Direttiva 73/23/EEC Basso Voltaggio

- Direttiva 2006/95/EC Basso Voltaggio

- Direttiva 89/336/EEC Compatibilità elettromagnetica

- Direttiva 2004/108/EC Compatibilità elettromagnetica

ROHS

Il prodotto è conforme alla normativa 2002/95/EEC sulla restrizione d’uso di

sostanze inquinanti negli apparecchi elettrici ed elettronici.

WEEE

Informativa al consumatore come previsto dalla normativa europea

2002/96/CE riguardante i rifiuti di apparecchiature elettriche ed elettroniche.

SPECIFICHE DI SMALTIMENTO:

Il climatizzatore è contrassegnato con questo simbolo,

ciò significa che i prodotti elettrici ed elettronici non

possono essere smaltiti insieme ai rifiuti domestici non

differenziati. Non cercare di demolire il sistema da soli:

la demolizioni dei sistemi di condizionamento, nonché il

recupero del refrigerante, dell’olio e di qualsiasi altra

parte devono essere eseguiti da un installatore qualifi-

cato in conformità alla legislazione locale e nazionale

vigente in materia.I climatizzatori devo essere trattati presso una struttura spe-

cializzata nel riutilizzo, riciclaggio e recupero dei materiali. Il corretto smaltimen-

to del prodotto eviterà le possibili conseguenze negative all’ambiente e alla

salute dell’uomo. Per maggiori informazioni contattare l’installatore o le autori-

tà locali. Le batterie devono essere tolte dal telecomando e smaltite separata-

mente conformemente alla legislazione locale e nazionale vigente in materia.

CONFORMITÀ ALLE DIRETTIVE EUROPEE PER I MODELLI:

Haier Industrial Park, No.1 Haier Road, Qingdao, P.R.China

All the products are in conformity with the following European provision:

- Low Voltage Directive 73/23/EEC

- Low Voltage Directive 2006/95/EC

- Electromagnetic CompatibilitY 89/336/EEC

- Electromagnetic CompatibilitY 2004/108/EC

ROHS

The products are fulfilled with the requirements in the directive 2002/95/EEC of the

European parliament and of the council on the Restriction of the use of Certain Haz-

ardous Substances in Electrical and Electronic Equipment (EU RoHS Directive)

WEEE

In accordance with the directive 2002/96/CE of the European parliament,

herewith we inform the consumer about the disposal requirements of the

electrical and electronic products.

DISPOSAL REQUIREMENTS:

Your air conditioning product is marked with this sym-

bol. This means that electrical and electronic products

shall not be mixed with unsorted household waste.

Do not try to dismantle the system yourself: the dis-

mantling of the air conditioning system, treatment of

the refrigerant, of oil and of other part must be done

by a qualified installer in accordance with relevant

local and national legislation. Air conditioners must be

treated at a specialized treatment facility for re-use, recycling and recovery.

By ensuring this product is disposed of correctly, you will help to prevent

potential negative consequences for the environment and human health.

Please contact the installer or local authority for more information. Battery

must be removed from the remote controller and disposed of separately in

accordance with relevant local and national legislation.

EUROPEAN REGULATIONS CONFORMITY FOR THE MODELS:

Tous les produits sont conformes aux directives européennes suivantes:

- Directive 73/23/CEE Basse tension

- Directive 2006/95/CE Basse tension

- Directive 89/336/CEE Compatibilité électromagnétique

- Directive 2004/108/CE Compatibilité électromagnétique

ROHS

L'appareil est conforme à la directive 2002/95/CEE relative à la limitation de

l'utilisation de certains substances dangereuses dans les équipements élec-

triques et électroniques.

DEEE (WEEE)

Information au consommateur comme le prévoit la directive européenne

2002/96/CE relative aux déchets d'équipements électriques et électro-

niques.

SPECIFICATIONS POUR L'ELIMINATION:

Ce pictogramme, apposé sur le climatiseur, signifie

que les équipements électriques et électroniques ne

peuvent pas être éliminés avec les déchets ménagers

non triés. Ne pas essayer de démanteler l'équipement

soi-même: le démantèlement des systèmes de clima-

tisation, ainsi que la récupération du frigorigène, de

l'huile et de toute autre partie doivent être effectués

par un installateur qualifié conformément à la législa-

tion locale et nationale en vigueur en la matière. Les climatiseurs doivent être

traités dans un centre spécialisé dans la réutilisation, le recyclage et la valo-

risation des matériaux. L'élimination correcte de ces appareils permet d'évi-

ter les effets nocifs sur l'environnement et la santé humaine. Pour plus de

renseignements contacter l'installateur ou les autorités locales. Les piles doi-

vent être retirées de la télécommande et éliminées séparément, conformé-

ment à la législation locale et nationale en vigueur en la matière.

CONFORMITÉ AUX DIRECTIVES EUROPÉENNES POUR LES MODÈLES:

Haier Industrial Park, No.1 Haier Road, Qingdao, P.R.China

Todos los productos están en conformidad con las siguientes Normativas

Europeas:

- Bajo Voltaje directiva 73/23/EEC

- Bajo Voltaje directiva 2006/95/EC

- Compatibilidad electromagnética 89/336/EEC

- Compatibilidad electromagnética 2004/108/EC

ROHS

Los productos cumplen los requisitos de la directiva 2002/95/EEC del parla-

mento Europeo y el consejo regulador Del uso de materiales peligrosos en

equipamientos eléctricos Y electrónicos. (EU RoHS Directiva).

WEEE

De acuerdo con la directiva 2002/96/CE del parlamento Europeo, Informa-

mos al consumidor acerca del reciclage de los productos Electrónicos y

eléctricos.

REQUISITOS PARA LA ELIMINACIÓN:

Su acondicionador de aire está marcado con este

símbolo. Esto significa que los productos eléctricos y

electrónicos no deben mezclarse con el resto de resi-

duos domésticos no clasificados.

No intente desmontar el sistema usted mismo: El des-

mantelamiento del acondicionador de aire, así como

el tratamiento del refrigerante, aceite y otros compo-

nentes, debe ser efectuado por un instalador compe-

tente de acuerdo con las normas locales y nacionales aplicables. Los acon-

dicionadores de aire deben ser tratados en instalaciones especializadas para

su reutilización, reciclaje y recuperación. Al asegurarse de desechar este pro-

ducto de la forma correcta, està contribuyendo a evitar posibles consecuen-

cias negativas para el entorno y para la salud de las personas. Contacte, por

favor, con el instalador o con las autoridades locales para obtener más infor-

mación. Las pilas del control remoto deben extraerse y eliminarse por sepa-

rado y de acuerdo con la normativa local y nacional aplicable.

CONFORMIDAD EUROPEA DE LAS REGULACIONES PARA LOS MODELOS:

Questo prodotto contiene gas fluorurati ad effetto serra inclusi nel Protocollo

di Kyoto. Non liberare tali gas nell’atmosfera.

Tipo di refrigerante: R410A

Valore GWP*: 1975

GWP = potenziale di riscaldamento globale

Compilare con inchiostro indelebile,

• 1 la carica di refrigerante di fabbrica del prodotto

• 2 la quantità di refrigerante aggiuntiva nel campo e

• 1+2 la carica di refrigerante totale

sull’etichetta di carica del refrigerante fornita con il prodotto

L’etichetta compilata deve essere collocata in prossimità della portata di cari-

ca del prodotto (ad esempio, nell’interno del coperchio della valvola d’inter-

cettazione).

A contiene gas fluorurati ad effetto serra inclusi nel protocollo di Kyoto

B carica di refrigerante di fabbrica del prodotto: vedi targhetta con il nome

dell’unità

C quantità di refrigerante aggiuntiva nel campo

D carica di refrigerante totale

E unità esterna

F cilindro del refrigerante e collettore di carica

INFORMAZIONI IMPORTANTI SUL REFRIGERANTE UTILIZZATO

Haier Industrial Park, No.1 Haier Road, Qingdao, P.R.China

1+2=

R410A

Contains fluorinated greenhouse gases

covered by the Kyoto Protocol

This product contains fluorinated greenhouse gases covered by the Kyoto

Protocol. Do not vent into the atmosphere.

Refrigerant type: R410A

GWP* value: 1975

GWP = global warming potential

Please fill in with indelible ink,

• 1 the factory refrigerant charge of the product

• 2 the additional refrigerant amount charged in the field and

• 1+2 the total refrigerant charge

on the refrigerant charge label supplied with the product.

The filled out label must be adhered in the proximity of the product charging

port (e.g. onto the inside of the stop valve cover).

A contains fluorinated greenhouse gases covered by the Kyoto Protocol

B factory refrigerant charge of the product: see unit name plate

C additional refrigerant amount charged in the field

D total refrigerant charge

E outdoor unit

F refrigerant cylinder and manifold for charging

IMPORTANT INFORMATION REGARDING THE REFRIGERANT USED

Ce produit contient des gaz à effet de serre fluorés encadrés par le protoco-

le de Kyoto. Ne pas laisser les gaz s’échapper dans l’atmosphère.

Type de réfrigérant: R410A

Valeur GWP*: 1975

GWP = potentiel de réchauffement global

Prière de compléter à l’encre indélébile,

• 1 la charge de réfrigérant d’usine du produit

• 2 la quantité de réfrigérant supplémentaire chargée sur place et

• 1+2 la charge de réfrigérant totale

sur l’étiquette de charge de réfrigérant fournie avec le produit.

L’étiquette complétée doit être apposée à proximité de l’orifice de recharge

du produit (par ex. à l’intérieur du couvercle de la vanne d’arrêt).

A contient des gaz à effet de serre fluorés encadrés par le protocole de

Kyoto

B charge de réfrigérant d’usine du produit: voir plaquette signalétique de

l’unité

C quantité de réfrigérant supplémentaire chargée sur place

D charge de réfrigérant totale

E unité extérieure

F cylindre de réfrigérant et collecteur de recharge

INFORMATION IMPORTANTE RELATIVE AU RÉFRIGÉRANT UTILISÉ

Haier Industrial Park, No.1 Haier Road, Qingdao, P.R.China

1+2=

R410A

Contains fluorinated greenhouse gases

covered by the Kyoto Protocol

Este producto contiene los gases fluorados de efecto invernadora regulados

por el Protocolo de Kioto. No vierta gases a la atmósfera.

Tipo de refrigerante: R410A

Valor GWP*: 1975

GWP = Potencial de calentamiento global

Rellene con tinta indeleble,

• 1 la carga de refrigerante de fábrica del producto

• 2 la cantidad adicional de refrigerante cargado en campo y

• 1+2 la carga total de refrigerante

En la etiqueta de carga de refrigerante suministrada con el producto.

La etiqueta rellenada debe pegarse cerca de la conexión de carga del pro-

ducto (p.ej. en el interior de la cubierta de la válvula de tope).

A Contiene los gases fluorados de efecto invernadora regulados por el

Protocolo de Kioto

B Carga de refrigerante de fábrica del producto: véase placa de especifi-

caciones técnicas de la unidad

C Cantidad adicional de refrigerante cargado en campo

D Carga total de refrigerante

E Unidad exterior

F Cilindro del refrigerante y dosificador de carga

INFORMACIÓN IMPORTANTE EN RELACIÓN AL REFRIGERANTE UTILIZADO

Before disposing an old air conditioner that

goes out of use, please make sure it's inop-

erative and safe. Unplug the air conditioner

in order to avoid the risk of child entrapment.

It must be noticed that air conditioner system

contains refrigerants, which require speciali-

zed waste disposal. The valuable materials

contained in an air conditioner can be recycled

.Contact your local waste disposal center for

proper disposal of an old air conditioner and

contact your local authority or your dealer if

you have any question. Please ensure that

the pipework of your air conditioner does not

get damagedprior to being picked up by the

relevant waste disposal center, and contribute

to environmental awareness by insisting on an

appropriate, anti-pollution method of disposal.

Cautions

Disposal of the old air conditioner

All the packaging materials employed in the

package of your new air conditioner may be

disposed without any danger to the

environment.

The cardboard box may be broken or cut into

smaller pieces and given to a waste paper

disposal service. The wrapping bag made of

polyethylene and the polyethylene foam pads

All these valuable materials may be taken to

a waste collecting center and used again after

adequate recycling.

Consult your local authorities for the name

and address of the waste materials collecting

centers and waste paper disposal services

nearest to your house.

Disposal of the packaging of your

new air conditioner

Before starting the air conditioner, read the

information given in the User's Guide caref-

ully. The User's Guide contains very impor-

tant observations relating to the assembly,

operation and maintenance of the air

conditioner.

The manufacturer does not accept respon-

sibility for any damages that may arise due

to non-observation of the following

instruction.

Damaged air conditioners are not to be

put into operation. In case of doubt, consult

your supplier.

Use of the air conditioner is to be carried

out in strict compliance with the relative

instructions set forth in the User's Guide.

Installation shall be done by professional

people, don't install unit by yourself.

For the purpose of the safety,the air con-

ditioner must be properly grounded in acco-

rdance with specifications.

Always remember to unplug the air

conditioner before openning inlet grill. Never

unplug your air conditioner by pulling on

the power cord. Always grip plug firmly and

pull straight out from the outlet.

All electrical repairs must be carried out

by qualified electricians. Inadequate repairs

may result in a major source of danger for

the user of the air conditioner.

Safety Instructions and Warnings

Do not damage any parts of the air

conditioner that carry refrigerant by piercing

or performating the air conditioner's tubes

with sharp or pointed items, crushing or

twisting any tubes, or scraping the coatings

off the surfaces. If the refrigerant spurts

out and gets into eyes, it may result in

serious eye injuries.

Do not obstruct or cover the ventilation

grille of the air conditoner.Do not put fingers

or any other things into the inlet/outlet and

swing louver.

Do not allow children to play with the air

conditioner.In no case should children be

allowed to sit on the outdoor unit.

The refrigerating circuit is leak-proof.

1.Applicable ambient temperature range:

Specifications

The machine is adaptive in following

situation

11 .The power plug and connecting cable

must have acquired the local attestation.

2. If the power supply cord is damaged, it

must be replaced by the manufacturer

or its service agent or a similar qualified

person.

3. If the fuse of indoor unit on PC board is

broken,please change it with the type of

T. 3.15A/ 250V. If the fuse of outdoor

unit is broken,change it with the type of

T.25A/250V

4. The wiring method should be in line with

the local wiring standard.

5. After installation, the power plug should

be easily reached.

6. The waste battery should be disposed

properly.

7. The appliance is not intended for use

by young children or infirm persons

without supervision.

8. Young children should be supervised

to ensure that they do not play with

the appliance.

9.Please employ the proper power plug,

which fit into the power supply cord.

Cautions

Cooling

Indoor

Maximum:D.B/W.B

Maximum:D.B

Minimum:D.B/W.B

Maximum:D.B/W.B

Minimum:D.B/W.B

Outdoor

Indoor

Outdoor

Heating

C/23

C/18

-7

C/-8

C/26

C/14

12.In order to protect the units,please turn

off the A/C first, and at least 30 seconds

later, cutting off the power.

10. A breaker should be incorporated into

fixed wiring. The breaker should be

all-pole switch and the distance between

its two contacts should be not less than

3mm.

Cautions

STRICT

ENFORCEMENT

Safety Instruction

Installation

WARNING

Please read the following Safety Instructions carefully prior to use.

The instructions are classified into two levels, WARNING and CAUTION according to

the seriousness of possible risks and damages as follows. Compliance to the

instructions are strictly required for safety use.

Please call Sales/Service Shop for the Installation.

Do not attempt to install the air conditioner by yourself because improper works

may cause electric shock, fire, water leakage.

lnstallation in a inadequate place may cause accidents. Do not install in the following place.

Connect the earth

cable.

earthing

Do not install in the

place where there is

any possibility of

inflammable gas

leakage around the

unit.

Do not get the unit

exposed to vapor

or oil steam.

Check proper

installation of the

drainage securely

PROHIBITION PROHIBITION

CAUTION

Cautions

WARNING

When abnormality such as burnt-small found,

immediately stop the operation button and

contact sales shop.

OFF

Use an exclusive power source with a

circuit breaker

ENFORCEMENT

Connect power supply cord

to the outlet completely

Use the proper voltage

Do not use power supply cord

in a bundle.

Take care not to damage

the power supply cord.

Do not use power supply cord

extended or connected in halfway

STRICT

ENFORCEMENT

STRICT

ENFORCEMENT

PROHIBITION

Do not start or stop the

operation by disconnecting

the power supply cord and so on.

Do not channel the air flow directly

at people, especially at infants or

the aged.

Do not try to repair or reconstruct

by yourself.

Do not use for the purpose of storage of

food, art work, precise equipment,

breeding, or cultivation.

CAUTION

Take fresh air occasionally especially

when gas appliance is running at the

same time.

PROHIBITION

STRICT

ENFORCEMENT

Do not operate the switch with

wet hand.

PROHIBITION

Do not install the unit near a fireplace

or other heating apparatus.

Check good condition of the

installation stand

Do not pour water onto the unit

for cleaning

PROHIBITION

Do not place animals or plants in

the direct path of the air flow

Do not place any objects on or

climb on the unit.

Do not place flower vase or water

containers on the top of the unit.

Do not insert objects into the air

inlet or outlet.

PROHIBITION

Parts and Functions

Indoor unit

Outdoor unit

Inlet grille

Air filter

Vertical flap

Power indicator

Timer mode indicator

Operation mode indicator

Remote signal receiver

Emergency switch(manual)

Test running switch(manual)

Use remote controller to

adjust up and down air flow.

(Don't adjust it manually.)

Lights up when unit starts.

Lights up when Timer operation

is selected.

Lights up during compressor

running.

A beeping sound is generated when

a signal from remote controller is

received.

Used when remote controller is lost or

defective. Unit will run temporarily.

Used only for test running in cooling

when room temp. is below 16

Don't use it in normal operation.

OUTLET

CONNECTING PIPING AND ELECTRICAL WIRING

DRAIN HOSE

INLET

For multi-split type, the power plug is on the outdoor unit

Actual inlet grille may vary from the one shown in the manual according to the product purchased

16. SIGNAL SENDING display

17. POWER/SOFT display

18. Left/right air flow display

19. TEMP display

Remote controller: to display the TEMP. setting.

20. TIMER OFF display

21. CLOCK display

22. FAN button

Used to select fan speed: LOW,MED, HI, AUTO

23. ON/OFF button

Used for unit start and stop.

24. SLEEP button

Used to select sleep mode.

25. SET button

Used to confirm timer and clock settings.

26. POWER/SOFT button

27. LOCK

Used to lock buttons and LCD display. If

pressed, the other buttons will be disabled

and the lock condition display appears.

Press it once again, lock will be canceled

and lock condition display disappears.

28. CODE

Used to select CODE A or B with a press,A or

B will be displayed on LCD.

Please select A without special explanation.

1. SWING button

Used to select up or down air sending direction.

2. HOUR button

Used to set clock and timer setting.

3. MODE button

Used to select operation mode. AUTO,

COOL,DRY, FAN,HEAT.

4. HEALTH button

Used to set healthy operation.

5. CLOCK button

Used to set correct time.

6. TIMER button

Used to select TIMER ON,

TIMER OFF, TIMER ON-OFF.

7. RESET

When the remote controller appears

abnormal, use a sharp pointed article

to press this button to reset the

remote controller normal

11. LOCK display

12. FAN SPEED display

13. TIMER ON display

14. TEMP button

Used to select your desired temperature.

15. Operation mode display

LOW

Operation mode AUTO HEAT FANCOOL DRY

Remote controller

MED AUTO

Parts and Functions

10. SWING UP/DOWN display

NOTE: (1)The following functions and related displays are not available

(2) Cooling only unit do not have functions and displays related with heating.

8. HEALTH display

9. SLEEP display

Remove the batteries in case unit won't be in usage for a long period. If there are any display after

taking-out, just need to press reset key.

Parts and Functions

Clock Set

When unit is started for the first time and after replacing batteries in remote

controller, clock should be adjusted as follows:

Remote controller's operation

3. After time setting is confirmed, press SET, "AM" or "PM" stop flashing,

while clock starts working.

2. Press or to set correct time. Each press will increase or decrease 1

min. If the button is kept depressed, time will change quickly.

1. Press CLOCK button,"AM" or "PM" flashes.

When in use, put the signal transmission head directly to the receiver hole on the indoor unit.

The distance between the signal transmission head and the receiver hole should be within 7 m

without any obstacle as well.

Don't throw or knock the remoter controller.

When electronic-started type fluorescent lamp or change-over type fluorescent lamp or wireless

telephone is installed in the room, the receiver is apt to be disturbed in receiving the signals,

so the distance to the indoor unit should be shorter.

Loading of the battery

Load the batteries as illustrated right

2 R-03 (7#) batteries

Remove the battery cover:

Slightly press" "area and push down the cover

as illustrated.

Load the battery:

Be sure that the loading is in line with the "+" *"- ".

request as illustrated on the bottom of the case.

Put on the cover again.

Confirmation indicator:

After pressing power ON/OFF, if no display, reload the batteries.

Note:

Full display or unclear display during operation indicates the batteries have been used up.

Please change batteries.

Used two new same-typed batteries when loading.

If the remote controller can't run normally during operation, please remove the batteries and

reload several minutes later.

Hint:

Press HEALTH button, the health function stops.

The pilot light of healthy process on the display board

is extinguished.

BRIEF INTRODUCTION TO HEALTH OPERATION

The anion generator in the air conditioner can generate a lot of anion to

effectively balance the quantity of position and anion in the air and also to kill

bacteria and speed up the dust sediment in the room and finally clean the air

in the room.

Note

When the fan in the indoor unit does not work, the health lamp lights up, but

the anion generator does not release anion.

Operation

Health Operation

Remote controller

1. Unit start

Then set up the comfortable working state.

Link with electronic power.

Press ON/OFF on the remote controller, unit starts.

The liquid crystal will display the working state of last

time (Except Timer, Sleep, Power/Soft and Health

airflow).

2. Select operation mode

Press HEALTH button. For each press, is displayed.

hence healthy process begins.

When indoor wind machine is running, it has healthy

process function. (It's available under any mode)

3. Unit stop

Operation

Auto Operation

Remote controller

About Auto Operation

Under the mode of auto operation, air conditioner will

automatically select Cool or Heat operation according

to room temperature.

1. Unit start

Link with electronic power.

Press ON/OFF on the remote controller, unit starts.

The liquid crystal will display the working state of last

time (Except Timer, Sleep, Power/Soft and Health

airflow).

2.Select operation mode

Press MODE button. For each press, operation mode

changes as follows:

Remote controller:

Then Select Auto operation

AUTO COOL DRY FAN HEAT

Press FAN button. For each press, fan speed changes as

follows:

Remote controller:

Press TEMP. button

Every time the button is pressed, temp.setting

increase 1

C,if kept depressed, it will increase

rapidly

Every time the button is pressed, temp.setting

decrease 1

C,if kept depressed, it will decrease

rapidly

Select a desired temperature.

4.Fan speed selection

3.Select temp.setting

5.Unit stop

Air conditioner is running under displayed wind speed

When FAN is set to AUTO, the air conditioner

automatically adjusts the fan speed according to room

temperature.

Press ON/OFF button, the unit stops.

LOW

MED

AUTO

Operation

Cool Operation

Remote controller

1. Unit start

Link with electronic power.

Press ON/OFF on the remote controller, unit starts.

The liquid crystal will display the working state of last

time (Except Timer, Sleep, Power/Soft and Health

airflow).

2.Select operation mode

Press FAN button. For each press, fan speed changes as

follows:

Press MODE button. For each press, operation mode

changes as follows:

Remote controller:

Then Select COOL operation

Press TEMP. button

Every time the button is pressed, temp.setting

increase 1

C,if kept depressed, it will increase

rapidly

Every time the button is pressed, temp.setting

decrease 1

C,if kept depressed, it will decrease

rapidly

Select a desired temperature.

4.Fan speed selection

3.Select temp.setting

5.Unit stop

Air conditioner is running under displayed wind speed

When FAN is set to AUTO, the air conditioner

automatically adjusts the fan speed according to room

temperature.

Press ON/OFF button, the unit stops.

AUTO

LOW

MED

AUTO

COOL DRY FAN HEAT

Operation

Dry Operation

Remote controller

1. Unit start

Link with electronic power.

Press ON/OFF on the remote controller, unit starts.

The liquid crystal will display the working state of last

time (Except Timer, Sleep, Power/Soft and Health

airflow).

2.Select operation mode

Press FAN button. For each press, fan speed changes as

follows:

Press MODE button. For each press, operation mode

changes as follows:

Remote controller:

Then Select DRY operation

Press TEMP. button

Every time the button is pressed, temp.setting

increase 1

C,if kept depressed, it will increase

rapidly

Every time the button is pressed, temp.setting

decrease 1

C,if kept depressed, it will decrease

rapidly

Select a desired temperature.

4.Fan speed selection

3.Select temp.setting

5.Unit stop

Press ON/OFF button, the unit stops.

COOL operation starts when room

temp.is higher than temp.setting.

On reaching temp.setting +2

unit will run in mild DRY mode.

Ultra-low air flow

Temp.setting+2

Temp.setting

AUTO

LOW

MED

AUTO

COOL DRY FAN HEAT

Air conditioner is running under displayed fan speed.

In DRY mode, when room temperature becomes

lower than temp.setting+2

C,unit will run intermittently

at LOW speed regardless of FAN setting.

Operation

Fan Operation

Remote controller

1. Unit start

Link with electronic power.

Press ON/OFF on the remote controller, unit starts.

The liquid crystal will display the working state of last

time (Except Timer, Sleep, Power/Soft and Health

airflow).

2.Select operation mode

Press FAN button. For each press, fan speed changes as

follows:

Press MODE button. For each press, operation mode

changes as follows:

Remote controller:

Then Select FAN operation

3.Fan speed selection

4.Unit stop

About FAN operation

In FAN operation mode, the unit will not operate in

COOL or HEAT mode but only in FAN mode ,AUTO is

not available in FAN mode.And temp.setting is disabled.

In FAN mode,SLEEP operation is not available.

Press ON/OFF button, the unit stops.

AUTO

LOW

MED

COOL DRY FAN HEAT

Operation

Heat Operation

Remote controller

1. Unit start

Link with electronic power.

Press ON/OFF on the remote controller, unit starts.

The liquid crystal will display the working state of last

time (Except Timer, Sleep, Power/Soft and Health

airflow).

2.Select operation mode

Press FAN button. For each press, fan speed changes as

follows:

Press MODE button. For each press, operation mode

changes as follows:

Remote controller:

Then Select HEAT operation

Press TEMP. button

Every time the button is pressed, temp.setting

increase 1

C,if kept depressed, it will increase

rapidly.

Every time the button is pressed, temp.setting

decrease 1

C,if kept depressed, it will decrease

rapidly.

Select a desired temperature.

4.Fan speed selection

3.Select temp.setting

Air conditioner is running under displayed wind speed

IN HEAT mode, warm air will blow out after a short period

of the time due to cold-draft prevention function.

AUTO

LOW

MED

AUTO

COOL DRY FAN HEAT

When FAN is set to AUTO, the air conditioner

automatically adjusts the fan speed according to room

temperature.

Operation

(5)Air flow direction adjustment

After operation mode is selected, vertical flap will open automatically according to the mode.

Referring to the Fig.

COOL

HEAT

COOL

HEAT

About 10

About 60

About 10

About 45

About 60

better set a temp. difference of 3-5

C between indoor and outdoor temp. in COOL mode.

Hints

As cold air flows downward in COOL mode, adjusting air flow horizontally will be much more

helpful for a better air circulation.

As warm air flows upward in HEAT mode, adjusting air flow downward will be much more

helpful for a better air circulation.

Be careful not to catch a cold when cold air blows downward.

It is harmful to your health in summer to go frequently in and out of places where temp.

difference is above 7

C. Temp. difference of 3-5

C will remove your fatigue.

More than this, unit's load can be reduced and power consumption cut down as well. So, you'd

(6)Unit stop

Press ON/OFF button.

Only time remains on LCD.

All indicators on indoor unit go out.

Vertical flap closes automatically.

Cautions:

Unit won't restart until 3 minutes have

elapsed, due to system protection.

HEAT mode is not available on

cooling only unit.

It is advisable not to keep vertical flap at

downward position for a long time in COOL

or DRY mode, otherwise, condensate

water might occur.

Cautions:

When humidity is high, condensate water

might occur at air outlet if all horizontal

louvers are adjusted to left or right.

Move the horizontal blade by a knob on air

conditioner to adjust left and right direction

referring to Fig.

Left and right air flow adjustment

(manual)

Press SWING button, vertical flap will move within

the range shown in the Fig. Press SWING button

stop it at a fixed position.

Up and down (Use remote controller)

Before going to bed, you can simply press the

SLEEP button and unit will operate in SLEEP

mode and bring you a sound sleep.

Use of SLEEP function

After the unit starts, set the operation status,

then press SLEEP button before which the

clock must be adjusted and time being set.

Operation Mode

1. In COOL,DRY mode

1 hours after SLEEP mode starts, temp. will

become 1

C higher than temp. setting. After

another 1 hours, temp. rises by 1

C further.

The unit will run for further 6 hours then stops.

Temp. is higher than temp. setting so that room

temperature won't be too Iow for your sleep.

Remote Controller

SLEEP operation starts SLEEP operation stops

SLEEP

operation starts

SLEEP

operation stops

Approx.6hrs

1 hr

3 hrs

Rises 1

Temp.setting

Unit stop

In COOL, DRY mode

In HEAT mode

Decreases 2

1 hr

Sleep Operation

In HEAT mode

1 hours after SLEEP mode starts, temp

will become 2

C lower than temp.

setting. After another 1 hours, temp

decrease by 2

C further. After more

another 3 hours, temp. rises by 1

further. The unit will run for further 3

hours then stops. Temp. is lower than

temp. setting so that room temperature

won't be too high for your sleep.

In AUTO mode

The unit operates in corresponding sleep

mode adapted to the automatically selected

operation mode.

4. In FAN mode

It has no SLEEP function.

Note

The sleeping hours lasts 8 hours and couldn't be adjusted.

When timing on function is set, the sleeping function can't be set

After the sleeping function is set up, if user resets timing on

function, the sleeping function will be cancelled; the

machine will be in the state of timing-on. If the sleeping

function and timing-on function are set up at the same time,

no matter which one is operated earlier, the machine will be

off automatically, and the other function will also be cancelled.

Operation

La pagina sta caricando ...

Haier 2HUM18R03/R2(DB) Istruzioni per l'uso

Marca: Haier

Modello: 2HUM18R03/R2(DB)

Categoria: Condizionatori d'aria a sistema split

Tipo: Istruzioni per l'uso

Scarica il pdf

rapporto

in altre lingue

English: Haier 2HUM18R03/R2(DB) Operating instructions
français: Haier 2HUM18R03/R2(DB) Mode d'emploi

Haier 2HUM18R03/R2(DB) Istruzioni per l'uso

Haier 2HUM18R03/R2(DB) Istruzioni per l'uso

in altre lingue

Documenti correlati

Altri documenti