McCulloch LST42C-669 Manuale del proprietario

Model No.

Modelo nº

Modèle nº

Modell-Nr.

Modello nº

LST42C-669

MANUAL DEL USUARIO

PRINTED IN U.S.A. FORM NO. 40429 (REV. 1/7/08)

CAUTION:

Read Rules for Safe Operation

and Instructions Carefully

• Safety

• Assembly

• Operation

• Maintenance

42" SNOW THROWER

the fastest way to purchase parts

www.speedepart.com

™

PRECAUCIÓN:

Lea cuidadosamente las

instrucciones y las reglas para

una operación segura

• Seguridad

• Montaje

• Funcionamiento

• Mantenimiento

SOPLADOR DE NIEVE DE 42" (106 cm)

OWNERS MANUAL

MANUEL DU PROPRIÉTAIRE

SOUFFLEUSE À NEIGE 42 PO. (106 cm)

AVERTISSEMENT :

Lire et suivre attentivement les

instructions et consignes de

sécurité

• Sécurité

• Assemblage

• Utilisation

• Entretien

BEDIENUNGSANLEITUNG

SCHNEEFRÄSE 42" (106 cm)

AACHTUNG:

Lesen Sie bitte sowohl die

Hinweise zum sicheren Betrieb

sowie auch die Anweisungen

sorgfältig durch

• Sicherheit

• Zusammenbau

• Betrieb

• Wartung

MANUALE DEL PROPRIETARIO

SPARTINEVE A TURBINA 42" (106 cm)

ATTENZIONE:

Leggere attentamente le norme

di sicurezza e le istruzioni

• Sicurezza

• Montaggio

• Funzionamento

• Manutenzione

2

E

B

D

G

H

I

K

O

F

X

U

Y

C

W

L

Q

S,T

R

Z

KK

EE

N

CC

BB

AA

DD

M

J

JJ

FF

GG

II

V

P

HH

A

LL

NN

MM

REF. QTY DESCRIPTION

A 1 Hex Bolt, 3/8" x 3-1/4"

B 2 Hex Bolt, 5/16" x 1-3/4"

C 4 Hex Bolt, 5/16" x 3/4"

D 6 Hex Bolt, 1/4" x 1"

E 6 Hex Bolt, 3/8" x 1" (Thread

Forming)

F 2 Hex Bolt, 5/16" x 3/4"

(Thread Forming)

G 6 Carriage Bolt, 3/8" x 1"

H 2 Carriage Bolt, 5/16" x

1-3/4"

I 2 Carriage Bolt , 5/16" x

1-1/4"

J 4 Carriage Bolt, 5/16" x 1"

K 2 Carriage Bolt, 5/16" x 3/4"

REF. QTY DESCRIPTION

L 4 Shoulder Bolt

M 2 Shoulder Bolt

N 2 Shear Bolt (spare parts)

O 7 Lock Washer, 3/8"

P 7 Washer, 1/4"

Q 6 Washer, 5/16"

R 8 Washer, 1/2"

S 1 Washer, 3/8" (Thin)

T 3 Washer, 3/8"

U 2 Bowed Washer

V 6 Flanged Nut, 1/4"

W 1 Flanged Nut, 5/16"

X 10 Flanged Nut, 3/8"

Y 17 Nylock Nut, 5/16" (2 spare

parts)

REF. QTY DESCRIPTION

Z 2 Hex Lock Nut, 3/8"

AA 1 Spring

BB 3 Chute Keeper

CC 1 Trunnion

DD 2 Hairpin Cotter, 5/64"

EE 4 Hairpin Cotter, 1/8"

FF 1 Hairpin Cotter, 3/32"

GG 2 Lock Pin

HH 1 Plastic Cap

II 2 Nylon Tie

JJ 2 Chain, Tensioning

KK 2 Tail Reector

LL 1 Small Spacer

MM 1 Large Spacer

NN 1 Pulley

3

REF. CANT. DESCRIPCIÓN

A 1 Tuerca hexagonal de 3/8”

x 3-1/4"

B 2 Tuerca hexagonal de

5/16” x 1-3/4"

C 4 Tuerca hexagonal de

5/16" x 3/4"

D 6 Perno de cabeza

hexagonal de 1/4” x 1"

E 6 Perno de cabeza

hexagonal de 3/8” x 1"

(auto-roscante)

F 2 Perno de cabeza

hexagonal de 5/16” x 3/4"

(auto-roscante)

G 6 Perno de cabeza de

hongo y cuello cuadrado

de 3/8" x 1"

H 2 Perno de cabeza de

hongo y cuello cuadrado

de 5/16 x 1-3/4"

I 2 Perno de cabeza de

hongo y cuello cuadrado

de 5/16 x 1-1/4"

REF. CANT. DESCRIPCIÓN

J 4 Perno de cabeza de

hongo y cuello cuadrado

de 5/16” x 1"

K 2 Perno de cabeza de

hongo y cuello cuadrado

de 5/16 x 3/4"

L 4 Perno de tope

M 2 Perno de tope

N 2 Perno de seguridad

(piezas de repuesto)

O 7 Arandela de presión de

3/8"

P 7 Arandela de 1/4"

Q 6 Arandela de 5/16"

R 8 Arandela de 1/2"

S 1 Arandela de 3/8"

(delgada)

T 3 Arandela de 3/8"

U 2 Arandela curvada

V 6 Tuerca con brida de 1/4"

W 1 Tuerca con brida de 5/16"

X 10 Tuerca con brida de 3/8"

REF. CANT. DESCRIPCIÓN

Y 17 Tuerca Nylock de 5/16" (2

piezas de repuesto)

Z 2 Tuerca hexagonal de

cierre de 3/8

AA 1 1 resorte

BB 3 Sujetador del conducto

CC 1 Muñón de sujeción

DD 2 Pasador de horquilla de

5/64"

EE 4 Pasador de horquilla de

1/8"

FF 1 Pasador de horquilla de

3/32"

GG 2 Pasador de traba

HH 1 Tapa plástica

II 2 Tirante de Nylon

JJ 2 Cadena, tensora

KK 2 Reector de cola

LL 1 Espaciador pequeño

MM 1 Espaciador grande

NN 1 Polea

RÉF. QTÉ DESCRIPTION

A 1 Boulon hex., 3/8 x 3-1/4 po.

B 2 Boulon hex., 5/16 x 1-3/4 po.

C 4 Boulon hex., 5/16 x 3/4 po.

D 6 Boulon hex., 1/4 x 1 po.

E 6 Boulon hex., 3/8 x 1 po.

(auto-taraudeur)

F 2 Boulon hex., 5/16 x 3/4 po.

(auto-taraudeur)

G 6 Boulon de carrosserie, 3/8

x 1 po.

H 2 Boulon de carrosserie, 5/16

x 1-3/4 po.

I 2 Boulon de carrosserie , 5/16

x 1-1/4 po.

J 4 Boulon de carrosserie, 5/16

x 1 po.

K 2 Boulon de carrosserie, 5/16

x 3/4 po.

L 4 Boulon à épaulement

RÉF. QTÉ DESCRIPTION

M 2 Boulon à épaulement

N 2 Boulon de cisaillement

(pièces de rechange)

O 7 Rondelle de blocage, 3/8 po.

P 7 Rondelle, 1/4 po.

Q 6 Rondelle, 5/16 po.

R 8 Rondelle, 1/2 po.

S 1 Rondelle, 3/8 po. (ne)

T 3 Rondelle, 3/8 po.

U 2 Rondelle frein

V 6 Écrou à embase, 1/4 po.

W 1 Écrou à embase, 5/16 po.

X 10 Écrou à embase, 3/8 po.

Y 17 Écrou mécanique de

sécurité, 5/16 po. (2 pièces

de rechange)

Z 2 Écrou de blocage hex. 3/8

po.

RÉF. QTÉ DESCRIPTION

AA 1 1 Ressort

BB 3 Gâches de la goulotte

d’éjection

CC 1 Tourillon

DD 2 Goupille fendue, 5/64 po.

EE 4 Goupille fendue, 1/8 po.

FF 1 Goupille fendue, 3/32 po.

GG 2 Axe de blocage

HH 1 Capuchon en plastique

II 2 Attache en nylon

JJ 2 Chaîne de tension

KK 2 Catadioptre arrière

LL 1 Petite rondelle d’espacement

MM 1 Grande rondelle

d’espacement

NN 1 Poulie

4

BEZ. ANZ. BESCHREIBUNG

A 1 Sechskantschraube, 3/8"

x 3-1/4"

B 2 Sechskantschraube, 5/16"

x 1-3/4"

C 4 Sechskantschraube, 5/16"

x 3/4"

D 6 Sechskantschraube, 1/4"

x 1"

E 6 Sechskantschraube, 3/8" x

1" (gewindeschneidend)

F 2 Sechskantschraube,

5/16" x 3/4"

(gewindeschneidend)

G 6 Schlossschraube, 3/8" x 1"

H 2 Schlossschraube, 5/16" x

1-3/4"

I 2 Schlossschraube, 5/16" x

1-1/4"

J 4 Schlossschraube, 5/16"

x 1"

BEZ. ANZ. BESCHREIBUNG

K 2 Schlossschraube, 5/16"

x 3/4"

L 4 Gelenkschraube

M 2 Gelenkschraube

N 2 Scherschraube

(Ersatzteile)

O 7 Sicherungsscheibe, 3/8"

P 7 Unterlegscheibe, 1/4"

Q 6 Unterlegscheibe, 5/16"

R 8 Unterlegscheibe, 1/2"

S 1 Unterlegscheibe, 3/8"

(dünn)

T 3 Unterlegscheibe, 3/8"

U 2 Gewölbte Unterlegscheibe

V 6 Flanschmutter, 1/4"

W 1 Flanschmutter, 5/16"

X 10 Flanschmutter, 3/8"

Y 17 Sechskantmutter mit

Klemmteil, 5/16" (2

Ersatzteile)

RIF. QTÀ. DESCRIZIONE

A 1 Bullone esagonale da 3/8"

x 3-1/4"

B 2 Bullone esagonale da 5/16"

x 1-3/4"

C 4 Bullone esagonale da 5/16"

x 3/4"

D 6 Bullone esagonale da 1/4"

x 1"

E 6 Bullone esagonale da 3/8" x

1" (autolettante)

F 2 Bullone esagonale da 5/16"

x 3/4" (autolettante)

G 6 Chiavarda a testa rotonda

da 3/8" x 1"

H 2 Chiavarda a testa rotonda

da 5/16" x 1-3/4"

I 2 Chiavarda a testa rotonda

da 5/16" x 1-1/4"

J 4 Chiavarda a testa rotonda

da 5/16" x 1"

RIF. QTÀ. DESCRIZIONE

K 2 Chiavarda a testa rotonda

da 5/16" x 3/4"

L 4 Vite con gambo

parzialmente lettato

M 2 Vite con gambo

parzialmente lettato

N 2 Perno di sicurezza (pezzi di

ricambio)

O 7 Rondella elastica da 3/8"

P 7 Rondella da 1/4"

Q 6 Rondella da 5/16"

R 8 Rondella da 1/2"

S 1 Rondella da 3/8" (Thin)

T 3 Rondella da 3/8"

U 2 Rondella arcuata

V 6 Dado a colletto da 1/4"

W 1 Dado a colletto da 5/16"

X 10 Dado a colletto da 3/8"

BEZ. ANZ. BESCHREIBUNG

Z 2 Sechskantsicherungsmut

ter, 3/8"

AA 1 1 Feder

BB 3 Leitblechhalterung

CC 1 Zapfen

DD 2 Haarnadelsplint, 5/64"

EE 4 Haarnadelsplint, 1/8"

FF 1 Haarnadelsplint, 3/32"

GG 2 Steckbolzen

HH 1 Plastikkappe

II 2 Kabelbinder

JJ 2 Spannkette

KK 2 Rückwärtiger Reektor

LL 1 Kleines Distanzstück

MM 1 Großes Distanzstück

NN 1 Riemenscheibe

RIF. QTÀ. DESCRIZIONE

Y 17 Dado Nylock da 5/16" (2

parti di ricambio)

Z 2 Controdado esagonale da

3/8"

AA 1 1 molla

BB 3 Fissatore dello scivolo

CC 1 Perno di articolazione

DD 2 Chiavetta a forcella da 5/64"

EE 3 Chiavetta a forcella da 1/8"

FF 1 Chiavetta a forcella da 3/32"

GG 2 Spinotto di bloccaggio

HH 1 Tappo di plastica

II 2 Tirante di plastica

JJ 2 Catena, Messa in tensione

KK 2 Riettore di coda

LL 1 Piccolo distanziale

MM 1 Grande distanziale

NN 1 Puleggia

5

CARTON CONTENTS

1. Suspension Arms (2)

2. Left Hand Side Plate

3. Right Hand Side Plate

4. Anti-rotation Bracket

5. Engagement Rod (Not used on some models)

6. Engine Pulley Keeper (Not used on some models)

7. Chute Crank Rod Assembly

8. Support Tube, Crank Rod

9. Lift Handle and Cable

10. Cable Bracket

11. L.H. Hanger Bracket (Outside Mounting)

12. R.H. Hanger Bracket (Outside Mounting)

13. Clutch Idler Assembly

14. V-Belt, Drive (Short) #46989

15 V-Belt, Drive (Long) #48138

16. V-Belt, Auger (Attached to Housing Assembly)

17. Chute and Control Cable Assembly

18. Housing Assembly

19. L.H. Hanger Bracket (Inside Mounting)

20. R.H. Hanger Bracket (Inside Mounting)

Hardware Package (Stored inside Plastic Keg)

14

1

2

4

5

6

12

9

8

10

20

19

11

17

16

15

18

13

7

3

6

CONTENIDO DE LA CAJA

1. Brazos de suspensión (2)

2. Placa lateral izquierda

3. Placa lateral derecha

4. Soporte antirrotación

5. Varilla de enganche (No se utiliza en algunos modelos)

6. Sujetador de la polea motor (No se utiliza en algunos

modelos)

7. Conjunto varilla manivela del conducto

8. Tubo soporte, varilla de la manivela

9. Manivela de elevación y cable

10. Soporte para el cable

11. Soporte de suspensión lado izquierdo (Se monta en el

exterior)

12. Soporte de suspensión lado derecho (Se monta en el

exterior)

13. Conjunto de embrague/polea libre

14. Correa trapezoidal, transmisión (corta) #46989

15. Correa trapezoidal, transmisión (larga) #48138

16. Correa trapezoidal, barrena (enganchada al conjunto de la

carcasa)

17. Conjunto de cable de control y de conducto.

18. Carcasa

19. Soporte de suspensión lado izquierdo (Se monta en el

interior)

20. Soporte de suspensión lado derecho (Se monta en el

interior)

Paquete de accesorios (se guarda en el interior de una bolsa

de plástico)

CONTENU DU CARTON

1. Bras de suspension (2)

2. Plaque latérale gauche

3. Plaque latérale droite

4. Patte anti-rotation

5. Biellette de mise en prise (n'est pas utilisée sur certains

modèles)

6. Gâche de la poulie du moteur (n'est pas utilisée sur certains

modèles)

7. Bielle de la goulotte d’éjection

8. Tube de support de la bielle de la goulotte

9. Poignée d’élévation et câble

10. Support de xation du câble

INHALT DES KARTONS

1. Aufhängungsarme (2)

2. Linke Seitenplatte

3. Rechte Seitenplatte

4. Verdrehschutzhalterung

5. Einrückstange (kommt nicht bei allen Modellen zum

Einsatz)

6. Keilriemenhalter (kommt nicht bei allen Modellen zum

Einsatz)

7. Leitblechverstellstangenbaugruppe

8. Stützrohr, Verstellstange

9. Hebergriff und Kabel

CONTENUTO DEI CARTONI

1. Bracci di sospensione (2)

2. Piastra laterale sinistra

3. Piastra laterale destra

4. Staffa antirotazione

5. Asta di inserimento (Non usato in alcuni modelli)

6. Fissatore della puleggia motrice (Non usato in alcuni

modelli)

7. Gruppo asta manovella dello scivolo

8. Tubo di supporto, Asta manovella

9. Maniglia e cavo di sollevamento

10. Staffa del cavo

11. Support suspendu gauche (montage extérieur)

12. Support suspendu droit (montage extérieur)

13. Ensemble embrayage et galet tendeur

14. Petite courroie en V du mécanisme d’entraînement no.

46989

15. Longue courroie en V du mécanisme d’entraînement no.

48138

16. Courroie en V de la tarière (xée au carter de protection)

17. Ensemble de la goulotte d’éjection et du câble de

commande

18. Carter de protection

19. Support suspendu gauche (montage intérieur)

20. Support suspendu droit (montage intérieur)

Sac de pièces de quincaillerie (située à l’intérieur d’un baril en

plastique)

10. Kabelkonsole

11. linke Hängerhalterung (Außenmontage)

12. rechte Hängerhalterung (Außenmontage)

13. Kupplungs-/Umlenkrollenbaugruppe

14. Keilriemen, Antrieb (kurz) Nr. 46989

15 Keilriemen, Antrieb (lang) Nr. 48138

16. Keilriemen, Schnecke (Mit der Gehäusebaugruppe

verbunden)

17. Leitblech- und Steuerkabelbaugruppe

18. Gehäusebaugruppe

19. linke Hängerhalterung (Innenmontage)

20. rechte Hängerhalterung (Innenmontage)

Kleinteilepackung (im Plastikfass untergebracht)

11. Staffa del gancio sinistro (montaggio esterno)

12. Staffa del gancio destro (montaggio esterno)

13. Gruppo innesto ingranaggio folle

14. Cinghia a V, motrice (corta) no.46989

15 Cinghia a V, motrice (lunga) no. 48138

16. Cinghia a V, Coclea (Attaccata al gruppo

alloggiamento)

17. Gruppo scivolo e cavo di comando

18. Gruppo alloggiamento

19. Staffa del gancio sinistro (montaggio interno)

20. Staffa del gancio destro (montaggio interno)

Pacchetto bulloneria (conservato all’interno del barilotto

di plastica)

7

SAFETY

Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment.

Exercise caution at all times, when using power equipment.

• Read this owner's manual carefully and know how to

operate your snow thrower and how to stop the unit and

disengage the controls quickly.

• Never allow children to operate the equipment.

• Never allow adults to operate the equipment without

proper instruction.

• Keep the area of operation clear of all persons, especially

small children, and pets.

• Thoroughly inspect the area where the equipment is to

be used and remove all door mats, sleds, boards, wires

and other foreign objects.

• Disengage all clutches and shift into neutral before

starting engine.

• Do not operate equipment without wearing adequate

winter outer garments.

• Wear substantial footwear which will protect feet and

improve footing on slippery surfaces.

• Check fuel before starting the engine. Do not remove the

fuel cap or ll the fuel tank while the engine is running

or hot. Do not ll the fuel tank indoors. Gasoline is an

extremely ammable fuel.

• Make sure the snow thrower height is adjusted to clear

the type surface it will be used on.

• Do not use the snow thrower without the rear weight

attached to the tractor.

• Never make any adjustments while the engine is

running.

• Always wear safety glasses or eye shield during operation

or while performing adjustment or repair.

• Do not place hands or feet near rotating parts. Keep

clear of the discharge opening at all times.

• Use extreme caution when operating on or crossing

gravel surfaces.

• Do not carry passengers.

• After striking a foreign object, stop the engine, remove

the wire from the spark plug and then thoroughly inspect

the snow thrower for damage. Repair any damage before

restarting and operating the snow thrower.

• If the snow thrower starts to vibrate abnormally, stop the

engine immediately and check for the cause. Vibration

is generally a warning of trouble.

• Stop the engine whenever you leave the operating

position, before unclogging the snow thrower or making

any adjustments or inspections.

• Take all possible precautions when leaving the unit

unattended. Disengage the attachment clutch lever or

switch, lower the snow thrower, shift into neutral, set the

parking brake, stop the engine and remove the key.

• When cleaning, repairing or inspecting, make certain all

moving parts have stopped. Disconnect the spark plug

wire and keep it away from the plug to prevent accidental

starting.

• Do not run engine indoors except when transporting the

snow thrower in or out of the building. Open the outside

doors. Exhaust fumes are dangerous.

• Do not clear snow across the face of slopes. Exercise

extreme caution when changing direction on slopes.

Do not attempt to clear steep slopes. Refer to the slope

guide on page 79 of this manual.

• Never operate the snow thrower without guards, plates

or other safety protection devices in place.

• Never operate the snow thrower near glass enclosures,

automobiles, window wells, drop offs etc. without proper

adjustment of the snow thrower discharge angle.

• Never direct discharge at bystanders or allow anyone in

front of the snow thrower.

• Never run the snow thrower into material at high

speeds.

• Do not overload the machine capacity by attempting to

clear snow at too fast a rate.

• Never operate the machine at high transport speed

on slippery surfaces. Look behind and use care when

backing up.

• Watch for trafc and stay alert when crossing or operating

near roadways.

• Disengage power to the snow thrower when transporting

or when not in use.

• Use only attachments and accessories approved by

the manufacturer of the snow thrower (such as wheel

weights, counter weights, cabs etc.)

• Never operate the snow thrower without good visibility

or light.

IMPORTANT:

Rear wheel weights and tire chains are required to

provide extra traction and stability when using this

snow thrower attachment. These items are available

where you purchased your tractor.

WHEEL WEIGHTS TIRE CHAINS

8

• Remove all parts and hardware packages from the

carton. Lay out parts and hardware and identify using

the illustrations on pages 2 and 5.

NOTE: Not all of the supplied parts and hardware will be

needed for your particular tractor. Unneeded items may

be discarded after you have completed assembly and

checked operation of unit. DO NOT DISCARD the two

spare shear bolts (N) and 5/16" nylock nuts (Y). Refer to

the Service and Adjustments section on page 28.

REMOVAL OF PARTS FROM CARTON

TOOLS REQUIRED FOR ASSEMBLY

(2) 7/16" Wrenches

(2) 1/2" Wrenches

(2) 9/16" Wrenches

(2) 3/4" Wrenches

(1) Screw Driver

(1) Knife

ADDITIONAL ITEMS REQUIRED

General Purpose Grease

TRACTOR PREPARATION

Before performing these instructions, refer to the Service

and Adjustments section of your tractor owner's manual

for specic safety instructions.

• Allow engine, mufer and exhaust deector to cool

before beginning.

• Remove any front or rear attachment which is

mounted to your tractor.

• Remove the mower deck. Refer to your tractor owner's

manual for removal instructions. Mark all loose parts

and save for reassembly.

• Remove the tractor hood. Refer to your tractor owner's

manual for removal instructions.

CAUTION: Before starting to assemble the

snow thrower, remove the spark plug wire(s),

set the parking brake and remove the key

from the tractor ignition.

FIGURE 2 RIGHT SIDE VIEW

IMPORTANT: Right hand (R.H.) and left hand (L.H.) side

of the tractor are determined from the operators position

while seated on the tractor.

REMOVE

FRONT SCREWS

REMOVE

BROWNING SHIELD

MOWER DECK

SUSPENSION

BRACKET

FIGURE 1

INSTRUCTIONS FOR TRACTORS WITH

SINGLE FRONT DECK SUSPENSION

BRACKET

STEP 2: (SEE FIGURE 2)

• Remove the browning shield from the front of the

tractor as shown. Hold onto the shield as you remove

the second screw to prevent it from falling.

• Be sure to reinstall the browning shield when so

instructed in step 3.

IDENTIFY YOU TRACTOR

STEP 1: (SEE FIGURE 1)

• Look under the front of your tractor. If there is a single

mower deck suspension bracket located underneath

the middle of the front axle, continue on to step 2.

If your tractor does not have a mower deck

suspension bracket underneath the middle of the

front axle, skip to step 21 on page 14 for tractors

with dual suspension brackets.

ASSEMBLY

9

STEP 4: (SEE FIGURE 4)

• Assemble a shoulder bolt (L) and a 3/8" washer (T) to

the outside of R.H. side plate, securing it with a 3/8"

anged nut (X). Repeat for L.H. side plate.

FIGURE 4 RIGHT SIDE VIEW

FIGURE 3 RIGHT SIDE VIEW

5/16"

NYLOCK

NUT (Y)

5/16" x 1"

CARRIAGE BOLT (J)

ENGINE MOUNTING

PLATE

(4) 1/2" WASHERS (R)

(3) 3/8" FLANGE NUTS (X)

(3) 3/8" x 1"

CARRIAGE

BOLTS (G)

SEE NOTE

3/8" WASHER (T)

SHOULDER

BOLT (L)

3/8" FLANGED

NUT (X)

INSTALL SIDE PLATES

STEP 3: (SEE FIGURE 3)

• Fasten the R.H. Side Plate (bend facing out) to the

front three holes in the tractor frame using three 3/8"

x 1" carriage bolts (G), three 1/2" washers (R) (see

note) and three 3/8" ange nuts (X). For the rear hole,

use a 5/16" x 1" carriage bolt (J), a 1/2" washer (R)

and a 5/16" nylock nut (Y). Place the 1/2" washers (R)

between the tractor frame and the side plate. Repeat

for L.H. side plate.

• Reinstall the browning shield onto the tractor frame

using the original screws.

NOTE: If there is an engine mounting plate (shown with

dotted lines) leave the 1/2 washer off the bolt that goes

through the plate.

INSTALL HANGER BRACKETS AND SHOULDER

BOLTS TO OUTSIDE OF FRAME

STEP 5: (SEE FIGURE 5)

•

Remove the bolt, if present, in the hole directly behind

the brake rod on the left side of the tractor frame.

• Attach the L.H. Hanger Bracket (tube facing out) to the

hole using a 5/16" x 3/4" self threading bolt (F).

• Install a round head shoulder bolt (M) into the hole

that is 9-1/2" to the rear of the bolt you just installed.

Secure it with a 3/8" ange nut (X) on the inside of the

frame.

FIGURE 5 LEFT SIDE VIEW

5/16" x 3/4" SELF

THREADING BOLT (F)

L.H. HANGER

BRACKET

BRAKE ROD

3/8" FLANGED

NUT (X)

SHOULDER

BOLT (M)

5/16" x 3/4" SELF

THREADING BOLT (F)

R.H. HANGER

BRACKET

RIGHT END OF

BRAKE ROD

3/8" FLANGED

NUT (X)

SHOULDER

BOLT (M)

STEP 6: (SEE FIGURE 6)

• Remove the bracket, if present, from the hole directly

behind the end of the brake rod on the right side of

the tractor frame. Store the bracket and bolt.

• Attach the R.H. Hanger Bracket to the hole using a

5/16" x 3/4" self threading bolt (F).

• Install a round head shoulder bolt (M) into the hole

that is 9-1/2" to the rear of the bolt you just installed.

Secure it with a 3/8" ange nut (X) on the inside of the

frame.

FIGURE 6 RIGHT SIDE VIEW

10

3/8" X 3-1/4"

HEX BOLT

(A)

LARGE SPACER (MM)

PULLEY (NN)

3/8" LOCKWASHER (O)

3/8" HEX LOCK NUT (Z)

3/8"

WASHER (T)

LONG END

OF HUB

STEP 7: (SEE FIGURE 7)

• Attach the pulley (long end of hub facing down) and

the large spacer (MM) to the hole shown in the clutch/

idler assembly. Use a 3/8" x 3-1/4" hex bolt (A), a 3/8"

washer (T), a 3/8" lock washer (O) and a 3/8" hex lock

nut (Z).

FIGURE 7

FIGURE 9

STEP 9: (SEE FIGURE 9)

• Attach the cable bracket to the slot shown in the

clutch/idler assembly using a 5/16" x 3/4" carriage

bolt (K) and a 5/16" nylock nut (Y). Place the bolt in

the front hole of the bracket and in the end of the slot

closest to the pulley. Do not tighten yet.

CABLE

BRACKET

5/16" x 3/4"

CARRIAGE BOLT (K)

5/16" NYLOCK

NUT (Y)

THIS SECTION IS FOR TRACTORS WITH A

MANUAL ATTACHMENT CLUTCH

If your tractor has an electric attachment clutch go to

step 14 on page 12.

FIGURE 10

HEX BOLTS

(#48138)

DRIVE BELT

FLAT IDLER

PULLEYS

STOP

Did you select the correct drive belt for your

tractor? Using the wrong length belt may

cause premature bearing or belt failure.

STEP 10: (SEE FIGURE 10)

• Two different length drive belts are included with

your snow thrower. Tractors with manual attachment

clutches and single front deck suspension brackets use

the 56" drive belt with #48138 printed on the outside of

the belt. DO NOT USE the other belt.

• Slightly loosen the hex bolt next to the at idler pulley.

Install the drive belt down between the hex bolt and the

at idler pulley with the at side of the belt against the

pulley. Retighten the hex bolt.

• Loop the belt around the large v-pulley, placing it

between the v-pulley and the hex bolt next to the pulley.

Place the belt to the inside of the other at idler pulley.

5/16" NYLOCK

NUT (Y)

5/16" x 3/4"

HEX BOLT (C)

TENSIONING CHAIN (JJ)

FIGURE 8

STEP 8: (SEE FIGURE 8)

• Attach the two suspension arms to the rear of the

clutch/idler assembly using two 5/16" x 3/4" hex bolts

(C) and 5/16" nylock nuts (Y) for each arm. Place the

arms on the outside of the frame with the notches to

the rear.

• Insert a tensioning chain through the hole shown and

attach the end link to the spring on the lower idler arm.

11

PIVOT LOCK PIN (GG)

(use this hole)

SHOULDER

BOLT (M)

L.H. HANGER

BRACKET

1/8" HAIRPIN

COTTER (EE)

NYLON TIE (II)

MOWER

CLUTCH

CABLE

FIGURE 12 VIEWED FROM LEFT SIDE

STEP 13: (SEE FIGURE 13)

• Assemble the drive belt onto the engine pulley rst

and then onto the large pulley on top of the clutch/

idler assembly. The belt must be placed inside the

engine pulley belt keeper(s) and between the large

pulley and the keeper bolt next to it.

IMPORTANT: Do Not assemble the "V" belt outside of

the engine pulley keepers or outside of the keeper bolt

next to the large pulley.

• Go to step 48 on page 21.

FIGURE 13 VIEWED FROM UNDERNEATH

ENGINE

PULLEY

ENGINE

PULLEY

Left Side

of Tractor

ENGINE

PULLEY

KEEPER

ENGINE

PULLEY

KEEPER

KEEPER BOLT

IDLER

PULLEY

CLUTCH/IDLER ASSEMBLY

FIGURE 11

5/64" HAIR

COTTER PIN

SPACER

1/4" WASHER

TRACTOR'S

CLUTCH CABLE

CABLE

BRACKET

GROOVE

5/64" HAIR

COTTER PIN (DD)

1/4" WASHER (P)

SPACER (LL)

TRACTOR'S

CLUTCH CABLE

CABLE

BRACKET

5/64" HAIR

COTTER PIN (DD)

ATTACH CLUTCH IDLER ASSEMBLY TO TRACTOR

STEP 12: (SEE FIGURE 12)

• Attach the clutch/idler assembly to the tractor frame.

Hook the notched suspension arms onto the two

shoulder bolts (M) assembled to the outside of the

tractor frame. Lift the front of the assembly and attach

it to the R.H. and L.H. hanger brackets using two pivot

lock pins (GG) and 1/8" hairpin cotters (EE).

• Loosely attach the mower clutch cable to the left side

of the tractor frame with a nylon tie (II). Do not pull

the nylon tie completely tight. The cable may need to

be removed from the nylon tie when using the mower

deck.

STEP 11: (SEE FIGURE 11)

• Find the cable clip that is attached to the left side

of the tractor frame underneath the footrest. Open

the clip and remove the mower clutch cable. Do not

remove the clip from the tractor frame. The cable

reattaches to the clip when using the mower deck.

• Move the attachment clutch lever on the dash panel to

the disengaged position.

• Place the clutch/idler assembly on the oor on the left

side of the tractor.

• Attach the tractor's mower clutch cable to the cable

bracket on the clutch/idler assembly. Secure the cable

housing guide (groove down) to the cable bracket

using the original collar and a 5/64" hair cotter pin (DD).

• Place a spacer (LL) on the welded pin on the idler

arm. Hook the end of the clutch cable spring over the

pin and secure it with a 1/4" washer (P) and a 5/64"

hair cotter pin (DD).

• Align cable bracket with welded pin and tighten the

nut assembled in step 9.

12

THIS SECTION IS FOR TRACTORS WITH AN

ELECTRIC ATTACHMENT CLUTCH

STEP 14: (SEE FIGURE 14)

• Attach the two suspension arms to the rear of the

clutch/idler assembly using two 5/16" x 3/4" hex bolts

(C) and 5/16" nylock nuts (Y) for each arm. Place the

arms on the outside of the frame with the notches to

the rear.

• Insert a tensioning chain through the hole shown and

attach the end link to the spring on the lower idler arm.

FIGURE 14

FIGURE 16 VIEW OF BOTTOM

STEP 16: (SEE FIGURE 16)

• Hook one end of the spring supplied in the parts bag

through the end link of the tensioning chain.

• With the clutch/idler assembly turned upside down,

hook the other end of the spring onto the end of the

bolt and nut which secure the idler pulley to the upper

idler arm. Assemble a 3/8" hex lock nut (Z) onto the

bolt and nut, leaving enough gap between the nuts for

the spring to pivot freely.

• Attach a 3/32" hairpin cotter (FF) to the chain, placing

it in the fth link from the spring.

CHAIN

(L.H. SIDE)

3/32" HAIR

COTTER PIN (FF)

5TH LINK

LEFT

SIDE

3/8" HEX

LOCK NUT (Z)

SPRING

RIGHT

SIDE

ATTACH

SPRING

HERE

STEP 15: (SEE FIGURE 15)

• Turn the clutch/idler assembly upside down and insert

the second tensioning chain (JJ) through the left front

hole.

FIGURE 15

TENSIONING CHAIN (JJ)

LEFT FRONT HOLE

STEP 17: (SEE TABLE 1)

• Two different length drive belts are included with

your snow thrower. Use the table below to select

the correct drive belt for your type tractor. The part

number is printed on the outside of the belt .

• Set aside the belt that is not for your tractor to avoid

accidentally using it.

SELECT THE CORRECT DRIVE BELT

(Electric clutch tractors with a single front deck

suspension bracket)

55" BELT (PART #46989)

TRACTOR TYPE DECK SIZE CLUTCH TYPE

(LT) Lawn Tractor 38", 42" Electric

56" BELT (PART #48138)

TRACTOR TYPE DECK SIZE CLUTCH TYPE

(LT) Lawn Tractor 48" Electric

(GT) Garden Tractor 48", 54" Electric

TABLE 1

5/16" NYLOCK

NUT (Y)

5/16" x 3/4"

HEX BOLT (C)

TENSIONING CHAIN (JJ)

13

STEP 19: (SEE FIGURE 18)

• Attach the clutch/idler assembly to the tractor frame.

Hook the notched suspension arms onto the two

shoulder bolts (M) assembled to the outside of the

tractor frame. Lift the front of the assembly and attach

it to the R.H. and L.H. hanger brackets using two pivot

lock pins (GG) and 1/8" hairpin cotters (EE).

PIVOT LOCK PIN (GG)

(use second hole)

SHOULDER

BOLT (M)

1/8" HAIRPIN

COTTER (EE)

L.H. HANGER

BRACKET

FIGURE 18 VIEWED FROM LEFT SIDE

STEP 20: (SEE FIGURE 19)

• Assemble the drive belt onto the engine pulley rst

and then onto the large pulley on top of the clutch/

idler assembly. Place the belt to the inside of the idler

pulley and the belt keeper bolt located beside the

large pulley.

• Place tension on the belt by pulling the left side

tensioning chain (JJ) out as far as the 3/32" hairpin

cotter in the chain will allow. Secure the chain in this

position by inserting a 1/8" hairpin cotter (EE) through

the chain.

IMPORTANT: Do Not assemble the drive belt around the

outside of the keeper bolt beside the large pulley.

• Go to step 48 on page 22.

FIGURE 19 VIEWED FROM UNDERNEATH

1/8" HAIRPIN

COTTER (EE)

ENGINE

PULLEY

ENGINE

PULLEY

KEEPER

BOLT

IDLER

PULLEY

CHAIN (JJ)

(L.H. SIDE)

FIGURE 17

STEP 18: (SEE FIGURE 17)

• Turn the clutch/idler assembly right side up.

• Slightly loosen the hex bolt next to the at idler pulley.

Install the drive belt down between the hex bolt and the

at idler pulley with the at side of the belt against the

pulley. Retighten the hex bolt.

• Loop the belt around the large v-pulley, placing it

between the v-pulley and the hex bolt next to the pulley.

STOP

Did you choose the correct drive belt for

your tractor? Using the wrong length belt

may cause premature bearing or belt failure.

CLUTCH/IDLER ASSEMBLY

HEX BOLTS

DRIVE BELT

FLAT IDLER

PULLEY

14

STEP 22: (SEE FIGURE 21)

• Fasten the R.H. Side Plate (bend facing out) to the

front three holes shown in the tractor frame using

three 3/8" x 1" thread forming bolts (E), three 3/8"

lock washers (O) and one 1/2" washer (R) placed on

the third bolt as a shim between the side plate and

the frame. Tighten all bolts. Repeat for the L.H. side.

NOTE: If you installed a bolt in the fourth hole in step 21,

assemble a 5/16" ange nut (W) onto the bolt after the

side plate is installed.

• Go to step 25 on this page.

(3) 3/8" x 1"

THREAD FORMING

BOLTS (E)

5/16" FLANGED

NUT (W)

(SEE NOTE)

(3) 3/8" LOCK

WASHERS (O)

1/2" WASHER (R)

5/16" x 1"

CARRIAGE BOLT (J)

(SEE NOTE)

FIGURE 21 RIGHT SIDE VIEW

SUSPENSION

BRACKET

REMOVE BOLTS

IF PRESENT

FIGURE 22 RIGHT SIDE VIEW

STEP 23: (SEE FIGURE 22)

•

Remove any bolts found in the holes shown.

STEP 21: (SEE FIGURE 20)

•

Remove bolts from front three holes shown.

• If a bolt is present in the fourth hole, replace it with a

5/16" x 1" carriage bolt (J) without a nut. The bracket

fastened to inside of frame must remain in place.

FRONT

SUSPENSION

BRACKET

REPLACE BOLT

(IF PRESENT)

REMOVE BOLTS

(IF PRESENT)

FIGURE 20 RIGHT SIDE VIEW

INSTRUCTIONS FOR TRACTORS WITH DUAL

FRONT DECK SUSPENSION BRACKETS

FASTEN SIDE PLATES TO TRACTOR

If your tractor resembles gure 20, go to step 21.

If your tractor resembles gure 22, go to step 23.

STEP 25: (SEE FIGURE 24)

•

Assemble a shoulder bolt (L) and a 3/8" washer (T) to

the outside of each side plate, securing them with a

3/8" anged nut (X).

FIGURE 24 RIGHT SIDE VIEW

3/8" WASHER (T)

SHOULDER

BOLT (L)

3/8" FLANGED

NUT (X)

STEP 24: (SEE FIGURE 23)

• Fasten the R.H. Side Plate (bend facing out) to the

three holes shown in the tractor frame. Use three 3/8"

x 1" thread forming bolts (E), 3/8" lock washers (O)

and 1/2" washers (R). Use the 1/2" washers as shims

between the Side Plate and the tractor frame. Tighten

all bolts and repeat for the L.H. side.

NOTE: If the bolt inserts freely into the front hole, assemble

a 3/8" anged nut (X) onto the bolt.

(3) 3/8" x 1"

THREAD FORMING

BOLTS (E)

(3) 3/8" LOCK

WASHERS (O)

3/8" FLANGED NUT (X)

(SEE NOTE)

(3) 1/2" WASHERS (R)

FIGURE 23 RIGHT SIDE VIEW

15

FIGURE 28 RIGHT SIDE VIEW

INSTALLING HANGER BRACKETS

For better clearance, lower the tractor's suspension arms

using the attachment lift lever.

STEP 26: (SEE FIGURE 25 or 26)

On Tractors With Foot Rest Brackets

• Remove the bolt and nut that fasten the L.H. and R.H.

foot rest brackets to the frame.

• Attach the L.H. Hanger Bracket (marked "L") to the

inside of the tractor frame using two 3/8" x 1" carriage

bolts (G) and 3/8" anged nuts (X). Bolt heads go on

inside of tractor frame. Repeat for the R.H. side.

FIGURE 26 LEFT SIDE VIEW

FIGURE 25 LEFT SIDE VIEW

On Tractors Without Foot Rest Brackets

• Find the empty hole beneath the foot rest. Attach the

L.H. Hanger Bracket (marked "L") to the inside of the

frame using a 3/8" x 1" carriage bolt (G) and a 3/8"

anged nut (X). Bolt head goes on inside of tractor

frame. Repeat for the R.H. side.

STEP 28: (SEE FIGURE 28)

• Assemble a shoulder bolt (L) and 3/8" anged nut (X)

to the R.H. side of the tractor frame, using the rst

empty hole to the rear of the R.H. hanger bracket. Bolt

goes on inside of frame.

FIGURE 27 LEFT SIDE VIEW

INSTALLING SHOULDER BOLTS

STEP 27: (SEE FIGURE 27)

• Remove the bolt, washer and nut which fasten the

sway bar bracket to the L.H. side of the tractor frame.

Replace with a shoulder bolt (L) and a 3/8" anged

nut (X). Bolt goes on inside of frame.

BOLT REMOVED

FROM THIS HOLE

SWAY BAR

BRACKET

SHOULDER BOLT (L)

3/8"

FLANGED

NUT (X)

3/8" x 1"

CARRIAGE

BOLT (G)

3/8" FLANGED

NUT (X)

L.H. HANGER

BRACKET

SUSPENSION ARM

SHOULDER BOLT (L)

3/8"

FLANGED

NUT (X)

R.H. HANGER BRACKET

BOLT REMOVED

FROM THIS HOLE

3/8" x 1"

CARRIAGE

BOLT (K)

3/8" FLANGED

NUT (X)

L.H. HANGER

BRACKET

SUSPENSION ARM

16

INSTALLING CLUTCH/IDLER ASSEMBLY

This section covers the installation of the Clutch/Idler

assembly to tractors with attachment clutches that are

either rod operated (p. 16), cable operated (p. 19) or

electric (p. 20). Use the appropriate instructions for your

tractor.

ROD OPERATED MANUAL ATTACHMENT CLUTCH

STEP 29: (SEE FIGURE 29)

• Move the attachment clutch lever on the dash panel to

the disengaged (down) position.

• Screw the trunnion (CC) onto the end of the snow

thrower engagement rod.

• Locate the clutch arm (where the mower clutch rod

was connected) underneath the right hand side the

tractor, just to the inside of the suspension arm. If

there is an extension attached to the clutch lever, the

extension, bolt and nut must be removed and stored

with the mower deck.

IMPORTANT: Re-attach the extension to the clutch

lever before reinstalling the mower deck.

• Position the engagement rod to the inside of the

clutch arm and insert the drilled end of the rod

through the arm. Secure with a 5/64" hairpin cotter

(DD).

FIGURE 29 RIGHT SIDE VIEW

ENGAGEMENT ROD

5/64" HAIRPIN

COTTER (DD)

TRACTOR'S CLUTCH ARM

SUSPENSION ARM

TRUNNION (CC)

REMOVE EXTENSION,

BOLT AND NUT

(IF PRESENT)

STEP 30: (SEE FIGURE 30)

• Attach the two suspension arms to the inside of the

clutch/idler assembly using two 5/16" x 3/4" hex bolts

(C), 5/16" washers (Q) and 5/16" nylock nuts (Y) for

each arm. Place the washers between the arms and

the assembly frame.

• Insert a tensioning chain through the hole shown and

attach the end link to the spring on the lower idler arm.

FIGURE 30

5/16" x 3/4"

HEX BOLT (C)

5/16" NYLOCK

NUT (Y)

TENSIONING CHAIN (JJ)

5/16" WASHER (Q)

FIGURE 31

STOP

Did you choose the correct drive belt for

your tractor? Using the wrong length belt

may cause premature bearing or belt failure.

HEX BOLTS

DRIVE BELT

FLAT IDLER

PULLEY

(#46989)

STEP 31: (SEE FIGURE 31)

• Two different length drive belts are included with

your snow thrower. Tractors with manual attachment

clutches and dual front deck suspension brackets use

the 55" drive belt with #46989 printed on the outside

of the belt. DO NOT USE the other belt.

• Slightly loosen the hex bolt next to the at idler pulley.

Install the drive belt down between the hex bolt and the

at idler pulley with the at side of the belt against the

pulley. Retighten the hex bolt.

• Loop the belt around the large v-pulley, placing it

between the v-pulley and the hex bolt next to the pulley.

17

FIGURE 33 RIGHT SIDE VIEW

FIGURE 32 RIGHT SIDE VIEW

PIVOT LOCK PIN (GG)

(use second hole)

1/8" HAIRPIN COTTER (EE)

ENGAGEMENT

ROD

STEP 33: (SEE FIGURE 33)

• Make sure the attachment clutch lever on the dash

panel is in the disengaged (down) position.

• Pivot the upper idler arm so that it rests against the

stop bolt and is pointing toward the front as shown.

Screw the trunnion (CC) along the threads of the

engagement rod until it is aligned at the front end of

the idler arm slot. Attach the trunnion (CC) to the slot

using the 3/8" thin washer (S) and a 5/64" hairpin

cotter (DD).

• Remove the engine pulley keeper from the side of

the tractor frame by removing the washer and nut

that secure the keeper. Attach the new pulley keeper

supplied with the snow thrower, reusing the original

bolt, washer and nut.

NOTE: Some tractors may already be equipped with a

pulley keeper that is identical to the new one supplied.

IDLER ARM

5/64" HAIRPIN

COTTER (DD)

TRUNNION (CC)

STOP BOLT

3/8" THIN

WASHER (S)

NEW ENGINE PULLEY KEEPER WITH

ORIGINAL BOLT, NUT AND WASHER

STEP 34: (SEE FIGURE 34)

• Assemble the short "V" belt onto the engine pulley

and then onto the large pulley on top of the clutch/

idler assembly. The belt must be placed to the inside

of the engine pulley keeper, the idler pulley and the

keeper bolt located beside the large pulley.

IMPORTANT: Do Not assemble the "V" belt around the

outside of the engine pulley keeper or the keeper bolt.

• Go to step 48 on page 22.

FIGURE 34 VIEWED FROM UNDERNEATH

ENGINE

PULLEY

KEEPER BOLT

IDLER

PULLEY

ENGINE

PULLEY

KEEPER

Left Side

of Tractor

CLUTCH/IDLER ASSEMBLY

STEP 32: (SEE FIGURE 32)

• Be sure to lift up the front end of the engagement rod

as shown when performing the next operation. You

can temporarily support the rod using a rubber band

tied to the engine pulley keeper.

• Attach the clutch/idler assembly to the tractor frame

as follows. Hook the assembly's notched arms onto

the two shoulder bolts you assembled to the inside

of the tractor frame. Lift the front of the assembly and

attach it to the R.H. and L.H. hanger brackets using

two pivot lock pins (GG) and 1/8" hairpin cotters (EE).

18

FIGURE 36

FIGURE 38

STEP 36: (SEE FIGURE 36)

• Assemble the cable bracket to the clutch/idler

assembly using two 5/16" x 3/4" carriage bolts (K) and

5/16" nylock nuts (Y). Use the two front holes in the

cable bracket if your tractor has a 42" mower deck.

Use the two rear holes if your tractor has a 46" mower

deck.

STEP 38: (SEE FIGURE 38)

• Move the attachment clutch lever on the dash panel to

the disengaged (down) position.

• Place the clutch/idler assembly on the oor on the right

side of the tractor.

• Attach the tractor's clutch cable to the cable bracket.

Secure the cable housing guide (groove down) to the

cable bracket using the original collar and a 5/64" hair

cotter pin (DD).

• Place a spacer (LL) on the welded pin on the idler arm.

Hook the end of the clutch spring over the pin and

secure it with a 1/4" washer (P) and a 5/64" hair cotter

pin (DD).

CABLE

BRACKET

5/16" x 3/4"

CARRIAGE BOLT (K)

5/16" NYLOCK

NUT (Y)

42"

DECKS

46"

DECKS

GROOVE

TRACTOR'S

CLUTCH CABLE

5/64" HAIR

COTTER PIN (NN)

1/4" WASHER (X)

SPACER (HH)

TRACTOR'S

CLUTCH CABLE

5/64" HAIR

COTTER PIN (DD)

1/4" WASHER (P)

SPACER (LL)

5/64" HAIR

COTTER PIN (DD)

STEP 35: (SEE FIGURE 35)

• Attach the two suspension arms to the rear of the

clutch/idler assembly using two 5/16" x 3/4" hex bolts

(C), 5/16" washer (Q) and 5/16" nylock nuts (Y) for

each arm. Place the arms on the outside of the frame

with the notches to the rear.

• Insert a tensioning chain through the hole shown and

attach the end link to the spring on the lower idler arm.

FIGURE 35

5/16" x 3/4"

HEX BOLT (C)

5/16" NYLOCK

NUT (Y)

TENSIONING CHAIN (JJ)

5/16" WASHER (Q)

CABLE OPERATED MANUAL ATTACHMENT CLUTCH

FIGURE 37

HEX BOLTS

DRIVE BELT

FLAT IDLER

PULLEY

(#46989)

STEP 37: (SEE FIGURE 37)

• Two different length drive belts are included with

your snow thrower. Tractors with manual attachment

clutches and dual front deck suspension brackets use

the 55" drive belt with #46989 printed on the outside

of the belt. DO NOT USE the other belt.

STOP

Did you choose the correct drive belt for

your tractor? Using the wrong length belt

may cause premature bearing or belt failure.

• Slightly loosen the hex bolt next to the at idler pulley.

Install the drive belt down between the hex bolt and the

at idler pulley with the at side of the belt against the

pulley. Retighten the hex bolt.

• Loop the belt around the large v-pulley, placing it

between the v-pulley and the hex bolt next to the pulley.

19

FIGURE 40 VIEWED FROM UNDERNEATH

FIGURE 39

STEP 40: (SEE FIGURE 40)

• Assemble the short "V" belt onto the engine pulley

and then onto the large pulley on top of the clutch/idler

assembly. The belt must be placed to the inside of the

engine pulley keeper, the idler pulley and the keeper

bolt located beside the large pulley.

IMPORTANT: Do Not assemble the "V" belt around the

outside of the engine pulley keeper or the keeper bolt.

• Go to step 48 on page 22.

STEP 39: (SEE FIGURE 39)

• Remove the engine pulley keeper from the side of

the tractor frame by removing the washer and nut

that secure the keeper. Attach the new pulley keeper

supplied with the snow thrower, reusing the original

bolt, washer and nut.

NOTE: Some tractors may already be equipped with a

pulley keeper that is identical to the new one supplied.

• Attach the clutch/idler assembly to the tractor frame

as follows. Hook the assembly's notched arms onto

the two shoulder bolts you assembled to the inside

of the tractor frame. Lift the front of the assembly and

attach it to the R.H. and L.H. hanger brackets using

two pivot lock pins (GG) and 1/8" hairpin cotters (EE).

NEW ENGINE PULLEY KEEPER WITH

ORIGINAL BOLT, NUT AND WASHER

PIVOT LOCK PIN (GG)

(use second hole)

1/8" HAIRPIN COTTER (EE)

ENGINE

PULLEY

KEEPER BOLT

IDLER

PULLEY

ENGINE

PULLEY

KEEPER

Left Side

of Tractor

CLUTCH/IDLER ASSEMBLY

20

ELECTRIC ATTACHMENT CLUTCHES

FIGURE 42

TENSIONING CHAIN (JJ)

LEFT FRONT HOLE

FIGURE 43 VIEW OF BOTTOM

STEP 43: (SEE FIGURE 43)

• Hook the spring from the parts bag through the end of

the tensioning chain.

• Hook the other end of the spring onto the bottom of

the bolt and nut which secure the idler pulley to the

upper idler arm. Hold the bolt head and assemble a

3/8" hex lock nut (Z) onto the bolt, leaving enough

space for the spring to pivot freely between the two

nuts.

• Attach a 3/32" hairpin cotter (FF) to the chain, placing

it in the fth link from the spring.

CHAIN

(L.H. SIDE)

3/32" HAIR

COTTER PIN (FF)

5TH LINK

LEFT

SIDE

3/8" HEX

LOCK NUT (Z)

SPRING

RIGHT

SIDE

ATTACH

SPRING

HERE

STEP 44: (SEE TABLE 2)

• Two different length drive belts are included with

your snow thrower. Use the table below to select

the correct drive belt for your type tractor. The part

number is printed on the outside of the belt .

• Set aside the belt that is not for your tractor to avoid

accidentally using it.

55" BELT (PART #46989)

TRACTOR TYPE DECK SIZE CLUTCH TYPE

56" BELT (PART #48138)

TRACTOR TYPE DECK SIZE CLUTCH TYPE

(LT) Lawn Tractor 48" Electric

(LT) Lawn Tractor 38", 42", 46" Electric

TABLE 2

STEP 41: (SEE FIGURE 41)

• Attach the two suspension arms to the rear of the

clutch/idler assembly using two 5/16" x 3/4" hex bolts

(C), 5/16" washer (Q) and 5/16" nylock nuts (Y) for

each arm. Place the arms on the outside of the frame

with the notches to the rear.

• Insert a tensioning chain through the hole shown and

attach the end link to the spring on the lower idler arm.

FIGURE 41

STEP 42: (SEE FIGURE 42)

• Pace the extra tensioning chain (JJ) through the left

front hole in the clutch/idler assembly and then turn

the assembly upside down.

5/16" x 3/4"

HEX BOLT (C)

5/16" NYLOCK

NUT (Y)

TENSIONING CHAIN (JJ)

5/16" WASHER (Q)

La pagina sta caricando ...

McCulloch LST42C-669 Manuale del proprietario

McCulloch LST42C-669 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti