Canon imageFORMULA DR-C240 Manuale utente

Tipo
Manuale utente
This manual describes the setup and operating procedures for the
WA10 Network Adapter for the Canon imageFORMULA DR series.
To use this device, read this manual together with the instructions for
the scanner to be connected.
Procedures and Example Screens
This manual describes operations using Windows 7 as examples.
Table of Contents
Safety Precautions ..............................................................4
About This Device ...............................................................6
Setup.....................................................................................8
About Wi-Fi Connections..................................................10
Connecting Using the Wireless Settings
of the Computer .................................................................13
Selecting and Connecting to a Destination
Access Point ......................................................................15
Specifying and Connecting to an Access Point .............18
Connecting Using WPS.....................................................20
Connecting to Another Device with One-to-One
Connection.........................................................................21
Connecting to the Wired Network ....................................23
Scanning with the CaptureOnTouch Job Tool
from a Smart Device ..........................................................25
Scanning from a Computer with
the CaptureOnTouch Job Tool .........................................32
Using the Web Menu .........................................................37
Troubleshooting ................................................................43
Specifications ....................................................................45
WA10
User Manual
2
Trademarks
Canon and the Canon logo are registered trademarks of Canon Inc.
in the United States and may also be trademarks or registered
trademarks in other countries.
imageFORMULA is a trademark of CANON ELECTRONICS INC.
Microsoft and Windows are registered trademarks of Microsoft
Corporation in the United States and other countries.
Wi-Fi, Wi-Fi Alliance, the Wi-Fi CERTIFIED logo and the Wi-Fi
Protected Setup logo are registered trademarks of the Wi-Fi
Alliance.
Wi-Fi CERTIFIED, WPA, WPA2 and Wi-Fi Protected Setup are
trademarks of the Wi-Fi Alliance.
“WPS” in the settings, onscreen displays and in this manual
denotes Wi-Fi Protected Setup.
Other company names and product names in this manual are
registered trademarks or trademarks of each company.
Copyright
Copyright 2018 by CANON ELECTRONICS INC. All rights reserved.
No part of this publication may be reproduced or transmitted in any
form or by any means, electronic or mechanical, including
photocopying and recording, or by any information storage or retrieval
system without the prior written permission of CANON
ELECTRONICS INC.
Disclaimers
The information in this document is subject to change without notice.
CANON ELECTRONICS INC. MAKES NO WARRANTY OF ANY
KIND WITH REGARD TO THIS MATERIAL, EITHER EXPRESS OR
IMPLIED, EXPECT AS PROVIDED HEREIN, INCLUDING WITHOUT
LIMITATION, THEREOF, WARRANTIES AS TO MARKETABILITY,
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE
OF USE OR NON-INFRINGEMENT. CANON ELECTRONICS INC.
SHALL NOT BE LIABLE FOR ANY DIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR
EXPENSES RESULTING FROM THE USE OF THIS MATERIAL.
CANON ELECTRONICS INC. IS NOT LIABLE FOR THE STORAGE
AND HANDLING OF DOCUMENTS SCANNED WITH THIS
PRODUCT, OR THE STORAGE AND HANDLING OF RESULTING
SCANNED IMAGE DATA.
IF YOU INTEND TO DISCARD THE ORIGINALS OF SCANNED
DOCUMENTS, YOU THE CUSTOMER ARE RESPONSIBLE FOR
INSPECTING THE SCANNED IMAGES AND VERIFYING THAT
DATA IS INTACT.
THE MAXIMUM LIABILITY OF CANON ELECTRONICS INC.
UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE
OF THE PRODUCT COVERED BY THE WARRANTY.
FCC REGULATIONS (For North America)
Network Adapter, Model 6830020, 6830040
This device complies with Part 15 of FCC Rules and Industry Canada
licence-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may
cause undesired operation of this device.
Le présent appareil est conforme aux la partie 15 des règles de la
FCC et CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
This equipment complies with FCC/IC radiation exposure limits set
forth for an uncontrolled environment and meets the FCC radio
frequency (RF) Exposure Guidelines in Supplement C to OET65 and
RSS-102 of the IC radio frequency (RF) Exposure rules. This
equipment has very low levels of RF energy that it deemed to comply
without maximum permissive exposure evaluation (MPE). But it is
desirable that it should be installed and operated keeping the radiator
at least 20cm or more away from person's body (excluding
extremities: hands, wrists, feet and ankles).
Cet équipement est conforme aux limites d'exposition aux
rayonnements énoncées pour un environnement non contrôlé et
respecte les règles les radioélectriques (RF) de la FCC lignes
directrices d'exposition dans le Supplément C à OET65 et
d'exposition aux fréquences radioélectriques (RF) CNR-102 de l'IC.
Cet équipement émet une énergie RF très faible qui est considérée
conforme sans évaluation de l'exposition maximale autorisée.
Cependant, cet équipement doit être installé et utilisé en gardant une
distance de 20 cm ou plus entre le dispositif rayonnant et le corps (à
l'exception des extrémités : mains, poignets, pieds et chevilles).
3
FCC CAUTION
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the
equipment OFF and ON, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with Class B limits in
Subpart B of Part 15 of FCC Rules.
Do not make any changes or modifications to the equipment unless
otherwise specified in the manual. If such changes or modifications
should be made, you could be required to stop operation of the
equipment.
Canon U.S.A. Inc.
One Canon Park, Melville, NY 11747, U.S.A.
Tel. No. 1-800-OK-CANON (1-800-652-2666)
This transmitter must not be co-located or operated in conjunction with
any other antenna or transmitter.
AVERTISSEMENT
Ce produit émet un flux magnétique de faible niveau. Si vous utilisez
un stimulateur cardiaque ou pacemaker et éprouvez une sensation
inhabituelle, éloignez-vous de la machine et consultez votre médecin.
RADIO INTERFERENCE REGULATIONS (For 120 V
models)
This digital apparatus does not exceed the Class B limits for radio
noise emissions from digital apparatus as set out in the interference-
causing equipment standard entitled “Digital Apparatus”, ICES-003 of
the Industry Canada.
RÈGLEMENT SUR LE BROUILLAGE RADIOÉLECTRIQUE
(For 120 V models)
Cet appareil numérique respecte les limites de bruits radioélectriques
applicables aux appareils numériques de Classe B prescrites dans la
norme sur le matériel brouilleur: “Appareils Numériques”, NMB-003
édictée par l’Industrie Canada.
Für EMVG
Dieses Produkt ist zum Gebrauch im Wohnbereich, Geschäfts-und
Gewerbebereich sowie in Kleinbetrieben vorgesehen.
Model Names
The following names may be provided for the safety regulations in
each sales region of the Network Adapter.
WA10: Model 6830020, 6830040
4
Safety Precautions
About wireless communication
functions
This device incorporates wireless communication functions. The radio
waves used for wireless communication functions can affect medical
and other devices, which could cause serious accidents. Do not use
the wireless communication functions in the following conditions.
Do not use the wireless communication functions if you have a heart
pacemaker. The radio waves may affect pacemaker operation.
Do not use the wireless communication functions near persons
using medical devices like heart pacemakers. The radio waves may
affect pacemaker and similar devices’ operation. Contact the
appropriate medical institution before use.
Do not use the wireless communication functions inside medical
institutions such as hospitals, or near electronic medical equipment.
The radio waves may affect electronic medical equipment. Consult
with any medical institution before using it inside their facilities.
Do not use the wireless communication functions inside aircraft.
The radio waves may affect precision equipment in the aircraft, and
could cause a malfunction resulting in serious accident.
Do not use the wireless communication functions near
automatically controlled devices such as fire alarms. The radio
waves may affect such devices and could cause a malfunction
resulting in accident.
When using the wireless communication functions, keep this device
at least 20 cm from your body.
About the radio waves
This device operates in the 2.4 GHz frequency band (2.400 to 2.4835
GHz). Other users of these frequencies include products such as
microwave ovens, scientific and medical devices, similar Wi-Fi
stations, wireless intercom radio equipment for mobile device
identification used in industrial production lines (requiring licensing),
specific low-power radio stations that do not require licenses, amateur
radio stations and others (all afterwards called “other stations”). When
using, be aware of the following.
1. Before using this device, check whether other stations are
operating.
2. If radio frequency interference occurs between this device and
other stations, immediately relocate the device or stop using it (stop
transmitting).
After stopping, consult with your retailer or with our sales staff
regarding measures to avoid interference (e.g., partitioned
installation).
3. Otherwise, if troubles occur from radio frequency interference by
this device to other stations, consult with your retailer or our sales
staff.
European Union (and EEA) only.
This symbol indicates that this product is not to be
disposed of with your household waste, according to
the WEEE Directive (2002/96/EC) and your national
law. This product should be handed over to a
designated collection point, e.g., on an authorized
one-for-one basis when you buy a new similar product or to an
authorized collection site for recycling waste electrical and
electronic equipment (EEE). Improper handling of this type of
waste could have a possible negative impact on the environment
and human health due to potentially hazardous substances that
are generally associated with EEE. At the same time, your
cooperation in the correct disposal of this product will contribute
to the effective usage of natural resources. For more information
about where you can drop off your waste equipment for recycling,
please contact your local city office, waste authority, approved
WEEE scheme or your household waste disposal service. For
more information regarding return and recycling of WEEE
products, please visit www.canon-europe.com/environment
.
(EEA: Norway, Iceland and Liechtenstein)
5
Regional availability and limitations
Five versions of this product are provided for compliance with the various international wireless laws. The regions of availability for each version
are as follows. Please note that each version may be used only in its applicable country/region. For regions not included in the following list, contact
customer service.
Version
Name
Product
Code
Applicable Country/Region
Wireless LAN
Standard
Corresponding
Channels
Maximum
Wireless Output
WA10 JP
2999C001
3126C001
Japan
IEEE 802.11b/g/n
Channels 1 to 11
(2.412 to 2.462 GHz)
EIRP 11.48 dBm
WA10 USA
2999C002
3126C002
USA, Canada, Mexico, Brazil, Argentina,
Colombia, Peru, Panama
WA10 EU
2999C003
3126C003
Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, United
Kingdom, Iceland, Liechtenstein, Norway,
Switzerland, Turkey, Singapore, Vietnam,
Philippines, Indonesia, Malaysia, Thailand,
Chile, Russia, Australia, New Zealand, Hong
Kong
WA10 KR
2999C004
3126C004
Korea
WA10 INDIA
2999C005
3126C005
India
6
About This Device
This device allows you to connect LAN-compatible computers to a
scanner via a network. By connecting a scanner to the device with a
USB cable, you can perform scanning operations from a computer via
the network.
With a Wi-Fi connection, by connecting this device to a wireless base
station (access point) in the network environment, any computer in the
network can use the scanner. The device is very simple to connect if
the access point supports WPS (Wi-Fi Protected Setup).
Names of Parts
A Power button
Turns on this device. The power lamp lights blue when the device
turns on.
When the device’s power is on, press and hold this button to turn it
(and the power lamp) off.
Hint
When a scanner is connected, the device’s power will be linked to
the scanner and will turn on/off when the scanner turns on/off.
B WPS/Reset button
Press to connect with a WPS-compatible access point.
Hold this button while turning the device on, and keep holding until
it starts up, to return the device to its factory default state.
C Wireless On/Off button
Holding this button for five seconds switches between wired LAN
and Wi-Fi connection methods.
Hold this button while turning the device on, and keep holding until
it starts up, to set the network mode to AP mode.
D USB connector
Connect this device to the scanner using the USB cable.
E Power output connector
Use the supplied power relay cable to connect this to the scanner’s
power connector.
F LAN port (RJ-45)
For wired LAN connection, connect a network cable that supports
RJ-45 (10Base-T, 100Base-TX, or 1000Base-T).
G Power input connector
Connect the AC adapter supplied with the scanner here.
H Lamps
The following lamps indicate the device state.
1
2
3
4
A
B
C
D
E
F
G
H
Lamps Meaning
1
(Power Lamp)
Lit (blue) Power on
Unlit Power off
2 Wireless
Lit
(green)
Wireless LAN on
Unlit Wireless LAN off
7
3 Connection
Lit
(green)
Station mode: connecting
to the access point
See “Network modes
(p. 10)
DHCP setting on in wired
LAN mode
Lit (red) Initializing setup
Blinking
(green)
WPS executing
Blinking
(red)
WPS Error
Lit
(orange)
Starting up in AP mode
See “Network modes
(p. 10)
DHCP setting off in wired
LAN mode
Unlit Wireless LAN stopping
4Status
Lit
(green)
Transferring data
Lamps Meaning
8
Setup
(1) Installing the Scanner Driver
To use the device, the driver of the scanner to be used in conjunction
with the device must be updated to its latest version.
The scanner driver is available on the downloads page of the Canon
website. For details on acquiring and installing the driver, visit the
Canon support website.
http://www.canon-elec.co.jp/products/ims/softwareDownload/
index.html
Supported scanners
This unit supports the following scanners.
An update is required for scanner driver versions indicated above and
earlier. For details on how to acquire the latest scanner driver and the
latest information on supported models, visit the Canon support
website.
A special application is required to connect smart devices
(smartphones, tablet devices, etc.) to this device via Wi-Fi connection.
For details on acquiring and using this software, visit the Canon
support website.
(2) Connecting to the Scanner
A Connect the supplied USB cable to the USB ports on the device
and the scanner.
When connecting the device to a scanner that supports USB 3.0/
3.1, use the USB cable supplied with the scanner.
B Connect the supplied power relay cable to the power output
connector on the device and the power connector on the scanner.
C For wired LAN connection, plug the network cable's connector (RJ-
45) into the LAN port.
CAUTION
Hold the Wireless On/Off button for five seconds to switch the
device to wired LAN mode.
D Connect the AC adapter supplied with the scanner to the device,
and connect the power plug to a power outlet.
CAUTION
Connect and disconnect the AC adapter or power relay cables by
holding their plugs. Connecting and disconnecting by the cable may
result in damage to the cable.
Scanner Driver version
DR-C230 1.0.11705.08001 SP2
DR-C240 1.1.11508.3001 SP4
DR-M140 1.2.11407.1001 SP7
DR-M160II 1.2.11402.06001 SP7
DR-M260 1.0.11705.30001 SP4
DR-M1060 1.0.11402.20001 SP6
a
b
d
c
9
Cord Cover and Stand
You can attach the supplied cord cover to protect the connected
cable’s connector.
You can attach the stand to set the device upright. In addition, placing
the scanner on the stand will stabilize the device.
CAUTION
When connecting the device to a scanner equipped with a fan,
maintain a space of at least 10 mm between the device and the
scanner so as not to obstruct the vents. If you attached the device to
the stand and are placing the scanner on the stand, be sure to
position the device so that it does not obstruct the scanner’s vents.
When the stand is attached to the device, attach the cord cover as
well to prevent disconnection of the stand.
About Wi-Fi Connection Software
To establish a Wi-Fi connection, the WA10 Wireless Connection Tool
can be run from the bundled Setup disc.
System requirements
Supported operating systems:
Windows 7 Service Pack 1 or later
(32-bit and 64-bit editions)
Windows 8.1 (32-bit and 64-bit editions)
Windows 10 (32-bit and 64-bit editions)
Windows Server 2008 R2 SP1 (64-bit edition)
Windows Server 2012 R2 (64-bit edition)
Windows Server 2016 (64-bit edition)
Microsoft .NET Framework: 4.5.2 or later
This is the environment as of February 2018.
For the latest software support information, go to the Products page
on the Canon website.
Supported wireless standards: IEEE 802.11b/g/n
Place the
scanner here.
10
About Wi-Fi Connections
Connect the device to an access point or directly to a computer
according to the network environment.
Network modes
This device has the following two network modes.
To connect via Wi-Fi, set this device’s network mode to AP mode.
Using the WA10 Wireless Connection Tool to connect this device to
an access point sets the network mode to Station mode.
CAUTION
The device’s factory default setting is AP mode.
Running the WA10 Wireless Connection
Tool
IMPORTANT
Log on to Windows as an Administrator.
Close all other applications before running the software.
1
Insert the software setup disc into the computer’s disc
drive.
On the software setup disc, execute WA10WifiConnectionTool.exe.
CAUTION
The WA10 Wireless Connection Tool requires that .NET
Framework 4.5.2 or higher be installed. You can install it by
running NDP452-KB2901907-x86-x64-AllOS-ENU.exe on the
disc.
Hint
Click [Version Information] to display WA10 Wireless
Connection Tool version information.
Click [Environmental settings] - [Log settings] to display the [Log
File Settings] screen and collect log files.
Network mode Description
AP mode
This mode provides independent operation
without a separate wireless base station
(access point). It provides a one-to-one
connection to a computer.
Station mode
This mode provides wireless client
operation. In this mode, computers connect
to this device via a separate wireless access
point.
11
Enabling the wireless LAN function of
the computer
To make a Wi-Fi connection, turn on the computer’s wireless LAN function.
1
Click the Start button - [Control Panel] - [View network
status and tasks].
2
Click [Change adapter settings].
3
If the [Wireless Network Connection] icon is [Disabled],
double-click the icon.
4
Click to close the settings screen.
12
Connection Methods
IMPORTANT
The scanner can be shared with multiple computers on the same network via the access point, although only one can connect to the scanner at
a time.
When using a Wi-Fi connection, scanning is slower than with the USB connection.
Access Point Connection One-to-One Connection
Connect to this device
using the wireless settings
of the computer connected
to the access point.
See “Connecting Using
the Wireless Settings of
the Computer” (p. 13)
Select the access point
from the destination list for
this device’s connection.
See “Selecting and
Connecting to a
Destination Access Point”
(p. 15)
Configure the device
manually according to
your network environment.
See “Specifying and
Connecting to an Access
Point” (p. 18)
If the wireless access
point is WPS-compatible,
connection to the device
can be made using the
WPS feature.
See “Connecting Using
WPS” (p. 20)
Search for the device and
connect to it using your
computer’s wireless
connections feature.
See “Connecting to
Another Device with One-
to-One Connection”
(p. 21)
C
onnect using
t
he wireless
s
ettings of the
c
omputer
Copy Wi-Fi
connection settings
Select the
destination
access
point
Set
manually
Use WPS
13
Connecting Using the Wireless Settings of the Computer
Use the WA10 Wireless Connection Tool to automatically acquire the required network information from the wireless settings of the computer
connected to the wireless LAN access point, and connect the device to the same network.
CAUTION
If the access point is using security settings (such as MAC address filtering), change the settings to allow connection to this device.
To ensure good Wi-Fi communications, perform this procedure with the device initially located close to the access point.
1
If the device is powered on, turn it off.
Turning off the scanner also turns off the device.
2
Enable the wireless LAN function of the computer.
For details, see “Enabling the wireless LAN function of the
computer” (p. 11).
This step is not necessary if the wireless LAN function is already
enabled. Skip to step 3.
3
Run the WA10 Wireless Connection Tool.
On the software setup disc, execute WA10WifiConnectionTool.exe
(
p. 10
).
4
Click [Start].
5
Hold the Wireless On/Off button while turning the device
on to start it up in AP mode.
Turning on the scanner also turns on the device.
Hold the Wireless On/Off button until the Connection lamp lights
orange.
CAUTION
The device’s factory default setting is AP mode.
Wireless On/Off button
Power button
Connection lamp
14
6
Click [Next].
7
Select the device to configure, and click [Next].
8
Select [Setup by using the computer’s wireless settings],
and click [Next].
The connection is established.
When successfully connected, “Success” is displayed on the
result screen. This completes configuration.
Hint
When normal connection fails, “Failed” is displayed on the result
screen. To reconfigure, click [Return to main screen] and retry the
operation from the beginning.
15
Selecting and Connecting to a Destination Access Point
Using the WA10 Wireless Connection Tool, select the access point from the destination list, and connect this device to the network.
CAUTION
If the access point is using security settings (such as MAC address filtering), change the settings to allow connection to this device.
To ensure good Wi-Fi communications, perform this procedure with the device initially located close to the access point.
1
If the device is powered on, turn it off.
Turning off the scanner also turns off the device.
2
Enable the wireless LAN function of the computer.
For details, see “Enabling the wireless LAN function of the
computer” (p. 11).
This step is not necessary if the wireless LAN function is already
enabled. Skip to step 3.
3
Run the WA10 Wireless Connection Tool.
On the software setup disc, execute WA10WifiConnectionTool.exe
(
p. 10
).
4
Click [Start].
5
Hold the Wireless On/Off button while turning the device
on to start it up in AP mode.
Turning on the scanner also turns on the device.
Hold the Wireless On/Off button until the Connection lamp lights
orange.
CAUTION
The device’s factory default setting is AP mode.
Wireless On/Off button
Power button
Connection lamp
16
6
Click [Next].
7
Select the device to configure, and click [Next].
8
Select [Setup by selecting from list], and click [Next].
A list of access points detected by the computer is displayed.
9
From the list, select the access point to connect to, and
click [Next].
17
10
Enter the security key for the access point, and click
[Next].
The connection is established.
When successfully connected, “Success” is displayed on the
result screen. This completes configuration.
Hint
When normal connection fails, “Failed” is displayed on the result
screen. To reconfigure, click [Return to main screen] and retry the
operation from the beginning.
18
Specifying and Connecting to an Access Point
Using the WA10 Wireless Connection Tool, specify the access point for connection, then connect this device to the network.
CAUTION
If the access point is using security settings (such as MAC address filtering), change the settings to allow connection to this device.
To ensure good Wi-Fi communications, perform this procedure with the device initially located close to the access point.
1
If the device is powered on, turn it off.
Turning off the scanner also turns off the device.
2
Enable the wireless LAN function of the computer.
For details, see “Enabling the wireless LAN function of the
computer” (p. 11).
This step is not necessary if the wireless LAN function is already
enabled. Skip to step 3.
3
Run the WA10 Wireless Connection Tool.
On the software setup disc, execute WA10WifiConnectionTool.exe
(
p. 10
).
4
Click [Start].
5
Hold the Wireless On/Off button while turning the device
on to start it up in AP mode.
Turning on the scanner also turns on the device.
Hold the Wireless On/Off button until the Connection lamp lights
orange.
CAUTION
The device’s factory default setting is AP mode.
Wireless On/Off button
Power button
Connection lamp
19
6
Click [Next].
7
Select the device to configure, and click [Next].
8
Select [Others], and click [Next].
9
Enter the information for the access point to be
connected.
A Enter the SSID.
B Select the type of security.
C Enter the security key.
10
Click [Next].
The connection is established.
When successfully connected, “Success” is displayed on the
result screen. This completes configuration.
Hint
When normal connection fails, “Failed” is displayed on the result
screen. To reconfigure, click [Return to main screen] and retry the
operation from the beginning.
20
Connecting Using WPS
Using WPS, this device can connect to an existing wireless network having a WPS-equipped access point.
CAUTION
Even a WPS-equipped access point may have WPS disabled. Ensure WPS is enabled.
If the access point is using security settings (such as MAC address filtering), change the settings to allow connection to this device.
To ensure good Wi-Fi communications, perform this procedure with the device initially located close to the access point.
1
If the device is powered on, turn it off.
Turning off the scanner also turns off the device.
2
Enable the wireless LAN function of the computer.
For details, see “Enabling the wireless LAN function of the
computer” (p. 11).
This step is not necessary if the wireless LAN function is already
enabled. Skip to step 3.
3
Hold the Wireless On/Off button while turning the device
on to start it up in AP mode.
Turning on the scanner also turns on the device.
Hold the Wireless On/Off button until the Connection lamp lights
orange.
CAUTION
The device’s factory default setting is AP mode.
4
Press the WPS button on the access point to activate the
connection-waiting state.
See the instructions for your access point.
CAUTION
This device cannot connect if the connection-waiting state is
activated on multiple access points at the same time.
5
Hold this device’s WPS/Reset button until the Connection
lamp blinks green (about five seconds).
The device communicates with the waiting access point to acquire
and automatically configure the required Wi-Fi settings. When the
settings are configured, the Connection lamp lights steadily
(green).
CAUTION
If a WPS error occurs and connection to the access point fails, the
Connection lamp blinks red.
Wireless On/Off button
Power button
Connection lamp
WPS/Reset button
Connection lamp
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51

Canon imageFORMULA DR-C240 Manuale utente

Tipo
Manuale utente

in altre lingue