Canon imageFORMULA DR-M260 Manuale utente

This manual describes the setup and operating procedures for the

WA10 Network Adapter for the Canon imageFORMULA DR series.

To use this device, read this manual together with the instructions for

the scanner to be connected.

Procedures and Example Screens

This manual describes operations using Windows 7 as examples.

Table of Contents

Safety Precautions ..............................................................4

About This Device ...............................................................6

Setup.....................................................................................8

About Wi-Fi Connections..................................................10

Connecting Using the Wireless Settings

of the Computer .................................................................13

Selecting and Connecting to a Destination

Access Point ......................................................................15

Specifying and Connecting to an Access Point .............18

Connecting Using WPS.....................................................20

Connecting to Another Device with One-to-One

Connection.........................................................................21

Connecting to the Wired Network ....................................23

Scanning with the CaptureOnTouch Job Tool

from a Smart Device ..........................................................25

Scanning from a Computer with

the CaptureOnTouch Job Tool .........................................32

Using the Web Menu .........................................................37

Troubleshooting ................................................................43

Specifications ....................................................................45

WA10

User Manual

2

Trademarks

● Canon and the Canon logo are registered trademarks of Canon Inc.

in the United States and may also be trademarks or registered

trademarks in other countries.

● imageFORMULA is a trademark of CANON ELECTRONICS INC.

● Microsoft and Windows are registered trademarks of Microsoft

Corporation in the United States and other countries.

● Wi-Fi, Wi-Fi Alliance, the Wi-Fi CERTIFIED logo and the Wi-Fi

Protected Setup logo are registered trademarks of the Wi-Fi

Alliance.

● Wi-Fi CERTIFIED, WPA, WPA2 and Wi-Fi Protected Setup are

trademarks of the Wi-Fi Alliance.

● “WPS” in the settings, onscreen displays and in this manual

denotes Wi-Fi Protected Setup.

● Other company names and product names in this manual are

registered trademarks or trademarks of each company.

Copyright

No part of this publication may be reproduced or transmitted in any

form or by any means, electronic or mechanical, including

photocopying and recording, or by any information storage or retrieval

system without the prior written permission of CANON

ELECTRONICS INC.

Disclaimers

The information in this document is subject to change without notice.

CANON ELECTRONICS INC. MAKES NO WARRANTY OF ANY

KIND WITH REGARD TO THIS MATERIAL, EITHER EXPRESS OR

IMPLIED, EXPECT AS PROVIDED HEREIN, INCLUDING WITHOUT

LIMITATION, THEREOF, WARRANTIES AS TO MARKETABILITY,

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE

OF USE OR NON-INFRINGEMENT. CANON ELECTRONICS INC.

SHALL NOT BE LIABLE FOR ANY DIRECT, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES OF ANY NATURE, OR LOSSES OR

EXPENSES RESULTING FROM THE USE OF THIS MATERIAL.

CANON ELECTRONICS INC. IS NOT LIABLE FOR THE STORAGE

AND HANDLING OF DOCUMENTS SCANNED WITH THIS

PRODUCT, OR THE STORAGE AND HANDLING OF RESULTING

SCANNED IMAGE DATA.

IF YOU INTEND TO DISCARD THE ORIGINALS OF SCANNED

DOCUMENTS, YOU THE CUSTOMER ARE RESPONSIBLE FOR

INSPECTING THE SCANNED IMAGES AND VERIFYING THAT

DATA IS INTACT.

THE MAXIMUM LIABILITY OF CANON ELECTRONICS INC.

UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE

OF THE PRODUCT COVERED BY THE WARRANTY.

FCC REGULATIONS (For North America)

Network Adapter, Model 6830020, 6830040

This device complies with Part 15 of FCC Rules and Industry Canada

licence-exempt RSS standard(s). Operation is subject to the following

two conditions: (1) this device may not cause interference, and (2) this

device must accept any interference, including interference that may

cause undesired operation of this device.

Le présent appareil est conforme aux la partie 15 des règles de la

FCC et CNR d'Industrie Canada applicables aux appareils radio

exempts de licence. L'exploitation est autorisée aux deux conditions

suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)

l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique

subi, même si le brouillage est susceptible d'en compromettre le

fonctionnement.

This equipment complies with FCC/IC radiation exposure limits set

forth for an uncontrolled environment and meets the FCC radio

frequency (RF) Exposure Guidelines in Supplement C to OET65 and

RSS-102 of the IC radio frequency (RF) Exposure rules. This

equipment has very low levels of RF energy that it deemed to comply

without maximum permissive exposure evaluation (MPE). But it is

desirable that it should be installed and operated keeping the radiator

at least 20cm or more away from person's body (excluding

extremities: hands, wrists, feet and ankles).

Cet équipement est conforme aux limites d'exposition aux

rayonnements énoncées pour un environnement non contrôlé et

respecte les règles les radioélectriques (RF) de la FCC lignes

directrices d'exposition dans le Supplément C à OET65 et

d'exposition aux fréquences radioélectriques (RF) CNR-102 de l'IC.

Cet équipement émet une énergie RF très faible qui est considérée

conforme sans évaluation de l'exposition maximale autorisée.

Cependant, cet équipement doit être installé et utilisé en gardant une

distance de 20 cm ou plus entre le dispositif rayonnant et le corps (à

l'exception des extrémités : mains, poignets, pieds et chevilles).

3

FCC CAUTION

Changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate

the equipment.

Note: This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the

equipment OFF and ON, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cable is required to comply with Class B limits in

Subpart B of Part 15 of FCC Rules.

Do not make any changes or modifications to the equipment unless

otherwise specified in the manual. If such changes or modifications

should be made, you could be required to stop operation of the

equipment.

Canon U.S.A. Inc.

One Canon Park, Melville, NY 11747, U.S.A.

Tel. No. 1-800-OK-CANON (1-800-652-2666)

This transmitter must not be co-located or operated in conjunction with

any other antenna or transmitter.

AVERTISSEMENT

Ce produit émet un flux magnétique de faible niveau. Si vous utilisez

un stimulateur cardiaque ou pacemaker et éprouvez une sensation

inhabituelle, éloignez-vous de la machine et consultez votre médecin.

RADIO INTERFERENCE REGULATIONS (For 120 V

models)

This digital apparatus does not exceed the Class B limits for radio

noise emissions from digital apparatus as set out in the interference-

causing equipment standard entitled “Digital Apparatus”, ICES-003 of

the Industry Canada.

RÈGLEMENT SUR LE BROUILLAGE RADIOÉLECTRIQUE

(For 120 V models)

Cet appareil numérique respecte les limites de bruits radioélectriques

applicables aux appareils numériques de Classe B prescrites dans la

norme sur le matériel brouilleur: “Appareils Numériques”, NMB-003

édictée par l’Industrie Canada.

Für EMVG

Dieses Produkt ist zum Gebrauch im Wohnbereich, Geschäfts-und

Gewerbebereich sowie in Kleinbetrieben vorgesehen.

Model Names

The following names may be provided for the safety regulations in

each sales region of the Network Adapter.

WA10: Model 6830020, 6830040

4

Safety Precautions

About wireless communication

functions

This device incorporates wireless communication functions. The radio

waves used for wireless communication functions can affect medical

and other devices, which could cause serious accidents. Do not use

the wireless communication functions in the following conditions.

● Do not use the wireless communication functions if you have a heart

pacemaker. The radio waves may affect pacemaker operation.

● Do not use the wireless communication functions near persons

using medical devices like heart pacemakers. The radio waves may

affect pacemaker and similar devices’ operation. Contact the

appropriate medical institution before use.

● Do not use the wireless communication functions inside medical

institutions such as hospitals, or near electronic medical equipment.

The radio waves may affect electronic medical equipment. Consult

with any medical institution before using it inside their facilities.

● Do not use the wireless communication functions inside aircraft.

The radio waves may affect precision equipment in the aircraft, and

could cause a malfunction resulting in serious accident.

● Do not use the wireless communication functions near

automatically controlled devices such as fire alarms. The radio

waves may affect such devices and could cause a malfunction

resulting in accident.

● When using the wireless communication functions, keep this device

at least 20 cm from your body.

About the radio waves

This device operates in the 2.4 GHz frequency band (2.400 to 2.4835

GHz). Other users of these frequencies include products such as

microwave ovens, scientific and medical devices, similar Wi-Fi

stations, wireless intercom radio equipment for mobile device

identification used in industrial production lines (requiring licensing),

specific low-power radio stations that do not require licenses, amateur

radio stations and others (all afterwards called “other stations”). When

using, be aware of the following.

1. Before using this device, check whether other stations are

operating.

2. If radio frequency interference occurs between this device and

other stations, immediately relocate the device or stop using it (stop

transmitting).

After stopping, consult with your retailer or with our sales staff

regarding measures to avoid interference (e.g., partitioned

installation).

3. Otherwise, if troubles occur from radio frequency interference by

this device to other stations, consult with your retailer or our sales

staff.

European Union (and EEA) only.

This symbol indicates that this product is not to be

disposed of with your household waste, according to

the WEEE Directive (2002/96/EC) and your national

law. This product should be handed over to a

designated collection point, e.g., on an authorized

one-for-one basis when you buy a new similar product or to an

authorized collection site for recycling waste electrical and

electronic equipment (EEE). Improper handling of this type of

waste could have a possible negative impact on the environment

and human health due to potentially hazardous substances that

are generally associated with EEE. At the same time, your

cooperation in the correct disposal of this product will contribute

to the effective usage of natural resources. For more information

about where you can drop off your waste equipment for recycling,

please contact your local city office, waste authority, approved

WEEE scheme or your household waste disposal service. For

more information regarding return and recycling of WEEE

products, please visit www.canon-europe.com/environment

.

(EEA: Norway, Iceland and Liechtenstein)

5

Regional availability and limitations

Five versions of this product are provided for compliance with the various international wireless laws. The regions of availability for each version

are as follows. Please note that each version may be used only in its applicable country/region. For regions not included in the following list, contact

customer service.

Version

Name

Product

Code

Applicable Country/Region

Wireless LAN

Standard

Corresponding

Channels

Maximum

Wireless Output

WA10 JP

2999C001

3126C001

Japan

IEEE 802.11b/g/n

Channels 1 to 11

(2.412 to 2.462 GHz)

EIRP 11.48 dBm

WA10 USA

2999C002

3126C002

USA, Canada, Mexico, Brazil, Argentina,

Colombia, Peru, Panama

WA10 EU

2999C003

3126C003

Austria, Belgium, Bulgaria, Cyprus, Czech

Republic, Denmark, Estonia, Finland, France,

Germany, Greece, Hungary, Ireland, Italy,

Latvia, Lithuania, Luxembourg, Malta,

Netherlands, Poland, Portugal, Romania,

Slovakia, Slovenia, Spain, Sweden, United

Kingdom, Iceland, Liechtenstein, Norway,

Switzerland, Turkey, Singapore, Vietnam,

Philippines, Indonesia, Malaysia, Thailand,

Chile, Russia, Australia, New Zealand, Hong

Kong

WA10 KR

2999C004

3126C004

Korea

WA10 INDIA

2999C005

3126C005

India

6

About This Device

This device allows you to connect LAN-compatible computers to a

scanner via a network. By connecting a scanner to the device with a

USB cable, you can perform scanning operations from a computer via

the network.

With a Wi-Fi connection, by connecting this device to a wireless base

station (access point) in the network environment, any computer in the

network can use the scanner. The device is very simple to connect if

the access point supports WPS (Wi-Fi Protected Setup).

Names of Parts

A Power button

Turns on this device. The power lamp lights blue when the device

turns on.

When the device’s power is on, press and hold this button to turn it

(and the power lamp) off.

Hint

When a scanner is connected, the device’s power will be linked to

the scanner and will turn on/off when the scanner turns on/off.

B WPS/Reset button

Press to connect with a WPS-compatible access point.

Hold this button while turning the device on, and keep holding until

it starts up, to return the device to its factory default state.

C Wireless On/Off button

Holding this button for five seconds switches between wired LAN

and Wi-Fi connection methods.

Hold this button while turning the device on, and keep holding until

it starts up, to set the network mode to AP mode.

D USB connector

Connect this device to the scanner using the USB cable.

E Power output connector

Use the supplied power relay cable to connect this to the scanner’s

power connector.

F LAN port (RJ-45)

For wired LAN connection, connect a network cable that supports

RJ-45 (10Base-T, 100Base-TX, or 1000Base-T).

G Power input connector

Connect the AC adapter supplied with the scanner here.

H Lamps

The following lamps indicate the device state.

1

2

3

4

A

B

C

D

E

F

G

H

Lamps Meaning

1

(Power Lamp)

Lit (blue) Power on

Unlit Power off

2 Wireless

Lit

(green)

Wireless LAN on

Unlit Wireless LAN off

7

3 Connection

Lit

(green)

Station mode: connecting

to the access point

See “Network modes”

(p. 10)

DHCP setting on in wired

LAN mode

Lit (red) Initializing setup

Blinking

(green)

WPS executing

Blinking

(red)

WPS Error

Lit

(orange)

Starting up in AP mode

See “Network modes”

(p. 10)

DHCP setting off in wired

LAN mode

Unlit Wireless LAN stopping

4Status

Lit

(green)

Transferring data

Lamps Meaning

8

Setup

(1) Installing the Scanner Driver

To use the device, the driver of the scanner to be used in conjunction

with the device must be updated to its latest version.

The scanner driver is available on the downloads page of the Canon

website. For details on acquiring and installing the driver, visit the

Canon support website.

http://www.canon-elec.co.jp/products/ims/softwareDownload/

index.html

Supported scanners

This unit supports the following scanners.

An update is required for scanner driver versions indicated above and

earlier. For details on how to acquire the latest scanner driver and the

latest information on supported models, visit the Canon support

website.

A special application is required to connect smart devices

(smartphones, tablet devices, etc.) to this device via Wi-Fi connection.

For details on acquiring and using this software, visit the Canon

support website.

(2) Connecting to the Scanner

A Connect the supplied USB cable to the USB ports on the device

and the scanner.

When connecting the device to a scanner that supports USB 3.0/

3.1, use the USB cable supplied with the scanner.

B Connect the supplied power relay cable to the power output

connector on the device and the power connector on the scanner.

C For wired LAN connection, plug the network cable's connector (RJ-

45) into the LAN port.

CAUTION

Hold the Wireless On/Off button for five seconds to switch the

device to wired LAN mode.

D Connect the AC adapter supplied with the scanner to the device,

and connect the power plug to a power outlet.

CAUTION

Connect and disconnect the AC adapter or power relay cables by

holding their plugs. Connecting and disconnecting by the cable may

result in damage to the cable.

Scanner Driver version

DR-C230 1.0.11705.08001 SP2

DR-C240 1.1.11508.3001 SP4

DR-M140 1.2.11407.1001 SP7

DR-M160II 1.2.11402.06001 SP7

DR-M260 1.0.11705.30001 SP4

DR-M1060 1.0.11402.20001 SP6

a

b

d

c

9

Cord Cover and Stand

You can attach the supplied cord cover to protect the connected

cable’s connector.

You can attach the stand to set the device upright. In addition, placing

the scanner on the stand will stabilize the device.

CAUTION

• When connecting the device to a scanner equipped with a fan,

maintain a space of at least 10 mm between the device and the

scanner so as not to obstruct the vents. If you attached the device to

the stand and are placing the scanner on the stand, be sure to

position the device so that it does not obstruct the scanner’s vents.

• When the stand is attached to the device, attach the cord cover as

well to prevent disconnection of the stand.

About Wi-Fi Connection Software

To establish a Wi-Fi connection, the WA10 Wireless Connection Tool

can be run from the bundled Setup disc.

System requirements

Supported operating systems:

Windows 7 Service Pack 1 or later

(32-bit and 64-bit editions)

Windows 8.1 (32-bit and 64-bit editions)

Windows 10 (32-bit and 64-bit editions)

Windows Server 2008 R2 SP1 (64-bit edition)

Windows Server 2012 R2 (64-bit edition)

Windows Server 2016 (64-bit edition)

Microsoft .NET Framework: 4.5.2 or later

This is the environment as of February 2018.

For the latest software support information, go to the Products page

on the Canon website.

Supported wireless standards: IEEE 802.11b/g/n

Place the

scanner here.

10

About Wi-Fi Connections

Connect the device to an access point or directly to a computer

according to the network environment.

Network modes

This device has the following two network modes.

To connect via Wi-Fi, set this device’s network mode to AP mode.

Using the WA10 Wireless Connection Tool to connect this device to

an access point sets the network mode to Station mode.

CAUTION

The device’s factory default setting is AP mode.

Running the WA10 Wireless Connection

Tool

IMPORTANT

• Log on to Windows as an Administrator.

• Close all other applications before running the software.

1

Insert the software setup disc into the computer’s disc

drive.

On the software setup disc, execute WA10WifiConnectionTool.exe.

CAUTION

The WA10 Wireless Connection Tool requires that .NET

Framework 4.5.2 or higher be installed. You can install it by

running NDP452-KB2901907-x86-x64-AllOS-ENU.exe on the

disc.

Hint

• Click [Version Information] to display WA10 Wireless

Connection Tool version information.

• Click [Environmental settings] - [Log settings] to display the [Log

File Settings] screen and collect log files.

Network mode Description

AP mode

This mode provides independent operation

without a separate wireless base station

(access point). It provides a one-to-one

connection to a computer.

Station mode

This mode provides wireless client

operation. In this mode, computers connect

to this device via a separate wireless access

point.

11

Enabling the wireless LAN function of

the computer

To make a Wi-Fi connection, turn on the computer’s wireless LAN function.

1

Click the Start button - [Control Panel] - [View network

status and tasks].

2

Click [Change adapter settings].

3

If the [Wireless Network Connection] icon is [Disabled],

double-click the icon.

4

Click to close the settings screen.

12

Connection Methods

IMPORTANT

• The scanner can be shared with multiple computers on the same network via the access point, although only one can connect to the scanner at

a time.

• When using a Wi-Fi connection, scanning is slower than with the USB connection.

Access Point Connection One-to-One Connection

Connect to this device

using the wireless settings

of the computer connected

to the access point.

➔ See “Connecting Using

the Wireless Settings of

the Computer” (p. 13)

Select the access point

from the destination list for

this device’s connection.

➔ See “Selecting and

Connecting to a

Destination Access Point”

(p. 15)

Configure the device

manually according to

your network environment.

➔ See “Specifying and

Connecting to an Access

Point” (p. 18)

If the wireless access

point is WPS-compatible,

connection to the device

can be made using the

WPS feature.

➔ See “Connecting Using

WPS” (p. 20)

Search for the device and

connect to it using your

computer’s wireless

connections feature.

➔ See “Connecting to

Another Device with One-

to-One Connection”

(p. 21)

C

onnect using

t

he wireless

s

ettings of the

c

omputer

Copy Wi-Fi

connection settings

Select the

destination

access

point

Set

manually

Use WPS

13

Connecting Using the Wireless Settings of the Computer

Use the WA10 Wireless Connection Tool to automatically acquire the required network information from the wireless settings of the computer

connected to the wireless LAN access point, and connect the device to the same network.

CAUTION

• If the access point is using security settings (such as MAC address filtering), change the settings to allow connection to this device.

• To ensure good Wi-Fi communications, perform this procedure with the device initially located close to the access point.

1

If the device is powered on, turn it off.

Turning off the scanner also turns off the device.

2

Enable the wireless LAN function of the computer.

For details, see “Enabling the wireless LAN function of the

computer” (p. 11).

This step is not necessary if the wireless LAN function is already

enabled. Skip to step 3.

3

Run the WA10 Wireless Connection Tool.

On the software setup disc, execute WA10WifiConnectionTool.exe

(

p. 10

).

4

Click [Start].

5

Hold the Wireless On/Off button while turning the device

on to start it up in AP mode.

Turning on the scanner also turns on the device.

Hold the Wireless On/Off button until the Connection lamp lights

orange.

CAUTION

The device’s factory default setting is AP mode.

Wireless On/Off button

Power button

Connection lamp

14

6

Click [Next].

7

Select the device to configure, and click [Next].

8

Select [Setup by using the computer’s wireless settings],

and click [Next].

The connection is established.

When successfully connected, “Success” is displayed on the

result screen. This completes configuration.

Hint

When normal connection fails, “Failed” is displayed on the result

screen. To reconfigure, click [Return to main screen] and retry the

operation from the beginning.

15

Selecting and Connecting to a Destination Access Point

Using the WA10 Wireless Connection Tool, select the access point from the destination list, and connect this device to the network.

CAUTION

• If the access point is using security settings (such as MAC address filtering), change the settings to allow connection to this device.

• To ensure good Wi-Fi communications, perform this procedure with the device initially located close to the access point.

1

If the device is powered on, turn it off.

Turning off the scanner also turns off the device.

2

Enable the wireless LAN function of the computer.

For details, see “Enabling the wireless LAN function of the

computer” (p. 11).

This step is not necessary if the wireless LAN function is already

enabled. Skip to step 3.

3

Run the WA10 Wireless Connection Tool.

On the software setup disc, execute WA10WifiConnectionTool.exe

(

p. 10

).

4

Click [Start].

5

Hold the Wireless On/Off button while turning the device

on to start it up in AP mode.

Turning on the scanner also turns on the device.

Hold the Wireless On/Off button until the Connection lamp lights

orange.

CAUTION

The device’s factory default setting is AP mode.

Wireless On/Off button

Power button

Connection lamp

16

6

Click [Next].

7

Select the device to configure, and click [Next].

8

Select [Setup by selecting from list], and click [Next].

A list of access points detected by the computer is displayed.

9

From the list, select the access point to connect to, and

click [Next].

17

10

Enter the security key for the access point, and click

[Next].

The connection is established.

When successfully connected, “Success” is displayed on the

result screen. This completes configuration.

Hint

When normal connection fails, “Failed” is displayed on the result

screen. To reconfigure, click [Return to main screen] and retry the

operation from the beginning.

18

Specifying and Connecting to an Access Point

Using the WA10 Wireless Connection Tool, specify the access point for connection, then connect this device to the network.

CAUTION

• If the access point is using security settings (such as MAC address filtering), change the settings to allow connection to this device.

• To ensure good Wi-Fi communications, perform this procedure with the device initially located close to the access point.

1

If the device is powered on, turn it off.

Turning off the scanner also turns off the device.

2

Enable the wireless LAN function of the computer.

For details, see “Enabling the wireless LAN function of the

computer” (p. 11).

This step is not necessary if the wireless LAN function is already

enabled. Skip to step 3.

3

Run the WA10 Wireless Connection Tool.

On the software setup disc, execute WA10WifiConnectionTool.exe

(

p. 10

).

4

Click [Start].

5

Hold the Wireless On/Off button while turning the device

on to start it up in AP mode.

Turning on the scanner also turns on the device.

Hold the Wireless On/Off button until the Connection lamp lights

orange.

CAUTION

The device’s factory default setting is AP mode.

Wireless On/Off button

Power button

Connection lamp

19

6

Click [Next].

7

Select the device to configure, and click [Next].

8

Select [Others], and click [Next].

9

Enter the information for the access point to be

connected.

A Enter the SSID.

B Select the type of security.

C Enter the security key.

10

Click [Next].

The connection is established.

When successfully connected, “Success” is displayed on the

result screen. This completes configuration.

Hint

When normal connection fails, “Failed” is displayed on the result

screen. To reconfigure, click [Return to main screen] and retry the

operation from the beginning.

20

Connecting Using WPS

Using WPS, this device can connect to an existing wireless network having a WPS-equipped access point.

CAUTION

• Even a WPS-equipped access point may have WPS disabled. Ensure WPS is enabled.

• If the access point is using security settings (such as MAC address filtering), change the settings to allow connection to this device.

• To ensure good Wi-Fi communications, perform this procedure with the device initially located close to the access point.

1

If the device is powered on, turn it off.

Turning off the scanner also turns off the device.

2

Enable the wireless LAN function of the computer.

For details, see “Enabling the wireless LAN function of the

computer” (p. 11).

This step is not necessary if the wireless LAN function is already

enabled. Skip to step 3.

3

Hold the Wireless On/Off button while turning the device

on to start it up in AP mode.

Turning on the scanner also turns on the device.

Hold the Wireless On/Off button until the Connection lamp lights

orange.

CAUTION

The device’s factory default setting is AP mode.

4

Press the WPS button on the access point to activate the

connection-waiting state.

See the instructions for your access point.

CAUTION

This device cannot connect if the connection-waiting state is

activated on multiple access points at the same time.

5

Hold this device’s WPS/Reset button until the Connection

lamp blinks green (about five seconds).

The device communicates with the waiting access point to acquire

and automatically configure the required Wi-Fi settings. When the

settings are configured, the Connection lamp lights steadily

(green).

CAUTION

If a WPS error occurs and connection to the access point fails, the

Connection lamp blinks red.

Wireless On/Off button

Power button

Connection lamp

WPS/Reset button

Connection lamp

La pagina sta caricando ...

Canon imageFORMULA DR-M260 Manuale utente

Questo manuale è adatto anche per

Canon imageFORMULA DR-M260 Manuale utente

in altre lingue

Documenti correlati

Altri documenti