ACV Control Unit THETA Istruzioni per l'uso

Tipo
Istruzioni per l'uso
For more information see Operating Instructions -
Temperature settings
Operating instructions summary
for standard unit and boiler control panel
For more information see Operating Instructions -
Special operating modes - Manual mode
Operation and and symbols Geral functions
With the combination knob values are selected, parameters
modified and, by pressing the knob they are memorized.
Turn to the right (+): increase values
Turn to the left (–): decrease values
Press once: Acceptance of the selected and indi-
cated value
K
eep pr
essed: Entry into the programming level,
re-entry into the previous selection
3 sec
Standard display
Weekday, date, time, boiler
temperature
The current operational mode
is indicated by an arrow poin-
ting to the appertaining symbol
63.5
16:32
MO. 22. AUG.;05
°C
À
63.5
16:32
MO. 22. AUG.;05
°C
Sun shade symbol:
Summer mode is activated
(heating switched off, hot-water
according to timer-program)
Frost cristal symbol:
Frost protection mode is
activated
Á
63.5
16:32
MO. 22. AUG.;05
°C
Affichages spéciaux
50-4
EjjOR
HEAT.GEN
Error message (example)
appears alternating with
standard display
Call heating specialist!
-72.5
0058. 5
MANUAL
°C
°C
keep pressed for approx. 5 seconds
Manual mode (adjust boiler temperature)
required boiler temperature
boiler temperature
modify
temperature
return to previous operational mode
For more information see Operating Instructions -
Temperature settings
Heating curves
The adjustment of the heating curve is dependent of the
plant installation and shows the relation between the outside
temperature and the heating water temperature.
Recommended setting values:
The calculation of the required heating energy is based on
the coldest avarage outdoor temperature and can be reque-
sted from the heating specialist.
Setting the heating curve
For more information see Operating Instructions -
Setting the heating characteristics.
50.0
DAY
DHW
°C
setting range: 10°C to DHW-max.
Setting the required hot-water temperature
setting range: 5.0 to 30 °C
20.0
ROOM-DAY
°C
Setting the required daytime temperature
accept
Note:
For separated control mode the relevant heating circuit must be
selected first before setting daytime or set-back temperature!
setting range: 5.0 to 30 °C
16.0
ROOM-NIGHT
°C
Setting the required set back temperature
Heating system
-12°C -15°C -18°C
Underfloor 1.10 1.00 0.90
Radiator 1.70 1.55 1.45
Convector 2.20 2.00 1.85
modify
temperature
modify
temperature
accept
modify
temperature
coldest outside temperature (regional)
select
heating circuit
1.50
HC
HEAT.CURVE
confirm selected circuit
1.50
HC
HEAT.CURVE
room temp. too warm: decrease slope
room temp. too cold: increase slope
modify
slope
store modification
terminate (exit to standard display)
Modify next heating circuit(s) in the same way, if necessary.
Attention! Alter only in small steps and in intervalls of 0.1
every 1 or 2 days. Thermostatic radiator valves
should almost be opened fully.
accept
HC
= direct circuit / MC1= mixer heating
circuit1/ MC2= mixer heating circuit 2
æçèéêëìí
æçèéêëìí
æçèéêëìí
æçèéêëìí
When pressed the boiler operates at its maximum preset
temperature for 20 minutes. After this time the emission
measurement can be started again.
For more information see Operating Instructions -
Special operating modes -Emission measure-
ment
For more information see Operating Instructions -
Temperature settings
Operational elements (standard unit)
1 Main knob with two functions (turn, push)
2 Setting daytime temperature
3 Setting set back temperature
4 Setting hot-water temperature
5 Heating and set back operational modes
6 Setting heating characteristics
7 Displaying operation information and temperatures
8 Manual mode and emission measurement
9 Backlit LCD display
10 – Operating instructions summary slot
Art. 0450017005 - 0525-21
Subject to change
see standard unit, additionally under hinged cover:
11 – Safety temperature limiter (STB)
12 – Mains fuse
13 – Mains switch
Operational elements (boiler control panel)
72.5
20: 00
EMISSION
°C
min
Emission measurement (for flue cleansing)
remainig time since set
current boiler
temperature
early termination of emission measurement
10
13
11
12
2
3
4
5
6
7
1
8
9
10
6699..55
1166::3322
MMOO.. 2222..AAUUGG..""0055
°C
0
246
10
12
18 2220
81416
24
The following operational modes can be selected:
1. Short period operational modes:
æ
HOLIDAY Heating and hot-water operation swit-
ched-off frost protected for holiday peri-
od.
ç
ABSENT
Heating operation is interrupted until set
time of return.
è
PARTY
Heating operation is continued until end
of party.
2. Automatic operational modes:
éé
AUTOMATIC Heating and hot-water operation automati-
cally according to selected timer program.
êê
SUMMER Only hot-water operation according to selec-
ted timer program and hot-water temperature
3. Permanent operational modes:
ë
HEATING Heating and hot-water operation continu-
ously to the set temperatures
ì
RED.HEATING Heating and hot-water operation continu-
ously to the set reduced temperatures
í
STANDBY Complete heating plant frost protected.
switched-off
-
Selection of operational modes:
Pressing the button
¢¢
, the previously selected mode
appears flashing. The other operational modes can be selec-
ted and activated with the knob, simultanously an arrow at the
lower edge of the display points to the appertaining program
symbol.
Example: Select and activate AUTOMATIC- operational mode
Note: For separ
ate selection of operational mode first select
corresponding heating circuit!
At selected short period operational modes the corresponding
time settings such as date of return (HOLIDAY) or time of
Description in detail see Operating Instructions - sections
Operational mode selection for heating and hot-water
Functions of operational modes
Quick operational mode selection
Operational modes (æçèéêëìí)
activate
return (ABSENT) or extended heating operation (PARTY) can be
adjusted).
Example: Set and activate holiday mode
next
TIMEPROGRAMS
HC
TIMEPROGRAMS
20.0
MO-1
06.00-08.00
P2
PjOGjAM
1. Select heating or hot-water circuit
Setting range: Direct circuit (HC), mixer heating circuit 1 (MC1)*,
mixer heating circuit 2 (MC2)*, domestic hot-water circuit (DHW)
2. Select operating times program
Appears only after clearance (see level selection SYSTEM/Parameter PROGRAM = P1-P3)
Setting range: P1, P2, P3
3. Select weekday and heating cycle
Setting order: Mon 1. cycle - Mon 2. cycle, Tue 1. cycle - Tue 2. cycle.. etc. ..Sun 2. cycle
Note: A third cycle is available if the second cycle is programmed.
4. Heating start (
= 1. switching-on time)
Setting range: 0.00 to 24.00 h
Note: The switching-on time is shown additionally by a flashing segment on the upper time bar.
HC
Ã
0
246
10
12
18 2220
81416
24
20.0
MO-1
06.00 -08.00
0
246
10
12
18 2220
81416
24
Ã
next
next
Entry into level selection: Press knob for approx. 3 seconds
3 sec
Entry into the operating times
20.0
MO-1
06.00-08.00
7. Select next weekday and/or heating cycle
if necessary, select and program next heating cycle or weekday as described under 3.
Ã
0
246
10
12
18 2220
81416
24
5. Heating end ( = 1. switching-off time)
Setting range: 0.00 to 24.00 h
Note: The switching-off time is shown additionally by a flashing segment on the upper time bar.
20.0
MO-1
06.00-08.00
Ã
0
246
10
12
18 2220
81416
24
6. Cycle temperature ( = temperature during heating resp. hot-water operati-
on)
Setting range for heating circuits (HC, MC1, MC2): 5.0 °C to 30 °C
for hot-water circuit (DHW): 10.0 °C to maximum DHW-delimitation
Attention: When changing daytime temperature (button
¥¥
) or hot-water temperature
(button
§§
) all related cycle temperatures will be changed by the same amount.
20.0
MO-1
06.00-08.00
Ã
0
246
10
12
18 2220
81416
24
°C
next
next
next
next
Select operating times
set
Automatic
Current operational mode
* not in all units available
27.08
HOLIDAY TIL
27.08
HOLIDAY TIL
. . .
select
Holiday
accept
set
date of return
activate
Current operational mode
°C
°C
°C
°C
æçèéêëìí
æçèéêëìí
. . .
Plant information
The information button displays general information such as tem-
peratures and plant conditions.
Turn knob clockwise:
– Temperatures (real and nominal values)
– variable inputs (function and values)
– meter reading such as consumption datas etc.
Turn knob anti-clockwise:
heating circuit information such as
– Operational mode (Holiday, Absent, Party, Automatic, etc.)
Operating times program (P1 or P1-P3 after clearance)
– mode of operation (daytime or reduced mode, ECO-mode)
– Heating circuit identification (HC, MC1, MC2, DHW)
– Status of heating circuit pumps (ON-OFF)
– Status of mixer position (OPEN-STOP-CLOSE)
– Status of boiler (ON-OFF)
– Status and function of variable outputs
Note: The plant information appear only if available at the type
of instrument.
Description in detail see Operating Instructions - section
Plant information
Programming operating times
Operating times will be programmed as shown below. More informationl see Operating Instructions -
Programming of operating times.
Each setting flashing on the display can be adjusted with the knob and confirmed by pressing it. Re-entry into the previous
selection is done via the info button
¤¤
, re-entry into the standard display via the button
¢¢
or automatically after
approx. 60 seconds.
AUTOMATIC
æçèéêëìí
  • Page 1 1
  • Page 2 2

ACV Control Unit THETA Istruzioni per l'uso

Tipo
Istruzioni per l'uso