FOS D1800 Manuale utente

D

The lightning flash with arrowhead symbol within an equilateral triangle is

intended to alert the user to the presence of uninsulated “dangerous” voltage

within the product's enclosure that may be of sufficient magnitude to constitute

a risk of electric shock to humans.

The exclamation point within an equilateral triangle is intended to alert the user

tothe presence of important operating and maintenance (servicing) instructions

in this manual.

The lightning flashes printed next to the output terminals of the amplifier are

intended to alert the user to the risk of hazardous energy. Output connectors

that could pose a risk are marked with the lightning flash. Do not touch output

terminals while amplifier power is on. Make all connections with amplifier

turned off.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE

COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALI-

FIED PERSON NEL.

WARNING: To prevent fire or electric shock, do not expose this equipment to

rain or moisture.

This amplifier has a serial number located on the rear panel.

Please write this and the model number down and keep them for your records.

Keep your purchase receipt. It is your proof of purchase.

Serial Number:

Date of Purchase:

Purchased From:

Important Safety Precautions & Explanation of Symbols

1

The lightning flash with arrowhead symbol within an equilateral triangle is

intended to alert the user to the presence of uninsulated “dangerous” voltage

within the product's enclosure that may be of sufficient magnitude to constitute

a risk of electric shock to humans.

The exclamation point within an equilateral triangle is intended to alert the user

tothe presence of important operating and maintenance (servicing) instructions

in this manual.

The lightning flashes printed next to the output terminals of the amplifier are

intended to alert the user to the risk of hazardous energy. Output connectors

that could pose a risk are marked with the lightning flash. Do not touch output

terminals while amplifier power is on. Make all connections with amplifier

turned off.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE

COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALI-

FIED PERSON NEL.

WARNING: To prevent fire or electric shock, do not expose this equipment to

rain or moisture.

Do not put any containers that hold water on the amplifier,

just in case the water would drip into the amplifier and cause electric shock.

This amplifier has a serial number located on the rear panel.

Please write this and the model number down and keep them for your records.

Keep your purchase receipt. It is your proof of purchase.

Serial Number:

Date of Purchase:

Purchased From:

INTRODUCTION

CONTROLS, CONNECTORS & FEATURES

1- Gain Controll

2-Signal Display

3-Clip Display

4- Mute(protetion) Display

5-Power Display

6-Power Switch

7-Power cord connector

8-Serial number label

9-Output power reference

10-Speakon output connectors

11-XLR input connectors

12-Output voltage selecting

13-Input Sensitivity Selecting

14-Signal Connect Selecting

15-XLR link connectors

1 2 3 45 6

7 8 10 9 11

1213

14

15

7 8 9 10 11 1213 14

Please read the following directions and obtain the best results.

Key features:

- 4 channels

- XLR input connectors

- Speakon output connectors

- Each channel has independent Clip Limiter

ereo and - St Parallel modes of operations

- Reliability

- Complete amplifier protection

12

3

Gnd

12

3

XLR INPUTS

1. Balanced input connections

XLR input connectors are electronically balanced;

XLR input connectors should be wired as follow:

Pin 1 Groud/ shield

Pin 2 positive (+)

Pin 3 negative (-)

2.Unbalanced input connections

To connect an input to an unbalanced source, it is possible to connect Pin1 and Pin3 in the XLR

plug at the amplifier end of the cable. However, a better method is to connect Pin3 to the shield at

the sourse end of the cable, as this usually results in better hum and noise rejection. Balanced input

connetions are recommended whenever possible.

SPEAKON OUPTPUTS

Each channel accepts a normal 2-wire cable. Stereo and parallel mode-

connect every speaker to the amplifier channel, and select stereo

or parallel mode as follow

Each channel is with a balanced XLR input connector. It's connected in a

standard way and can be changed quickly and easily. Balanced connect is

recommended so as to reduce the AC noise and interrupt, especially when

using long cable. Unbalanced connect should be used with short cable, and

the signal resistance should be no more than 600 ohms.

OUTPUT TERMINAL SAFETY WARNING!

Do not touch output terminals while amplifier power is on.

Turn off the amplifier before connecting, or else there will be risk

of hazardous energy!

Output Voltage Peak Limiter(VPL)

Voltage Peak Limiter (VPL) is a unique feature in D series amplifiers. It is used to select the maximum

power available on each output channel. The VPL allows you to set the correct output power for the

connected speakers to get to its best performance. The correct configuration is depended on the

system type and the load of connected channel.

If you choose a lower VPL setting, you only reduce the output voltage. At the same time, this allows

more current headroom for low-impedance loads. The amplifier thus runs at higher efficiency, with

a significantly reduced risk of going into thermal protection.

There's no bridge mode on this amplifier.

Do not support hot-plugging. Only plug in or out input signal when the power is off.

.

+

2 +

2 -

1 -

-1 +

SELECTING STEREO OR PARALLEL MODE

The amplifier can be set for normal Stereo operation or Parallel input Mode.

Stereo Mode - Each channel remains independent. The amplifier may be used

for two different signals.

Parallel Mode - This setting connects two input signal ( for 2-channel amplifier)

or four input signal ( for 4-channel amplifier)l together. One signal feeds both channels

(2-channel amplifier) or 4 channels(4-channel amplifier). Controlling by the input connector

and gain of channel A.

For 3 channel amplifier, it's without sucn function.

Do not connect different inputs to any side that opposites the channel

when operating in Parallel Mode.

GAIN CONTROLS

Turn the Gain controls clockwise to increase Gain and

counterclockwise to decrease Gain.

LED INDICATORS

Displays

The LED displays for each channel operate as follows:

Typical Power Up and Power Down Operation

When the amplifier is first turned on, the green POWER displays will light up , and there will

be a 2-second turn-on delay, during which all red LEDs will be bright (MUTE LED). The signal

LEDs are green.

CLIP LEDs not fully bright - maybe the output is overloaded or clip limiter is working

CLIP flashing and other LEDs are all on - the amplifier is reaching its full output, the clip circuit

is working to prevent overload output.

MUTE flashing - hot reducing and fans speed up.

Overheat Situation:

When the ventilation is not good or the amplifier is overloaded under low impedance, it will

lead to the overheat protection.

The overheat protections is as follow:

25-50 : fans run in low speed ℃

50-60 : fans run from low speed to high ℃

75 : protection LEDs start to flash℃

85 : protection splash quickly and CLIP LED is illuminated, output is controlled at 15 dB℃

90 : overheat protection, the protection LEDs flash in high speed and the CLIP LED is fully ℃

bright, which shows the extreme low load, no ventilation or fans are broken.

POWER Green Main power supply active on this channel.

Clip LED on Shows activity of Limiting circuit,

which responds to both clipping and to thermal

overload.Protect Red Flashes as amplifier

approaches maximum temperature.

CLIP Yellow

SPECIFICATIONS

D1200 D1800 D2600 D3000 D3600

8 Stereo Power 2X600W 2X900W 2X1250W 2X1500W 2X1800W ohms

4 Stereo Power 2X1200W 2X1800W 2X2500W 2X3000W 2X3600W ohms

Input connetor XLR female

Input impedance 20k ohms balanced

Input Sensitivity 0.77V 1.44V

Input CMRR >80dB

Output connector Speakon

Hum&Noise >112dB

Damping Factor >1000 @ 8 ohms

THD <0.1% (20Hz-20kHz 1W)

Frequency Response 20Hz-34KHz,(+0/-0.3dB, 1W/8ohms)

Level control front level meter, from negative infinity to 0dB

Cooling variable speed fans, front to rear airflow

Power Requirement AC voltage 180-240V 50-60Hz

A 88mmX488mmX438mplifier dimensions mm

acking dimensions 1 0mmX mm 5 0mmP 5 600 X 5

et weight(kg) 1N 0.5 11.5 11.5 11.5 12

ross weight(kg) 1G 3.6 14.6 14.6 14.6 15.1

D4004 D6004

8 Stereo Power 4X900W 4X1500W ohms

4 Stereo Power 4X1800W 4X3000W ohms

Input connetor XLR female

Input impedance 20k ohms balanced

Input Sensitivity 0.77V 1.44V

Input CMRR >80dB

Output connector Speakon

Hum&Noise >112dB

Damping Factor >1000 @ 8 ohms

THD <0.1% (20Hz-20kHz 1W)

Frequency Response 20Hz-34KHz,(+0/-0.3dB, 1W/8ohms)

Level control front level meter, from negative infinity to 0dB

Cooling variable speed fans, front to rear airflow

Power Requirement AC voltage 180-240V 50-60Hz

A 88mmX490mmX4mplifier dimensions 15mm

acking dimensions 1 0mmX mm 5 0mmP 5 600 X 2

et weight(kg) 1N 2.7 13

ross weight(kg) 1G 5.9 16.2

FOS D1800 Manuale utente

Questo manuale è adatto anche per

FOS D1800 Manuale utente

in altre lingue

Documenti correlati

Altri documenti