Denver CRL-310 Manuale utente

I N S T R U C T I O N M A N U A L

B R U K S A N V I S N I N G

BETJENINGSVEJLEDNING

B E D IE N UN G SA N LE I TU N G

M O D E D ’ E M P L O I

MANUAL DE INSTRUÇÕES

INSTRUCCIONES DE U SO

K Ä Y T T Ö O H J E E T

GEBRUIKERSHANDLEIDING

I N S T R U K C J A O B S Ł U G I

MANUALE D’ISTRUZIONI

www.denver-electronics.com

www.facebook.com/denverelectronics

CRL-310

ENGLISH

FUNCTION AND CONTROLS

1. LAMP SHADE

2. DISPLAY

3. LIGHT ON-OFF

4. TO SET THE LIGHT INTENSITY LOW

5. TO SET THE LIGHT INTENSITY HIGH

6. MOOD LIGHT ON –OFF / MOOD LIGHT SELECT

7. TIME SET / TEMPERATURE / MEMORY / MEMORY+

8. SNOOZE / SLEEP / DIMMER

9. SOURCE/ DISPLAY OFF

10. << / TUNE - / YEAR/MONTH-DAY / C-F / BETWEEN DISPLAY

CONTENTS ON-OFF / NATURAL SOUND SELECT <<

11. >> / TUNE + / NAP / DST / NATURAL SOUND SELECT >>

12. ALARM 1 CONTROL / VOLUME DOWN

13. ALARM 2 CONTROL / VOLUME UP

14. ON / OFF / ALARM OFF

15. AUX IN JACK

16. DC POWER INPUT

17. TEMPERATURE SENSOR (IN DOOR)

18. SPEAKER

19. RATING LABEL (BOTTOM OF UNIT)

20. FM ANTENNA

21. BATTERY COMPARTMENT (BOTTOM OF UNIT)

ENG-1

LOCATION OF REMOTE CONTROLS

1. ON/OFF / ALARM OFF

2. SOURCE / DISPLAY OFF

3. SNOOZE / SLEEP / DIMMER

4. LIGHT ON/OFF

5. MOOD LIGHT ON / OFF

6. TEMPERATURE / C-F

7. << / TUNE - / BETWEEN DISPLAY CONTENTS ON-OFF

8. ALARM 1 CONTROL

9. VOLUME DOWN

10. ALARM 2 CONTROL

11. >> / TUNE + / NAP / DST

12. TIME SET / MEMORY / MEMORY+

13. YEAR/MONTH-DAY

14. VOLUME UP

15. NATURAL SOUND SELECT

16. MOOD LIGHT SELECT (To turn the unit RGB color changing or

to stop the MOOD LIGHT color changing.)

17. TO SET THE LIGHT INTENSITY HIGH

18. TO SET THE LIGHT INTENSITY LOW

ENG-2

LED DISPLAY MODE

Get started

• Select a proper place for the device such as a dry, and even non

slip area where you can easily operate the device.

• Inserting the Battery (Backup)

INSTALLING/REPLACING THE BACK-UP BATTERY

This unit is equipped with a battery back-up system, requiring one

DC3V CR2032 lithium battery (not included) to maintain the time/

calendar settings and radio presets during AC power outage.

1. Unscrew and remove the BATTERY COMPARTMENT COVER.

2. Install one fresh CR2032 lithium battery into the battery

compartment following the polarity diagram on the BATTERY

COMPARTMENT COVER. Use only the specied size and type

of battery.

3. Replace the BATTERY COMPARTMENT COVER and tighten its

screw.

AC POWER CONNECTION

Plug the AC Power Adaptor into a household outlet AC source.

SETTING THE CALENDAR AND TIME

1. In standby mode, press and hold the unit button (7) or the

remote control button (12) for about 2 seconds to enter the

calendar/time set mode.

2. The year indicator will ash on the LED DISPLAY for up to 30

seconds prompting for a new entry.

3. While the display is ashing, repeatedly tap the unit buttons

(10), (11) or the remote control button (7), (11) to adjust to the

correct year. Press and hold the unit (10), (11) button or the

ENG-3

PM Indicator

AUX Indicator

ALARM 1 Indicator

FM Indicator

ALARM 2 Indicator

TIME Indicator

TEMPERATURE Indicator

MONTH Indicator

DAY Indicator

remote control button (7), (11) for faster scanning backward or

forward. Tap the unit button (7) or the remote control button (12)

to conrm.

4. Repeat steps #2 to #3 to adjust the month, day, time format,

current hour and nally current minute in the same way.

Notes:

- The display sequence in calendar / time set mode will be as

follows:

Year → Month → Date → 12/24 Hour Time Format → Real Time

Hour → Real Time Min → Normal Time

- To check the year while current time is displayed, tap the

unit button (10) or the remote control button (13) once. The LED

DISPLAY will change to year display for 5 seconds and then

revert to current time automatically.

- To check the date while current time is displayed, tap the

unit button (10) or the remote control button (13) twice. The LED

DISPLAY will change to date display for 5 seconds and then

revert to current time automatically.

- During the time set, if no button is being pressed within 10

seconds, the current display time will be automatically stored.

- Make sure the hour is set so that the PM indicator is displayed

correctly for afternoon/night times.

Switching the Unit On/Off

Press the unit on/off button (14) or the remote control on/off button

(1) to switch the unit on or off.

Volume Adjust

Press the unit (12) and (13) button or the remote control button (9)

and (14) button to set the desired volume level. The volume level

reading will appear in the LED DISPLAY.

Display Brightness (in standby)

In standby mode, Press the unit DIMMER button (8) or the remote

control DIMMER button (3) to adjust the display brightness.

ENG-4

Display on/off function

• In standby mode, press and hold unit SOURCE button (9) or the

remote control SOURCE button (2) for 3 seconds. “ON” appears

on the display (2).

• After 15 seconds, the display (2) turns off.

• Press any button to turn the display (2) on for another 15

seconds.

• To deactivate the display on/off function, press and hold unit

SOURCE button (9) or the remote control SOURCE button (2)

for 3 seconds. “OFF” appears on the display (2).

Reading light function

1. Press the unit button (3) or the remote control button (4) to turn

on the function.

2. Use the unit button (5) or the remote control button (17) to

increase the brightness. Use the unit button (4) or the remote

control button (18) to reduce the brightness.

3. In order to turn off the function, press the button again.

Mood light

1. Press the unit button (6) or the remote control button (5) to turn

on the mood light. The light will alternate in different colors.

2. Press and hold the unit button (6) for about 3 seconds or Press

the remote control button (16) to stop or start the mood light

color changing.

3. In order to turn off the mood light, press the unit button (6) or the

remote control button (5) again.

Toggle temperature display between °C (Celsius) and °F

(Fahrenheit)

1. Press the device to standby mode using the unit button (14) or

the remote control button (1).

2. Press the unit button (7) or the remote control button (6) to

display the temperature.

3. While the temperature is displayed, press the unit button (10) or

the remote control button (6) for about 3 seconds to switch

between °C and °F.

RADIO TUNING

1. In standby mode, Press the unit on/off button (14) or the remote

control on/off button (1) to turn the unit ‘On’.

ENG-5

2. The LED DISPLAY will show the radio frequency for about 5

seconds and then revert to normal time display.

AUTOMATIC SEARCH FOR RADIO STATIONS

To automatically search for stations with strong signals, press and

hold the main unit button (10) and (11) or the remote control button

(7) and (11) until the frequency readout on the display begins to

scan. Release the button. The tuner will stop on the rst strong

station it nds.

MANUAL SEARCH FOR RADIO STATIONS

1. Tap the unit (10) and (11) button or the remote control button (7)

and (11) repeatedly to choose your desired radio station.

2. Tap the unit (12) and (13) button or the remote control button (9)

and (14) to set the desired volume level. The volume level

reading will appear in the LED DISPLAY.

Notes:

- Use manual tuning to select weaker stations that might be

skipped during automatic tuning.

- If the automatic tuning does not stop on the exact frequency of

the station, for example, it stops on 88.9 MHz instead of 88.8

MHz, use the manual tuning method to “ne tune” to the exact

frequency of the desired station.

HINTS FOR BEST RECEPTION

FM - To insure maximum FM tuner reception, unwrap and fully

extend the EXTERNAL FM WIRE ANTENNA for best FM radio

reception.

TO SET/RECALL RADIO STATION PRESETS

1. Press the unit button (10) and (11) or the remote control button

(7) and (11) select the desired radio station.

2. Press and hold the unit (7) button or the remote control button

(12), the next available preset memory number will ash on

the LED display. (Note: “P01” will ash in the display if you are

programming presets for the rst time.)

3. Press the unit button (10) and (11) or the remote control button

(7) and (11) to change to the desired preset number P01 thru

P10.

4. Repeat steps 1 thru 3 to preset up to10 FM stations.

5. To recall one of the preset stations already programmed, Press

ENG-6

the unit button (7) or the remote control button (12) repeatedly

until you reach the desired preset number/radio station.

ALARM SETTING

You can set two alarm times. 6 different alarm options are available:

Radio + Light / Radio / Buzzer + Light / Buzzer / Natural sound +

Light / Natural sound.

The setting sequence for AL1 and AL2 is as follows:

In radio off mode, Press the main unit alarm set buttons (12) and (13)

or the remote control buttons (8) and (10) to show the alarm time.

Afterwards keep depress the unit alarm set button (12) and (13) or

the remote control button (8) and (10) over 2 seconds to enter the

alarm set mode. After enter the setting mode, press the unit alarm

set button (12) and (13) to change the mode cycle as follows:

SETTING THE ALARM 1 (BEEPER)

Normal Time→ AL 1 Hour → AL 1 Min → AL 1 weekday Alarm →

AL 1 beeper →Light → Light intensity → Normal Time.

SETTING THE ALARM 1 (RADIO)

Normal Time → AL 1 Hour → AL 1 Minute → AL 1 weekday → AL 1

beeper → AL 1 radio → AL 1 nal radio volume →AL 1 Light → AL 1

Light intensity → Normal Time.

SETTING THE ALARM 1 (NATURAL SOUND)

Normal Time → AL 1 Hour → AL 1 Minute → AL 1 weekday → AL 1

beeper → AL 1 radio →AL 1 natural sound →(Use the unit buttons

(10) and (11) or the remote control buttons (7) and (11) to select the

desired natural sound) →AL 1 nal natural sound volume →AL 1

Light → AL 1 Light intensity → Normal Time

SETTING THE ALARM 2 (BEEPER)

Normal Time→ AL 2 Hour → AL 2 Min → AL 2 weekday Alarm →

AL 2 beeper →Light → Light intensity → Normal Time.

SETTING THE ALARM 2 (RADIO)

Normal Time → AL 2 Hour → AL 2 Minute → AL 2 weekday → AL 2

beeper → AL 2 radio → AL 2 nal radio volume →AL 2 Light → AL 2

Light intensity → Normal Time.

ENG-7

SETTING THE ALARM 2 (NATURAL SOUND)

Normal Time → AL 2 Hour → AL 2 Minute → AL 2 weekday → AL 2

beeper → AL 2 radio →AL 2 natural sound →(Use the unit buttons

(10) and (11) or the remote control buttons (7) and (11) to select the

desired natural sound) →AL 2 nal natural sound volume →AL 2

Light → AL 2 Light intensity → Normal Time.

Proceed as follows:

1. In standby mode, Press the unit Alarm1 button (12) or the

remote control button (8). The currently set alarm time is shown.

2. Keep the button pressed for approx. 3 seconds when the alarm

time is displayed. The hours of the currently set alarm time start

to ash.

3. Use the unit buttons (10) and (11) or the remote control button

(7) and (11) for setting.

4. Press the unit Alarm 1 button (12) or the remote control button

(8) for conrmation. The minutes start to ash.

5. Use the unit buttons (10) and (11) or the remote control button

(7) and (11) for setting.

6. Now select the days you want the alarm to sound. The following

selections can be made:

• 1-5 = Monday to Friday

• 1-7 = Monday to Sunday

• 6-7 = Saturday and Sunday

• 1-1 = Weekday

6a. When you have selected the setting 1-1:

1. Press the button to select the weekday.

2. Make your selection with the buttons and.

(1 = Monday, 2 = Tuesday, 3 = Wednesday, 4 = Thursday, 5 = Friday,

6 = Saturday, 7 = Sunday)

7. Press the button to conrm. Then select how you want to be

awakened. Select from:

• “bu” (buzzer):

A buzzer sounds when the alarm time is reached.

The buzzer interval increases from slow to fast. The volume cannot

be adjusted.

• Radio frequency is displayed:

As soon as your set alarm time is shown, the radio switches on. The

last set station is played. The volume increases slowly to the set

volume. The volume cannot be adjusted.

ENG-8

• NS (natural sound):

As soon as your set alarm time is shown, the natural sound switches

on. The natural sound is played. The volume increases slowly to the

set volume. The volume cannot be adjusted.

NOTE:

• The alarm function turns off automatically after 30 minutes until

the next day.

7a. If you want to be awakened by a radio station, select the

maximum alarm volume using the unit (10) and (11) buttons or

the remote control (7) and (11) buttons.

8. Press the unit Alarm 1 button (12) or the remote control Alarm 1

button (8) to conrm. Then select the light intensity (L) for the

alarm function. Selecting “OFF” will cancel this function.

NOTE:

The light inside the lamp shade (1) will turn on 30 minutes prior

to the pre-set alarm time. The brightness will gradually increase,

starting at the intensity level previously set.

9. Finally, press the button again. The rst alarm time is now

activated.

To set the second alarm time, repeat the above steps with the

main unit Alarm 2 button (13) or the remote control Alarm 2

button (10).

NOTE:

• If the alarm time has been activated, AL1 or AL2 will appear in

the display.

• In order to briey display the set alarm times, press the unit

Alarm 1 button (12) or the remote control Alarm 1 button (8),

respectively the unit Alarm 2 button (13) or the remote control

Alarm 2 button (10).

• Turning off the Alarm Press the unit on/off button (14) or the

remote control on/off button (1) to stop the alarm.

Deactivate the Alarm Function

1. Switch the device to standby with the unit button (14) or the

remote control button (1).

2. To deactivate the alarm function, press and hold the main unit

button (12) and (13) or the remote control button (8) and (10) for

about 3 seconds. AL1 or AL2 will disappear.

ENG-9

SNOOZE FUNCTION (MAIN UNIT)

When the alarm source is sounding, press the unit any buttons

(except on/off button (14)) or the remote control SNOOZE button (3)

to suspend the alarm and activate the snooze function. The Alarm

will temporarily stop and sound again 9 minutes later but the AL1 (or

AL2) indicator will keep ashing.

Notes:

This manual snooze operation can be repeated again and again.

To turn off the snooze function, Press the main unit on/off button

(14) or the remote control on/off button (1). The AL1 (or AL2)

INDICATOR will stop ashing

SLEEP OPERATION

The sleep timer allows you to turn the unit off after a designated

time has elapsed.

1. While listening to the radio, tap the unit button SLEEP button

(8) or the remote control button (3) the sleep time ‘90’ (minutes)

appears in the LED DISPLAY.

2. Repeatedly tap the SLEEP button to select a sleep timer of 90,

60, 30 or 15 minutes. Wait for about 10 seconds after your

selection for the unit to conrm the selection, the unit will play

for the selected length of time then turn itself ‘Off’ automatically.

3. To cancel the sleep timer, repeatedly tap the SLEEP button until

you see the current time in the LED DISPLAY after last sleep

timer option (15 minutes).

• This function can be cancelled with the button (14).

4. This function can be cancelled with the unit button (14) or the

remote control button (1).

Note:

There is no sleep indicator in this unit. To check the remaining sleep

time, tap the SLEEP button once.

Nap alarm

The nap alarm can be used for e.g. a short “nap”. The function only

operates in standby.

• Press the unit button (11) or the remote control button (11) to

select the time after which the device will beep. Select from 90

to 10 minutes or OFF (off) in steps of 10 minutes.

• After the selected time has elapsed, an increasingly fast beep

will sound. Use the unit button (14) or the remote control button

(1) to turn off the beep.

ENG-10

Note: When using the NAP alarm the wake up light function is

inactive.

NATURAL SOUND

1. In standby mode, tap the unit ON-OFF button (14) or the remote

control ON-OFF button (1) to turn the unit ‘On’.

2. Press the unit button (9) or the remote control button (2) to

switch to natural sound mode.

3. Use the main unit buttons (10) and (11) or the remote control

button (15) to select the desired natural sound.

DAYLIGHT SAVING TIME (DST) MODE

If daylight saving time (DST) is available in the summer time in your

State, you may use this option to adjust to the correct time easily.

1. In standby mode, press and hold the unit DST button (11) or the

remote control button (11) for 2 seconds to advance the

displayed time by one hour.

2. To cancel DST mode, repeat the above operation.

AUX IN JACK

(Cable not included)

1. If required, use a suitable adapter (not included). Connect the

external device as follows :

• With a 3.5 mm stereo jack plug to the AUX IN socket (15).

2. Turn the device on using the unit button (14) or the remote

control button (1). Press the unit button (9) or the remote control

button (2) to switch to AUX IN mode. AUX IN appears in the

display.

3. Start the playback of your audio source. Listen to the sound

playback via the speaker. You can adjust the volume using the

unit buttons (11/12) or the remote control button (9/14).

4. For the further procedure, please refer to the user manual of the

external audio source.

NOTE:

If possible, adjust the volume of the external unit to a comfortable

level.

Stop AUX IN operation

Disconnect the cable from the AUX IN jack. Press the unit on/off

button (14) or the remote control button (1) to turn the unit off.

ENG-11

ALTERNATE DISPLAY BETWEEN TIME AND TEMPERATURE

MONTH-DATE DISPLAY

1. In radio off mode, press and hold the unit button (10) or the

remote control button (7) for about 3 seconds until “ON” appears

in the LED DISPLAY.

2. The DISPLAY will alternate between the current Time for 10

seconds and month- date for 5 seconds and temperature for 5

seconds as follows:

To cancel this function, press and hold the unit button (10) or the

remote control button (7) for about 3 seconds until “OFF” appears

on the LED DISPLAY. The DISPLAY will switch back to normal time

display.

NOTE

If you replace the battery, do not disconnect AC plug from AC outlet.

Otherwise, current time and alarm will be initialized.

SPECIFICATIONS

Frequency range: FM 87.5 – 108 MHz

In door Temperature Sensor Range: 32 °F to 122 °F (0°C to +50°C)

Battery backup: 3V (CR2032 Flat Lithium

battery x 1)

Power Adaptor: Input AC 100-240V 50- 60 Hz

- Output DC 5V 1200mA

ENG-12

TIME Indicator

Display for 10 second Display for 5 second Display for 5 second

TEMPERATURE IndicatorMONTH Indicator

DAY Indicator

WARNING

1. No naked ame sources, such as lighted candles, should be

placed on the apparatus.

2. Do not place the product in closed bookcases or racks without

proper ventilation.

3. The mains plug is used as the disconnect device, the disconnect

device shall remain readily operable.

4. The ventilation should not be impeded by covering the

ventilation openings with items, such as newspapers, table-

cloths, curtains, etc.

5. It shall not be exposed to dripping or splashing and that no

objects lled with liquids, such as vases, shall be placed on the

apparatus.

6. Do not connect FM antenna to outside antenna.

7. The unit should not be exposed to direct sunlight, very high or

low temperature, moisture, vibrations or placed in dusty

environment.

8. Do not use abrasive, benzene, thinner or other solvents to

clean the surface of the unit. To clean, wipe it will mild non-

abrasive detergent solution and clean soft cloth.

9. Never attempt to insert wires, pins or other such objects into the

vents or opening of the unit.

10. Batteries shall not be exposed to excessive heat such as

sunshine, re or the like.

11. Attention should be drawn to the environmental aspects of

battery disposal.

12. Do not dispose this product into usual household garbage at the

end of its lifecycle; hand it over to a collection center for

recycling the electrical and electronic appliances. By recycling,

some of the materials can be reused. You are making an

important contribution to protect our environment. Please inquire

your community administration for the authorized disposal

center.

CAUTION

Danger of explosion if battery is incorrectly replaced

Replace only with the same or equivalent type

ENG-13

DISPOSAL OF YOUR OLD APPLIANCE OR BATTERY:

1. When this crossed-out wheeled bin symbol is attached to a

product, it means the product is covered by the European

Directive.

2. All electrical and electronic products including battery should

be disposed of separately from the municipal waste stream via

designated collection facilities appointed by the government or

the local authorities.

3. The correct disposal of your old appliance will help prevent

potential negative consequences for the environment and

human health.

4. For more detailed information about disposal of your old

appliance, please contact your city ofce, waste disposal

service or the shop where you purchased the product.

ENG-14

Electric and electronic equipment and included batteries contains

materials, components and substances that can be hazardous to

your health and the environment, if the waste material (discarded

electric and electronic equipment and batteries) is not handled

correctly.

Electric and electronic equipment and batteries is marked with the

crossed out trash can symbol, seen below. This symbol signies

that electric and electronic equipment and batteries should not be

disposed of with other household waste, but should be disposed of

separately.

As the end user it is important that you submit your used batteries

to the appropriate and designated facility. In this manner you make

sure that the batteries are recycled in accordance with legislature

and will not harm the environment.

All cities have established collection points, where electric and

electronic equipment and batteries can either be submitted free

of charge at recycling stations and other collection sites, or be

collected from the households. Additional information is available at

the technical department of your city.

Imported by:

DENVER ELECTRONICS A/S

Stavneagervej 22

DK-8250 Egaa

Denmark

www.facebook.com/denverelectronics

www.denver-electrionics.com

ENG-15

SWEDISH

FUNKTION OCH KONTROLLER

1. LAMPSKÄRM

2. DISPLAY

3. LJUS PÅ-AV

4. STÄLLA IN LJUSSTYRKAN TILL LÅG

5. STÄLLA IN LJUSSTYRKAN TILL HÖG

6. STÄMNINGSBELYSNING PÅN –AV / VAL AV

STÄMNINGSBELYSNING

7. INSTÄLLNING AV TID / TEMPERATUR/ MINNE / MINNE+

8. SNOOZE / SÖMN / DIMMER

9. KÄLLA / DISPLAY AV

10. << / STÄLLA IN- / ÅR/MÅNAD-DAG / C-F / MELLAN DISPLAY

INNEHÅLLET PÅ-AV / VAL AV NATURLIGT LJUD <<

11. >> / STÄLLA IN + / TUPPLUR / DST / VAL AV NATURLIGT

LJUD >>

12. ALARM 1 KONTROLL / VOLYM NED

13. ALARM 2 KONTROLL / VOLYM UPP

14. PÅ / AV / LARM AV

15. AUX IN-UTTAG

16. DC-STRÖMINGÅNG

17. TEMPERATURGIVARE (INOMHUS)

18. HÖGTALARE

19. MÄRKETIKETT (ENHETENS UNDERSIDA)

20. FM-ANTENN

21. BATTERIFACK (ENHETENS UNDERDEL)

SWE-1

PLATS FÖR FJÄRRKONTROLLER

1. PÅ / AV / ALARM AV

2. KÄLLA / DISPLAY AV

3. SNOOZE / SÖMN / DIMMER

4. LAMPA PÅ / AV

5. STÄMNINGSBELYSNING PÅ / AV

6. TEMPERATUR / C-F

7. << / STÄLLA IN - / MELLAN DISPLAY INNEHÅLL PÅ-AV

8. ALARM 1 KONTROLL

9. VOLYM NED

10. ALARM 2 KONTROLL

11. >> / STÄLLA IN + / TUPPLUR / DST

12. INSTÄLLNING AV TID / MINNE / MINNE+

13. ÅR / MÅNAD-DAG

14. VOLYM UPP

15. VAL AV NATURLIGT LJUD

16. VÄLJ STÄMNINGSBELYSNING SELECT (För att växla enheten

RGB färg eller stoppa STÄMNINGSBELYSNING från att

ändras.)

17. STÄLLA IN LJUSSTYRKAN TILL HÖG

18. STÄLLA IN LJUSSTYRKAN TILL LÅG

SWE-2

LED-DISPLAYLÄGE

Komma igång

• Välj en lämplig plats för enheten såsom ett torrt, jämnt och

halkfritt område där du kan lätt använda enheten.

• Sätta i batteriet (Backup)

INSTALLATERA / BYTE AV RESERVBATTERIET

Denna enhet är utrustad med ett reservsystem för batteriet som

kräver ett DC3V CR2032 litiumbatteri (medföljer inte) för att behålla

inställningar för tid / kalender och förinställningar för radio vid

strömavbrott.

1. Skruva loss och ta bort BATTERILUCKAN.

2. Installera ett nytt CR2032 litiumbatteri i batterifacket som

följer diagramet för polaritet på BATTERILUCKAN. Använd

endast angiven storlek och typ av batteri.

3. Sätt tillbaka BATTERILUCKAN och dra åt skruven.

NÄTANSLUTNING

Anslut nätadaptern in i ett vanligt eluttag.

STÄLLA IN KALENDER OCH TID

1. I standby-läge, tryck och håll nere knappen (7) på enheten

eller fjärrkontrollknappen (12) i ca 2 sekunder för att ange läge

för inställning av kalender / tid.

2. Årsindikatorn blinkar på LED-DISPLAYEN i upp till 30 sekunder

som uppmanar om en ny post.

3. Medan displayen blinkar, knacka upprepade gånger på

knapparna (10), (11) på enheten eller fjärrkontrollknapparna

(7), (11) för att ställa in korrekt år. Tryck och håll knapparna (10),

SWE-3

PM indikator

AUX IN indikator

ALARM 1 indikator

FM indikator

ALARM 2 indikator

TIME-indikator

TEMPERATURE indikator

MONTH indikator

DAY indikator

(11) på enheten eller fjärrkontrollknapparna (7), (11) för snabbare

scanning bakåt eller framåt. Tryck på knappen (7) på enheten

eller fjärrkontrollknappen (12) för att bekräfta.

4. Upprepa steg #2 till #3 för att ställa in månad, dag, tidsformat,

aktuell timme och slutligen aktuell minut på samma sätt.

Obs!

- Visningssekvensen i kalendern / inställda läget för tid kommer

att vara enligt följande:

År → Månad → Datum → 12/24 timmars tidsformat → Verklig timme

→ Verklig min → Normal tid

- För att kontrollera året medan aktuell tid visas, knacka på

knappen (10) på enheten eller fjärrkontrollknappen (13) en gång.

LED-DISPLAY kommer att visa år i 5 sekunder, för att sedan

återgå till aktuell tid automatiskt.

- För att kontrollera datum när aktuell tid visas, tryck på knappen

(10) på enheten eller fjärrkontrollknappen (13) två gånger.

LED-DISPLAYEN kommer att visa datum i 5 sekunder, för att

sedan återgå till aktuell tid automatiskt.

- Vid inställning av tiden, kommer den aktuella visningstiden att

sparas automatiskt, om ingen knapp trycks in inom 10 sekunder.

- Se till att timme är inställd så gjorde PM-indikatorn visas korrekt

för eftermiddag / nattetid.

Slå på och av enheten

Tryck på / av-knappen för enheten (14) eller fjärrkontrollens på / av-

knapp (1) för att slå på / av enheten.

Volyminställning

Tryck på knapparna (12) och (13) på enheten eller

fjärrkontrollknapparna (9) och (14) för att ställa in önskad volymnivå.

Avläsning av volymen visas i LED-DISPLAY.

Displayens ljusstyrka (i standby)

I standby-läge, tryck på DIMMER-knappen (8) på enheten eller

fjärrkontrollknappen för DIMMER (3) för att justera displayens

ljusstyrka.

SWE-4

La pagina sta caricando ...

Denver CRL-310 Manuale utente

Denver CRL-310 Manuale utente

in altre lingue

Documenti correlati

Altri documenti