Datalogic CATCHER D531 Series Guida di riferimento

DIAMOND™ D531 Scanners

Quick Reference

Diamond™ D531 Scanners

QUICK REFERENCE

DATALOGIC S.p.A.

Via Candini 2

40012 - Lippo di Calderara di Reno

Bologna - Italy

Diamond™ D531 Scanners

Ed.: 07/2006

Datalogic reserves the right to make modifications and improvements without prior

notification.

Datalogic shall not be liable for technical or editorial errors or omissions contained herein,

nor for incidental or consequential damages resulting from the use of this material.

Product names mentioned herein are for identification purposes only and may be

trademarks and or registered trademarks of their respective companies.

820001591 (Rev. B)

CONTENTS

Updates and Language Availability......................................................................v

Using Diamond™ ................................................................................................ 1

Sleep State.......................................................................................................... 1

Single Line Mode ................................................................................................ 2

Connections ........................................................................................................ 3

Connecting / Disconnecting the Cable................................................................ 5

Interface Selection .............................................................................................. 5

USB Interface Configuration ............................................................................... 6

USB Interface Selection ...................................................................................... 9

USB Keyboard Nationality................................................................................. 10

RS232 Reader Configuration ............................................................................ 11

Wedge Interface Selection ................................................................................ 12

Wedge Keyboard Nationality............................................................................. 15

Default Values................................................................................................... 16

Operating Test .................................................................................................. 18

Technical Features............................................................................................ 19

Reading Diagram .............................................................................................. 20

Scanner Data Entry........................................................................................... 21

Warranty............................................................................................................ 21

iii

Patents .............................................................................................................. 22

Services and Support........................................................................................ 22

Compliance ....................................................................................................... 23

iv

UPDATES AND LANGUAGE AVAILABILITY

UK/US

The latest drivers and documentation updates for this product are available on

Internet.

Log on to : www.datalogic.com

I

Su Internet sono disponibili le versioni aggiornate di driver e documentazione di

questo prodotto. Questo manuale è disponibile anche nella versione italiana.

Collegarsi a : www.datalogic.com

F

Les versions mises à jour de drivers et documentation de ce produit sont

disponibles sur Internet. Ce manuel est aussi disponible en version française.

Cliquez sur : www.datalogic.com

D

Im Internet finden Sie die aktuellsten Versionen der Treiber und Dokumentation

von diesem Produkt. Die deutschsprachige Version dieses Handbuches ist

auch verfügbar.

Adresse : www.datalogic.com

E

En Internet están disponibles las versiones actualizadas de los drivers y

documentación de este producto. También está disponible la versión en

español de este manual.

Dirección Internet : www.datalogic.com

v

vi

DIAMOND™ D531

USING DIAMOND™

The Datalogic Diamond™ D531 is an omni-directional scanner, which

generates a scan pattern of 16 lines, thus ensuring high performance scanning.

Barcodes are read simply on presentation to the scanner window.

The Diamond™ scanner can be used handsfree as well as hand-held, e.g.:

a) Handsfree scanning by

presenting the item to the scanner using a

sweeping curved motion towards the scanner window.

b) You can also use it as a hand-held device by

presenting the scanner to the

item using a sweeping curved motion towards the item.

SLEEP STATE

After a default stand-by timeout the scanner enters a "Sleep" state for minimum

power consumption in which the scanner Laser is OFF and the motor is not

rotating.

It is possible to exit this state by simply pressing the trigger.

1

DATALOGIC

SINGLE LINE MODE

When many barcodes are present in the same reading area, like in barcode

price lists or in the case of configuration barcodes in this manual, selecting a

specific barcode to read is not practical with the large raster pattern emitted by

the Diamond™, so a special single line scanning mode can be easily entered to

perform this task. In this mode only a single scanning line is enabled so that

aiming and reading barcodes become very easy.

To use single line mode for barcode reading follow the procedure below:

1. While the normal raster pattern is present, press the trigger. A single laser

line will appear but barcodes cannot be decoded.

2. Position the presentation scanner over the code to read and press the

trigger

within 5 seconds to decode the code.

When using the scanner for data entry, a programmable timeout is provided to

assure that Diamond™ will return to raster mode if barcode reading is not

successful in single line (Single Line Decoding Duration). Also a programmable

timeout is available to manage how long to wait after successful reading before

returning to raster mode (Single Line Timeout OFF Before Raster).

If you need to make consecutive readings in single line mode, simply repeat the

procedure before the Single Line Timeout OFF Before Raster expires.

When in configuration, Diamond™ will remain in single line until the Exit

Configuration barcode is read.

Single Line and

Wakeup Trigger

Good Read

LED

2

DIAMOND™ D531

CONNECTIONS

NOTE

The scanner and the host system must be switched off before

starting the installation of the scanner. By following this

precaution you prevent any electrical damage.

You are advised to install the scanner in a place with good air

circulation out of direct sunlight.

In order to install the scanner:

1. Locate the optimal scanner position in relation to the counter surface.

2. Pay attention to the product flow, the distance to the counter edge and

convenience for the operator.

RS232

3

DATALOGIC

USB

(if required)

KEYBOARD WEDGE

4

DIAMOND™ D531

CONNECTING / DISCONNECTING THE CABLE

Interface Cable

Connector

INTERFACE SELECTION

Follow the procedure to configure the interface required by your application.

• USB Interface

• RS232 Interface

• Wedge Interface

5

DATALOGIC

USB INTERFACE CONFIGURATION

The USB interface is compatible with:

- Windows 98 (and later)

- Mac OS 8.0 (and later)

- IBM POS for Windows

- 4690 Operating System

Start-Up

As with all USB devices, upon connection, the Host performs several checks by

communicating with the Diamond™. During this phase the green LED on the

Diamond™ reader blinks and normal operations are suspended. Two basic

conditions must be met before Diamond™ is ready to read codes,

the correct

USB driver must be loaded and sufficient power must be supplied to the reader.

For all systems, the correct USB driver for the default USB-KBD interface is

included in the Host Operating System and will either be loaded automatically or

will be suggested by the O.S. and should therefore be selected from the dialog

box (the first time only).

If the Host supplies sufficient power to the reader, the start-up phase ends

correctly, the green LED stops blinking and the reader emits the beep OK

signal.

If the Host does not supply sufficient power to the reader, a dialog box will

appear on the Host and the reader will be blocked (green LED continues

blinking). In this case, disconnect the USB cable

at the Host (green LED stops

blinking), connect and power-up an external supply to the USB cable

then

reconnect the USB cable to the Host and close the dialog box. The reader emits

the beep OK signal. You can now read codes. At this point you can read the

USB interface configuration code according to your application. Load drivers

from the O.S. (if requested). When configuring the USB-COM interface, the

relevant files and drivers must be installed from the USB Device Installation

software, which can be downloaded from the web page

http://www.datalogic.com.

The scanner is ready.

6

DIAMOND™ D531

First Start-Up

Connect Diamond™ to

Host

Does a dialog

box appear

warning that Bus

power is not

sufficient?

Select desired USB

interface code

(USB-KBD is default)

Disconnect scanner

at Host

Connect external

power supply to

cable and power up

Reconnect reader

cable to Host and

close dialog box

NO

YES

Read test codes.

Scanner is READY

Load drivers

(if required)

Load drivers

(

if re

q

uired

)

Green LED blinks

Green LED off - BEEP OK

BEEP OK

Green LED off

Successive start-ups will automatically recognize the previously loaded drivers.

If external power is used, verify that external power is already supplied.

7

DATALOGIC

Successive Start-Ups

NO

YES

Read test codes.

Scanner is READY

Green LED blinks

Green LED off - BEEP OK

BEEP OK

Connect Diamond™ to

Host

Disconnect scanner

at Host

Connect external

power supply to

cable and power up

Reconnect reader

cable to Host and

close dialog box

Does a dialog box

appear warning

that Bus power is

not sufficient?

Green LED off

8

DIAMOND™ D531

USB INTERFACE SELECTION

USB-KBD

Ì$+UA03$-:Î

USB-KBD-ALT-MODE

Ì$+UA04$-@Î

USB-KBD-APPLE

Ì$+UA05$-FÎ

USB-COM*

Ì$+UA02$-4Î

USB-IBM-Table Top

Ì$+UA00$-(Î

USB-IBM-Hand Held

Ì$+UA01$-.Î

* When configuring USB-COM, the relevant files and drivers must be installed

from the USB Device Installation software, which can be downloaded from

the web site

http://www.datalogic.com.

9

DATALOGIC

USB KEYBOARD NATIONALITY

USB-KBD users should select one of the following keyboard nationality codes.

Belge

Ì$+FJ7$-8Î

Deutsch

Ì$+FJ3$-$Î

English

Ì$+FJ4$-)Î

Español

Ì$+FJ6$-3Î

Français

Ì$+FJ2$-ÊÎ

Italiano

Ì$+FJ1$-ÅÎ

Svenskt

Ì$+FJ5$-.Î

USA

Ì$+FJ0$-|Î

Japanese

Ì$+FJ8$-=Î

10

DIAMOND™ D531

RS232 READER CONFIGURATION

Read the restore default code, then read the interface selection code for your

application:

RESTORE DEFAULT

Ì$+$*oÎ

RS232 INTERFACE

Standard

Ì$+CP0$-$Î

POS TERMINALS

Nixdorf Mode A

Ì$+CM2EC0$->Î

Fujitsu

Ì$+CM1$-ÈÎ

ICL Mode

Ì$+CM0$-ÃÎ

11

DATALOGIC

WEDGE INTERFACE SELECTION

Read the restore default code, then read the interface selection code for your

application:

RESTORE DEFAULT

Ì$+$*oÎ

WEDGE INTERFACE

IBM AT or PS/2 PCs

Ì$+CP500$-aÎ

IBM XT

Ì$+CP503$-vÎ

PC Notebook

Ì$+CP505$-ÈÎ

IBM SURE1

Ì$+CP506$-$Î

IBM Terminal 3153

Ì$+CP504$-}Î

12

La pagina sta caricando ...

Datalogic CATCHER D531 Series Guida di riferimento

Questo manuale è adatto anche per

Datalogic CATCHER D531 Series Guida di riferimento

in altre lingue

Documenti correlati

Altri documenti