Sharp R-22AM Manuale utente

Marca: Sharp

Modello: R-22AM

Categoria: Microonde

Tipo: Manuale utente

Questo manuale è adatto anche per

R-25AM

SHARP CORPORATION

SERVICE MANUAL

S0315R25AMH//

COMMERCIAL

MICROWAVE OVEN

MODEL

R-25AM

In interests of user-safety the oven should be restored to its

original condition and only parts identical to those specified

should be used.

TABLE OF CONTENTS

Page

CAUTION, MICROWAVE RADIATION....................................................................... INSIDE FRONT COVER

WARNING ..........................................................................................................................................................1

SERVICING ...................................................................................................................................................... 2

PRODUCT SPECIFICATIONS ......................................................................................................................... 5

GENERAL INFORMATION ................................................................................................................................5

APPEARANCE VIEW ....................................................................................................................................... 6

OPERATION SEQUENCE................................................................................................................................ 7

FUNCTION OF IMPORTANT COMPONENTS ................................................................................................ 9

TROUBLESHOOTING GUIDE ........................................................................................................................10

TEST PROCEDURE ........................................................................................................................................12

TOUCH CONTROL PANEL ASSEMBLY ........................................................................................................ 18

COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE ........................................................... 25

MICROWAVE MEASUREMENT .................................................................................................................... 32

TEST DATA AT A GLANCE ........................................................................................................................... 33

WIRING DIAGRAM ......................................................................................................................................... 34

PICTORIAL DIAGRAM ................................................................................................................................... 36

CONTROL PANEL CIRCUIT ........................................................................................................................... 37

PRINTED WIRING BOARD .............................................................................................................................38

PARTS LIST ................................................................................................................................................... 39

2100W/R-25AM

R-25AM

CAUTION

MICROWAVE RADIATION

Personnel should not be exposed to the microwave energy which may radiate from the

magnetron or other microwave generating devices if it is improperly used or connected.

All input and output microwave connections, waveguides, flanges and gaskets must be

secured.

Never operate the device without a microwave energy absorbing load attached.

Never look into an open waveguide or antenna while the device is energized.

VARNING

MICKROVAGSSTRALING

Personal får inte utsättas för mikrovågsenergi som kan ustrala från magnetronen eller

andre mikrovågsalstrande anordningar om dessa är felanslutna eller används på fel sätt.

Alla in-och utgångsanslutningar för mikrovågor, vagledare, flänsar och packningar måste

vara fast anslutna.

Mikrovågsgeneratorn får inte arbeta utan att absorberande belastning är ansluten. Titta

aldrig in i ën öppen vågledare eller antenn när mikrovågsgeneratorn är påkopplad eller

laddad.

VAROITUS

MIKROAALTOSÄTELYÄ

Käyttäjä ei saa joutua alttiiksi mikroaaltoenergialle, jota voi säteillä magnetronista tai

muusta mikroaaltoja kehittävästä laitteesta, jos sitä käytetään tai jos se kytketään väärin.

Kaikkien mikroaaltoliitäntöjen sekä syöttö-että ulostulopuolella, aaltoputkien laippojen ja

tiivisteiden tulee olla varmistettuja.

Mikroaaltouunnia ei koskaan saa käyttää ilman kuormaa jossa mikroaaltoenergiaa kuluu.

Avoimeen aaltoputkeen tai antenniin ei koskaan saa katsoa virran ollessa kytkettynä.

ADVARSEL

MIKROBØLGESTRÅLING

Personell må ikke utsettes for mikrobølge-energi som kan utståles fra magnetronen eller

andre mikrobølge-generende deler dersom apparatet feilbetjenes eller blir feiltikoplet.

Alle inn-og ut-tilkoplinger i forbindelse med mikrobølge-strålingen, bølgeledere, flenser og

tetningsringer/pakninger må festes ordentlig.

Aldri bruk apparatet med mindre en mikrobålge-absorberende last er plassert i

ovnsrommet.

Aldri se direkte inn i en åpen bølgeleder eller antenne imens apparatet er strømførende.

ADVARSEL

MIKROBØLGEBESTRÄLING

Man bør ikke udsætte sig for mikrobølgebestråling fra magnetronen eller andre

mikrobølgefrembringende anordninger, hvilket kan ske hvis apparatet er forkert tilsluttet

eller bruges forkert. Alle mikrobølgeindgange og-udgange, bølgeledere, flanger og

tætningsstrimler må være forsvarligt udført.

Anvend aldrig ovnen uden en mikrobølgesabsorberende anordning. Se aldrig ind i en

åben bølgeleder eller antenne, mens ovnen er i brug.

R-25AM

SERVICE MANUAL

COMMERCIAL MICROWAVE OVEN

R-25AM

GENERAL IMPORTANT INFORMATION

This Manual has been prepared to provide Sharp Corp. Service

engineers with Operation and Service Information.

It is recommended that service engineers carefully study the entire

text of this manual, so they will be qualified to render satisfactory

customer service.

CAUTION

MICROWAVE RADIATION

DO NOT BECOME EXPOSED TO RADIATION FROM THE

MICROWAVE GENERATOR OR OTHER PARTS THAT CON-

DUCT MICROWAVE ENERGY.

WARNING

Note: The parts marked "*" are used in voltage more

than 250V. (Parts List)

Anm: Delar märket med "*" har en spänning

överstigande 250V.

Huom: Huolto-ohjeeseen merkitty "tähdella" osat joissa

jännite on yli 250 V.

Bemerk: Deler som er merket "asterisk" er utsatt for

spenninger over 250V til jord.

Bemærk: "Dele mærket med stjerne benyttes med højere

spænding end 250 volt.

WARNING

Never operate the oven until the following points are ensured.

(A) The door is tightly closed.

(B) The door brackets and hinges are not defective.

(D) The door is not deformed or warped.

(E) There is not any other visible damage with the oven.

Servicing and repair work must be carried out only by trained service

engineers.

All the parts marked "*" on parts list are used at voltage more than

250V.

Removal of the outer wrap gives access to potential above 250V.

All the parts marked "∆" on the parts list may cause undue

microwave exposure, by themselves, or when they are damaged,

loosened or removed.

SHARP CORPORATION

OSAKA, JAPAN

SERVICING

PRODUCT SPECIFICATIONS

GENERAL INFORMATION

APPEARANCE VIEW

OPERATING SEQUENCE

FUNCTION OF IMPORTANT

COMPONENTS

TROUBLESHOOTING GUIDE

AND TEST PROCEDURE

TOUCH CONTROL PANEL

COMPONENT REPLACEMENT

AND ADJUSTMENT PROCEDURE

MICROWAVE MEASUREMENT

TEST DATA AT A GLANCE

WIRING DIAGRAM

PARTS LIST

R-25AM

REMEMBER TO CHECK 3D

1) Disconnect the supply.

2) Door opened, and wedged open.

3) Discharge two high voltage capacitors.

WARNING: AGAINST THE CHARGE OF THE TWO

HIGH-VOLTAGE CAPACITORS

The two high-voltage capacitors remains charged about 60

seconds after the oven has been switched off. Wait for 60

seconds and then short-circuit the connection of the two

high-voltage capacitors (that is, of the connecting lead of the

high-voltage rectifier) against the chassis with the use of an

insulated screwdriver.

Sharp recommend that wherever possible fault-finding is

carried out with the supply disconnected. It may in, some

cases, be necessary to connect the supply after the outer

case has been removed, in this event carry out 3D checks and

then disconnect the leads to the primary of the two High

voltage transformers. Ensure that these leads remain isolated

from other components and the oven chassis. (Use insulation

tape if necessary.) When the testing is completed carry out 3D

checks and reconnect the leads to the primary of the two High

voltage transformers.

SERVICING

WARNING TO SERVICE PERSONNEL

GB Microwave ovens contain circuitry capable of producing very high voltage and current, contact with following parts will result

in electrocution. High voltage capacitor, High voltage transformer, Magnetron, High voltage rectifier assembly, High voltage

fuses, High voltage harness.

REMEMBER TO CHECK 4R

1) Reconnect all leads removed from components during

testing.

2) Replace the outer case (cabinet).

3) Reconnect the supply.

4) Run the oven. Check all functions.

Microwave ovens should not be run empty. To test for the

presence of microwave energy within a cavity, place a cup of

cold water on the oven turntable, close the door and set the

power to HIGH and set the microwave timer for one (1) minute.

When the one minute has elapsed (timer at zero) carefully

check that the water is now hot. If the water remains cold carry

out

3D checks and re-examine the connections to the compo-

nent being tested.

When all service work is completed, and the oven is fully

assembled, the microwave power output should be checked and

a microwave leakage test should be carried out.

NL Magnetronovens bevatten circuits die een zeer hoge spanning en stroom kunnen voortbrengen. Contact met de

volgende onderdelen kan elektrocutie tot gevolg hebben.

Hoogspanningscondensator, hoogspanningstransformator, magnetron, hoogspanningsgelijkrichter, hoogspannings

kabelboom.

VERGEET DE VOLGENDE 3 STAPPEN NIET

1) Haal de stekker uit het stopcontact.

2) Open de deur en zorg ervoor dat hij niet dicht kan vallen.

3) Ontlaad de hoogspanningscondensator.

PAS OP VOOR DE ELECTRISCHE LADING VAN DE

HOOGSPANNINGSCONDENSATOR

De hoogspanningscondensator blijft nog ongeveer 60

seconden lang opgeladen, nadat de oven is uitgeschakeld.

Wacht 60 seconden voordat u de verbinding van de

hoogspannings-condensator (m.a.w. de verbindingsdraad

van de hoogspanningsgelijkrichter) met een geïsoleerde

schroevedraaier kortsluit tegen het chassis.

Sharp beveelt ten sterkste aan dat, voor zover mogelijk,

defecten worden opgespoord wanneer de stekker uit het

stopcontact is gehaald. Soms is het nodig om de stroomtoevoer

weer tot stand te brengen nadat de buitenmantel verwijderd

is. Herhaal dan de bovengenoemde 3 stappen en haal de

electrische draden uit de primaire zijde van de

vermogenstransformator. Zorg ervoor dat deze draden

geïsoleerd blijven van andere elementen en van het chassis

van de oven. (Gebruik zo nodig isolatieband.) Wanneer de

test is uitgevoerd, herhaalt u de bovenstaande 3 stappen en

verbindt u de electrische draden weer aan de primaire zijde

van de vermogenstransformator.

VERGEET DE VOLGENDE 4 STAPPEN NIET

1) Sluit de draden weer aan diezijn losgehaald voor de test.

2) Plaats de buitenmantel weer om het toestel heen (kabinet).

3) Stop de stekker weer in het stopcontact.

4) Zet de oven aan. Controleer alle functies.

Magnetronovens mogen niet leeg aangezet worden. Om te

controleren of er microgolf-energie binnen de oven wordt

geproduceerd, plaatst u een mok met koud water op de

draaitafel van de oven, sluit de deur, zet de oven op HIGH en

stelt de klok van de magnetron in op twee (2) minuten. Wanneer

de twee minuten voorbij zijn (klok staat op nul), controleert u

voorzichtig of het water heet is. Indien het water nog steeds

koud is, herhaalt u de allereerste drie stappen en controleer

nogmaals de aansluitingen naar de geteste onderdelen.

Wanneer alle reparaties zijn uitgevoerd en de oven weer in

elkaar is gezet, moet de het magnetronvermogen worden

gecontroleerd en moet worden gecontroleerd of er geen

microgolflekkage is.

R-25AM

E Los hornos de microondas contienen circuitos eléctricos capaces de producir voltajes de alta tensión y descargas

eléctricas. Para evitar el riesgo de electrocución, absténgase de tocar los siguientes componentes: condensador de alta

tensión, transformador de alta tensión, magnetrón, dispositivo del rectificador de alta tensión y arnés de alta tensión.

RECUERDE LA COMPROBACION 3D

1) Desconecte la alimentación.

2) Deje la puerta abierta y calzada.

3) Descargue el condensador de alto voltaje.

ADVERTENCIA SOBRE LA CARGA DEL

CONDENSADOR DE ALTO VOLTAJE

El condensador de alto voltaje permanece cargado unos

60 segundos después de haber apagado el horno. Espere

60 segundos y luego ponga en cortocircuito la conexión del

condensador de alto voltaje (esto es, del conductor de

conexión del rectificador de alto voltaje) al chasis con un

destornillador de mango aislado.

Se recomienda encarecidamente que siempre que sea

posible la localización de fallos se realice con la alimentación

desconectada. Puede ser que en algunos casos sea

necesario conectar la alimentación después de haber retirado

la carcasa exterior. En este caso, realice las comprobaciones

3D y luego desconecte los conductores del primario del

transformador de alimentación. Asegúrese de que estos

conductores permanezcan aislados de otros componentes y

del chasis del horno. (Use cinta aislante si es necesario).

Cuando termine la prueba efectúe las comprobaciones 3D y

reconecte los conductores al primario del transformador de

alimentación.

RECUERDE LA COMPROBACION 4C

1) Conecte todos los componentes desconectados de los

componentes durante la prueba.

2) Coloque la carcasa exterior (cabina).

3) Conecte la alimentación.

4) Compruebe todas sus funciones despues de poner en

marcha el horno.

Los hornos de microondas no deben funcionar vacíos. Para

comprobar la presencia de energía de microondas dentro de

una cavidad, coloque una taza de agua fría en el plato giratorio

del horno, cierre la puerta y ponga la potencia en HIGH (alta)

y coloque el temporizador en dos (2) minutos. Cuando

transcurran los dos minutos (temporizador a cero) compruebe

cuidadosamente que el agua se ha calentado. Si el agua

permaneciese fría, efectúe las comprobaciones 3D y vuelva a

examinar las conexiones de los componentes que han sido

probados.

Cuando haya terminado la intervención en el equipo y el horno

haya sido ensamblado de nuevo completamente, deberá

comprobar la potencia de salida de microondas y realizar una

prueba de fugas de microondas.

SV Mikrovågsugnar innehåller kretsar som producerar mycket höga spänningar och strömmar.

Kontakt med följande komponenter kan leda till dödsfall:

Högspänningskondensator, transformator, magnetron, högspännings likriktare, högspännings kablage.

KOM IHÅG ATT KONTROLLERA 3 STEG

1) Koppla från strömkällan.

2) Öppna dörren på glänt.

3) Ladda ur högspänningskondensatorn.

VARNING FÖR LADDNINGEN I

HÖGSPÄNNINGSKONDENSATORN

Högspänningskondensatorn är laddad i 60 sekunder efter

det att ugnen stängts av. Vänta 60 sekunder och korislut

sedan kondensatoms anslutning (dvs anslutningen till

högspänningslikriktaren) till chassiet med hjälp av en isolerad

skruvmejsel.

Sharp rekommenderar att felsökning sker med strömmen

fränkopplad. Ibland kan det var nödvändigt att koppla på

strömmen efter det att höljet avlägsnats, utför da 3 Steg

kontrollen och koppla sedan från ledarna till transformatorns

primärsida. Se till att ledarna är isolerade från andra

komponenter och chassiet. (Använd isoleringsband om det

behövs). När Du testat färdigt utför Du 3 Steg kontrollen och

ansluter ledningarna till transformatorns primärsida igen.

KOM IHÅG ATT KONTROLLERA 4 STEG

1) Anslut alla ledningar som använts vid testning

2) Sätt tillbaka ytterhöljet.

3) Anslut strömkällan på nytt.

4) Sätt på ugnen. Kontrollera alla funktioner.

Mikrovågsugnar får inte användas tomma. Kontrollera

mikrovågsstrålningen i olika delar av ugnen genom att placera

en kopp med kallt vatten på ugnens tallrik, stäng dörren, ställ

in HIGH och ställ in 2 minuter på timern. När två minuter har gått

(timem visar 0) kontrollerar du om vattnet är varmt. Om vattnet

fortfarande är kallt utför Du 3 steg kontroller och kontrollerar

anslutningarna till varje enskild komponent på nytt.

När all service är klar och ugnen ihopskruvad skall ugnens

uteffekt och eventuellt mikrovågsläckage kontrolleras.

R-25AM

II forni a microonde contengono un circuito elettrico in grado di generare tensioni e correnti estremamente elevate.

L’eventuale contatto con i seguenti componenti può causare la folgorazione:

condensatore ad alta tensione; trasformatore ad alta tensione; magnetron; rettificatore alta tensione; cablaggio ad

alta tensione.

TRE OPERAZIONI IMPORTANTI PER

INCOMINCIARE

1) Scollegare l'alimentazione elettrica.

2) Verificare che la porta sia bloccata in posizione

aperta.

3) Scaricare il condensatore ad alta tensione.

ATTENZIONE AL CONDENSATORE AD ALTA

TENSIONE: PUO ESSERE CARICO

Il condensatore ad alta tensione rimane carico per circa

60 secondi dopo lo spegnimento del forno. Occorre quindi

spettare 60 secondi prima di cortocircuitare, utilizzando

un cacciavite con impugnatura isolata, il collegamento

del condensatore ad alta tensione (cioè del conduttore

di collegamento del raddrizzatore ad alta tensione) sul

telaio del forno.

Sharp raccomanda, nei limiti del possibile, che la ricerca

dei guasti avvenga in assenza di alimentazione elettrica.

In alcuni casi tuttavia, può essere necessario alimentare

l'apparecchio dopo aver rimosso la scatola esterna. In

questo caso eseguire i tre controlli sopra citati e quindi

scollegare i connettori dal primario del trasformatore.

Assicurarsi che tali connettori non vengano a contatto con

altri componenti, ne con il telaio del forno (fare uso, se

necessario, di nastro isolante). Al termine dell'intervento,

eseguire nuovamente i tre controlli e ricollegare i conduttori

al primario del trasformatore.

QUATTRO VERIFICHE IMPORTANTI DA NON

DIMENTICARE

1) Ricollegare tutti i conduttori staccati dai vari componenti

durante l'intervento.

2) Rimontare la scatola esterna.

3) Ripristinare l'alimentazione elettrica.

4) Rimettere in funzione il forno. Controllare tutte le funzioni.

I forni a microonde non devono mai funzionare a vuoto. Per

verificare la presenza di energia da microonde all'interno

di una cavitá, mettere una tazza di acqua fredda sul piatto

rotante del forno, chiudere la porta, regolare la potenza su

HIGH ed impostate il temporizzatore su due (2) minuti.

Trascorsi i due minuti (temporizzatore a zero), controllare

accuratamente che ora l'acqua sia calda. Se l'acqua è

rimasta fredda, eseguire i tre controlli iniziali e verificare

nuovamente i collegamenti del componente in questione.

Dopo aver portato a termine le operazioni di manutenzione

e rimontato il forno, è necessario controllare la potenza delle

microonde emesse ed eseguire un test per verificare che

non vi sia alcuna dispersione.

R-25AM

GENERAL INFORMATION

WARNING

THIS APPLIANCE MUST BE EARTHED

IMPORTANT

THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

PRODUCT DESCRIPTION

SPECIFICATION

ITEM DESCRIPTION

Power Requirements 230 Volts

50 Hertz

Single phase, 3 wire earthed

Power Comsumption

3.15 kW Approx. 15 A

Power Output

2100 W nominal of RF microwave energy (measured by method of IEC 60705)

Operating frequency 2450 MHz

Case Dimensions Width 510mm

Height 335 mm

Depth 470mm

Cooking Cavity Dimensions Width 330 mm

Height 180 mm

Depth 330mm

Control Complement Electronic Timer (0 - 30 minutes)

Microwave Power level

100% 50% 20% 10%

NOTE: The maximum cooking time for 100% or 50% is 15 minutes.

If the time you set exceeds a maximum time, the display will

show "EE9".

MICROWAVE POWER LEVEL buttons

START button

Set Weight Approx. 33 kg

R-25AM

APPEARANCE VIEW

OVEN

1. Control panel

2. Hole for safety door latches

3. Ceramic floor

4. Splash cover

5. Oven light

6. Air intake filter

7. Air intake openings

8. Oven cavity

9. Door seals and sealing surfaces

10. Door hinges

11. Oven door with see-through window

12. Door safety latches

13. Door handle.

14. Outer cabinet

15. Removable cover over oven light bulb

16. Air vent openings

17. Power supply cord

18 Mounting plate

19 Screw for mounting plate

DISPLAY AND INDICATORS

Check indicators after the oven starts

to confirm the oven is operating as

desired.

1. Cook indicator

This indicator shows cooking in progress.

2. Digital display

3. Microwave power level display

OPERATING KEYS

4. HIGH 100%

5. MEDIUM 50%

6. MED LOW 20%

7. DEFROST 10%

8. ELECTRONIC TIMER

Rotate the control to enter cooking time.

9. START button

AUTO TOUCH CONTROL PANEL

INSTALLATION INFORMATION

When this commercial microwave oven is installed near other commercial electrical appliances, connect a lead wire to

each equivalent potential terminal with equipotential marking between them (insert a lead wire between a washer and

an earth angle, and screw them), as shown in Fig. A-1, to make sure that they are at equivalent potential.

If any lead wire is not connected between them, when person touch them he/she will get a electric shock.

Figure A-1

679

COMMERCIAL MICROWAVE OVEN OTHER COMMERCIAL

ELECTRICAL APPLIANCE

Lead wire

Equipotential marking

Earth angle

(Equivalent potential terminal)

Equivalent

potential terminal

Screw

Washer

Lead wire

MICROWAVE

POWER LEVEL

buttons

POWER

R-25AM

OPERATION SEQUENCE

4. When the cooking time is up, a signal tone is heard and

the relays RY3+RY4 go back to their home position.

The circuits to the high voltage transformers T1+T2.

The relay RY1 remains and oven lamp, blower motor

and antenna motors work for 1 minute.

5. When the door is opened during a cook cycle, the

switches come to the following condition.

CONDITION

DURING DOOR OPEN

SWITCH CONTACT COOKING

(NO COOKING)

Interlock switches COM-NO Closed Open

Monitor switches COM-NC Open Closed

Stop switch COM-NO Closed Open

The circuits to the high voltage transformers T1+T2 are

cut off when the interlock and stop switches

SW1+SW2+SW5 are made open. The blower motor BM,

antenna motors and oven lamp remains on even if the

oven door is opened after the cooking cycle has been

interrupted, because the relay RY1 stays closed. Shown

in the display is the remaining time, but the program is

cancelled if the oven is not started within 1 minute.

6. MONITOR SWITCH CIRCUIT

The monitor switches SW3+SW4 are mechanically

controlled by oven door, and monitors the operation of

the interlock switches SW1+SW2.

6-1. When the oven door is opened during or after the

cycle of a cooking program, the interlock switches

SW1+SW2 and stop switches SW5 must open their

contacts first. After that the contacts (COM-NC) of the

monitor switches SW3+SW4 can be closed.

6-2. When the oven door is closed, the contacts (COM-

NC) of the monitor switches SW3+SW4 must be

opened first. After that the contacts (COM-NO) of the

interlock switches SW1+SW2 and stop switch SW5

must be closed.

6-3. When the oven door is opened and the contacts of the

interlock switch SW1 (or SW2) remain closed, re-

mains closed, the fuse F1 F10A (or F2 F10A) will

blow, because the monitor switch SW3 (or SW4) is

closed and a short circuit is caused.

MICROWAVE VARIABLE COOKING

When the microwave oven is preset for variable cooking

power, the line voltage is supplied to the high voltage

transformers T1+T2 intermittently within a 48 second time

base through the contacts of the relays RY3+RY4.

The following levels of microwaves power are given.

Closing the door activates all door interlock switches

(interlock switches and stop switch).

IMPORTANT

When the oven door is closed, the monitor switch contacts

COM-NC must be open. When the microwave oven is

plugged in a wall outlet (230 volts, 50Hz), the line voltage

is supplied to the control unit through the noise filter.

Figure O-1 on page 34

1. The digital display shows . 0

IDLE CONDITION

When the door is opened, the contacts of the interlock

switches SW1+SW2 and stop switch SW5 open, initiating

the following:

Figure O-2 on page 34

1. A signal is input to the control unit energizing the coil of

shut-off relay RY-1.

2. The shut-off relay RY-1 contacts close completing

circuits to turn on the oven lamp, blower motor and

antenna motors.

3. If the door remains open, 60 seconds later the control

unit de-energizes shut-off relay RY-1 turning off the

oven lamp, blower motor and antenna motors.

When the door is closed, the contacts of the interlock switches

SW1+SW2 and stop switch SW5 close. With the closing of the

stop switch SW5 contacts, an additional circuit is provided which

will permit the operation of the oven when one of the touch pads

is depressed. Since the control is enabled through the stop

switch SW5, the door must be closed before the touch pads will

be effective. When the door is closed, a full 60 second IDLE

condition is always provided for selecting and pressing the

desired touch pads. A 60 second IDLE condition will also follow

the end of each cook cycle.

MICROWAVE COOKING CONDITION

Enter a desired cooking time by turning ELECTRONIC

TIMER knob. And then touch START button.

NOTE: The programme is canceled when any buttons

are not touched for more than 3 minutes dur-

ing programming.

Function sequence Figure O-3 on page 35

CONNECTED COMPONENTS RELAY

Oven lamp/ Blower motor/ Antenna motors RY1

High voltage transformer T1 RY3

High voltage transformer T2 RY4

1. The line voltage is supplied to the primary winding of

the two high voltage transformers. The voltage is

converted to about 3.3 volts A.C. output on the filament

winding and high voltage of approximately 2000 volts

A.C. on the secondary winding.

2. The filament winding voltage (3.3 volts) heats the

magnetron filament and the high voltage (2000 volts) is

sent to the voltage doubling circuit, where it is doubled

to negative voltage of approximately 4000 volts D.C..

3. The 2450 MHz microwave energy produced in the magnet-

ron generates a wave length of 12.24 cm. This energy is

channelled through the waveguide (transport channel) into

the oven cavity, where the food is placed to be cooked.

NOTE: The ON/OFF time ratio does not exactly corre-

spond to the percentage of microwave power,

because approx. 3 seconds are needed for heat-

ing up the magnetron filament.

48 sec. ON

10%

26 sec. ON

50%

12 sec. ON

20%

8 sec. ON

10%

R-25AM

TWO MAGNETRON OPERATION SYSTEM

Two magnetrons MG1+MG2 are equipped in order to get

higher microwave power output. The primary windings of

the high voltage transformers T1+T2 are connected so

that each magnetron can be oscillated alternatively ac-

cording to the frequency of the power supply. Refer to the

Figure B-1 and B-2.

Figure B-1. High Voltage Circuit

Figure B-2. Operation of Magnetron

T1: HIGH VOLTAGE

TRANSFORMER

H. V. RECTIFIER

C1: H.V. CAPACITOR

MG1: MAGNETRON (UPPER)

(REAR)

H. V. RECTIFIER

H. V. FUSE H. V. FUSE

C2: H.V. CAPACITOR

MG2: MAGNETRON (LOWER)

T2: HIGH VOLTAGE

TRANSFORMER

(FRONT)

COMMERCIAL

FREQUENCY

(50HZ)

POWER OUTPUT

BY MAGNETRON T1

POWER OUTPUT

BY MAGNETRON T2

OPERATION OF

MAGNETRON

R-25AM

DOOR OPEN MECHANISM

1. The door release lever is pulled.

2. The upper latch head is lifted up by the linked door

release lever.

3. The head lever is lifted up by the door release lever.

4. The joint lever is lifted up by the head lever.

5. The lower latch head is lifted up by the joint lever.

6. Now both latch heads are lifted up, so they can be

released from the latch hook.

7. Now the door can be opened.

Figure D-1. Door Open Mechanism

INTERLOCK SWITCHES SW1, SW2 AND STOP

SWITCH SW5

1. When the oven door is closed, the contacts COM-NO

must be closed.

2. When the oven door is opened, the contacts COM-NO

must be opened.

MONITOR SWITCHES SW3, SW4

The monitor switches SW3, SW4 are activated (the con-

tacts opened) the upper latch head and switch lever A

while the door is closed. The switch SW3 (or SW4) is

intended to render the oven inoperative by means of

blowing the fuse F1 F10A (or F2 F10A) when the contacts

of the interlock switch SW1 (or SW2) fail to open when the

door is opened.

Function

1. When the door is opened, the monitor switches SW3

+SW4 contacts close (to the ON condition) due to their

being normally closed. At this time the interlock switch

SW1+SW2 are in the OFF condition (contacts open)

due to their being normally open contact switches.

2. As the door goes to a closed position, the monitor

switches SW3+SW4 contacts are opened and inter-

lock switch SW1+SW2 contacts are closed (On open-

ing the door, each of these switches operate inversely.)

3. If the door is opened and the interlock switch SW1 (or

SW2) contacts fail to open, the fuse F1 F10A (or F2

F10A) blows simultaneously with closing of the monitor

switch SW3 (or SW4) contacts.

FUNCTION OF IMPORTANT COMPONENTS

CAUTION:BEFORE REPLACING A BLOWN FUSE F1

F10A (OR F2 F10A) TEST THE INTERLOCK

SWITCH SW1 (OR SW2) AND MONITOR

SWITCHE SW3 (OR SW4) FOR PROPER

OPERATION. (REFER TO CHAPTER “TEST

PROCEDURE”).

NOISE FILTER

The noise filter assembly prevents radio frequency inter-

ference that might flow back in the power circuit.

FUSES F1, F2 F10A 250V

1. If the wire harness or electrical components are short-

circuited, this fuse blows to prevent an electric shock or

fire hazard.

2. The fuse F1 F10A (or F2 F10A) also blows when

interlock switch SW1 (or SW2) remains closed with the

oven door open and when the monitor switches SW3

(or SW4) closes.

WEAK POINT F3

If the wire harness or electrical components make a short-

circuit, this weak point F3 blows to prevent an electric

shock or fire hazard.

HIGH VOLTAGE FUSE(S) F4, F5

The high voltage fuse blows when the high voltage rectifier

or the magnetron is shorted.

MAGNETRON TEMPERATURE FUSES TF1, TF2

The temperature fuses TF1, TF2 located on the top of the

upper and lower waveguide, are designed to prevent

damage to the magnetrons MG1, MG2. If an over heated

condition develops in the tube due to blower motor failure,

obstructed air ducts, dirty or blocked air intake, etc., the

circuit to the magnetrons are interrupted. Under normal

operation, the temperature fuses remains closed. How-

ever, when abnormally high temperatures are generated

within the magnetrons, the temperature fuses will open at

150˚C causing the microwave energy to stop. The defec-

tive temperature fuses must be replaced with new rated

ones.

EXHAUST TEMPERATURE FUSE TF3

The temperature fuse TF3, located on the side of the

exhaust duct assembly, is designed to prevent damage to

the oven by fire. If the food load is overcooked, by either

error in cook time or defect in the control unit, the tempera-

ture fuse will open. Under normal operation, the oven

temperature fuse remains closed. However, when abnor-

mally high temperatures are generated within the oven

cavity, the oven temperature fuse will open at 120˚C,

causing the oven to shut down. The defective temperature

fuse must be replaced with new rated one.

EXHAUST OVEN THERMISTOR TH3

The thermistor is a negative temperature coefficient type.

The temperature in the exhaust duct is detected through

the resistance of the thermistor.

If the temperature is high, the control panel will display

“EE7” and the oven will stop to avoid overheating and

Latch head

SW4: Monitor switch

(Oven side)

SW3: Monitor switch

Latch hook

SW1: Interlock switch

SW2: Interlock switch

(Oven side)

SW5: Stop switch

Latch head

Joint lever

Door release

lever

Head lever

R-25AM

catching fire.

If the thermistor is open, the control panel will display

"EE6" and the oven will stop.

MAGNETRON THERMISTORS TH1, TH2

The thermistor is a negative temperature coefficient type.

The air temperature around the magnetron is detected

through the resistance of the thermistor.

If the temperature is high, the control panel will display

"EE17" and the oven will stop to protect the lower magn-

etron against overheat.

If the magnetron thermistor is open, the control panel will

display "EE16" and the oven will stop.

If the magnetron thermistor is short, the control panel will

display "EE19" and the oven will stop.

BLOWER MOTOR BM

The blower motor BM drives a blade which draws external

cool air into the oven. This cool air is directed through the

air vanes surrounding the magnetrons and cools the

magnetrons. This air is channelled through the oven cavity

to remove steam and vapours given off from the heating

foods. It is then exhausted through the exhausting air

vents at the oven cavity.

ANTENNA MOTORS SM

The upper and lower antenna motors SM drive stirrer

antennas.

OVEN LAMP OL

The oven cavity light illuminates the interior of the oven so

that food being cooked can be examined visually through the

door window without having to open the door. The oven lamp

is on during the cooking cycle and idle condition.

TROUBLESHOOTING GUIDE

When troubleshooting the microwave oven, it is helpful to follow the Sequence of Operation in performing the checks.

Many of the possible causes of trouble will require that a specific test be performed. These tests are given a procedure

letter which will be found in the “Test Procedure”section.

IMPORTANT: If the oven becomes inoperative because of a blown fuse F1 F10A (or F2 F10A) in the interlock switch

SW1 (or SW2) - monitor switches SW3 (or SW4) , check the interlock switch SW1 (or SW2) and monitor

switches SW3 (or SW4) before replacing the fuse F1 F10A (or F2 F10A).

R-25AM

. does not appear on display when power cord is plugged into

wall outlet.

Control panel can not accept buttons or timer in.

Fuse F1 or F2 blows when the door is opened.

Home fuse blows when power cord is plugged into wall outlet.

Weak point F3 blows when power cord is plugged into wall outlet.

Oven lamp, fan motor and antenna motors do not work for 1

minute when the door is opened or after cooking.

Fuse F1 or F2 blows when power cord is plugged into wall outlet.

Oven lamp does not light when door is opened. (Blower and antenna

motors work)

Blower motor does not work when door is opened. (Oven lamp

lights and antenna motors work)

EE 1 (Magnetron MG1 failure)

EE 2 (Magnetron MG2 failure)

EE 3 (Magnetron MG1 and MG2 failure)

EE 6 (Exhaust thermistoropen)

EE 7 (Exhaust air temperature is high)

EE 9 (Exceeded max. heating time)

Oven lamp, blower motor and antenna motors do not work.

Oven lamp does not work.

Blower motor does not work.

Oven does not stop after end of cooking cycle.

Home fuse blows when starting the oven.

Oven goes into cook cycle but shuts down before end of cooking cycle.

It passed more than 1 minute after cooking but oven lamp, blower

motor and stirrer motors do not stop.

EE 16 (Thermistor of magnetron are open.)

EE 17 (Magnetron temperature is high.)

EE 19 (Magnetron thermistor short)

EE 10 (Fault of memory)

Antenna motors do not work.

TESTPROCEDURE

POSSIBLE CAUSE

AND

DEFECTIVE PARTS

CONDITION

OFF

CONDITION

PROBLEM

EEP ROM I-2

N SWITCH UNIT

TOUCH CONTROL TRANSFORMER T3

Due to programme lock

Over the max. cooking time

No power at wall outlet

HOME FUSE or BREAKER

Mis adjustment of switches

P FUSE 2.5A

O RELAY RY-4

O RELAY RY-3

O RELAY RY-1

M TOUCH CONTROL PANEL

Opened wire harness

Shorted wire harness

POWER SUPPLY CORD

K NOISE FILTER

OVEN LAMP OR SOCKET

J BLOWER MOTOR BM

J ANTENNA MOTORS SM

I EXHAUST THERMISTOR TH3

I MAGNETRON THERMISTOR (Lower) TH2

I MAGNETRON THERMISTOR (Upper) TH1

L HIGH VOLTAGE FUSE F5

L HIGH VOLTAGE FUSE F4

H EXHAUST TEMPERATURE FUSE TF3

H MAGNETRON TEMPERATURE FUSE TF2

H MAGNETRON TEMPERATURE FUSE TF1

F WEAK POINT F3

G FUSE F10A F2

G FUSE F10A F1

E STOP SWITCH SW5

E MONITOR SWITCH SW4

E MONITOR SWITCH SW3

E INTERLOCK SWITCH SW2

D INTERLOCK SWITCH SW1

D H.V. CAPACITOR C2

D H.V. CAPACITOR C1

H.V. WIRE HARNESS

C H.V. RECTIFIER ASSEMBLY FOR MG2

C H.V. RECTIFIER ASSEMBLY FOR MG1

B HIGH VOLTAGE TRANSFORMER T2 (Rear)

B HIGH VOLTAGE TRANSFORMER T1 (Front)

A MAGNETRON MG2 (Lower)

A MAGNETRON MG1 (Upper)

R-25AM

A MAGNETRON TEST

TEST PROCEDURES

PROCEDURE

LETTER COMPONENT TEST

CARRY OUT

3D CHECKS.

Isolate the magnetron from high voltage circuit by removing all leads connected to filament terminal.

To test for an open circuit filament use an ohmmeter to make a continuity test between the magnetron

filament terminals, the meter should show a reading of less than 1 ohm.

To test for short circuit filament to anode condition, connect ohmmeter between one of the filament

terminals and the case of the magnetron (ground). This test should be indicated an infinite resistance.

If a low or zero resistance reading is obtained then the magnetron should be replaced.

MICROWAVE OUTPUT POWER (1 litre water load)

The following test procedure should be carried out with the microwave oven in a fully assembled

condition (outer case fitted). Microwave output power from the magnetron can be measured by way

of IEC 60705, i.e. it is measured by how much power the water load can absorb. To measure the

microwave output power in the microwave oven, the relation of calorie and watt is used. When P(W)

heating works for t(second), approximately P x t/4.187 calorie is generated. On the other hand, if the

temperature of the water with V(ml) rises ∆T (°C) during this microwave heating period, the calorie of

the water is V x ∆T.

Measuring condition:

1. Container

The water container must be a cylindrical borosilicate glass vessel having a maximum material

thickness of 3 mm and an outside diameter of approximately 190 mm.

2. Temperature of the oven and vessel

The oven and the empty vessel are at ambient temperature prior to the start the test.

3. Temperature of the water

The initial temperature of the water is (10±1)°C.

4. Select the initial and final water temperature so that the maximum difference between the final water

temperature and the ambient temperature is 5°C.

5. Select stirring devices and measuring instruments in order to minimize addition or removal of heat.

6. The graduation of the thermometer must be scaled by 0.1°C at minimum and be an accurate

thermometer.

7. The water load must be (1000±5) g.

8. “t” is measured while the microwave generator is operating at full power. Magnetron filament heat-

up time is not included.

NOTE: The operation time of the microwave oven is “t + 3” sec. (3 sec. is magnetron filament heat-up time.)

Measuring method:

1. Measure the initial temperature of the water before the water is added to the vessel.

(Example: The initial temperature T1 = 11°C)

2. Add the 1 litre water to the vessel.

3. Place the load on the centre of the shelf.

4. Operate the microwave oven at HIGH until the temperature of the water rises by a value ∆ T of

(10 ± 2) K.

5. Stir the water to equalize temperature throughout the vessel.

6. Measure the final water temperature. (Example: The final temperature T2 = 21°C)

7. Calculate the microwave power output P in watts from above formula.

NEVER TOUCH ANY PART IN THE CIRCUIT WITH YOUR HAND OR AN INSULATED TOOL

WHILE THE OVEN IS IN OPERATION.

The formula is as follows;

P x t / 4.187 = V x ∆ T+ 0.55 x mc (T2-T0) P (W) = 4.187 x V x ∆T / t + 0.55 x mc (T2-T0)/t

Our condition for water load is as follows:

Room temperature (T0) ...... around 20°CPower supply Voltage .............. Rated voltage

Water load.....................................1000 g Initial temperature (T1) ...................... 10±1°C

Heating time ................................. 20 sec. Mass of container (mc) ......................... 330 g

T2 ............... Final temperature P = 210 x ∆T+ 0.55 x mc(T2-T0)/20

R-25AM

Room temperature ................................................................................................. T0 = 21°C

Initial temperature .................................................................................................. T1 = 11°C

Temperature after (20 + 3) = 23 sec ...................................................................... T2 = 21°C

Temperature difference Cold-Warm...................................................................... ∆T1 = 10˚C

Measured output power

The equation is “P = 210 x ∆T” ................................................ P = 210 x 10°C = 2100 Watts

JUDGMENT: The measured output power should be within the range of ± 15 % of the rated output

power.

CAUTION: 1°C CORRESPONDS TO 210 WATTS. REPEAT MEASUREMENT IF THE POWER IS

INSUFFICIENT.

TEST PROCEDURES

PROCEDURE

LETTER COMPONENT TEST

Heat up for 23 sec.

B HIGH VOLTAGE TRANSFORMER TEST

WARNING: High voltage and large currents are present at the secondary winding and

filament winding of the high voltage transformer. It is very dangerous to work

near this part when the oven is on. NEVER make any voltage measurements

of the high-voltage circuits, including the magnetron filament.

CARRY OUT 3D CHECKS.

Disconnect the leads to the primary winding of the high voltage transformer. Disconnect the filament

and secondary winding connections from the rest of the HV circuitry. Using an ohmmeter, set on a low

range, it is possible to check the continuity of all three windings. The following readings should be

obtained:-

a. Primary winding approximately 1.2 Ω

b. Secondary winding approximately 75 Ω

c. Filament winding less than 1 Ω

If the readings obtained are not stated as above, then the high voltage transformer is probably faulty

and should be replaced.

CARRY OUT 4R CHECKS.

CARRY OUT 3D CHECKS.

Isolate the high voltage rectifier assembly from the HV circuit. The high voltage rectifier can be tested

using an ohmmeter set to its highest range. Connect the ohmmeter across the terminal B+C of the high

voltage rectifier and note the reading obtained. Reverse the meter leads and note this second reading.

The normal resistance is infinite in one direction and more than 100 kΩ in the other direction.

CARRY OUT 4R CHECKS.

NOTE: FOR MEASUREMENT OF THE RESISTANCE OF THE RECTIFIER, THE BATTERIES OF

THE MEASURING INSTRUMENT MUST HAVE A VOLTAGE AT LEAST 6 VOLTS, BECAUSE

OTHERWISE AN INFINITE RESISTANCE MIGHT BE SHOWN IN BOTH DIRECTIONS.

C HIGH VOLTAGE RECTIFIER ASSEMBLY TEST

HIGH VOLTAGE RECTIFIER

1000g

T1˚C

T2˚C

R-25AM

F WEAK POINT F3 TEST

CARRY OUT 3D CHECKS.

If the weak point F3 is blown, there could be a shorts or grounds in electrical parts or wire harness.

Check them and replace the defective parts or repair the wire harness.

CARRY OUT 4R CHECKS.

CAUTION: Only replace weak point F3 with the correct value replacement.

If incorrect readings are obtained, make the necessary switch adjustment or replace the switch.

CARRY OUT 4R CHECKS.

G FUSE F1, F2 F10A TEST

CARRY OUT 3D CHECKS.

If the fuse F1 F10A (or F2 F10A) is blown when the door is opened, check the interlock switch SW1

(or SW2) and monitor switch SW3 (or SW4).

If thefuse F1 F10A (or F2 F10A) is blown by incorrect door switching replace the defective switch(s)

and the fuse F1 F10A (or F2 F10A).

CARRY OUT 4R CHECKS.

CAUTION: Only replace fuse F1 F10A (or F2 F10A) with the correct value replacement.

H TEMPERATURE FUSE TF1, TF2, TF3 TEST

TEST PROCEDURES

PROCEDURE

LETTER COMPONENT TEST

E SWITCH TEST

CARRY OUT 3D CHECKS.

Isolate the switch to be tested and using an ohmmeter check between the terminals as described in

the following table.

D HIGH VOLTAGE CAPACITOR TEST

CARRY OUT 3D CHECKS.

A. Isolate the high voltage capacitor from the circuit.

B. Continuity check must be carried out with measuring instrument which is set to the highest

resistance range.

C. A normal capacitor shows continuity for a short time (kick) and then a resistance of about 10MΩ

after it has been charged.

D. A short-circuited capacitor shows continuity all the time.

E. An open capacitor constantly shows a resistance about 10 MΩ because of its internal 10MΩ

resistance.

F. When the internal wire is opened in the high voltage capacitor shows an infinite resistance.

G. The resistance across all the terminals and the chassis must be infinite when the capacitor is

normal.

If incorrect reading are obtained, the high voltage capacitor must be replaced.

CARRY OUT 4R CHECKS.

Table: Terminal Connection of Switch

Plunger Operation COM to NO COM to NC

Released Open circuit Short circuit

Depressed Short circuit Open circuit

COM; Common terminal,

NO; Normally open terminal

NC; Normally close terminal

1. CARRY OUT 3D CHECKS.

2. A continuity check across the temperature fuse terminals should indicate a closed circuit unless the

temperature of the temperature fuse reaches specfied temperature as shown below.

R-25AM

TEST PROCEDURES

PROCEDURE

LETTER COMPONENT TEST

3. CARRY OUT

4R CHECKS.

CAUTION: IF THE temperature fuse INDICATES AN OPEN CIRCUIT AT ROOM TEMPERATURE,

REPLACE temperature fuse.

1. CARRY OUT 3D CHECKS.

2. Follow the procedures below for each thermistor.

2-1. THERMISTOR TEST

Disconnect the connector of the thermistor from the switch harness. Measure the resistance of the

magnetron thermistor with an ohmmeter. Connect the ohmmeter leads to the leads of the thermistor.

Resistance: Approx. 500 kΩ -- 1 MΩ

If the meter does not indicate above resistance, replace the thermistor.

3. CARRY OUT 4R CHECKS.

I THERMISTOR TH1, TH2, TH3 TEST

Open Close Display or

temperature temperature Condition Check point

Magnetron tem-

perature fuse (Up-

per)

TF1

Magnetron tem-

perature fuse

(Lower)

TF2

Exhaust tempera-

ture fuse

TF3

150˚C

120˚C

Non resetable

type

Non resetable

type

EE1

EE3

EE2

Oven shut

off

Magnetron

MG1 Failure:

Test magnetron

MG1 and Blower motor.

Magnetron MG1, MG2 Failure: Test magnetron MG1,

MG2. Check blower motor and ventilation opening.

Magnetron MG2 Failure:

Test magnetron

MG2 and Blower motor.

Food has been burned in oven.

Temperature of oven inside is very high.

J MOTOR WINDING TEST

CARRY OUT 3D CHECKS.

Disconnect the leads from the motor. Using an ohmmeter, check the resistance between the two

terminals.

Resistance of Blower motor should be approximately 60Ω.

Resistance of Antenna motor should be approximately 8.8 kΩ.

If incorrect readings are obtained, replace the motor.

CARRY OUT 4R CHECKS.

If incorrect readings are absorbed, replace the noise filter.

CARRY OUT 4R CHECKS.

K NOISE FILTER TEST

CARRY OUT 3D CHECKS.

Disconnect the leads from the terminals of noise filter. Using an ohmmeter, check between the

terminals as described in the following table.

MEASURING POINT INDICATION OF OHMMETER

Between N and L Approx. 680 kΩ

Between terminal N and WHIT Short circuit

Between terminal L and BLK Short circuit

F3 : WEAK POINT

NOISE FILTER

NOISE SUPPRESSION COIL

DISCHARGE RESISTOR 680 kΩ 1/2W

DISCHARGE RESISTOR 10 MΩ 1/2W

LINE CROSS CAPACITOR 0.22µF/ AC250V

LINE CROSS CAPACITOR

10000 pF/ AC250V

LINE CROSS CAPACITOR

10000 pF/ AC250V

BLK

WHT

L HIGH VOLTAGE FUSE F4, F5 TEST

CARRY OUT 3D CHECKS.

If the high voltage fuse F4 (or F5) is blown, there could be a short in the high voltage rectifier or the magnetron

MG1 (or MG2). Check them and replace the defective parts and the high voltage fuse F4 (or F5).

CARRY OUT 4R CHECKS.

CAUTION: Only replace high voltage fuse with the correct value replacement.

R-25AM

M TOUCH CONTROL PANEL ASSEMBLY TEST

TEST PROCEDURES

PROCEDURE

LETTER COMPONENT TEST

The touch control panel consists of circuits including semiconductors such as LSI etc. Therefore,

unlike conventional microwave ovens, proper maintenance cannot be performed with only a

voltmeter and ohmmeter. In this service manual, the touch control panel assembly is divided into three

units, Control Unit, Switch Unit and Encoder Unit troubleshooting by unit replacement is described

according to the symptoms indicated.

1. Switch Unit Note :Check the lead wire harness connections among big and small switch units

and control unit before replacement.

The following symptoms indicate a defective switch unit. Replace the switch unit.

a) When touching the buttons, a certain button produces no signal at all.

b) When touching the buttons, sometimes a button produces no signal.

2. Encoder Note : Check the lead wire connection between encoder and control unit before

replacement.

The following symptoms indicate a defective encoder. Replace the encoder.

a) When rotating the encoder, the cooking time can not be entered.

3. Control Unit

The following symptoms may indicate a defective control unit. Replacing the control unit. Before

replacing the control unit, perform the switch unit test (Procedure N) to determine if control unit is

faulty.

3-1 Programming problems.

a) When touching the buttons, a certain group of buttons do not produce a signal.

3-2 Display problems.

a) For a certain digit, all or some segments do not light up.

b) For a certain digit, brightness is low.

c) Only one indicator does not light.

d) The corresponding segments of all digits do not light up; or they continue to light up.

e) Wrong figure appears.

f) A certain group of indicators do not light up.

g) The figure of all digits flicker.

3-3 Other possible problems caused by defective control unit.

a) Buzzer does not sound or continues to sound.

b) Cooking is not possible.

1. CARRY OUT

3D CHECKS.

2. Remove the switch unit from the control panel, referring to control panel removal.

3. To test the switches (SW1-SW5) on the switch unit, check between the terminals of the connector

CN-F as described in the following table by using ohmmeter when the switches are released and

depressed.

Switches Terminals Released Depressed

SW1 F1 - F4 O.C. S.C.

SW2 F1 - F5 O.C. S.C.

SW3 F2 - F4 O.C. S.C.

SW4 F2 - F5 O.C. S.C.

SW5 F3 - F4 O.C. S.C.

4. If incorrect readings are obtained, replace the defective switch.

5. CARRY OUT 4R CHECKS.

N SWITCH UNIT TEST

O RELAY TEST

CARRY OUT 3D CHECKS.

Remove the outer case and check voltage between Pin Nos. 3 and 5 of the connector (A) on the control

unit with an A.C. voltmeter. The meter should indicate 230 volts, if not check control unit circuity.

O.C. ----- Open Circuit

S.C. ----- Short Circuit

R-25AM

TEST PROCEDURES

PROCEDURE

LETTER COMPONENT TEST

RY1, RY3 and RY4 Relay Test

These relays are operated by D.C. voltage.

Check voltage at the relay coil with a D.C. voltmeter during the microwave cooking operation.

DC. voltage indicated .............................Defective relay.

DC. voltage not indicated .......................Check diode which is connected to the relay coil. If

diode is good, control unit is defective.

RELAY SYMBOL OPERATIONAL VOLTAGE CONNECTED COMPONENTS

RY1 APPROX. 25.9V D.C. Oven lamp, Blower motor and Antenna motors

RY3 APPROX. 25.0V D.C. High voltage transformer (MG1)

RY4 APPROX. 25.0V D.C. High voltage transformer (MG2)

CARRY OUT 4R CHECKS.

To protect the electronic circuits, this model is provided with a fine fuse added to the primary on the

PWB. If the fuse is open, follow the troubleshooting guide given below for repair.

Problem: POWER ON, indicator does not light up.

CARRY OUT 3D CHECKS.

STEPS OCCURRENCE CAUSE OR CORRECTION

1 The rated AC voltage is not present at Check supply voltage and oven power cord.

POWER terminal of CPU connector (CN-A).

2 The rated AC voltage is present at primary Touch control transformer or secondary circuit defective.

side of touch control transformer. Check and repair.

3 Fuse on the PWB is open. Replace the fuse with new one.

(CARRY OUT 3D CHECKS BEFORE REPAIR)

NOTE: *At the time of these repairs, make a visual inspection of the varistor for burning damage

and examine the transformer with tester for the presence of layer short-circuit (check

primary coil resistance). If any abnormal condition is detected, replace the defective parts.

CARRY OUT 4R CHECKS.

P PROCEDURES TO BE TAKEN WHEN THE FUSE ON THE PRINTED WIRING BOARD(PWB) IS

OPEN

R-25AM

2. Switch Unit

The switch unit is composed of a matrix circuit in which

when a switch it touched, one of signals P30 - P31

generated by the LSI, is passed through the switch

and returned to the LSI as one of signals P24 - P26.

3. Encoder

The encoder converts the signal generated by power

source circuit into the pulse signal, and the pulse

signal is sent to the LSI.

TOUCH CONTROL PANEL ASSEMBLY

OUTLINE OF TOUCH CONTROL PANEL

The touch control section consists of the following units as

shown in the touch control panel circuit.

(1) Control Unit

(2) Switch Unit

(3) Encoder Unit

The principal functions of these units and the signals

communicated among them are explained below.

1. Control Unit

Signal of key touch and oven function control are all

processed by one microcomputer.

1) Power Supply Circuit

This circuit changes output voltage at the secondary

side of the touch control transformer to voltages re-

quired at each part by full wave rectifying circuit,

constant voltage circuit, etc..

2) Reset Circuit

This is an Auto-clear Circuit, i.e., a reset circuit, which

enables IC1 to be activated from initial state.

3) Power Synchronizing Signal Generating Circuit

This is a circuit for generating power synchronizing

signal by virtue of the secondary side output of touch

control transformer.

This signal is used for a basic frequency to time

processing and so on.

4) Clock Circuit

This is a circuit for controlling clock frequency required

for operating I-1.

5) I-1 (Main Processor)

This is a one-chip microcomputer, responsible for

controlling the entire control unit.

6) I-2 (Memory Processor)

This is a memory IC, responsible for memory function.

7) Display Circuit

This is a circuit for driving display tubes by I-1 output.

8) Switch Input Circuit

This is a circuit for transmitting switch input information

to I-1.

9) Sound-body Driving Circuit

This is a circuit for driving sound body by I-1 output.

10) Relay Driving Circuit

This is a circuit for driving output relay by I-1 output.

11) Stop Switch Circuit

This is a circuit for driving I-1 to detect door opening/

closing.

12) Exhaust Air Temperature Detecting Circuit

This is a circuit for transmitting output change of

thermistor (Exhaust thermistor) to I-1.

13) Magnetron Temperature Circuit.

(Detect Noload or Fan Lock)

This is a circuit for transmitting output change of

thermistor (Magnetron thermistor) to I-1.

La pagina sta caricando ...

Sharp R-22AM Manuale utente

Marca: Sharp

Modello: R-22AM

Categoria: Microonde

Tipo: Manuale utente

Questo manuale è adatto anche per

Scarica il pdf

rapporto

in altre lingue

English: Sharp R-22AM User manual

Sharp R-22AM Manuale utente

Questo manuale è adatto anche per

Sharp R-22AM Manuale utente

in altre lingue

Documenti correlati

Altri documenti