Moog Videolarm IRM7T2N Manuale utente

Marca: Moog Videolarm

Modello: IRM7T2N

Categoria: Accessori per telecamere di sicurezza

Tipo: Manuale utente

Questo manuale è adatto anche per

www.videolarm.com

RM7

Vandal-Resistant Recessed Ceiling Dome Housing

Installation and Operation Instructions for the following models:

RM7C2N

IP Network Ready 7” Vandal-Resistant Outdoor Recessed

dome housing, with recessed ceiling mount, clear dome, with

24Vac transformer

RM7T2N IP Network Ready 7” Vandal-Resistant Outdoor Recessed dome

housing, with recessed ceiling mount, tinted dome, with 24Vac

transformer

IRM7C2N IP Network Ready 7” Vandal-Resistant Indoor Recessed dome

housing, with recessed ceiling mount, clear dome, with 24Vac

transformer

IRM7T2N IP Network Ready 7” Vandal-Resistant Indoor Recessed dome

housing, with recessed ceiling mount, tinted dome, with 24Vac

transformer

Before attempting to connect or operate this product,

please read these instructions completely.

CERTIFIED

81-IN5394

01-15-2009

IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS

UNPACKING

SERVICE

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with damp cloth.

7 Do not block any of the ventilation openings. Install in accordance with the

manufacturers instructions.

8 Cable Runs- All cable runs must be within permissible distance.

9 Mounting - This unit must be properly and securely mounted to a supporting

structure capable of sustaining the weight of the unit.

Accordingly:

a. The installation should be made by a qualified installer.

b. The installation should be in compliance with local codes.

c. Care should be exercised to select suitable hardware to install the unit, taking into

account both the composition of the mounting surface and the weight of the

unit.

10 Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus ( including amplifiers) that produce heat.

11 Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding type

plug has two blades and a third grounding prong. The wide blade or the third

prong are provided for your safety. When the provided plug does not fit into your

outlet, consult an electrician for replacement of the obsolete outlet.

12 Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

13 Only use attachment/ accessories specified by the manufacturer.

14 Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

15 Unplug this apparatus during lighting storms or when unused for long periods of time.

16 Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled of objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or

has been dropped.

Be sure to periodically examine the unit and the supporting structure to make sure that the

integrity of the installation is intact. Failure to comply with the foregoing could result in the

unit separating from the support structure and falling, with resultant damages or injury to

anyone or anything struck by the falling unit.

Unpack carefully. Electronic components can be

damaged if improperly handled or dropped. If an item

appears to have been damaged in shipment, replace

it properly in its carton and notify the shipper.

Be sure to save:

1 The shipping carton and packaging material.

They are the safest material in which to make

future shipments of the equipment.

2 These Installation and Operating Instructions.

If technical support or service is needed, contact us

at the following number:

The lightning flash with an arrowhead

symbol, within an equilateral triangle, is

intended to alert the user to the presence

of non-insulated “dangerous voltage”

within the product’s enclosure that may be

of sufficient magnitude to constitute a risk

to persons.

Este símbolo se piensa para alertar al usuario a la

presencia del “voltaje peligroso no-aisIado” dentro del

recinto de los productos que puede ser un riesgo de

choque eléctrico.

Ce symbole est prévu pour alerter I’utilisateur à la

presence “de la tension dangereuse” non-isolée dans la

clôture de produits qui peut être un risque de choc

électrique.

Dieses Symbol soll den Benutzer zum Vorhandensein der

nicht-lsolier “Gefährdungsspannung” innerhalb der

Produkteinschließung alarmieren die eine Gefahr des

elektrischen Schlages sein kann.

Este símbolo é pretendido alertar o usuário à presença

“di tensão perigosa non-isolada” dentro do cerco dos

produtos que pode ser um risco de choque elétrico.

Questo simbolo è inteso per avvertire I’utente alla

presenza “di tensione pericolosa” non-isolata all’interno

della recinzione dei prodotti che può essere un rischio di

scossa elettrica

The exclamation point within an equilateral

triangle is intended to alert the user to

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

Este símbolo del punto del exclamation se piensa para

alertar al usuario a la presencia de instrucciones

importantes en la literatura que acompaña la

aplicación.

Ce symbole de point d’exclamation est prévu pour

alerter l’utilisateur à la presence des instructions

importantes dans la littérature accompagnant

l’appareil.

Dieses Ausruf Punktsymbol soll den Benutzer zum

Vorhandensein de wichtigen Anweisungen in der

Literatur alarmieren, die das Gerät begleitet.

Este símbolo do ponto do exclamation é pretendido

alertar o usuário à presença de instruções importantes

na literatura que acompanha o dispositivo.

Questo simbolo del punto del exclamaton è inteso per

avvertire l’utente alla presenza delle istruzioni importanti

nella letteratura che accompagna l'apparecchio.

TECHNICAL SUPPORT

AVAILABLE 24 HOURS

1- 800 - 554 -1124

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER ( OR BACK). NO USER- SERVICE-

ABLE PARTS INSIDE. REFER SEVICING TO

QUALIFIED SERVICE PERSONNEL.

LIMITED WARRANTY FOR VIDEOLARM INC. PRODUCTS

VIDEOLARM INC. warrants this Product to be free from defects in material or workmanship, as follows:

PRODUCT CATEGORY PARTS LABOR

All Enclosures and Electronics Three (3) Years Three (3) Years

Pan/Tilts Three (3) Years **6 months if used in autoscan Three (3) Years **6 months if used in autoscan

Poles/PoleEvators Three (3) Years Three (3) Years

Warrior/Q-View/I.R. Illuminators Five (5) Years Five (5) Years

Controllers Three (3) Years Three (3) Years

Power Supplies Three (3) Years Three (3) Years

Accessory Brackets Three (3) Years Three (3) Years

During the labor warranty period, to repair the Product, Purchaser will either return the defective product, freight prepaid, or deliver it to Videolarm Inc.

Decatur GA. The Product to be repaired is to be returned in either its original car

ton or a similar package an equal degree of protection with a

RMA # (Return Materials Authorization number) displayed on the outer box or packing slip. To obtain a RMA# you must contact our Technical Support

Team at 800.554.1124, extension 101. Videolarm will return the repaired Product freight prepaid to Purchaser. Videolarm is not obligated to provide

Purchaser with a substitute unit during the warranty period or at any time. After the applicable warranty period, Purchaser must pay all labor and/or

parts charges.

The limited warranty stated in these product instructions is subject to all of the following terms and conditions:

1. NOTIFICATION OF CLAIMS: WARRANTY SERVICE: If Purchaser believes that the Product is defective in material or workmanship, then written notice

with an explanation of the claim shall be given promptly by Purchaser to Videolarm but all claims for warranty service must be made within the

warranty period. If after

investigation Videolarm determines that the reported problem was not covered by the warranty, Purchaser shall pay Videolarm

for the cost of investigating the problem at its then prevailing per incident billable rate. No repair or replacement of any Product or part thereof shall

extend the warranty period as to the entire Product. The

warranty on the repaired part only shall be in for a period of ninety (90) days

following the repair or replacement of that part or the remaining period of the Product parts warranty, whichever is greater.

2. EXCLUSIVE REMEDY: ACCEPTANCE: Purchaser’s exclusive remedy and Videolarm’s sole obligation is to supply (or pay for) all labor necessary to repair

any Product found to be defective within the warranty period and to supply, at no extra charge, new or rebuilt replacements for defective parts.

3. EXCEPTIONS TO LIMITED WARRANTY: Videolarm shall have no liability or obligation to Purchaser with respect to any Product requiring service

during the warranty period which is subjected to any of the following: abuse, improper use: negligence, accident, lightning damage or other acts

of God (i.e., hurricanes, earthquakes),

failure of the end-user to follow the directions outlined in the product instructions, failure of the

end-user to follow the maintenance procedures recommended by the International Security Industry Organization, written in product instructions,

or recommended in the service manual for the Product. Furthermore, Videolarm shall have no liability where a schedule is

for regular

replacement or maintenance or cleaning of certain parts (based on usage) and the end-user has failed to follow such schedule; attempted repair by

personnel; operation of the Product outside of the published environmental and electrical parameters, or if such Product’s original

(trademark, serial number) markings have been defaced, altered, or removed. Videolarm excludes from warranty coverage Products sold

AS IS and/or WITH ALL FAULTS and excludes used Products which have not been sold by Videolarm to the Purchaser. All software and accompanying

documentation furnished with, or as part of the Product is furnished “AS IS”(i.e., without any warranty of any kind), except where expressly provided

otherwise in any documentation or license agreement furnished with the Product.

4. PROOF OF PURCHASE: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.

DISCLAIMER OF WARRANTY

EXCEPT FOR THE FOREGOING WARRANTIES, VIDEOLARM HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,

INCLUDING, BUT NOT LIMITED TO ANY AND/OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY WARRANTY WITH

REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF

THE UNIFORM COMMERCIAL CODE AND/OR IN ANY OTHER COMPARABLE

STATE STATUTE. VIDEOLARM HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON-VIDEOLARM

PRODUCTS OR NON-VIDEOLARM RECOMMENDED PRODUCTS PURCHASER CHOOSES TO CONNECT TO PRODUCT.

LIMITATION OF LIABILITY

THE LIABILITY OF VIDEOLARM, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND

WHATSOEVER, REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF

Index

Specific Camera Instructions:

Axis 213: Block 15

Axis 214: Block 16

Axis 231D/232D: Blocks 17-21

Axis 233D: Blocks 22-26

Canon VB-C10R: Block 27

Canon VB-C50IR: Block 28

Canon VC-C4R/VC-C50IR: Block 29

Elmo PTC 200C: Block 30

Elmo PTC 201: Block 31

Elmo PTC 400C: Block 32

Elmo PTC 401: Block 33

JVC VN-C30U: Block 34

JVC VN-625U/TK-625U: Block 35

JVC VN-C655U: Block 36

Panasonic BB-HCM381/KX-HMC280: Block 37

Pixord 261/262: Block 38

Sony SNCRZ25: Block 39

Sony SNCRZ30: Block 40

Sony SNCRZ50: Block 41

Toshiba IK-WB21A: Block 42

LIMITED WARRANTY FOR VIDEOLARM INC. PRODUCTS

VIDEOLARM INC. warrants this Product to be freefrom defectsin material or workmanship,as follows:

PRODUCTCATEGORY PARTS LABOR

All Enclosures and Electronics Five (5) Years Five (5) Years

Pan/Tilts Three (3) Years **6 months if used in autoscan Three (3) Years **6 months if used in autoscan

Poles/PoleEvators Three (3) Years Three (3) Years

Warrior/Q-View/I.R. Illuminators Five (5) Years Five (5) Years

Controllers Five (5) Years Five (5) Years

Power Supplies Five (5) Years Five (5) Years

Accessory Brackets Five (5) Years Five (5) Years

During the labor warranty period, to repair the Product, Purchaser will either return the defective product, freight prepaid, or deliver it to Videolarm Inc.

Decatur GA. The Product to be repaired is to be returned in either its original carton or a similar package

an equal degree of protection with a

RMA # (Return Materials Authorization number) displayed on the outer box or packing slip. To obtain a RMA# you must contact our Technical Support

Team at 800.554.1124, extension 101. Videolarm will return the repaired Product freight prepaid to Purchaser. Videolarm is not obligated to provide

Purchaser with a substitute unit during the warranty period or at any time. After the applicable warranty period, Purchaser must pay all labor and/or

parts charges.

1.NOTIFICATIONOF CLAIMS: WARRANTYSERVICE: If Purchaser believes that the Product is defective in material or workmanship, then written notice

with an explanation of the claim shall be given promptly by Purchaser to Videolarm but all claims for warranty service must be made within the

warranty period. If after investigation Videolarm determines that the reported problem was not covered by the warranty, P

urchaser shall pay Videolarm

for the cost of investigating the problem at its then prevailing per incident billable rate. No repair or replacement of any Product or part thereof shall

extend the warranty period as to the entire Product. The

warranty on the repaired part only shall be in for a period of ninety (90) days

following the repair or replacement of that part or the remaining period of the Product parts warranty, whichever is greater.

2.EXCLUSIVE REMEDY: ACCEPTANCE:Purchaser’s exclusive remedy and Videolarm’s sole obligation is to supply (or pay for) all labor necessary to repair

any Product found to be defective within the warranty period and to supply, at no extra charge, new or rebuilt replacements for defective parts.

3.EXCEPTIONS TO LIMITED WARRANTY: Videolarm shall have no liability or obligation to Purchaser with respect to any Product requiring service

during the warranty period which is subjected to any of the following: abuse, improper use: negligence, accident, lightning damage or other acts

of God (i.e., hurricanes, earthquakes),

failure of the end-user to follow the directions outlined in the product instructions, failure of the

end-user to follow the maintenance procedures recommended by the International Security Industry Organization, written in product instructions,

or recommended in the service manual for the Product. Furthermore, Videolarm shall have no liability where a schedule is

for regular

replacement or maintenance or cleaning of certain parts (based on usage) and the end-user has failed to follow such schedule; attempted repair by

personnel; operation of the Product outside of the published environmental and electrical parameters, or if such Product’s original

(trademark, serial number) markings have been defaced, altered, or removed. Videolarm excludes from warranty coverage Products sold

AS IS and/or WITH ALL FAULTS and excludes used Products which have not been sold by Videolarm to the Purchaser. All software and accompanying

documentation furnished with, or as part of the Product is furnished “AS IS” (i.e., without any warranty of any kind), except where expressly provided

otherwise in any documentation or license agreement furnished with the Product.

4.PROOF OF PURCHASE: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.

DISCLAIMEROF WARRANTY

EXCEPT FOR THE FOREGOING WARRANTIES, VIDEOLARM HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,

INCLUDING, BUT NOT LIMITED TO ANY AND/OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY WARRANTY WITH

REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF

THE UNIFORM COMMERCIAL CODE AND/OR IN ANY OTHER COMPARABLE

STATE STATUTE. VIDEOLARM HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON-VIDEOLARM

PRODUCTS OR NON-VIDEOLARM RECOMMENDED PRODUCTS PURCHASER CHOOSES TO CONNECT TO PRODUCT.

LIMITATION OF LIABILITY

THE LIABILITY OF VIDEOLARM, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND

WHATSOEVER, REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE

PRODUCT WITH RESPECT TO WHICH SUCH CLAIM IS MADE. IN NO EVENT SHALL VIDEOLARM BE LIABLE TO PURCHASER FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION, REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT

OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.

/tour operation

**6 months if used in autoscan

/tour operation

**6 months if used in autoscan

/tour operation

SView Series Five (5) Years

Five (5) Years

The limited warranty stated in these product instructions is subject to all of the following terms and conditions:

TERMS AND CONDITIONS

RM7C2N

RM7C2

(

OUTDOOR ONLY

)

24 VAC

1.8 Amps

54 Watts

Total Power: 54 Watts

Accessories: Heater: 25 Watts/Blower: 1 Watt

Camera Power: 28 Watts

Tools Required: .100” Flat Head Screwdriver

Phillips Head Screwdriver

Note: IRM7CN includes no accessories

24 VAC

1.8 amperios

54 vatios

Energía Total: 54 vatios

Accesorios: Calentador: 25 Watts/Blower: 1 vatio

Energía De la Cámara fotográfica: 28 vatios

Las Herramientas Requirieron: Destornillador Principal Plano Del 100"

Destornillador Principal Phillips

Nota: IRM7CN no incluye ningún accesorio

24 VCA

1.8 ampères

54 watts

Puissance Totale : 54 watts

Accessoires : Réchauffeur : 25 Watts/Blower : 1 watt

Puissance D'Appareil-photo : 28 watts

Les Outils besoin : Tournevis Principal Plat De 100"

Tournevis Principal Phillips

Note : IRM7CN n'inclut aucun accessoire

24 VAC

1.8 Ampere

54 Watt

Gesamtenergie: 54 Watt

Zusatzgeräte: Heizung: 25 Watts/Blower: 1 Watt

Kamera-Energie: 28 Watt

Werkzeuge Erforderten: 100"Flacher Hauptschraubenzieher

Kreuzkopfhauptschraubenzieher

Anmerkung: IRM7CN schließt keine Zusatzgeräte mit ein

24 VAC

1.8 ampères

54 watts

Poder Total: 54 watts

Acessórios: Calefator: 25 Watts/Blower: 1 watt

Poder Da Câmera: 28 watt

As Ferramentas Requereram: Chave de fenda Principal Lisa Do 100"

Chave de fenda Principal Phillips

Nota: IRM7CN não inclui nenhum acessório

24 VAC

1.8 ampère

54 watt

Alimentazione Totale: 54 watt

Accessori: Riscaldatore: 25 Watts/Blower: 1 watt

Alimentazione Della Macchina fotografica: 28 watt

Attrezzi Richiesti: Cacciavite Capo Piano Del 100"

Cacciavite Capo "phillips"

Nota: IRM7CN non include accessori

Electrical Specifications

IRM7C2N (INDOOR ONLY)

Power 24VAC

Class 2 Only

24 VAC

No power options provided.

Power required for camera only.

24 VAC

Ningunas opciones de la energía proporcionaron.

Energía requerida para la cámara fotográfica solamente.

24 VCA

Option de puissance n'a pas fourni.

Puissance requise pour l'appareil-photo seulement.

24 VAC

Keine Energie Wahlen stellten zur Verfügung.

Energie erfordert für nur Kamera.

24 VAC

Nenhumas opções do poder fornecidas.

Poder requerido para a câmera somente.

24 VAC

Nessun'opzione di alimentazione ha fornito.

Alimentazione richiesta per la macchina fotografica soltanto.

Français

Deutsch

Italiano

Portuguese

Español

English

Contents of Box

Using the provided template, mark the

ceiling tile for the cutout.

• Con la plantilla proporcionada, cortar el azulejo del

techo para el agujero.

• En utilisant le calibre fourni, marquez la tuile de

plafond pour le coupe-circuit.

• Mit der zur Verfügung gestellten Schablone

kennzeichnen Sie die Decke Fliese für den Ausschnitt.

• Usando o molde fornecido, marque a telha do teto

para o entalhe.

• Usando la mascherina fornita, contrassegni le

mattonelle del soffitto per il ritaglio.

10.375”

A box cutter or jigsaw can be used for

cutting the circle.

• Un cortador o un rompecabezas de la caja se

puede utilizar para cortar el círculo.

• Un coupeur ou une scie sauteuse de boîte peut

être utilisé pour couper le cercle.

• Ein Kastenscherblock oder -tischlerbandsäge

können für den Schnitt des Kreises benutzt werden.

• Um cortador ou um jigsaw da caixa podem ser

usados cortando o círculo.

• Una taglierina o un jigsaw della scatola può essere

utilizzato per il taglio del cerchio.

Add spacers to the plate in order to appropri-

ately position the camera, see specific camera.

• Agregue los espaciadores a la placa para colocar apropiada-

mente la cámara fotográfica, vea la cámara fotográfica

específica.

• Ajoutez les entretoises au plat afin de placer convenablement

l'appareil-photo, voyez l'appareil-photo spécifique.

• Fügen Sie Distanzscheiben der Platte hinzu, um die Kamera

passend in Position zu bringen, sehen Sie spezifische Kamera.

• Adicione espaçadores à placa a fim posicionar apropriada-

mente a câmera, veja a câmera específica.

• Aggiunga i distanziatori alla piastra per posizionare giusta-

mente la macchina fotografica, veda la macchina fotografica

specifica.

Place the housing in the tile and secure the

outer tabs.

• Coloque la cubierta en el azulejo y asegure las

lengüetas externas.

• Placez le logement dans la tuile et fixez les étiquettes

externes.

• Legen Sie das Gehäuse in die Fliese und sichern Sie

die äußeren Vorsprünge.

• Coloque a carcaça na telha e fixe as abas exteriores.

• Disponga l'alloggiamento nelle mattonelle ed assicuri

le linguette esterne.

Add the safety wire to the flex conduit or

continue to the next step.

• Agregue el alambre de seguridad al conducto de la

flexión o continúe al paso siguiente.

• Ajoutez le fil de sûreté au conduit de câble ou

continuez à la prochaine étape.

• Fügen Sie die Sicherheit Leitung dem Flexrohr hinzu

oder fahren Sie zum folgenden Schritt fort.

• Adicione o fio de segurança à canalização do cabo

flexível ou continue à etapa seguinte.

• Aggiunga il legare di sicurezza al condotto della

flessione o continui al punto seguente.

The alternate location to attach the safety

wire is on the housing secure tab.

• La localización alterna para unir el alambre de seguridad

está en la lengüeta segura de la cubierta.

• L'endroit alternatif pour attacher le fil de sûreté est sur

l'étiquette bloquée de logement.

• Die wechselnde Position, zum der Sicherheit Leitung

anzubringen ist auf dem sicheren Vorsprung des

Gehäuses.

• A posição alterna para unir o fio de segurança está na

aba segura da carcaça.

• La posizione alternata per fissare il legare di sicurezza è

sulla linguetta sicura dell'alloggiamento.

Connect the flex conduit to the housing.

• Conecte el conducto de la flexión con la

cubierta.

• Reliez le conduit de câble au logement.

• Schließen Sie das Flexrohr an das Gehäuse an.

• Conecte a canalização do cabo flexível à

carcaça.

• Colleghi il condotto della flessione

all'alloggiamento.

Heater/ Blower

Power

28 Watts

26 Watts

Wiring the dome can be completed by

referring to the diagram.

• Atar con alambre la bóveda puede ser terminada

refiriendo al diagrama.

• Le câblage du dôme peut être accompli en se

rapportant au diagramme.

• Das Verdrahten der Haube kann durchgeführt

werden, indem man auf das Diagramm sich bezieht.

• Wiring a abóbada pode ser terminado consultando

ao diagrama.

• Legare la cupola può essere completato riferendosi

allo schema.

AWG

,5 ,75 1,0 1,5 2,5 4 6

22 20 18 16 14 12 10

The beam angle may be adjusted on the

bottom of the unit.

• Éstos se recomiendan las distancias máximas para

24VAC con una gota del voltage del 10%.

• Ceux-ci sont recommandés des distances maximum

pour 24VAC avec une baisse de volatage de 10%.

• Diese werden maximale Abstände für 24VAC mit einem

das 10% volatage Tropfen empfohlen.

• Estes são recomendados distâncias máximas para

24VAC com uma gota do volatage de 10%.

• Questi sono suggeriti distanze massime per 24VAC con

una goccia di volatage di 10%.

These are recommended maximum distances

for 24VAC with a 10% voltage drop.

Green

Yellow

Orange

Red

Camera

Power

Accessory

Power

Camera = red & orange wires to terminal

Heater/Blower = yellow & green wires to terminal

• Cámara fotográfica = alambres rojos y anaranjados al

terminal Heater/Blower = alambres del amarillo y del verde

al terminal

• Appareil-photo = fils rouges et oranges à la borne

Heater/Blower = fils de jaune et de vert à la borne

• Kamera = rote u. orange Leitungen zum Anschluß

Heater/Blower = Gelb- u. Grünleitungen zum Anschluß

• Câmera = fios vermelhos & alaranjados ao terminal

Heater/Blower = fios do amarelo & do verde ao terminal

• Macchina fotografica = legare rossi & arancioni al terminale

Heater/Blower = legare di verde & di colore giallo al termi-

nale

The beam angle may be adjusted on the

bottom of the unit.

• Enganche el acollador de la bóveda a la cubierta

según lo demostrado.

• Accrochez la lanière du dôme au logement comme

montré.

• Spannen Sie die Abzuglinie von der Haube zum

Gehäuse an, wie gezeigt.

• Enganche o colhedor da abóbada à carcaça

como mostrada.

• Agganci la cordicella dalla cupola all'alloggiamento

come indicato.

Hook the lanyard from the dome to the

housing as shown.

The beam angle may be adjusted on the bottom of the unit.

• Instale la cámara fotográfica en la cubierta y termine los usos del

cableado. Vea las especificaciones de la cámara fotográfica.

• Installez l'appareil-photo dans le logement et accomplissez les

applications de câblage. Voir les caractéristiques d'appareil-

photo.

• Bringen Sie die Kamera in das Gehäuse an und führen Sie Verdrah-

tung Anwendungen durch. Sehen Sie Kameraspezifikationen.

• Instale a câmera na carcaça e termine aplicações da fiação.

Veja especificações da câmera.

• Installi la macchina fotografica nell'alloggiamento e completi le

applicazioni dei collegamenti. Veda le specifiche della macchina

fotografica.

Install the camera in the housing and complete

wiring applications. See camera specifications.

beam angle may be adjusted on the bttom

o the unit.

• Asegure la bóveda con los tornillos ya en la bóveda.

• Fixez le dôme avec des vis déjà dans le dôme.

• Sichern Sie die Haube mit Schrauben bereits in der

Haube.

• Fixe a abóbada com parafusos já na abóbada.

• Fissi la cupola con le viti già nella cupola.

Secure the dome with screws already

in the dome.

• Los tornillos de la seguridad proporcionados se pueden

también utilizar para unir la bóveda.

• Les vis de sécurité fournies peuvent également être

utilisées pour attacher le dôme.

• Die bereitgestellten Sicherheit Schrauben können auch

benutzt werden, um die Haube anzubringen.

• Os parafusos da segurança fornecidos podem

também ser usados unir a abóbada.

• Le viti di sicurezza fornite possono anche essere

utilizzate per fissare la cupola.

The security screws provided can also be used

to attach the dome.

Install the camera to the mounting plate with (2) #10 screws and lock washers provided. Place (3)

#8x3/8” screws on the spacers and align the mounting slots. Slide on plate and camera then secure.

• Instale la cámara fotográfica a la placa de montaje con (2) los tornillos #10 y las arandelas de cerradura proporcionadas. Coloque los

tornillos de (3) del # 8x3/8"en los espaciadores y alinee las ranuras de montaje. Resbale en la placa y la cámara fotográfica entonces

seguras.

• Installez l'appareil-photo sur le plat de support avec (2) les vis #10 et les rondelles de freinage fournies. Placez les vis de (3) # de 8x3/8"

sur les entretoises et alignez les fentes de support. Glissez du plat et de l'appareil-photo puis bloqués.

• Bringen Sie die Kamera zur Montageplatte mit (2) den bereitgestellten Schrauben #10 und Federringen an. Setzen Sie (3) # 8x3/8"die

Schrauben auf die Distanzscheiben und richten Sie die Befestigungsschlitze aus. Schieben Sie auf die sichere Platte und Kamera dann.

• Instale a câmera à placa de montagem com (2) os parafusos #10 e as arruelas de fechamento fornecidas. Coloque os parafusos de

(3) # de 8x3/8"nos espaçadores e alinhe os entalhes de montagem. Deslize na placa e na câmera então seguras.

• Installi la macchina fotografica al giunto di supporto con (2) le viti #10 e le ranelle di bloccaggio fornite. Disponga le viti di 8x3/8"# di (3)

sui distanziatori ed allinei le scanalature di montaggio. Faccia scorrere sulla piastra e sulla macchina fotografica allora sicure.

2539 Mounting Plate

Mounting

Hole

Mounting

Hole

Axis 213

(26

) 1"

(52

) 2"

(13

) ½"

Captive

Screw

(3) #8x3/8”

3026 Mounting

Plate

Mounting

Hole

Mounting

Hole

Mounting Hole

Axis 214

(52

) 2"

Captive

Screw

(3) #8 x 3/8”

Install the camera to the mounting plate using (3) 3mm x 12mm bolts and lock washers. Place (3) #8x3/8”

screws on the spacers and line up the mounting slots. Slide plate in and secure.

• Instale la cámara fotográfica a la placa de montaje usando (3) los pernos de 3m m x de 12m m y las arandelas de cerradura.

Coloque los tornillos de (3) del # 8x3/8"en los espaciadores y alinee las ranuras de montaje. Resbale la placa adentro y

asegúrela.

• Installez l'appareil-photo sur le plat de support en utilisant (3) des boulons de 3mm x de 12mm et des rondelles de freinage.

Placez les vis de (3) # de 8x3/8"sur les entretoises et alignez les fentes de support. Glissez le plat dedans et le fixez.

• Bringen Sie die Kamera zur Montageplatte mit (3) 3mm x 12mm den Schraubbolzen und den Federringen an. Setzen Sie (3) #

8x3/8"die Schrauben auf die Distanzscheiben und richten Sie die Befestigungsschlitze aus. Schieben Sie Platte innen und sichern

Sie.

• Instale a câmera à placa de montagem usando (3) os parafusos de 3mm x de 12mm e as arruelas de fechamento. Coloque os

parafusos de (3) # de 8x3/8"nos espaçadores e alinhe-os acima dos entalhes de montagem. Deslize a placa dentro e fixe-a.

• Installi la macchina fotografica al giunto di supporto usando (3) i bulloni di 12mm x di 3mm e le ranelle di bloccaggio. Disponga

le viti di 8x3/8"# di (3) sui distanziatori ed allinei le scanalature di montaggio. Faccia scorrere la piastra dentro e fissi.

Install the camera to the mounting plate with (4) #8 screws and lock washers provided. Place (3)

#8x3/8” screws on the spacers and align the mounting slots. Slide on plate and camera then secure.

• Instale la cámara fotográfica a la placa de montaje con (4) los tornillos #8 y las arandelas de cerradura proporcionadas. Coloque los

tornillos de (3) del # 8x3/8"en los espaciadores y alinee las ranuras de montaje. Resbale en la placa y la cámara fotográfica entonces

seguras.

• Installez l'appareil-photo sur le plat de support avec (4) les vis #8 et les rondelles de freinage fournies. Placez les vis de (3) # de 8x3/8"

sur les entretoises et alignez les fentes de support. Glissez du plat et de l'appareil-photo puis bloqués.

• Bringen Sie die Kamera zur Montageplatte mit (4) den bereitgestellten Schrauben #8 und Federringen an. Setzen Sie (3) # 8x3/8"die

Schrauben auf die Distanzscheiben und richten Sie die Befestigungsschlitze aus. Schieben Sie auf die sichere Platte und Kamera dann.

• Instale a câmera à placa de montagem com (4) os parafusos #8 e as arruelas de fechamento fornecidas. Coloque os parafusos de

(3) # de 8x3/8"nos espaçadores e alinhe os entalhes de montagem. Deslize na placa e na câmera então seguras.

• Installi la macchina fotografica al giunto di supporto con (4) le viti #8 e le ranelle di bloccaggio fornite. Disponga le viti di 8x3/8"# di (3)

sui distanziatori ed allinei le scanalature di montaggio. Faccia scorrere sulla piastra e sulla macchina fotografica allora sicure.

Axis 215

(26

) 1"

(52

) 2"

Captive

Screw

(3) #8x3/8”

(26

) 1"

MOUNTING HOLE

AXIS215-VL3026

MOUNTING HOLE

Axis 231D/232D

Use the (3) keyhole slots indicated above.

• Utilice (3) las ranuras del ojo de la cerradura indicadas

arriba.

• Employez (3) les fentes de trou de la serrure indiquées

ci-dessus.

• Benutzen Sie die (3) Schlüssellochschlitze, die oben

angezeigt werden.

• Use (3) os entalhes do buraco da fechadura indicados

acima.

• Usi (3) le scanalature del buco della serratura indicate

sopra.

Mounting

Hole

Mounting

Hole

Mounting Hole

Tab

Loosen

Screw

AXIS 231-232D

Loosen the screw to the right of the tab by

approximately (5) turns.

• Afloje el tornillo a la derecha de la lengüeta aproxi-

madamente (5) vueltas.

• Desserrez la vis à la droite de l'étiquette approxima-

tivement (5) aux tours.

• Lösen Sie die Schraube auf der rechten Seite des

Vorsprunges durch ungefähr (5) Umdrehungen.

• Afrouxe o parafuso à direita da aba aproximada-

mente (5) por voltas.

• Allenti la vite alla destra della linguetta circa (5) dalle

girate.

Captive

Screw

(3) #8 x 3/8”

Locking Screw

Locking

Pins

Keyhole

Slot (3)

(13

) ½"

Position locking pins and locking screw over slots and turn clockwise; secure the screw. Place (3)

#8x3/8” screws on the spacers and line up mounting slots. Slide on plate and camera then secure.

• Coloque los pernos de fijación y el tornillo de fijación sobre ranuras y dé vuelta a la derecha; asegure el tornillo. Coloque los tornillos de

(3) del # 8x3/8"en los espaciadores y las ranuras de montaje de la formación. Resbale en la placa y la cámara fotográfica y asegure.

• Placez les chevilles de verrouillage et la vis de blocage au-dessus des fentes et tournez dans le sens des aiguilles d'une montre ; fixez la

vis. Placez les vis de (3) # de 8x3/8"sur les entretoises et les fentes de support de ligne. Glissez du plat et de l'appareil-photo et fixez.

• Bringen Sie Sicherungsstifte und Sicherungsschraube über Schlitzen in Position und drehen Sie nach rechts; sichern Sie die Schraube.

Setzen Sie (3) # 8x3/8"die Schrauben auf die Distanzscheiben und die Anordnungbefestigungsschlitze. Schieben Sie auf Platte und

Kamera und sichern Sie.

• Posicione os pinos travando e o parafuso travando sobre entalhes e gire-os no sentido horário; fixe o parafuso. Coloque os parafusos

de (3) # de 8x3/8"nos espaçadores e alinhe-os acima dos entalhes de montagem. Deslize na placa e na câmera e fixe.

• Posizioni i perni di bloccaggio e la vite di bloccaggio sopra le scanalature e giri in senso orario; fissi la vite. Disponga le viti di 8x3/8"# di

(3) sui distanziatori e sulle scanalature di montaggio dell'allineamento. Faccia scorrere sulla piastra e sulla macchina fotografica e fissi.

3mm

Screw

Power

Board

Connection

Module

This is what the typical path of illumination will look like with the setting at 30 degrees.

• Quite a tablero de energía situado dentro de la cubierta. Una el módulo de la conexión según lo demostrado. Una

a esta asamblea a la cubierta usando (1) "arandela del tornillo 6-32x3/8 y de la estrella.

• Enlevez carte d'alimentation situé à l'intérieur du logement. Attachez le module de raccordement comme montré.

Attachez cette assemblée au logement en utilisant (1) la "vis 6-32x3/8 et tenez le premier rôle la rondelle.

• Entfernen Sie das Energie Brett, das innerhalb des Gehäuses befunden wird. Bringen Sie das Anschlußmodul an, wie

gezeigt. Bringen Sie diese Versammlung zum Gehäuse mit (1) "Schraube 6-32x3/8 und Sternunterlegscheibe an.

• Remova a placa de poder situada dentro da carcaça. Una o módulo da conexão como mostrado. Una este

conjunto à carcaça usando (1) do "arruela parafuso 6-32x3/8 e da estrela.

• Rimuova il bordo di alimentazione situato all'interno dell'alloggiamento. Fissi il modulo del collegamento come

indicato. Fissi questo complessivo all'alloggiamento usando (1) "rondella della vite 6-32x3/8 e della stella.

Remove the power board located inside the housing. Attach the connection module as shown.

Attach this assembly to the housing using (1) 6-32x3/8” screw and star washer.

This is what the typical path of illumination will look like with the setting at 30 degrees.

• Termine el cableado a la cámara fotográfica. Una el montaje de la cámara fotográfica a la cubierta resbalando

(3) las ranuras abiertas del tornillo sobre los tornillos en la cubierta; apriete los sujetadores en el soporte.

• Accomplissez le câblage à l'appareil-photo. Attachez l'appareil-photo au logement en glissant (3) les fentes

ouvertes de vis au-dessus des vis dans le logement ; serrez les attaches sur la parenthèse.

• Führen Sie die Verdrahtung zur Kamera durch. Bringen Sie die Kamera zum Gehäuse an, indem Sie die (3) geöffne-

ten Schraube Schlitze über den Schrauben im Gehäuse schieben; ziehen Sie die Befestiger am Haltewinkel fest.

• Termine a fiação à câmera. Una o conjunto da câmera à carcaça deslizando (3) os entalhes abertos do parafuso

sobre os parafusos na carcaça; aperte os prendedores no suporte.

• Completi i collegamenti alla macchina fotografica. Fissi il complessivo della macchina fotografica all'alloggiamento

facendo scorrere (3) le scanalature aperte della vite sopra le viti nell'alloggiamento; stringa i fermi sulla staffa.

CONTROL

RJ45 Ethernet Connector

ALARMS

1 Alarm 1 Blue

2 Alarm 2 Violet

3 Alarm 3 Gray

4 Common White

POWER

1 Camera Power (24VAC) Red

2 Camera Power (24VAC) Orange

Captive

Screw

Open Screw

Slots

Cable

Ties

Complete the wiring to camera. Attach the camera assembly to the housing by sliding the (3)

open screw slots over the screws in the housing; tighten the fasteners on the bracket.

Axis 233D

Use the holes indicated above to mount

the camera.

• Utilice los agujeros indicados arriba para montar la

cámara fotográfica.

• Employez les trous indiqués ci-dessus pour monter

l'appareil-photo.

• Benutzen Sie die Bohrungen, die oben angezeigt

werden, um die Kamera anzubringen.

• Use os furos indicados acima para montar a

câmera.

• Usi i fori indicati sopra per montare la macchina

fotografica.

Mounting Hole

Machine

Screws

Disconnect the orange, red, and black wires. Remove the

power board in the housing by loosening screws on the

terminal block and the (4) machine screws.

• Desconecte los alambres anaranjados, rojos, y negros. Quite a tablero de

energía en la cubierta aflojando los tornillos en el bloque de terminales y (4)

los tornillos de la máquina.

• Débranchez les fils oranges, rouges, et noirs. Enlevez carte d'alimentation

dans le logement en desserrant des vis sur le TB et (4) les vis de machine.

• Trennen Sie die orange, roten und schwarzen Leitungen. Entfernen Sie das

Energie Brett im Gehäuse, indem Sie Schrauben am Klemmenblock und an

den (4) Maschine Schrauben lösen.

• Desconecte os fios alaranjados, vermelhos, e pretos. Remova a placa de

poder na carcaça afrouxando os parafusos no bloco terminal e (4) nos

parafusos da máquina.

• Stacchi i legare arancioni, rossi e neri. Rimuova il bordo di alimentazione

nell'alloggiamento allentando le viti sul blocchetto terminali e (4) sulle viti

della macchina.

Power

Board

Now remove the mounting bracket and attach (4) 1/2” spacers (located in the packet that came

with the housing) to the base bracket.

• Ahora quite el soporte de montaje y una (4) los espaciadores del 1/2"(situados en el paquete que vino con la cubierta)

al soporte bajo.

• Maintenant enlevez le support et attachez (4) les entretoises de 1/2"(situées dans le paquet qui est venu avec le

logement) à la parenthèse basse.

• Jetzt entfernen Sie die Schienenplatte und bringen Sie (4) die 1/2"Distanzscheiben (gelegen im Paket, das mit dem

Gehäuse kam), zum niedrigen Haltewinkel an.

• Agora remova o suporte de montagem e una (4) os espaçadores de 1/2"(situados no pacote que veio com a

carcaça) ao suporte baixo.

• Ora rimuova il supporto di attacco e fissi (4) i distanziatori di 1/2"(situati nel pacchetto che è venuto con

l'alloggiamento) alla staffa bassa.

Mounting

Bracket

½"

Quick Release

Plate

Base Bracket

Camera

Bracket

Additional

Spacers

Keyhole

Slots

This is what the typical path of illumination will look like with the setting at 30 degrees.

• Monte el soporte de la cámara fotográfica del eje 233D y la placa rápida del lanzamiento usando los espaciadores

adicionales del paquete del hardware.

• Montez la parenthèse d'appareil-photo de l'axe 233D et le plat rapide de dégagement en utilisant les entretoises

additionnelles du paquet de matériel.

• Bringen Sie den Mittellinie 233D Kamerahaltewinkel und schnelle die Freigabeplatte mit den zusätzlichen Distanzs-

cheiben vom Kleinteilpaket an.

• Monte o suporte da câmera da linha central 233D e a placa rápida da liberação usando os espaçadores adicio-

nais do pacote da ferragem.

• Monti la staffa della macchina fotografica di asse 233D e la piastra rapida del rilascio usando i distanziatori supple-

mentari dal pacchetto dei fissaggi.

Mount the Axis 233D camera bracket and quick release plate using the additional spacers from

the hardware packet.

This is what the typical path of illumination will look like with the setting at 30 degrees.

• Coloque la placa rápida del lanzamiento sobre el fondo de la cámara fotográfica. Alinee los tornillos de fijación de la cámara fotográfica y las

ranuras del ojo de la cerradura. Resbale la cámara fotográfica dentro de las ranuras del ojo de la cerradura hasta que los botones de fijación

golpean el extremo, y apriete el tornillo de fijación.

• Placez le plat rapide de dégagement sur le fond de l'appareil-photo. Alignez les vis de blocage d'appareil-photo et les fentes de trou de la

serrure. Glissez l'appareil-photo dans les fentes de trou de la serrure jusqu'à ce que les boutons de fermeture frappent l'extrémité, et serrez la vis de

blocage.

• Setzen Sie schnelle Freigabeplatte auf der Unterseite der Kamera. Richten Sie die Sicherungsschrauben der Kamera und die Schlüssellochschlitze

aus. Schieben Sie Kamera in die Schlüssellochschlitze, bis die verriegelntasten das Ende schlagen, und ziehen Sie die Sicherungsschraube fest.

• Coloque a placa rápida da liberação no fundo da câmera. Alinhe os parafusos travando da câmera e os entalhes do buraco da fechadura.

Deslize a câmera nos entalhes do buraco da fechadura até que as teclas travando batam a extremidade, e aperte o parafuso travando.

• Disponga la piastra rapida del rilascio sulla parte inferiore della macchina fotografica. Allinei le viti di bloccaggio della macchina fotografica e le

scanalature del buco della serratura. Faccia scorrere la macchina fotografica nelle scanalature del buco della serratura fino a che i tasti di

bloccaggio non colpiscano l'estremità e stringa la vite di bloccaggio.

Place quick release plate onto the bottom of the camera. Align the camera locking screws and the keyhole

slots. Slide camera into the keyhole slots until the locking buttons hit the end, and tighten the locking screw.

Keyhole Slots

Thumb Screw

Locking Screw

2539 Mounting Plate

Mounting

Hole

Mounting

Hole

Canon VB-C10R

Captive

Screw

(26

) 1"

(52

) 2"

(13

) ½"

Mount the camera to the 2539 plate using the provided hardware. Place (3) 8 x 32 x 3/8 Phillips

head screws on the top of the spacer as shown above. Slide plate in and secure.

• Monte la cámara fotográfica a la placa 2539 usando el hardware proporcionado. Coloque (3) 8 x 32 x 3/8 de los

tornillos principales Phillips en la tapa del espaciador según lo demostrado arriba. Resbale la placa adentro y

asegúrela.

• Montez l'appareil-photo au plat 2539 à l'aide du matériel fourni. Placez (3) 8 x 32 x 3/8 de vis principales Phillips sur le

dessus de l'entretoise comme montré ci-dessus. Glissez le plat dedans et le fixez.

• Bringen Sie die Kamera zur Platte 2539 mit den zur Verfügung gestellten Kleinteilen an. Setzen Sie (3) 8 x 32 x 3/8 Kreuz-

kopfhauptschrauben auf die Oberseite der Distanzscheibe, wie oben gezeigt. Schieben Sie Platte innen und sichern Sie.

• Monte a câmera à placa 2539 usando a ferragem fornecida. Coloque (3) 8 x 32 x 3/8 dos parafusos principais Phillips

no alto do espaçador como mostrado acima. Deslize a placa dentro e fixe-a.

• Monti la macchina fotografica alla piastra 2539 per mezzo dei fissaggi forniti. Disponga (3) 8 x 32 x 3/8 delle viti cape

"phillips" sulla parte superiore del distanziatore come indicato sopra. Faccia scorrere la piastra dentro e fissi.

2539 Mounting Plate

Mounting

Hole

Mounting

Hole

Canon VB-C50IR

Captive

Screw

(26

) 1"

(52

) 2"

(13

) ½"

Mount the camera to the 2539 plate using the provided hardware. Place (3) 8 x 32 x 3/8

Phillips head screws on the top of the spacer as shown above. Slide plate in and secure.