Regulatory Model: 300-000-239
40U-P Cabinet
Unpacking and Setup Guide
Rev. Rev 02
July 2020
This Unpacking and Setup Guide contains information about the 40U-P cabinet. Topics include:
• Before you start .........................................................................................................................................................................................................2
• Tools required..............................................................................................................................................................................................................2
• Hardware acclimation.................................................................................................................................................................................................2
• Steps to unpack and setup cabinet..........................................................................................................................................................................3
• Remove the ramp and shipping material from the cabinet................................................................................................................................... 3
• Remove the cabinet shipping brackets....................................................................................................................................................................5
• Attach the unloading ramp........................................................................................................................................................................................ 6
• Roll the cabinet down the ramp................................................................................................................................................................................7
• Position and level the cabinet................................................................................................................................................................................... 8
• Power requirements...................................................................................................................................................................................................8
• Attach (optional) brackets........................................................................................................................................................................................11
• Install the lower trim strip.........................................................................................................................................................................................12
• Ground the cabinet................................................................................................................................................................................................... 13
• Repackaging shipping material (2-piece ramp kits only)......................................................................................................................................14
• If you need help......................................................................................................................................................................................................... 15
Before you start
This section contains important information you should read prior to unpacking and setting up the 40U-P cabinet.
CAUTION: Some products are designed for installation by trained service personnel only. Attempts by unqualified personnel to
set up and start certain products may result in system damage and may void product warranties. Contact your representative
for detailed warranty, installation, and initialization policies.
Please dispose of shipping material responsibly, and recycle wherever and whenever possible. Cabinet packaging that includes a collapsible
downloading ramp can be re-packaged and returned, as described in Repackaging shipping material (2-piece ramp kits only).
CL5427
NOTE: The illustrations in this guide are examples only. Depending on what you ordered, your configuration may look somewhat
different from what is shown here.
Tools required
• 9/16-in. (14-mm) socket wrench
• Adjustable wrench
• Flat screwdriver
• Phillips screwdriver
Hardware acclimation
Systems and components must acclimate to the operating environment before power is applied to them. Once unpackaged, the system
must reside in the operating environment for up to 16 hours to thermally stabilize and prevent condensation.
If the last 24 hours of the TRANSIT/STORAGE environment
was:
…and the OPERATING
environment is:
…then let the system or
component acclimate in the
new environment this many
hours:
Temperature Relative Humidity Temperature Acclimation Time
Nominal
68–72°F (20–22°C)
Nominal 40–55% RH Nominal
68–72°F (20–22°C) 40–55%
RH
1 hour or less
Cold <68°F (20°C) Dry <30% RH <86°F (30°C) 4 hours
2
If the last 24 hours of the TRANSIT/STORAGE environment
was:
…and the OPERATING
environment is:
…then let the system or
component acclimate in the
new environment this many
hours:
Damp >30% RH
Hot >72°F (22°C) Dry <30% RH
Humid 30–45% RH
Hot >72°F (22°C) Humid 45–60% RH <86°F (30°C) 8 hours
Hot >72°F (22°C) Humid >60% RH <86°F (30°C) 16 hours
Unknown
IMPORTANT:
• If there are signs of condensation after the recommended acclimation time has passed, allow an additional eight (8) hours to stabilize.
• System components must not experience changes in temperature and humidity that are likely to cause condensation to form on or in
that system or component. Do not exceed the shipping and storage temperature gradient of 45°F/hr (25°C/hr).
• To facilitate environmental stabilization, open both front and rear cabinet doors.
Steps to unpack and setup cabinet
The steps to unpack, setup and repackage the shipping material are listed in the following table:
Step
Task
1 Remove the ramp and shipping material from the cabinet on page 3
2 Remove the cabinet shipping brackets on page 5
3 #unique_10
4 Roll the cabinet down the ramp on page 7
5 Position and level the cabinet on page 8
6 Attach AC power input cords
7 Attach (optional) brackets on page 11
8 Install the lower trim strip on page 12
9 Ground the cabinet on page 13
10 Repackaging shipping material (2-piece ramp kits only) on page 14
Remove the ramp and shipping material from the
cabinet
Steps
1. Remove any boxes and other material from the cabinet sides.
3
CL4691
2. Do not pull a ramp down from the top. To release the ramp from the pallet, grasp the ramp, pull it straight back toward you, then pull it
straight up to free it from the screws.
4
Accessory Kit
EMC3552
Rotated 90
Bracket
Bracket
Screws
Rear
3. Remove the plastic covering from the cabinet.
Remove the cabinet shipping brackets
Steps
1. At the rear of the cabinet, remove the rear shipping bracket, by removing the bolts that go through the bracket to the cabinet and into
the pallet.
2. At the front of the cabinet, remove the bottom cabinet bezel, if necessary. Pull the bezel straight out to remove it.
3. Remove the bolts that attach the cabinet to the front shipping bracket. Your can leave the front bracket attached to the shipping
pallet.
NOTE:
Save the bolts. You may need them later to install optional stabilizer brackets.
5
Attach the unloading ramp
Steps
1. Insert the ramp brackets into the pallet notches in the rear of the pallet.
2. If your shipment includes a two-piece ramp, attach part A to the pallet and part B to part A.
6
CL4692
Roll the cabinet down the ramp
About this task
NOTE:
Make certain the leveling feet are secured in the UP position before moving the cabinet. Secured feet allow the cabinet
to roll off the ramp and into position. If you need to adjust the leveling feet, use the 6mm hex key (top access) or an adjustable
wrench (bottom access) to turn the feet counter-clockwise. This raises them to the UP position.
EMC2845
Leveling
Feet
Rear
Rails
WARNING:
The cabinet is heavy. Make certain you have sufficient help and secure footing before rolling the cabinet onto the ramp.
ATTENTION! L'armoire est lourde. Assurez-vous d'obtenir l'aide d'une personne et d'avoir un point d'appui sûr avant d'installer
l'armoire sur la rampe.
ACHTUNG! Das Gestell ist schwer. Versichern Sie sich, dass Sie genügend Hilfe haben und dass das Fundament gesichert ist,
bevor Sie das Gestell auf die Rampe rollen.
7
ATTENZIONE! Poiché il cabinet è molto pesante assicurarsi di essere in un numero sufficiente di persone e di avere un appoggio
sicuro prima di spingerlo sullo scivolo.
ADVERTENCIA! El bastidor es pesado. Asegúrese de contar con ayuda suficiente y de tener un apoyo seguro antes de colocar
el bastidor en la rampa.
WARNING: Balance the cabinet from the sides; do not grasp the plastic bezels or other components on the front of the cabinet.
DO NOT STAND IN FRONT OF THE CABINET
EMC2846
Position and level the cabinet
About this task
EMC2847
1 3/8-in.
Power requirements
Depending on the cabinet configuration and input ac power source, single or three-phase, the cabinet requires two to 12 independent
power sources. To determine your site requirements, use the published technical specifications and device rating labels. This will help
provide the current draw of the devices in each rack. The total current draw for each rack can then be calculated. For Dell EMC products,
visit the "Dell EMC Power Calculator" on the web at http://powercalculator.dell.com.
Table 1. Single-phase power connection requirements
Specification North American
3 wire connection (2 L and 1 G)
a
International and Australian
3 wire connection (1 L, 1 N, and 1 G)
Input nominal voltage 200 - 240 V ac +/- 10% L - L nom 220 - 240 V ac +/- 10% L - L nom
8
Table 1. Single-phase power connection requirements (continued)
Specification North American
3 wire connection (2 L and 1 G)
a
International and Australian
3 wire connection (1 L, 1 N, and 1 G)
Frequency 50 - 60 Hz 50 - 60 Hz
Circuit breakers 30 A 32 A
Power zones Two Two
Power requirements at site (minimum to
maximum)
• One to six 30 A, single-phase drops per zone
• Each rack requires a minimum of two drops to a maximum of 12 drops. This will be
determined by the system configuration and the power needs for that configuration.
a.
L = line phase, N = neutral, G = ground
Table 2. Single-phase AC power input connector options
Single-phase rack connector options Customer AC source interface receptacle Site
NEMA L6-30P
NEMA L6-30R
North America and Japan
Russellstoll 3750DP
Russellstoll 9C33U0
North America and Japan
IEC-309 332P6
IEC-309 332C6
International
CLIPSAL 56PA332
CLIPSAL 56CSC332
Australia
Table 3. Three-phase AC power connection requirements
Specification North American (Delta)
4 wire connection (3 L and 1 G)
a
International and Australian (Wye)
5 wire connection (3 L, 1 N, and 1 G)
Input nominal voltage 200 - 240 V ac +/- 10% L - L nom 220 - 240 V ac +/- 10% L - N nom
Frequency 50 - 60 Hz 50 - 60 Hz
Circuit breakers 50 A 32 A
Power zones Two Two
Power requirements at site (minimum to
maximum)
North America (Delta):
• One to two 50 A, three-phase drops per zone
• Each rack requires a minimum of two drops to a maximum of four drops. This will be
determined by the system configuration and the power needs for that configuration.
International (Wye):
9
Table 3. Three-phase AC power connection requirements (continued)
Specification North American (Delta)
4 wire connection (3 L and 1 G)
a
International and Australian (Wye)
5 wire connection (3 L, 1 N, and 1 G)
• One 32 A, three-phase drop per zone
• Each rack requires a minimum of two drops to a maximum of four drops. This will be
determined by the system configuration and the power needs for that configuration.
NOTE: The interface connector options for the Delta and Wye three-phase PDUs
are listed in and
a.
L = line phase, N = neutral, G = ground
Table 4. Three-phase Delta-type AC power input connector options
Three-phase Delta rack connector options Customer AC source interface receptacle Site
Russellstoll 9P54U2
Russellstoll 9C54U2
North America and International
Hubbell CS-8365C
Hubbell CS-8364C
North America
Table 5. Three-phase Wye-type AC power input connector options
Three-phase Wye rack connector options Customer AC source interface receptacle Site
GARO P432-6
GARO S432-6
International
Hubbell L22-30P Hubbell L22-30R North America
Fly Lead Customer Receptacle International
10
Attach (optional) brackets
We strongly recommend that you secure your cabinet to the floor with stabilizing brackets. Make sure the cabinet is in its final location
before attaching the brackets, then use the supplied bolts and mounting holes to attach them to the cabinet and floor
About this task
CL4830
(3)
(3)
Figure 1. Anti-tip bracket (installed on the front of cabinet)
CL4832
(3)
(3)
Figure 2. Anti-move bracket (installed on the front and back of cabinet)
11
CL4833
(3)
(3)
(3)
(3)
Figure 3. Seismic bracket (installed on the front, back, and sides of the cabinet)
Install the lower trim strip
This procedure describes how to install the lower trim strip.
About this task
NOTE: If the cabinet is shipped with a front door, there is no need to install the lower front bezel/trim strip.
Steps
1. Wipe down the lower cabinet with alcohol wipes.
2. On the underside of the lower trim strip, remove the double-sided tape from the velcro fasteners.
Figure 4. Placement of velcro fasteners on lower trim strip
3. Align the lower trim strip with the lower cabinet and firmly press the bezel onto the cabinet until it adheres to the cabinet.
12
Figure 5. Attaching lower trim strip
Ground the cabinet
Equipment correctly installed within the cabinet is grounded through the AC power cables and connectors. In general, supplemental
grounding is not required.
About this task
If your site requires external grounding (for example, to a common grounding network beneath the site floor), you can use the grounding
lugs provided on each of the cabinet’s lower power distribution panels (PDP).
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
CL5003
046-003-350
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
046-003-350
Ground lug
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
13
Repackaging shipping material (2-piece ramp kits
only)
About this task
Follow these steps to repackage the shipping material:
Steps
1. Lay each of the outer sleeves flat, then fold it lengthwise before collapsing the three sections, as shown:
3
CL4690
1
2
2. Stack the shipping brackets on the pallet, as shown:
CL4697
3
21
3. Place ramp section B upside-down on the pallet, then stack section A, right-side up.
4. Stack the two folded outer sleeves above the ramp sections.
5. Apply the two collar sections to either side of the pallet; hold them in place with the package hood.
14
6. Band the unit with shipping straps as shown:
CL4751
7. Use the following information to determine how to return the repackaged shipping material:
• If the carrier unpacked the cabinet, the carrier handles the return shipment to the packaging supplier.
• If the cabinet was unpacked after delivery, refer to the contact number attached to the pamphlet for repacking. This contact is the
carrier network for the initial shipment and they will follow the same process as for the initial shipments.
If you need help
For questions about technical support and service, contact you service provider.
For questions about upgrades, contact your sales office.
More information about this and other products is available on the online support website.
15
Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make better use of your product.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
© 2018 - 2020 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other
trademarks may be trademarks of their respective owners.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
Dell EMC PowerStore Rack Guida Rapida
- Tipo
- Guida Rapida
- Questo manuale è adatto anche per
in altre lingue
Altri documenti
-
Eaton BladeUPS none Manuale utente
-
Juniper JCS1200 Manuale utente
-
Juniper MX204 Manuale utente
-
-
-
-
-
-
-