ETC Unison Paradigm P-TS7 Guida d'installazione

ETC
Marca
ETC
Modello
Unison Paradigm P-TS7
Tipo
Guida d'installazione
ETC
®
Installation Guide
Unison Paradigm
®
P-TS7 Rack Panel
P-TS7 Rack Panel Page 1 of 4 Electronic Theatre Controls, Inc.
Corporate Headquarters
3031 Pleasant View Road, P.O. Box 620979, Middleton, Wisconsin 53562-0979 USA
Tel +608 831 4116
Fax +608 836 1736
London, UK
Unit 26-28, Victoria Industrial Estate, Victoria Road, London W3 6UU, UK
Tel +44 (0)20 8896 1000
Fax +44 (0)20 8896 2000
Rome, IT
Via Pieve Torina, 48, 00156 Rome, Italy
Tel +39 (06) 32 111 683
Fax +44 (0)20 8896 2000
Holzkirchen, DE
Ohmstrasse 3, 83607 Holzkirchen, Germany
Tel +49 (80 24) 47 00-0
Fax +49 (80 24) 47 00-3 00
Hong Kong
Rm 1801, 18/F, Tower 1 Phase 1, Enterprise Square, 9 Sheung Yuet Road, Kowloon Bay, Kowloon, Hong Kong
Tel +852 2799 1220
Fax +852 2799 9325
Service:
(Americas) service@etcconnect.com
(UK) service@etceurope.com
(DE) techserv-hoki@etcconnect.com
(Asia) [email protected]
Web:
www.etcconnect.com
Copyright © 2015 ETC. All Rights Reserved.
Product information and specifications subject to change.
7184M2190
Rev A
Released 2015-01
ETC intends this document to be provided in its entirety.
Overview
The Unison Paradigm
®
P-TS7 Touchscreen can be installed in an equipment rack using a rack panel,
which is shipped separately. It is powered by either LinkPower with auxiliary power or by PoE (Power
over Ethernet 802.3af).
• Echelon
®
LinkPower
®
(LinkConnect) control network using Belden 8471 (or approved equal) and
24 Vdc Auxiliary power (two 16 AWG 1.5mm
2
) wires.
• PoE (Power Over Ethernet 802.3af) using Category 5 cable (or approved equal).
Control wiring should only be installed and terminated by a qualified technician and should follow
standard wiring installation practices. Leave approximately 10 inches (254mm) of wiring in the backbox
for connection and to allow slack for future service needs. For more information about terminating CAT5
cable, refer to the ETC Ethernet Cat5 Termination Kit Setup Guide.
Install Collar in Rack Panel
Installation should follow local codes and standard practices. Ensure that all wiring is installed correctly.
The touchscreen is supplied with an installation kit which includes the necessary hardware and
electrical supplies.
Step 1: Slide the collar into the rack panel.
Step 2: Install and tighten four M4 x 20mm collar mount screws through the collar and into the
rack panel.
Paradigm Touchscreen Model
Model Description
P-TS7-RM Paradigm Touchscreen Rack Panel
Note:
It is important to orient the rack panel with the cutout on the right side to provide better
cable access between the touchscreen and the Termination PCB.
In addition, the collar should be installed with the stamped arrow (
) pointing up.
Mounting
Pin
Cutout on
right side
ETC Installation Guide
P-TS7 Rack Panel
P-TS7 Rack Panel Page 2 of 4 Electronic Theatre Controls, Inc.
Install the Termination PCB
The printed circuit board (PCB) assembly is designed to accommodate either Ethernet or LON
connections. Prior to installing the PCB, terminate all necessary wiring. The PCB is installed on the
back (inside) of the rack panel.
The PCB consists of three parts:
• PCB with female RJ11, LinkPower connector, 24 Vdc (Aux) connector, and ground spade
• RJ45 with punch down wire termination
• Mounting bracket and screws
Installing the Termination PCB on the Rack Panel
Step 1: Position the PCB on the four standoffs on the back of the rack panel and secure with two
M3x10mm pan head screws on the RJ11 side of the PCB only.
Step 2: Place the bracket and RJ45 assembly (if used) on top of the PCB. Secure the PCB to the
backbox through the remaining two holes in the PCB with M3x10mm pan head screws.
Step 3: A ground connection is required for all touchscreen assemblies. Using one three position
WAGO connector, connect the (typically green and yellow) installed wire(s) with the
ground wire pigtail (with attached spade), provided in the installation kit, and the ground
wire attached to the rack panel.
Note:
The termination PCB can be installed in any orientation to accommodate wiring.
Orienting the PCB with the ground and LinkPower connections toward the top of the
rack (as illustrated) will simplify installation.
CAUTION:
Only one network type (LON or Ethernet) may be connected to the touchscreen at a
time. Do not connect both Auxiliary power and PoE.
ETC requires that all backboxes and touchscreens are grounded in accordance with
local electrical codes.
The RJ11 connection must be used to provide a ground connection from the backbox
to the touchscreen even when Ethernet connectivity is used.
Installed ground wire
Ground wire pigtail (spade connector to the termination PCB)
Ground wire pigtail (ring terminal connected to the rear rack panel)
ETC Installation Guide
P-TS7 Rack Panel
P-TS7 Rack Panel Page 3 of 4 Electronic Theatre Controls, Inc.
Connecting Ethernet
Step 1: Terminate the network wiring in the RJ45 punch down strip using a standard 110 punch
down tool (not provided). Reference the connector label for the CAT5e wire termination
color code. The punch down connector provides insulation displacement. Do not strip the
wires.
Step 2: Snap the RJ45 connector into the bracket.
Connecting LinkPower and Auxiliary Power
Use the provided WAGO CAGE CLAMP
®
connectors to terminate the wiring to the provided LinkPower
(black and white twisted pair) and auxiliary power (red and black twisted pair) and ground wire pigtails.
Strip the ends of each wire (both installed control wires and pigtail wires) approximately 3/8” (10mm).
Step 1: Terminate the installed LinkPower wiring to the white and black LinkPower pigtail. Using
two WAGO connectors connect (typically white) installed wire(s) with white pigtail wire and
connect the (typically black) installed wire(s) with black pigtail wire as shown below.
Step 2: Plug the LinkPower connector into the two-pin LinkPower receptacle on the termination
PCB.
Step 3: Terminate the installed Auxiliary power conductors to the red and black Auxiliary power
pigtail wires. Using two WAGO connectors connect the (typically red) installed wire(s) with
red pigtail wire and connect the (typically black) installed wire(s) with black pigtail wire.
Step 4: Plug the auxiliary power connector into the two-pin “Aux” power receptacle on the PCB.
Installing the Touchscreen
Step 1: Install the RJ11 control cable provided in the installation kit to the RJ11 jack on the
termination PCB. Also attach the RJ45 control cable if PoE will be used for communication
and power.
Note:
All ethernet terminations must follow IEEE 802.3 and be terminated to the T568B
standard.
Note:
A 14AWG ground connection is required for all touchscreen assemblies.
The RJ11 cable provides the ground connection to the rack panel and must
always be installed.
Ground spade
PCB
24 Vdc Aux
power
connector
RJ45
Mounting bracket
ULP connector
RJ45 Ethernet with
(PoE to touchscreen)
RJ11 connector
(provides LinkPower and
Aux power to touchscreen)
Per conductor topology
of a single station
installation
Per conductor topology
of multiple stations
installed in series
Installed control wire
Pigtail wire
Installed control wire
Installed control wire to next station
Pigtail wire
ETC Installation Guide
P-TS7 Rack Panel
P-TS7 Rack Panel Page 4 of 4 Electronic Theatre Controls, Inc.
Step 2: Plug the other end of the cable(s) into the receptacles on the touchscreen.
Step 3: Hold the touchscreen with the top tilted back at a slight angle. First insert the top into the
rack panel and hook the bracket onto the pins on each side of the collar. This places the
unit in the service position, granting access to the bottom interface.
Step 4: To move the touchscreen from the service position to the operation position, lift to unhook
the pins and rotate the bottom inward until the touchscreen face is vertical.
Step 5: Apply firm pressure simultaneously to the center of the left and right edges of the
touchscreen, pushing the unit inward until it audibly snaps onto the collar. When properly
installed, the touchscreen should not easily unsnap from the collar.
Step 6: To open or remove the touchscreen, insert a flat bladed screwdriver into the pry slot
(indicated below) and unsnap the touchscreen from the collar. Then lift the bottom upward
slightly and rotate outward.
Indicators
After the touchscreen has been powered up, the appropriate LEDs on the service panel on the bottom
of the touchscreen illuminate. The LCD displays a startup screen a few seconds after booting.
I/O Indicators
• Reset - when pressed, resets the Portable LCD software
• Mode - press once for Setup menu. Press and hold for 4 seconds to calibrate the touchscreen
• PoE - indicates when the touchscreen is powered by Power over Ethernet 802.3af
• Aux - indicates the touchscreen is powered by Aux 24 Vdc
• Act - application activity is detected
• Svc - when pressed, sends the stations Neuron ID to the connected processor
• Svc - service pin indicator
• Data (LON) - indicates LON network activity
• Data (NET) - indicates Ethernet network activity
Service position
Operating position
The touchscreen bracket is
designed for two positions,
service and operation.
Hang the bracket arms on
the collar mounting pins to
rest in the service position,
granting access to the ports
and indicators on the bottom
of the unit.
SD card slot
USB Port
Pry slot
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

ETC Unison Paradigm P-TS7 Guida d'installazione

ETC
Marca
ETC
Modello
Unison Paradigm P-TS7
Tipo
Guida d'installazione
Scarica PDF
rapporto

in altre lingue

Altri documenti