Brother PE800 Guida utente

Tipo
Guida utente
Operation Manual
Embroidery Machine
Product Code: 888-L90/L91/L93/K90/K92
Be sure to read this document before using the machine.
We recommend that you keep this document nearby for future reference.
INTRODUCTION
i
Thank you for purchasing this machine. Before using this machine, carefully read the “IMPORTANT SAFETY
INSTRUCTIONS”, and then study this manual for the correct operation of the various functions.
In addition, after you have finished reading this manual, store it where it can quickly be accessed for future reference.
Please read these safety instructions before attempting to use the machine.
DANGER - To reduce the risk of electrical shock
1Always unplug the machine from the electrical outlet immediately after using, when cleaning, making any user
servicing adjustments mentioned in this manual, or if you are leaving the machine unattended.
WARNING - To reduce the risk of burns, fire, electrical shock, or injury to
persons.
2Always unplug the machine from the electrical outlet when making any adjustments mentioned in the instruction
manual.
To unplug the machine, switch the machine to the symbol “O” position to turn it off, then grasp the plug and pull
it out of the electrical outlet. Do not pull on the cord.
Plug the machine directly into the electrical outlet. Do not use an extension cord.
Always unplug your machine if there is a power failure.
3Electrical Hazards:
This machine should be connected to an AC power source within the range indicated on the rating label. Do not
connect it to a DC power source or converter. If you are not sure what kind of power source you have, contact a
qualified electrician.
This machine is approved for use in the country of purchase only.
4Never operate this machine if it has a damaged cord or plug, if it is not working properly, has been dropped or
damaged, or water is spilled on the unit. Return the machine to the nearest authorized Brother dealer for
examination, repair, electrical or mechanical adjustment.
While the machine is stored or in use if you notice anything unusual, such as an odor, heat, discoloration or
deformation, stop using the machine immediately and unplug the power cord.
When transporting the machine, be sure to carry it by its handle. Lifting the machine by any other part may
damage the machine or result in the machine falling, which could cause injuries.
When lifting the machine, be careful not to make any sudden or careless movements, which may cause a
personal injury.
INTRODUCTION
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
ii
5Always keep your work area clear:
Never operate the machine with any air openings blocked. Keep ventilation openings of the machine and foot
control free from the build up of lint, dust, and loose cloth.
Do not use extension cords. Plug the machine directly into the electrical outlet.
Never drop or insert foreign objects in any opening.
Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
Do not use the machine near a heat source, such as a stove or iron; otherwise, the machine, power cord or
garment being sewn may ignite, resulting in fire or an electric shock.
Do not place this machine on an unstable surface, such as an unsteady or slanted table, otherwise the machine
may fall, resulting in injuries.
6Special care is required when embroidering:
Always pay close attention to the needle. Do not use bent or damaged needles.
Keep fingers away from all moving parts. Special care is required around the machine needle.
Switch the machine to the symbol “O” position to turn it off when making any adjustments in the needle area.
Do not use a damaged or incorrect needle plate, as it could cause the needle to break.
7This machine is not a toy:
Your close attention is necessary when the machine is used by or near children.
The plastic bag that this machine was supplied in should be kept out of the reach of children or disposed of.
Never allow children to play with the bag due to the danger of suffocation.
Do not use outdoors.
8For a longer service life:
When storing this machine, avoid direct sunlight and high humidity locations. Do not use or store the machine
near a space heater, iron, halogen lamp, or other hot objects.
Use only neutral soaps or detergents to clean the case. Benzene, thinner, and scouring powders can damage the
case and machine, and should never be used.
Always consult the Operation Manual when replacing or installing needle or other parts to assure correct
installation.
9For repair or adjustment:
If the light unit is damaged, it must be replaced by an authorized Brother dealer.
In the event a malfunction occurs or adjustment is required, first follow the troubleshooting table in the back of
the Operation Manual to inspect and adjust the machine yourself. If the problem persists, please consult your
local authorized Brother dealer.
Use this machine only for its intended use as described in the manual.
Use accessories recommended by the manufacturer as contained in this manual.
The contents of this manual and specifications of this product are subject to change without notice.
For additional product information and updates, visit our website at www.brother.com
IMPORTANT SAFETY INSTRUCTIONS
iii
SAVE THESE INSTRUCTIONS
This machine is intended for household use.
FOR USERS IN COUNTRIES EXCEPT CENELEC COUNTRIES
This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety. Children should be supervised
to ensure that they do not play with the appliance.
FOR USERS IN CENELEC COUNTRIES
This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved. Children shall not
play with the appliance. Cleaning and user maintenance shall not be made by
children without supervision.
FOR USERS IN THE UK, EIRE, MALTA
AND CYPRUS ONLY
IMPORTANT
In the event of replacing the plug fuse, use a fuse approved by ASTA to BS 1362, i.e. carrying the mark,
rating as marked on plug.
Always replace the fuse cover. Never use plugs with the fuse cover omitted.
If the available electrical outlet is not suitable for the plug supplied with this equipment, you should contact your
authorized Brother dealer to obtain the correct lead.
TRADEMARKS
iv
TRADEMARKS
IMPORTANT:
READ BEFORE DOWNLOADING, COPYING, INSTALLING OR USING.
By downloading, copying, installing or using the software you agree to this license. If you do not agree
to this license, do not download, install, copy or use the software.
Intel License Agreement For Open Source Computer Vision Library
Copyright © 2000, Intel Corporation, all rights reserved. Third party copyrights are property of their respective owners.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the
following conditions are met:
Redistribution’s of source code must retain the above copyright notice, this list of conditions and the following
disclaimer.
Redistribution’s in binary form must reproduce the above copyright notice, this list of conditions and the
following disclaimer in the documentation and/or other materials provided with the distribution.
The name of Intel Corporation may not be used to endorse or promote products derived from this software
without specific prior written permission.
This software is provided by the copyright holders and contributors “as is” and any express or implied warranties,
including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose are
disclaimed. In no event shall Intel or contributors be liable for any direct, indirect, incidental, special, exemplary,
or consequential damages (including, but not limited to, procurement of substitute goods or services; loss of use,
data, or profits; or business interruption) however caused and on any theory of liability, whether in contract, strict
liability, or tort (including negligence or otherwise) arising in any way out of the use of this software, even if
advised of the possibility of such damage.
All information provided related to future Intel products and plans is preliminary and subject to change at any time, without notice.
WHAT YOU CAN DO WITH THIS MACHINE
v
WHAT YOU CAN DO WITH THIS MACHINE
B Basic operations
After purchasing your machine, be sure to read this section first. This section provides details on the initial setup
procedures as well as descriptions of this machine’s more useful functions.
Chapter 1 GETTING READY
Page B-2
To learn the operation of the principal parts and the screens
Chapter 2 STARTING TO EMBROIDER
Page B-25
To learn how to prepare for embroidering and basic embroidering operations
E Embroidering
This section provides instruction on editing embroidery patterns and recalling stored embroidery patterns.
Chapter 1 EMBROIDERY
Page E-2
Embroider artistically; by editing the built-in patterns you can easily create your own original designs.
A Appendix
This section provides important information for operating this machine.
Chapter 1 MAINTENANCE AND TROUBLESHOOTING
Page A-2
The various maintenance and troubleshooting procedures are described.
CONTENTS
vi
INTRODUCTION.................................................. i
IMPORTANT SAFETY INSTRUCTIONS ................. i
TRADEMARKS ..................................................... iv
WHAT YOU CAN DO WITH THIS MACHINE ..... v
B Basic operations
Chapter 1 GETTING READY 2
Names of Machine Parts and Their Functions....... 2
Machine................................................................................. 2
Needle and presser foot section ................................................... 3
Embroidery Unit..................................................................... 3
Operation buttons .................................................................. 4
Operation panel and operation keys....................................... 4
Included accessories .............................................................. 5
Optional accessories .............................................................. 6
Turning the Machine On/Off................................ 7
Turning on the machine ......................................................... 8
Turning off the machine ......................................................... 8
Select machine setting for the first time .................................. 8
LCD Operation ..................................................... 9
Viewing the LCD.................................................................... 9
Using the settings key........................................................... 10
Adjusting input sensitivity for operation keys........................ 12
Saving a settings screen image to USB flash drive................. 13
Checking machine operating procedures.............................. 13
Winding/Installing the Bobbin............................ 14
Winding the bobbin ............................................................. 14
Installing the bobbin............................................................. 17
Upper Threading ................................................ 19
Threading the upper thread .................................................. 19
Threading the needle............................................................ 21
Threading the needle manually (without using the needle
threader)............................................................................... 22
Replacing the Needle.......................................... 23
Checking the needle............................................................. 23
Replacing the needle............................................................ 23
Chapter 2 STARTING TO EMBROIDER 25
Embroidery Step by Step..................................... 25
Attaching the Embroidery Unit........................... 26
Embroidery Attractive Finishes........................... 28
Preparing the Fabric ........................................... 29
Attaching iron-on stabilizers (backing) to the fabric .............. 29
Hooping the fabric in the embroidery frame......................... 30
Embroidering small fabrics or fabric edges ........................... 32
Attaching the Embroidery Frame........................ 33
Selecting Embroidery Patterns ............................ 35
Copyright information .......................................................... 35
Embroidery pattern types...................................................... 35
Selecting an embroidery pattern ........................................... 35
Confirming the Pattern Position ......................... 36
Checking the pattern position............................................... 36
Previewing the selected pattern ............................................ 36
Embroidering...................................................... 37
Embroidering a pattern ......................................................... 37
Changing the thread color display ........................................ 38
E Embroidering
Chapter 1 EMBROIDERY 2
Selecting Patterns................................................. 2
Selecting embroidery patterns/Brother “Exclusives”/floral
alphabet patterns ................................................................... 2
Selecting character patterns ................................................... 2
Selecting frame patterns......................................................... 4
Editing Patterns .................................................... 5
Moving the pattern ................................................................ 6
Changing the size of the pattern............................................. 6
Rotating the pattern ............................................................... 7
Changing the thread color ..................................................... 7
Creating a horizontal mirror image ........................................ 7
Changing the density (alphabet character and frame
patterns only)......................................................................... 8
Deleting the pattern............................................................... 8
Displaying patterns in the screen magnification ..................... 8
After editing........................................................................... 8
Editing Character Patterns ................................... 9
Changing the colors of alphabet character patterns................ 9
Switching between text written vertically and horizontally .... 9
Changing the font of entered characters............................... 10
Changing character spacing................................................. 10
Separating combined character patterns .............................. 10
Editing single characters ...................................................... 11
Changing the configuration of character patterns................. 12
Combining Patterns............................................ 13
Editing combined patterns ................................................... 13
Embroidering combined patterns ......................................... 14
Editing All Patterns............................................. 15
Moving the pattern .............................................................. 15
Rotating the pattern ............................................................. 15
Aligning the pattern and the needle ..................................... 15
Embroidering linked characters............................................ 16
Embroidery Applications.................................... 18
Sewing embroidery patterns which use appliqué ................. 18
Using a frame pattern to make an appliqué (1)..................... 20
Using a frame pattern to make an appliqué (2)..................... 21
Sewing split embroidery patterns ......................................... 22
Adjustments During the Embroidery Process ..... 23
If the bobbin runs out of thread............................................ 23
If the thread breaks during sewing ....................................... 24
Restarting from the beginning .............................................. 24
Resuming embroidery after turning off the power ................ 24
Making Embroidery Adjustments ....................... 26
Adjusting thread tension ...................................................... 26
Adjusting the bobbin case (with no color on the screw) ....... 27
Using the automatic thread cutting function
(END COLOR TRIM)............................................................ 28
Adjusting the embroidery speed........................................... 28
Changing the “Embroidery Frame Display”.......................... 28
Selecting/displaying patterns according to the embroidery
frame size ............................................................................ 29
Changing the background colors of the embroidery
patterns................................................................................ 30
Specifying the size of pattern thumbnails............................. 30
Using the Memory Function............................... 31
Embroidery data precautions ............................................... 31
Saving embroidery patterns in the machine’s memory ......... 32
Saving embroidery patterns to USB flash drive..................... 33
Retrieving patterns from the machine’s memory .................. 34
Recalling from USB flash drive ............................................ 34
CONTENTS
CONTENTS
vii
A Appendix
Chapter 1 MAINTENANCE AND
TROUBLESHOOTING 2
Care and Maintenance ......................................... 2
Restrictions on oiling ............................................................. 2
Precautions on storing the machine ....................................... 2
Cleaning the LCD Screen ....................................................... 2
Cleaning the machine surface ................................................ 2
Cleaning the race................................................................... 2
About the maintenance message ............................................ 4
Touch panel is malfunctioning ............................................... 4
Operation beep...................................................................... 4
Replacing the embroidery foot ............................................... 5
Troubleshooting ................................................... 6
List of symptoms .................................................................... 6
Error messages ..................................................................... 10
Upgrading your machine’s software using
USB flash drive................................................... 12
Index .................................................................. 13
CONTENTS
viii
Basic
operations
This section provides details on the initial setup procedures as well as descriptions of this
machine’s more useful functions.
Page number starts with “B” in this section.
Chapter1 GETTING READY....................................................... B-2
Chapter2 STARTING TO EMBROIDER................................. B-25
Names of Machine Parts and Their Functions
B-2
The names of the various parts of the machine and their functions are described below. Before using the machine,
carefully read these descriptions to learn the names of the machine and their locations.
Machine
Front view
1 Top cover
Open the top cover to place the spool of thread on the spool
pin.
2 Thread guide plate
Pass the thread around the thread guide plate when threading
the upper thread.
3 Bobbin winding thread guide and pretension disk
Pass the thread under this thread guide and around the
pretension disk when winding the bobbin thread.
4 Spool cap
Use the spool cap to hold the spool of thread in place.
5 Spool pin
Place a spool of thread on the spool pin.
6 Bobbin winder
Use the bobbin winder when winding the bobbin.
7 LCD (liquid crystal display)
Settings for the selected pattern and error messages appear in
the LCD. (page B-9)
8 Operation panel
From the operation panel, embroidery patterns can be selected
and edited, and operations for using the machine can be
selected. (page B-4)
9 Operation buttons
Use these buttons to operate the machine. (page B-4)
0 Embroidery unit
Attach embroidery unit to embroider. (page B-26)
A Thread cutter
Pass the threads through the thread cutter to cut them.
B Needle threader lever
Use the needle threader lever to thread the needle.
Right-side/rear view
1 Handwheel
Turn the handwheel toward you (counterclockwise) to raise and
lower the needle.
2 Handle
Carry the machine by its handle when transporting.
3 Presser foot lever
Raise and lower the presser foot lever to raise and lower the
presser foot.
4 Main power switch
Use the main power switch to turn the machine on and off.
5 Power supply jack
Insert the plug on the power cord into the power supply jack.
6 Air vent
The air vent allows the air surrounding the motor to circulate.
Do not cover the air vent while the machine is being used.
7 USB port (for a USB flash drive)
In order to import patterns from a USB flash drive, insert the
USB flash drive directly into the USB port.
Chapter 1
GETTING READY
Names of Machine Parts and Their Functions
a
b
c
d
e
f
h
k
l
g
i
j
a
b
c
d
e
g
f
Names of Machine Parts and Their Functions
Basic operations B-3
GETTING READY
B
Needle and presser foot section
1 Needle bar thread guide
Pass the upper thread through the needle bar thread guide.
2 Needle plate
3 Needle plate cover
Remove the needle plate cover to clean the bobbin case and
race.
4 Bobbin cover/bobbin case
Remove the bobbin cover and then insert the bobbin into the
bobbin case.
5 Embroidery foot
The embroidery foot helps control fabric flexibility for better
stitch consistency.
6 Embroidery foot screw
Use the embroidery foot screw to hold the embroidery foot in
place.
Embroidery Unit
1 Frame-securing lever
Press the frame-securing lever to the left to attach or remove
the embroidery frame. (page B-33)
2 Embroidery unit connector
Insert the embroidery unit connector into the connection port
when attaching the embroidery unit. (page B-26)
3 Carriage
The carriage moves the embroidery frame automatically when
embroidering. (page B-26)
4 Release button (located under the embroidery unit)
Press the release button to remove the embroidery unit.
(page B-27)
b
a
c
d
e
f
CAUTION
Before inserting or removing the embroidery
unit, turn the main power to OFF.
d
a
b
c
Names of Machine Parts and Their Functions
B-4
Operation buttons
1 “Start/Stop” button
Press the “Start/Stop” button to start or stop embroidering.
The button changes color according to the machine’s
operation mode.
2 Needle position button
Press the needle position button to raise or lower the needle.
3 Thread cutter button
Press the thread cutter button after embroidering is stopped to
cut both the upper and the bobbin threads.
Operation panel and operation keys
1 LCD (liquid crystal display) (touch panel)
Selected pattern settings and messages are displayed.
Touch the keys displayed on the LCD to perform operations.
For details, refer to “LCD Operation” on page B-9.
2 Previous page key
Displays the previous screen when there are items that are not
displayed on the LCD.
3 Next page key
Displays the next screen when there are items that are not
displayed on the LCD.
4 Help key
Press to get help on using the machine.
5 Settings key
Press to set the needle stop position, the buzzer sound, and
more.
6 Embroidery key
Press this key to sew embroidery.
7 Back key
Press to return to the previous screen.
8 Presser foot/Needle exchange key
Press this key before changing the needle, the presser foot,
etc. This key locks all key and button functions to prevent
operation of the machine.
Green: The machine is ready to embroider or is
embroidering.
Red: The machine can not embroider.
Orange: The machine is winding the bobbin thread, or
the bobbin winder shaft is moved to the right
side.
CAUTION
Do not press (Thread cutter button) after
the threads have already been cut, otherwise
the needle may break, the threads may
become tangled or damage to the machine
may occur.
bc
a
Note
The operation keys of this machine are
capacitive touch sensors. Operate the keys by
directly touching them with your finger.
The response of the keys varies according to the
user. The pressure exerted on the keys does not
affect the response of the keys.
Since the operation keys react differently
depending on the user, adjust the setting for
“Adjusting input sensitivity for operation keys” on
page B-12.
When using an electrostatic touch pen, make
sure that its point is 8 mm or more. Do not use a
touch pen with a thin point or a unique shape.
a
b
c
d
e
f
g
h
Names of Machine Parts and Their Functions
Basic operations B-5
GETTING READY
B
Included accessories
Included accessories may differ from the table below depending on the machine model you purchased. For more details on
included accessories and their part codes of your machine, refer to the Quick Reference Guide.
1. 2. 3. 4. 5. 6.
Embroidery foot “Q
(on machine)
Needle set
2/11 needle
Bobbin (4)
(One is on machine.)
Seam ripper Scissors Cleaning brush
7. 8. 9. 10. 11. 12.
Screwdriver (large) Screwdriver (small) Disc-shaped screwdriver Spool cap (large) Spool cap (medium)
(on machine)
Spool cap (small)
13. 14. 15. 16. 17.
Thread spool insert
(mini king thread spool)
Spool net Bobbin case
(no color on the screw)
(on machine)
Embroidery frame set (large)
18 cm (H) × 13 cm (W) (7 inches (H) × 5 inches (W))
Poly 90 weight bobbin thread
18. 19. 20. 21. 22.
Accessory bag Dust cover Operation Manual Quick Reference Guide Embroidery Design Guide
Q
Names of Machine Parts and Their Functions
B-6
Optional accessories
The following are available as optional accessories to be purchased separately. For more optional accessories and their part
codes, refer to the Quick Reference Guide.
1. 2. 3.
Embroidery frame set (extra large (multi-position))
30 cm (H) × 13 cm (W) (12 inches (H) × 5 inches (W))
Embroidery frame set (medium)
10 cm (H) × 10 cm (W) (4 inches (H) × 4 inches (W))
Embroidery frame set (small)
2 cm (H) × 6 cm (W) (1 inch (H) × 2-1/2 inches (W))
4. 5.
Stabilizer material for
embroidery
Water soluble stabilizer
Memo
To obtain optional accessories or parts, contact your authorized Brother dealer.
All specifications are correct at the time of printing. Please be aware that some specifications may change without
notice.
Visit your nearest authorized Brother dealer for a complete listing of optional accessories available for your machine.
Always use accessories recommended for this machine.
Turning the Machine On/Off
Basic operations B-7
GETTING READY
B
Turning the Machine On/Off
Use only regular household electricity for the power source. Using other power sources may result in fire,
electric shock, or damage to the machine.
Make sure that the plugs on the power cord are firmly inserted into the electrical outlet and the power
cord receptacle on the machine. Otherwise, a fire or electric shock may result.
Do not insert the plug on the power cord into an electrical outlet that is in poor condition.
Turn the main power to OFF and remove the plug in the following circumstances:
When you are away from the machine
After using the machine
When the power fails during use
When the machine does not operate correctly due to a bad connection or a disconnection
During electrical storms
Use only the power cord included with this machine.
Do not use extension cords or multi-plug adapters with any other appliances plugged into them. Fire or
electric shock may result.
Do not touch the plug with wet hands. Electric shock may result.
When unplugging the machine, always turn the main power to OFF first. Always grasp the plug to remove
it from the electrical outlet. Pulling on the cord may damage the cord, or lead to fire or electric shock.
Do not allow the power cord to be cut, damaged, modified, forcefully bent, pulled, twisted, or bundled.
Do not place heavy objects on the cord. Do not subject the cord to heat. These things may damage the
cord, or cause fire or electric shock. If the cord or plug is damaged, take the machine to your authorized
Brother dealer for repairs before continuing use.
Unplug the power cord if the machine is not to be used for a long period of time. Otherwise, a fire may
result.
When leaving the machine unattended, either the main switch of the machine should be turned to OFF or
the plug must be removed from the electrical outlet.
When servicing the machine or when removing covers, the machine must be unplugged.
•(For U.S.A. only)
This appliance has a polarized plug (one blade wider than the other). To reduce the risk of electrical
shock, this plug is intended to fit in a polarized electrical outlet only one way.
If the plug does not fit fully in the electrical outlet, reverse the plug. If it still does not fit, contact a
qualified electrician to install the proper electrical outlet. Do not modify the plug in any way.
Turning the Machine On/Off
B-8
Turning on the machine
a
Make sure that the machine is turned off (the main
power switch is set to “ ”), and then plug the power
cord into the power supply jack on the right side of the
machine.
b
Insert the plug of the power cord into a household
electrical outlet.
1 Power supply jack
2 Main power switch
c
Press the right side of the main power switch on the
right side of the machine to turn the machine on (set it
to “I”).
The light, LCD and the “Start/Stop” button light up
when the machine is turned on.
d
When the machine is turned on, the opening movie is
played. Press anywhere on the screen.
Turning off the machine
When you are finished using the machine, turn it off. In
addition, before transporting the machine to another location,
be sure to turn it off.
a
Make sure that the machine is not embroidering.
b
Press the main power switch on the right side of the
machine in the direction of the “ symbol to turn
the machine off.
Select machine setting for the first time
When you first turn on the machine, select the language of
your choice. Follow the procedure below when the settings
screen appears automatically.
a
Press and to select your choice of language.
b
Press .
Memo
When the machine is turned on, the machine will
make a sound when it moves; this is not a
malfunction.
If the machine is turned off in the middle of
embroidering, the operation will resume after
turning the power on again.
1
2
LCD Operation
Basic operations B-9
GETTING READY
B
Viewing the LCD
An opening movie may be displayed when the power is turned on. When the opening movie is displayed, the screen will be
displayed if you touch the LCD with your finger. Press a key with your finger to select the embroidery pattern, to select a machine
function, or to select an operation indicated on the key.
The screen below appears after the embroidery carriage moves to its initial position.
LCD Operation
1 Embroidery patterns
2 Brother “Exclusives”
3 Floral alphabet patterns
4 Character patterns
5 Frame patterns
6 Press this key to position the embroidery unit for
storage
7 Patterns saved in the machine's memory
8 Patterns saved in USB flash drive
ab
c
e
h
gd
f
LCD Operation
B-10
Using the settings key
Press to change the default machine settings (needle stop position, embroidery speed, opening display, etc.). Press ,
after you changed necessary settings.
Embroidery settings
1 Select the embroidery frame to be used.
2 Select the centerpoint marker and grid that are displayed. For details, refer to “Changing the “Embroidery Frame Display”” in the
“Embroidering” section.
3 When set to “ON”, the embroidery pattern can be selected according to the embroidery frame size that you have selected in
number
1. For details, refer to “Selecting/displaying patterns according to the embroidery frame size” in the “Embroidering”
section.
4 Change the thread color display on the “Embroidery” screen; thread number, color name. (page B-38).
5 When the thread number “#123” is selected, select from six thread brands. (page B-38).
6 Adjust the maximum embroidery speed setting. For details, refer to “Adjusting the embroidery speed” in the “Embroidering”
section.
7 Change the display units (mm/inch).
8 Adjust the upper thread tension for embroidering. For details, refer to “Adjusting thread tension” in the “Embroidering” section.
9 Press to specify the size of pattern thumbnails. For details, refer to “Specifying the size of pattern thumbnails” in the
“Embroidering” section.
0 Change the color of the background for the embroidery display area. For details, refer to “Changing the background colors of the
embroidery patterns” in the “Embroidering” section.
A Change the color of the background for the thumbnail area. For details, refer to “Changing the background colors of the
embroidery patterns” in the “Embroidering” section.
Page 1 Page 2 Page 3
3
2
1
4
5
6
7
8
9
A
0
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100

Brother PE800 Guida utente

Tipo
Guida utente

in altre lingue